SCD12S2 | Stanley SCD12S2 CORDLESS DRILL instruction manual

SCD12
English
French
Russian
Turkish
Portugese
Arabic
4-14
15-25
16-26
27-37
38-48
49-59
FIG. A
5
4
3
2
8
9
1
6
7
FIG. B
7
10
FIG. D
FIG. C
3
4
6
7
FIG. E
FIG. F
FIG. G
FIG. H
ENGLISH
Intended use
Your Stanley SCD12 10.8V Li-Ion Drill Driver has been designed for light fastening and drilling applications. This tool
is intended for semi-professional and professional use.
Safety instructions
General power tool safety warnings
WARNING! Read all safety warnings and instructions. Failure to follow the warnings and instructions may result
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless)
power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of
Power tools
create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet.
Never modify the plug in any way. Do not
use any adapter plugs with earthed
(grounded) power tools.
matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or
grounded surfaces such as pipes, radiators,
ranges and refrigerators. There is an increased
risk of electric shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet
conditions. Water entering a power tool will increase
the risk of electric shock.
d. Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
e. When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of
electric shock.
4
f. If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and
use common sense when operating a power
tool. Do not use a power tool while you are
or medication. A moment of inattention while
operating power tools may result in serious personal
injury.
b. Use personal protective equipment. Always
wear eye protection. Protective equipment such as
dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
c. Prevent unintentional starting. Ensure the
switch is in the off-position before
connecting to power source and/or battery
pack, picking up or carrying the tool. Carrying
power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in
personal injury.
e. Do not overreach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving parts.
g. If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce dust-related
hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the rate for
which it was designed.
b. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
ENGLISH
c. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the
power tool accidentally.
d. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are dangerous
in the hands of untrained users.
e. Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tools operation. If
damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool
bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to be
performed. Use of the power tool for operations
different from those intended could result in a hazardous
situation.
5. Battery tool use and care
a.
the manufacturer. A charger A charger that is
suitable for one type of battery pack may create a risk of
b.
designated battery packs. Use of any other
c. When battery pack is not in use, keep it
away from other metal objects like paper
clips, coins, keys, nails, screws or other
small metal objects that can make a
connection from one terminal to another.
Shorting the battery terminals together may cause burns
d. Under abusive conditions, liquid may be
ejected from the battery, avoid contact. If
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the battery
may cause irritation or burns.
6. Service
a.
repair person using only identical
replacement parts. This will ensure that the safety of
the power tool is maintained.
Additional safety warnings for drills
and impact drills
• Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
• Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
• Hold power tool by insulated gripping
surfaces when performing an operation
where the cutting accessory may contact
hidden wiring. Cutting accessory contacting a “live”
wire may make exposed metal parts of the power tool “live”
and could give the operator an electric shock.
• Never use a chisel accessory in rotary mode.
The accessory will bind in the material and rotate the drill.
• Use clamps or another practical way to secure and support
the workpiece to a stable platform. Holding the work by
hand or against your body leaves it unstable and may lead
to loss of control.
• Before drilling into walls, floors or ceilings, check for the
location of wiring and pipes.
• Avoid touching the tip of a drill bit just after drilling, as it
may be hot.
• The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recommended in this instruction manual may present a risk of
personal injury and/or damage to property.
Safety of others
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
• Children should be supervised to ensure that they do not
play with the appliance.
Residual Risks
In spite of the application of the relevant safety regulations and
the implementation of safety devices, certain residual risks
cannot be avoided.
These are:
• Impairment of hearing.
• Risk of personal injury due to flying particles.
• Risk of burns due to accessories becoming hot during
operation.
• Risk of personal injury due to prolonged use.
5
ENGLISH
LABELS ON TOOL
The label on your tool may include the following pictographs
along with the date code:
WARNING! To reduce the risk of injury, the user must read
the instruction manual.
Read instruction manual before use.
Always wear safety goggles.
Always wear safety hearing protection.
POSITION OF DATE CODE
The Date Code, which also includes the year of manufacture, is
printed into the housing.
Example:
2015 XX JN
Year of manufacturing
Important Safety Instructions for All
Battery Chargers
SAVE THESE INSTRUCTIONS: This manual contains
important safety and operating instructions for SC121 battery
chargers.
• Before using charger, read all instructions and cautionary
markings on charger, battery pack, and product using
battery pack.
WARNING: Shock hazard. Do not allow any
liquid to get inside charger. Electric shock may
result.
CAUTION: Burn hazard. To reduce the risk
of injury, charge only STANLEY rechargeable
batteries. Other types of batteries may burst
causing personal injury and damage.
CAUTION: Children should be supervised to
ensure that they do not play with the appliance.
NOTICE: Under certain conditions, with the
charger plugged in to the power supply, the
charger can be shorted by foreign material.
Foreign materials of a conductive nature such as,
but not limited to, grinding dust, metal chips, steel
wool, aluminum foil, or any buildup of metallic
particles should be kept away from charger
cavities. Always unplug the charger from the
power supply when there is no battery pack in the
cavity. Unplug charger before attempting to clean.
• DO NOT attempt to charge the battery pack
with any chargers other than the ones in
this manual. The charger and battery pack are
specifically designed to work together.
• These chargers are not intended for
any uses other than charging STANLEY
rechargeable batteries. Any other uses may result
in risk of fire, electric shock or electrocution.
6
• Do not expose charger to rain or snow.
• Pull by plug rather than cord when
disconnecting charger. This will reduce risk of
damage to electric plug and cord.
• Make sure that cord is located so that it
will not be stepped on, tripped over, or
otherwise subjected to damage or stress.
• Do not use an extension cord unless it is
absolutely necessary. Use of improper extension
cord could result in risk of fire, electric shock, or
electrocution.
• Do not place any object on top of charger
or place the charger on a soft surface that
might block the ventilation slots and result
in excessive internal heat. Place the charger in
a position away from any heat source. The charger is
ventilated through slots in the top and the bottom of the
housing.
• Do not operate charger with damaged cord
or plug — have them replaced immediately.
• Do not operate charger if it has received
a sharp blow, been dropped, or otherwise
damaged in any way. Take it to an authorised
service centre.
• Do not disassemble charger; take it to an
authorised service centre when service or
repair is required. Incorrect reassembly may result in
a risk of electric shock, electrocution or fire.
• In case of damaged power supply cord the supply cord
must be replaced immediately by the manufacturer, its
service agent or similar qualified person to prevent any
hazard.
• Disconnect the charger from the outlet
before attempting any cleaning. This will
reduce the risk of electric shock. Removing the
battery pack will not reduce this risk.
• NEVER attempt to connect 2 chargers together.
• The charger is designed to operate on
standard household electrical power. Do not
attempt to use it on any other voltage. This
does not apply to the vehicular charger.
Save these instructions
Chargers
The SC121 chargers accept 10.8V Li-Ion batteries.
These chargers require no adjustment and are designed to be
as easy as possible to operate.
Charging Procedure (Fig. B)
ENGLISH
• Plug the charger (10) into an appropriate outlet before
inserting battery pack.
• Insert the battery pack (7) into the charger. The red
(charging) light will blink continuously indicating that the
charging process has started.
• The completion of charge will be indicated by the red light
remaining ON continuously. The pack is fully charged and
may be used at this time or left in the charger.
NOTE: To ensure maximum performance and life of Li-Ion
batteries, charge the battery pack fully before first use.
Charging Process
Refer the tables below for the state of charge of the battery
pack.
State of charge
charging
––
fully charged
––––––––––––––––––––
hot/cold pack delay ––
––
––
–– ––
––
––
–––––––
HOT/COLD PACK DELAY
When the charger detects a battery that is hot, it automatically
delays charging until the battery has cooled.
When the charger detects a battery that is cold, it automatically
delays charging until the battery has warmed.
The red light will continue to blink, but a yellow indicator light
will be illuminated during this operation. Once the battery has
cooled, the yellow light will turn off and the charger will resume
the charging procedure.
Electronic protection system
Li-Ion batteries are designed with an Electronic Protection
System that will protect the battery against overloading,
overheating or deep discharge.
The tool will automatically turn off if the Electronic Protection
System engages. If this occurs, place the Li-Ion battery on the
charger until it is fully charged.
Read all instructions
• Do not charge or use battery in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Inserting or
removing the battery from the charger may ignite the dust
or fumes.
• Never force battery pack into charger. Do
not modify battery pack in any way to fit
into a non-compatible charger as battery
pack may rupture causing serious personal
injury.
• Charge the battery packs only in STANLEY chargers.
• DO NOT splash or immerse in water or other liquids.
• Do not store or use the tool and battery
pack in locations where the temperature
may reach or exceed 40 ˚C (105 ˚F) (such
as outside sheds or metal buildings in
summer).
WARNING: Never attempt to open the battery
pack for any reason. If battery pack case is
cracked or damaged, do not insert into charger.
Do not crush, drop or damage battery pack.
Do not use a battery pack or charger that has
received a sharp blow, been dropped, run over
or damaged in any way (i.e., pierced with a nail,
hit with a hammer, stepped on). Electric shock or
electrocution may result. Damaged battery packs
should be returned to service centre for recycling.
CAUTION: When not in use, place
tool on its side on a stable surface
where it will not cause a tripping or
falling hazard. Some tools with large battery
packs will stand upright on the battery pack but
may be easily knocked over.
Specific safety instructions for lithium ion
(Li-Ion)
Important Safety Instructions for All
Battery Packs
• Do not incinerate the battery pack even if it
is severely damaged or is completely worn
out. The battery pack can explode in a fire. Toxic fumes
and materials are created when lithium ion battery packs
are burned.
The battery pack is not fully charged out of the carton. Before
using the battery pack and charger, read the safety instructions
below. Then follow charging procedures outlined.
• If battery contents come into contact with
the skin, immediately wash area with mild
soap and water. If battery liquid gets into the eye,
rinse water over the open eye for
15 minutes or until irritation ceases. If medical attention is
needed, the battery electrolyte is composed of a mixture of
When ordering replacement battery packs, be sure to include
catalog number and voltage.
7
ENGLISH
battery performance and life, store battery packs at room
temperature when not in use.
liquid organic carbonates and lithium salts.
• Contents of opened battery cells may cause
respiratory irritation. Provide fresh air. If symptoms
persists, seek medical attention.
WARNING: Burn hazard. Battery liquid may be
flammable if exposed to spark or flame.
Transportation
STANLEY batteries comply with all applicable shipping
regulations as prescribed by industry and legal standards which
include UN Recommendations on the Transport of Dangerous
Goods; International Air Transport Association (IATA) Dangerous
Goods Regulations, International Maritime Dangerous Goods
(IMDG) Regulations, and the European Agreement Concerning
The International Carriage of Dangerous Goods by Road (ADR).
Lithium-ion cells and batteries have been tested to section 38.3
of the UN Recommendations on the Transport of Dangerous
Goods Manual of Tests and Criteria.
In most instances, shipping a STANLEY battery pack will be
excepted from being classified as a fully regulated Class 9
Hazardous material. In general, the two instances that require
shipping Class 9 are:
1. Air shipping more than two STANLEY lithium-ion battery
packs when the package contains only battery packs (no
tools), and
2. For long storage, it is recommended to store a fully
charged battery pack in a cool, dry place out of the charger
for optimal results.
NOTE: Battery packs should not be stored completely
depleted of charge. The battery pack will need to be recharged
before use.
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual, the labels
on the charger and the battery pack may show the following
pictographs:
Read instruction manual before use.
See Technical Data for charging time.
100%
Battery charging.
100%
Battery charged.
2. Any shipment containing a lithium-ion battery with an
energy rating greater than 100 watt hours (Wh). All lithiumion batteries have the watt hour rating marked on the pack.
Battery defective.
Regardless of whether a shipment is considered excepted
or fully regulated, it is the shipper's responsibility to consult
the latest regulations for packaging, labeling/marking and
documentation requirements.
Hot/cold pack delay.
Transporting batteries can possibly cause fire if the battery
terminals inadvertently come in contact with conductive
materials. When transporting batteries, make sure that the
battery terminals are protected and well insulated from materials
that could contact them and cause a short circuit.
Do not charge damaged battery packs.
Do not probe with conductive objects.
Do not expose to water.
The information provided in this section of the manual is
provided in good faith and believed to be accurate at the time
the document was created. However, no warranty, expressed or
implied, is given. It is the buyer’s responsibility to ensure that its
activities comply with the applicable regulations.
Have defective cords replaced immediately.
Charge only between 4 ˚C and 40 ˚C.
Only for indoor use.
Battery Pack
BATTERY TYPE
Discard the battery pack with due care for the
environment.
The SCD12 operates on a 10.8V 1.5Ah Li-Ion battery pack.
Refer to Technical Data for more information.
Storage Recommendations
1. The best storage place is one that is cool and dry away
from direct sunlight and excess heat or cold. For optimum
8
SC121
Charge STANLEY battery packs only with
designated STANLEY chargers. Charging battery
packs other than the designated STANLEY
batteries with a STANLEY charger may make them
burst or lead to other dangerous situations.
ENGLISH
Do not incinerate the battery pack.
Package Contents
The package contains:
1 Drill/driver
1 Charger
2 Batteries (S2) or 1 Battery (S1)
1 Instruction manual
NOTE: Battery packs and chargers are not included with
N-models.
•Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this
manual prior to operation.
Description (Fig. A)
WARNING: Never modify the power tool or
any part of it. Damage or personal injury could
result.
1. Trigger switch
2. Forward/reverse button
3. Torque adjustment collar
4 Gear shifter
5. Keyless chuck
6. Battery release button
7. Battery pack
8. LED Worklight
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the battery pack voltage corresponds to the
voltage on the rating plate. Also make sure that the voltage of
your charger corresponds to that of your mains.
Your STANLEY charger is double insulated in
accordance with EN 60335; therefore no earth
wire is required.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the STANLEY
service organisation.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for the
power input of your charger (see Technical Data). The
minimum conductor size is 1 mm2; the maximum length is 30 m.
When using a cable reel, always unwind the cable completely.
Assembly and adjustments
WARNING: Prior to assembly and adjustment,
always remove the battery pack. Always switch
off the tool before inserting or removing the
battery pack.
WARNING: Use only STANLEY battery packs
and chargers.
Inserting and Removing the
Battery Pack from the Tool (Fig. C)
WARNING: To reduce the risk
of serious personal injury, place
the forward/reverse button in
the lock-off position or turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up can
cause injury.
NOTE: Make sure your battery pack (7) is fully charged.
To install the battery pack into the tool handle
1. Align the battery pack with the rails inside the handle.
2. Slide it firmly into place until you hear the lock snap into
place.
To remove the battery pack from the tool
1. Press the release button (6) and firmly pull the battery pack
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Operating Instructions
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, place
the forward/reverse button in
the lock-off position or turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories.
Proper Hand Position (Fig. A, H)
WARNING: To reduce the risk of serious
personal injury, ALWAYS use proper hand
position as shown.
9
ENGLISH
WARNING: To reduce the risk of serious
personal injury, ALWAYS hold securely in
anticipation of a sudden reaction.
Proper hand position requires one hand on the main handle (i).
Trigger Switch (Fig. A)
To turn the tool on, squeeze the trigger switch (1). To turn the
tool off, release the trigger switch. Your tool is equipped with
a brake. The chuck will stop when the trigger switch is fully
released.
The variable speed switch enables you to select the best speed
for a particular application. The further you squeeze the trigger,
the faster the tool will operate. For maximum tool life, use
variable speed only for starting holes or fasteners
NOTE: Continuous use in variable speed range is not
recommended. It may damage the switch and should be
avoided.
Forward/Reverse Control Button
(Fig. A)
A forward/reverse control button (2) determines the direction of
the tool and also serves as a lock-off button.
To select forward rotation, release the trigger switch and depress
the forward/reverse control button on the right side of the tool.
To select reverse, depress the forward/reverse control button on
the left side of the tool. The center position of the control button
locks the tool in the off position. When changing the position of
the control button, be sure the trigger is released.
NOTE: The first time the tool is run after changing the direction
of rotation, you may hear a click on start up. This is normal and
does not indicate a problem.
LED Worklight (Fig. A)
There is a LED worklight (8) located under the torque
adjustment collar (3). The worklight will be activated when the
trigger switch is squeezed.
NOTE: The worklight is for lighting the immediate work surface
and is not intended to be used as a flashlight.
Torque Adjustment Collar (Fig. A)
The torque adjustment collar (3) is clearly marked with numbers
and a drill bit symbol.The collar should be rotated until the desired
setting is located at the top of the tool. Locators are provided in the
collar to eliminate the guess work when selecting fastening torque.
The higher the number on the collar, the higher the torque and
the larger the fastener which can be driven. To lock the clutch for
drilling operations, move to the drill bit position.
NOTE: When using the drill/driver for drilling holes, be sure that
the torque adjusting collar is set so the figure of the drill is aligned
with the center line on the top ofthe tool. Failure to do this will
allow the clutch to slip while attempting to drill.
10
Gear Shifter (Fig. A, D)
The dual range feature of your driver/drill allows you to shift gears
for greater versatility.
To select the low speed, high torque setting, turn the tool off and
permit to stop. Slide the gear shifter (4) forward (towards the
chuck). To select the high speed, low torque setting, turn the tool
off and permit to stop. Slide the gear shifter back (away from
chuck).
NOTE: Do not change gears when the tool is running. If you
are having trouble changing gears, make sure that the dual range
gear shifter is either completely pushed forward or completely
pushed back.
Keyless Chuck (Fig. E)
Your tool features a keyless chuck with one rotating sleeve for
one-handed operation of the chuck. To insert a drill bit or other
accessory, follow these steps.
1. Lock the trigger in the OFF position as previously described.
2. Grasp the black sleeve of the chuck with one hand and
use the other hand to secure the tool. Rotate the sleeve
counterclockwise far enough to accept the desired
accessory.
3. Insert the accessory about 19 mm (3/4") into the chuck and
tighten securely by rotating the chuck sleeve clockwise with
one hand while holding the tool with the other. Your tool is
equipped with an automatic spindle lock mechanism. This
allows you to open and close the chuck with one hand.
To release the accessory, repeat step 2 above.
WARNING: Do not attempt to tighten drill bits
(or any other accessory) by gripping the front part
of the chuck and turning the tool on. Damage to the
chuck and personal injury may result. Always lock
off trigger switch when changing accessories.
Be sure to tighten chuck with one hand on the chuck sleeve and
one hand holding the tool for maximum tightness.
Chuck removal (FIG. F)
Turn the adjustment collar to the “drill” position and gear shifter
to position 1 (low speed). Tighten the chuck around the shorter
end of a hex key (not supplied) of 6.35 mm (1/4") or greater
size. Using a wooden mallet or similar object, strike the longer
end in the clockwise direction, as shown. This will loosen the
screw inside the chuck.
Open chuck jaws fully, insert screwdriver (or Torx tool if required)
into front of chuck between jaws to engage screw head.
Remove screw by turning clockwise (left-hand-thread). Place
hex key in chuck and tighten, as shown in Figure F. Using
a wooden mallet or similar object, strike key sharply in the
counterclockwise direction. This will loosen the chuck so that it
can be unscrewed by hand.
ENGLISH
Chuck installation (FIG. G)
Screw the chuck on by hand as far as it will go and insert screw
(left-hand thread). Tighten screw securely. Tighten the chuck
around the shorter end of a 6.35 mm (1/4") or larger hex key
(not supplied) strike the longer end in the clockwise direction
with a wooden mallet, as shown. Tighten the screw once again
by turning in a counterclockwise direction.
Drill Operation
WARNING: To reduce the risk of serious
personal injury, turn tool off and disconnect
tool from power source before making any
adjustments or removing/installing attachments or
accessories.
WARNING: To reduce the risk of
personal injury, ALWAYS ensure
workpiece is anchored or clamped firmly. If drilling
thin material, use a wood “back-up” block to
prevent damage to the material.
Turn the collar to the drill bit symbol for drilling. Select the desired
speed/torque range using the gear shifter to match the speed and
torque to the planned operation.
• Use sharp drill bits only. For WOOD, use twist drill bits,
spade bits, or hole saws. For METAL, use high-speed steel
(HHS) twist drill bits or hole saws.
• Always apply pressure in a straight line with the bit. Use
enough pressure to keep drill biting, but do not push hard
enough to stall the motor or deflect the bit.
• Hold tool firmly with both hands to control the twisting
action of the drill.
WARNING: The drill may stall if overloaded
causing a sudden twist. Always expect the stall.
Grip the drill firmly with both hands to control the
twisting action and avoid injury.
• IF DRILL STALLS, it is usually because it is
being overloaded or improperly used. RELEASE
TRIGGER IMMEDIATELY, remove drill bit from
work, and determine cause of stalling. DO NOT CLICK
TRIGGER ON AND OFF IN AN ATTEMPT
TO START A STALLED DRILL — THIS CAN
DAMAGE THE DRILL.
• To minimize stalling or breaking through the material,
reduce pressure on drill and ease the bit through the last
fractional part of the hole.
• Keep the motor running when pulling the bit back out of a
drilled hole. This will help prevent jamming.
• With variable speed drills there is no need to center punch
the point to be drilled. Use a slow speed to start the hole
and accelerate by squeezing the trigger harder when the
hole is deep enough to drill without the bit skipping out.
Operation as a Screwdriver
Select the desired speed/torque range using the dual range
gear shifter on the top of tool to match the speed and torque to
the planned operation.
Insert the desired fastener accessory into the chuck as you
would any drill bit. Make a few practice runs in scrap or unseen
areas to determine the proper position of the clutch collar.
MAXIMUM RECOMMENDED CAPACITIES
Bits, Metal
Drilling
Wood, Flat
Boring
Hole Saws
Low Range–1
High Range–2
6.00 mm
3.00 mm
19.00 mm
12.00 mm
19.00 mm
16.00 mm
Maintenance
Your STANLEY power tool has been designed to operate over a
long period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and regular
cleaning.
WARNING: To reduce the risk
of serious personal injury, place
the forward/reverse button in
the lock-off position or turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up can
cause injury.
The charger and battery pack are not serviceable. There are no
serviceable parts inside.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of the
main housing with dry air as often as dirt is seen
collecting in and around the air vents. Wear
approved eye protection and approved dust mask
when performing this procedure.
11
ENGLISH
WARNING: Never use solvents or other
harsh chemicals for cleaning the non-metallic
parts of the tool. These chemicals may weaken
the materials used in these parts. Use a cloth
dampened only with water and mild soap. Never
let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the
charger from the AC outlet before cleaning. Dirt
and grease may be removed from the exterior
of the charger using a cloth or soft non-metallic
brush. Do not use water or any cleaning
solutions.
Optional Accessories
WARNING: Since accessories, other than
those offered by STANLEY, have not been tested
with this product, use of such accessories with
this tool could be hazardous. To reduce the risk of
injury, only STANLEY, recommended accessories
should be used with this product.
Consult your dealer for further information on the appropriate
accessories.
Protecting the Environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you nd one day that your STANLEY product needs
replacement, or if it is of no further use to you, do not dispose
of it with household waste. Make this product available for
separate collection.
Separate collection of used products and
packaging allows materials to be recycled and
used again. Re-use of recycled materials helps
prevent environmental pollution and reduces
the demand for raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste sites
or by the retailer when you purchase a new product.
12
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails to
produce sufficient power on jobs which were easily done before.
At the end of its technical life, discard it with due care for our
environment:
• Run the battery pack down completely, then remove it from
the tool.
• Li-Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.
Remarks
Stanley's policy is one of continuous improvement to our
products and as such, we reserve the right to modify product
specifications without prior notice.
• Standard equipment and accessories may vary by country.
• Product specifications may differ by country.
• Complete product range may not be available in all
countries. Contact your local Stanley dealers for range
availability.
ENGLISH
Technical data
SPECIFICATION
Voltage
No-load speed:
1st gear
2nd gear
Max torque
Power output (MWO)
Chuck capacity
Maximum drilling capacity:
Wood
Meta
CHARGER
Input Voltage
Output Voltage
Output Current(DC)
Approx. charge time
Battery
Voltage
Capacity
Type
SCD12
VDC
10.8
min-1
min-1
Nm
W
mm
0–400
0–1500
26
180
10
mm
mm
20
10
SC121
220-240
22
1.25
70(1.5Ah)
SB12S
10.8
1.5
Li-Ion
VAC
VDC
A
min
VDC
Ah
LEVEL OF SOUND PRESSURE ACCORDING TO EN
60745:
VIBRATION
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured
in accordance with a standard test method provided by EN
60745 and may be used for comparing one tool with another.
The declared vibration emission value may also be used in a
preliminary assessment of exposure.
WARNING! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
SERVICE INFORMATION
STANLEY offers a full network of company-owned and
authorized service locations. All STANLEY Service Centers
are staffed with trained personnel to provide customers with
efficient and reliable power tool service. For more information
about our authorized service centers and if you need technical
advice, repair, or genuine factory replacement parts, contact the
STANLEY location nearest you.
Sound pressure (LpA) 65.0 dB(A), uncertainty (K) 3 dB(A)
TWO YEARS WARRANTY
Sound power (LWA) 76.0 dB(A), uncertainty (K) 3 dB(A)
If your STANLEY product becomes defective due to faulty
materials or workmanship within 24 months from the date of
purchase, STANLEY guarantees to replace all defective parts
free of charge or – at our discretion – replace the unit free of
charge provided that:
VIBRATION TOTAL VALUES (TRIAX VECTOR SUM)
ACCORDING TO EN 60745:
Screwdriving (ah, S) 0.9 m/s2, uncertainty (K) 1.5 m/s2
Drilling into metal (ah, D) 1.1m/s2, uncertainty (K) 1.5 m/s2
• The product has not been misused and has been used in
accordance with the instruction manual.
• The product has been subject to fair wear and tear;
• Repairs have not been attempted by unauthorised persons;
• Proof of purchase is produced;
• The STANLEY product is returned complete with all original
components.
If you wish to make a claim, contact your seller or check the
location of your nearest authorised STANLEY repair agent in
the STANLEY catalogue or contact your local STANLEY office
at the address indicated in this manual. A list of authorised
STANLEY repair agents and full details of our after sales
service is available on the internet at:
www.2helpU.com
13
ENGLISH
EC declaration of conformity
MACHINERY DIRECTIVE
SCD12-Drill/Screwdriver
STANLEY declares that these products described under
"technical data" are in compliance with: 2006/42/EC,
EN 60745-1:2009 + A11:2010, EN 60745-2-1:2010
EN 60745-2-2:2010
These products also comply with Directive 2004/108/EC
(until 19/04/2016) 2014/30/EU (from 20/04/2016) and 2011/65/EU.
For more information, please contact STANLEY at the following
address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of STANLEY.
R.Laverick
Engineering Manager
STANLEY , Europe, Egide Walschaertsstraat14-18,
2800 Mechelen, Belgium
08.2015
14
Download PDF