STGL2223 | Stanley STGL2223 ANGLE GRINDER - GQ instruction manual

STGL2023
STGL2223
English
Page 5
ENGLISH
(Original instructions)
2
1
4
3
A
3
6
20
7
5
B
2
C1
(Original instructions)
10
ENGLISH
10
8
8
6
7
9
6
7
10
8
6
7
C2
C3
3
10
90o
11
10
4
D
E
3
ENGLISH
(Original instructions)
15o-30o
F
G
4
A
B
(Original instructions)
Specifications
1) Work area safety
STGL2023
STGL2223
Input voltage
VAC
220-240
220-240
Power input
W
2000
2200
Hz
50/60
50/60
min-1
6500
6500
Frequency
No-load speed
Wheel diameter
mm
230
230
M14
M14
mm
6.6
6.6
kg
5.0
6.0
Spindle size
Max disc thickness
Grinding discs
Weight
ENGLISH
a) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
2) Electrical safety
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
these symbols.
Danger: Indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
Warning: Indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
Caution: Indicates a potentially hazardous
situation which, if not avoided, may result in minor
or moderate injury.
Notice: Indicates a practice not related to personal injury
which, if not avoided, may result in property damage.
Denotes risk of electric shock.
Denotes risk of fire.
Warning: To reduce the risk of injury, read the
instruction manual.
General power tool safety warnings
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire
and/or serious injury.
Save all warnings and instructions for future reference
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric
shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
5
ENGLISH
(Original instructions)
b) Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c) Prevent unintentional starting. Ensure the switch is
in the off position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch on
invites accidents.
d) Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment or
6
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in
accordance with these instructions taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous
situation.
5) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is
maintained.
Additional specific safety rules
Safety instructions for all operations
Safety warnings common for grinding
a) This power tool is intended to function as a grinder.
Read all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury.
b) Operations such as cutting-off , sander, wire brush
or polisher are not recommended to be performed
with this power tool. Operations for which the power
tool was not designed may create a hazard and cause
personal injury.
c) Do not use accessories which are not specifically
designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
d) The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated speed
can break and fly apart.
e) The outside diameter and the thickness of your
accessory must be within the capacity rating of your
power tool. Incorrectly sized accessories cannon be
adequately guarded or controlled.
(Original instructions)
f) The arbour size of wheels, flanges, backing pads or
any other accessory must properly fit the spindle of
the power tool. Accessories with arbour holes that do
not match the mounting hardware of the power tool will
run out of balance, vibrate excessively and may cause
loss of control.
g) Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheel for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked wires.
If power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory, position
yourself and bystanders away from the plane of the
rotating accessory and run the power tool at
maximum no-load speed for one minute. Damaged
accessories will normally break apart during this test
time.
h) Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of
stopping small abrasive or workpiece fragments.
The eye protection must be capable of stopping flying
debris generated by various operations. The dust mask
or respirator must be capable of filtrating particles
generated by your operation. Prolonged exposure to
high intensity noise may cause hearing loss.
i) Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment. Fragments of
workpiece or of a broken accessory may fly away and
cause injury beyond immediate area of operation.
ENGLISH
n) Regularly clean the power tool’s air vents. The
motor’s fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause
electrical hazards.
o) Do not operate the power tool near flammable
materials. Sparks could ignite these materials.
p) Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in
electrocution or shock.
Further safety instructions for all operations
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or snagged
rotating wheel, backing pad, brush or any other accessory.
Pinching or snagging causes rapid stalling of the rotating
accessory which in turn causes the uncontrolled power tool
to be forced in the direction opposite of the accessory’s
rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by
the workpiece, the edge of the wheel that is entering into the
pinch point can dig into the surface of the material causing
the wheel to climb out or kick out. The wheel may either
jump toward or away from the operator, depending on
direction of the wheel’s movement at the point of pinching.
Abrasive wheels may also break under these conditions.
Kickback is the result of tool misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below:
j) Hold the power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring or its
own cord. Cutting accessory contacting a “live” wire
may make exposed metal parts of the power tool “live”
and could give the operator an electric shock.
a) Maintain a firm grip on the power tool and position
your body and arm to allow you to resist kickback
forces. Always use auxiliary handle, if provided, for
maximum control over kickback or torque reaction
during start up. The operator can control torque
reaction or kickback forces, if proper precautions are
taken.
k) Position the cord clear of the spinning accessory. If
you lose control, the cord may be cut or snagged and
your hand or arm may be pulled into the spinning
accessory.
b) Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
l) Never lay the power tool down until the accessory
has come to a complete stop. The spinning accessory
may grab the surface and pull the power tool out of your
control.
m) Do not run the power tool while carrying it at your
side. Accidental contact with the spinning accessory
could snag your clothing, pulling the accessory into your
body.
c) Do not position your body in the area where power
tool will move if kickback occurs. Kickback will propel
the tool in direction opposite to the wheel’s movement at
the point of snagging.
d) Use special care when working corners, sharp edges
etc. Avoid bouncing and snagging the accessory.
Corners, sharp edges or bouncing have a tendency to
snag the rotating accessory and cause loss of control or
kickback.
7
ENGLISH
(Original instructions)
e) Do not attach a saw chain woodcarving blade or
toothed saw blade. Such blades create frequent
kickback and loss of control.
Safety Warnings Specific for Grinding
Operations
a) Use only wheel types that are recommended for
your power tool and the specific guard designed for
the selected wheel. Wheels for which the power tool
was not designed cannot be adequately guarded and
are unsafe.
b) The guard must be securely attached to the power
tool and positioned for maximum safety, so the least
amount of wheel is exposed towards the operator.
The guard helps to protect operator from broken wheel
fragments and accidental contact with wheel and sparks
that could ignite clothing.
c) Wheels must be used only for recommended
applications. For example: do not grind with the side
of cut-off wheel. Abrasive cut-off wheels are intended
for peripheral grinding, side forces applied to these
wheels may cause them to shatter.
technical data and the declaration of conformity have been
measured in accordance with a standard test method
provided by EN 60745 and may be used for comparing one
tool with another. The declared vibration emission value may
also be used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level
may increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons
regularly using power tools in employment, an estimation of
vibration exposure should consider, the actual conditions of
use and the way the tool is used, including taking account of
all parts of the operating cycle such as the times when the
tool is switched off and when it is running idle in addition to
the trigger time.
Labels on tool
The label on your tool may include the following symbols:
Read
Instructions
Manual
Use Eye
Protection
d) Always use undamaged wheel flanges that are of
correct size and shape for your selected wheel.
Proper wheel flanges support the wheel thus reducing
the possibility of wheel breakage. Flanges for cut-off
wheels may be different from grinding wheel flanges.
e) Do not use worn down wheels from larger power
tools. Wheel intended for larger power tool is not
suitable for the higher speed of a smaller tool and may
burst.
Residual Risks
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These are:
– Impairment of hearing
– Risk of personal injury due flying particles.
– Risk of burns due to accessories becoming hot during
operation.
– Risk of personal injury due to prolonged use.
– Risk of dust from hazardous substances.
Vibration
The declared vibration emission values stated in the
8
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
Use Ear
Protection
V ........ Volts
A ........ Amperes
..... Direct
Current
...... Class II
Construction
....
Earthing
Terminal
....
Safety Alert
Symbol
.../min..
Revolutions
or Reciprocation per
minute
n 0 ....... No-Load
Speed
Position of date barcode
The Date Code, which also includes the year of
manufacture, is printed into the housing.
Example:
2014 XX JN
Year of manufacturing
Package Content
This product package includes:
1
1
1
1
1
1
Angle grinder
Guard
Flange set
Spanner
Handle
Instruction manual
•
Check the tool, parts, and accessories to see if they are
damaged during transportation.
•
Take a few moments to read and understand this manual
before using the tool.
(Original instructions)
Description (Fig. 1)
Warning: Never modify the power tool or any part
of the tool, otherwise it may cause damage to the
tool or result in personal injury.
a. ON/OFF switch
b. Spindle lock
c. Guard
Purpose of design
This angle grinder is designed especially for grinding.
Do not use sandpaper discs and grinding wheels other than
those with depressed center.
Do not use the tool in wet conditions or environments in the
presence of flammable liquids or gases.
This heavy-duty angle grinder is a professional power tool.
Do not allow children to come in contact with this tool.
Inexperienced operators are required to use this tool under
supervision.
Electrical Equipment Safety
Only one voltage is applicable to this tool. Be sure
to check that the power suuply corresponds to the
voltage on the rating plate. Your STANLEY tool is
equipped with double insulation, hence, it does not require
to be earthed.
When the power cord is damaged, have it sent to a
STANLEY service center for replacement to specially
prepared cables.
Using Extension Cords
If an extension cord is required, please select a 3-phase
extension cord that has been inspected and matches the
input power (see Technical Data) of this tool. The minimum
conductor size is 1.5mm2, maximum length is 30 meters.
When using a cable reel, be sure to pull out all the cables.
Assembly and Adjustment
Warning: To minimize the danger of serious
personal injury, please switch off the tool
power and disconnect all plugs before adjusting or
removing/installing any accessory. Before reassembling
the tool, press and release the trigger switch to make sure
the tool is already switched off.
Attaching and Removing the Wheel Guard (Fig. B)
ENGLISH
personal injury, please switch off the tool power and
disconnect all plugs before adjusting or
removing/installing any accessory. Before reassembling
the tool, press and release the trigger switch to make sure
the tool is already switched off.
Attaching the guard
1. Place the angle grinder on a work bench, groove facing
up.
2. Bring the flange of the guard (3) collar over the groove
(11) of the gear housing.
3. Turn the guard (4) counterclockwise by 150 degrees.
4. Make sure that the screws (20) are tightened.
Removing the guard
1. Loosen the screws (20) on the guard collar.
2. Pull up the guard (3).
Warning: Do not operate the tool when the safety
guard is not in place.
Fitting and removing a grinding (Fig. C1, C2, C3)
Warning: Do not use damaged grinding wheels.
1. Place the tool on a work bench, guard up.
2. Fit the inner flange (6) correctly onto the spindle (7)
(Fig. C1).
3. Place the disc (8) on the flange (6) (Fig.C2). When fitting
a disc with a raised center, make sure that the raised
centre (9) is facing the flange (6).
4. Screw the out flange (10) onto the spindle (7) (Fig. C3)
- the ring on the flange (10) must fae towoards the disc
when fitting a grinding disc (A)
- the ring on the flange (10) must face away from the
disc when fitting a cutting disc (B)
5. Press the spindle lock (2) and rotate the spindle (7) until
it locks in position (Fig. C2).
6. Tighten the flange (10) with the two-pin spanner
supplied.
7. Release the spindle lock.
8. To remove the disc, loosen the flange (10) with the
two-pin spanner.
Warning: Do not use a damaged disc.
Warning To minimize the danger of serious
9
ENGLISH
(Original instructions)
Mounting the side handle (Fig.D)
•
For grinding, screw the side handle (4) tightly into one of
the holes (11) or (12) on either side of the gear case.
Preparation Before Use
•
Attach the safety guard and appropriate abrasive or
grinding wheels. Do not use abrasive or grinding wheels
that are overly worn.
•
Make sure that the inner and outer flanges are attached
correctly.
•
Make sure that the abrasive or grinding wheels are
rotating in the direction of the arrows on the accessories
and tool.
Operation (Fig. F)
Instructions
Warning: Always observe the safety instructions
and applicable regulations.
Warning: To minimize the danger of serious
personal injury, please switch off the tool
power and disconnect all plugs before
adjusting or removing/installing any accessory. Before
reassembling the tool, press and release the trigger switch
to make sure the tool is already switched off.
Warning:
•
Make sure all materials to be grinded are secured in
position.
Use clamps or a vice to hold and support the workpiece to a
stable platform. It is important to clamp and support the
workpiece securely to prevent the movement of the
workpiece and loss of control. Movement of the workpiece
or loss of control may create a hazard and cause personal
injury
•
Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
by hand.
•
Support panels or any oversized workpiece to minimize
the risk of wheel pinching and kickback. Large
workpieces tend to sag under their own weight. Supports
must be placed under the workpiece near the line of cut
and near the edge of the workpiece on both sides of the
wheel.
•
Apply slight pressure to the tool. Do not apply side
pressure to the abrasive disc.
•
Avoid overloading. If the tool becomes hot, let it spin for
a few minutes with no load.
1. Be sure to hold the tool tightly with both hands (one
hand on housing, the other on side handle). Start the
tool and bring the grinding wheel on the workpiece.
10
2. Keep the edge of the wheel tilted at angle from 15 to 30
degrees against the surface of the workpiece.
3. When using a new grinding wheel, do not operate the
wheel in the B direction, otherwise, it will cut into the
workpiece. When the edge of wheel has been rounded
off, you are free to operate the grinder in either the A or B
direction.
Starting and Stopping (Fig. A)
Warning: Before using the tool, check whether the
handle is tightened securely. Check whether the
ON/OFF switch is working normally.
Before plugging in the tool to the power supply, check
whether the switch is in the OFF position when pressing the
rear end of the switch.
To start the tool, press the rear end of the switch and slide it
forward. Press the rear end of the switch to stop the tool.
Warning: Do not switch the tool on or off while
under load conditions.
Proper Hand Position (Fig. G)
Warning: To reduce the risk of serious personal
injury, ALWAYS use proper hand position as shown.
Warning: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the side handle
(figure A), with the other hand on the body of the tool, as
shown in figure G.
Switches
Caution: Hold the body of the tool firmly to maintain
control of the tool at start up and during use and
until the wheel or accessory stops rotating. Make
sure the wheel has come to a complete stop be fore laying
the tool down.
Note: To reduce unexpected tool movement, do not switch
the tool on or off while under load conditions. Allow the
grinder to run up to full speed before touching the work
surface. Lift the tool from the surface before turning the tool
off. Allow the tool to stop rotating before putting it down.
ON/OFF switch (1) Fig. A)
Warning: Before connecting the tool to a power
supply, be sure the slider switch is in the off position
by pressing the front part of the switch and
releasing. Ensure the slider switch is in the off position as
described above after any interruption in power supply to the
tool, such as the activation of a ground fault interrupter,
throwing of a circuit breaker, accidental unplugging, or power
failure.
(Original instructions)
To start the tool, slide the slider switch 1 toward the front of
the tool and press, the tool will keep running. Release
pressure from the switch and the tool will stop.
Feature of the ON/OFF switch
Slide slider switch 1 to the front of the tool and press, and
the tool will start. When releasing the switch, keep the
switch pressed down and push it to the front of the tool, and
the tool will keep running. To turn off the tool, press the front
portion of the switch to release it. The switch will spring up,
which means that the tool is in the off-state.
Explanation: Before coming into contact with the object you
are working on, make sure the abrasive wheel is turning at
maximum speed. Before turning off the tool, lift the tool up
from the object you are working on.
Caution: Make sure the abrasive wheel is
completely stopped before putting down the tool.
Rotating the Gear Case (fig. E)
The gear case is mounted onto the tool casing, and it can
be rotated to give the user a more comfortable experience
while cutting.
The rotating gear case can be turned 90 degrees, 180
degrees, and 270 degrees to the left or to the right.
• Loosen the four screws on the gear case.
• Rotate the gear case till it reaches its ideal location.
• Tighten the four screws on the gear case.
• Ensure that the rotating mechanism is locked.
Warning: Do NOT use the tool when the gear case
is unlocked.
Application on Metals
When applying the tool on metals, make sure that a
residual-current device (RCD) is inserted to prevent danger
from metal chips.
If the RCD causes power disconnection, have the tool sent
to an authorized STANLEY dealer for repair.
Warning: Under extreme working conditions,
conductive dust and grit may accumulate on the
housing interior when handling metal workpieces. This could
create an electric shock hazard as it weakens the protective
insulation in the grinder.
To avoid accumulation of metal chips in the interior of the
grinder, we recommend cleaning the ventilation ducts daily.
Refer to Maintenance.
Using Grinding Wheels
Warning: Metal powder accumulates. Excessive
use of the grinding wheel on metals may increase
ENGLISH
the risk of electric shock. To reduce the risk, insert the RCD
before use and clean the ventilation ducts daily. Follow the
maintenance instructions below to blow dry compressed air
into the ventilation ducts.
Maintenance
STANLEY power tools have been designed to operate over
a long period of time with minimal maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
Warning: To minimize the danger of serious
personal injury, please switch off the tool power and
disconnect all plugs before adjusting or
removing/installing any accessory. Before reassembling
the tool, press and release the trigger switch to make sure
the tool is already switched off.
Lubrication
This power tool does not require separate lubrication.
Cleaning
Warning: Once visible dust accumulates on the
ventilation ducts and the surrounding, immediately
use dry air to blow away dust and grit out of the
interior of the housing. You need to wear approved eye and
facial protective gear when performing this process.
Warning: Never use solvents or harsh chemicals to
clean non-metal parts of the tool. These chemicals
may weaken the material of the parts. Use only mild soap
and damp cloth to clean the tool. Never let any liquid get
inside the tool; never immerse any part of the tool into liquid.
Accessories
Warning: Excluding accessories provided by
STANLEY, all other accessories have not been
tested for product compatibility. Using such accessories
together with this tool may cause safety hazards. To
minimize the risk of personal injury, we recommend you to
use only STANLEY accessories with this product. Please
inquire at your dealer for more information regarding suitable
accessories.
11
ENGLISH
(Original instructions)
Remarks
Service Information
•
STANLEY's policy is one of continuous improvement to
our products and as such, we reserve the right to
modify product specifications without prior notice.
•
Standard equipment and accessories may vary by
country.
STANLEY offers a full network of authorized service
locations. All STANLEY Service Centers are staffed with
trained personnel to provide customers with efficient and
reliable power tool service. For more information about our
authorized service centers and if you need technical advice,
repair, or genuine factory replacement parts, contact the
STANLEY location nearest you.
•
Product specifications may differ by country.
One year warranty
•
Complete product range may not be available in all
countries. Contact your local STANLEY dealers for
range availability.
If your STANLEY product becomes defective due to faulty
materials or workmanship within 12 months from the date of
purchase, STANLEY guarantees to replace all defective
parts free of charge or – at our discretion – replace the unit
free of charge provided that:
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
•
The product has not been misused and has been used in
accordance with the instruction manual.
Should you find one day that your STANLEY product needs
replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
•
The product has been subject to fair wear and tear;
•
Repairs have not been attempted by unauthorised
persons;
•
Proof of purchase is produced.
•
The STANLEY product is returned complete with all
original components
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent environmental
pollution and reduces the demand for raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
STANLEY provides a facility for the collection and recycling
of STANLEY products once they have reached the end of
their working life. To take advantage of this service please
return your product to any authorised repair agent who will
collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Stanley office at the address
indicated in this manual. Alternatively, a list of authorised
STANLEY repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com
12
If you wish to make a claim, contact your seller or check the
location of your nearest authorised STANLEY repair agent in
the STANLEY catalogue or contact your local STANLEY
office at the address indicated in this manual. A list of
authorised STANLEY repair agents and full details of our
after sales service is available on the internet
at:www.stanleytools.com
N434934
04/2015
Names & Addresses for STANLEY Service Concessionaries - MIDDLE EAST & AFRICA
ALGERIA: Sarl Outillage Corporation, 08 Rue Med Boudiaf - Cheraga - Algiers, Algeria. Tel: (213-21) 375130, Fax: (213-21) 369667. ANGOLA: Angoferraria,
Lda., Rua Robert Shields, No. 61, Luanda, Angola, Tel: 00244-222-395837 / 222-395034, Fax: 00244-222-394790. AZERBAIJAN: Royalton Holdings Ltd. 41
Khagani St. Apt. 47 AZ 1001, Baku. Tel: (994-12) 4935544, Fax: (994-12) 5980378. BAHRAIN: Kavalani & Sons W.L.L., P.O. Box 71, Sitra, Manama, Tel: (973)
17732888, Fax: (973) 17737379. Alfouz Services Co. WLL., P.O. Box 26562, Tubli, Manama. Tel: (973) 17783562, Fax: (973) 17783479. EGYPT: El Farab
S.A.E., 15-Nabil El Wakkad Street, Dokki, Giza, Egypt, Tel: 00202-37603946 / 002-010-2582544, Fax: 00202-33352796. ETHIOPIA: Seif Tewfik Sherif, Arada
Sub-City, Kebele 01/02, Global Insurance Building, 2nd Floor, Room 43, P.O. Box 2525, Addis Ababa, Ethiopia. Tel: (251-11) 1563968/ 1563969, Fax: (251-11)
1558009. IRAQ: Financial Links, Kazzaz Building Arasat Al-Hindia Block No: 629 Street: 31Building No: 1 Baghdad – Iraq. Tel: 00964 (0)780 195 2223/ 00964
(0)781 3763044. Al Sard Co. for General Trading Ltd. Jbara Bldg. 3Flr, Al Rasheed St. Bagdad. Tel: (964) 18184102. Sakhar Group, Arrassat al-hindya Al
Masbah, Bagdad. (964) 7400144446. JORDAN: Palestine Bldg. Matl. (Bashiti Hardware), 93 King Abdullah 2nd Street, Opp. ELBA House, P.O. Box 3005,
Amman 11953, Tel: (962-6) 5349098, Fax: (962-6) 5330731. KENYA: Dextron Tools Ltd., P.O. Box 20121-00200, Shariff House, Kimathi Street, Nairobi. Tel:
(254-20) 6905000/ 2358021, Fax: (254-20) 6905111/ 6905112. KUWAIT: Al Omar Technical Co., P.O. Box 4062, 13041 Safat, Kuwait. Tel: (965) 24848595/
24840039, Fax: (965) 24845652. Fawaz Al Zayani Establishment, P.O. Box 42426, Shop No. 18, Al Humaizi Commercial Complex, Khalifa Al Jassim,
Shuwaikh, Kuwait. Tel: (965) 24828710, Fax: (965) 24828716. Fawaz Al Zayani Establishment, P.O. Box 42426, Shop No.18, Al Humaizi Commercial
Complex, Khalifa Al Jassim, Shuwaikh, Kuwait, Tel: (965) 24828710, Fax: (965) 24828716. Fawaz Al Zayani Establishment, Fahaheel Industrial Area, Main St.,
Sanaya, Kuwait, Tel: (965) 23925830, Fax: (965) 24828716. LEBANON: Est. Shaya & Azar S.A.R.L., Boulvard Jdeideh - Mar Takla - Bouchrieh .P.O. Box
90545 Jdeideh.Beirut - Lebanon, Tel: 00961 1 872305 / 306 , Fax: 00961 1 872303. LIBYA: North Africa Trading ( El Ghoul Brothers), AlHilal Service Center
Tawergha St. Misurata, Tel: 00218-091-3221408. (Benghazi) Sniydel st., Amr Ibn EL-Aas Rd. Tel: (+218) 92 5771120. (Tripoli) Al Barniq Service Center,
Mokhazin elsukar st., ElFallah. Tel: (+218) 21 4808019. (Misrata) Al Hilal Service Center, Tawergha st. Tel: (+218) 51 2626743. MAURITIUS: Robert Le Marie
Limited, Old Moka Road, Bell Village, P.O. Box 161, Port Louis, Tel: 00230-212 1865/ 212 2847, Fax: 00230-2080843. MOROCCO: Ets Louis Guillaud & Cie,
149, Quartier Industriel, Moulay Rachid, Casablanca, Postal Code 20450, Morocco, Tel: 00212-522729233, Fax: 00212-522729096. NIGERIA: Meridian
Power Tools Ltd., Gr.Floor, #1 Alhaji Masha Rd, Next toTeslim Balogun Stadium, Near National Stadium Surulere, Lagos, Nigeria, Tel: 00234-1-7740431 /
7740410, Fax: 00234-1-7913798. OMAN: Al Jizzi Company LLC, P.O. Box 1704,PC 112 Ruwi, Oman, Tel: (968) 24832618/ 24835153, Fax: (968)
24831334/24836460. Al Hassan Technical & Construction Supplies Co. LLC, P.O. Box 1948, P.C. 112, Ruwi, Tel: (968) 24810575 / 24837054, Fax: (968)
24810287/ 24833080. Oman Hardware Co. LLC, P.O. Box 635, Ruwi Postal Code 112, Te: (968) 24815131, Fax: (968) 24816491. Khimji Ramdas, P.O. Box
19, Post Code 100, Ghala, Muscat, Oman. Tel: (968) 24595906/ 907, Fax: (968) 24852752. Oman Marketing & Service Co. (Omasco), P.O. Box 2734, Behind
Honda Showroom, Wattayah, Oman. Tel: (968) 24560232/ 24560255, Fax: (968) 24560993. Oman Marketing & Service Co. (Omasco), Al Ohi, Sohar, Oman.
Tel: (968) 26846379, Fax: (968) 26846379. Oman Marketing & Service Co. (Omasco), Sanaya, Salalah, Oman. Tel: (968) 23212290, Fax: (968) 23210936.
PAKISTAN: ZIT Co - Nasir & Bros., 2nd Floor, Qadri Center, Chowk Dalgran Railway Road, Lahore, Pakistan, Tel: 0092 42 37670839, Fax: 0092 42
37652989. Ammar Service & Spares, 60-Bank Arcade, Serai Road, Karachi, Pakistan. Tel: (92-21) 32426905, Fax: (92-21) 32427214. QATAR: Teyseer
Industrial Supplies & Services Co. WLL, 55, Al Wakalat St. (Between St. 18 & 19) Salwa Industrial Area, P.O. Box 40523 Doha,Qatar, Te: (974) 44581536, Fax:
(974) 44682024. Shaheen Electrical Works & Trading Co. WLL, Gate 34, St. 44 Industrial Area P.O. Box 9756, Doha, Tel: (974) 44600230 /44600525, Fax:
(974) 44601338. Al Muftah Service Centre, Al Wakrah Road, P.O. Box 875, Doha,Qatar, Tel: (974) 44650880/ 44650110/ 44446868, Fax: (974) 44441415 /
44662599. SAUDI ARABIA: (Al Bahr) Mohamed Ahmed Bin Afif Est., P.O. Box 530, Yanbu, Al Bahr. Tel: (966-4) 3222626/ 3228867, Fax: (966-4) 3222210.
(Al Khobar) Fawaz Ebrahim Al Zayani Trading Est., P.O. Box 76026, Al Khobar # 31952, Tel: (966-3) 8140914, Fax: (966-3) 8140824. MSS (Al-Mojil Supply &
Services) P.O. Box 450, Jubail 31951, Opp. Gulf Bridge Library & Riyadh House. Tel: (966-3) 3612850/ 3624487/ 3621729, Fax: (966-3) 3623589/ 3620783.
(Dammam) MSS (Al-Mojil Supply & Services), P.O. Box 450, Jubail 31951.Opp-Gulf Bridge Library & Riyadh House, Tel: (966-3) 3612850 / 3624487 /
3621729, Fax: (966-3) 3623589 / 3620783. Al Bawardi Tools & Hardware, P.O. Box 112, Dammam, Tel: (966-3) 8330780 Ext.24 / 8348585 Ext. 24 /
+966-3-8335555, Fax: (966-3) 8336303. (Al Hassa) Mutawa Trading & Gen. Services, Maliki road Hafuf city, Al Hassa, KSA. Tel: (966) 502846275 (Jeddah) Al
Bawardi Tools & Hardware, P.O. Box 16905, Jeddah 21474, Tel: (966-2) 6444547 / 6439035 / 6456095, Fax: (966-2) 6439024. EAC (Al Yousef Contg. & Trdg.
Est.), P.O. Box 30377, Jeddah -21477, Tel: (966-2) 6519912, Fax: (966-2) 6511153. (Madina) Garziz Trading for Bldg Mat & Decoration, P.O. Box 3364,
Madina, Tel: (966-4) 826 14 90 / 8227636, Fax: (966-4) 8265741. (Riyadh) Industrial Material Organization (IMO), P.O. Box 623, Rail Street ,Riyadh, Tel:
(966-1) 4028010 Ext 26 / 8001245757, Fax: (966-1) 4037970. Sultan Garment Factory (RSC), P.O. Box 29912, Riyadh 11467, KSA, Tel: (966-1) 4055148 /
4042889, Fax: (966-1) 4055148. Al Bawardi Tools & Hardware, P.O. Box 68, Riyadh 11411, Tel: (966-1) 4484999, Fax: (966-1) 4487877. (Yanbu) Fawaz
Ebrahim Al Zayani, Opposite to Al Fouzan, Jeddah highway or King Abdul Aziz road, Yanbu. Tel: (966-4) 3960980, Fax: (966-4) 3961980. Mohamed Ahmed
Bin Afif Est., P.O. Box 530, Yanbu, Al Bahr, Tel: (966-4) 3222626/ 3228867, Fax: (966-4) 3222210. SOUTH AFRICA: Stanley Black & Decker - RSA, 199
Winze Drive Stormill Ext 9 Roodepoort, Tel: (2711) 472 0454, Fax: (2711) 472 0482. Trevco Power Tool Service 14 Steenbok Street, Koedoespoort, 0186,
Pretoria, South Africa. Tel: (27-86) 1873826, Fax: (27-86) 5001771. TANZANIA: General Motors investment Ltd., P.O. Box 16541, 14 Nyerere Road,
Vingunguti, Dar-es-Salaam. Tel: (255 22) 2862661/ 2865022, Fax: (255 22) 2862667. TUNISIA: Societe Tunisienne De Maintenance (STM), Rue de la
Physique. Nouvelle Zone Industrielle Ben Arous., 2013 Ben Arous, Tunisia. Tel: (+216) 79 389687, Fax: (+216) 71 385154. UAE: (Abu Dhabi) Light House
Electrical, P.O. Box 120, Abu Dhabi, Tel: (971-2) 6726131, Fax: (971-2) 6720667. Galaxy Equipment Trading, Madinath Zayed (Baada Zaid), Abu Dhabi P.C.
58910, Tel: (971-2) 8844279, Fax: (971-2) 8844297 (Ajman) Al Sukoon Gen. Trdg. Co. LLC, P.O. Box 2975, Ajman. Tel: (971-6) 7435725/ 7438317, Fax:
(971-6) 7437350. Al Sukoon Gen. Trdg. Co. LLC, P.O. Box 2975, Ajman, Tel: (971-6) 7435725 / 7438317, Fax: (971-6) 7437350 (Al Ain) Zillion Equipment and
Spare Parts Trading LLC, P.O. Box 19740, Opp. Bin Sadal/ Trimix Redymix Sanaiya, Al Ain. Tel: (971-3) 7216690, Fax: (971-3) 7216103. (Dubai) Black &
Decker (Overseas) GmbH, P.O. Box 5420, Dubai, Tel: (971-4) 8127400/ 8127406, Fax: (971-4)2822765. Ideal Star Workshop Eqpt.Trading LLC, P.O. Box
37116, Al Quoz, Dubai, Tel: (971-4) 3474160, Fax: (971-4) 3474157, Fine Tools, P.O.Box 30139 , Al Quoz, Dubai, Tel: (971-4) 3385240, Fax: (971-4) 3385239,
Alebrah Engineering Service, P.O. Box 78954, Al Qusais , Dubai, Tel: (971-4) 2850044, Fax: (971-4) 2844802. (Musaffah) Light House Electrical, P.O. Box
120, Abu Dhabi, Tel: (971-2) 5548315, Fax: (971-2) 5540461. (Sharjah) Mc Coy Middle East LLC, P.O. Box 25793, Sharjah, Tel: (971-6) 5395931, Fax:
(971-6) 5395932. Burj Al Madeena, Industrial Area No.1, Opp. Pakistani Masjid, P.O. Box 37635, Sharjah. Tel: (971-6) 5337747, Fax: (971-6) 5337719. Burj Al
Madeena, , Industrial Area No 1,opp Pakistani Masjid P.O. Box 37635, Sharjah, Tel: (971-6) 5337747, Fax: (971-6) 5337719 (Ras Al Khaimah) Mc Coy Middle
East LLC, P.O. Box 10584, Ras Al Khaimah, Tel: (971-7) 2277095, Fax: (971-7) 2277096. UGANDA: The Building Center (U) Ltd., 52 Station Road, Kitgum
House, P.O. Box 7436, Kampala, Uganda. Tel: (256-41) 4234567/ 4259754, Fax: (256-41) 4236413. YEMEN: (Aden) Middle East Trad. Co. Ltd. (METCO),
Mualla Dakka, Aden, Yemen. Tel: (967-2) 222670, Fax: (967-2) 222670. (Sana'a) Middle East Trad. Co. Ltd. (METCO), Hayel St., Sana'a, Yemen. Tel: (967-1)
204201, Fax: (967-1) 204204. (Taiz) Middle East Trading Co. (METCO), P.O. Box 12363, 5th Flr, Hayel Saeed Anam Bldg, Al-Mugamma St. Taiz, Yemen. Tel:
(967-4) 213455, Fax: (967-4) 219869.
Download PDF