STSC2135 | Stanley STSC2135 CHOP SAW instruction manual

STSC2135
English
Page 3
ENGLISH
(Original instructions)
FIG. A
o
N
DIAMETER OF WORK PIECE
FIG. B
L
E
SPACE BLOCK
A
K
F
M
WIDTH OF SPACE BLOCK
J
X
FIG. C
F
I
CUT-OFF END
H
C
B
FIG. D
E
E
BLOCK
D
G
FIG. E
P
P
FORWARD
F
I
A
F
E
H
FIG. F
D
A
E
FIG. G
P
FIG. H
J
U
R
L
FIG. I
X
.3"
(8mm)
2
Y
V
W
T
S
(Original instructions)
Intended use
Your STANLEY Chop Saw has been designed for the cutting
of variously shaped steel materials.
General safety rules
Warning! Read all instructions. Failure to follow all
instructions listed below may result in electric shock, fire
and/or serious injury. The term “power tool” in all of the
warnings listed below refers to your mains operated
(corded) power tool or battery operated (cordless) power
tool. SAVE THESE INSTRUCTIONS.
Safety instructions
General power tool safety warnings
1. Work area safety
a. Keep work area clean and well lit. Cluttered and dark
areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose
control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk
of electric shock.
ENGLISH
Note: The term "Residual Curent Device (RCD)" can be
replaced by "Ground Fault Circuit Interrupter (GFCI)" or by
"Earth Leakage Circuit Breaker (ELCB)".
3. Personal safety
a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
b. Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c. Avoid accidental starting. Ensure the switch is in the
off position before plugging in. Carrying power tools
with your finger on the switch or plugging in power tools
that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
e. Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
toolin unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices
can reduce dust related hazards.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
4. Power tool use and care
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
f. If operating a power tool in a damp location is
aunavoidable, use a residual current device
(RCD)protected supply.Use of an RCD reduces the
risk of electric shock.
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools.Such preventive safety measures reduce
the risk of starting the power tool accidentally
3
ENGLISH
(Original instructions)
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Use the power tool, accessories and tool bits etc., in
accordance with these instructions, takinginto
account the working conditions and the work to be
performed. Use of the power tool for operations
different from those intended could result in a hazardous
situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is
maintained.
Additional safety instruction for chopsaws
•
Always wear proper eye and respiratory protection.
•
Before using, inspect the cutting wheel for cracks or
flaws. If such a crack or flaw is evident, discard the
wheel. The wheel should also be inspected
whenever you think the tool may have been
dropped. Flaws may cause wheel breakage.
•
When starting the tool with a new or replacement
wheel or if you are unsure of the condition of the
wheel, hold the tool in a well protected area and let it
run for one minute. If the wheel has an undetected
crack or flaw, it should burst in less than one minute.
Never start the tool with a person in line with the wheel.
This includes the operator.
•
•
Clean your chop saw periodically following the procedure
in this manual.
•
Do not remove wheel guards or base.
•
ALWAYS USE THE VISE OR SPECIAL FIXTURE TO
CLAMP WORK SECURELY. Other aids such as spring,
bar, or C-clamps may be appropriate for certain sizes
and shapes of workpiece. Use care in selecting and
placing these clamps and make a dry run before making
a cut.
•
Use only 14" type 1 wheels rated at 4100 rpm or higher.
•
Allow cut off parts to cool before handling.
•
Do not attempt to cut wood or plastic with this tool.
•
NEVER CUT MAGNESIUM WITH THIS TOOL.
•
Use chop saw in a well-ventilated area.
•
Turn chop saw off before removing any pieces from the
base.
•
DO NOT CUT ELECTRICALLY LIVE MATERIAL.
•
Do not use circular saw blades or any other toothed
blades with this tool.Serious injury may result.
•
DO NOT OPERATE THIS TOOL NEAR FLAMMABLE
LIQUIDS, GASES OR DUST.Sparks or hot chips from
cutting or arcing motor brushes may ignite combustible
materials.
•
Do not use the side of the abrasive wheel as a deburring
grinder. This will substantially weaken the wheel creating
an unsafe condition. The wheel may come apart.
Caution: Wear appropriate hearing protection
during use. Under some conditions and duration
ofuse, noise from this product may contribute to
hearing loss.
In operation, avoid bouncing the wheel or giving it
rough treatment. If this occurs, stop the tool andinspect
the wheel for cracks or flaws.
Caution:Spark deflector will get hot. Avoid
touching or adjusting while hot. Keep cordset
and materials away from spark deflector.
During use
•
If the saw blade becomes blocked, switch off the tool
immediately and disconnect the plug; only then remove
the wedged workpiece
•
In case of jamming or electrical or mechanical
malfunction, immediately switch off the tool and
disconnect the plug
4
•
Avoid prolonged contact with dust from power
sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing and
wash exposed areas with soap and water. Allowing
dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
(Original instructions)
Warning: Always use NIOSH/OSHA approved
respiratory protection appropriate for the dust
exposure. Direct particles away from face and
body.For your convenience and safety, the following
warnings are on your Heavy-Duty 14" (355mm) Chop Saw:
For safe operation read the instruction
manual.
ENGLISH
7. Labels on tool
The label on your tool may include the following symbols:
Read
Instructions
Manual
Use Eye
Protection
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
Use Ear
Protection
V ........ Volts
..... Direct
Current
...... Class II
Construction
....
Earthing
Terminal
....
Safety Alert
Symbol
.../min..
Revolutions
or Reciprocation per
minute
•
Do not use toothed blades.
•
Use only reinforced wheels rated 4100 rpm or higher.
Position of date barcode
•
When servicing use only identical replacement
parts.
•
Always: wear eye protection, use guards, clamp
work in vise, use proper respiratory protection.
The Date Code, which also includes the year of
manufacture, is printed into the housing.
Example:
2014 XX JN
Year of manufacturing
•
Do not expose to rain or use in damp locations.
•
Only use chop saw wheel of a max. Thickness of
2.8mm and a max. Diameter of 355mm.
Vibration
The declared vibration emission values stated in the
technical data and the declaration of conformity have been
measured in accordance with a standard test method
provided by EN 61029 and may be used for comparing one
tool with another. The declared vibration emission value may
also be used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level
may increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons
regularly using power tools in employment, an estimation of
vibration exposure should consider, the actual conditions of
use and the way the tool is used, including taking account of
all parts of the operating cycle such as the times when the
tool is switched off and when it is running idle in addition to
the trigger time.
A ........ Amperes
n 0 ....... No-Load
Speed
Electrical safety
Warning! If the power cord is damaged, it must bereplaced
by the manufacturer, authorized Stanley Service Center or
an equally qualified person in order to avoid damage or
injury.If the power cord is replaced by an equally qualified
person, but not authorized by Stanley, the warranty will not
be valid.
Features (fig. 1, 4)
A. Spark Deflector Screw
B. Spark Deflector
C. Base
D. Fence
E. Vise
F. Flat Wrench
G. Crank
H. Vise Level
I. Wheel
J. Guard
K. Spindle Lock
L. Depth Stop Bolt and Jam Nut
5
ENGLISH
(Original instructions)
M. Trigger Switch
Unlocking (fig. 1)
N. Padlock Hole
To unlock tool and raise head, depress motor arm slightly
and pull lock pin (X) out. Motor arm will then pivot upward.
O. Fence Bolts
Spark deflector adjustment (fig. 1)
P. Lock Pin
Power supply
Be sure your power supply agrees with the nameplate
marking. A voltage decrease of more than 10% will cause a
loss of power and overheating.
Cutting capacity
The wide vise opening and high pivot point provide cutting
capacity for many large pieces. Use the cutting capacity
chart to determine total maximum size of cuts that can be
made with a new wheel.
Caution: Certain large, circular or irregularly
shaped objects may require additional
holding means if they cannot be held
securely in vise.
Caution: do not cut magnesium with this tool.
Maximum cutting capacity
Note: Capacity shown on chart assumes no wheel wear and
optimum fence position.
Depth stop (fig. 1)
Depth stop is set at the factory for a new 14" wheel to
prevent wheel from cutting into the supporting surface.To
allow more depth of cut, use the flat wrench provided (F) to
loosen the depth stop bolt (L) and raise bolt todesired height
and then turn jam nut (L) clockwise until seated firmly on the
casting. Securely tighten the depth stop bolt before use.
Caution: When changing to a new wheel,
readjust epth stop to original position to prevent
cutting intosupporting surface.
Trigger switch (fig. 1)
To start the tool, depress the trigger switch (M). To turn the
tool off, release the trigger switch. Keep hands and material
from wheel until it has coasted to a stop.To prevent
unauthorized use of tool, install a standard padlock (not
included) into the padlock hole (N) located inthe trigger.
Material clamping and supporting
Workpiece
Shape:
AxB
90°
Cutting
Angle
A = 4-7/8"
(125mm)
A = 4-1/2"
(115mm)
4-1/2" x 5-1/8"
A = 4-1/2" x 5-3/8"
(115mm x 130mm) (115mm x 137mm)
4" x 7-5/8"
(102mm x 188mm)
3" x 7-3/8"
(76mm x 229mm)
45°
Cutting
Angle
A= 4-1/2"
(115mm)
A = 3-13/16"
(98mm)
4-1/2" x 3-13/16" A = 3-13/16"
3-3/4"
4-1/8" x 3-3/4"
(105mm x 95mm) (95mm)
Use
Standard equipment
•
355mm Metal Cutting Abrasive Wheel
•
1 Wheel Wrench
•
1 Instruction manual
To carry (fig. 1)
Fold down unit to position where you can carry the saw.
Push in lock pin (X) to lock arm down.
6
To best deflect sparks away from surrounding persons and
materials, loosen the screw (A), adjust the spark deflector
(B) and then retighten screw. Do not allow cordset to come
into contact with deflector or sparks as damage to cordset
may occur.
•
Angles are best clamped and cut with both legs resting
against base.
•
A spacer block slightly narrower than the work piece can
be used to increase wheel utilization (Fig. 2).
•
Long work pieces must be supported by a block so it will
be level with top of base (Fig. 3). The cut off end should
be free to fall downward to avoid wheel binding.
Vise operation (fig. 4)
The vise (E) has a quick-travel feature. To release the vise
when it is clamped tightly, turn the crank (G)
counterclockwise one or two times to remove clamping
pressure. Lift vise lever (H) up. Pull crank assembly out as
far asdesired. Vise may be pushed forward into work without
cranking. Lower vise lever (H) then tighten vise (E) onwork
by using crank (G).
Fence operation (fig. 5, 6)
Caution: Turn off and unplug the tool before
making any adjustments or removing or
installing attachments or accessories. Be
sure the trigger switch is in the OFF position.The fence
(D) can be adjusted two ways: to change desired cutting
angle and to change spacing between the fence and vise.
(Original instructions)
To change the desired cutting angle
Use the wrench provided to loosen (do not remove) the two
fence bolts (O). Align the desired angle indicator line with
theslot line in the base (C). Securely tighten both fence bolts
before use. For more accurate square cuts, disconnect the
power supply, loosen the two fence bolts, push arm down
until wheel extends into base. Place a square against
thewheel and adjust fence against the square. Securely
tighten both fence bolts before use. When making a miter
cut, the vise (E) may not clamp securely, depending on the
thickness of the workpiece and the miter angle. Other aids
(such as spring, bar or C-clamps) will be necessary to
secure the work piece to the fence when making these cuts.
To change spacing between the fence and vise
Using the wrench provided, loosen and remove the two
fence bolts (O). Adjust the fence (D) to desired
locations.Insert both fence bolts in provided locations.
Securely tighten both fence bolts before use.
Removal and installation of wheels (fig. 7, 8)
Caution: Turn off and unplug the tool before
making any adjustments or removing or
installin gattachments or accessories. Be
sure the trigger switch is in the OFF position. Do not
make any adjustment while the wheel is in motion. Do not
make any adjustment while chop saw is plugged into power
supply.
1. Push in spindle lock (K) and rotate wheel (I) by hand
until wheel lock lever engages slot in inside flange(Q) to
lock wheel. Loosen the bolt (R) counterclockwise in the
center of the abrasive wheel with the 8mm hex wrench
(F). Bolt has right-hand thread.
2. Remove the bolt (S), washer (R), outside flange (T) and
old wheel (I).
3. Make sure flange surfaces are clean and flat. Install the
new abrasive wheel by reversing the above steps.
4. Do not overtighten bolt.
Warning: Check the work surface that the chop
saw rests on when replacing with a new
abrasive wheel. Itis possible that the wheel may
contact ANY ITEMS OR STRUCTURE THAT EXTENDS
ENGLISH
ABOVE work surface (under the base) when the arm is fully
lowered.
Operation tips for more accurate cuts
•
Allow the wheel to do the cutting. Excessive force will
cause the wheel to glaze reducing cutting efficiency
and/or to deflect causing inaccurate cuts.
•
Properly adjust fence angle.
•
Make sure material is laying flat across base.
•
Properly clamp material to avoid movement and
vibration.
Motor brush inspection and replacement (fig.9)
Warning:Turn off and unplug the tool. Be sure
the trigger switch is in the OFF position.
Brushes should be regularly inspected for wear.
To inspect brushes, unscrew the two end cap screws (V) and
remove end cap (W). Remove brush cap (Y). Brushes (X)
should slide freely in brush box.
If brushes are worndown to .3" (8mm) as shown in Figure 9
they should be replaced. To reinstall, push new brush back
into brushbox. If replacing existing brush, maintain same
orientation as when removed. Replace the brush cap (do not
overtighten). Replace end cap and two screws. Tighten
securely.
Accessories
The performance of any power tool is dependent upon the
accessory used. STANLEY accessories areengineered to
high quality standards and are designed to enhance the
performance of power tool.
Note: Accessory must be rated for use at speed
equal to or higher than nameplate RPM of tool
with which it is being used.
Caution: The use of any other accessory not recommended
for use with this tool could be hazardous.Use only
high-strength Type 1 organic bonded wheels rated 4100 rpm
or higher. Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center.
7
ENGLISH
(Original instructions)
Maintenance
Your STANLEY power tool has been designed to operate
over a long period of time with a minimum of
maintenance.Continuous satisfactory operation depends
upon proper tool care and regular cleaning.Your tool is not
user-serviceable. Take the tool to an authorized STANLEY
repair agent. This tool should be serviced at regular
intervals or when showing a noticeable change in
performance.
Lubrication
STANLEY power tools are properly lubricated at the factory
and are ready for use. Tools should be re-lubricated
regularly , depending on usage. This lubrication should only
be attempted by trained power tool repair persons, such as
those at STANLEY service centers or by other qualified
service personnel. Closed-type, grease-sealed ball bearings
are used throughout. These bearings have sufficient
lubricationpacked in them at the factory to last the life of the
chop saw.
Cleaning
Warning: unplug the tool before you use a cloth
to clean the housing.With the motor running,
blow dirt and dust out of all air vents with dry air
at least once a week. Wear safety glasses when performing
this. Exterior plastic parts may be cleaned with a damp cloth
and mild detergent. Although these parts are highly solvent
resistant, NEVER use solvents.
Blowing dust and grit out of the main housing by means of
an air hose is recommended and may be done as often as
dirt is seen collecting in and around the air vents. Always
wear proper eye and respiratory protection.
Tool care
Avoid overloading the machine.Overloading will result in a
considerable reduction in speed and efficiency and the unit
will become hot. In this event,run the machine at no load for
a minute or two until cooled to normal working temperature
8
by the built in fan. Switching your machine on and off whilst
under load will considerably reduce the life of the switch.
Important
To ensure product SAFETY and RELIABILITY, repairs,
maintenance and adjustment (other than those listed in this
manual) should be performed by authorized service centers
or other qualified organizations, always-using identical
replacement parts. Unit contains no user serviceable parts
inside.Blowing dust and grit out of the main housing by
means of an air hose is recommended and may be done as
often as dirt is seen collecting in and around the air vents.
Always wear proper eye and respiratory protection.
Note: Unit may be converted to a 3-wire twist lock cord set
at an authorized service center.
Notes
•
STANLEY's policy is one of continuous improvement to
our products and, as such, we reserve the right
tochange product specifications without prior notice.
•
Standard equipment and accessories may vary by
country.
•
Product specifications may differ by country.
•
Complete product range may not be available in all
countries.
•
Contact your local STANLEY dealers for range
availability.
(Original instructions)
ENGLISH
EC declaration of conformity
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your STANLEY product needs
replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for raw
materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
STANLEY provides a facility for the collection and recycling
of STANLEY products once they have reached the end of
their working life. To take advantage of this service please
return your product to any authorised repair agent who will
collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local STANLEY office at the
address indicated in this manual. Alternatively, a list of
authorised STANLEY repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
Technical data
Specifications
STSC2135
POWER
W
2100
NO-LOAD SPEED
/min
3800
MAX. DIAMETER
mm
355
Weight
kg
15.5
LpA (sound pressure)
dB(A)
95,5
KpA (sound pressure uncertainty)
dB(A)
3
LWA (sound power)
dB(A)
105,5
KWA (sound power uncertainty)
dB(A)
3
MACHINERY DIRECTIVE
STSC2135
STANLEY declares that these products described under
"technical data" are in compliance with:
2006/42/EC, EN 61029-1, EN 61029-2-10
These products also comply with Directive
2004/108/EC (until 19.04.2016),
2014/30/EU (from 20.04.2016) and 2011/65/EU.
For more information, please contact STANLEY at the
following address or refer to the back of the manual.
The undersigned is responsible for compilation of the
technical file and makes this declaration on behalf of
STANLEY.
R.Laverick
Engineering Manager
STANLEY , Europe, Egide Walschaertsstraat14-18,
2800 Mechelen, Belgium
01.2015
Vibration emission value ah
ah =
Uncertainty K =
m/s²
4.3
m/s²
1.5
9
ENGLISH
(Original instructions)
Service Information
STANLEY offers a full network of company-owned and
authorized service locations. All STANLEY Service Centers
are staffed with trained personnel to provide customers with
efficient and reliable power tool service. For more information
about our authorized service centers and if you need
technical advice, repair, or genuine factory replacement
parts, contact the STANLEY location nearest you.
One years full warranty
If your STANLEY product becomes defective due to faulty
materials or workmanship within 12 months from the date of
purchase, STANLEY guarantees to replace all defective
parts free of charge or – at our discretion – replace the unit
free of charge provided that:
•
The product has not been misused and has been used in
accordance with the instruction manual.
•
The product has been subject to fair wear and tear;
•
Repairs have not been attempted by unauthorised
•
Proof of purchase is produced.
•
The STANLEY product is returned complete with all
original components
If you wish to make a claim, contact your seller or check the
location of your nearest authorised STANLEY repair agent in
the STANLEY catalogue or contact your local STANLEY
office at the address indicated in this manual. A list of
authorised STANLEY repair agents and full details of our
after sales service is available on the internet
at:www.stanleytools.com
10
01/2015
Names & Addresses for STANLEY Service Concessionaries - MIDDLE EAST & AFRICA
ALGERIA: Sarl Outillage Corporation, 08 Rue Med Boudiaf - Cheraga - Algiers, Algeria. Tel: (213-21) 375130, Fax: (213-21) 369667. ANGOLA: Angoferraria,
Lda., Rua Robert Shields, No. 61, Luanda, Angola, Tel: 00244-222-395837 / 222-395034, Fax: 00244-222-394790. AZERBAIJAN: Royalton Holdings Ltd. 41
Khagani St. Apt. 47 AZ 1001, Baku. Tel: (994-12) 4935544, Fax: (994-12) 5980378. BAHRAIN: Kavalani & Sons W.L.L., P.O. Box 71, Sitra, Manama, Tel: (973)
17732888, Fax: (973) 17737379. Alfouz Services Co. WLL., P.O. Box 26562, Tubli, Manama. Tel: (973) 17783562, Fax: (973) 17783479. EGYPT: El Farab
S.A.E., 15-Nabil El Wakkad Street, Dokki, Giza, Egypt, Tel: 00202-37603946 / 002-010-2582544, Fax: 00202-33352796. ETHIOPIA: Seif Tewfik Sherif, Arada
Sub-City, Kebele 01/02, Global Insurance Building, 2nd Floor, Room 43, P.O. Box 2525, Addis Ababa, Ethiopia. Tel: (251-11) 1563968/ 1563969, Fax: (251-11)
1558009. IRAQ: Financial Links, Kazzaz Building Arasat Al-Hindia Block No: 629 Street: 31Building No: 1 Baghdad – Iraq. Tel: 00964 (0)780 195 2223/ 00964
(0)781 3763044. Al Sard Co. for General Trading Ltd. Jbara Bldg. 3Flr, Al Rasheed St. Bagdad. Tel: (964) 18184102. Sakhar Group, Arrassat al-hindya Al
Masbah, Bagdad. (964) 7400144446. JORDAN: Palestine Bldg. Matl. (Bashiti Hardware), 93 King Abdullah 2nd Street, Opp. ELBA House, P.O. Box 3005,
Amman 11953, Tel: (962-6) 5349098, Fax: (962-6) 5330731. KENYA: Dextron Tools Ltd., P.O. Box 20121-00200, Shariff House, Kimathi Street, Nairobi. Tel:
(254-20) 6905000/ 2358021, Fax: (254-20) 6905111/ 6905112. KUWAIT: Al Omar Technical Co., P.O. Box 4062, 13041 Safat, Kuwait. Tel: (965) 24848595/
24840039, Fax: (965) 24845652. Fawaz Al Zayani Establishment, P.O. Box 42426, Shop No. 18, Al Humaizi Commercial Complex, Khalifa Al Jassim,
Shuwaikh, Kuwait. Tel: (965) 24828710, Fax: (965) 24828716. Fawaz Al Zayani Establishment, P.O. Box 42426, Shop No.18, Al Humaizi Commercial
Complex, Khalifa Al Jassim, Shuwaikh, Kuwait, Tel: (965) 24828710, Fax: (965) 24828716. Fawaz Al Zayani Establishment, Fahaheel Industrial Area, Main St.,
Sanaya, Kuwait, Tel: (965) 23925830, Fax: (965) 24828716. LEBANON: Est. Shaya & Azar S.A.R.L., Boulvard Jdeideh - Mar Takla - Bouchrieh .P.O. Box
90545 Jdeideh.Beirut - Lebanon, Tel: 00961 1 872305 / 306 , Fax: 00961 1 872303. LIBYA: North Africa Trading ( El Ghoul Brothers), AlHilal Service Center
Tawergha St. Misurata, Tel: 00218-091-3221408. (Benghazi) Sniydel st., Amr Ibn EL-Aas Rd. Tel: (+218) 92 5771120. (Tripoli) Al Barniq Service Center,
Mokhazin elsukar st., ElFallah. Tel: (+218) 21 4808019. (Misrata) Al Hilal Service Center, Tawergha st. Tel: (+218) 51 2626743. MAURITIUS: Robert Le Marie
Limited, Old Moka Road, Bell Village, P.O. Box 161, Port Louis, Tel: 00230-212 1865/ 212 2847, Fax: 00230-2080843. MOROCCO: Ets Louis Guillaud & Cie,
149, Quartier Industriel, Moulay Rachid, Casablanca, Postal Code 20450, Morocco, Tel: 00212-522729233, Fax: 00212-522729096. NIGERIA: Meridian
Power Tools Ltd., Gr.Floor, #1 Alhaji Masha Rd, Next toTeslim Balogun Stadium, Near National Stadium Surulere, Lagos, Nigeria, Tel: 00234-1-7740431 /
7740410, Fax: 00234-1-7913798. OMAN: Al Jizzi Company LLC, P.O. Box 1704,PC 112 Ruwi, Oman, Tel: (968) 24832618/ 24835153, Fax: (968)
24831334/24836460. Al Hassan Technical & Construction Supplies Co. LLC, P.O. Box 1948, P.C. 112, Ruwi, Tel: (968) 24810575 / 24837054, Fax: (968)
24810287/ 24833080. Oman Hardware Co. LLC, P.O. Box 635, Ruwi Postal Code 112, Te: (968) 24815131, Fax: (968) 24816491. Khimji Ramdas, P.O. Box
19, Post Code 100, Ghala, Muscat, Oman. Tel: (968) 24595906/ 907, Fax: (968) 24852752. Oman Marketing & Service Co. (Omasco), P.O. Box 2734, Behind
Honda Showroom, Wattayah, Oman. Tel: (968) 24560232/ 24560255, Fax: (968) 24560993. Oman Marketing & Service Co. (Omasco), Al Ohi, Sohar, Oman.
Tel: (968) 26846379, Fax: (968) 26846379. Oman Marketing & Service Co. (Omasco), Sanaya, Salalah, Oman. Tel: (968) 23212290, Fax: (968) 23210936.
PAKISTAN: ZIT Co - Nasir & Bros., 2nd Floor, Qadri Center, Chowk Dalgran Railway Road, Lahore, Pakistan, Tel: 0092 42 37670839, Fax: 0092 42
37652989. Ammar Service & Spares, 60-Bank Arcade, Serai Road, Karachi, Pakistan. Tel: (92-21) 32426905, Fax: (92-21) 32427214. QATAR: Teyseer
Industrial Supplies & Services Co. WLL, 55, Al Wakalat St. (Between St. 18 & 19) Salwa Industrial Area, P.O. Box 40523 Doha,Qatar, Te: (974) 44581536, Fax:
(974) 44682024. Shaheen Electrical Works & Trading Co. WLL, Gate 34, St. 44 Industrial Area P.O. Box 9756, Doha, Tel: (974) 44600230 /44600525, Fax:
(974) 44601338. Al Muftah Service Centre, Al Wakrah Road, P.O. Box 875, Doha,Qatar, Tel: (974) 44650880/ 44650110/ 44446868, Fax: (974) 44441415 /
44662599. SAUDI ARABIA: (Al Bahr) Mohamed Ahmed Bin Afif Est., P.O. Box 530, Yanbu, Al Bahr. Tel: (966-4) 3222626/ 3228867, Fax: (966-4) 3222210.
(Al Khobar) Fawaz Ebrahim Al Zayani Trading Est., P.O. Box 76026, Al Khobar # 31952, Tel: (966-3) 8140914, Fax: (966-3) 8140824. MSS (Al-Mojil Supply &
Services) P.O. Box 450, Jubail 31951, Opp. Gulf Bridge Library & Riyadh House. Tel: (966-3) 3612850/ 3624487/ 3621729, Fax: (966-3) 3623589/ 3620783.
(Dammam) MSS (Al-Mojil Supply & Services), P.O. Box 450, Jubail 31951.Opp-Gulf Bridge Library & Riyadh House, Tel: (966-3) 3612850 / 3624487 /
3621729, Fax: (966-3) 3623589 / 3620783. Al Bawardi Tools & Hardware, P.O. Box 112, Dammam, Tel: (966-3) 8330780 Ext.24 / 8348585 Ext. 24 /
+966-3-8335555, Fax: (966-3) 8336303. (Al Hassa) Mutawa Trading & Gen. Services, Maliki road Hafuf city, Al Hassa, KSA. Tel: (966) 502846275 (Jeddah) Al
Bawardi Tools & Hardware, P.O. Box 16905, Jeddah 21474, Tel: (966-2) 6444547 / 6439035 / 6456095, Fax: (966-2) 6439024. EAC (Al Yousef Contg. & Trdg.
Est.), P.O. Box 30377, Jeddah -21477, Tel: (966-2) 6519912, Fax: (966-2) 6511153. (Madina) Garziz Trading for Bldg Mat & Decoration, P.O. Box 3364,
Madina, Tel: (966-4) 826 14 90 / 8227636, Fax: (966-4) 8265741. (Riyadh) Industrial Material Organization (IMO), P.O. Box 623, Rail Street ,Riyadh, Tel:
(966-1) 4028010 Ext 26 / 8001245757, Fax: (966-1) 4037970. Sultan Garment Factory (RSC), P.O. Box 29912, Riyadh 11467, KSA, Tel: (966-1) 4055148 /
4042889, Fax: (966-1) 4055148. Al Bawardi Tools & Hardware, P.O. Box 68, Riyadh 11411, Tel: (966-1) 4484999, Fax: (966-1) 4487877. (Yanbu) Fawaz
Ebrahim Al Zayani, Opposite to Al Fouzan, Jeddah highway or King Abdul Aziz road, Yanbu. Tel: (966-4) 3960980, Fax: (966-4) 3961980. Mohamed Ahmed
Bin Afif Est., P.O. Box 530, Yanbu, Al Bahr, Tel: (966-4) 3222626/ 3228867, Fax: (966-4) 3222210. SOUTH AFRICA: Stanley Black & Decker - RSA, 199
Winze Drive Stormill Ext 9 Roodepoort, Tel: (2711) 472 0454, Fax: (2711) 472 0482. Trevco Power Tool Service 14 Steenbok Street, Koedoespoort, 0186,
Pretoria, South Africa. Tel: (27-86) 1873826, Fax: (27-86) 5001771. TANZANIA: General Motors investment Ltd., P.O. Box 16541, 14 Nyerere Road,
Vingunguti, Dar-es-Salaam. Tel: (255 22) 2862661/ 2865022, Fax: (255 22) 2862667. TUNISIA: Societe Tunisienne De Maintenance (STM), Rue de la
Physique. Nouvelle Zone Industrielle Ben Arous., 2013 Ben Arous, Tunisia. Tel: (+216) 79 389687, Fax: (+216) 71 385154. UAE: (Abu Dhabi) Light House
Electrical, P.O. Box 120, Abu Dhabi, Tel: (971-2) 6726131, Fax: (971-2) 6720667. Galaxy Equipment Trading, Madinath Zayed (Baada Zaid), Abu Dhabi P.C.
58910, Tel: (971-2) 8844279, Fax: (971-2) 8844297 (Ajman) Al Sukoon Gen. Trdg. Co. LLC, P.O. Box 2975, Ajman. Tel: (971-6) 7435725/ 7438317, Fax:
(971-6) 7437350. Al Sukoon Gen. Trdg. Co. LLC, P.O. Box 2975, Ajman, Tel: (971-6) 7435725 / 7438317, Fax: (971-6) 7437350 (Al Ain) Zillion Equipment and
Spare Parts Trading LLC, P.O. Box 19740, Opp. Bin Sadal/ Trimix Redymix Sanaiya, Al Ain. Tel: (971-3) 7216690, Fax: (971-3) 7216103. (Dubai) Black &
Decker (Overseas) GmbH, P.O. Box 5420, Dubai, Tel: (971-4) 8127400/ 8127406, Fax: (971-4)2822765. Ideal Star Workshop Eqpt.Trading LLC, P.O. Box
37116, Al Quoz, Dubai, Tel: (971-4) 3474160, Fax: (971-4) 3474157, Fine Tools, P.O.Box 30139 , Al Quoz, Dubai, Tel: (971-4) 3385240, Fax: (971-4) 3385239,
Alebrah Engineering Service, P.O. Box 78954, Al Qusais , Dubai, Tel: (971-4) 2850044, Fax: (971-4) 2844802. (Musaffah) Light House Electrical, P.O. Box
120, Abu Dhabi, Tel: (971-2) 5548315, Fax: (971-2) 5540461. (Sharjah) Mc Coy Middle East LLC, P.O. Box 25793, Sharjah, Tel: (971-6) 5395931, Fax:
(971-6) 5395932. Burj Al Madeena, Industrial Area No.1, Opp. Pakistani Masjid, P.O. Box 37635, Sharjah. Tel: (971-6) 5337747, Fax: (971-6) 5337719. Burj Al
Madeena, , Industrial Area No 1,opp Pakistani Masjid P.O. Box 37635, Sharjah, Tel: (971-6) 5337747, Fax: (971-6) 5337719 (Ras Al Khaimah) Mc Coy Middle
East LLC, P.O. Box 10584, Ras Al Khaimah, Tel: (971-7) 2277095, Fax: (971-7) 2277096. UGANDA: The Building Center (U) Ltd., 52 Station Road, Kitgum
House, P.O. Box 7436, Kampala, Uganda. Tel: (256-41) 4234567/ 4259754, Fax: (256-41) 4236413. YEMEN: (Aden) Middle East Trad. Co. Ltd. (METCO),
Mualla Dakka, Aden, Yemen. Tel: (967-2) 222670, Fax: (967-2) 222670. (Sana'a) Middle East Trad. Co. Ltd. (METCO), Hayel St., Sana'a, Yemen. Tel: (967-1)
204201, Fax: (967-1) 204204. (Taiz) Middle East Trading Co. (METCO), P.O. Box 12363, 5th Flr, Hayel Saeed Anam Bldg, Al-Mugamma St. Taiz, Yemen. Tel:
(967-4) 213455, Fax: (967-4) 219869.
Download PDF