BDCROS18 | Black&Decker BDCROS18 RANDOM ORBITAL SANDER instruction manual

2
1
5
4
3
www.blackanddecker.co.uk
BDCROS18
4
6a
6
B
A
7
4
4
C
D
3
2
8
E
2
F
5
G
9
10
H
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
5
I
Intended use
Your BLACK+DECKER BDCROS18 random orbital sander has
been designed for sanding wood, metal, plastics and painted
surfaces. This tool is intended for consumer use only.
Safety instructions
General power tool safety warnings
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery operated (cordless) power tool.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the charger. Keep cord
away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric
shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3
ENGLISH
(Original instructions)
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication.
A moment of inattention while operating power tools may
result in serious personal injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
4
e. Maintain power tools.
Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may
affect the power tools operation. If damaged, have the
power tool repaired before use. Many accidents are
caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Battery tool use and care
a. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
b. Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
c. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws, or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
d. Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6.Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional power tool safety warnings
Warning! Additional safety warnings for sanders
u
Hold power tool by insulated gripping surfaces when
performing an operation where the sanding accessory
may contact hidden wiring. Sanding accessory contacting a "live" wire may make exposed metal parts of the
power tool "live" and could give the operator an electric
shock
(Original instructions)
u
Use clamps or another practical way to secure and
support the workpiece to a stable platform.
Holding the work by hand or against your body leaves it
unstable and may lead to loss of control.
Warning! Contact with or inhalation of dusts
arising from sanding applications may endanger
the health of the operator and possible bystanders. Wear a dust mask specifically designed for
protection against dust and fumes and ensure
that persons within or entering the work area are
also protected.
Thoroughly remove all dust after sanding.
Take special care when sanding paint which is possibly
lead based or when sanding some woods and metal which
may produce toxic dust:
u Do not let children or pregnant women enter the work
area.
u Do not eat, drink or smoke in the work area.
u Dispose of dust particles and any other debris safely.
u The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recommended in this instruction manual may present a risk of
personal injury and/or damage to property.
u
u
Safety of others
Never allow children, persons with reduced physical, sensory
or mental capabilities or lack of experience and knowledge or
people unfamiliar with these instructions to use the machine,
local regulations may restrict the age of the operator.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving parts.
u Injuries caused when changing any parts, blades or accessories.
u Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
ENGLISH
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured in
accordance with a standard test method provided by EN60745
and may be used for comparing one tool with another. The
declared vibration emission value may also be used in a
preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following pictograms are shown on the tool along with the
date code:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Additional safety instructions for batteries and
chargers
Batteries
Never attempt to open for any reason.
Do not expose the battery to water.
u Do not store in locations where the temperature may
exceed 40 °C.
u Charge only at ambient temperatures between 10 °C and
40 °C.
u Charge only using the charger provided with the tool.
u When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
u
u
Chargers
Use your BLACK+DECKER charger only to charge the
battery in the tool with which it was supplied. Other batteries could burst, causing personal injury and damage.
u Never attempt to charge non-rechargeable batteries.
u Have defective cords replaced immediately.
u Do not expose the charger to water.
u Do not open the charger.
u
$
u
Do not probe the charger.
The charger is intended for indoor use only.
Read the instruction manual before use.
5
ENGLISH
(Original instructions)
Electrical safety
#
u
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on the
rating plate. Never attempt to replace the charger
unit with a regular mains plug.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Centre
in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1.Handle
2. On/off button
3. Sanding pad
4.Battery
5. Dust canister
6. Charger
Charging procedure (Fig. A)
BLACK+DECKER chargers are designed to charge
BLACK+DECKER battery packs.
u Plug the charger (6) into an appropriate outlet before
inserting the battery pack (4).
u Insert the battery pack (4) into the charger (6) as shown in
figure A.
u The green LED (6a) will flash indicating that the battery is
being charged.
u The completion of charge is indicated by the green LED
(6a) remaining on continuously. The pack is fully charged
and may be used at this time or left on the charger.
Note: Recharge discharged batteries as soon as possible
after use or battery life may be greatly diminished. For longest
battery life, do not discharge batteries fully.
It is recommended that the batteries be recharged after each
use.
Leaving the battery in the charger
The charger (6) and battery pack (4) can be left connected
with the LED glowing indefinitely. The charger will keep the
battery pack fresh and fully charged.
Important charging notes
Longest life and best performance can be obtained if
the battery pack is charged when the air temperature is
between 65°F and 75°F (18°- 24°C). DO NOT charge the
battery pack in an air temperature below +40°F (+4.5°C),
or above +105°F (+40.5°C). This is important and will
prevent serious damage to the battery pack.
u The charger and battery pack may become warm to touch
while charging. This is a normal condition, and does not
u
6
indicate a problem. To facilitate the cooling of the battery
pack after use, avoid placing the charger or battery pack
in a warm environment such as in a metal shed, or an
uninsulated trailer.
u If the battery pack does not charge properly:
u Check current at receptacle by plugging in a lamp or
other appliance.
u Check to see if receptacle is connected to a light switch
which turns power off when you turn out the lights.
u Move charger and battery pack to a location where the
surrounding air temperature is approximately 65°F
- 75°F (18°- 24°C).
u If charging problems persist, take the tool, battery pack
and charger to your local service center.
u The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily done
previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with no
adverse affect on the battery pack.
u Foreign materials of a conductive nature such as, but
not limited to, steel wool, aluminium foil, or any buildup
of metallic particles should be kept away from charger
cavities. Always unplug the charger from the power supply
when there is no battery pack in the cavity. Unplug charger
before attempting to clean.
u Do not freeze or immerse charger in water or any other
liquid.
Warning! Do not allow any liquid to get inside charger. Never
attempt to open the battery pack for any reason. If the plastic
housing of the battery pack breaks or cracks, return to a
service center for recycling.
Charger Diagnostics (Fig.B)
Refer to the indicators in figure B for the charge status of the
battery pack.
Bad Battery
If you see a bad battery blink pattern, do not continue
to charge this battery. Return it to a service center or a
collection site for recycling.
Hot/Cold Pack Delay
When the charger detects a battery pack that is too hot
or too cold, it automatically starts a Hot/Cold Pack Delay,
suspending charging until the battery pack has reached an
appropriate temperature. The charger then automatically
switches to the pack charging mode. This feature ensures
maximum battery pack life. A cold battery pack will charge at a
slower rate than a warm battery pack. The pack will charge at
that slower rate throughout the entire charging cycle and will
not return to maximum charge rate even if the pack warms.
(Original instructions)
Installing and removing the battery pack from the
tool
u
u
To install battery pack Fig. C)
u Insert battery (4) into tool until an audible click is heard
(Figure. C)
u Ensure battery pack is fully seated and fully latched into
position.
To remove battery pack (Fig.D)
u Depress the battery release button (7) as shown in figure
D and pull battery pack (4) out of the tool.
Attaching hook and loop sanding discs (fig.E)
For best results, use BLACK+DECKER accessories.
u Your sander is designed for use with either mesh carbide
sandpaper or with standard sand paper with the 8 hole
dust extraction pattern.
u To attach the sanding disc (8), carefully center it over the
sanding pad (3) ensuring the holes in the disc align with
the holes in the pad and press the disc firmly in place.
u The hook and loop fastening system sanding disc can be
easily removed by simply pulling it off. It can be reused as
desired.
Use
Warning! Let the tool work at its own pace. Do not overload.
Switching on and off
u To switch the tool on, depress the on/off switch (2) at the
u
"I" position.
To switch the tool off, depress the on/off switch (2) at
the"O" position.
Operation
Grasp the sander as shown in figure G and turn it ON. Move it
in long, sweeping strokes along the surface, letting it do
the work.
Pushing down on the tool while sanding actually slows the
removal rate and produces an inferior quality finish.
Check your work often. Sander is capable of removing
material rapidly especially with coarse paper.
Dust Collection (Fig. H, I)
Warning! Collected sanding dust from sanding surface coatings (polyurethane, linseed oil, etc.) can selfignite in sander
dust bag or elsewhere and cause fire. To reduce risk, empty
bag frequently and strictly follow sander manual and coating
manufacturer’s instructions.
u To attach the canister to the sander, line up the grooves in
the canister (9) with the nubs (10) on the dust port.
u Slide the canister onto the dust port and turn the canister
clockwise to lock it in place as shown in Figure H.
ENGLISH
To remove, turn the canister counterclockwise and slide
the canister off.
To empty the canister, remove it from the dust port and
dump the sanding debris into an appropriate trash receptacle Figure I.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance, switch off and
unplug the tool.
u Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
u Safely dispose of the old plug.
u Connect the brown lead to the live terminal in the new
plug.
u Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste
Products and batteries contain materials that can be recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to local provisions. Further information is available at
www.2helpU.com
Technical data
BDCROS18 H1
Input voltage
Vdc
Oscillations (no load)
min-1
12000
Orbits (no load)
min-1
12000
Sanding base surface
mm
12660
Weight
kg
Battery
18
2
0.9
BL1518
Voltage
VDC
18
Capacity
Ah
1.5
Type
H4
7
(Original instructions)
ENGLISH
BDCROS18 H1
Charger
SSC-250040X
Input voltage
VAC
230
Output voltage
VDC
8 - 20
Current
mA
400
The undersigned is responsible for compilation of the
technical file and makes this declaration on behalf of
Black & Decker.
Ray Laverick
Director of Engineering
Black & Decker Europe, 210 Bath Road, Slough,
Berkshire, SL1 3YD
United Kingdom
09/03/2015
LpA (sound pressure) 71.5 dB(A), Uncertainty (K) 3 dB(A)
LWA (sound power) 82.5 dB(A), Uncertainty (K) 3 dB(A)
Vibration total values (triax vector sum) according to EN 60745:
Vibration emission value (ah) 3.4 m/s2, uncertainty (K) 1.5 m/s2
EC declaration of conformity
%
MACHINERY DIRECTIVE
BDCROS18 Random orbital sander
Black & Decker declares that these products described under
"technical data" are in compliance with:
2006/42/EC, EN 60745-1:2009 +A11:2010,
EN 60745-2-4:2009 + A11:2011
These products also comply with Directive
2014/30/EU and 2011/65/EU.
For more information, please contact Stanley Europe at the
following address or refer to the back of the manual.
Guarantee
Black & Decker is confident of the quality of its products and
offers consumers a 24 month guarantee from the date
of purchase. This guarantee is in addition to and in no way
prejudices your statutory rights. The guarantee is valid within
the territories of the Member States of the European Union
and the European Free Trade Area.
To claim on the guarantee, the claim must be in accordance
with Black & Decker Terms and Conditions and you will need
to submit proof of purchase to the seller or an authorised repair agent. Terms and conditions of the Black&Decker 2 year
guarantee and the location of your nearest authorised repair
agent can be obtained on the Internet at www.2helpU.com, or
by contacting your local Black & Decker office at the address
indicated in this manual.
Please visit our website www.blackanddecker.co.uk to register
your new Black & Decker product and receive updates on new
products and special offers.
Australia
New Zealand
Black & Decker (Australia) Pty. Ltd.
20 Fletcher Road, Mooroolbark,
Victoria, 3138
Tel. Fax 03-8720 5100
03-9727 5940
Black & Decker
5 Te Apunga Place
Mt Wellington
Aukland 1060
Tel. Fax +64 9 259 1133
+64 9 259 1122
United Kingdom &
Republic Of Ireland
www.blackanddecker.co.uk emeaservice@sbdinc.com
Black & Decker
210 Bath Road
Slough, Berkshire SL1 3YD
Tel. Fax N498241 REV-0
8
01753 511234
01753 512365
04/2017
Download PDF

advertising