STSC1518 | Stanley STSC1518 CIRCULAR SAW instruction manual

STSC1518
English(Original)
Page 4
(Original instructions)
ENGLISH
FIG. A
FIG. B
FIG. C
FIG. D
FIG. E
2
1
3
7
9
8
4
10
5
6
FIG. F
4
2
13
11
12
FIG. G
(Original instructions)
FIG. H
ENGLISH
FIG. I
15
11
8
4
9
14
FIG. K
FIG. J
11
10
5
15
8
10
16
FIG. M
FIG. L
19
19
8
17
18
3
ENGLISH
(Original instructions)
Intended Use
Your STANLEY saw has been designed for sawing wood
and wood products. This tool is intended for consumer use
only
•
For tools intended to cut wood, instruction on correct
use of the dust collection system.
•
For tools intended to cut wood, instruction to wear a
dust mask.
•
Instrcution to only use saw blades recommended.
•
Instruction to always wear hearing protection.
DO NOT RETURN THIS PRODUCT TO THE STORE,
first contact your local STANLEY Office
or nearest authorized service center.
General Safety Rules
Warning! Read and understand all instructions.
Failure to follow all instructions listed below, may
result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
Safety instructions
General power tool safety warnings
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below
refers to your mains operated (corded) power tool or battery
operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose
control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk
of electric shock.
4
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric
shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock. Note: The term “Residual Curent Device
(RCD)” can be replaced by “Ground Fault Circuit
Interrupter (GFCI)” or by “Earth Leakage Circuit Breaker
(ELCB)”.
3. Personal safety
a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is
in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch on
invites accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
e. Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
(Original instructions)
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is
maintained.
ENGLISH
Additional power tool safety warnings
Warning! Safety instructions for all saws
Cutting procedures
Danger! Keep hands away from cutting area
and the blade. Keep your second hand on
auxiliary handle, or motor housing. If both
hands are holding the saw, they cannot be cut by the blade.
b. Do not reach underneath the workpiece. The guard
cannot protect you from the blade below the workpiece.
c. Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
d. Never hold piece being cut in your hands or across
your leg. Secure the workpiece to a stable platform. It
is important to support the work properly to minimize
body exposure, blade binding, or loss of control.
e. Hold the power tool by insulated gripping surfaces
only, when performing an operation where the
cutting tool may contact hidden wiring. Contact with a
"live" wire will also make exposed metal parts of the
power tool "live" and could give the operator an electric
shock.
f. When ripping, always use a rip fence or straight
edge guide. This improves the accuracy of cut and
reduces the chance of blade binding.
g. Always use blades with correct size and shape
(diamond versus round) of arbour holes. Blades that
do not match the mounting hardware of the saw will run
eccentrically, causing loss of control.
h. Never use damaged or incorrect blade washers or
bolt. The blade washers and bolt were specially
designed for your saw, for optimum performance and
safety of operation.
Kickback Causes And Related Warnings
•
Kickback is a sudden reaction to a pinched, bound or
misaligned saw blade, causing an uncontrolled saw tolift
upandoutoftheworkpiecetowardtheoperator.
5
ENGLISH
(Original instructions)
•
When the blade is pinched or bound tightly by the kerf
closing down, the blade stalls and the motor reaction
drives the unit rapidly back toward the operator.
g. Use extra caution when making a “Pocket Cut” into
existing walls or other blind areas. The protruding
blade may cut objects that can cause kickback.
•
If the blade becomes twisted or misaligned in the cut,
the teeth at the back edge of the blade can dig into the
top surface of the wood causing the blade to climb out of
the kerf and jump back toward operator.
Lower guard function
•
Kickback is the result of tool misuse and/or incorrect
operating procedures or conditions and can be avoided
by taking proper precautions as given below.
a. Maintain a firm grip with both hands on the saw and
position your body and arm to allow you to resist
kickback forces. Kickback forces can be controlled by
the operator, if proper precautions are taken.
b. When blade is binding, or when interrupting a cut
for any reason, release the trigger and hold the saw
motionless in the material until the blade comes to a
complete stop. Never attempt to remove the saw
from the work or pull the saw backward while the
blade is in motion or kickback may occur. Investigate
and take corrective actions to eliminate the cause of
blade binding.
c. When restarting a saw in the workpiece, center the
saw blade in the kerf and check that the saw teeth
are not engaged into the material. If saw blade is
binding, it may walk up or kickback from the workpiece
as the saw is restarted.
d. Support large panels to minimize the risk of blade
pinching and kickback. Large panels tend to sag under
their own weight. Support must be placed under the
panel on both sides, near the line of cut and near the
edge of the panel.
a. Check lower guard for proper closing before each
use. Do not operate the saw if lower guard does not
move freely and close instantly. Never clamp or tie
the lower guard into the open position. If saw is
accidentally dropped, lower guard may be bent. Raise
the lower guard with the retracting handle and make sure
it moves freely and does not touch the blade or any other
part, in all angles and depths of cut.
b. Check the operation of the lower guard spring. If the
guard and the spring are not operating properly, they
must be serviced before use. Lower guard may
operate sluggishly due to damaged parts, gummy
deposits, or a build-up of debris.
c. Lower guard may be retracted manually only for
special cuts such as "plunge cuts" and "compound
cuts". Raise lower guard by retracting handle and as
soon as blade enters the material, the lower guard must
be released. For all other sawing, the lower guard should
operate automatically.
d. Always observe that the lower guard is covering the
blade before placing saw down on bench or floor. An
unprotected, coasting blade will cause the saw to walk
backwards, cutting whatever is in its path. Be aware of
the time it takes for the blade to stop after switch is
released.
Residual risks
e. Do not use dull or damaged blade. Unsharpened or
improperly set blades produce narrow kerf causing
excessive friction, blade binding, and kickback.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
f. Blade depth and bevel adjusting locking levers must
be tight and secure before making cut. If blade
adjustment shifts while cutting, it may cause binding and
kickback.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
6
(Original instructions)
ENGLISH
•
Injuries caused by touching any rotating/moving parts.
•
Lead from lead-based paints,
•
Injuries caused when changing any parts, blades or
accessories.
•
Crystalline silica from bricks and cement and other
masonry products,
•
Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
•
Arsenic and chromium from chemically-treated lumber
(CCA).
•
Impairment of hearing.
•
Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Safety Guidelines/definitions
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals:
•
Work in a well ventilated area, and work with approved
safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
•
Avoid prolonged contact with dust from power
sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing and
wash exposed areas with soap and water. Allowing
dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
It is important for you to read and understand this manual.
The information it contains relates to protecting Your Safety
and Preventing Problems. The symbols below are used to
help you recognize this information.
Danger! Indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
Warning! Indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
Caution! Indicates a potentially hazardous
situation which, if not avoided, may result in minor
or moderate injury.
Caution! Used without the safety alert symbol
indicates potentially hazardous situation which, if
not avoided, may result in property damage.
Additional Safety Rules For Circular Saws
Warning! Some dust created by power
sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
Caution! Wear appropriate hearing protection
during use. Under some conditions and duration of
use, noise from this product may contribute to hearing loss.
•
Snagging the lower guard on a surface below the
material being cut can momentarily reduce operator
control. The saw can lift partially out of the cut
increasing the chance of blade twist. Ensure there is
sufficient clearance under the workpiece.
•
When necessary to raise lower guard manually, use
the retracting lever.
•
Keep the Blades Clean and Sharp. Sharp blades
minimize stalling and kickback. The use of dull and/ or
dirty blades can increase the saw loading causing the
operator to push harder which promotes twisting.
Caution! Laceration Hazard. Keep hands away from
cutting areas. Keep hands away from blades. Never place
hands in front of or behind the path of the blade while
cutting. Do not reach underneath work while blade is
rotating. Do not attempt to remove cut material when blade
is moving.
7
ENGLISH
•
•
(Original instructions)
Support large panels. Large panels must be supported
as shown (Fig. A) in this manual to minimize the risk of
blade pinching and kickback. Material supported only at
the ends (Fig. B) will lead to blade pinching. When
cutting operation requires the resting of the saw on the
workpiece, the saw shall be rested on the larger portion
and the smaller piece cut off.
Position of date barcode
Use only correct blades and blade assembly
components when mounting blades. Do not use
blades with incorrect size holes. Never use defective or
incorrect blade washers or bolts. Follow blade assembly
procedures.
Electrical safety
Saw blades
•
Do not use blades of larger or smaller diameter than
recommended. For the proper blade rating refer to the
technical data. Use only the blades specified in this
manual, complying with EN 847-1.
Warning! Never use abrasive wheels.
The Date Code, which also includes the year of
manufacture, is printed into the housing.
Example:
2014 XX JN
Year of manufacturing
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
STANLEY Service Center or an equally qualified person in
order to avoid damage or injury. If the power cord is replaced
by an equally qualified person, but not authorized by
STANLEY, the warranty will not be valid.ce.
Vibration
Safety of others
•
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
•
Children should be supervised to ensure that they do
not play with the appliance.
The declared vibration emission values stated in the
technical data and the declaration of conformity have been
measured in accordance with a standard test method
provided by EN 60745 and may be used for comparing one
tool with another. The declared vibration emission value may
also be used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level
may increase above the level stated.
Labels on tool
When assessing vibration exposure to determine safety
The label on your tool may include the following symbols: measures required by 2002/44/EC to protect persons
regularly using power tools in employment, an estimation of
Hz ....... Hertz
...... Class II
Read
vibration exposure should consider, the actual conditions of
Construction
Instructions
W ........ Watts
Manual
use and the way the tool is used, including taking account of
.... Earthing
min ..... minutes
Terminal
Use Eye
all parts of the operating cycle such as the times when the
Protection
..... Alternating
.... Safety Alert
tool is switched off and when it is running idle in addition to
Current
Symbol
Use Ear
the trigger time.
Protection
..... Direct
Current
V ........ Volts
A ........ Amperes
8
n 0 ....... No-Load
Speed
.../min..
Revolutions
or Reciprocation per
minute
•
Adjustments. Before cutting be sure depth and bevel
adjustments are tight.
•
Support and secure the work properly. Insure that the
material to be cut is clamped (Fig. C), and solidly
(Original instructions)
•
ENGLISH
supported and balanced on a strong, stable and level
work surface. Support the work so that the wide portion
of the saw shoe is on the portion of the material that
doesn’t fall after the cut is made. Never hold cut off
piece by hand (Fig. D). Kickback from blade pinch can
result. Keep both hands on saw at all times.
corresponding depth of cut can be read from the scale (13).
Stay alert and exercise control. Keep body positioned
to one side of blade. Always maintain a firm grip and
control of saw with both hands. Do not change hand grip
or body position while saw is running. Take precaution to
avoid injury from cut off pieces and other falling material
during operation.
Adjusting the bevel angle (Fig. H)
Danger! Release switch immediately if blade
binds or saw stalls.
Features (Fig. E)
This tool includes some or all of the following features.
1. On/Off Switch
•
Tighten the lever to lock the saw shoe in place.
•
Set depth adjustment of saw such that one tooth of the
blade projects below the workpiece as shown in Fig. G.
This tool can be set to bevel angles between 0° and 45°
•
Loosen the locking knob (9) to unlock the saw shoe.
•
Move the saw shoe (4) into the desired position. The
corresponding bevel angle can be read from the scale
(14).
•
Tighten the locking knob to lock the saw shoe in place.
Attaching the blade (Fig. I and J)
•
To prevent spindle rotation engage the protrusions of the
spanner wrench (8) into the holes in the outer washer
(10) as shown in Fig. I.
•
Loosen and remove the blade retaining screw (11) by
turning the hex wrench (15) counter- clockwise.
•
Remove the outer washer.
•
Check and re-assembly inner flange (20) on spindle (16).
Insure the correct side of inner flange (20) faces outward
and match saw blade with diameter arbor well.
•
Place the saw blade (5) onto the inner flange (20),
making sure that the arrow on the blade points in the
same direction as the arrow on the tool.
•
Fit the outer washer (10) on the spindle.
•
Insert the blade retaining screw (11) into the hole in the
spindle.
•
Prevent spindle rotation by engaging the spanne wrench
into the holes of the outer washer.
•
Securely tighten the blade retaining screw by holding the
spanner wrench and turning hex wrench clockwise to
tighten the blade retaining screw.
2. Main Handle
3. Secondary Handle
4. Shoe
5. Saw Blade
6. Saw Blade Guard
7. Blade Guard Retracting Lever
8. Saw Blade Spanner Wrench
9. Bevel Adjustment Knob
10. Outer Washer
11. Blade Retaining Screw
Saw Blade Hex Wrench (Shown on Fig.I)
18. Rip Fence (Shown on Fig. M)
Inner Flange (Shown on Fig. J)
Assembly/adjustment Set-up
Warning! Always unplug saw from power supply
before any of the following operations.
Adjusting the depth of cut (Fig. F and G)
Warning! Inner flange (20) respectively marked
with “19” and “20”, match the saw blade (5) with
19mm and 20mm diameter arbor.
The depth of cut should be set according to the thickness of
the workpiece.
Removing the blade
•
Loosen the lever (12) to unlock the saw shoe.
•
Move the saw shoe (4) into the desired position. The
To prevent spindle rotation, engage the protrusions of the
spanner wrench (8) into the holes in the outer washer (10).
9
ENGLISH
(Original instructions)
•
Loosen and remove the blade retaining screw (11) by
turning it counterclockwise using the hex wrench (15).
•
Remove the outer washer (10).
•
Remove the saw blade (5). Warning! To reduce the risk
of serious personal injury, read, understand and follow
all important safety warnings and instructions prior to
using tool.
•
Work with the shoe pressed against the workpiece.
Hints For Optimum Use
•
As some splintering along the line of cut on the top side
of the workpiece cannot be avoided, cut on the side
where splintering is acceptable.
•
Where splintering is to be minimized, e.g. when cutting
laminates, clamp a piece of plywood onto the top of the
workpiece.
General Cuts
Guard against kickback
Pocket cutting (Fig. K)
With unit unplugged, follow all assembly, adjustment and set
up instructions. Make sure lower guard operates. Select the
proper blade for the material to be cut.
Pocket cutting is used to cut a hole in a piece of material
without cutting from the side.
•
Measure and mark work for cutting.
•
Support and secure work properly (See Safety Rules
and Instructions).
•
Use appropriate and required safety equipment (See
Safety Rules).
•
Secure and maintain work area (See Safety Rules).
•
With plug inserted and guard closed, make sure switch
turns saw on and off.
•
Measure and mark work.
•
Tilt saw forward and rest front of the shoe on material to
be cut. Align so that cut will begin at the back of the
drawn rectangle shown in Fig. K.
•
Using the retracting lever, retract blade guard to an
upward position, with the blade just clearing the material,
start motor and gradually lower the saw into the material.
Warning! As blade starts cutting the material,
release the retracting lever immediately.
Warning! It is important to support the work
properly and to hold the saw firmly to prevent loss
of control which could cause personal injury. Fig.
C illustrates recommended hand position.
•
Never tie the blade guard in a raised position.
•
When the shoe rests flat on the material being cut,
complete the cut in forward direction.
Operation
•
Allow the blade to come to a complete stop before lifting
saw from material.
•
When starting each new cut, repeat the above steps
Switch
•
To operate the tool, depress the trigger switch (1). The
tool will continue to run as long as the trigger is
depressed.
•
To turn the tool off, release the trigger switch (1). There
is no provision for locking the tool on, and the switch
should never be locked on by any other means.
Sawing
Warning! To reduce the risk of serious personal
injury,always hold the tool with both hands.
•
Let the blade run freely for a few seconds before starting
the cut.
•
Apply only a gentle pressure to the tool while performing
the cut.
10
Wrench storage (Fig. L)
The spanner wrench (8) can be stored on the saw shoe as
shown in Fig. L.
Attaching and removing the rip fence (Fig. M)
The rip fence is used to saw in a straight line parallel to the
edge of the working piece.
Attaching
•
Loosen the locking knob (17).
•
Insert the rip fence (18) through the openings (19).
•
Slide the rip fence into the desired position.
(Original instructions)
•
Tighten the locking knob.
ENGLISH
Technical Data
Removing
Specifications
STSC1518
•
Loosen the locking knob.
Voltage
220-240V
•
Pull the rip fence out of the tool. Note: If you do not have
a proper fitting fence, use a straight edge guide in
contact with the edge of the shoe to improve accuracy of
cut and reduce the possibility of binding and kickback.
Frequency
50/60Hz
Power
1510W
Dust extraction
An adaptor is required to connect a vacuum cleaner or dust
extractor to the tool.
•
Insert the dust extraction adaptor into the saw dust
outlet (9).
•
Connect the vacuum cleaner hose to the adaptor.
Accessories
The performance of your tool depends on the accessory
used. Stanley and Piranha accessories are engineered to
high quality standards and designed to enhance the
performance of your tool. By using these accessories you
will get the very best from your tool.
Warning! The use of any accessory not
recommended for use with this tool could be
hazardous. Use only 185mm blades with 19mm
or 20mm diameter arbor.
Maintenance
Your tool has been designed to operate over a long period
of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
Warning! Before performing any maintenance,
switch off and unplug the tool.
•
Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
•
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Important! To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(other than those listed in this manual) should be
performed by authorized service centers or other
qualified service personnel, always using identical
replacement parts.
Lubrication
Stanley tools are properly lubricated at the factory and are
ready for use.
No-Load Speed
5500/min (rpm)
Maximum cutting depth
62mm AT 90°
46mm AT 45°
Service Information
STANLEY offers a full network of company-owned and
authorized service locations. All STANLEY Service Centers
are staffed with trained personnel to provide customers with
efficient and reliable power tool service. For more
information about our authorized service centers and if you
need technical advice, repair, or genuine factory
replacement parts, contact the STANLEY location nearest
you.
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Stanley product needs
replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for raw
materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Stanley provides a facility for the collection and recycling of
Stanley products once they have reached the end of their
working life. To take advantage of this service please return
your product to any authorised repair agent who will collect
them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Stanley office at the address
indicated in this manual. Alternatively, a list of authorised
Stanley repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com
11
ENGLISH
(Original instructions)
One year warranty
If your STANLEY product becomes defective due to faulty
materials or workmanship within 12 months from the date of
purchase, STANLEY guarantees to replace all defective
parts free of charge or – at our discretion – replace the unit
free of charge provided that:
•
The product has not been misused and has been used in
accordance with the instruction manual.
•
The product has been subject to fair wear and tear;
•
Repairs have not been attempted by unauthorised
•
Proof of purchase is produced.
•
The STANLEY product is returned complete with all
original components
If you wish to make a claim, contact your seller or check the
location of your nearest authorised STANLEY repair agent in
the STANLEY catalogue or contact your local STANLEY
office at the address indicated in this manual. A list of
authorised STANLEY repair agents and full details of our
after sales service is available on the internet
at:www.stanleytools.com
12
90618237
01/2015
Names & Addresses for STANLEY Service Concessionaries - MIDDLE EAST & AFRICA
ALGERIA: Sarl Outillage Corporation, 08 Rue Med Boudiaf - Cheraga - Algiers, Algeria. Tel: (213-21) 375130, Fax: (213-21) 369667. ANGOLA: Angoferraria,
Lda., Rua Robert Shields, No. 61, Luanda, Angola, Tel: 00244-222-395837 / 222-395034, Fax: 00244-222-394790. AZERBAIJAN: Royalton Holdings Ltd. 41
Khagani St. Apt. 47 AZ 1001, Baku. Tel: (994-12) 4935544, Fax: (994-12) 5980378. BAHRAIN: Kavalani & Sons W.L.L., P.O. Box 71, Sitra, Manama, Tel: (973)
17732888, Fax: (973) 17737379. Alfouz Services Co. WLL., P.O. Box 26562, Tubli, Manama. Tel: (973) 17783562, Fax: (973) 17783479. EGYPT: El Farab
S.A.E., 15-Nabil El Wakkad Street, Dokki, Giza, Egypt, Tel: 00202-37603946 / 002-010-2582544, Fax: 00202-33352796. ETHIOPIA: Seif Tewfik Sherif, Arada
Sub-City, Kebele 01/02, Global Insurance Building, 2nd Floor, Room 43, P.O. Box 2525, Addis Ababa, Ethiopia. Tel: (251-11) 1563968/ 1563969, Fax: (251-11)
1558009. IRAQ: Financial Links, Kazzaz Building Arasat Al-Hindia Block No: 629 Street: 31Building No: 1 Baghdad – Iraq. Tel: 00964 (0)780 195 2223/ 00964
(0)781 3763044. Al Sard Co. for General Trading Ltd. Jbara Bldg. 3Flr, Al Rasheed St. Bagdad. Tel: (964) 18184102. Sakhar Group, Arrassat al-hindya Al
Masbah, Bagdad. (964) 7400144446. JORDAN: Palestine Bldg. Matl. (Bashiti Hardware), 93 King Abdullah 2nd Street, Opp. ELBA House, P.O. Box 3005,
Amman 11953, Tel: (962-6) 5349098, Fax: (962-6) 5330731. KENYA: Dextron Tools Ltd., P.O. Box 20121-00200, Shariff House, Kimathi Street, Nairobi. Tel:
(254-20) 6905000/ 2358021, Fax: (254-20) 6905111/ 6905112. KUWAIT: Al Omar Technical Co., P.O. Box 4062, 13041 Safat, Kuwait. Tel: (965) 24848595/
24840039, Fax: (965) 24845652. Fawaz Al Zayani Establishment, P.O. Box 42426, Shop No. 18, Al Humaizi Commercial Complex, Khalifa Al Jassim,
Shuwaikh, Kuwait. Tel: (965) 24828710, Fax: (965) 24828716. Fawaz Al Zayani Establishment, P.O. Box 42426, Shop No.18, Al Humaizi Commercial
Complex, Khalifa Al Jassim, Shuwaikh, Kuwait, Tel: (965) 24828710, Fax: (965) 24828716. Fawaz Al Zayani Establishment, Fahaheel Industrial Area, Main St.,
Sanaya, Kuwait, Tel: (965) 23925830, Fax: (965) 24828716. LEBANON: Est. Shaya & Azar S.A.R.L., Boulvard Jdeideh - Mar Takla - Bouchrieh .P.O. Box
90545 Jdeideh.Beirut - Lebanon, Tel: 00961 1 872305 / 306 , Fax: 00961 1 872303. LIBYA: North Africa Trading ( El Ghoul Brothers), AlHilal Service Center
Tawergha St. Misurata, Tel: 00218-091-3221408. (Benghazi) Sniydel st., Amr Ibn EL-Aas Rd. Tel: (+218) 92 5771120. (Tripoli) Al Barniq Service Center,
Mokhazin elsukar st., ElFallah. Tel: (+218) 21 4808019. (Misrata) Al Hilal Service Center, Tawergha st. Tel: (+218) 51 2626743. MAURITIUS: Robert Le Marie
Limited, Old Moka Road, Bell Village, P.O. Box 161, Port Louis, Tel: 00230-212 1865/ 212 2847, Fax: 00230-2080843. MOROCCO: Ets Louis Guillaud & Cie,
149, Quartier Industriel, Moulay Rachid, Casablanca, Postal Code 20450, Morocco, Tel: 00212-522729233, Fax: 00212-522729096. NIGERIA: Meridian
Power Tools Ltd., Gr.Floor, #1 Alhaji Masha Rd, Next toTeslim Balogun Stadium, Near National Stadium Surulere, Lagos, Nigeria, Tel: 00234-1-7740431 /
7740410, Fax: 00234-1-7913798. OMAN: Al Jizzi Company LLC, P.O. Box 1704,PC 112 Ruwi, Oman, Tel: (968) 24832618/ 24835153, Fax: (968)
24831334/24836460. Al Hassan Technical & Construction Supplies Co. LLC, P.O. Box 1948, P.C. 112, Ruwi, Tel: (968) 24810575 / 24837054, Fax: (968)
24810287/ 24833080. Oman Hardware Co. LLC, P.O. Box 635, Ruwi Postal Code 112, Te: (968) 24815131, Fax: (968) 24816491. Khimji Ramdas, P.O. Box
19, Post Code 100, Ghala, Muscat, Oman. Tel: (968) 24595906/ 907, Fax: (968) 24852752. Oman Marketing & Service Co. (Omasco), P.O. Box 2734, Behind
Honda Showroom, Wattayah, Oman. Tel: (968) 24560232/ 24560255, Fax: (968) 24560993. Oman Marketing & Service Co. (Omasco), Al Ohi, Sohar, Oman.
Tel: (968) 26846379, Fax: (968) 26846379. Oman Marketing & Service Co. (Omasco), Sanaya, Salalah, Oman. Tel: (968) 23212290, Fax: (968) 23210936.
PAKISTAN: ZIT Co - Nasir & Bros., 2nd Floor, Qadri Center, Chowk Dalgran Railway Road, Lahore, Pakistan, Tel: 0092 42 37670839, Fax: 0092 42
37652989. Ammar Service & Spares, 60-Bank Arcade, Serai Road, Karachi, Pakistan. Tel: (92-21) 32426905, Fax: (92-21) 32427214. QATAR: Teyseer
Industrial Supplies & Services Co. WLL, 55, Al Wakalat St. (Between St. 18 & 19) Salwa Industrial Area, P.O. Box 40523 Doha,Qatar, Te: (974) 44581536, Fax:
(974) 44682024. Shaheen Electrical Works & Trading Co. WLL, Gate 34, St. 44 Industrial Area P.O. Box 9756, Doha, Tel: (974) 44600230 /44600525, Fax:
(974) 44601338. Al Muftah Service Centre, Al Wakrah Road, P.O. Box 875, Doha,Qatar, Tel: (974) 44650880/ 44650110/ 44446868, Fax: (974) 44441415 /
44662599. SAUDI ARABIA: (Al Bahr) Mohamed Ahmed Bin Afif Est., P.O. Box 530, Yanbu, Al Bahr. Tel: (966-4) 3222626/ 3228867, Fax: (966-4) 3222210.
(Al Khobar) Fawaz Ebrahim Al Zayani Trading Est., P.O. Box 76026, Al Khobar # 31952, Tel: (966-3) 8140914, Fax: (966-3) 8140824. MSS (Al-Mojil Supply &
Services) P.O. Box 450, Jubail 31951, Opp. Gulf Bridge Library & Riyadh House. Tel: (966-3) 3612850/ 3624487/ 3621729, Fax: (966-3) 3623589/ 3620783.
(Dammam) MSS (Al-Mojil Supply & Services), P.O. Box 450, Jubail 31951.Opp-Gulf Bridge Library & Riyadh House, Tel: (966-3) 3612850 / 3624487 /
3621729, Fax: (966-3) 3623589 / 3620783. Al Bawardi Tools & Hardware, P.O. Box 112, Dammam, Tel: (966-3) 8330780 Ext.24 / 8348585 Ext. 24 /
+966-3-8335555, Fax: (966-3) 8336303. (Al Hassa) Mutawa Trading & Gen. Services, Maliki road Hafuf city, Al Hassa, KSA. Tel: (966) 502846275 (Jeddah) Al
Bawardi Tools & Hardware, P.O. Box 16905, Jeddah 21474, Tel: (966-2) 6444547 / 6439035 / 6456095, Fax: (966-2) 6439024. EAC (Al Yousef Contg. & Trdg.
Est.), P.O. Box 30377, Jeddah -21477, Tel: (966-2) 6519912, Fax: (966-2) 6511153. (Madina) Garziz Trading for Bldg Mat & Decoration, P.O. Box 3364,
Madina, Tel: (966-4) 826 14 90 / 8227636, Fax: (966-4) 8265741. (Riyadh) Industrial Material Organization (IMO), P.O. Box 623, Rail Street ,Riyadh, Tel:
(966-1) 4028010 Ext 26 / 8001245757, Fax: (966-1) 4037970. Sultan Garment Factory (RSC), P.O. Box 29912, Riyadh 11467, KSA, Tel: (966-1) 4055148 /
4042889, Fax: (966-1) 4055148. Al Bawardi Tools & Hardware, P.O. Box 68, Riyadh 11411, Tel: (966-1) 4484999, Fax: (966-1) 4487877. (Yanbu) Fawaz
Ebrahim Al Zayani, Opposite to Al Fouzan, Jeddah highway or King Abdul Aziz road, Yanbu. Tel: (966-4) 3960980, Fax: (966-4) 3961980. Mohamed Ahmed
Bin Afif Est., P.O. Box 530, Yanbu, Al Bahr, Tel: (966-4) 3222626/ 3228867, Fax: (966-4) 3222210. SOUTH AFRICA: Stanley Black & Decker - RSA, 199
Winze Drive Stormill Ext 9 Roodepoort, Tel: (2711) 472 0454, Fax: (2711) 472 0482. Trevco Power Tool Service 14 Steenbok Street, Koedoespoort, 0186,
Pretoria, South Africa. Tel: (27-86) 1873826, Fax: (27-86) 5001771. TANZANIA: General Motors investment Ltd., P.O. Box 16541, 14 Nyerere Road,
Vingunguti, Dar-es-Salaam. Tel: (255 22) 2862661/ 2865022, Fax: (255 22) 2862667. TUNISIA: Societe Tunisienne De Maintenance (STM), Rue de la
Physique. Nouvelle Zone Industrielle Ben Arous., 2013 Ben Arous, Tunisia. Tel: (+216) 79 389687, Fax: (+216) 71 385154. UAE: (Abu Dhabi) Light House
Electrical, P.O. Box 120, Abu Dhabi, Tel: (971-2) 6726131, Fax: (971-2) 6720667. Galaxy Equipment Trading, Madinath Zayed (Baada Zaid), Abu Dhabi P.C.
58910, Tel: (971-2) 8844279, Fax: (971-2) 8844297 (Ajman) Al Sukoon Gen. Trdg. Co. LLC, P.O. Box 2975, Ajman. Tel: (971-6) 7435725/ 7438317, Fax:
(971-6) 7437350. Al Sukoon Gen. Trdg. Co. LLC, P.O. Box 2975, Ajman, Tel: (971-6) 7435725 / 7438317, Fax: (971-6) 7437350 (Al Ain) Zillion Equipment and
Spare Parts Trading LLC, P.O. Box 19740, Opp. Bin Sadal/ Trimix Redymix Sanaiya, Al Ain. Tel: (971-3) 7216690, Fax: (971-3) 7216103. (Dubai) Black &
Decker (Overseas) GmbH, P.O. Box 5420, Dubai, Tel: (971-4) 8127400/ 8127406, Fax: (971-4)2822765. Ideal Star Workshop Eqpt.Trading LLC, P.O. Box
37116, Al Quoz, Dubai, Tel: (971-4) 3474160, Fax: (971-4) 3474157, Fine Tools, P.O.Box 30139 , Al Quoz, Dubai, Tel: (971-4) 3385240, Fax: (971-4) 3385239,
Alebrah Engineering Service, P.O. Box 78954, Al Qusais , Dubai, Tel: (971-4) 2850044, Fax: (971-4) 2844802. (Musaffah) Light House Electrical, P.O. Box
120, Abu Dhabi, Tel: (971-2) 5548315, Fax: (971-2) 5540461. (Sharjah) Mc Coy Middle East LLC, P.O. Box 25793, Sharjah, Tel: (971-6) 5395931, Fax:
(971-6) 5395932. Burj Al Madeena, Industrial Area No.1, Opp. Pakistani Masjid, P.O. Box 37635, Sharjah. Tel: (971-6) 5337747, Fax: (971-6) 5337719. Burj Al
Madeena, , Industrial Area No 1,opp Pakistani Masjid P.O. Box 37635, Sharjah, Tel: (971-6) 5337747, Fax: (971-6) 5337719 (Ras Al Khaimah) Mc Coy Middle
East LLC, P.O. Box 10584, Ras Al Khaimah, Tel: (971-7) 2277095, Fax: (971-7) 2277096. UGANDA: The Building Center (U) Ltd., 52 Station Road, Kitgum
House, P.O. Box 7436, Kampala, Uganda. Tel: (256-41) 4234567/ 4259754, Fax: (256-41) 4236413. YEMEN: (Aden) Middle East Trad. Co. Ltd. (METCO),
Mualla Dakka, Aden, Yemen. Tel: (967-2) 222670, Fax: (967-2) 222670. (Sana'a) Middle East Trad. Co. Ltd. (METCO), Hayel St., Sana'a, Yemen. Tel: (967-1)
204201, Fax: (967-1) 204204. (Taiz) Middle East Trading Co. (METCO), P.O. Box 12363, 5th Flr, Hayel Saeed Anam Bldg, Al-Mugamma St. Taiz, Yemen. Tel:
(967-4) 213455, Fax: (967-4) 219869.
Download PDF

advertising