STDR5206 | Stanley STDR5206 SCREWDRIVER instruction manual

Stanley STDR5206 SCREWDRIVER instruction manual
STDR5206
English
French
Portuguese
Russian
Ukrainian
Arabic
Page
Page
Page
Page
Page
Page
3
7
11
15
24
31
(Original instructions)
ENGLISH
FIG. A
3
1
2
6
4
5
FIG. B
FIG. C
4
5
5
FIG. D
FIG. E
7
5
6
2
8
1
(Original instructions)
FIG. F
2
7
ENGLISH
FIG. G
8
9
2
1
10
FIG. H
FIG. I
FIG. J
FIG. K
2
1
3
ENGLISH
(Original instructions)
DO NOT RETURN THIS PRODUCT TO THE STORE,
first contact your local STANLEY Office
or nearest authorized service center.
General Safety Rules
Warning! Read and understand all instructions.
Failure to follow all instructions listed below, may
result in electric shock, fire and/or serious
personal injury.
Save These Instructions
Safety instructions
General power tool safety warnings
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below
refers to your mains operated (corded) power tool or battery
operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose
control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk
of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
4
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric
shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock. Note: The term “Residual Curent Device
(RCD)” can be replaced by “Ground Fault Circuit
Interrupter (GFCI)” or by “Earth Leakage Circuit Breaker
(ELCB)”.
3. Personal safety
a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is
in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch on
invites accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
e. Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
(Original instructions)
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
6. Labels on tool
The label on your tool may include the following symbols:
Read
Instructions
Manual
4. Power tool use and care
Use Eye
Protection
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
ENGLISH
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
Use Ear
Protection
V ........ Volts
A ........ Amperes
..... Direct
Current
Earthing
Terminal
....
Safety Alert
Symbol
.../min..
Revolutions
or Reciprocation per
minute
Position of date barcode
The Date Code, which also includes the year of
manufacture, is printed into the housing.
Example:
2014 XX JN
Year of manufacturing
7. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main
voltage corresponds to the voltage on the rating
plate.
Warning! If the power cord is damaged, it must be
replaced by the manufacturer, authorized
STANLEY Service Center or an equally qualified person in
order to avoid damage or injury. If the power cord is replaced
by an equally qualified person, but not authorized by
STANLEY, the warranty will not be valid.
Features (Fig. A)
1. Depth stop
2. Depth adjuster
3. Belt clip
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is
maintained.
4. Forward/Reverse switch
Hold power tool by insulated gripping surfaces, when
performing an operation where the fastener may
contact hidden wiring or its own cord. Fasteners
contacting a "live" wire may make exposed metal parts of
the power tool "live" and could give the operator an electric
shock.
....
n 0 ....... No-Load
Speed
5. Service
Screwdriver safety warnings
...... Class II
Construction
5. Variable speed trigger switch
6. Lock-on button
Specific Safety Rules
Warning! Know your drywall screwdriver. Do not
plug the tool into the power source until you have
read and understand this Instruction Manual.
Learn the tool’s applications and limitations, as
well as the specific potential hazards related to this tool.
•
Following this rule will reduce the risk of electric shock,
fire, or serious injury.
5
ENGLISH
•
(Original instructions)
Always wear eye protection. Any power tool can throw
foreign objects into your eyes and cause permanent eye
damage. ALWAYS wear safety goggles (not glasses) that
comply with ANSI safety standard Z87.1. Everyday
glasses have only impact resistant lenses. They ARE
NOT safety glasses
Warning! Glasses or goggles not in compliance
with ANSI Z87.1 could cause serious injury when
they break.
•
Never use the drywall screwdriver to drive screws other
than drywall screws. The drywall screwdriver and the
screwdriver bits are designed specifically for driving
drywall screws.
•
Only use screwdriver bits that are designed for use with
this tool.
•
Always keep hands out of the path of the drywall screw.
Avoid awkward hand positions where a sudden slip could
cause your hand to move into the path of the saw blade.
•
Make sure there are no nails or foreign objects in the
part of the workpiece to be cut or sanded.
•
To avoid injury from accidental starting, always remove
the plug from the power source before installing or
removing a screwdriver bit or when adjusting the depth
control.
•
Always check the wall area where screws will be driven
to be sure there are no hidden electrical wires in the
area.
•
Never leave the Lock-on button ON. Before plugging the
tool into the power source, make sure the lock-on button
is OFF.
General Safety Warnings
Warning! Wear a dust mask that is designed to be
used when operating a power tool in a dusty
environment.
Warning! Dust that is created by power sanding,
sawing, grinding, drilling, and other construction
activities may contain chemicals that are known to
cause cancer, birth defects, or other genetic abnormalities.
These chemicals include:
•
Lead from lead-based paints
•
Crystalline silica from bricks, cement, and other masonry
products
•
Arsenic and chromium from chemically treate lumber
6
The level of risk from exposure to these chemicals varies,
according to how often this type of work is performed. In
order to reduce exposure to these chemicals, work in a
well-ventilated area, and use approved safety equipment,
such as a dust mask that is specifically designed to filter out
microscopic particles.
Safety Extension Cord
Warning! Keep the extension cord clear of the
working area. Position the cord so it will not get
caught on the workpiece, tools or any other obstructions
while you are working with the power tool.
Make sure any extension cord used with this tool is in good
condition. When using an extension cord, be sure to use one
of heavy enough gauge to carry the current the tool will
draw. An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating.
Be sure your extension cord is properly wired and in good
condition. Always replace a damaged extension cord or
have it repaired by a qualified electrician before using it.
Protect your extension cord from sharp objects, excessive
heat and damp or wet areas.
Use a separate electrical circuit for your power tools. This
circuit must not be less than 14 gauge wire and should be
protected with either a 15 A time delayed fuse or circuit
breaker. Before connecting the power tool to the power
source, make sure the switch is in the OFF position and the
power source is the same as indicated on the nameplate.
Running at lower voltage will damage the motor.
Contents
Carefully unpack the drywall screwdriver. Compare the
contents against the “Drywall screwdriver components” chart
below.
Assembly and Operating
Warning! To avoid fire or toxic reaction, never use
gasoline, naphtha, acetone, lacquer thinner or
similar highly volatile solvents to clean the tool.
Forward/Reverse switch (Fig. B)
The forward/reverse switch (4) is conveniently mounted in
front of the variable speed trigger switch (5). To make the
screwdriver rotate clockwise for driving screws, push the
forward/reverse switch (4) to the left. To make the
screwdriver rotate counter-clockwise to remove screws,
push the forward/reverse switch (4) to the right.
(Original instructions)
ENGLISH
Notes:
Notes:
a. Never change the position of the forward/reverse switch
(4) while the screwdriver bit is turning.
a. Use only 1” (25 mm) long bits that are designed for use
in driving drywall screws.
b. The variable speed trigger switch (5) will NOT function
with the forward/reverse switch (4) in the middle
position.
b. Make sure the bit size is correct for the drywall screws
being driven. This will usually be a #2 size.
Variable speed trigger switch (Fig. C)
This screwdriver is equipped with a variable speed On/Off
trigger switch.
1. To start screwdriver, gently squeeze the variable speed
trigger switch (5).
Note: The screwdriver will turn at its slowest speed when
the variable speed trigger switch is depressed slightly. The
screwdriver will turn at its fastest speed when the variable
speed trigger switch is fully depressed.
2. To stop the screwdriver, release the variable speed
trigger switch (5).
Replacing the magnetic bit holder (Fig. F)
If the magnetic bit holder becomes worn or damaged, it must
be replaced. The replacement bit holder must be of the
same dimensions as the original and have the ANSI
retention groove on the end that is inserted into the tool.
1. Remove the nosepiece (2) by turning it counter
clockwise.
Note: Do not use pliers on the nosepiece. Only use your
hand.
2. Grasp the screwdriver bit (7) with pliers and pull it out of
the magnetic bit holder (8).
Lock-on button (Fig. D)
3. Grasp the large end of the bit holder with pliers and pull
it straight out of the screwdriver spindle (9).
The lock-on button feature allows the trigger switch to be
locked in the ON position at full speed when continuous
operation for extended periods of time is required.
4. Reverse the process by inserting the replacement
magnetic bit holder into the tool.
To lock the lock-on button in the ON position, pull back on
the variable speed trigger switch (5) to start the screwdriver
and push the lock-on button (6) into the screwdriver handle.
Release the variable speed trigger switch while holding the
lock-on button into the screwdriver handle. The screwdriver
will continue to run. To release the lock-on button, pull
variable speed trigger switch back (5) and then release the
trigger.
Note: Operating the screwdriver with the variable speed
trigger switch for an extended period of time may cause the
screwdriver motor to overheat. If the screwdriver gets hot,
stop driving screws and allow it to cool for at least 15
minutes.
Inserting a screwdriver bit (Fig. E)
This tool has a magnetic bit holder that provides convenient
bit changes. To install a bit, simply insert the hex bit shank
(7) into the magnetic bit holder (8) that is located inside the
depth stop (1). Push the bit into the magnetic bit holder until
the magnet holds the bit in place.
Note: When inserting the replacement for magnetic bit
holder, gently tap it into place to make sure it is fully inserted.
Grasp the large end of the magnetic bit holder to ensure the
retention groove (10) is holding the magnetic bit holder in
place in the tool.
5. Reinstall the screwdriver bit and nose piece.
Safety Recommendations
Check the following every time you use the screwdriver:
1. Wear safety glasses or a mask.
2. Use hearing protection.
3. The screwdriver tip is the right size and it is in good
condition.
4. No power cables “live” where you are inserting the
screws.
Note: Failure to follow these safety rules will significantly
increase the risk of injury.
7
ENGLISH
(Original instructions)
Adjusting the screwdrive bit depth (Fig. G)
It is important to control the depth to which the drywall screw
will be driven. Over driving the screw will drive the screw too
deep and break the outer paper layer of the drywall. Under
driving the screw will leave the screw head above the
drywall surface making it impossible to properly finish the
drywall.
This will provide better control over the tool help
eliminate screws being driven at an angle.
•
Place the drywall screw on the screwdriver bit. The
magnetic bit holder will hold any steel screw for easy
starting.
•
Press the screw against the drywall with steady even
pressure and squeeze the variable speed trigger switch.
The clutch in the tool will engage and the screw will be
driven to the preset depth. Once fully driven, the clutch
will make a chattering sound until the variable speed
trigger is released.
•
When the screw is properly driven, the screw head will
be slightly countersunk into the drywall without breaking
the outer drywall paper. At this point, the clutch will
release to prevent over driving the screw. This will result
in minimum work to fill the holes and taping the seams.
•
The belt clip allows you to conveniently attached the
screwdriver to your belt. This will allow you to use both
hands for positioning the drywall.
The depth control system is made up of the depth stop (1)
and the depth adjuster (2).
Warning! The following adjustments should always
be verified using a scrap piece of drywall to avoid
damaging the “good” drywall sections.
1. Rotate the depth adjuster counter clockwise until
approximately 1/4” of the screwdriver bit extends beyond
the depth stop.
2. Place a drywall screw onto the screwdriver bit. The
magnetized bit will hold the screw onto the bit.
Note: Before driving the screw, press the screw point into
the drywall and make sure the screw is perpendicular to the
drywall.
3. Press the screw against the drywall with steady even
pressure and squeeze the trigger switch. The clutch in
the tool will engage and the screw will be driven to the
preset depth.
4. If the screw is not driven deep enough, the head of the
screw will not be recessed into the drywall (Fig. H). In
this case, turn the depth adjustment sleeve clockwise
until the correct depth has been achieved. If the screw is
driven too deep, it will be recessed too far into the
drywall and the outer paper of the drywall will be
fractured (Fig. I). In this case, turn the depth adjustment
sleeve counter clockwise until the correct depth has
been achieved. Fig. J illustrates the correct depth for the
screw to be driven.
Note: For each revolution the depth adjustment sleeve is
rotated, the depth will increase/decrease approximately
1/16” (1.6 mm).
Tips for driving drywall screws
ff Always drive the screws perpendicular to the drywall so
the heads are properly countersunk. They should never be
driven at an angle.
•
Support the tool with both hands wherever possible.
8
Removing drywall screws (Fig. K)
To remove drywall screws, remove the depth stop (1) to
expose the screwdriver bit.
Notes:
a. The depth stop is a press fit onto the depth adjuster (2).
Simply twist and pull outward to slide it off the depth
adjuster.
b. You can also turn the depth adjuster clockwise to expose
the screwdriver bit. This however will cause you to lose
the depth setting and you will have to re-set the depth.
Maintenance
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up of
metal dust can cause tracking of electrical current from the
internal parts to exposed metal parts. Do not overload your
angle grinder. Overloading causes a reduction in speed and
efficiency, causing your angle grinder to become too hot. If
this happens, operate your angle grinder under no load for
one or two minutes until it has cooled to normal operating
temperature. Switching your angle grinder off under load will
reduce the life of the switch.
(Original instructions)
Warning! When servicing, use only identical
replacement parts. The use of any other part may
create a hazard or cause product damage.
•
DO NOT use solvents when cleaning plastic parts.
Plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use a clean cloth to remove dirt, dust, oil, grease etc.
Warning! Do not allow brake fluids, gasoline,
petroleum-based products, penetrating oils, etc. to
come into contact with plastic parts. They contain chemicals
that can damage, weaken or destroy plastic.
•
Remove accumulated dust and debris regularly using a
SOFT and DRY brush.
Warning! Use safety goggles when using an air jet
to blow dust out of the tool. Keep air vents clean
and unobstructed to allow maximum airflow through the tool.
•
DO NOT abuse power tools. Abusive practices can
damage the tool and the workpiece.
Warning! DO NOT attempt to modify tools or
create accessories. Any such alteration or
modification is misuse and could result in a hazardous
condition leading to possible serious injury. It will also void
the warranty.
ENGLISH
Specifications
STDR5206
Power
520W
Voltage
220-240V
Frequency
50/60Hz
No-load speed
4500/min (rpm)
Weight
3.3lb (1.45kg)
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Stanley product needs
replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for raw
materials.
Cleaning
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Stanley provides a facility for the collection and recycling of
Stanley products once they have reached the end of their
working life. To take advantage of this service please return
your product to any authorised repair agent who will collect
them on our behalf.
Use only mild soap and a slightly damp cloth to clean your
angle grinder. Many household cleaners contain chemicals
which could seriously damage the plastic. Also, do not use
petrol, turpentine, lacquer or paint thinners or similar
products. Never let any liquid get inside the tool and never
immerse any part of the tool into liquid.
You can check the location of your nearest authorised repair
agent by contacting your local Stanley office at the address
indicated in this manual. Alternatively, a list of authorised
Stanley repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com
Lubrication
All of the bearings in this tool are lubricated with a sufficient
amount of high-grade lubricant for the life of the unit under
normal conditions. Therefore, no further lubrication is
required.
Important! To assure product SAFETY and
RELIABILITY, repairs, maintenance and
adjustment (other than those listed in this manual) should be
performed by authorized service centers or other qualified
service personnel, always using identical replacement parts.
9
ENGLISH
(Original instructions)
EC declaration of conformity
MACHINERY DIRECTIVE
STDR5206
STANLEY declares that these products described under
"technical data" are in compliance with:
2006/42/EC, EN 60745-1, EN60745-2-2
These products also comply with Directive
2014/30/EU and 2011/65/EU. For more information, please
contact STANLEY at the following address or refer to the
back of the manual.
The undersigned is responsible for compilation of the
technical file and makes this declaration on behalf of
STANLEY.
R.Laverick
Engineering Manager
STANLEY , Europe, Egide Walschaertsstraat14-18,
2800 Mechelen, Belgium
12.2014
10
Guarantee
STANLEY Europe is confident of the quality of its products
and offers an outstanding guarantee for professional users of
the product. This guarantee statement is in addition to and in
no way prejudices your contractual rights as a private
non-professional user. The guarantee is valid within the
territories of the Member States of the European Union and
the European Free Trade Area.
One year full warranty
If your STANLEY product becomes defective due to faulty
materials or workmanship within 12 months from the date of
purchase, STANLEY Europe guarantees to replace all
defective parts free of charge or – at our discretion – replace
the unit free of charge provided that:
•
The product has not been misused and has been used in
accordance with the instruction manual.
•
The product has been subject to fair wear and tear;
•
Repairs have not been attempted by unauthorised
persons;
•
Proof of purchase is produced.
•
The STANLEY product is returned complete with all
original components
If you wish to make a claim, contact your seller or check the
location of your nearest authorised STANLEY repair agent in
the STANLEY catalogue or contact your local STANLEY
office at the address indicated in this manual. A list of
authorised STANLEY repair agents and full details of our
after sales service is available on the internet
at:www.stanleytools.com
Names & Addresses for STANLEY Service Concessionaries - MIDDLE EAST & AFRICA
ALGERIA: Sarl Outillage Corporation, 08 Rue Med Boudiaf - Cheraga - Algiers, Algeria. Tel: (213-21) 375130, Fax: (213-21) 369667. ANGOLA: Angoferraria,
Lda., Rua Robert Shields, No. 61, Luanda, Angola, Tel: 00244-222-395837 / 222-395034, Fax: 00244-222-394790. AZERBAIJAN: Royalton Holdings Ltd. 41
Khagani St. Apt. 47 AZ 1001, Baku. Tel: (994-12) 4935544, Fax: (994-12) 5980378. BAHRAIN: Kavalani & Sons W.L.L., P.O. Box 71, Sitra, Manama, Tel: (973)
17732888, Fax: (973) 17737379. Alfouz Services Co. WLL., P.O. Box 26562, Tubli, Manama. Tel: (973) 17783562, Fax: (973) 17783479. EGYPT: El Farab
S.A.E., 15-Nabil El Wakkad Street, Dokki, Giza, Egypt, Tel: 00202-37603946 / 002-010-2582544, Fax: 00202-33352796. ETHIOPIA: Seif Tewfik Sherif, Arada
Sub-City, Kebele 01/02, Global Insurance Building, 2nd Floor, Room 43, P.O. Box 2525, Addis Ababa, Ethiopia. Tel: (251-11) 1563968/ 1563969, Fax: (251-11)
1558009. IRAQ: Financial Links, Kazzaz Building Arasat Al-Hindia Block No: 629 Street: 31Building No: 1 Baghdad – Iraq. Tel: 00964 (0)780 195 2223/ 00964
(0)781 3763044. Al Sard Co. for General Trading Ltd. Jbara Bldg. 3Flr, Al Rasheed St. Bagdad. Tel: (964) 18184102. Sakhar Group, Arrassat al-hindya Al
Masbah, Bagdad. (964) 7400144446. JORDAN: Palestine Bldg. Matl. (Bashiti Hardware), 93 King Abdullah 2nd Street, Opp. ELBA House, P.O. Box 3005,
Amman 11953, Tel: (962-6) 5349098, Fax: (962-6) 5330731. KENYA: Dextron Tools Ltd., P.O. Box 20121-00200, Shariff House, Kimathi Street, Nairobi. Tel:
(254-20) 6905000/ 2358021, Fax: (254-20) 6905111/ 6905112. KUWAIT: Al Omar Technical Co., P.O. Box 4062, 13041 Safat, Kuwait. Tel: (965) 24848595/
24840039, Fax: (965) 24845652. Fawaz Al Zayani Establishment, P.O. Box 42426, Shop No. 18, Al Humaizi Commercial Complex, Khalifa Al Jassim,
Shuwaikh, Kuwait. Tel: (965) 24828710, Fax: (965) 24828716. Fawaz Al Zayani Establishment, P.O. Box 42426, Shop No.18, Al Humaizi Commercial
Complex, Khalifa Al Jassim, Shuwaikh, Kuwait, Tel: (965) 24828710, Fax: (965) 24828716. Fawaz Al Zayani Establishment, Fahaheel Industrial Area, Main St.,
Sanaya, Kuwait, Tel: (965) 23925830, Fax: (965) 24828716. LEBANON: Est. Shaya & Azar S.A.R.L., Boulvard Jdeideh - Mar Takla - Bouchrieh .P.O. Box
90545 Jdeideh.Beirut - Lebanon, Tel: 00961 1 872305 / 306 , Fax: 00961 1 872303. LIBYA: North Africa Trading ( El Ghoul Brothers), AlHilal Service Center
Tawergha St. Misurata, Tel: 00218-091-3221408. (Benghazi) Sniydel st., Amr Ibn EL-Aas Rd. Tel: (+218) 92 5771120. (Tripoli) Al Barniq Service Center,
Mokhazin elsukar st., ElFallah. Tel: (+218) 21 4808019. (Misrata) Al Hilal Service Center, Tawergha st. Tel: (+218) 51 2626743. MAURITIUS: Robert Le Marie
Limited, Old Moka Road, Bell Village, P.O. Box 161, Port Louis, Tel: 00230-212 1865/ 212 2847, Fax: 00230-2080843. MOROCCO: Ets Louis Guillaud & Cie,
149, Quartier Industriel, Moulay Rachid, Casablanca, Postal Code 20450, Morocco, Tel: 00212-522729233, Fax: 00212-522729096. NIGERIA: Meridian
Power Tools Ltd., Gr.Floor, #1 Alhaji Masha Rd, Next toTeslim Balogun Stadium, Near National Stadium Surulere, Lagos, Nigeria, Tel: 00234-1-7740431 /
7740410, Fax: 00234-1-7913798. OMAN: Al Jizzi Company LLC, P.O. Box 1704,PC 112 Ruwi, Oman, Tel: (968) 24832618/ 24835153, Fax: (968)
24831334/24836460. Al Hassan Technical & Construction Supplies Co. LLC, P.O. Box 1948, P.C. 112, Ruwi, Tel: (968) 24810575 / 24837054, Fax: (968)
24810287/ 24833080. Oman Hardware Co. LLC, P.O. Box 635, Ruwi Postal Code 112, Te: (968) 24815131, Fax: (968) 24816491. Khimji Ramdas, P.O. Box
19, Post Code 100, Ghala, Muscat, Oman. Tel: (968) 24595906/ 907, Fax: (968) 24852752. Oman Marketing & Service Co. (Omasco), P.O. Box 2734, Behind
Honda Showroom, Wattayah, Oman. Tel: (968) 24560232/ 24560255, Fax: (968) 24560993. Oman Marketing & Service Co. (Omasco), Al Ohi, Sohar, Oman.
Tel: (968) 26846379, Fax: (968) 26846379. Oman Marketing & Service Co. (Omasco), Sanaya, Salalah, Oman. Tel: (968) 23212290, Fax: (968) 23210936.
PAKISTAN: ZIT Co - Nasir & Bros., 2nd Floor, Qadri Center, Chowk Dalgran Railway Road, Lahore, Pakistan, Tel: 0092 42 37670839, Fax: 0092 42
37652989. Ammar Service & Spares, 60-Bank Arcade, Serai Road, Karachi, Pakistan. Tel: (92-21) 32426905, Fax: (92-21) 32427214. QATAR: Teyseer
Industrial Supplies & Services Co. WLL, 55, Al Wakalat St. (Between St. 18 & 19) Salwa Industrial Area, P.O. Box 40523 Doha,Qatar, Te: (974) 44581536, Fax:
(974) 44682024. Shaheen Electrical Works & Trading Co. WLL, Gate 34, St. 44 Industrial Area P.O. Box 9756, Doha, Tel: (974) 44600230 /44600525, Fax:
(974) 44601338. Al Muftah Service Centre, Al Wakrah Road, P.O. Box 875, Doha,Qatar, Tel: (974) 44650880/ 44650110/ 44446868, Fax: (974) 44441415 /
44662599. SAUDI ARABIA: (Al Bahr) Mohamed Ahmed Bin Afif Est., P.O. Box 530, Yanbu, Al Bahr. Tel: (966-4) 3222626/ 3228867, Fax: (966-4) 3222210.
(Al Khobar) Fawaz Ebrahim Al Zayani Trading Est., P.O. Box 76026, Al Khobar # 31952, Tel: (966-3) 8140914, Fax: (966-3) 8140824. MSS (Al-Mojil Supply &
Services) P.O. Box 450, Jubail 31951, Opp. Gulf Bridge Library & Riyadh House. Tel: (966-3) 3612850/ 3624487/ 3621729, Fax: (966-3) 3623589/ 3620783.
(Dammam) MSS (Al-Mojil Supply & Services), P.O. Box 450, Jubail 31951.Opp-Gulf Bridge Library & Riyadh House, Tel: (966-3) 3612850 / 3624487 /
3621729, Fax: (966-3) 3623589 / 3620783. Al Bawardi Tools & Hardware, P.O. Box 112, Dammam, Tel: (966-3) 8330780 Ext.24 / 8348585 Ext. 24 /
+966-3-8335555, Fax: (966-3) 8336303. (Al Hassa) Mutawa Trading & Gen. Services, Maliki road Hafuf city, Al Hassa, KSA. Tel: (966) 502846275 (Jeddah) Al
Bawardi Tools & Hardware, P.O. Box 16905, Jeddah 21474, Tel: (966-2) 6444547 / 6439035 / 6456095, Fax: (966-2) 6439024. EAC (Al Yousef Contg. & Trdg.
Est.), P.O. Box 30377, Jeddah -21477, Tel: (966-2) 6519912, Fax: (966-2) 6511153. (Madina) Garziz Trading for Bldg Mat & Decoration, P.O. Box 3364,
Madina, Tel: (966-4) 826 14 90 / 8227636, Fax: (966-4) 8265741. (Riyadh) Industrial Material Organization (IMO), P.O. Box 623, Rail Street ,Riyadh, Tel:
(966-1) 4028010 Ext 26 / 8001245757, Fax: (966-1) 4037970. Sultan Garment Factory (RSC), P.O. Box 29912, Riyadh 11467, KSA, Tel: (966-1) 4055148 /
4042889, Fax: (966-1) 4055148. Al Bawardi Tools & Hardware, P.O. Box 68, Riyadh 11411, Tel: (966-1) 4484999, Fax: (966-1) 4487877. (Yanbu) Fawaz
Ebrahim Al Zayani, Opposite to Al Fouzan, Jeddah highway or King Abdul Aziz road, Yanbu. Tel: (966-4) 3960980, Fax: (966-4) 3961980. Mohamed Ahmed
Bin Afif Est., P.O. Box 530, Yanbu, Al Bahr, Tel: (966-4) 3222626/ 3228867, Fax: (966-4) 3222210. SOUTH AFRICA: Stanley Black & Decker - RSA, 199
Winze Drive Stormill Ext 9 Roodepoort, Tel: (2711) 472 0454, Fax: (2711) 472 0482. Trevco Power Tool Service 14 Steenbok Street, Koedoespoort, 0186,
Pretoria, South Africa. Tel: (27-86) 1873826, Fax: (27-86) 5001771. TANZANIA: General Motors investment Ltd., P.O. Box 16541, 14 Nyerere Road,
Vingunguti, Dar-es-Salaam. Tel: (255 22) 2862661/ 2865022, Fax: (255 22) 2862667. TUNISIA: Societe Tunisienne De Maintenance (STM), Rue de la
Physique. Nouvelle Zone Industrielle Ben Arous., 2013 Ben Arous, Tunisia. Tel: (+216) 79 389687, Fax: (+216) 71 385154. UAE: (Abu Dhabi) Light House
Electrical, P.O. Box 120, Abu Dhabi, Tel: (971-2) 6726131, Fax: (971-2) 6720667. Galaxy Equipment Trading, Madinath Zayed (Baada Zaid), Abu Dhabi P.C.
58910, Tel: (971-2) 8844279, Fax: (971-2) 8844297 (Ajman) Al Sukoon Gen. Trdg. Co. LLC, P.O. Box 2975, Ajman. Tel: (971-6) 7435725/ 7438317, Fax:
(971-6) 7437350. Al Sukoon Gen. Trdg. Co. LLC, P.O. Box 2975, Ajman, Tel: (971-6) 7435725 / 7438317, Fax: (971-6) 7437350 (Al Ain) Zillion Equipment and
Spare Parts Trading LLC, P.O. Box 19740, Opp. Bin Sadal/ Trimix Redymix Sanaiya, Al Ain. Tel: (971-3) 7216690, Fax: (971-3) 7216103. (Dubai) Black &
Decker (Overseas) GmbH, P.O. Box 5420, Dubai, Tel: (971-4) 8127400/ 8127406, Fax: (971-4)2822765. Ideal Star Workshop Eqpt.Trading LLC, P.O. Box
37116, Al Quoz, Dubai, Tel: (971-4) 3474160, Fax: (971-4) 3474157, Fine Tools, P.O.Box 30139 , Al Quoz, Dubai, Tel: (971-4) 3385240, Fax: (971-4) 3385239,
Alebrah Engineering Service, P.O. Box 78954, Al Qusais , Dubai, Tel: (971-4) 2850044, Fax: (971-4) 2844802. (Musaffah) Light House Electrical, P.O. Box
120, Abu Dhabi, Tel: (971-2) 5548315, Fax: (971-2) 5540461. (Sharjah) Mc Coy Middle East LLC, P.O. Box 25793, Sharjah, Tel: (971-6) 5395931, Fax:
(971-6) 5395932. Burj Al Madeena, Industrial Area No.1, Opp. Pakistani Masjid, P.O. Box 37635, Sharjah. Tel: (971-6) 5337747, Fax: (971-6) 5337719. Burj Al
Madeena, , Industrial Area No 1,opp Pakistani Masjid P.O. Box 37635, Sharjah, Tel: (971-6) 5337747, Fax: (971-6) 5337719 (Ras Al Khaimah) Mc Coy Middle
East LLC, P.O. Box 10584, Ras Al Khaimah, Tel: (971-7) 2277095, Fax: (971-7) 2277096. UGANDA: The Building Center (U) Ltd., 52 Station Road, Kitgum
House, P.O. Box 7436, Kampala, Uganda. Tel: (256-41) 4234567/ 4259754, Fax: (256-41) 4236413. YEMEN: (Aden) Middle East Trad. Co. Ltd. (METCO),
Mualla Dakka, Aden, Yemen. Tel: (967-2) 222670, Fax: (967-2) 222670. (Sana'a) Middle East Trad. Co. Ltd. (METCO), Hayel St., Sana'a, Yemen. Tel: (967-1)
204201, Fax: (967-1) 204204. (Taiz) Middle East Trading Co. (METCO), P.O. Box 12363, 5th Flr, Hayel Saeed Anam Bldg, Al-Mugamma St. Taiz, Yemen. Tel:
(967-4) 213455, Fax: (967-4) 219869.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising