FME190 | Stanley FME190 MIXER instruction manual

11
8
7
7
2
2
8
3
6
3
6
4
5
4
5
9
www.stanley.eu
FME190
4
4
5
5
A
A
B
3
3
99
33
4
C
4
44
C
D
99
33
33
44
E
2
44
F
9
4
4
9
6
5 5
G
H
7
7
7
2.
7
1.
8
I
J
22
K
3
ENGLISH
(Original instructions)
Intended use
Your Stanley Fat Max FME190 Paddle Mixer has been
designed for mixing liquid and powdery materials: paints, glue/
adhesive, plaster, screed as well as mortar etc. This tool is
intended for professional and private, non professional users.
Safety instructions
General power tool safety warnings
@
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below
refers to your mains operated (corded) power tool or battery
operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply.
4
Use of an RCD reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
(Original instructions)
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. In
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5.Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Additional power tool safety warnings for paddle
mixer.
Never clamp the product into a vice or to a work bench to
use as a stationary tool. This may cause serious injury.
u Switch the product off immediately if the tool attachment
jams. Be prepared for high reaction torques, which could
cause kickbacks. The tool attachment will jam if the
product is overloaded or becomes twisted in the
workpiece.
u Wear protective clothing, dust masks and protective
gloves when using this product. While this product is
being used, dust may be created or splashing may occur
and material or liquids may be flung around. Many types
of dust are deemed to be carcinogenic.
u Always operate the product with both hands on the
handles. Keep a firm grip on the handles and ensure your
footing is secure on a stable, level and dry ground. Loss
of control over the product can cause personal injury.
u Do not use this product to process substance which is
highly flammable or potentially explosive such as solvents.
Using this product will create sparks which can ignite
vapours.
u Use this product indoors only. Moisture and rain can
damage the product or can lead to electrocution.
from the power supply, if stirred material penetrates into
the inside of the product or if the product falls into the
material being stirred. Have the product inspected by a
professional electrician. Stirred material and moisture
can damage the product or lead to electrocution, if they
penetrate inside the product.
u Do not work with any substances which are harmful
to health. Many materials are noxious when they are
processed.
u
ENGLISH
Do not breathe in any unhealthy substances and avoid
contact with your skin. Follow the manufacturers’
instructions and wear suitable personal protective
equipment.
u Wait until the product has come to a complete standstill,
before removing it from the material being stirred and
putting it down. The bucket can get jammed or stirred
material can be flung around. This can lead to a loss of
control over the product.
Residual risks.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving parts.
u Impairment of hearing.
u Risk of injury when changing any parts, or accessories.
u Health hazards caused by breathing dust developed when
sawing wood, especially oak, beech and MDF.
u Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
Safety of others
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
u Children should be supervised to ensure that they do not
play with the appliance.
u
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured
in accordance with a standard test method provided by
EN 60745 and may be used for comparing one tool with
another. The declared vibration emission value may also be
used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level
may increase above the level stated. When assessing
vibration exposure to determine safety measures required by
2002/44/EC to protect persons regularly using power tools
in employment, an estimation of vibration exposure should
consider, the actual conditions of use and the way the tool
is used, including taking account of all parts of the operating
cycle such as the times when the tool is switched off and
when it is running idle in addition to the trigger time.
5
ENGLISH
(Original instructions)
Labels on tool
The following pictograms along with the date code are shown
on the tool:
:
O
N
6
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Wear safety glasses or goggles.
Wear ear protection.
Wear a dust mask.
Wear gloves when handling blades.
Electrical safety
#
u
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
Inspect tool cords periodically. If the supply cord is
damaged, it must be replaced by the manufacturer or an
authorised Stanley Fat Max Service Centre in order to
avoid a hazard.
Voltage drops
Inrush currents cause short-time voltage drops. Under
unfavourable power supply conditions, other equipment may
be affected. If the system impedance of the power supply is
lower than 0.34 Ω, disturbances are unlikely to occur.
Using an extension cable
u Always use an approved extension cable suitable for the
power input of this tool (see technical data). Before use,
inspect the extension cable for signs of damage, wear and
ageing.
u Replace the extension cable if damaged or defective.
When using a cable reel, always unwind the cable
completely. Use of an extension cable not suitable for the
power input of the tool or which is damaged or defective
may result in a risk of fire and electric shock.
Features
This tool includes some or all of the following features.
1. Air vents
2. Handle (left & right)
3.Socket
4.Shaft
5.Stirrer
6
6. lock-on button
7. Variable speed switch
8. Power cord with plug
9. Mounting spanner 22mm (x 2)
Assembly.
Unpacking.
Unpack all parts and lay them on a flat, stable surface.
Remove all packing materials and shipping devices, if
applicable.
u Make sure the delivery contents are complete and free
of any damage. If you find that parts are missing or show
damage do not use the product but contact your dealer.
Using an incomplete or damaged product represents a
hazard to people and property.
u Ensure that you have all the accessories and tools needed
for assembly and operation. This also includes suitable
personal protective equipment.
Warning! The product and the packaging are not children’s
toys! Children must not play with plastic bags, sheets and
small parts! There is a danger of choking and suffocation!
u
u
Setup
Warning! The product must be fully assembled before
operation! Do not use a product that is only partly assembled
or assembled with damaged parts! Follow the assembly
instructions step-by-step and use the pictures provided as a
visual guide to easily assemble the product! Do not connect
the product to power supply before it is completely assembled!
Stirrer
Warning! Stirrers are available in different types and with
different shape and diameters. Always use the correct
stirrer according to the intended use! Observe the technical
requirements of this product (see section “Technical
specifications”) when purchasing and using stirrer! Stirrer
becomes hot during use! Handle them carefully! Wear
protective gloves when handling stirrer in order to avoid
injuries like burns and cuts!
Attaching (Fig.A, Fig.B, Fig.C, Fig.D)
Align the stirrer (5) with the shaft (4). Screw the stirrer (5)
clockwise onto the lower end of the shaft (4) (Fig. A).
u Lock the welded nut of the shaft (4) with one mounting
spanner (9) and secure the stirrer (5) clockwise with the
other (9) gripping the welded nut (Fig. B).
Note! Tighten the connection hand tight at first, before using
the spanners.
u Align the shaft (4) with the socket (3). Screw the shaft end
with welded nut clockwise into the socket (3) (Fig. C).
u Lock the socket (3) with one mounting spanner (9) and
secure the shaft (4) clockwise with another mounting
spanner (9) gripping the welded nut (Fig. D).
u
(Original instructions)
Note! Tighten the connection hand tight at first, before using
the spanners.
Removing/Replacing (Fig.E, Fig.F)
Lock the socket (3) with one mounting spanner (9) and
loosen the shaft (4) anticlockwise with another mounting
spanner (9) gripping the welded nut (Fig. E).
u Loosen the welded nut anticlockwise (Fig. F) and remove
the shaft (4) from the socket (3) (Fig. F)
u
Stirrer (Fig.G, Fig.H)
Lock the welded nut of the shaft (4) with one mounting
spanner (9) and loosen the stirrer (5) anticlockwise with
another mounting spanner (9) gripping the welded nut
(Fig. G).
u Loosen the welded nut anticlockwise (Fig. H) and remove
the stirrer (5) from the shaft (4) (Fig. H).
u Attach a new shaft/stirrer as required.
u
Use
Variable speed switch (Fig.I)
Operate the product either in instant or continuous mode.
Instant Mode
Switch the product on by pressing the variable speed
switch (7) (Fig. I).
u Switch the product off by releasing the variable speed
switch (7).
u
Continuous mode
Switch the product on by pressing the variable speed
switch (7) and hold it in position (Fig. J, step 1).
u Press the lock-on button (6) and hold it in position to lock
the variable speed switch (7) (Fig. I, step 2).
u Release the lock-on button (6) and variable speed switch
(8). The variable speed switch is now locked on for
continuous use.
u Depress and release the variable speed switch (7) to
switch the product off.
u
General operation
Check the product, its power cord and plug as well as
accessories for damage before each use. Do not use the
product if it is damaged or shows wear.
u Double check that the accessories and attachments are
properly fixed.
u Always hold the product on its handles. Keep the handles
dry to ensure safe support.
u Ensure that the air vents are always unobstructed and
clear. Clean them if necessary with a soft brush. Blocked
air vents may lead to overheating and damage the
product.
u
ENGLISH
Switch the product off immediately if you are disturbed
while working by other people entering the working area.
Always let the product come to complete stop before
putting it down.
u Do not overwork yourself. Take regular breaks to ensure
you can concentrate on the work and have full control over
the product.
u
Mixing (Fig.K)
Warning! During operation fine dust will be generated!
Some dusts are highly inflammable and explosive! Do not
smoke during operation, keep heat sources and open flames
out of the working area! Always wear a dust mask to protect
yourself against hazards resulting from fine dust!
The stirrer will come to a stop during operation if the material
is too firm! Switch the product off, lift the stirrer out of the
material and inspect the material before using the product
again! A blocked stirrer may cause overheating the of the
motor. Hold the product firmly during operation. Do not let the
stirrer touch the bucket! This can cause damage to the stirrer
and bucket!
u Hold the product with 2 hands on both handles (2) and
insert the stirrer (5) into the material (Fig. M).
u Gently press variable speed trigger switch to start
operation at a low speed.
u Move the stirrer through the material until it is evenly and
completely mixed.
u Switch the product off. Let the stirrer come to a complete
stop before lifting it out of the mixing material.
Warning: Switch the product off, let it come to a complete
stop and disconnect it from the power supply if the stirrer
gets stuck in the mixing material. Only then free the jammed
attachment.
After use
Warning: Always switch the product off, disconnect the
product from the power supply and let the product cool down
before performing inspection, maintenance and cleaning work!
Cleaning
Keep the product clean. Remove debris from it after each
use and before storage.
u Regular and proper cleaning will help ensure safe use and
prolong the life of the product.
u Inspect the product before each use for worn and
damaged parts. Do not operate it if you find broken and
worn parts.
Warning: Only perform repairs and maintenance work
according to these instructions! All further works must be
performed by a qualified specialist!
u Clean the product with a dry cloth. Use a brush for areas
that are hard to reach.
u
7
ENGLISH
(Original instructions)
In particular clean the air vents (1) after every use with a
cloth and brush.
u Remove stubborn dirt with high pressure air (max. 3 bar).
Note: Do not use chemical, alkaline, abrasive or other
aggressive detergents or disinfectants to clean this product as
they might be harmful to its surfaces.
u Check for worn or damaged parts. Replace worn parts
as necessary or contact an authorised service centre for
repair before using the product again.
u
Troubleshooting
Suspected malfunctions are often due to causes that the
users can fix themselves. Therefore check the product using
this section. In most cases the problem can be solved quickly.
Problem
Possible Cause
Solution
Product does not start
Not connected to power
supply
Connect to power
supply
Power cord or plug is
defective
Check by a specialist
electrician
Other electrical defect to
the product
Check by a specialist
electrician
Extension cord not suitable
for operation with this
product
Use a proper
extension cord
Power source (e.g.
generator) has too low
voltage
Connect to another
power source
Air vents are blocked
Clean the air vents
Stirrer is worn
Replace with new
one
Stirrer not suitable for
material to be mixed
Use proper stirrer
Maintenance
u
Before and after each use, check the product and
accessories (or attachments) for wear and damage. If
required, exchange them for new ones as described in this
instruction manual. Observe the technical requirements.
Product does not
reach full power
Repair
This product does not contain any parts that can be repaired
by the consumer. Contact an authorised service centre or a
similarly qualified person to have it checked and repaired.
Storage
Switch the product off and disconnect it from the power
supply.
u Clean the product as described above.
u Store the product and its accessories in a dark, dry, frostfree, well-ventilated place.
u Always store the product in a place that is inaccessible to
children. The ideal storage temperature is between 10°C
and 30°C.
u We recommend using the original package for storage or
covering the product with a suitable cloth or enclosure to
protect it against dust.
u
Transportation
Switch the product off and disconnect it from the power
supply.
u Attach transportation guards, if applicable.
u Always carry the product by its handles (2).
u Protect the product from any heavy impact or strong
vibrations which may occur during transportation in
vehicles.
u Secure the product to prevent it from slipping or falling
over.
u
8
Unsatisfactory
result
ENGLISH
(Original instructions)
Protecting the environment
Z
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Stanley Fat Max product
needs replacement, or if it is of no further use to you, do
not dispose of it with household waste. Make this product
available for separate collection.
z
Separate collection of used products and packaging allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Stanley Europe provides a facility for the collection and
recycling of Stanley Fat Max products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
Technical data
FME190
Rated voltage, frequency
220 – 240 V~, 50 Hz
Rated power input
1600 W
Rated no load speed n0
180 - 460rpm 300-750rpm
Diameter of stirrer
Ø 140mm
Coupling thread
M14 x 2
Mixture volume
max. 120L
Max torque
80 Nm
Protection class
Class ll
Weight
approx. 5.1 kg
Sound pressure level LpA
84 dB (A)
Sound power level LWA
95 dB (A)
Uncertainty KpA, KWA
3 dB (A)
>ah
4.24 m/s2
You can check the location of your nearest authorised repair
agent by contacting your local Stanley Europe office at
the address indicated in this manual. Alternatively, a list of
authorised Stanley Europe repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
9
ENGLISH
(Original instructions)
EC declaration of conformity
MACHINERY DIRECTIVE
%
FME190 Paddle mixer
Stanley Europe declares that these products described under
"technical data" are in compliance with:
2006/42/EC, EN 60745-1:2009 + A11:2010,
EN 60745-2-11: 2010
These products also comply with Directive 2004/108/EC (until
19/04/2016) 2014/30/EU (from 20/04/2016) and
2011/65/EU. For more information, please contact Stanley
Europe at the following address or refer to the back of the
manual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of Stanley Europe.
Ray Laverick
Engineering Manager
Stanley Europe, Egide Walschaertsstraat14-18,
2800 Mechelen, Belgium
01/26/2015
10
Guarantee
Stanley Europe is confident of the quality of its products
and offers an outstanding guarantee for professional users
of the product. This guarantee statement is in addition to
and in no way prejudices your contractual rights as a private
non-professional user. The guarantee is valid within the
territories of the Member States of the European Union and
the European Free Trade Area.
ONE-YEAR FULL WARRANTY
If your Stanley Fat Max product becomes defective due to
faulty materials or workmanship within 12 months from the
date of purchase, Stanley Europe guarantees to replace all
defective parts free of charge or – at our discretion – replace
the unit free of charge provided that:
u The product has not been misused and has been used in
accordance with the instruction manual.
u The product has been subject to fair wear and tear;
u Repairs have not been attempted by unauthorised
persons;
u Proof of purchase is produced.
u The Stanley Fat Max product is returned complete with all
original components
If you wish to make a claim, contact your seller or check the
location of your nearest authorised Stanley Fat Max repair
agent in the Stanley Fat Max catalogue or contact your local
Stanley office at the address indicated in this manual. A list
of authorised Stanley Fat Max repair agents and full details of
our after sales service is available on the internet at:
www.stanley.eu/3
(Original instructions)
ENGLISH
11
United Kingdom
Stanley Fat Max
210 Bath Road
Slough, Berkshire SL1 3YD
90625538 REV-0
Tel. 01753 511234
Fax 01753 572112
www.stanleytools.co.uk
05/2015
Download PDF