DV1415EL | Black&Decker DV1415EL DUSTBUSTER Type H1 instruction manual

www.blackanddecker.co.uk
DV7215EL
DV1015EL
DV1415EL
DV1815EL
B
A
E
C
D
E
F
2
G
H
I
J
3
ENGLISH
(Original instructions)
Intended use
Your Black & Decker Dustbuster® handheld vacuum cleaner
has been designed for light dry vacuum cleaning purposes.
This appliance is intended for household use only.
u
Safety instructions
Never pull the charger lead to disconnect the charger from the socket. Keep
the charger lead away from heat, oil
and sharp edges.
This appliance can be used by children aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or
lack of experience and knowledge if
they have been given supervision or
instruction concerning use of the appliance in a safe way and understand the
hazards involved. Children shall not
play with the appliance. Cleaning and
user maintenance shall not be made
by children without supervision.
Warning! Read all safety
@ warnings and all instructions. Failure to follow
the warnings and instructions
listed below may result in electric
shock, fire and/or serious injury.
Warning! When using battery@ powered appliances, basic safety
precautions, including the following, should always be followed to
reduce the risk of fire, leaking batteries, personal injury and material Inspection and repairs
damage.
Before use, check the appliance for
Read all of this manual carefully bedamaged or defective parts. Check for
fore using the appliance.
breakage of parts, damage to switches
The intended use is described in this
and any other conditions that may afmanual. The use of any accessory
fect its operation.
or attachment or the performance
Do not use the appliance if any part is
of any operation with this appliance
damaged or defective.
other than those recommended in this Have any damaged or defective parts
instruction manual may present a risk
repaired or replaced by an authorized
of personal injury.
repair agent.
Retain this manual for future refer Regularly check the charger lead for
ence.
damage. Replace the charger if the
lead is damaged or defective.
Using your appliance
Never attempt to remove or replace
Do not use the appliance to pick up
any parts other than those specified in
liquids or any materials that could
this manual.
catch fire.
Do not use the appliance near water.
Do not immerse the appliance in
water.
u
u
u
u
u
u
u
u
u
u
u
u
4
(Original instructions)
Additional safety instructions
After use
u Unplug the charger before cleaning the charger.
u When not in use, the appliance should be stored in a dry
place.
u
Children should not have access to stored appliances.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving parts.
u Injuries caused when changing any parts, blades or accessories.
u Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Batteries and chargers
Batteries
u Never attempt to open for any reason.
u Do not expose the battery to water.
u Do not expose the battery to heat.
u Do not store in locations where the temperature may
exceed 40°C.
u
Charge only at ambient temperatures between 10°C and
u
Charge only using the charger provided with the appli-
40°C.
ance/tool. Using the wrong charger could result in an
electric shock or overheating of the battery.
u When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
u Do not damage/deform the battery pack either by puncture
or impact, as this may create a risk of injury and fire.
u Do not charge damaged batteries.
u Under extreme conditions, battery leakage may occur.
When you notice liquid on the batteries carefully wipe the
liquid off using a cloth. Avoid skin contact.
u In case of skin or eye contact, follow the instructions
below.
ENGLISH
Warning! The battery fluid may cause personal injury or
damage to property. In case of skin contact, immediately rinse
with water. If redness, pain or irritation occurs seek medical
attention. In case of eye contact, rinse immediately with clean
water and seek medical attention.
Chargers
Your charger has been designed for a specific voltage. Always
check that the mains voltage corresponds to the voltage on
the rating plate.
Warning! Never attempt to replace the charger unit with a
regular mains plug.
u Use your Black & Decker charger only to charge the battery in the appliance/tool with which it was supplied. Other
batteries could burst, causing personal injury and damage.
u Never attempt to charge nonrechargeable batteries.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
u Do not expose the charger to water.
u Do not open the charger.
u Do not probe the charger.
u The appliance/tool/battery must be placed in a well ventilated area when charging.
Electrical safety
Your charger has been designed for a specific voltage. Always
check that the mains voltage corresponds to the voltage on
the rating plate. Never attempt to replace the charger unit with
a regular mains plug.
Symbols on the charger
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
Short circuit proof safety isolating transformer. The
mains supply is electrically separated from the
transformer output.
$
The charging base is intended for indoor use only.
5
ENGLISH
(Original instructions)
Features
This tool includes some or all of the following features.
1. On/off switch
2. Bowl release button
3. Charging indicator
4. Dust bowl
5. Dust collector
6. Charger socket
7. Charger
Assembly
Accessories (fig. A & B)
These models may be supplied with some of the following
accessories:
u An Integrated brush tool (9) for furniture and stairs.
u An Integrated crevice tool (10) for confined spaces.
The integrated brush tool (Fig. A)
u Flip down the brush tool (9) at the end of the dust collector.
The integrated crevice tool (Fig. B)
u Extend the crevice tool (10) by pulling the crevice tool (10)
until it locks into position.
u Retract the crevice tool (10) by pressing the area (11) and
pushing the crevice tool (10) back into the dust collector
(5).
Installation
Wall Mounting (fig. C)
The product can be attached to a wall to provide a convenient
storage and charging point for the appliance.
When fixing to a wall, make sure that the fixing method is
suitable for the wall type and is appropriate to the weight of
the appliance.
u Mark the location of the screw holes (within reach of an
electrical outlet for chargeing the vac while it is on the wall
bracket).
u Insert the charger cord into the curved slot in the wall
mount bracket leaving approximately 8-9 inches excess.
u Hang the appliance on the wall by placing the opening
on the base of the vac over the hooks in the wall mount
bracket.
6
Use
u
Before first use, the battery must be charged for at least 4
hours.
Charging the battery (Fig. D)
u Make sure that the appliance is switched off. The battery
will not be charged with the on/off switch in the on position.
u Plug the jack plug of the charger (7) into the charging
socket (6) of the appliance.)
u Plug in the charger. Switch on at the mains. The charging
indicator (3) will be lit.
u Leave the appliance to charge for at least 4 hours.
While charging, the charger may become warm. This is
normal and does not indicate a problem. The appliance can
be left connected to the charger indefinitely. The charging
indicator (3) will be lit as long as the appliance is connected to
the plugged-in charger.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C.
Switching on and off (fig. E)
u To switch the appliance on, slide the on/off switch (1)
forward to position 1.
u
To switch the appliance off, slide the on/off switch (1) back
to position 0.
Rotating the dust collector (fig. F)
The nozzle can be rotated for better access in tight spots.
u Press the rotation release catch (12).
u Rotate the nozzle to the left or right until it clicks into
place.
Optimising the suction force
In order to keep the suction force optimised, the filters must be
cleared regularly during use.
Emptying and cleaning the product
Emptying the dust bowl (fig. G)
u Press the release latch (13) and pull the dust collector (5)
straight off.
Empty the contents of the bowl.
u To replace the dust collector, place it back onto the handle
u
until it “clicks” firmly into position.
(Original instructions)
Removing the dust bowl and filters (fig. H & I)
Warning! The filters are re-usable and should be cleaned
regularly.
u Press the release latch (2) and pull the dust bowl (4)
straight off.
u While holding the dust bowl over a bin or sink, pull out the
filter (14) to empty the contents of the bowl.
u To replace the dust bowl, place it back onto the handle
until it “clicks” firmly into position.
Warning! Never use the appliance without the filters. Optimum dust collection will only be achieved with clean filters.
Pre-filter (fig. J)
The Filter and pre-filter can be separated to allow better
cleaning.
u Twist the pre-filter (16) in a clockwise direction and lift
from the filter (15).
Cleaning the dust bowls and filters
u The dust bowls and filters can be washed in warm soapy
water.
u
Make sure that the filters and the dust bowl are dry before
re-fitting.
Replacing the filters
The filters should be replaced every 6 to 9 months and whenever worn or damaged.
Replacement filters are available from your Black & Decker
dealer:
For models: DV7215EL, DV1015EL, DV1415EL and
DV1815EL use filter part number VF110-XJ
Maintenance
Your Black & Decker corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
u Switch off and unplug the appliance/tool.
u Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
u Or run the battery down completely if it is integral and then
switch off.
u Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
ENGLISH
Protecting the environment
Z
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product available for separate collection.
z
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw
materials.
Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or
by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at
the address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
Battery
Z
If you want to dispose of the product yourself, the
battery must be removed as described below and
disposed of in accordance with local regulations.
u Preferably discharge the battery by operating the appliance until the motor stops.
u Press the release button (2) and remove the dust bowl (4).
u Remove the seven screws holding the body of the appliance together.
u Lift the housing cover away from the assembly.
u Detach all lead connections from the battery pack.
u Remove battery pack.
u Place the battery in a suitable packaging to ensure that
the terminals cannot be short-circuited.
u Take the battery to your service agent or to a local recycling station.
Once removed, the battery cannot be refitted.
7
(Original instructions)
ENGLISH
Guarantee
Technical data
Voltage
Battery
Weight
DV7215EL
DV1015EL
(H1)
(H1)
Vdc
7.2
10.8
Type
Li-Ion
Li-Ion
1.10
1.18
S010QV1400040
S010QV1400040
S010QB1400040
S010QB1400040
kg
Charger
Input voltage
Vac
100-240
100-240
Output voltage
Vdc
14
14
Current
mA
400
400
Approximate
h
4
4
0.08
0.08
charge time
Weight
Voltage
Battery
Weight
kg
DV1415EL
DV1815EL
(H1)
(H1)
Vdc
14.4
18
Type
Li-Ion
Li-Ion
1.23
1.3
S010QV2300040
S010QV2300040
S010QB2300040
S010QB2300040
kg
Charger
Input voltage
Vac
100-240
100-240
Output voltage
Vdc
23
23
Current
mA
400
400
Approximate
h
4
4
0.08
0.08
charge time
Weight
8
kg
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24
months from the date of purchase, Black & Decker guarantees
to replace defective parts, repair products subjected to fair
wear and tear or replace such products to ensure minimum
inconvenience to the customer unless:
u The product has been used for trade, professional or hire
purposes;
u The product has been subjected to misuse or neglect;
u The product has sustained damage through foreign
objects, substances or accidents;
u Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent
by contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our aftersales service and contacts are available on the Internet at:
www.2helpU.com
Please visit our website www.blackanddecker.co.uk to register
your new Black & Decker product and to be kept up to date
on new products and special offers. Further information on the
Black & Decker brand and our range of products is available
at www.blackanddecker.co.uk
(Original instructions)
ENGLISH
9
10
ENGLISH
Do not forget to register your product!
www.blackanddecker.co.uk/productregistration
Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product
code to Black & Decker in your country.
Australia
Black & Decker (Australia) Pty. Ltd.
20 Fletcher Road, Mooroolbark, Victoria, 3138
New Zealand
Black & Decker
5 Te Apunga Place
Mt Wellington
Auckland 1060
United Kingdom
Black & Decker
210 Bath Road
Slough, Berkshire SL1 3YD
www.blackanddecker.co.uk
emeaservice@sbdinc.com
90611512 REV-0
Tel. 03-8720 5100
Fax 03-9727 5940
Tel. +64 9 259 1133
Fax +64 9 259 1122
Tel. 01753 511234
Fax 01753 512365
05/2014
Download PDF