BDCH188 | Black&Decker BDCH188 HAMMER DRILL Type H1 instruction manual

www.blackanddecker.com.au
www.blackanddecker.co.nz
BDCH188
A
B
C
D
E
2
(Original instructions)
Intended use
Your BLACK+DECKER BDCH188 - Hammer Drill has
been designed for drilling in wood, metal, plastics, and
masonry as well as for screwdriving applications. This tool
is intended for consumer use only.
Safety instructions
General power tool safety warnings
@
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings
and instructions listed below may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference. The term "power tool" in all of the warnings listed
below refers to your mains operated (corded) power tool
or battery operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while
operating a power tool. Distractions can cause you
to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
ENGLISH
c. Do not expose power tools to rain or wet
conditions. Water entering a power tool will increase
the risk of electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools may
result in serious personal injury.
b. Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
c. Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch
on invites accidents.
d. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result
in personal injury.
e. Do not overreach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations.
3
ENGLISH
(Original instructions)
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust
collection can reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before
making any adjustments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power tools
operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
4
different from those intended could result in a
hazardous situation.
5. Battery tool use and care
a.
manufacturer. A charger that is suitable for one type
b.
with another battery pack.
designated
battery packs. Use of any other battery packs may
c. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws, or other small metal objects, that
can make a connection from one terminal to
another. Shorting the battery terminals together may
d. Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or
burns.
6. Service
a.
repair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained.
b. Power to the tool should always be supplied via
residual current device with a rated residual current of
30mA or less.
@
Additional power tool safety warnings
u
u
Warning! Additional safety warnings for
screwdrivers and impact wrenches
Wear ear protectors when impact drilling. Exposure
to noise can cause hearing loss.
Use auxiliary handle(s) if supplied with the tool.
Loss of control can cause personaly.injur
(Original instructions)
u
u
u
Hold power tool by insulated gripping surfaces,
when performing an operation where the fastener
may contact hidden wiring. Fasteners contacting a "live" wire may make exposed metal parts of
the power tool "live" and could give the operator an
electric shock.
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
Never use a chisel accessory in rotary mode. The
accessory will bind in the material and rotate the drill.
u
u
u
the location of wiring and pipes.
Avoid touching the tip of a drill bit just after drilling, as
it may be hot.
The intended use is described in this instruction
manual. The use of any accessory or attachment or
performance of any operation with this tool other than
those recommended in this instruction manual may
present a risk of personal injury and/or damage to
property.
Safety of others
u
u
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do
not play with the appliance.
Residual risks.
Additional residual risks may arise when using the tool
which may not be included in the enclosed safety warnings. These risks can arise from misuse, prolonged use
etc.
ENGLISH
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving parts.
u Injuries caused when changing any parts, blades or
accessories.
u Injuries caused by prolonged use of a tool. When
using any tool for prolonged periods ensure you take
regular breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Vibration
The declared vibration emission values stated in the
technical data and the declaration of conformity have been
measured in accordance with a standard test method
provided by EN 60745 and may be used for comparing
one tool with another. The declared vibration emission
value may also be used in a preliminary assessment of
exposure.
Warning! The vibration emission value during actual
use of the power tool can differ from the declared value
depending on the ways in which the tool is used. The
vibration level may increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons
regularly using power tools in employment, an estimation
of vibration exposure should consider, the actual conditions of use and the way the tool is used, including taking
account of all parts of the operating cycle such as the
times when the tool is switched off and when it is running
idle in addition to the trigger time.
5
Labels on tool
The following symbols are shown on the tool along with
the date code:
:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Additional safety instructions for batteries and
chargers (Not provided with the tool
Batteries
u Never attempt to open for any reason.
u Do not expose the battery to water.
u Do not store in locations where the temperature may
exceed 40 °C.
u Charge only at ambient temperatures between 10 °C
and 40 °C.
u Charge only using the charger provided with the tool.
u When disposing of batteries, follow the instructions
given in the section "Protecting the environment".
p
Do not attempt to charge damaged batteries.
Chargers
u Use your BLACK+DECKER charger only to charge
the battery in the tool with which it was supplied. Other
batteries could burst, causing personal injury and
damage.
u Never attempt to charge non-rechargeable batteries.
u Have defective cords replaced immediately.
u Do not expose the charger to water.
u Do not open the charger.
u Do not probe the charger.
$
+
6
The charger is intended for indoor use only.
Read the instruction manual before use.
Electrical safety
#
u
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on
the rating plate. Never attempt to replace the
charger unit with a regular mains plug.
If the supply cord is damaged, it must be replaced by
the manufacturer or an authorised BLACK+DECKER
Service Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Forward/reverse slider
3. Mode selector / torque adjustment collar
4.Chuck
5. Speed selector
6. Bit holder
Fig. A (not included, sold separately)
7.Battery
8.Charger
9. Charge Indicator
Assembly
Warning! Before assembly, remove the battery from the
tool.
Fitting and removing the battery (fig. B)
To fit the battery (7), line it up with the receptacle on
the tool. Slide the battery into the receptacle and push
until the battery snaps into place.
u To remove the battery, push the release button (10)
while at the same time pulling the battery out of the
receptacle.
u
Fitting and removing a drill bit or screwdriver bit
This tool is fitted with a keyless chuck to allow for an easy
exchange of bits
u Lock the tool by setting the forward/reverse slider (2)
to the centre position.
(Original instructions)
Open the chuck (4) by turning the front part with one
hand while holding the rear part with the other.
u Insert the bit shaft into the chuck and firmly tighten the
chuck.
This tool is supplied with a double-ended screwdriver bit in
the bit holder (6).
u To remove the screwdriver bit from the bit holder, lift
the bit from the recess.
u To store the screwdriver bit, firmly push it into the
holder.
u
Use
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Charging the battery (fig. A)
The battery needs to be charged before first use and
whenever it fails to produce sufficient power on jobs that
were easily done before. The battery may become warm
while charging; this is normal and does not indicate a
problem.
Warning! Do not charge the battery at ambient temperatures below 10 °C or above 40 °C. Recommended
charging temperature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above
40 °C.
The battery should be left in the charger and the
charger will begin to charge automatically when the
cell temperature warms up or cools down.
u To charge the battery (7), insert it into the charger (8).
The battery will only fit into the charger in one way. Do
not force. Be sure that the battery is fully seated in the
charger.
u Plug in the charger and switch on at the mains.
The charging indicator (9) will blink.
The charge is complete when the charging indicator (9)
switches to continuously on. The charger and the battery
can be left connected indefinitely. The LED will switch on
as the charger occasionally tops up the battery charge.
u
ENGLISH
Charge discharged batteries within 1 week. Battery
life will be greatly diminished if stored in a discharged
state.
Leaving the battery in the charger
The charger and battery pack can be left connected with
the LED glowing indefinitely. The charger will keep the
battery pack fresh and fully charged.
Selecting the direction of rotation (fig. C)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
u To select forward rotation, push the forward/reverse
slider (2) to the left.
u To select reverse rotation, push the forward/reverse
slider to the right.
u To lock the tool, set the forward/reverse slider into the
centre position.
Selecting the operating mode or torque (fig. D)
This tool is fitted with a collar to select the operating mode
and to set the torque for tightening screws. Large screws
and hard workpiece materials require a higher torque setting than small screws and soft workpiece materials. The
collar has a wide range of settings to suit your application.
u For drilling in wood, metal and plastics, set the collar
(3) to the drilling position by aligning the symbol with
the marking.
u For screwdriving, set the collar to the desired setting.
If you do not yet know the appropriate setting, proceed
as follows:
u Set the collar (3) to the lowest torque setting.
u Tighten the first screw.
u If the clutch ratchets before the desired result is
achieved, increase the collar setting and continue
tightening the screw. Repeat until you reach the
correct setting. Use this setting for the remaining
screws.
7
Drilling in masonry (fig. D & E)
u For drilling in masonry, set the collar (3) to the hammer drilling position by aligning the symbol with the
marking.
u Slide the speed selector (5) towards the front of the
tool (2nd gear).
Speed selector (fig. E)
u For drilling in steel and for screwdriving applications,
slide the speed selector (5) towards the rear of the tool
(1st gear).
u For drilling in materials other than steel, slide the
speed selector (5) towards the front of the tool (2nd
gear).
Drilling/screwdriving
Select forward or reverse rotation using the forward/
reverse slider (2).
u To switch the tool on, press the switch (1). The tool
speed depends on how far you press the switch.
u To switch the tool off, release the switch.
Screwdriving
Always use the correct type and size of screwdriver
bit.
u If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
u Always hold the tool and screwdriver bit in a straight
line with the screw.
u
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
u
Hints for optimum use
Drilling
Always apply a light pressure in a straight line with the
drill bit.
u Just before the drill tip breaks through the other side of
the workpiece, decrease pressure on the tool.
u Use a block of wood to back up workpieces that may
splinter.
u Use spade bits when drilling large diameter holes in
wood.
u Use HSS drill bits when drilling in metal.
u Use masonry bits when drilling in soft masonry.
u Use a lubricant when drilling metals other than cast
iron and brass.
u Make an indentation using a centre punch at the
centre of the hole to be drilled in order to improve
accuracy.
u
8
Warning! Before performing any maintenance on the
tool, remove the battery from the tool. Unplug the charger
before cleaning it.
u Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
u Regularly open the chuck and tap it to remove any
dust from the interior.
Protecting the environment
Z
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your BLACK+DECKER
product needs replacement, or if it is of no further use to
you, do not dispose of it with household waste. Make this
product available for separate collection.
z
Separate collection of used products and
packaging allows materials to be recycled and
used again.
Re-use of recycled materials helps prevent environmental pollution and reduces the demand
for raw materials.
ENGLISH
(Original instructions)
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Technical data
BDCH188 (H1)
Voltage
BLACK+DECKER provides a facility for the collection and
recycling of BLACK+DECKER products once they have
reached the end of their working life. To take advantage of
this service please return your product to any authorised
repair agent who will collect them on our behalf.
VDC
-1
18
No-load speed
Min
Max. torque
Nm
17/38
Chuck capacity
mm
10
0-400/0-1350
You can check the location of your nearest authorised
repair agent by contacting your local BLACK+DECKER
Max drilling capacity
Steel/wood/masonry
mm
10/25/10
a list of authorised BLACK+DECKER repair agents and
full details of our after-sales service and contacts are
available on the Internet at: www.2helpU.com
Weight
kg
1.4
Batteries
Z
u
Level of sound pressure according to EN 60745:
Sound pressure (LpA) 84.7 dB(A), uncertainty (K) 3 dB(A)
Sound power (LWA) 98.4 dB(A), uncertainty (K) 3 dB(A)
There are no user servicable parts inside.
At the end of your products life return the whole unit
to your service agent or to a local recycling station to
have the battery recycled. Do not throw the unit out
with household waste.
Vibration total values (triax vector sum) according to EN 60745:
Hammer Drilling into concrete (ah,HD) 9.4 m/s2, uncertainty (K) 1.5 m/s2
Drilling into metal (ah,D) 0.8 m/s2, uncertainty (K) 1.5 m/s2
Screwdriving without impact (ah) 0.5 m/s2, uncertainty (K) 1.5 m/s2
9
Australia & New Zealand
Stanley Black & Decker
82 Taryn Drive, Epping, VIC 3076 Australia
www.blackanddecker.com.au
www.blackanddecker.co.nz
Tel.1800 338 002 (Aust) or Tel. 0800 339 258 (NZ)
90620228
04/2015
Download PDF