DCB132 | DeWalt DCB132 CHARGER instruction manual

DCB132
FINAL PRINT SIZE: A6 (105mm x 148mm)
English (original instructions)2
Copyright DeWALT
B
Figure 1
A
1
E N GL I S H
XR LITHIUM-ION DUAL CHARGER
DCB132
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough
product development and innovation make DeWALT one of the most
reliable partners for professional power tool users.
Technical Data
Charger
DCB132
Output
VDC
10.8, 14.4, 18
Mains voltage
VAC230
Type
1
Battery type
Li-Ion
Approx. charging
min
22
22
30
time of battery packs
(1.3 Ah)
(1.5 Ah)
(2.0 Ah)
60
75
90
(4.0 Ah)
(5.0 Ah)
(6.0 Ah)
Charger Current
Input
A
1.5
Single port output A
4.0
Weightkg
1.2
Fuses
Europe
U.K. & Ireland
230 V tools
230 V tools
45
(3.0 Ah)
140
(9.0 Ah)
10 Amperes, mains
3 Amperes, in plugs
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal word.
Please read the manual and pay attention to these symbols.
2
DANGER: Indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
ENGLISH
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderate injury.
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may result in
property damage.
Denotes risk of electric shock.
Denotes risk of fire.
WARNING: To reduce the risk of injury, read the
instruction manual.
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
Important Safety Instructions for All Battery
Chargers
• Before using charger, read all instructions
and cautionary markings on charger, battery
pack, and product using battery pack.
WARNING: Shock hazard. Do not
allow any liquid to get inside charger.
Electric shock may result.
3
E N GL I S H
WARNING: We recommend the use of
a residual current device with a residual
current rating of 30mA or less.
CAUTION: Burn hazard. To reduce
the risk of injury, charge only DeWALT
rechargeable batteries. Other types of
batteries may burst causing personal
injury and damage.
CAUTION: Children should be
supervised to ensure that they do not
play with the appliance.
NOTICE: Under certain conditions,
with the charger plugged in to the
power supply, the charger can be
shorted by foreign material. Foreign
materials of a conductive nature such
as, but not limited to, grinding dust,
metal chips, steel wool, aluminum foil,
or any buildup of metallic particles
should be kept away from charger
cavities. Always unplug the charger
from the power supply when there is
no battery pack in the cavity. Unplug
charger before attempting to clean.
• Young children and the infirm. This appliance
is not intended for use by young children or
infirm persons without supervision.
4
ENGLISH
• This product is not intended for use by
persons (including children) suffering from
diminished physical, sensory or mental
abilities, or for lack of experience and/or for
want of knowledge or skills unless they are
supervised by a person responsible for their
safety. Children should never be left alone to
play with this product.
• DO NOT attempt to charge the battery
pack with any chargers other than the
ones in this manual. The charger and
battery pack are specifically designed to
work together.
• These chargers are not intended for
any uses other than charging DeWALT
rechargeable batteries. Any other uses
may result in risk of fire, electric shock
or electrocution.
• Do not expose charger to rain or snow.
• Pull by plug rather than cord when
disconnecting charger. This will reduce risk
of damage to electric plug and cord.
• Make sure that cord is located so that
it will not be stepped on, tripped over,
or otherwise subjected to damage
or stress.
• Do not use an extension cord unless it
is absolutely necessary. Use of improper
5
E N GL I S H
extension cord could result in risk of
fire,electric shock, or electrocution.
• Do not place any object on top of
charger or place the charger on a soft
surface that might block the ventilation
slots and result in excessive internal
heat. Place the charger in a position away
from any heat source. The charger is
ventilated through slots in the top and the
bottom of the housing.
• Do not operate charger with
damaged cord or plug — have them
replaced immediately.
•Do not operate charger if it has received
a sharp blow, been dropped, or
otherwise damaged in any way. Take it to
an authorised service centre.
• Do not disassemble charger; take it to an
authorised service centre when service
or repair is required. Incorrect reassembly
may result in a risk of electric shock,
electrocution or fire.
• In case of damaged power supply cord the
supply cord must be replaced immediately
by the manufacturer, its service agent
or similar qualified person to prevent
any hazard.
6
ENGLISH
• Disconnect the charger from the outlet
before attempting any cleaning. This
will reduce the risk of electric shock.
Removing the battery pack will not reduce
this risk.
•NEVER attempt to connect 2
chargers together.
• The charger is designed to operate on
standard 230V household electrical
power. Do not attempt to use it on any
other voltage. This does not apply to the
vehicular charger.
• Take care to ensure that the charger is
standing in a steady, secure position. A
falling battery or charger may present a risk
of injury to yourself and/or others.
SAVE THESE INSTRUCTIONS
Chargers
The DCB132 charger accepts 10,8V, 14,4V, 18V Li-Ion XR and XR
FLEXVOLT battery packs (DCB123, DCB125, DCB127, DCB141,
DCB142, DCB143, DCB144, DCB145, DCB181, DCB182, DCB183,
DCB183B, DCB184, DCB184B, DCB185, DCB546, DCB547).
DeWALT chargers require no adjustment and are designed to be as
easy as possible to operate.
Charging a Battery (Fig. 1)
1.Plug the charger into an appropriate outlet before inserting
battery pack.
7
E N GL I S H
2.Insert the battery pack into the charger. The red (charging) light will
blink continuously indicating that the charging process has started.
3.The completion of charge will be indicated by the red light
remaining ON continuously. The pack is fully charged and may be
used at this time or left in the charger.
NOTE: To ensure maximum performance and life of lithium-ion battery
packs, charge the battery pack fully before first use.
Charger Operation
Refer to the table below for the charge status of the battery pack.
Charge Indicators
Charging
Fully Charged
Hot/Cold Pack Delay*
*The red light will continue to blink, but a yellow indicator light will be
illuminated during this operation. Once the battery pack has reached
an appropriate temperature, the yellow light will turn off and the
charger will resume the charging procedure.
The charger will not charge a faulty battery pack. The charger will
indicate faulty battery pack by refusing to light.
NOTE: This could also mean a problem with a charger.
If the charger indicates a problem, take the charger and battery pack to
be tested at an authorised service centre.
HOT/COLD PACK DELAY
When the charger detects a battery pack that is too hot or too cold, it
automatically starts a Hot/Cold Pack Delay, suspending charging until
the battery pack has reached an appropriate temperature. The charger
then automatically switches to the pack charging mode. This feature
ensures maximum battery pack life.
A cold battery pack will charge at a slower rate than a warm battery
pack. The battery pack will charge at that slower rate throughout the
8
ENGLISH
entire charging cycle and will not return to maximum charge rate even if
the battery pack warms.
LITHIUM-ION BATTERY PACKS ONLY
XR Li-Ion tools are designed with an Electronic Protection System
that will protect the battery pack against overloading, overheating or
deep discharge.
The tool will automatically turn off if the Electronic Protection System
engages. If this occurs, place the lithium-ion battery pack on the
charger until it is fully charged.
Wall Mounting
These chargers are designed to be wall mountable or to sit upright on a
table or work surface. If wall mounting, locate the charger within reach
of an electrical outlet, and away from a corner or other obstructions
which may impede air flow. Use the back of the charger as a template
for the location of the mounting screws on the wall. Mount the charger
securely using drywall screws (purchased separately) at least 25.4 mm
long with a screw head diameter of 7–9 mm, screwed into wood to
an optimal depth leaving approximately 5.5 mm of the screw exposed.
Align the slots on the back of the charger with the exposed screws and
fully engage them in the slots.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using a
cloth or soft non-metallic brush. Do not use water or any
cleaning solutions. Never let any liquid get inside the tool;
never immerse any part of the tool into a liquid.
Important Safety Instructions for All Battery
Packs
When ordering replacement battery packs, be sure to include catalog
number and voltage.
The battery pack is not fully charged out of the carton. Before using
the battery pack and charger, read the safety instructions below. Then
follow charging procedures outlined.
9
E N GL I S H
READ ALL INSTRUCTIONS
• Do not charge or use battery in explosive atmospheres,
such as in the presence of flammable liquids, gases or dust.
Inserting or removing the battery from the charger may ignite the
dust or fumes.
• Never force battery pack into charger. Do not modify battery
pack in any way to fit into a non-compatible charger as
battery pack may rupture causing serious personal injury.
• Charge the battery packs only in DeWALT chargers.
• DO NOT splash or immerse in water or other liquids.
• Do not store or use the tool and battery pack in locations
where the temperature may reach or exceed 40 ˚C (104 ˚F)
(such as outside sheds or metal buildings in summer).
WARNING: Never attempt to open the battery pack for
any reason. If battery pack case is cracked or damaged,
do not insert into charger. Do not crush, drop or damage
battery pack. Do not use a battery pack or charger that
has received a sharp blow, been dropped, run over or
damaged in any way (i.e., pierced with a nail, hit with a
hammer, stepped on). Electric shock or electrocution may
result. Damaged battery packs should be returned to
service centre for recycling.
WARNING: Fire hazard. Do not store or carry the
battery pack so that metal objects can contact
exposed battery terminals. For example, do not place
the battery pack in aprons, pockets, tool boxes, product kit
boxes, drawers, etc., with loose nails, screws, keys, etc.
CAUTION: When not in use, place tool on its side on
a stable surface where it will not cause a tripping
or falling hazard. Some tools with large battery packs
will stand upright on the battery pack but may be easily
knocked over.
10
ENGLISH
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM-ION (LI-ION)
• Do not incinerate the battery pack even if it is severely
damaged or is completely worn out. The battery pack can
explode in a fire. Toxic fumes and materials are created when
lithium-ion battery packs are burned.
• If battery contents come into contact with the skin,
immediately wash area with mild soap and water. If
battery liquid gets into the eye, rinse water over the open eye for
15 minutes or until irritation ceases. If medical attention is needed,
the battery electrolyte is composed of a mixture of liquid organic
carbonates and lithium salts.
• Contents of opened battery cells may cause respiratory
irritation. Provide fresh air. If symptoms persists, seek
medical attention.
WARNING: Burn hazard. Battery liquid may be flammable
if exposed to spark or flame.
Transportation
WARNING: Fire hazard. Transporting batteries can
possibly cause fire if the battery terminals inadvertently
come in contact with conductive materials. When
transporting batteries, make sure that the battery terminals
are protected and well insulated from materials that could
contact them and cause a short circuit.
DeWALT batteries comply with all applicable shipping regulations
as prescribed by industry and legal standards which include UN
Recommendations on the Transport of Dangerous Goods; International
Air Transport Association (IATA) Dangerous Goods Regulations,
International Maritime Dangerous Goods (IMDG) Regulations, and
the European Agreement Concerning The International Carriage of
Dangerous Goods by Road (ADR). Lithium-ion cells and batteries
have been tested to section 38.3 of the UN Recommendations on the
Transport of Dangerous Goods Manual of Tests and Criteria.
In most instances, shipping a DeWALT battery pack will be excepted
from being classified as a fully regulated Class 9 Hazardous Material.
In general, only shipments containing a lithium-ion battery with an
11
E N GL I S H
energy rating greater than 100 Watt Hours (Wh) will require being
shipped as fully regulated Class 9. All lithium-ion batteries have the
Watt Hour rating marked on the pack. Furthermore, due to regulation
complexities, DeWALT does not recommend air shipping lithium-ion
battery packs alone regardless of Watt Hour rating. Shipments of tools
with batteries (combo kits) can be air shipped as excepted if the Watt
Hour rating of the battery pack is no greater than 100 Whr.
Regardless of whether a shipment is considered excepted or fully
regulated, it is the shipper’s responsibility to consult the latest
regulations for packaging, labeling/marking and documentation
requirements.
The information provided in this section of the manual is provided in
good faith and believed to be accurate at the time the document was
created. However, no warranty, expressed or implied, is given. It is
the buyer’s responsibility to ensure that its activities comply with the
applicable regulations.
TRANSPORTING THE FLEXVOLTTM BATTERY
The DeWALT FLEXVOLTTM battery has two modes: Use and Transport.
Use Mode: When the FLEXVOLTTM battery stands alone or is in a
DeWALT 18V product, it will operate as an 18V battery. When the
FLEXVOLTTM battery is in a 54V or a 108V (two 54V batteries) product,
it will operate as a 54V battery.
Transport Mode: When the cap is attached to the FLEXVOLTTM
battery, the battery is in Transport mode. Keep the cap for shipping.
When in Transport mode, strings of cells
are electrically disconnected within the
pack resulting in 3 batteries with a lower
Watt hour (Wh) rating as compared to 1
battery with a higher Watt hour rating. This increased quantity of 3
batteries with the lower Watt hour rating can exempt the pack from
certain shipping regulations that are imposed upon the higher Watt
hour batteries.
12
ENGLISH
For example, the Transport Wh rating Example of Use and Transport
might indicate 3 x 36 Wh, meaning 3 Label Marking
batteries of 36 Wh each. The Use
Wh rating might indicate 108 Wh
(1 battery implied).
Battery Pack
STORAGE RECOMMENDATIONS
1.The best storage place is one that is cool and dry away from
direct sunlight and excess heat or cold. For optimum battery
performance and life, store battery packs at room temperature
when not in use.
2.For long storage, it is recommended to store a fully charged
battery pack in a cool, dry place out of the charger for
optimal results.
NOTE: Battery packs should not be stored completely depleted of
charge. The battery pack will need to be recharged before use.
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual, the labels on the
charger and the battery pack may show the following pictographs:
Read instruction manual before use.
See Technical Data for charging time.
Battery charging.
Battery charged.
Battery defective.
13
E N GL I S H
Hot/cold pack delay.
Do not probe with conductive objects.
Do not charge damaged battery packs.
Do not expose to water.
Have defective cords replaced immediately.
Charge only between 4 ˚C and 40 ˚C.
Only for indoor use.
Discard the battery pack with due care for the environment.
Charge DeWALT battery packs only with designated
DeWALT chargers. Charging battery packs other than the
designated DeWALT batteries with a DeWALT charger may
make them burst or lead to other dangerous situations.
Do not incinerate the battery pack.
USE (without transport cap). Example: Wh rating indicates
108 Wh (1 battery with 108 Wh).
TRANSPORT (with built-in transport cap). Example: Wh
rating indicates 3 x 36 Wh (3 batteries of 36 Wh).
14
ENGLISH
Package Contents
The package contains:
1 Battery charger
1 Instruction manual
NOTE: Battery packs and chargers are not included with N-models.
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual prior
to operation.
DATE CODE POSITION (FIG. 1)
The date code (A), which also includes the year of manufacture, is
printed into the underside of the housing.
Example:
2016 XX XX
Year of Manufacture
INTENDED USE
The DCB132 charger is designed for charging 10,8V, 14,4V, 18V Li-Ion
XR and XR FLEXVOLT battery packs (DCB123, DCB125, DCB127,
DCB141, DCB142, DCB143, DCB144, DCB145, DCB181, DCB182,
DCB183, DCB183B, DCB184, DCB184B, DCB185, DCB546, DCB547).
DO NOT use under wet conditions or in presence of flammable liquids
or gases.
These battery chargers and battery packs are professional tools.
DO NOT let children come into contact with the charger. Supervision is
required when inexperienced operators use this charger.
• Only use rechargeable batteries with this charger.
BATTERY TYPE
DCB123
VOLTAGE
10,8
CELL
3 x Li-Ion
CAPACITY
1,5 Ah
DCB125
10,8
3 x Li-Ion
1,3 Ah
DCB127
10,8
3 x Li-Ion
2,0 Ah
DCB141
14,4
4 x Li-Ion
1,5 Ah
15
E N GL I S H
BATTERY TYPE
DCB142
VOLTAGE
14,4
CELL
8 x Li-Ion
CAPACITY
4,0 Ah
DCB143
14,4
4 x Li-Ion
2,0 Ah
DCB144
14,4
8 x Li-Ion
5,0 Ah
DCB145
14,4
4 x Li-Ion
1,3 Ah
DCB181
18
5 x Li-Ion
1.5 Ah
DCB182
18
10 x Li-Ion
4.0 Ah
DCB183
18
5 x Li-Ion
2.0 Ah
DCB184
18
10 x Li-Ion
5.0 Ah
DCB185
18
5 x Li-Ion
1.3 Ah
DCB546
18/54
15 x Li-Ion
6.0 Ah/2.0 Ah
DCB547
18/54
15 x Li-Ion
9.0 Ah/3.0 Ah
Electrical Safety
Always check that the battery pack voltage corresponds to the voltage
on the rating plate. Also make sure that the voltage of your charger
corresponds to that of your mains.
Your DeWALT charger is double insulated in accordance with
EN60335; therefore no earth wire is required.
If the supply cord is damaged, it must be replaced by a specially
prepared cord available through the DeWALT service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.
16
ENGLISH
WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 3 A.
Using an Extension Cable
An extension cord should not be used unless absolutely necessary.
Use an approved extension cable suitable for the power input of your
charger (see Technical Data). The minimum conductor size is 1 mm2;
the maximum length is 30 m.
When using a cable reel, always unwind the cable completely.
MAINTENANCE
Your DeWALT power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger is not serviceable. There are no serviceable parts inside
the charger.
• Do not attempt to repair the charger. To assure product safety
and reliability, repairs, maintenance, and adjustments should be
performed by authorized DeWALT service centers.
Lubrication
Your power tool requires no additional lubrication.
17
E N GL I S H
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories
WARNING: Since accessories, other than those offered
by DeWALT, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only DeWALT, recommended
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
eparate collection. Products and batteries marked with
S
this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries according to
local provisions. Further information is available at www.2helpU.com.
18
ENGLISH
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails to produce
sufficient power on jobs which were easily done before. At the end of
its technical life, discard it with due care for our environment:
• Run the battery pack down completely, then remove it from
the tool.
• Li-Ion cells are recyclable. Take them to your dealer or a local
recycling station. The collected battery packs will be recycled or
disposed of properly.
DeWALT, Richard-Klinger-Straße 11,
D-65510, Idstein, Germany
19
Belgique et
Luxembourg België
en Luxemburg
DeWALT - Belgium BVBA
Egide Walschaertsstraat 16
2800 Mechelen
Tel: NL 32 15 47 37 63
Tel: FR 32 15 47 37 64
Fax:
32 15 47 37 99
www.dewalt.be
enduser.BE@SBDinc.com
Danmark
DeWALT (Stanley Black&Decker AS)
Roskildevej 22
2620 Albertslund
DeWALT
Richard Klinger Str. 11
65510 Idstein
DeWALT (Ελλάς) Α.Ε.
EΔΡΑ-ΓΡΑΦΕΙΑ : Στράβωνος 7
& Λ. Βουλιαγμένης, Γλυφάδα 166 74, Αθήνα
SERVICE : Ημερος Τόπος 2 (Χάνι Αδάμ) – 193 00
Ασπρόπυργος
DeWALT Ibérica, S.C.A.
Parc de Negocios “Mas Blau”
Edificio Muntadas, c/Bergadá, 1, Of. A6
08820 El Prat de Llobregat (Barcelona)
DeWALT
5, allée des Hêtres
BP 60105, 69579 Limonest Cedex
DeWALT
In der Luberzen 42
8902 Urdorf
Tel:
Fax:
www.dewalt.dk
kundeservice.dk@sbdinc.com
Ireland
DeWALT
Building 4500, Kinsale Road
Cork Airport Business Park
Cork, Ireland
Tel:00353-2781800 www.dewalt.ie
Fax:
01278 1811
Sales.ireland@sbdinc.com
Italia
DeWALT
via Energypark 6
20871 Vimercate (MB), IT
Tel: Fax: 800-014353
www.dewalt.it
39 039-9590200
39 039-9590311
Nederlands
DeWALT
Netherlands BVPostbus 83,
6120 AB BORN
Tel:
Fax:
31 164 283 063 www.dewalt.nl
31 164 283 200
Norge
DeWALT
Postboks 4613
0405 Oslo, Norge
Tel: Fax: 45 25 13 00
45 25 08 00
Österreich
DeWALT
Werkzeug Vertriebsges m.b.H
Oberlaaerstrasse 248, A-1230 Wien
Tel: Fax: 01 - 66116 - 0
www.dewalt.at
01 - 66116 - 614 service.austria@sbdinc.com
Portuga
DeWALT
Tel: Ed. D Dinis, Quina da Fonte
Fax: Rua dos Malhoes 2 2A 2º Esq.
Oeiras e S. Juliao da Barra, paço de Arcos e Caxias
2770 071 Paço de Arcos
+351 214667500 www.dewalt.pt
+351214667580 resposta.posvenda@
sbdinc.com
Suomi
DeWALT
PL47
00521 Helsinki, Suomi
Puh: Faksi:
010 400 4333
0800 411 340
www.dewalt.fi
asiakaspalvelu.fi@sbdinc.com
Sverige
DeWALT
BOX 94
43122 Mölndal
Sverige
Tel:
Fax: 031 68 61 60
031 68 60 08
www.dewalt.se
kundservice.se@sbdinc.com
Türkiye
KALE Hırdavat ve Makina A.Ş.
Defterdar Mah. Savaklar Cad. No:15
Edirnekapı / Eyüp / İSTANBUL 34050 TÜRKİYE
DeWALT, 210 Bath Road;
Slough, Berks SL1 3YD
Tel: Faks:
0212 533 52 55 www.dewalt.com.tr
0212 533 10 05
Tel: Fax: 01753-567055
01753-572112
DeWALT
810 Whitehorse Road Box Hill
VIC 3103 Australia
DeWALT
P.O. Box - 17164,
Jebel Ali Free Zone (South), Dubai, UAE
Tel: Aust 1800 338 002
Tel: NZ 0800 339 258
Deutschland
Ελλάς
España
France
Schweiz
Suisse
Svizzera
United
Kingdom
Australia
Middle East Africa
70 20 15 10
70 22 49 10
Tel:06126-21-0
Fax:06126-21-2770
www.dewalt.de
infodwge@sbdinc.com
Τηλ:00302108981616 www.dewalt.gr
Φαξ:00302108983570 Greece.Service@sbdinc.com
Tel:
Fax:
934 797 400
934 797 419
www.dewalt.es
respuesta.postventa@
sbdinc.com
Tel:
Fax:
04 72 20 39 20
04 72 20 39 00
www.dewalt.fr
scufr@sbdinc.com
Tel:
Fax:
044 - 755 60 70 www.dewalt.ch
044 - 730 70 67 service@rofoag.ch
Tel: Fax: www.dewalt.no
kundeservice.no@sbdinc.com
www.dewalt.co.uk
emeaservice@sbdinc.com
www.dewalt.com.au
www.dewalt.co.nz
971 4 812 7400 www.dewalt.ae
971 4 2822765 Service.MEA@sbdinc.com
N48240309/16
Download PDF

advertising