FMC792 | Stanley FMC792 NAILER Type 2 instruction manual
(Original instructions)
14 13
(Original instructions)
Intended use
Your Stanley Fat Max FMC792B cordless nailer has been
de-signed for nailing. This appliance is intended for
professional and private, non professional users.
Safety instructions
General power tool safety warnings
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings
and instructions listed below may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
(Original instructions)
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Battery tool use and care
a. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
b. Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
c. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws, or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
d. Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Safety of others
Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
Hold power tool by insulated gripping surfaces when
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contacting
a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
Hold power tool by insulated gripping surfaces, when
performing an operation where the fastener may
contact hidden wiring. Fasteners contacting a "live" wire
may make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
Never allow children, persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge or people unfamiliar with these instructions to
use the machine,
local regulations may restrict the age of the operator.
Never operate the machine while people, especially
children, or pets are nearby.
Additional Safety Instructions for Cordless Nailers
Additional power tool safety warnings
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
Before drilling into walls, floors or ceilings, check for the
location of wiring and pipes.
Avoid touching the tip of a drill bit just after drilling, as it
may be hot.
The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recommended in this instruction manual may present a risk of
personal injury and/or damage to property.
Always wear safety glasses.
Always wear ear protection.
Only use fasteners of the type specified in the manual.
Do not use any stands for mounting the tool to a
Do not disassemble or block any parts of the fastener
driving tool such as the contact trip.
Prior to each operation check that the safety and
triggering mechanism is functioning properly and that
all nuts and bolts are tight.
Do not use the tool as a hammer.
Do not use the tool on a ladder.
Never point any operational fastener driving tool at
yourself or at any other person.
While working, hold the tool in such a way that no
injuries can be caused to the head or to the body in
the event of a possible recoil due to a disruption in
the energy supply or hard areas within the work piece.
Never actuate the fastener driving tool into free space.
In the work area, carry the tool at the workplace using
only one handle, and never with the trigger actuated.
Consider the conditions in the work area Fasteners
can penetrate thin work pieces or slip off corners and
edges of the work piece, and thus put people at risk.
Do not drive fasteners close to the edge of the work
Do not drive fasteners on top of other fasteners.
Always assume that the tool contains fasteners.
(Original instructions)
Careless handling of the nailer can result in unexpected firing of fasteners and personal injury.
Do not point the tool towards yourself or anyone
nearby. Unexpected triggering will discharge the fastener
causing injury.
Do not actuate the tool unless it is placed firmly
against the workpiece. If the tool is not in contact, the
fastener may be deflected away from your target.
Disconnect the tool from the power source when the
fastener jams in the tool. While removing a jammed
fastener, the nailer may be accidentally activated if it is
plugged in.
Do not use this tool for fastening electrical cables.
It is not designed for electric cable installation and may
damage the insulation of electric cables thereby causing
electric shock or fire hazards.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings.
These risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving parts.
u Injuries caused when changing any parts, blades or accessories.
u Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
u Impairment of hearing.
u Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured in
accordance with a standard test method provided by EN50636
and may be used for comparing one tool with another. The
declared vibration emission value may also be used in a
preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following symbols are shown on the tool along with the
date code:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Warning! To reduce the risk of injury, the
user must wear ear and eye protection.
Keep hands and body parts clear of
immediate work area.
Additional safety instructions for batteries and
u Never attempt to open for any reason.
u Do not expose the battery to water.
u Do not store in locations where the temperature may
exceed 40 °C.
u Charge only at ambient temperatures between 10 °C and
40 °C.
u When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
u Do not damage/deform the battery pack either by puncture
or impact, as this may create a risk of injury and fire.
u Do not charge damaged batteries.
u Under extreme conditions, battery leakage may occur.
When you notice liquid on the batteries Carefully wipe the
liquid off using a cloth. Avoid skin contact.
u In case of skin or eye contact, follow the instructions
Warning! The battery fluid may cause personal injury or
damage to property. In case of skin contact, immediately rinse
with water. If redness, pain or irritation occurs seek medical
attention. In case of eye contact, rinse immediately with clean
water and seek medical attention.
Do not attempt to charge damaged batteries
u Use your Stanley Fat Max charger only to charge the
battery in the tool with which it was supplied. Other
batteries could burst, causing personal injury and damage.
u Never attempt to charge non-rechargeable batteries.
u Have defective cords replaced immediately.
u Do not expose the charger to water.
u Do not open the charger.
u Do not probe the charger
(Original instructions)
Symbols on charger
The charger is intended for indoor use only.
Read the instruction manual before use.
The green LED will flash indicating that the battery is being
Electrical safety
Your adapter is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on the
rating plate. Never attempt to replace the adapter
unit with a regular mains plug.
This appliance includes some or all of the following features.
1. Trigger Switch
2. Trigger Lock-Off switch
3. Depth adjustment wheel
4. Depth adjustment indicator
5. Worklights/low battery/jam/stall indicator
6. Stall release lever
7. Jam clearing latch
8. Contact trip
9. Magazine
10. Pusher latch
11. Belt hook
12. Pusher latch release
The completion of charge is indicated by the green LED
remaining on continuously. The pack is fully charged and
may be used at this time or left in the charger
Warning! Recharge discharged batteries as soon as possible after use or battery life may be greatly diminished.
Charger diagnostics
This charger is designed to detect certain problems that can
arise with the battery packs or the power source. Problems
are indicated by one LED flashing in different patterns.
Bad Battery
The charger can detect a weak or damaged battery. The
red LED flashes in the pattern indicated on the label. If you
see this bad battery blink pattern, do not continue to charge
the battery. Return it to a service centre or a collection site
for recycling
Hot/Cold Pack Delay
Charging the battery
The battery needs to be charged before first use and
whenever it fails to produce sufficient power on jobs that were
easily done before.
The battery may become warm while charging; this is normal
and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging temperature: approx. 24 °C.
Note: The charger will not charge a battery if the cell temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell temperature
warms up or cools down.
u Plug the charger into an appropriate outlet before inserting
the battery pack.
u Insert the battery pack into the charger.
When the charger detects a battery that is excessively
hot or excessively cold, it automatically starts a Hot/Cold
Pack delay, suspending charging until the battery has
normalised. After this happens, the charger automatically
switches to the Pack Charging mode. This feature ensures
maximum battery life. The red LED flashes in the pattern
indicated on the label when the Hot/Cold pack delay is
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery
pack fresh and fully charged.
Important charging notes
(Original instructions)
Longest life and best performance can be obtained if
the battery pack is charged when the air temperature is
between 18°- 24°C. DO NOT charge the battery pack in
an air temperature below +4.5°C, or above +40.5°C. This
is important and will prevent serious damage to the battery
pack .
u The charger and battery pack may become warm to touch
while charging. This is a normal condition, and does not
indicate a problem. To facilitate the cooling of the battery
pack after use, avoid placing the charger or battery pack
in a warm environment such as in a metal shed, or an
uninsulated trailer
u If the battery pack does not charge properly:
u Check current at receptacle by plugging in a lamp or
other appliance
u Check to see if receptacle is connected to a light switch
which turns power off when you turn out the lights.
u Move charger and battery pack to a location where the
surrounding air temperature is approximately 18°24°C.
u If charging problems persist, take the appliance, battery
pack and charger to your local service center.
u The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily done
previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with no
adverse affect on the battery pack.
u Foreign materials of a conductive nature such as, but
not limited to, steel wool, aluminium foil, or any buildup
of metallic particles should be kept away from charger
cavities. Always unplug the charger from the power supply
when there is no battery pack in the cavity. Unplug charger
before attempting to clean.
u Do not freeze or immerse charger in water or any other
Warning! Shock hazard. Do not allow any liquid to get inside
charger. Never attempt to open the battery pack for any
If the plastic housing of the battery pack breaks or cracks,
return to a service center for recycling.
Installing and removing the battery pack from the
Warning! Make certain the lock-off button is not engaged to
prevent switch actuation before removing or installing battery.
To install battery pack
Insert battery (A1) into appliance until an audible click is
heard (Figure A). Ensure battery pack is fully seated and fully
latched into position.
To remove battery pack
Depress the battery release button (B1) as shown in Figure B
and pull battery pack out of appliance.
Warning! Read the section titled Nailer Safety Warnings at
the beginning of this manual. Always wear eye and ear protection when operating this tool.
Keep the nailer pointed away from yourself and others. For
safe operation, complete the following procedures and checks
before each use of the nailer.
Warning! To reduce the risk of personal injury, disconnect
battery pack from tool and engage trigger lock-off before
performing maintenance, clearing a jammed nails, leaving
work area, moving tool to another location or handing the tool
to another person.
Warning! Keep fingers AWAY from trigger when not driving
fasteners to avoid accidental firing. Never carry tool with finger
on trigger.
u Wear proper eye, hearing and respiratory protection.
u Remove battery pack from tool and engage trigger lockoff.
u Lock the pusher in the back position and remove all nail
strips from the magazine.
u Check for smooth and proper operation of contact trip and
pusher assemblies. Do not use tool if either assembly is
not functioning properly.
u Never use a tool that has damaged parts.
To operate the nailer
Warning! The contact trip needs to be depressed followed by
a full trigger pull for each nail followed by a release of both the
contact trip and trigger after each nail.
Warning!The battery should always be removed and the
trigger lock-off engaged whenever any adjustments are made
or when tool is not in use.
u Fully depress contact trip against the work surface.
u Fully pull trigger and motor will start. (nail will drive into
work surface).
u Release trigger.
u Lift contact trip off work surface.
u Repeat the above 4 steps for next application
Preparing the tool
Warning! NEVER spray or in any other way apply oil, lubricants or cleaning solvents inside the tool. This can seriously
affect the life and performance of the tool.
Warning! The battery should always be removed and the
trigger lock-off engaged whenever any adjustments are made
or when tool is not in use.
u Read the Safety Instruction section of this manual.
(Original instructions)
Wear eye and ear protection.
Remove battery from tool and fully charge.
Ensure magazine is empty of all fasteners.
Check for smooth and proper operation of contact trip and
pusher assemblies. Do not use tool if either assembly is
not functioning properly.
Keep tool pointed away from yourself and others.
Insert fully charged battery pack.
Work lights (Fig. F)
There are work lights (5) located on each side of the nailer.
Work lights turn on upon depressing the contact trip.
Note: These work lights are for illuminating the immediate
work surface and are not intended to be used as flashlights.
Loading the Tool
Warning! Keep the tool pointed away from yourself and others. Serious personal injury may result.
Warning! Never load nails with the contact trip or trigger
Warning! Always remove battery pack before loading or
unloading nails.
Warning! The battery should always be removed and the trigger lock-off is engaged whenever any adjustments are made
or when tool is not in use.
Warning! Keep fingers clear of pusher to prevent injury.
u Insert fasteners into the bottom of the magazine (9).
u Pull pusher (10) downward until the nail follower
(C1) falls behind the nails as shown in figure C.
u Release the pusher (10).
Unloading the Tool
Warning!The battery should always be removed and the
trigger lock-off engaged whenever any adjustments are made
or when tool is not in use.
u Press pusher latch release button (12).
u Manually slide nails towards the bottom of the magazine
u Open the jam clear door (7) on the nosepiece to verify
there are no nails remaining.
Adjusting Depth (Fig. D, E)
The depth that the fastener is driven can be adjusted using
the depth adjustment wheel (3) on the side of the tool.
Warning!To reduce risk of serious injury from accidental
actuation when attempting to adjust depth, Always:
u Remove battery pack.
u Engage trigger lock-off.
u Avoid contact with trigger during adjustments.
Depth settings are on a sliding scale (4). The left side indicating the deepest and the right side indicating the shallowest.
u To drive a nail deeper, rotate the depth adjustment wheel
(3) downwards. This will slide the depth adjustment indicator (4) to the left on the scale.
u To drive a nail shallower, rotate the depth adjustment
wheel (3) upwards. This will slide the depth adjustment
indicator (4) to the right on the scale.
Low Battery Indicator:
The work lights will flash and then turn off completely to
indicate low battery.
Jammed Nail Indicator:
The work lights will flash continually if a nail becomes jammed
in the nose piece (see Clearing a jammed nail).
Stall Release (Fig. G)
Warning!If a stall occurs, the tool will disable itself and will require you to reset it. To do so, follow instructions on clearing a
stalled condition. Next remove battery pack and then reinsert
battery pack. The tool will now be operational. If the nailer is
used in a rigorous application where all available energy in the
motor is used to drive a fastener, the tool may stall. The driver
blade did not complete the drive cycle and the jam/stall indicator will flash. Rotate the stall release lever (6) on the tool and
the mechanism will release as shown in figure G.
Note! The tool will disable itself and not reset until the battery
pack has been removed and reinserted. If the unit continues
to stall please review the material and fastener length to be
sure that it is not too rigorous an application. If the driver
blade does not automatically return to the home position after
rotating the stall release lever, proceed to “clearing a jammed
Clearing a Jammed Nail (Fig. H)
Warning!To reduce the risk of personal injury, disconnect
battery pack from tool and engage trigger lock-off before
performing maintenance, or clearing a jammed nail.
If a nail becomes jammed in the nosepiece, keep the tool
pointed away from you and follow these instructions to clear:
u Remove battery pack from tool and engage trigger lockoff.
(Original instructions)
Rotate the stall release lever (6) on the tool to release the
driver blade and clear the jam. If tool is still jammed follow
the 9 steps listed below:
u Pull pusher downward until it locks in place then tip the
tool over so the nails slide freely out from the bottom of
the magazine.
Lift the jam clearing latch (7) then pull up to open front
door (14).
u Remove bent nail, using pliers if necessary.
u If driver blade is in the down position, insert screwdriver
or other rod into nosepiece and push driver blade back
in position.
u Close the front door and engage the wire form (13)
under the two arms (15) on the contact trip. Push jam
clearing latch down (7) until it locks in place.
u Reinsert nails into magazine (see Loading the Tool).
u Pull pusher (10) downward until the nail follower (C1)
falls behind the nails as shown in figure C.
u Reinsert battery pack.
u Disengage trigger lock-off (2), allowing the trigger to be
Warning!If a jam occurs, the tool will disable itself and will
require you to reset it. To do so, follow instructions on clearing
the jammed nail. Next remove battery pack and then reinsert
battery pack. The tool will now be operational.
Note!Should nails continue to jam frequently in contact trip,
have tool serviced by an authorized Stanley Fat Max service
Cold Weather Operation
When operating tools at temperatures below freezing:
u Keep tool as warm as possible prior to use.
u Actuate the tool 5 or 6 times into scrap lumber before
Hot Weather Operation
Tool should operate normally. However, keep tool out of direct
sunlight as excessive heat can deteriorate bumpers and other
rubber parts resulting in increased maintenance.
Belt Hook (Fig. I-J)
Warning!Remove nails from magazine before making any
adjustments or servicing this tool. Failure to do so may result
in serious injury.
Remove battery pack from tool, and engage trigger lockoff.
With a screwdriver remove screw from hang hook cavity
on the base of the tool (16).
Place the front lip of the hang hook (11) into the cavity on
the base of the tool (16) as shown in Figure I.
Secure the hang hook (11) with the supplied screw (17)
and firmly tighten with a screwdriver as shown in Figure J.
Replace battery pack.
Replacement parts
Warning!To reduce the risk of personal injury, disconnect
battery pack from tool and engage trigger lock-off before
performing maintenance, or clearing a jammed nail.
The tool comes equipped with a spare no mar tip located on
the side of the nail magazine.
u To replace the no mar pad, simply pull off the old no mar
pad and refit the new no mar pad onto the contact trip.
Use only identical replacement parts. For a parts list or to
order parts, visit our service website at
uk. You can also order parts from your nearest
Stanley Fat Max Factory Service Center or Stanley Fat Max
Authorized Warranty.
If your appliance seems not to operate properly, follow the
following instructions.
If this does not solve the problem, please contact your local
Stanley Fat Max repair agent.
Warning! Before proceeding, unplug the appliance.
Possible Cause
Possible Solution
Unit will not start.
Battery pack not
installed properly.
Check battery pack
Battery pack not
Check battery pack charging
Trigger lock-off is
Disengage trigger lock-off.
Tool doesn’t
(Headlights on,
motor does not
Motor stops running
after 2 seconds.
Normal operation; release
trigger or contact trip and
Tool doesn’t
Low battery charge or
damaged battery.
Charge or replace battery.
Tool doesn’t
(Headlights flash
Jammed fastener / tool
Remove the battery, rotate the
stall release lever. Clear the
jammed fastener, and reinsert
battery pack.
Jammed mechanism
See authorized service center.
Tool doesn’t
((Headlights on,
motor runs,
driver blade
stuck down)
See authorized service center.
(Original instructions)
Possible Cause
Possible Solution
Tool operates,
but does
not drive the
fastener fully.
Low battery charge or
damaged battery.
Charge or replace battery.
Depth adjustment set
too shallow.
Rotate depth adjustment
wheel to
a deeper setting.
Read instruction manual.
Material and fastener
length too rigorous an
Choose appropriate material
or fastener length.
Your Stanley Fat Max corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends
upon proper tool/appliance care and regular cleaning.
Warning! Switch off and unplug the appliance before carrying
out any cleaning.
u Dirt and grease may be removed from the exterior of the
appliance using a cloth.
Warning! NEVER use solvents or other harsh chemicals
for cleaning the non-metallic parts of the appliance. These
chemicals may weaken the materials used in these parts. Use
a cloth dampened only with water and mild soap. Never let
any liquid get inside the unit; never immerse any part of the
unit into a liquid.
Warning! NEVER spray or in any other way apply lubricants
or cleaning solvents inside the tool. This can seriously affect
the life and performance of the tool.
Service Notes
This product is not user serviceable. There are no user
serviceable parts inside the nailer. Servicing at an authorized
service center is required to avoid damage to static sensitive
internal components.
Protecting the environment
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
FMC792B Type:2
Tool not firmly applied
to workpiece.
Technical data
Barttery Type
Actuating mode
Magazine angle
No load speed
Drive energy
Weight (bare tool)
25 - 64
Shank diameter
Input voltage
Output voltage
1 hr (2.0 Ah)
2 hr (4.0 Ah)
Approx. charge time
Weight (bare
Level of sound pressure according to EN 60745 - 1:
Sound pressure (LpA) 87 dB(A), uncertainty (K) 1.5 dB(A)
Sound power (LWA) 92 dB(A), uncertainty (K) 2.5 dB(A)
Vibration total values (triax vector sum) according to EN 60745 - 2 - 16:
Staple nails (ah) 1.8 m/s2, uncertainty (K) 1.8 m/s2
(Original instructions)
EC declaration of conformity
FMC792B - Cordless Nailer
Stanley Fat Max declares that these products described under
"technical data" are in compliance with:
EN60745-1: 2009 +A11:2010,
EN 60745 - 2 -16:2010
These products also comply with Directive 2004/108/EC (until
19/04/2016) 2014/30/EU (from 20/04/2016), 2006/42/EC and
For more information, please contact Stanley Fat Max at the
following address or refer to the back of the manual.
The undersigned is responsible for compilation of the
technical file and makes this declaration on behalf of
Stanley Fat Max.
Stanley Fat Max is confident of the quality of its products and
offers consumers a 12 month guarantee from the date
of purchase. This guarantee is in addition to and in no way
prejudices your statutory rights. The guarantee is valid within
the territories of the Member States of the European Union
and the European Free Trade Area.
To claim on the guarantee, the claim must be in accordance
with Stanley Fat Max Terms and Conditions and you will need
to submit proof of purchase to the seller or an authorised
repair agent. Terms and conditions of the Stanley Fat Max 1
year guarantee and the location of your nearest authorised
repair agent can be obtained on the Internet at www.2helpU.
com, or by contacting your local Stanley Fat Max office.
Please visit our website to register
your new Stanley Fat Max product and receive updates on
new products and special offers.
R. Laverick
Director of Engineering
Stanley Fat Max,
210 Bath Road, Slough,
Berkshire, SL1 3YD
United Kingdom
United Kingdom
Stanley Fat Max
210 Bath Road
Slough, Berkshire SL1 3YD
90635344 REV-01
Tel. 01753 511234
Fax 01753 572112
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF