STMT78401-8 | Stanley STMT78401-8 RATCHET instruction manual

Manual size: 145W x 210H mm
Spread size: 290W x 210H mm
OUTSIDE
3/8" AIR RATCHET
STMT78401-8
C
B
E
3/8" AIR RATCHET
I
D
H
F
A
L
G
K
J
Serial Number
Parts Number
Description
Q'ty
A
K45021
Ratchet Housing repair kit
1
B
45015
Locking Nut
1
C
K15014
Gear repair kit
1
D
15012
Thread Ring Gear
1
E
45013
Washer
1
F
K15014
Cylinder repair kit
1
G
75020
Exhaust Deflector
1
H
45055
O-Ring
1
I
K75001
Housing repair kit
1
J
75018
Housing grip
1
K
K66024
Air Inlet repair kit
1
L
75003
Trigger
1
IT IS ADVISABLE TO:
CAREFULLY READ THE INSTRUCTIONS BEFORE USING THE PNEUMATIC TOOLS
WEAR SAFETY GOGGLES AND HEARING PROTECTION
INSIDE
STANLEY® PNEUMATIC TOOL USER GUIDE
Maintenance Notifications:
Use the specified lubricant to lubricate the tool.
Technical Notifications:
Make use of the filler while conducting lubrication and limit the flow to two (2) drops per minute.
STMT78401-8
Forward 1
Forward 2
If the filler is unavailable, lubrication should be conducted whilst rotating the tool every one (1) to two (2)
minutes until it is complete.
Forward 3
Torque ft-lb
RPM
Torque ft-lb
RPM
Torque ft-lb
RPM
30
85
48
107
60
180
The life span and performance of the tool will be greatly improved if the aforementioned steps are taken.
This tool has been designed to drive fasteners with specific impact sockets;
using standard sockets could cause injuries to the operator.
NEVER USE STANDARD SOCKETS ON IMPACT TOOLS
Thoroughly read and understand the user manual before attempting to operate
the tool.
Any attempt to alter the structural design and mechanics of the tool may result in
grievous bodily harm.
The tool must be used accurately to comply with the design parameters and usage range.
Care for the tool by conducting regular inspections.
Do not directly point the tool at any living object.
Safety precautions must be taken into account during usage, removal and storage of the tool.
Take note of potential hazards in the surrounding environment, such as people and objects, while
operating the tool.
Use the appropriate tool based on the working application and capacity.
Consistently wear protective gear, such as safety goggles, ear plugs, and mask, while
operating the tool. The use of protective gear is also advisable while repairing or
changing the tool’s spare parts.
Long hair must be tied back and it is advisable to remove all adornments including,
but not limited to scarves, neckties, and clothing with loose sleeves, to avoid any
interference with the tool.
Take note of the air supply system and air tube connection
Keep the tube from bursting by checking the air pressure before operating the tool.
Do not make direct contact with any part of the transmission while the tool is
in operation.
Avoid intertwining or running over the tube.
Ensure that the air supply is clean and dry before use.
Only purchase and use original Stanley spare parts in order to maintain the precision
and accuracy of the tool.
Regularly clean the air compressor and tube to optimize the life span of the tool.
More Than 1/100 Slope
Stop Valve
Filter Regulator
Lubricator
Main Line =3 Times
Tool Inlet/hose Size
Branch Line =2 Times
Tool Inlet/hose Size
Operating the air tool will deliver strong back throw; please stabilize yourself with
equal strength
During repair and maintenance or when not in use, turn off the air compressor and
remove the tool from the air source.
Stop Valve
Ensure that the air tube is not placed in an area with high foot traffic.
Auto Drain
Valve
Air Tool
Air Compressor
Auto Drain Valve
Should bodily irritation, numbness, or fatigue occur at any time during the operation
of the tool, seek immediate medical attention.
Download PDF

advertising