BDCDC18 | Black&Decker BDCDC18 DRILL/DRIVER Type H1 instruction manual

EN
FR
AR
10
9
8
7
6
www.blackanddecker.ae
BDCDC18
(Original instructions)
10
ENGLISH
8
9
3
2
1
5
6
7
2
6
7
4
(Original instructions)
ENGLISH
B
A
10
5
6
7
8
9
3
C
D
8
7
E
3
ENGLISH
(Original instructions)
Intended use
d. Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
Your BLACK+DECKER™ BDCDC18 - Drill, has
the power tool. Keep cord away from
been designed for screwdriving applications
heat, oil, sharp edges or moving parts.
and for drilling in wood, metal and plastics.
Damaged or entangled cords increase the
This tool is intended for consumer use only.
risk of electric shock.
Safety instructions
General power tool safety warnings
Warning! Read all safety warnings
and all instructions. Failure to
follow the warnings and instructions
listed below may result in electric shock, fire
and/or serious injury.
Save all warnings and instructions for
future reference. The term "power tool" in
all of the warnings listed below refers to
your mains operated (corded) power tool or
battery operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away
while operating a power tool.
Distractions can cause you to lose
control.
2. Electrical safety
a. Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified
plugs and matching outlets will reduce
risk of electric shock.
b. Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric
shock if your body is earthed or
grounded.
c. Do not expose power tools to rain or
wet conditions. Water entering a power
tool will increase the risk of electric
shock.
4
e. When operating a power tool outdoors,
use an extension cord suitable for
outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric
shock.
f. If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
3. Personal safety
a. Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool
while you are tired or under the
influence of drugs, alcohol or
medication. A moment of inattention
while operating power tools may result in
serious personal injury.
b. Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing
protection used for appropriate
conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your
finger on the switch or energising power
tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a
rotating part of the power tool may result
in personal injury.
e. Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in
unexpected situations.
(Original instructions)
f. Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
g. If devices are provided for the
connection of dust extraction and
collection facilities, ensure these are
connected and properly used. Use of
dust collection can reduce dust-related
hazards.
4. Power tool use and care
a. Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
b. Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the
switch is dangerous and must be
repaired.
c. Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive
safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any other
condition that may affect the power
tools operation. If damaged, have the
power tool repaired before use. Many
accidents are caused by poorly
maintained power tools.
ENGLISH
g. Use the power tool, accessories and tool
bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to be
performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5. Battery tool use and care
a. Recharge only with the charger specified
by the manufacturer. A charger that is
suitable for one type of battery pack may
create a risk of fire when used with
another battery pack.
b. Use power tools only with specifically
designated battery packs. Use of any
other battery packs may create a risk of
injury and fire.
c. When battery pack is not in use, keep it
away from other metal objects, like
paper clips, coins, keys, nails, screws, or
other small metal objects, that can make
a connection from one terminal to
another. Shorting the battery terminals
together may cause burns or a fire.
d. Under abusive conditions, liquid may be
ejected from the battery; avoid contact.
If contact accidentally occurs, flush with
water. If liquid contacts eyes,
additionally seek medical help. Liquid
ejected from the battery may cause
irritation or burns.
6. Service
a. Have your power tool serviced by a
qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool is
maintained.
Additional power tool safety
warnings
Warning! Additional safety warnings
for drills
• Use auxiliary handles supplied with the
f. Keep cutting tools sharp and clean.
tool. Loss of control can cause personal
Properly maintained cutting tools with
injury.
sharp cutting edges are less likely to bind
and are easier to control.
5
ENGLISH
(Original instructions)
• Hold power tool by insulated gripping
surfaces when performing an operation
where the cutting accessory may
contact hidden wiring. Cutting
accessory contacting a "live" wire may
make exposed metal parts of the power
tool "live" and could give the operator an
electric shock.
• Hold power tool by insulated gripping
surfaces, when performing an operation
where the fastener may contact hidden
wiring. Fasteners contacting a "live" wire
may make exposed metal parts of the
power tool "live" and could give the
operator an electric shock.
• Use clamps or another practical way to
secure and support the workpiece to a
stable platform. Holding the work by
hand or against your body leaves it
unstable and may lead to loss of control.
•
Before drilling into walls, floors or
ceilings, check for the location of wiring
and pipes.
•
Avoid touching the tip of a drill bit just
after drilling, as it may be hot.
•
The intended use is described in this
instruction manual. The use of any
accessory or attachment or performance
of any operation with this tool other than
those recommended in this instruction
manual may present a risk of personal
injury and/or damage to property.
Safety of others
•
This tool is not intended for use by
persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use
of the tool by a person responsible for
their safety.
•
Children should be supervised to ensure
that they do not play with the appliance.
safety regulations and the implementation of
safety devices, certain residual risks can not
be avoided. These include:
•
Injuries caused by touching any
rotating/moving parts.
•
Injuries caused when changing any parts,
blades or accessories.
•
Injuries caused by prolonged use of a
tool. When using any tool for prolonged
periods ensure you take regular breaks.
•
Impairment of hearing.
•
Health hazards caused by breathing dust
developed when using your tool
(example:- working with wood, especially
oak, beech and MDF.)
Vibration
The declared vibration emission values
stated in the technical data and the
declaration of conformity have been
measured in accordance with a standard test
method provided by EN 60745 and may be
used for comparing one tool with another.
The declared vibration emission value may
also be used in a preliminary assessment of
exposure.
Warning! The vibration emission value
during actual use of the power tool can
differ from the declared value depending on
the ways in which the tool is used. The
vibration level may increase above the level
stated.
When assessing vibration exposure to
determine safety measures required by
2002/44/EC to protect persons regularly
using power tools in employment, an
estimation of vibration exposure should
consider, the actual conditions of use and
the way the tool is used, including taking
account of all parts of the operating cycle
such as the times when the tool is switched
off and when it is running idle in addition to
the trigger time.
Residual risks
Labels on tool
Additional residual risks may arise when
using the tool which may not be included in
the enclosed safety warnings. These risks
can arise from misuse, prolonged use etc.
The following symbols are shown on the tool
along with the date code:
Even with the application of the relevant
6
Warning! To reduce the risk of injury,
the user must read the instruction
manual.
(Original instructions)
Additional safety instructions for
batteries and chargers (Not
provided with the tool)
Batteries
•
ENGLISH
If the supply cord is damaged, it must be
replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
•
Never attempt to open for any reason.
•
Do not expose the battery to water.
This tool includes some or all of the
following features.
•
Do not store in locations where the
temperature may exceed 40 °C.
1. Variable speed switch
•
Charge only at ambient temperatures
between 10 °C and 40 °C.
3. Torque adjustment collar
•
Charge only using the charger provided
with the tool.
•
When disposing of batteries, follow the
instructions given in the section
"Protecting the environment".
Do not attempt to charge damaged
batteries.
Chargers
•
Use your BLACK+DECKER charger only
to charge the battery in the tool with
which it was supplied. Other batteries
could burst, causing personal injury and
damage.
•
Never attempt to charge
non-rechargeable batteries.
•
Have defective cords replaced
immediately.
•
Do not expose the charger to water.
•
Do not open the charger.
•
Do not probe the charger.
The charger is intended for indoor
use only.
Read the instruction manual before
use.
Electrical safety
2. Forward/reverse slider
4. Keyless chuck
5. LED work light
6. Battery
7. Battery release button
Assembly
Use
Warning! Let the tool work at its own pace.
Do not overload.
Charging the battery (fig. A)
The battery needs to be charged before first
use and whenever it fails to produce
sufficient power on jobs that were easily
done before. The battery may become warm
while charging; this is normal and does not
indicate a problem.
Warning! Do not charge the battery at
ambient temperatures below 10 °C or above
40 °C. Recommended charging temperature:
approx. 24 °C.
Note: The charger will not charge a battery
if the cell temperature is below
approximately 10 °C or above 40 °C.
The battery should be left in the charger
and the charger will begin to charge
automatically when the cell temperature
warms up or cools down.
•
Your charger is double insulated;
therefore no earth wire is required.
Always check that the mains voltage •
corresponds to the voltage on the
rating plate. Never attempt to replace
the charger unit with a regular mains •
plug.
Plug the charger into any standard 230
Volts 50 Hz electrical outlet.
Slide the battery pack into the charger as
shown in figure A.
The green LED will flash indicating that
the battery is being charged.
7
ENGLISH
•
(Original instructions)
The completion of charge is indicated by
the green LED remaining on
continuously. The pack is fully charged
and may be used at this time or left on
the charger.
Warning! fire Hazard. When disconnecting
the charger from the tool, be sure to unplug
the charger from the outlet first, then
disconnect the charger cord from the tool.
Installing and removing the battery pack
from the tool (fig. B)
Warning! Make certain the lock-off button is
engaged to prevent switch actuation before
removing or installing battery.
To install battery pack:
•
Insert battery pack into tool, until an
audible click is heard (fig. B)
Removing the battery pack from the tool
(fig. C)
•
Depress the battery release button as
shown in (fig. C) and pull battery pack
out of tool.
Operating Instructions
Torque control (fig.D)
This tool is fitted with a torque adjustment
collar (3) to select the operating mode and
to set the torque for tightening screws.
Large screws and hard workpiece materials
require a higher torque setting than small
screws and soft workpiece materials.
•
For drilling in wood, metal and plastics,
set the collar to the drilling position
symbol
Keyless chuck (fig. E)
Warning! Make certain the lock-off button is
engaged to prevent switch actuation before
installing or removing accessories.
To insert a drill bit or other accessory:
•
Grasp the rear half of the chuck (7) with
one hand and use your other hand to
rotate the front half (8) in the
counterclockwise direction, as viewed
from the chuck end.
•
Insert the bit or other accessory fully into
the chuck, and tighten securely by
holding the rear half of the chuck and
rotating the front portion in the clockwise
direction as viewed from the chuck end.
Warning! Do not attempt to tighten drill bits
(or any other accessory) by gripping the
front part of the chuck and turning the tool
on. Damage to the chuck and personal injury
may occur when changing accessories.
Drilling/screwdriving
•
Select forward or reverse rotation using
the forward/reverse slider (2).
•
To switch the tool on, press the switch (1).
The tool speed depends on how far you
press the switch.
•
To switch the tool off, release the switch.
Hints for optimum use
Drilling
•
Use sharp drill bits only.
•
Support and secure work properly, as
instructed in the Safety Instructions.
•
Use appropriate and required safety
equipment, as instructed in the Safety
Instructions.
•
For screwdriving, set the collar to the
desired setting. If you do not yet know
the appropriate setting, proceed as
follows:
•
Set the collar to the lowest torque
setting.
•
Secure and maintain work area, as
instructed in the Safety Instructions.
•
Tighten the first screw.
•
•
If the clutch ratchets before the desired
result is achieved, increase the collar
•
setting and continue tightening the
screw. Repeat until you reach the correct
setting. Use this setting for the remaining
screws.
Run the drill very slowly, using light
pressure, until the hole is started enough
to keep the drill bit from slipping out of it.
8
Apply pressure in a straight line with the
bit. Use enough pressure to keep the bit
biting but not so much as to stall the
motor or deflect the bit.
(Original instructions)
•
Hold the drill firmly with two hands to
control its twisting action.
•
DO NOT CLICK THE TRIGGER OF A
STALLED DRILL OFF AND ON IN AN
ATTEMPT TO START IT. DAMAGE TO
THE DRILL CAN RESULT.
•
Minimize stalling on breakthrough by
reducing pressure and slowly drilling
through the last part of the hole.
•
Keep the motor running while pulling the
bit out of a drilled hole. This will help
reduce jamming.
•
Make sure switch turns drill on and off.
Drilling in wood
Holes in wood can be made with the same
twist drill bits used for metal or with spade
bits. These bits should be sharp and should
be pulled out frequently when drilling to
clear chips from the flutes.
Drilling in metal
Use a cutting lubricant when drilling metals.
The exceptions are cast iron and brass
which should be drilled dry. The cutting
lubricants that work best are sulfurized
cutting oil or lard oil.
Unit shuts off
abruptly.
ENGLISH
Battery pack has Allow battery pack to
reached its
cool down.
maximum thermal
limit.
Out of charge.
Place on charger and
(To maximize the allow to charge.
life of the battery
pack it is designed
to shutoff abruptly
when the charge is
depleted
Maintenance
Your BLACK+DECKER tool has been
designed to operate over a long period of
time with a minimum of maintenance.
Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Your charger does not require any
maintenance apart from regular cleaning.
Warning! Before performing any
maintenance on the tool, remove the battery
from the tool. Unplug the charger before
cleaning it.
•
Regularly clean the ventilation slots in
your tool and charger using a soft brush
or dry cloth.
•
Regularly clean the motor housing using
a damp cloth. Do not use any abrasive or
solvent-based cleaner.
Regularly open the chuck and tap it to
remove any dust from the interior.
Screwdriving
•
Always use the correct type and size of
screwdriver bit.
•
If screws are difficult to tighten, try
applying a small amount of washing
liquid or soap as a lubricant.
•
Always hold the tool and screwdriver bit
in a straight line with the screw
Protecting the environment
•
Troubleshooting
Problem
Possible cause
Possible solution
Unit will not
start.
Battery pack not
charged.
Check battery pack
charging requirements
Charger not
Battery pack
will not charge. plugged in.
Surrounding air
temperature too
hot or too cold.
Plug charger into a
working outlet.
Move charger and
battery pack to a
surrounding air
temperature of above
40 degrees F (45ºC)
or below 105 degrees
F (+40.5ºC)
Separate collection. This product
must not be disposed of with normal
household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or if it is of no further use to you, do
not dispose of it with household waste. Make
this product available for separate collection.
Separate collection of used products
and packaging allows materials to be
recycled and used again. Reuse of
recycled materials helps prevent environmental pollution and reduces the demand for raw
materials.
9
ENGLISH
(Original instructions)
Local regulations may provide for separate
collection of electrical products from the
household, at municipal waste sites or by
the retailer when you purchase a new
product.
Charger
Input voltage
VAC
220-240
Output voltage
VDC
18
BLACK+DECKER provides a facility for the
collection and recycling of BLACK+DECKER
products once they have reached the end of
their working life. To take advantage of this
service please return your product to any
authorised repair agent who will collect
them on our behalf.
Current
You can check the location of your nearest
authorised repair agent by contacting your
local BLACK+DECKER office at the address
indicated in this manual. Alternatively, a list
of authorised BLACK+DECKER repair
agents and full details of our after-sales
service and contacts are available on the
Internet at: www.2helpU.com.
Technical data
BDCDC18
Voltage
VDC
18
No-load speed
Min-1
0-650rpm
Max. torque
Nm
10.3/30
Chuck capacity
mm
1-10
Weight
mm
10/25
kg
0.78
(with battery
1.18)
Charger
Input voltage
VAC
220-240
Output voltage
VDC
18
Current
mA
200mA
Hours
8
Approx. charge time
10
400
3-5
Input voltage
VAC
220-240
Output voltage
VDC
18
Current
Amp
1
Approx. charge time
Hours
1.5
Charger
BL1518
Battery
Voltage
Capacity
Type
VAC
Ah
Voltage
Capacity
Type
Voltage
Capacity
Type
18
1.5
Li-Ion
BL2018
Battery
VAC
Ah
18
2.0
Li-Ion
BL4018
Battery
Max Drilling capacity
Steel/wood
mA
Hours
Approx. charge time
VAC
Ah
18
4.0
Li-Ion
(Original instructions)
ENGLISH
Guarantee
BLACK+DECKER is confident of the quality
of its products and offers an outstanding
guarantee. This guarantee statement is in
addition to and in no way prejudices your
statutory rights.
If a BLACK+DECKER product becomes
defective due to faulty materials,
workmanship or lack of conformity, within
24 months from the date of purchase,
BLACK+DECKER guarantees to replace
defective parts, repair products subjected to
fair wear and tear or replace such products
to make sure of the minimum inconvenience
to the customer unless:
•
The product has been used for trade,
professional or hire purposes.
•
The product has been subjected to
misuse or neglect.
•
The product has sustained damage
through foreign objects, substances or
accidents.
•
Repairs have been attempted by persons
other than authorised repair agents or
BLACK+DECKER service staff.
To claim on the guarantee, you will need to
submit proof of purchase to the seller or an
authorised repair agent. You can check the
location of your nearest authorised repair
agent by contacting your local
BLACK+DECKER office at the address
indicated in this manual. Alternatively, a list
of authorised BLACK+DECKER repair agents
and full details of our aftersales service and
contacts are available on the Internet at:
www.2helpU.com
11
03.2017
PLS Advice
Download PDF

advertising