STCD1081B2 | Stanley STCD1081B2 DRILL/DRIVER instruction manual

STCD1081B2
English
Page 4
ENGLISH
(Original instructions)
9
FIG. A
2
FIG. B
(Original instructions)
FIG. C
ENGLISH
FIG. D
FIG. E
3
ENGLISH
(Original instructions)
Intended use
Your Stanley drill/screwdriver has been designed for
screwdriving applications and for drilling in wood, metal and
plastics.
Safety instructions
General power tool safety warnings
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below
refers to your mains operated (corded) power tool or battery
operated (cordless) power tool.
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric
shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
iii. Personal safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
b. Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
i. Work area safety
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
ii. Electrical safety
a. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of
electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
4
c. Prevent unintentional starting. Ensure the switch is
in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch on
invites accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
e. Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
(Original instructions)
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
iv. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source before
making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc., in
accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions and
the work to be performed. Use of the power tool for
operations different from those intended could result in a
hazardous situation.
b. Use Power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
c. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws, or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
d. Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
vi. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is
maintained.
Additional power tool safety warnings
Warning! Additional safety warnings for drills and
impact drills
•
Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
•
Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
•
Hold power tool by insulated gripping surfaces when
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory
contacting a "live" wire may make exposed metal parts of
the power tool "live" and could give the operator an
electric shock.
•
Hold power tool by insulated gripping surfaces when
performing an operation where the fastener may
contact hidden wiring. Fasteners contacting a "live"
wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
•
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body leaves it unstable
and may lead to loss of control.
v. Battery tool use and care
a. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
ENGLISH
5
ENGLISH
(Original instructions)
•
Before drilling into walls, floors or ceilings, check for
thelocation of wiring and pipes.
tool with another. The declared vibration emission value may
also be used in a preliminary assessment of exposure.
•
Avoid touching the tip of a drill bit just after drilling, as it
may be hot.
•
This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children should be supervised to ensure
that they do not play with the appliance.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level
may increase above the level stated.
•
The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those
recommended in this instruction manual may present a
risk of personal injury and/or damage to property.
Safety of others
•
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons
regularly using power tools in employment, an estimation of
vibration exposure should consider, the actual conditions of
use and the way the tool is used, including taking account of
all parts of the operating cycle such as the times when the
tool is switched off and when it is running idle in addition to
the trigger time.
Labels on tool
The label on your tool may include the following symbols:
Read
Instructions
Manual
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
•
Use Eye
Protection
Use Ear
Protection
Children should be supervised to ensure that they do not
play with the appliance.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc. Even with
the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks can
not be avoided. These include:
•
Injuries caused by touching any rotating/moving parts.
•
Injuries caused when changing any parts, blades or
accessories.
•
Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
•
Impairment of hearing.
•
Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Vibration
The declared vibration emission values stated in the
technical data and the declaration of conformity have been
measured in accordance with a standard test method
provided by EN 60745 and may be used for comparing one
6
V ........ Volts
A ........ Amperes
Hz ....... Hertz
...... Class II
Construction
W ........ Watts
....
Earthing
Terminal
....
Safety Alert
Symbol
.../min..
Revolutions
or Reciprocation per
minute
min ..... minutes
..... Alternating
Current
..... Direct
Current
n 0 ....... No-Load
Speed
Position of date barcode
The Date Code, which also includes the year of
manufacture, is printed into the housing.
Example:
2014 XX JN
Year of manufacturing
Additional safety instructions for batteries
and chargers
Batteries
•
Never attempt to open for any reason.
•
Do not expose the battery to water.
•
Do not store in locations where the temperature may
exceed 40 °C.
•
Charge only at ambient temperatures between 10 °C
and 40 °C.
•
Charge only using the charger provided with the tool.
•
When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
(Original instructions)
Do not attempt to charge damaged batteries.
Chargers
•
Use your STANLEY charger only to charge the battery in
the tool with which it was supplied. Other batteries could
burst, causing personal injury and damage.
•
Never attempt to charge non-rechargeable batteries.
•
Have defective cords replaced immediately.
•
Do not expose the charger to water.
•
Do not open the charger.
•
Do not probe the charger.
Assembly
Warning! Before assembly, remove the battery from the tool.
Fitting and removing the battry (FIG. C)
•
To fit the battery (5), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
•
To remove the battery, push the release buttons (12)
while at the same time pulling the battery out of the
receptacle.
Fitting and removing a drill bit or screwdriver
bit (FIG. D)
This tool is fitted with a keyless chuck to allow for an easy
exchange of bits.
The charger is intended for indoor use only.
•
Lock the tool by setting the forward/reverse slider (2) to
the centre position.
Read the instruction manual before use.
•
Grasp the chuck (3) and rotate it in the counterclockwise
direction, as viewed from the chuck end.
•
Insert the bit shaft (13) into the chuck.
•
Firmly tighten the chuck by rotating it in the clockwise
direction as viewed from the chuck end.
Electrical safety
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on the
rating plate. Never attempt to replace the charger unit with a
regular mains plug.
•
ENGLISH
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised STANLEY Service Centre
in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Forward/reverse slider
3. Chuck
4. Torque adjustment collar
5. Battery
Warning! Do not attempt to tighten drill bits (or any other
accessory) by gripping the front part of the chuck and turning
the tool on. Damage to the chuck and personal injury may
occur when changing accessories in this manner.
Use
Warning! Let the tool work at its own pace. Do not overload.
Charging the battery (FIG. A)
The battery needs to be charged before first use and
whenver it fails to produce sufficient power on jobs that were
easliy done before. The battery may become warm while
charging; this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
8. Magnetic bit holder
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40
°C. The battery should be left in the charger and the
charger will begin to charge automatically when the cell
temperature warms up or cools down.
FIG. A
•
To charge the battery (5), insert it into the charger (10).
The battery wii only fit into the charger in one way. Do
not force.. Be sure that the battery is fully seated in the
charger.
•
Plug in the charger and switch on at the mains.
6. LED work light
7. Speed selector
9. Charger
10. Charging indicator
7
ENGLISH
(Original instructions)
The charging indicator (11) will flash green continuously
(slowly).
•
To select reverse rotation, push the forward/reverse
slider to the right.
The charge is complete when the charging indicator (11)
lights green continuously. The charger and the battery can
be left connected indefinitely with the LED illuminated. The
LED will change to flashing green (charging) state as the
charger occasionally tops up the battery change. The
charging indicator (11) will be lit as long as the battery is
connected to the plugged-in charger.
•
To lock the tool, set the forward/reverse slider into the
centre position.
•
Charge discharged batteries within 1 week. Battery life
will be greatly diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery
pack fresh and fully charged.
Selecting the torque
This tool is fitted with a collar to set the torque for various
screwdriving and drilling applications. Large screws and hard
workpiece materials require a higher torque setting than
small screws and soft workpiece materials. For the definition
of the symbol refer to the listing below.
•
For drilling in wood, metal and plastics, set the torque
adjustment collar (4) to the symbol.
•
For screwdriving, set the collar to the desired setting. If
you do not yet know the appropriate setting, proceed as
follows:
Charger diagnostics
If the charger detects a weak or damaged battery, the
charging indicator (11) will flash red at a fast rate. Proceed
as follows:
•
Re-insert the battery (5).
•
If the charging indicators continues flashing res at a fast
rate, use a different battery to determine if the charging
process works properly.
•
If the replaced battery charges correctly, the original
battery is defective and should be returned to a service
centre for recycling.
•
If the new battery gives the same indication as the
original battery, take the charger to be tested at an
authorised service centre.
-
Set the torque adjustment collar (4) to the lowest
torque setting.
-
Tighten the first screw.
-
If the clutch ratchets before the desired result is
achieved, increase the collar setting and continue
tightening the screw. Repeat until you reach the
correct setting. Use this setting for the remaining
screws.
Speed selector
•
For drilling in steel and for screwdriving applications,
slide the speed selector (8) towards the rear of the tool
(1st gear).
•
For drilling in materials other than steel, slide the speed
selector (8) towards the front of the tool (2nd gear).
Drilling/screwdriving
Note: It may take as long as 60 minutes to determine
that the battery is defective. If the battery is too hot or
too cold, the LED will alternately blink red, fast and
slow, one flash at each speed and repeat
•
Select forward or reverse rotation using the
forward/reverse slider (2).
•
To switch the tool on, press the switch (1). The tool
speed depends on how far you press the switch.
Selecting the direction of rotation (FIG. E)
•
To switch the tool off, release the switch.
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
LED work light
•
To select forward rotation, push the forward/reverse
slider (2) to the left.
8
The LED work light (7) is activated automatically when the
trigger is depressed. The LED work light will illuminate when
the trigger is partially depressed, before the unit begins
running.
(Original instructions)
ENGLISH
Hints for optimum use
Notes
Drilling
•
STANLEY's policy is one of continuous improvement to
our products and, as such, we reserve the right
tochange product specifications without prior notice.
•
Standard equipment and accessories may vary by
country.
•
Product specifications may differ by country.
•
Complete product range may not be available in all
countries.
Contact your local STANLEY dealers for range
availability.
•
Always apply a light pressure in a straight line with the
drill bit.
•
Just before the drill tip breaks through the other side of
the workpiece, decrease pressure on the tool.
•
Use a block of wood to back up workpieces that may
splinter.
•
Use spade bits when drilling large diameter holes in
wood.
•
•
Use HSS drill bits when drilling in metal.
Batteries
•
Use masonry bits when drilling in soft masonry.
•
Use a lubricant when drilling metals other than cast iron
and brass.
•
Make an indentation using a centre punch at the centre
of the hole to be drilled in order to improve accuracy.
Screwdriving
•
Always use the correct type and size of screwdriver bit.
•
If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
•
Always hold the tool and screwdriver bit in a straight line
with the screw.
Maintenance
Your STANLEY tool has been designed to operate over a
long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
•
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
•
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
•
Regularly open the chuck and tap it to remove any dust
from the interior.
Run the battery down completely, then remove it
from the tool.
•
NiCd, NiMH and Li-Ion batteries are recyclable. Take
them to any authorised repair agent or a local recycling
station.
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Stanley product needs
replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for raw
materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Stanley provides a facility for the collection and recycling of
Stanley products once they have reached the end of their
working life. To take advantage of this service please return
your product to any authorised repair agent who will collect
them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Stanley office at the address
indicated in this manual. Alternatively, a list of authorised
Stanley repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com
9
ENGLISH
(Original instructions)
EC declaration of conformity
Technical data
MACHINERY DIRECTIVE
STCD1081B2
Voltage
VDC
10.8
No-load speed
/min
0-315, 0-1200
Max. torque
(PTI Rating)
Nm
27
Chuck capacity
mm
10
mm
10/25
kg
1.1
Input Voltage
VAC
100 - 240
Output Voltage
VDC
10.8
Output Current (DC)
mA
400
Approx. charge time
h
3 - 4.5
Voltage
VDC
10.8
Capacity
Ah
1.5
STCD1081B2
STANLEY declares that these products described under
"technical data" are in compliance with:
2006/42/EC, EN 60745-1, EN 60745-2-1, EN60745-2-2
Max Drilling capacity
Steel/wood
Weight
These products also comply with Directive
“2004/108/EC (until 19.04.2016), 2014/30/EU (from
20.04.2016)” and 2011/65/EU. For more information, please
contact STANLEY at the following address or refer to the
back of the manual.
Charger
The undersigned is responsible for compilation of the
technical file and makes this declaration on behalf of
STANLEY.
Battery
Type
L pA (sound pressure)
Li-Ion
dB(A)
64,5
KpA (sound pressure uncertainty)
dB(A)
3
L WA (sound power)
dB(A)
75,5
KWA (sound power uncertainty)
dB(A)
3
Drilling into metal: ah,D =
m/s2
1,0
K =
m/s2
1,5
Screwdriving: ah =
m/s2
1,0
K=
m/s2
1,5
10
R.Laverick
Engineering Manager
STANLEY , Europe, Egide Walschaertsstraat14-18,
2800 Mechelen, Belgium
01.2015
(Original instructions)
ENGLISH
Service Information
STANLEY offers a full network of authorized service
locations. All STANLEY Service Centers are staffed with
trained personnel to provide customers with efficient and
reliable power tool service. For more information about our
authorized service centers and if you need technical advice,
repair, or genuine factory replacement parts, contact the
STANLEY location nearest you.
One years full warranty
If your STANLEY product becomes defective due to faulty
materials or workmanship within 12 months from the date of
purchase, STANLEY guarantees to replace all defective
parts free of charge or – at our discretion – replace the unit
free of charge provided that:
•
The product has not been misused and has been used in
accordance with the instruction manual.
•
The product has been subject to fair wear and tear;
•
Repairs have not been attempted by unauthorised
•
Proof of purchase is produced.
•
The STANLEY product is returned complete with all
If you wish to make a claim, contact your seller or check the
location of your nearest authorised STANLEY repair agent in
the STANLEY catalogue or contact your local STANLEY
office at the address indicated in this manual. A list of
authorised STANLEY repair agents and full details of our
after sales service is available on the internet
11
90623014
01/2015
Names & Addresses for STANLEY Service Concessionaries - MIDDLE EAST & AFRICA
ALGERIA: Sarl Outillage Corporation, 08 Rue Med Boudiaf - Cheraga - Algiers, Algeria. Tel: (213-21) 375130, Fax: (213-21) 369667. ANGOLA: Angoferraria,
Lda., Rua Robert Shields, No. 61, Luanda, Angola, Tel: 00244-222-395837 / 222-395034, Fax: 00244-222-394790. AZERBAIJAN: Royalton Holdings Ltd. 41
Khagani St. Apt. 47 AZ 1001, Baku. Tel: (994-12) 4935544, Fax: (994-12) 5980378. BAHRAIN: Kavalani & Sons W.L.L., P.O. Box 71, Sitra, Manama, Tel: (973)
17732888, Fax: (973) 17737379. Alfouz Services Co. WLL., P.O. Box 26562, Tubli, Manama. Tel: (973) 17783562, Fax: (973) 17783479. EGYPT: El Farab
S.A.E., 15-Nabil El Wakkad Street, Dokki, Giza, Egypt, Tel: 00202-37603946 / 002-010-2582544, Fax: 00202-33352796. ETHIOPIA: Seif Tewfik Sherif, Arada
Sub-City, Kebele 01/02, Global Insurance Building, 2nd Floor, Room 43, P.O. Box 2525, Addis Ababa, Ethiopia. Tel: (251-11) 1563968/ 1563969, Fax: (251-11)
1558009. IRAQ: Financial Links, Kazzaz Building Arasat Al-Hindia Block No: 629 Street: 31Building No: 1 Baghdad – Iraq. Tel: 00964 (0)780 195 2223/ 00964
(0)781 3763044. Al Sard Co. for General Trading Ltd. Jbara Bldg. 3Flr, Al Rasheed St. Bagdad. Tel: (964) 18184102. Sakhar Group, Arrassat al-hindya Al
Masbah, Bagdad. (964) 7400144446. JORDAN: Palestine Bldg. Matl. (Bashiti Hardware), 93 King Abdullah 2nd Street, Opp. ELBA House, P.O. Box 3005,
Amman 11953, Tel: (962-6) 5349098, Fax: (962-6) 5330731. KENYA: Dextron Tools Ltd., P.O. Box 20121-00200, Shariff House, Kimathi Street, Nairobi. Tel:
(254-20) 6905000/ 2358021, Fax: (254-20) 6905111/ 6905112. KUWAIT: Al Omar Technical Co., P.O. Box 4062, 13041 Safat, Kuwait. Tel: (965) 24848595/
24840039, Fax: (965) 24845652. Fawaz Al Zayani Establishment, P.O. Box 42426, Shop No. 18, Al Humaizi Commercial Complex, Khalifa Al Jassim,
Shuwaikh, Kuwait. Tel: (965) 24828710, Fax: (965) 24828716. Fawaz Al Zayani Establishment, P.O. Box 42426, Shop No.18, Al Humaizi Commercial
Complex, Khalifa Al Jassim, Shuwaikh, Kuwait, Tel: (965) 24828710, Fax: (965) 24828716. Fawaz Al Zayani Establishment, Fahaheel Industrial Area, Main St.,
Sanaya, Kuwait, Tel: (965) 23925830, Fax: (965) 24828716. LEBANON: Est. Shaya & Azar S.A.R.L., Boulvard Jdeideh - Mar Takla - Bouchrieh .P.O. Box
90545 Jdeideh.Beirut - Lebanon, Tel: 00961 1 872305 / 306 , Fax: 00961 1 872303. LIBYA: North Africa Trading ( El Ghoul Brothers), AlHilal Service Center
Tawergha St. Misurata, Tel: 00218-091-3221408. (Benghazi) Sniydel st., Amr Ibn EL-Aas Rd. Tel: (+218) 92 5771120. (Tripoli) Al Barniq Service Center,
Mokhazin elsukar st., ElFallah. Tel: (+218) 21 4808019. (Misrata) Al Hilal Service Center, Tawergha st. Tel: (+218) 51 2626743. MAURITIUS: Robert Le Marie
Limited, Old Moka Road, Bell Village, P.O. Box 161, Port Louis, Tel: 00230-212 1865/ 212 2847, Fax: 00230-2080843. MOROCCO: Ets Louis Guillaud & Cie,
149, Quartier Industriel, Moulay Rachid, Casablanca, Postal Code 20450, Morocco, Tel: 00212-522729233, Fax: 00212-522729096. NIGERIA: Meridian
Power Tools Ltd., Gr.Floor, #1 Alhaji Masha Rd, Next toTeslim Balogun Stadium, Near National Stadium Surulere, Lagos, Nigeria, Tel: 00234-1-7740431 /
7740410, Fax: 00234-1-7913798. OMAN: Al Jizzi Company LLC, P.O. Box 1704,PC 112 Ruwi, Oman, Tel: (968) 24832618/ 24835153, Fax: (968)
24831334/24836460. Al Hassan Technical & Construction Supplies Co. LLC, P.O. Box 1948, P.C. 112, Ruwi, Tel: (968) 24810575 / 24837054, Fax: (968)
24810287/ 24833080. Oman Hardware Co. LLC, P.O. Box 635, Ruwi Postal Code 112, Te: (968) 24815131, Fax: (968) 24816491. Khimji Ramdas, P.O. Box
19, Post Code 100, Ghala, Muscat, Oman. Tel: (968) 24595906/ 907, Fax: (968) 24852752. Oman Marketing & Service Co. (Omasco), P.O. Box 2734, Behind
Honda Showroom, Wattayah, Oman. Tel: (968) 24560232/ 24560255, Fax: (968) 24560993. Oman Marketing & Service Co. (Omasco), Al Ohi, Sohar, Oman.
Tel: (968) 26846379, Fax: (968) 26846379. Oman Marketing & Service Co. (Omasco), Sanaya, Salalah, Oman. Tel: (968) 23212290, Fax: (968) 23210936.
PAKISTAN: ZIT Co - Nasir & Bros., 2nd Floor, Qadri Center, Chowk Dalgran Railway Road, Lahore, Pakistan, Tel: 0092 42 37670839, Fax: 0092 42
37652989. Ammar Service & Spares, 60-Bank Arcade, Serai Road, Karachi, Pakistan. Tel: (92-21) 32426905, Fax: (92-21) 32427214. QATAR: Teyseer
Industrial Supplies & Services Co. WLL, 55, Al Wakalat St. (Between St. 18 & 19) Salwa Industrial Area, P.O. Box 40523 Doha,Qatar, Te: (974) 44581536, Fax:
(974) 44682024. Shaheen Electrical Works & Trading Co. WLL, Gate 34, St. 44 Industrial Area P.O. Box 9756, Doha, Tel: (974) 44600230 /44600525, Fax:
(974) 44601338. Al Muftah Service Centre, Al Wakrah Road, P.O. Box 875, Doha,Qatar, Tel: (974) 44650880/ 44650110/ 44446868, Fax: (974) 44441415 /
44662599. SAUDI ARABIA: (Al Bahr) Mohamed Ahmed Bin Afif Est., P.O. Box 530, Yanbu, Al Bahr. Tel: (966-4) 3222626/ 3228867, Fax: (966-4) 3222210.
(Al Khobar) Fawaz Ebrahim Al Zayani Trading Est., P.O. Box 76026, Al Khobar # 31952, Tel: (966-3) 8140914, Fax: (966-3) 8140824. MSS (Al-Mojil Supply &
Services) P.O. Box 450, Jubail 31951, Opp. Gulf Bridge Library & Riyadh House. Tel: (966-3) 3612850/ 3624487/ 3621729, Fax: (966-3) 3623589/ 3620783.
(Dammam) MSS (Al-Mojil Supply & Services), P.O. Box 450, Jubail 31951.Opp-Gulf Bridge Library & Riyadh House, Tel: (966-3) 3612850 / 3624487 /
3621729, Fax: (966-3) 3623589 / 3620783. Al Bawardi Tools & Hardware, P.O. Box 112, Dammam, Tel: (966-3) 8330780 Ext.24 / 8348585 Ext. 24 /
+966-3-8335555, Fax: (966-3) 8336303. (Al Hassa) Mutawa Trading & Gen. Services, Maliki road Hafuf city, Al Hassa, KSA. Tel: (966) 502846275 (Jeddah) Al
Bawardi Tools & Hardware, P.O. Box 16905, Jeddah 21474, Tel: (966-2) 6444547 / 6439035 / 6456095, Fax: (966-2) 6439024. EAC (Al Yousef Contg. & Trdg.
Est.), P.O. Box 30377, Jeddah -21477, Tel: (966-2) 6519912, Fax: (966-2) 6511153. (Madina) Garziz Trading for Bldg Mat & Decoration, P.O. Box 3364,
Madina, Tel: (966-4) 826 14 90 / 8227636, Fax: (966-4) 8265741. (Riyadh) Industrial Material Organization (IMO), P.O. Box 623, Rail Street ,Riyadh, Tel:
(966-1) 4028010 Ext 26 / 8001245757, Fax: (966-1) 4037970. Sultan Garment Factory (RSC), P.O. Box 29912, Riyadh 11467, KSA, Tel: (966-1) 4055148 /
4042889, Fax: (966-1) 4055148. Al Bawardi Tools & Hardware, P.O. Box 68, Riyadh 11411, Tel: (966-1) 4484999, Fax: (966-1) 4487877. (Yanbu) Fawaz
Ebrahim Al Zayani, Opposite to Al Fouzan, Jeddah highway or King Abdul Aziz road, Yanbu. Tel: (966-4) 3960980, Fax: (966-4) 3961980. Mohamed Ahmed
Bin Afif Est., P.O. Box 530, Yanbu, Al Bahr, Tel: (966-4) 3222626/ 3228867, Fax: (966-4) 3222210. SOUTH AFRICA: Stanley Black & Decker - RSA, 199
Winze Drive Stormill Ext 9 Roodepoort, Tel: (2711) 472 0454, Fax: (2711) 472 0482. Trevco Power Tool Service 14 Steenbok Street, Koedoespoort, 0186,
Pretoria, South Africa. Tel: (27-86) 1873826, Fax: (27-86) 5001771. TANZANIA: General Motors investment Ltd., P.O. Box 16541, 14 Nyerere Road,
Vingunguti, Dar-es-Salaam. Tel: (255 22) 2862661/ 2865022, Fax: (255 22) 2862667. TUNISIA: Societe Tunisienne De Maintenance (STM), Rue de la
Physique. Nouvelle Zone Industrielle Ben Arous., 2013 Ben Arous, Tunisia. Tel: (+216) 79 389687, Fax: (+216) 71 385154. UAE: (Abu Dhabi) Light House
Electrical, P.O. Box 120, Abu Dhabi, Tel: (971-2) 6726131, Fax: (971-2) 6720667. Galaxy Equipment Trading, Madinath Zayed (Baada Zaid), Abu Dhabi P.C.
58910, Tel: (971-2) 8844279, Fax: (971-2) 8844297 (Ajman) Al Sukoon Gen. Trdg. Co. LLC, P.O. Box 2975, Ajman. Tel: (971-6) 7435725/ 7438317, Fax:
(971-6) 7437350. Al Sukoon Gen. Trdg. Co. LLC, P.O. Box 2975, Ajman, Tel: (971-6) 7435725 / 7438317, Fax: (971-6) 7437350 (Al Ain) Zillion Equipment and
Spare Parts Trading LLC, P.O. Box 19740, Opp. Bin Sadal/ Trimix Redymix Sanaiya, Al Ain. Tel: (971-3) 7216690, Fax: (971-3) 7216103. (Dubai) Black &
Decker (Overseas) GmbH, P.O. Box 5420, Dubai, Tel: (971-4) 8127400/ 8127406, Fax: (971-4)2822765. Ideal Star Workshop Eqpt.Trading LLC, P.O. Box
37116, Al Quoz, Dubai, Tel: (971-4) 3474160, Fax: (971-4) 3474157, Fine Tools, P.O.Box 30139 , Al Quoz, Dubai, Tel: (971-4) 3385240, Fax: (971-4) 3385239,
Alebrah Engineering Service, P.O. Box 78954, Al Qusais , Dubai, Tel: (971-4) 2850044, Fax: (971-4) 2844802. (Musaffah) Light House Electrical, P.O. Box
120, Abu Dhabi, Tel: (971-2) 5548315, Fax: (971-2) 5540461. (Sharjah) Mc Coy Middle East LLC, P.O. Box 25793, Sharjah, Tel: (971-6) 5395931, Fax:
(971-6) 5395932. Burj Al Madeena, Industrial Area No.1, Opp. Pakistani Masjid, P.O. Box 37635, Sharjah. Tel: (971-6) 5337747, Fax: (971-6) 5337719. Burj Al
Madeena, , Industrial Area No 1,opp Pakistani Masjid P.O. Box 37635, Sharjah, Tel: (971-6) 5337747, Fax: (971-6) 5337719 (Ras Al Khaimah) Mc Coy Middle
East LLC, P.O. Box 10584, Ras Al Khaimah, Tel: (971-7) 2277095, Fax: (971-7) 2277096. UGANDA: The Building Center (U) Ltd., 52 Station Road, Kitgum
House, P.O. Box 7436, Kampala, Uganda. Tel: (256-41) 4234567/ 4259754, Fax: (256-41) 4236413. YEMEN: (Aden) Middle East Trad. Co. Ltd. (METCO),
Mualla Dakka, Aden, Yemen. Tel: (967-2) 222670, Fax: (967-2) 222670. (Sana'a) Middle East Trad. Co. Ltd. (METCO), Hayel St., Sana'a, Yemen. Tel: (967-1)
204201, Fax: (967-1) 204204. (Taiz) Middle East Trading Co. (METCO), P.O. Box 12363, 5th Flr, Hayel Saeed Anam Bldg, Al-Mugamma St. Taiz, Yemen. Tel:
(967-4) 213455, Fax: (967-4) 219869.
Download PDF

advertising