DCP580 | DeWalt DCP580 PLANER instruction manual

DCP580
Final Page size: A5 (148mm x 210mm)
English (original instructions)4
Copyright DeWALT
B
Figure 1
O
B
L
A
C
K
N
J
D
I
H
E
G
F
CC
DD
D
M
L
N
G
O
N
P
1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
H
H
F
Q
F
Q
2
Figure 7
Figure 8A
S
W
T
Z
U
R
Y
Figure 8B
Figure 8C
Y
T
Z
U
U
W Z
Y X
W
R
S
W
V
Figure 9
Figure 10
BB
AA
Figure 11A
Figure 11B
EE
L
3
English
18V CORDLESS HAND PLANER
DCP580
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make
DeWALT one of the most reliable partners for professional power tool users.
Technical Data
min-1
mm
mm
kg
DCP580
18
1
Li-Ion
15,000
2
82
2.5
LPA (emission sound pressure level)
dB(A)
88
LWA(sound power level)
dB(A)
99
K (uncertainty for the given sound level)
dB(A)
3
Vibration emission value ah =
Uncertainty K =
m/s2
m/s2
<2.5
1.5
Voltage
Type
Battery type
No-load speed
Planing depth
Planing width
Weight (without battery pack)
VDC
Noise values and vibration values (triax vector sum) according to EN60745-2-14:
The vibration emission level given in this information
sheet has been measured in accordance with a
standardised test given in EN60745 and may be
used to compare one tool with another. It may be
used for a preliminary assessment of exposure.
WARNING: The declared vibration
emission level represents the main
applications of the tool. However if the
tool is used for different applications,
with different accessories or poorly
maintained, the vibration emission may
differ. This may significantly increase the
exposure level over the total working
period.
An estimation of the level of exposure to
vibration should also take into account
the times when the tool is switched off or
when it is running but not actually doing
the job. This may significantly reduce
the exposure level over the total working
period.
Identify additional safety measures to
protect the operator from the effects of
vibration such as: maintain the tool and
the accessories, keep the hands warm,
organisation of work patterns.
4
Battery pack
Battery type
Voltage
Capacity
Weight
Battery pack
Battery type
Voltage
Capacity
Weight
Charger
Mains voltage
Battery type
Approx. charging time
of battery packs
Weight
VDC
Ah
kg
DCB180
Li-Ion
18
3.0
0.64
DCB181
Li-Ion
18
1.5
0.35
DCB182
Li-Ion
18
4.0
0.61
VDC
Ah
kg
DCB183/B
Li-Ion
18
2.0
0.40/0.45
DCB184/B
Li-Ion
18
5.0
0.62/0.67
DCB185
Li-Ion
18
1.3
0.35
VAC
min
kg
DCB105
230
10.8/14.4/18 Li-Ion
25 (1.3 Ah) 30 (1.5 Ah) 40 (2.0 Ah)
55 (3.0 Ah) 70 (4.0 Ah) 90 (5.0 Ah)
0.49
English
Charger
Mains voltage
Battery type
Approx. charging time
of battery packs
Weight
Charger
Mains voltage
Battery type
Approx. charging time
of battery packs
Weight
DCB107
230
10.8/14.4/18 Li-Ion
min 60 (1.3 Ah) 70 (1.5 Ah) 90 (2.0 Ah)
140 (3.0 Ah) 185 (4.0 Ah) 240 (5.0 Ah)
kg
0.29
VAC
min
kg
Charger
Mains voltage
Battery type
Approx. charging time
of battery packs
Weight
VAC
min
kg
Charger
Mains voltage
Battery type
Approx. charging time
of battery packs
Denotes risk of electric shock.
Denotes risk of fire.
VAC
VAC
min
DCB112
230
10.8/14.4/18 Li-Ion
40 (1.3 Ah) 45 (1.5 Ah) 60 (2.0 Ah)
90 (3.0 Ah) 120 (4.0 Ah) 150 (5.0 Ah)
0.36
DCB113
230
10.8/14.4/18 Li-Ion
30 (1.3 Ah) 35 (1.5 Ah) 50 (2.0 Ah)
70 (3.0 Ah) 100 (4.0 Ah) 120 (5.0 Ah)
0.4
DCB115
230
10.8/14.4/18 Li-Ion
22 (1.3 Ah) 22 (1.5 Ah) 30 (2.0 Ah)
45 (3.0 Ah) 60 (4.0 Ah) 75 (5.0 Ah)
0.5
Weight
kg
Fuses:
Europe
U.K. & Ireland
230V tools
230V tools
10 Amperes. mains
3 Amperes. in plugs
Definitions: Safety Guidelines
The definitions below describe the level of severity
for each signal word. Please read the manual and
pay attention to these symbols.
DANGER: Indicates an imminently
hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING: Indicates a potentially
hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION: Indicates a potentially
hazardous situation which, if not avoided,
may result in minor or moderate
injury.
NOTICE: Indicates a practice not
related to personal injury which, if
not avoided, may result in property
damage.
EC-Declaration of Conformity
MACHINERY DIRECTIVE
HAND PLANER
DCP580
DeWALT declares that these products described
under Technical Data are in compliance with:
2006/42/EC, EN60745-1:2009+A11:2010,
EN60745-2-14:2009+A2:2010.
These products also comply with Directive
2004/108/EC (until 19.04.2016), 2014/30/EU (from
20.04.2016) and 2011/65/EU. For more information,
please contact DeWALT at the following address or
refer to the back of the manual.
The undersigned is responsible for compilation of
the technical file and makes this declaration on
behalf of DeWALT.
Markus Rompel
Director Engineering
DeWALT, Richard-Klinger-Straße 11,
D-65510, Idstein, Germany
15.02.2016
WARNING: To reduce the risk of injury,
read the instruction manual.
General Power Tool Safety Warnings
WARNING: Read all safety warnings
and all instructions. Failure to follow
the warnings and instructions may result
in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to
your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
5
English
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away
while operating a power tool. Distractions
can cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for
outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric
shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are
doing and use common sense when
operating a power tool. Do not use
a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your finger
6
on the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the
connection of dust extraction and
collection facilities, ensure these are
connected and properly used. Use of dust
collection can reduce dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any other
condition that may affect the power
tool’s operation. If damaged, have the
power tool repaired before use. Many
accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
English
g) Use the power tool, accessories and
tool bits etc., in accordance with these
instructions taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger
specified by the manufacturer. A charger
that is suitable for one type of battery pack
may create a risk of fire when used with
another battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any
other battery packs may create a risk of
injury and fire.
c) When battery pack is not in use, keep it
away from other metal objects like paper
clips, coins, keys, nails, screws or other
small metal objects that can make a
connection from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may
be ejected from the battery; avoid
contact. If contact accidentally occurs,
flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid
ejected from the battery may cause irritation
or burns.
6) SERVICE
a) Have your power tool serviced by
a qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool is
maintained.
Additional Specific Safety Rules for
Planers
• Wait for the cutter to stop before setting
the tool down. An exposed cutter may engage
the surface leading to possible loss of control
and serious injury.
•Use clamps or another practical way to
secure and support the workpiece to a
stable platform. Holding the work by your
hand or against the body leaves it unstable and
may lead to loss of control.
•Wear a dust mask.
•Hold the power tool by insulated gripping
surfaces only, because the cutter may
contact its hidden wiring. Cutting a "live" wire
may make exposed metal parts of the power
tool "live" and could give the operator an electric
shock.
Residual Risks
In spite of the application of the relevant safety
regulations and the implementation of safety
devices, certain residual risks cannot be avoided.
These are:
– Impairment of hearing.
– Risk of personal injury due to flying particles.
– Risk of burns due to accessories becoming hot
during operation.
– Risk of personal injury due to prolonged use.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
DATE CODE POSITION (FIG. 1)
The date code (CC), which also includes the year of
manufacture, is printed into the housing.
Example:
2016 XX XX
Year of Manufacture
Important Safety Instructions for All
Battery Chargers
SAVE THESE INSTRUCTIONS: This manual
contains important safety and operating
instructions for compatible battery chargers (refer to
Technical Data).
• Before using charger, read all instructions and
cautionary markings on charger, battery pack,
and product using battery pack.
WARNING: Shock hazard. Do not allow
any liquid to get inside charger. Electric
shock may result.
WARNING: We recommend the use of
a residual current device with a residual
current rating of 30mA or less.
CAUTION: Burn hazard. To reduce
the risk of injury, charge only DeWALT
rechargeable batteries. Other types of
batteries may burst causing personal
injury and damage.
7
English
CAUTION: Children should be
supervised to ensure that they do not
play with the appliance.
NOTICE: Under certain conditions,
with the charger plugged into the power
supply, the exposed charging contacts
inside the charger can be shorted by
foreign material. Foreign materials of
a conductive nature such as, but not
limited to, steel wool, aluminum foil or
any buildup of metallic particles should
be kept away from charger cavities.
Always unplug the charger from the
power supply when there is no battery
pack in the cavity. Unplug charger before
attempting to clean
• DO NOT attempt to charge the battery
pack with any chargers other than the
ones in this manual. The charger and battery
pack are specifically designed to work together.
• These chargers are not intended for
any uses other than charging DeWALT
rechargeable batteries. Any other uses
may result in risk of fire, electric shock or
electrocution.
• Do not expose charger to rain or snow.
• Pull by plug rather than cord when
disconnecting charger. This will reduce risk
of damage to electric plug and cord.
• Make sure that cord is located so that it
will not be stepped on, tripped over, or
otherwise subjected to damage or stress.
• Do not use an extension cord unless it
is absolutely necessary. Use of improper
extension cord could result in risk of fire,
electric shock, or electrocution.
• Do not place any object on top of charger
or place the charger on a soft surface that
might block the ventilation slots and result
in excessive internal heat. Place the charger
in a position away from any heat source. The
charger is ventilated through slots in the top and
the bottom of the housing.
• Do not operate charger with damaged cord
or plug—have them replaced immediately.
•Do not operate charger if it has received
a sharp blow, been dropped, or otherwise
damaged in any way. Take it to an authorised
service centre.
• Do not disassemble charger; take it to an
authorised service centre when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock, electrocution or
fire.
8
• In case of damaged power supply cord the
supply cord must be replaced immediately by
the manufacturer, its service agent or similar
qualified person to prevent any hazard.
• Disconnect the charger from the outlet
before attempting any cleaning. This will
reduce the risk of electric shock. Removing
the battery pack will not reduce this risk.
•NEVER attempt to connect two chargers
together.
• The charger is designed to operate on
standard 230V household electrical power.
Do not attempt to use it on any other
voltage. This does not apply to the vehicular
charger.
SAVE THESE INSTRUCTIONS
Chargers
The DCB105, DCB107, DCB112, DCB113 and
DCB115 chargers accept 10.8V, 14.4V and 18V
Li-Ion XR (DCB140, DCB141, DCB142, DCB143,
DCB144, DCB145, DCB180, DCB181, DCB182,
DCB183, DCB183B, DCB184, DCB184B and
DCB185) battery packs.
DeWALT chargers require no adjustment and are
designed to be as easy as possible to operate.
Charging Procedure (Fig. 1)
1.Plug the charger into an appropriate outlet
before inserting battery pack.
2.Insert the battery pack (N) into the charger.
The red (charging) light will blink continuously
indicating that the charging process has
started.
3.The completion of charge will be indicated by
the red light remaining ON continuously. The
pack is fully charged and may be used at this
time or left in the charger.
NOTE: To ensure maximum performance and life
of lithium-ion batteries, charge the battery pack fully
before first use.
Charging Process
Refer to the table below for the charge status of the
battery pack.
Charge indicators: DCB105
charging
fully charged
hot/cold pack delay
replace battery pack
English
Charge indicators: DCB107, DCB112, DCB113, DCB115
charging
fully charged
hot/cold pack delay*
*DCB107, DCB112, DCB113, DCB115: The red
light will continue to blink, but a yellow indicator
light will be illuminated during this operation.
Once the battery has reached an appropriate
temperature, the yellow light will turn off and the
charger will resume the charging procedure.
The compatible charger(s) will not charge a faulty
battery pack. The charger will indicate faulty battery
by refusing to light or by displaying problem pack or
charger blink pattern.
NOTE: This could also mean a problem with a
charger.
If the charger indicates a problem, take the charger
and battery pack to be tested at an authorised
service centre.
• Do not charge or use battery in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Inserting
or removing the battery from the charger may
ignite the dust or fumes.
• Never force battery pack into charger. Do
not modify battery pack in any way to fit
into a non-compatible charger as battery
pack may rupture causing serious personal
injury.
• Charge the battery packs only in DeWALT
chargers.
• DO NOT splash or immerse in water or other
liquids.
• Do not store or use the tool and battery
pack in locations where the temperature
may reach or exceed 40 ˚C (104 ˚F) (such
as outside sheds or metal buildings in
summer).
WARNING: Never attempt to open the
battery pack for any reason. If battery
pack case is cracked or damaged,
do not insert into charger. Do not
crush, drop or damage battery pack.
Do not use a battery pack or charger
that has received a sharp blow, been
dropped, run over or damaged in any
way (i.e., pierced with a nail, hit with a
hammer, stepped on). Electric shock
or electrocution may result. Damaged
battery packs should be returned to
service centre for recycling.
CAUTION: When not in use, place
tool on its side on a stable surface
where it will not cause a tripping or
falling hazard. Some tools with large
battery packs will stand upright on the
battery pack but may be easily knocked
over.
HOT/COLD PACK DELAY
When the charger detects a battery that is too hot
or too cold, it automatically starts a Hot/Cold Pack
Delay, suspending charging until the battery has
reached an appropriate temperature. The charger
then automatically switches to the pack charging
mode. This feature ensures maximum battery life.
A cold battery pack will charge at about half the
rate of a warm battery pack. The battery pack will
charge at that slower rate throughout the entire
charging cycle and will not return to maximum
charge rate even if the battery warms.
LITHIUM-ION BATTERY PACKS ONLY
XR Li-Ion tools are designed with an Electronic
Protection System that will protect the battery
against overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic
Protection System engages. If this occurs, place
the lithium-ion battery on the charger until it is fully
charged.
Important Safety Instructions for All
Battery Packs
When ordering replacement battery packs, be sure
to include catalog number and voltage.
The battery pack is not fully charged out of the
carton. Before using the battery pack and charger,
read the safety instructions below. Then follow
charging procedures outlined.
READ ALL INSTRUCTIONS
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM-ION
(LI-ION)
• Do not incinerate the battery pack even
if it is severely damaged or is completely
worn out. The battery pack can explode in
a fire. Toxic fumes and materials are created
when lithium-ion battery packs are burned.
• If battery contents come into contact
with the skin, immediately wash area with
mild soap and water. If battery liquid gets
into the eye, rinse water over the open eye for
15 minutes or until irritation ceases. If medical
attention is needed, the battery electrolyte
is composed of a mixture of liquid organic
carbonates and lithium salts.
9
English
• Contents of opened battery cells may
cause respiratory irritation. Provide fresh air.
If symptoms persists, seek medical attention.
WARNING: Burn hazard. Battery liquid
may be flammable if exposed to spark or
flame.
Transportation
DeWALT batteries comply with all applicable
shipping regulations as prescribed by industry
and legal standards which include UN
Recommendations on the Transport of Dangerous
Goods; International Air Transport Association
(IATA) Dangerous Goods Regulations, International
Maritime Dangerous Goods (IMDG) Regulations,
and the European Agreement Concerning The
International Carriage of Dangerous Goods by Road
(ADR). Lithium-ion cells and batteries have been
tested to section 38.3 of the UN Recommendations
on the Transport of Dangerous Goods Manual of
Tests and Criteria.
In most instances, shipping a DeWALT battery pack
will be excepted from being classified as a fully
regulated Class 9 Hazardous Material. In general,
the two instances that require shipping Class 9 are:
1.Air shipping more than two DeWALT lithium-ion
battery packs when the package contains only
battery packs (no tools), and
2.Any shipment containing a lithium-ion battery
with an energy rating greater than 100 watt
hours (Wh). All lithium-ion batteries have the
watt hour rating marked on the pack.
Regardless of whether a shipment is considered
excepted or fully regulated, it is the shipper's
responsibility to consult the latest regulations for
packaging, labeling/marking and documentation
requirements.
Transporting batteries can possibly cause fire if the
battery terminals inadvertently come in contact with
conductive materials. When transporting batteries,
make sure that the battery terminals are protected
and well insulated from materials that could contact
them and cause a short circuit.
The information provided in this section of the
manual is provided in good faith and believed to be
accurate at the time the document was created.
However, no warranty, expressed or implied, is
given. It is the buyer’s responsibility to ensure that its
activities comply with the applicable regulations.
Battery Pack
BATTERY TYPE
The DCP580 operates on an 18 volt battery pack.
10
The DCB180, DCB181, DCB182, DCB183,
DCB183B, DCB184, DCB184B or DCB185 battery
packs may be used. Refer to Technical Data for
more information.
Storage Recommendations
1.The best storage place is one that is cool and
dry away from direct sunlight and excess heat
or cold. For optimum battery performance and
life, store battery packs at room temperature
when not in use.
2.For long storage, it is recommended to store a
fully charged battery pack in a cool, dry place
out of the charger for optimal results.
NOTE: Battery packs should not be stored
completely depleted of charge. The battery pack will
need to be recharged before use.
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual,
the labels on the charger and the battery pack may
show the following pictographs:
Read instruction manual before use.
See Technical Data for charging time.
Battery charging.
Battery charged.
Battery defective.
Hot/cold pack delay.
Do not probe with conductive objects.
Do not charge damaged battery packs.
Do not expose to water.
Have defective cords replaced
immediately.
Charge only between 4 ˚C and 40 ˚C.
Only for indoor use.
English
Discard the battery pack with due care
for the environment.
Charge DeWALT battery packs only with
designated DeWALT chargers. Charging
battery packs other than the designated
DeWALT batteries with a DeWALT
charger may make them burst or lead to
other dangerous situations.
Do not incinerate the battery pack.
Package Contents
The package contains:
1Planer
1 Parallel fence
1T25 star key
1 Gauge plate
1 Dustbag (kitted models only)
2 Li-Ion battery packs (kitted models only)
1 TSTAK kitbox (kitted models only)
1 Instruction manual
• Check for damage to the tool, parts or
accessories which may have occurred
during transport.
• Take the time to thoroughly read and
understand this manual prior to operation.
Description (Fig. 1)
WARNING: Never modify the power
tool or any part of it. Damage or personal
injury could result.
A.Trigger switch
B.Lock-off button
C.Main handle
D.Rear shoe
E.Drive belt cover
F.Hole for rebate fence
G.Front shoe
H.Rebate fence tightening knob
I.Planing depth graduation
J.Planing depth adjustment knob/ front handle
K.Chip ejection port
L.AirLock connection
M.Blade storage knob
N.Battery
O.Battery release button
INTENDED USE
Your planer has been designed for professional
planing of wood.
DO NOT use under wet conditions or in the
presence of flammable liquids or gases.
This planer is a professional power tool.
DO NOT let children come into contact with the
tool. Supervision is required when inexperienced
operators use this tool.
•Young children and the infirm. This appliance
is not intended for use by young children or
infirm persons without supervision.
• This product is not intended for use by persons
(including children) suffering from diminished
physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are
supervised by a person responsible for their
safety. Children should never be left alone with
this product.
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the battery pack
voltage corresponds to the voltage on the rating
plate. Also make sure that the voltage of your
charger corresponds to that of your mains.
Your DeWALT charger is double insulated
in accordance with EN60335; therefore
no earth wire is required.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
DeWALT service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in
the plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 3 A.
Using an Extension Cable
An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see Technical Data). The minimum conductor size
is 1 mm2; the maximum length is 30 m.
P.Fuel gauge button
11
English
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up can
cause injury.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up can
cause injury.
WARNING: Use only DeWALT battery
packs and chargers.
Inserting and Removing the
Battery Pack from the Tool (Fig. 1)
NOTE: Make sure your battery pack (N) is fully
charged.
TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE
1.Align the battery pack (N) with the rails inside
the tool’s handle (Fig. 1).
2.Slide it into the handle until the battery pack is
firmly seated in the tool and ensure that you
hear the lock snap into place.
TO REMOVE THE BATTERY PACK FROM THE TOOL
1.Press the release button (O) and firmly pull the
battery pack out of the tool handle.
2.Insert battery pack into the charger as
described in the charger section of this manual.
FUEL GAUGE BATTERY PACKS (FIG. 1)
Some DeWALT battery packs include a fuel gauge
which consists of three green LED lights that
indicate the level of charge remaining in the battery
pack.
To actuate the fuel gauge, press and hold the fuel
gauge button (P). A combination of the three green
LED lights will illuminate designating the level of
charge left. When the level of charge in the battery
is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
NOTE: The fuel gauge is only an indication of the
charge left on the battery pack. It does not indicate
tool functionality and is subject to variation based
on product components, temperature and end-user
application.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
12
Proper Hand Position (Fig. 2)
WARNING: To reduce the risk of serious
personal injury, ALWAYS use proper
hand position as shown.
WARNING: To reduce the risk of serious
personal injury, ALWAYS hold securely in
anticipation of a sudden reaction.
Proper hand position requires one hand on the front
handle (J), with the other hand on the main handle
(C).
Trigger Switch (Fig. 1)
WARNING: This tool has no provision
to lock the switch in the ON position
and shoud never be locked ON by any
other means.
Release the trigger switch lock-off button (B) by
pressing the button as shown. Pull the trigger switch
(A) to turn the motor on. Releasing the switch turns
the motor off.
CAUTION: Allow the tool to reach full
speed before touching tool to the work
surface. Lift the tool from the work
surface before turning the tool off.
To start the planer depress the trigger switch (A).
To turn the planer off, release the trigger switch.
Adjusting the Planing Depth (Fig. 1)
To adjust the depth of cut, turn the planing depth
adjustment knob (J). Each click is equal to 0.1 mm
of depth up to the maximum depth of cut of
approximately 2.0 mm (5/64").
It is recom­mended that test cuts be made in scrap
wood after each re-adjustment to make sure that
the desired amount of wood is being removed by
the planer. Several shallow passes (rather than one
deep one) will produce a smoother finish.
Planing (Fig. 1, 2–4)
CAUTION: Allow the tool to reach full
speed before touching tool to the work
surface. Lift the tool from the work
surface before turning the tool off.
Hold the planer in the correct position with one
hand on the front handle (J) and the other hand on
the main handle (C) as shown in Figure 2. Place the
front shoe (G) on the surface to be planed, making
certain that the cutting blades are not touching the
English
surface. Push down firmly on the front handle of the
planer so that the front shoe is ABSOLUTELY FLAT
on the work surface. Squeeze the trigger switch and
allow the motor to reach full speed before touching
the planer blades to the work surface.
Move the tool slowly into the work and maintain
downward pressure to keep the planer flat. Be
particularly careful to keep the tool flat at the
beginning and the end of the work surface.
Planing Tip: For a smoother appearance, fasten a
piece of scrap wood to the end of the piece you are
planing. Don’t stop planing until the cutting blades
of the planer are past your workpiece and into the
scrap material.
Rebate Fence (Fig. 5, 6)
WARNING: Allow the tool to reach
full speed before touching tool to the
work surface. Lift the tool from the work
surface before turning the tool off.
The rebate fence (Q) is used for optimum tool
control on narrow workpieces and can be installed
on either side of your planer. The planer makes
rebate cuts up to 9 mm (23/64").
TO INSTALL REBATE FENCE
1.Loosen the rebate fence tightening knob (H).
2.Slide the crossbar on the rebate fence (Q) into
the hole (F) on the side of the planer as shown
in Figure 5.
3.Set the width of cut by adjusting the edge guide
across the width of the shoe.
4.Securely tighten rebate fence tightening knob
(H).
NOTE: The rebate fence should be below the
planer when installed correctly as shown in Figure 6.
TO MAKE A REBATE CUT
1.Turn the rebate fence tightening knob (H) to
adjust the desired width of cut.
2.Make several cuts until the desired depth is
reached.
NOTE: It will be necessary to make quite a few cuts
for most rebate applications.
To Change Blades (Fig. 8A–8C)
WARNING: To reduce the risk of
serious personal injury, turn tool
off and remove the battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up can
cause injury.
CAUTION: Planer blades are extremely
sharp. Handle with great care.
This planer uses carbide blades.
BLADE STORAGE (FIG. 7)
Your planer is equipped with blade storage for two
additional blades. To store or remove additional
blades, turn the blade storage knob (M) counter
clockwise to open.
REVERSIBLE CARBIDE BLADES (FIG. 8A-C)
1.To Remove Blade from Planer (Fig. 8B)
a.Loosen and remove the three star-head
screws (R) with the T25 star key (DD)
provided. Remove the drum cover (S) from
the drum (T).
b.Remove the blade carrier/guide bar
assembly (U, W, Z). Carefully remove the
carbide blade (Y).
2.To Adjust Blade Using Gauge Plate
(provided with tool) (Fig. 8C)
a.Cautiously place the sharp edge of the
carbide blade (Y) on the gauge plate (V) with
the grooved side of the carbide blade facing
up. Either edge of the reversible carbide
blade can be set flush against the gauge
plate inside wall (X).
b.Place the blade carrier/guide bar assembly
on the blade so that the rib on the blade
carrier (Z) fits into the groove on the carbide
blade (Y). The heel of the guide bar (W) will
over-hang the end of the gauge plate (V).
c.Loosen the two cross-shaped screws (U)
with a screwdriver.
d.Simultaneously hold the blade carrier (Z)
and blade (Y) against the gauge plate inside
wall (X) while holding the heel of the guide
bar (W) against the back edge of the gauge
plate. Securely tighten the cross shaped
screws (U).
3.To Reinstall Blade (Fig. 8A, 8C)
a.Remove the adjusted blade carrier/guide
bar assembly from the gauge plate (V) and
place the heel of the guide bar (W) into the
groove on the drum (T).
b.Place the drum cover (S) over the blade
carrier/guide bar assembly. Loosely screw
the three hex screws (R) into the drum (T)
so that there is a small gap between the
drum and the blade carrier (Z).
c.Slide the carbide blade between the drum
(T) and the blade carrier (Z) from the side so
that the rib on the blade carrier sets into the
groove in the blade.
13
English
d.Centre the carbide blade (Y) under the
blade carrier (Z) making sure the blade is
clear of the tool housing on both sides.
e.Securely tighten the three star head screws
(R) to the drum.
4.Repeat procedure for the other blade.
NOTE: If your planer is not fitted with carbide
blades, the blade carrier (Z) required for carbide
blades is available at additional cost from your local
DeWALT authorised service centre.
You may notice that all the dust will not come
free from the bag. This will not affect planing
performance but will reduce the planer’s dust
collection efficiency. To restore your planer’s dust
collection efficiency, depress the spring inside the
dust bag when you are emptying it and tap it on the
side of a dustbin.
NOTE: A DeWALT AirLock Adapter (DWV9000) can
be purchased separately to connect a shop vacuum
or DeWALT dust extractor to your planer.
Kickstand (Fig. 9)
Your planer is equipped with a kickstand (AA) that
automatically lowers when the tool is lifted from the
work surface allowing the planer to set on the work
surface without the blade touching it. When planing,
the kickstand raises as the tool is pushed forward
through the material. If the kickstand obstructs
special planing work, it can be stored and locked
out of the way.
WARNING: Be sure that the kickstand
is correctly extended when setting the
planer on a work surface.
MAINTENANCE
Your DeWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular
cleaning.
Edge Chamfering (Fig. 10)
Your planer has a precision machined chamfering
groove (BB) in the front shoe for planing along a
corner of the wood. The width of the groove is 4.5
to 8 mm. It’s a good idea to try a piece of scrap
wood before doing finish work.
Dust Extraction (Fig. 1, 11A, 11B)
Your planer has a built-in AirLock connection
(Fig. 11A, L) which allows either a dust bag or a
shop vacuum to be connected. The built-in outlet
utilizes the DeWALT AirLock connection system
making it compatible with the DeWALT dust
extractor.
TO ATTACH THE DUST BAG
While holding the planer, slide the dust bag collar
onto the AirLock connection (L) as shown in
Figure 11.
2.Twist the chip deflector (Fig. 11B, EE) away
from the dust bag to separate.
3. Gently shake or tap the dust bag to empty.
4. Reattach the dust bag back onto the AirLock
connection.
14
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up can
cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
TO EMPTY THE DUST BAG
1.While holding the planer, remove the dust bag
by sliding it off the AirLock connection (L).
CAUTION: Never operate these tools
unless the dust collector is in place.
Planing dust exhaust may create a
breathing hazard.
English
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect
the charger from the AC outlet before
cleaning. Dirt and grease may be
removed from the exterior of the charger
using a cloth or soft non-metallic brush.
Do not use water or any cleaning
solutions.
CHIP EJECTION PORT CLEANING INSTRUCTIONS
If the unit is clogged with dust or chips, use a nonmetallic stick to push the obstruction out of the chip
ejection port (K). Never stick your finger into the
port.
Optional Accessories
WARNING: Since accessories, other
than those offered by DeWALT, have not
been tested with this product, use of
such accessories with this tool could be
hazardous. To reduce the risk of injury,
only DeWALT recommended accessories
should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. Products and
batteries marked with this symbol must
not be disposed of with normal household
waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for
raw materials. Please recycle electrical products
and batteries according to local provisions. Further
information is available at www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when
it fails to produce sufficient power on jobs which
were easily done before. At the end of its technical
life, discard it with due care for our environment:
• Run the battery pack down completely, then
remove it from the tool.
• Lithium-ion cells are recyclable. Take them to
your dealer or a local recycling station. The
collected battery packs will be recycled or
disposed of properly.
15
16
17
Belgique et
Luxembourg België
en Luxemburg
DeWALT - Belgium BVBA
Egide Walschaertsstraat 16
2800 Mechelen
Tel: NL 32 15 47 37 63
Tel: FR 32 15 47 37 64
Fax: 32 15 47 37 99
www.dewalt.be
enduser.BE@SBDinc.com
Danmark
DeWALT
Roskildevej 22
2620 Albertslund
Tel: 70 20 15 10
Fax: 70 22 49 10
www.dewalt.dk
kundeservice.dk@sbdinc.com
Deutschland
DeWALT
Richard Klinger Str. 11
65510 Idstein
Tel:06126-21-1
Fax:06126-21-2770
www.dewalt.de
infodwge@sbdinc.com
Ελλάς
DeWALT (Ελλάς) Α.Ε.
Τηλ: 00302108981616
EΔΡΑ-ΓΡΑΦΕΙΑ : Στράβωνος 7
Φαξ: 00302108983570
& Λ. Βουλιαγμένης, Γλυφάδα 166 74, Αθήνα
SERVICE : Ημερος Τόπος 2 (Χάνι Αδάμ) –
193 00 Ασπρόπυργος
www.dewalt.gr
Greece.Service@sbdinc.com
España
DeWALT Ibérica, S.C.A.
Parc de Negocios “Mas Blau”
Edificio Muntadas, c/Bergadá, 1, Of. A6
08820 El Prat de Llobregat (Barcelona)
Tel: 934 797 400
Fax: 934 797 419
www.dewalt.es
respuesta.postventa@sbdinc.
com
France
DeWALT
5, allée des Hêtres
BP 30084, 69579 Limonest Cedex
Tel: 04 72 20 39 20
Fax: 04 72 20 39 00
www.dewalt.fr
scufr@sbdinc.com
Schweiz
Suisse
Svizzera
DeWALT
In der Luberzen 42
8902 Urdorf
Tel: 044 - 755 60 70
Fax: 044 - 730 70 67
www.dewalt.ch
service@rofoag.ch
Ireland
DeWALT
Calpe House Rock Hill
Black Rock, Co. Dublin
Tel:00353-2781800
Fax:00353-2781811
www.dewalt.ie
Italia
DeWALT
via Energypark
20871 Vimercate (MB), IT
Tel: 800-014353
39 039 9590200
Fax: 39 039 9590313
www.dewalt.it
Nederlands
DeWALT Netherlands BV
Tel: 31 164 283 063
Fax: 31 164 283 200
Holtum Noordweg 35
6121 RE BORN, Postbus 83, 6120 AB BORN
www.dewalt.nl
Norge
DeWALT
Postboks 4613, Nydalen
0405 Oslo
Tel: 45 25 13 00
Fax: 45 25 08 00
www.dewalt.no
kundeservice.no@sbdinc.com
Österreich
DeWALT
Werkzeug Vertriebsges m.b.H
Oberlaaerstrasse 248, A-1230 Wien
Tel: 01 - 66116 - 0
Fax: 01 - 66116 - 614
www.dewalt.at
service.austria@sbdinc.com
Portugal
DeWALT Limited, SARL
Tel: 214 66 75 00
Centro de Escritórios de Sintra Avenida
Fax: 214 66 75 80
Almirante Gago Coutinho, 132/134, Edifício 14
2710-418 Sintra
www.dewalt.pt
resposta.posvenda@sbdinc.com
Suomi
DeWALT
PL 47
00521 Helsinki
Puh: 010 400 4333
Faksi:0800 411 340
www.dewalt.fi
asiakaspalvelu.fi@sbdinc.com
Sverige
DeWALT
Box 94
431 22 Mölndal
Tel: 031 68 61 60
Fax: 031 68 60 08
www.dewalt.se
kundservice.se@sbdinc.com
Türkiye
KALE Hırdavat ve Makina A.Ş.
Defterdar Mah. Savaklar Cad. No:15
Edirnekapı / Eyüp / İSTANBUL 34050
TÜRKİYE
Tel: 0212 533 52 55
Faks: 0212 533 10 05
www.dewalt.com.tr
United
Kingdom
DeWALT, 210 Bath Road;
Slough, Berks SL1 3YD
Tel: 01753-567055
Fax: 01753-572112
www.dewalt.co.uk
emeaservice@sbdinc.com
Australia
DeWALT
82 Taryn Drive, Epping
VIC 3076 Australia
Tel: Aust 1800 338 002
Tel: NZ 0800 339 258
www.dewalt.com.au
www.dewalt.co.nz
Middle East Africa
DeWALT
P.O. Box - 17164,
Jebel Ali Free Zone (South), Dubai, UAE
Tel: 971 4 812 7400
Fax: 971 4 2822765
www.dewalt.ae
Service.MEA@sbdinc.com
N453119
01/16
Download PDF

advertising