DCN890 | DeWalt DCN890 NAILER instruction manual

DCN890
Final page size: A5 (148mm x 210mm)
English (original instructions)4
Copyright DeWALT
B
Fig. A
8
7
5
6
2
15
1
4
3
9
12
11
13
16
10
14
Fig. B
11
10
11
10
22
1
Fig. C
Fig. D
16
17
Fig. E
Fig. F
2
Fig. G
Fig. H
4
3
Fig. I
2
8
Fig. J
15
Fig. K
Fig. L
5
7
19
18
6
Fig. M
Fig. N
22
21
20
3
English
CORDLESS CONCRETE NAILER
DCN890
Congratulations!
EC-Declaration of Conformity
You have chosen a DeWALT tool. Years of experience, thorough
product development and innovation make DeWALT one of the
most reliable partners for professional power tool users.
Machinery Directive
Technical Data
Voltage
Type
Battery type
Magazine angle
Loading capacity
Length of Pins
Pin Thickness
Weight (without battery pack)
VDC
mm
mm
kg
DCN890
18
1
Li-Ion
15
up to 33 pins
13–57
2.6–3.7
4.2
Noise values and vibration values (triax vector sum) according to EN60745-2-16
LPA(emission sound pressure level)
dB(A)
88.5
LWA(sound power level)
dB(A)
97.5
K (uncertainty for the given sound level)
dB(A)
3.5
Vibration emission value ah =
Uncertainty K =
m/s2
m/s2
2.8
1.5
The vibration emission level given in this information sheet has
been measured in accordance with a standardised test given in
EN60745 and may be used to compare one tool with another. It
may be used for a preliminary assessment of exposure.
WARNING: The declared vibration emission level
represents the main applications of the tool. However if
the tool is used for different applications, with different
accessories or poorly maintained, the vibration emission
may differ. This may significantly increase the exposure
level over the total working period.
An estimation of the level of exposure to vibration should
also take into account the times when the tool is switched
off or when it is running but not actually doing the job.
This may significantly reduce the exposure level over the
total working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool
and the accessories, keep the hands warm, organisation
of work patterns.
Cordless Concrete Nailer
DCN890
DeWALT declares that these products described under
Technical Data are in compliance with:
2006/42/EC, EN60745-1:2009+A11:2010, EN60745-2-16:2010.
These products also comply with Directive 2014/30/EU and
2011/65/EU. For more information, please contact DeWALT at
the following address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of DeWALT.
Markus Rompel
Director Engineering
DeWALT, Richard-Klinger-Straße 11,
D-65510, Idstein, Germany
26.01.2017
WARNING: To reduce the risk of injury, read the
instruction manual.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
these symbols.
DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in death or
serious injury.
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderate injury.
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may result in
property damage.
Denotes risk of electric shock.
Denotes risk of fire.
General Power Tool Safety Warnings
WARNING: Read all safety warnings and all
instructions. Failure to follow the warnings and
4
Weight
English
Batteries
Chargers/Charge Times (Minutes)
Cat #
VDC
Ah
Weight
kg
DCB107
DCB113
DCB115
DCB118
DCB132
DCB119
DCB546
DCB547
DCB181
DCB182
DCB183/B
DCB184/B
DCB185
DCB187
18/54
18/54
18
18
18
18
18
18
6.0/2.0
9.0/3.0
1.5
4.0
2.0
5.0
1.3
3.0
1.05
1.25
0.35
0.61
0.40
0.62
0.35
0.48
270
420
70
185
90
240
60
140
140
220
35
100
50
120
30
70
90
140
22
60
30
75
22
45
60
85
22
60
30
75
22
45
90
140
22
60
30
75
22
45
X
X
45
120
60
150
X
90
instructions may result in electric shock, fire and/or
serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless)
power tool.
1) Work area safety
a ) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b ) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c ) Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
2) Electrical safety
a ) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of
electric shock.
b ) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if
your body is earthed or grounded.
c ) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d ) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e ) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f ) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3) Personal safety
a ) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
b ) Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal injuries.
c ) Prevent unintentional starting. Ensure the switch
is in the off position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch on
invites accidents.
d ) Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached
to a rotating part of the power tool may result in
personal injury.
e ) Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
f ) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g ) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
4) Power tool use and care
a ) Do not force the power tool. Use the correct power
tool for your application. The correct power tool
will do the job better and safer at the rate for which it
was designed.
5
English
b ) Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c ) Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the
risk of starting the power tool accidentally.
d ) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e ) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f ) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g ) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
•
•
•
Additional Nailer Safety Warnings
•
•
•
5) Battery tool use and care
a ) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.
b ) Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
c ) When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys,
nails, screws or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
d ) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
6) Service
a ) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Nailer Safety Warnings
•
6
Always assume that the tool contains fasteners. Careless
handling of the nailer can result in unexpected firing of
fasteners and personal injury.
Do not point the tool towards yourself or anyone
nearby. Unexpected triggering could discharge a fastener
causing an injury.
Do not actuate the tool unless the tool is placed firmly
against the workpiece. If the tool is not in contact with
the workpiece, the fastener may be deflected away from
your target.
Disconnect the tool from the power source when the
fastener jams in the tool. While removing a jammed
fastener, the nailer may be accidentally activated if it is
plugged in.
•
•
•
•
•
•
•
•
WARNING: When using any nailer, all safety precautions,
as outlined below, should be followed to avoid the risk
of death or serious injury. Read and understand all
instructions before operating the tool.
Hold tool by insulated gripping surfaces when
performing an operation where the pin may contact
hidden wiring. Contact with a “live” wire will make exposed
metal parts of the tool “live” and shock the operator.
Always wear appropriate personal hearing and other
protection during use. Under some conditions and duration
of use, noise from this product may contribute to hearing loss.
Disconnect battery pack from the tool when not in
use. Always remove battery pack and remove fasteners
from magazine before leaving the area or passing the tool
to another operator. Do not carry tool to another work area
in which changing location involves the use of scaffoldings,
stairs, ladders, and the like, with battery pack connected. Do
not make adjustments, perform maintenance or clear jammed
fasteners while battery is in place.
Always use trigger lock-off when tool is not in
immediate use. Using the trigger lock-off will prevent
accidental discharge.
Do not remove, tamper with, or otherwise cause the
tool, trigger or trigger lock-off, to become inoperable.
Do not tape or tie trigger in the on position. Do not remove
spring from contact trip. Make daily inspections for free
movement of trigger. Uncontrolled discharge could result.
Inspect tool before use. Do not operate a tool if any
portion of the tool, trigger, or trigger lock-off is
inoperable, disconnected, altered, or not working
properly. Damaged parts or missing parts should be repaired
or replaced before use. Refer to Maintenance.
Do not alter or modify the tool in any way.
Always assume that the tool contains fasteners.
Do not point the tool at co-workers or yourself at
any time. No horseplay! Work safe! Respect the tool as a
working implement.
Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to lose
control. When tool is not in use, it should be locked in a safe
place, out of the reach of children.
Do not overreach. Maintain proper footing and balance at
all times. Loss of balance may cause personal injury.
English
•
•
•
•
•
•
Use the tool only for its intended use. Do not discharge
fasteners into open air or any material too hard for
the pin to penetrate. Do not use the body of the tool
or top cap as a hammer. Discharged pin may follow
unexpected path and cause injury.
Always keep fingers clear of contact trip to prevent
injury from inadvertent release of the pin.
Refer to the Maintenance and Repairs sections for
detailed information on the proper maintenance of
the tool.
Always operate the tool in a clean, lighted area. Be sure
the work surface is clear of any debris and be careful not to
lose footing when working in elevated environments such
as rooftops.
Fasteners must be driven straight into the material. Do
not tilt the nailer while driving fasteners. Personal injury can
result from ricocheted or jammed pins.
Keep hands and body parts clear of immediate
work area.
WARNING: To avoid injury keep hands and body away
from the front discharge area of the tool.
Do not use tool in the presence of flammable dust, gases
or fumes. This tool produces sparks that can ignite gases or
dust causing an explosion. Driving a pin into another pin may
also cause a spark.
Keep face and body parts away from back of the tool
cap when working in restricted areas. Sudden recoil can
result in impact to the body, especially when nailing into hard
or dense material.
Grip tool firmly to maintain control while allowing tool
to recoil away from work surface as fastener is driven.
Be aware of material thickness when using nailer. A
protruding pin may cause injury.
Do not drive pins blindly into walls, floors or other work
areas. Fasteners driven into live electrical wires, plumbing, or
other types of obstructions can result in injury.
Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use tool
while tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating power
tools may result in serious personal injury.
•
•
•
•
•
•
Residual Risks
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
• Impairment of hearing.
• Risk of personal injury due to flying particles.
• Risk of burns due to accessories becoming hot
during operation.
• Risk of personal injury due to prolonged use.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the battery pack voltage corresponds to the
voltage on the rating plate. Also make sure that the voltage of
your charger corresponds to that of your mains.
Your DeWALT charger is double insulated in
accordance with EN60335; therefore no earth wire
is required.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the DeWALT
service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 3 A.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for
the power input of your charger (see Technical Data). The
minimum conductor size is 1 mm2; the maximum length
is 30 m.
When using a cable reel, always unwind the cable completely.
SAVE THESE INSTRUCTIONS
Chargers
DeWALT chargers require no adjustment and are designed to be
as easy as possible to operate.
Important Safety Instructions for All
Battery Chargers
SAVE THESE INSTRUCTIONS: This manual contains important
safety and operating instructions for compatible battery
chargers (refer to Technical Data).
• Before using charger, read all instructions and
cautionary markings on charger, battery pack, and
product using battery pack.
WARNING: Shock hazard. Do not allow any liquid to get
inside charger. Electric shock may result.
WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA or less.
CAUTION: Burn hazard. To reduce the risk of injury,
charge only DeWALT rechargeable batteries. Other types of
batteries may burst causing personal injury and damage.
CAUTION: Children should be supervised to ensure that
they do not play with the appliance.
NOTICE: Under certain conditions, with the charger
plugged into the power supply, the exposed charging
contacts inside the charger can be shorted by foreign
material. Foreign materials of a conductive nature such
as, but not limited to, steel wool, aluminum foil or any
buildup of metallic particles should be kept away from
7
English
charger cavities. Always unplug the charger from the
power supply when there is no battery pack in the cavity.
Unplug charger before attempting to clean
DO NOT attempt to charge the battery pack with any
chargers other than the ones in this manual. The charger
and battery pack are specifically designed to work together.
These chargers are not intended for any uses other than
charging DeWALT rechargeable batteries. Any other uses
may result in risk of fire, electric shock or electrocution.
Do not expose charger to rain or snow.
Pull by plug rather than cord when disconnecting
charger. This will reduce risk of damage to electric plug
and cord.
Make sure that cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.
Do not use an extension cord unless it is absolutely
necessary. Use of improper extension cord could result in risk
of fire,electric shock, or electrocution.
Do not place any object on top of charger or place
the charger on a soft surface that might block the
ventilation slots and result in excessive internal heat.
Place the charger in a position away from any heat source. The
charger is ventilated through slots in the top and the bottom
of the housing.
Do not operate charger with damaged cord or plug—
have them replaced immediately.
Do not operate charger if it has received a sharp blow,
been dropped, or otherwise damaged in any way. Take it
to an authorised service centre.
Do not disassemble charger; take it to an authorised
service centre when service or repair is required. Incorrect
reassembly may result in a risk of electric shock, electrocution
or fire.
In case of damaged power supply cord the supply cord
must be replaced immediately by the manufacturer,
its service agent or similar qualified person to prevent
any hazard.
Disconnect the charger from the outlet before
attempting any cleaning. This will reduce the risk of
electric shock. Removing the battery pack will not reduce
this risk.
NEVER attempt to connect two chargers together.
The charger is designed to operate on standard
230V household electrical power. Do not attempt to
use it on any other voltage. This does not apply to the
vehicular charger.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Charging a Battery (Fig. B)
1. Plug the charger into an appropriate outlet before inserting
battery pack.
2. Insert the battery pack 10 into the charger, making sure the
battery pack is fully seated in the charger. The red (charging)
light will blink repeatedly indicating that the charging
process has started.
8
3. The completion of charge will be indicated by the red
light remaining ON continuously. The battery pack is fully
charged and may be used at this time or left in the charger.
To remove the battery pack from the charger, push the
battery release button 11 on the battery pack.
NOTE: To ensure maximum performance and life of lithium-ion
battery packs, charge the battery pack fully before first use.
Charger Operation
Refer to the indicators below for the charge status of the battery
pack.
Charge Indicators
Charging
Fully Charged
Hot/Cold Pack Delay*
*The red light will continue to blink, but a yellow indicator light
will be illuminated during this operation. Once the battery pack
has reached an appropriate temperature, the yellow light will
turn off and the charger will resume the charging procedure.
The compatible charger(s) will not charge a faulty battery pack.
The charger will indicate faulty battery by refusing to light or by
displaying problem pack or charger blink pattern.
NOTE: This could also mean a problem with a charger.
If the charger indicates a problem, take the charger and battery
pack to be tested at an authorised service centre.
Hot/Cold Pack Delay
When the charger detects a battery pack that is too hot or too
cold, it automatically starts a Hot/Cold Pack Delay, suspending
charging until the battery pack has reached an appropriate
temperature. The charger then automatically switches to the
pack charging mode. This feature ensures maximum battery
pack life.
A cold battery pack will charge at a slower rate than a warm
battery pack. The battery pack will charge at that slower rate
throughout the entire charging cycle and will not return to
maximum charge rate even if the battery pack warms.
The DCB118 charger is equipped with an internal fan designed
to cool the battery pack. The fan will turn on automatically
when the battery pack needs to be cooled. Never operate the
charger if the fan does not operate properly or if ventilation slots
are blocked. Do not permit foreign objects to enter the interior
of the charger.
Electronic Protection System
XR Li-Ion tools are designed with an Electronic Protection
System that will protect the battery pack against overloading,
overheating or deep discharge.
The tool will automatically turn off if the Electronic Protection
System engages. If this occurs, place the lithium-ion battery
pack on the charger until it is fully charged.
Wall Mounting
These chargers are designed to be wall mountable or to sit
upright on a table or work surface. If wall mounting, locate the
charger within reach of an electrical outlet, and away from a
corner or other obstructions which may impede air flow. Use
the back of the charger as a template for the location of the
mounting screws on the wall. Mount the charger securely using
drywall screws (purchased separately) at least 25.4 mm long
with a screw head diameter of 7–9 mm, screwed into wood to
an optimal depth leaving approximately 5.5 mm of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using a
cloth or soft non-metallic brush. Do not use water or any
cleaning solutions. Never let any liquid get inside the tool;
never immerse any part of the tool into a liquid.
Battery Packs
Important Safety Instructions for All
Battery Packs
When ordering replacement battery packs, be sure to include
catalogue number and voltage.
The battery pack is not fully charged out of the carton. Before
using the battery pack and charger, read the safety instructions
below. Then follow charging procedures outlined.
READ ALL INSTRUCTIONS
•
•
•
•
•
•
•
•
Do not charge or use battery in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Inserting or removing the battery from the charger may
ignite the dust or fumes.
Never force battery pack into charger. Do not modify
battery pack in any way to fit into a non-compatible
charger as battery pack may rupture causing serious
personal injury.
Charge the battery packs only in DeWALT chargers.
DO NOT splash or immerse in water or other liquids.
Do not store or use the tool and battery pack in
locations where the temperature may reach or exceed
40 ˚C (104 ˚F) (such as outside sheds or metal buildings
in summer).
Do not incinerate the battery pack even if it is severely
damaged or is completely worn out. The battery pack can
explode in a fire. Toxic fumes and materials are created when
lithium-ion battery packs are burned.
If battery contents come into contact with the skin,
immediately wash area with mild soap and water. If
battery liquid gets into the eye, rinse water over the open eye
for 15 minutes or until irritation ceases. If medical attention
is needed, the battery electrolyte is composed of a mixture of
liquid organic carbonates and lithium salts.
Contents of opened battery cells may cause respiratory
irritation. Provide fresh air. If symptoms persists, seek medical
attention.
WARNING: Burn hazard. Battery liquid may be flammable
if exposed to spark or flame.
English
WARNING: Never attempt to open the battery pack for
any reason. If battery pack case is cracked or damaged,
do not insert into charger. Do not crush, drop or damage
battery pack. Do not use a battery pack or charger that
has received a sharp blow, been dropped, run over or
damaged in any way (i.e., pierced with a nail, hit with
a hammer, stepped on). Electric shock or electrocution
may result. Damaged battery packs should be returned to
service centre for recycling.
WARNING: Fire hazard. Do not store or carry the
battery pack so that metal objects can contact
exposed battery terminals. For example, do not place
the battery pack in aprons, pockets, tool boxes, product kit
boxes, drawers, etc., with loose nails, screws, keys, etc.
CAUTION: When not in use, place tool on its side on
a stable surface where it will not cause a tripping
or falling hazard. Some tools with large battery packs
will stand upright on the battery pack but may be easily
knocked over.
Transportation
WARNING: Fire hazard. Transporting batteries can
possibly cause fire if the battery terminals inadvertently
come in contact with conductive materials. When
transporting batteries, make sure that the battery
terminals are protected and well insulated from materials
that could contact them and cause a short circuit.
DeWALT batteries comply with all applicable shipping
regulations as prescribed by industry and legal standards which
include UN Recommendations on the Transport of Dangerous
Goods; International Air Transport Association (IATA) Dangerous
Goods Regulations, International Maritime Dangerous Goods
(IMDG) Regulations, and the European Agreement Concerning
The International Carriage of Dangerous Goods by Road (ADR).
Lithium-ion cells and batteries have been tested to section 38.3
of the UN Recommendations on the Transport of Dangerous
Goods Manual of Tests and Criteria.
In most instances, shipping a DeWALT battery pack will be
excepted from being classified as a fully regulated Class 9
Hazardous Material. In general, only shipments containing a
lithium-ion battery with an energy rating greater than 100 Watt
Hours (Wh) will require being shipped as fully regulated Class 9.
All lithium-ion batteries have the Watt Hour rating marked on
the pack. Furthermore, due to regulation complexities, DeWALT
does not recommend air shipping lithium-ion battery packs
alone regardless of Watt Hour rating. Shipments of tools with
batteries (combo kits) can be air shipped as excepted if the Watt
Hour rating of the battery pack is no greater than 100 Whr.
Regardless of whether a shipment is considered excepted
or fully regulated, it is the shipper's responsibility to consult
the latest regulations for packaging, labeling/marking and
documentation requirements.
The information provided in this section of the manual is
provided in good faith and believed to be accurate at the time
the document was created. However, no warranty, expressed or
implied, is given. It is the buyer’s responsibility to ensure that its
activities comply with the applicable regulations.
9
English
Transporting the FLEXVOLTTM Battery
The DeWALT FLEXVOLTTM battery has two modes: Use and
Transport.
Use Mode: When the FLEXVOLTTM battery stands alone or is in
a DeWALT 18V product, it will operate as an 18V battery. When
the FLEXVOLTTM battery is in a 54V or a 108V (two 54V batteries)
product, it will operate as a 54V battery.
Transport Mode: When the cap is attached to the FLEXVOLTTM
battery, the battery is in Transport mode. Keep the cap for
shipping.
When in Transport mode, strings
of cells are electrically
disconnected within the pack
resulting in 3 batteries with a
lower Watt hour (Wh) rating as compared to 1 battery with a
higher Watt hour rating. This increased quantity of 3 batteries
with the lower Watt hour rating can exempt the pack from
certain shipping regulations that are imposed upon the higher
Watt hour batteries.
For example, the Transport Example of Use and Transport Label Marking
Wh rating might indicate
3 x 36 Wh, meaning 3
batteries of 36 Wh each.
The Use Wh rating might
indicate 108 Wh (1 battery implied).
Do not expose to water.
Have defective cords replaced immediately.
Charge only between 4 ˚C and 40 ˚C.
Only for indoor use.
Discard the battery pack with due care for the
environment.
Charge DeWALT battery packs only with designated
DeWALT chargers. Charging battery packs other
than the designated DeWALT batteries with a
DeWALT charger may make them burst or lead to
other dangerous situations.
Do not incinerate the battery pack.
USE (without transport cap). Example: Wh rating
indicates 108 Wh (1 battery with 108 Wh).
TRANSPORT (with built-in transport cap). Example:
Wh rating indicates 3 x 36 Wh (3 batteries of 36 Wh).
Storage Recommendations
Battery Type
1. The best storage place is one that is cool and dry away
from direct sunlight and excess heat or cold. For optimum
battery performance and life, store battery packs at room
temperature when not in use.
2. For long storage, it is recommended to store a fully charged
battery pack in a cool, dry place out of the charger for
optimal results.
NOTE: Battery packs should not be stored completely depleted
of charge. The battery pack will need to be recharged before
use.
The DCN890 operates on a 18 volt battery pack.
These battery packs may be used: DCB181, DCB182, DCB183,
DCB183B, DCB184, DCB184B, DCB185, DCB187, DCB546,
DCB547. Refer to Technical Data for more information.
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual, the labels
on the charger and the battery pack may show the following
pictographs:
Read instruction manual before use.
See Technical Data for charging time.
Do not probe with conductive objects.
Do not charge damaged battery packs.
Package Contents
The package contains:
1 Concrete nailer
1Charger (P2 models only)
2 Battery packs (P2 models only)
1Kitbox (P2 models only))
1 Drywall Contact Trip (DCN8904)
1 Non-Magnetic Contact Trip (DCN8903)
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
10
English
Visible radiation. Do not stare into light.
13-57 mm
2.6–3.7 mm
33
15˚
Length of nails.
Nail thickness.
Loading capacity.
Suitable nail collation angle.
Date Code Position (Fig. B)
The date code 22 , which also includes the year of manufacture,
is printed into the housing.
Example:
2017 XX XX
Year of Manufacture
Description (Fig. A)
1
2
3
4
5
6
7
8
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
9 Low battery & jam/stall
Trigger
indicator lights (x2)
Trigger lock-off
10 Battery pack
Speed selection switch
Sequential and Rapidcycle 11 Battery release button
12 Magazine
switch
13 Magazine support leg
Contact trip release lever
14 Magazine release lever
Contact trip
15 Pusher
Removable top stand
16 Utility hook
Stall release lever
Intended Use
Your concrete nailer is intended ONLY for use in driving pins
into structural steel OR concrete base materials OR fastening
wood to concrete. This tool has two operating modes, a
sequential operating mode and a unique rapid sequential
operating mode (RapidCycle). Read the section of the manual
Selecting the Mode before using the tool to make sure you are
selecting the proper mode for your application.
DO NOT use under wet conditions or in the presence of
flammable liquids or gases.
Your concrete nailer is a professional power tool.
Only DeWALT pins recommended by the pin hardware
manufacturer and meeting applicable building code
requirements should be used in this tool.
This tool is intended for use by construction professionals.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
Dry Fire Lock Out
The concrete nailer is equipped with a dry fire lockout which
prevents the tool from actuating when the magazine is nearly
empty. When 3 pins remain in the magazine, the tool ceases to
operate. Refer to Loading the Tool to reload a stick of collated
pins.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
WARNING: Use only DeWALT battery packs and chargers.
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
NOTE: Make sure your battery pack 10 is fully charged.
To Install the Battery Pack into the Tool
Handle
1. Align the battery pack 10 with the rails inside the tool’s
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button 11 and firmly pull the battery pack
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some DeWALT battery packs include a fuel gauge which
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge button.
A combination of the three green LED lights will illuminate
designating the level of charge left. When the level of charge
in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
NOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Utility Hook (Fig. C)
The DeWALT cordless nailers include an integrated utility
hook 16 and can be attached to either side of the tool to
accommodate left- or right-handed users.
If the hook is not desired at all, it can be removed from the tool.
11
English
To Remove Utility Hook
1. Remove battery pack from tool.
2. To switch the tool from right- to left-hand usage simply
remove the screw 17 from the opposite side of the tool and
reassemble on the other side.
3. Replace battery pack.
WARNING: Remove pins from magazine before making
any adjustments or servicing this tool. Failure to do so may
result in serious injury.
WARNING: Disconnect battery pack from tool before
making any adjustments, changing accessories, servicing,
or moving the tool. Such preventative safety measures
reduce the risk of starting the tool accidentally.
CAUTION: When not in use, place tool on its side on
a stable surface where it will not cause a tripping or
falling hazard. Some tools with large battery packs will
stand upright on the battery pack but may be easily
knocked over.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
WARNING: Read the section titled Nailer Safety
Warnings at the beginning of this manual. Always wear
eye and ear protection when operating this tool. Keep the
nailer pointed away from yourself and others. For safe
operation, complete the following procedures and checks
before each use of the nailer.
1. Wear proper eye, hearing and respiratory protection.
2. Remove battery pack from tool.
3. Lock the pusher 15 in the back position and remove all pins
from the magazine.
4. Check for smooth and proper operation of contact trip
and pusher latch. Do not use tool if either assembly is not
functioning properly. NEVER use a tool that has the contact
trip restrained in the up position.
5. NEVER use a tool that has damaged parts.
WARNING: To reduce the risk of personal injury,
disconnect battery pack from tool before performing
maintenance, clearing a jammed pin, leaving work area,
moving tool to another location or handing the tool to
another person.
Proper Hand Position (Fig. D)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle as
shown in Fig. D.
Preparing the Tool (Fig. A)
NOTICE: NEVER spray or in any
other way apply lubricants or
cleaning solvents inside the tool.
This can seriously affect the life and
performance of the tool.
NOTE: The battery pack is not fully
charged out of the carton. Follow instructions outlined (refer to
Charging Operations).
1. Read the Nailer Safety Warnings section of this manual.
2. Wear eye and ear protection.
3. Remove battery from tool.
4. Ensure magazine is empty of all fastners.
5. Check for smooth and proper operation of contact trip and
pusher latch 15 . Do not use tool if either assembly is not
functioning properly. NEVER use a tool that has the contact
trip restrained in the actuated position.
6. Keep tool pointed away from yourself and others.
7. Insert fully charged battery pack.
Using the Trigger Lock-off (Fig. E)
WARNING: To reduce the risk of serious personal injury,
do not keep trigger depressed when tool is not in use. Keep
the trigger lock-off switch LOCKED (Fig. E) when the tool
is not in use.
WARNING: To reduce the risk of serious personal injury,
lock off trigger, disconnect battery pack from tool and
remove pins from magazine before making adjustments.
Each DeWALT nailer is equipped with a trigger lock-off 2 which
when pushed to the right as shown in Figure E, prevents the
tool from firing a pin by locking the trigger and bypassing
power to the motor.
When the trigger lock-off is pressed to the left, the tool will be
fully operational. The trigger lock-off should always be locked off
(Fig. E) whenever any adjustments are made or when tool is not
in immediate use.
NOTICE: Do not store tool with battery pack installed. To
prevent damage to the pack and to ensure best battery
life, store battery packs out of the tool or charger in a cool,
dry location.
Loading the Tool (Fig. F)
WARNING: Keep the tool pointed away from yourself and
others.
WARNING: Never load pins with the contact trip or trigger
activated.
12
WARNING: Always remove battery pack before loading or
unloading pins.
CAUTION: Keep fingers clear of pusher latch track to
prevent injury.
WARNING: The trigger lock-off should always be engaged
whenever any adjustments are made or when tool is not
in use.
WARNING: Fasteners used to install metal connectors
must meet the requirements of the applicable building
codes and must be installed in compliance with code
requirements and metal connector hardware supplier
specifications. Failure to properly install connectors may
result in structural failures.
1. Turn the nailer upside down.
2. Slide the spring-loaded pusher latch 15 to the base of the
magazine to lock it into place.
3. Drop pin strips into the loading slot of the magazine,
making sure the pin heads align correctly with the slot
opening. (Refer to Technical Data to determine compatible
size.)
4. Keeping fingers clear of the track, close the magazine by
releasing the pusher latch. Carefully allow the latch to slide
forward and engage the pin strip.
Unloading the Tool
WARNING: The trigger lock-off should always be locked
off whenever any adjustments are made or when tool is
not in use.
1. Remove the battery from your nailer.
2. Slide the spring-loaded pusher latch to the base of the
magazine to lock it into place.
3. Tip the tool up until the fastener strip slides freely out of the
magazine.
4. With battery removed, check the nosepiece to verify there
are no pins remaining.
NOTE: The tool is equipped with a magnet in the nose area for
improved tool performance. When unloading, always verify that
the small sticks of pins are not held to the magnetized nose
piece.
Speed Setting Summary (Fig. A, G, H)
This nailer is equipped with a speed selection switch 3 to adjust
the tool when driving into different materials.
Speed 1: Softer materials (low strength concrete/cinder block)
Speed 2: Medium hardness materials (High strength concrete)
Speed 3: Hard materials (Structural steel)
In the event pins are not driving to depth in speed 1, you may
have to switch to speed 2 or 3 for additional driving power.
NOTICE: Driving pins into soft materials at high
speed settings will cause excessive wear to your tool
and may result in early failures.
English
Speed Setting
1
2
3
Application
Typical Pin Length
Fastening Steel/Wood to Low Strength
19-25 mm
Concrete/Masonry (<4000 psi)
Fastening Steel/Wood to High Strength
19-29 mm
Concrete (>4000 psi)
Fastening to structural steel;
13-57 mm
2x4 to Concrete
WARNING: Pins must be driven straight into the material.
Do not tilt nailer while driving fasteners. Refer to Fig. H.
Pin retention values improve when the tool is fired
perpendicular to the material.
The tool can be fired/actuated by pulling the trigger 1 in one
of two modes: sequential mode or RapidCycle mode. Refer
to Selecting the Mode for detailed instructions for firing in
each mode.
Selecting the Mode (Fig. A, G)
To select standard sequential mode, slide the mode selector
switch 4 to display the single arrow ( ) icon.
To select rapid sequential operating mode (RapidCycle), slide
the mode selector switch 4 to display the double arrow ( )
icon.
NOTE: Battery life in RapidCycle mode will be shorter than
in standard sequential mode. Leaving the tool in standard
sequential will give maximum battery life.
Sequential Mode
The sequential mode is used for intermittent nailing. It offers the
maximum battery life for driving pins.
1. Using the mode selector switch 4 , select the
sequential mode.
2. Release the trigger lock-off 2 .
3. Push the contact trip 6 against the work surface.
4. Pull the trigger switch 1 to actuate the tool.
5. Release the trigger and raise the nailer from the
work surface.
6. Repeat steps 3–5 to actuate the next nail.
RapidCycle Mode
In RapidCycle mode, the motor rotation speed is automatically
restored after driving a pin to allow fast consecutive nailing.
While offering the ability to drive more pins in less time, this
mode quickly depletes the battery charge.
1. Using the mode selector switch 4 to select the RapidCycle
mode.
2. Release the trigger lock-off 2 .
3. Push the contact trip 6 against the work surface.
4. Pull the trigger switch 1 to actuate the tool.
5. Release the trigger and raise the nailer from the work
surface. NOTE: The tool motor returns to full speed
automatically without the contact trip 6 being depressed.
6. Repeat steps 3–5 to actuate the next nail.
13
English
Pin/Fastener Troubleshooting
STEEL
Pin does not penetrate the surface.
Properly driven pin
Cause:
-- Speed setting too low
-- Material to hard for pin type
Action:
-- Increase tool speed setting
Over driven pin
CONCRETE
Pin does not hold in the concrete.
Cause:
-- Too hard/high strength
concrete
-- Hard or large aggregate
in concrete
Action:
-- Use shorter pin.
-- Switch to higher speed setting.
Pin breaks or bends.
Cause:
-- Pin too long
-- Speed setting too low
-- Material to hard for pin type
Action:
-- Use shorter pin.
-- Switch to higher speed setting.
Pin does not drive deep enough.
Cause:
-- Pin too long
-- Speed setting too low
Action:
-- Use shorter pin.
-- Switch to higher speed setting.
Pin drives too deep.
Cause:
-- Pin too short for application
-- Speed setting too high
Action:
-- Use longer pin.
-- Switch to lower speed setting.
Pin does not hold in the steel.
Cause:
-- Steel base material too thin
Action:
-- Use alternative means to secure
base material.
Headlights/LED Indicator (Fig. A)
There are low battery and jam/stall indicator lights 9 located on
the front of the tool on each side of the magazine.
LOW BATTERY
Replace battery with a charged pack.
HOT PACK
Let the battery cool or replace it with a
cool pack.
Pin bends.
Cause:
-- Pin hit large aggregate on entry
-- Too hard/high strength
concrete
-- Pit hit rebar just under surface
Action:
-- Use shorter pin.
-- Make sure nailer is
perpendicular to the work
surface.
-- Move 8 cm and try again.
JAM/STALL CONDITION
Rotate the stall release lever to release.
Refer to Stall Release or Clearing a
Jammed Pin.
HOT TOOL (Both LEDs Flashing)
Let the tool cool down before continuing
use.
or any other
combination.
14
ERROR
Reset tool by removing and reinserting
battery pack or cycling trigger lock off.
If error code persist, take tool to an
authorised DeWALT service center.
English
Stall Release (Fig. I)
If the nailer is used in harder material where all available energy
in the motor is used to drive a fastener, the tool may stall.
The driver will not complete the drive cycle and the jam/stall
indicator will flash. Rotate the stall release lever 8 on the tool
and the mechanism will release. NOTE: The tool will disable
itself and not reset until the battery pack has been removed
and reinserted. If the driver does not automatically return to
the home position, proceed to Clearing a Jammed Pin. If the
unit continues to stall please review the material and fastener
length to be sure that it is not too rigorous an application. The
nailer could also be overheated and needs time to cool before
further use.
NOTE: Should pins jam frequently or the driver continually fail
to reset, have tool serviced by an authorised DeWALT service
centre.
Cold Weather Operation
When operating tools at temperatures below freezing:
1. Keep tool as warm as possible prior to use.
2. Actuate the tool 10 or 15 times into scrap lumber before
using.
Hot Weather Operation
Tool should operate normally. However, keep tool out of direct
sunlight as excessive heat can deteriorate bumpers and other
rubber parts resulting in increased maintenance.
Clearing a Jammed Pin (Fig. A, J)
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, disconnect battery pack from tool before
making any adjustments, changing accessories,
servicing, or moving the tool. Such preventative safety
measures reduce the risk of starting the tool accidentally.
CAUTION: When removing a jammed pin, DO NOT
orient the nailer with the nose up or with the battery
foot up. Positioning the nailer this way makes the
jammed pin or pieces of the pin more likely to be ingested
into the nailer. If any portion of a pin is ingested into the
tool, the pin should be retrieved by removing the top cap.
If a pin becomes jammed in the nosepiece, keep the tool
pointed away from you and follow these instructions to clear:
1. Remove battery pack from tool and engage trigger lock-off.
2. After laying the tool on its side, slide the spring-loaded
pusher latch 15 to the base of the magazine to lock it into
place and unload pin strip.
3. Rotate the magazine release lever 14 and rotate the
magazine 12 forward.
4. Remove jammed/bent pin, using pliers if necessary. The
contact trip can be removed if necessary. Refer to Contact
Trip Replacement.
CAUTION: If any portion of a pin is ingested into the tool,
the pin should be retrieved by removing the top cap.
5. If the driver is in the down position, rotate the stall release
lever on the top of the nailer.
NOTE: If the driver will not reset after rotating the stall
release lever, manually resetting the blade with a long screw
driver may be necessary.
6. Rotate the magazine back into position under the nose of
the tool and close the magazine release lever.
7. Reinsert battery pack.
NOTE: The tool will disable itself and not reset until the
battery pack has been removed and reinserted.
8. Reinsert pins into magazine (refer to Loading the Tool).
9. Release the pusher latch.
10. Disengage the trigger lock-off when ready to
continue nailing.
Your DeWALT power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
DAILY MAINTENANCE CHART
ACTION
Clean magazine, pusher, and contact trip
mechanism.
WHY
Permits smooth operation of magazine, reduces
wear, and prevents jams.
HOW
Blowing off the tool with compressed air is the
most effective way to clean the tool. The use
of oils, lubricants periodically or solvents is not
recommended as they tend to attract debris
and/or damage the plastic parts of the tool.
ACTION
Before each use, check to ensure all screws and
fasteners are tight and undamaged.
WHY
Prevents jams and premature failure of tool parts.
HOW
Tighten loose screws using the appropriate hex
wrench or screwdriver.
Lubrication
NOTICE: NEVER spray or in
any other way apply lubricants
or cleaning solvents inside the
tool. This can seriously affect
the life and performance of
the tool.
DeWALT tools are properly
lubricated at the factory and are ready for use. However, it is
recommended that, once a year, you take or send the tool to a
certified service centre for a thorough cleaning and inspection.
15
English
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories
WARNING: Since accessories, other than those offered
by DeWALT, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only DeWALT recommended
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Contact Trip Replacment (Fig. F)
For some applications, using a different contact trip may be
desirable.
WARNING: For your own safety, read the tool instruction
manual before using any accessory. Failure to heed
these warnings may result in personal injury and serious
damage to the tool and the accessory. When servicing this
tool, use only identical replacement parts.
To Replace Contact Trip:
1. Push down on the contact trip release lever 5
2. Pull the contact trip 6 out of the nose of the tool.
3. Hold down the trip release lever
4. With the contact trip alignment marker facing up, as shown
in Figure K, insert the contact trip fully into the tool nose.
5. Release the lever.
DCN8901 Driver Blade Replacement Kit
(Fig. L, M, N)
WARNING: For your own safety, read the tool instruction
manual before using any accessory. Failure to heed
these warnings may result in serious personal injury and
damage to the tool and the accessory. When servicing this
tool, use only identical replacement parts.
NOTICE: All the mechanical parts of the driver replacment
kit are shown for convenience and verification of inclusion.
To Change a Worn Driver Blade:
1. Using a T-20 Torx, loosen the four screws 18 on either side
of the unit.
2. Remove the four screws and the removable top stand 7 .
Refer to Figure L.
3. Remove housing end cap 19 . Refer to Figure L.
16
4. Push up on the rear of the driver 20 until you hear a click,
then push the driver forward while holding it in this position
until it passes the upper bumper assembly 22 .
5. Remove guide rods 21 . Refer to Figure M.
6. Remove upper bumper assembly.
7. Lift the rear of driver until at an angle and pull the driver out.
Refer to Figure N.
8. Replace driver and follow steps in reverse to reassemble
9. Ensure new driver slides smoothly through the tool before
full reassembly.
10. Return the driver, guide rods, bumpers, housing end cap,
and removable top stand back onto the unit. It is important
to try the alignment of the driver and the flywheel before
screwing the housing end cap back on to the unit. This
can be done by connecting a battery and pushing then
releasing the nose of the unit against a bench or hard
surface. This will start the motor spinning.
NOTE: When the driver and the flywheel are correctly
aligned, you will hear the motor coast back down from
full speed. If the driver and the flywheel are not correctly
aligned, the motor may not start up, may slow down much
faster than normal along with a loud grinding noise from
the unit. If this happens remove and reseat the driver
making sure the bumpers are seated correctly.
WARNING: Always test the unit by firing 15 mm,
20 mm or 25 mm pins in Speed 1 into scrap material, to
ensure that the tool is working properly. If tool does not
operate properly, contact a recognised DeWALT service
centre immediately.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
our environment:
• Run the battery pack down completely, then remove it from
the tool.
• Li-Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.
English
TROUBLESHOOTING GUIDE
WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack before making any
adjustments or removing/installing attachments or accessories. An accidental start-up can cause injury.
SYMPTOM
Motor does not run with contact
trip depressed
CAUSE
Trigger lock in locked position
Dryfire lock out engaged, blocking contact trip from
traveling fully
Tool is stalled, locking the motor from rotating
Tool is hot. (Check LED indicator to verify these
conditions.)
Battery is hot. (Check LED indicator to verify these
conditions.)
Bent contact trip
Motor stops running after 5 seconds
Terminals are dirty or damaged
Damaged internal electronics
Damaged Trigger
Tool does not actuate (motor runs Dryfire lock out engaged, blocking contact trip from
but will not fire)
traveling fully
Low battery charge or damaged battery
Motor starts up but generates a
lot of noise
Jammed pin/drive blade not returned to home
position
Damaged driver
Jammed internal mechanism
Damaged internal electronics
Jammed pin and driver is stuck in down position
Damaged driver
Driver blade continues to get stuck Jammed pin and driver is stuck in down position
in down position
Debris in nosepiece
Damaged or worn driver
FIX
Unlock trigger lock.
Load more pins into magazine.
Rotate the stall release lever on the tool and the mechanism will
release. If driver does not return, remove battery and manually push
driver back to home position.
Let the tool cool down before continuing use.
Let the battery cool or replace it with a cool pack.
See authorised service centre.
Normal operation, release contact trip and redepress.
See authorised service centre.
See authorised service centre.
See authorised service centre.
Load pins into magazine.
Check charge level if pack shows state-of-charge.
Charge or replace battery pack if necessary.
Remove battery, clear jammed pin, cycle stall release lever, (push driver
up manually if necessary) reinsert battery pack.
Replace driver with kit.
See authorised service centre.
See authorised service centre.
Use stall release lever, clear and jammed pins, and return driver
manually if necessary.
Replace driver with kit.
Use stall release lever, clear any jammed pins, and return driver
manually if necessary.
Clean nose area and watch closely for small pieces of broken pins stuck
in the track. Refer to Clearing a Jammed Pin.
Replace driver with kit.
17
English
SYMPTOM
Tool operates but does not drive
fasteners fully
CAUSE
Speed select setting in wrong position.
Tool not firmly applied to workpiece
Material and fastener length
Use of incorrect speed
Tool operates, but no fastener
is driven
Jammed nail
Damaged or worn driver tip
Damaged actuation mechanism
No pins in magazine
Wrong size or angle pins
Debris in nosepiece
Debris in magazine
Damaged or worn driver
Worn magazine
Damaged pusher spring
Wrong size or angle pins
Magazine not secured after previous jam clear/
inspection
Damaged or worn driver
Material and fastener length
Debris in nosepiece
Driver blade does not slide
backward and forward smoothly
through its firing path
18
FIX
Set speed to appropriate setting.
Apply adequate force to tool securing it tightly to workpiece. See
instruction manual.
If the unit continues to stall (forcing the need to rotate the stall release
lever) choose the appropriate material and fastener length that is not
too rigorous of an application.
If trying to drive longer pins in soft woods, or driving pins into harder
materials using speed 1 - adjust speed setting to position 2.
Replace driver with kit.
See authorised service centre.
Load pins in magazine.
Use only the recommended pins. Refer to Technical Data.
Clean nose area and watch closely for small pieces of broken pins stuck
in the track.
Clean magazine
Replace driver with kit.
Replace magazine. See authorised service centre.
Replace spring. See authorised service centre.
Use only the recommended pins Refer to Technical Data.
Make sure to magazine is latched properly.
Replace driver.
If the unit continues to stall (forcing the need to rotate the stall release
lever) choose the appropriate material and fastener length that is not
too rigorous an application.
Clean nose area and watch closely for small pieces of broken pins stuck
in the track.
Replace springs. See authorised service centre.
Load more pins in magazine to disengage dryfire lockout.
Damaged pusher spring
Dry fire lock out is engaged with only 2–4 pins
remaining in magazine and the user is applying
excessive force to contact trip, overriding the lockout
Tool is not yet run-in
New tools can take 100–500 pins for parts to mesh and wear in
together. Drive shorter pins during this period if experiencing difficulty
fully driving pins.
Use of incorrect speed
If trying to drive longer pins in soft materials, or driving pins into harder
materials using speed 1 - adjust speed setting to position 2 or 3.
Worn magazine
Replace magazine. See authorised service centre.
Driver blade is bent
Replace driver.
19
20
21
Belgique et
Luxembourg België en Luxemburg
DeWALT - Belgium BVBA
Egide Walschaertsstraat 16
2800 Mechelen
Tel: NL 32 15 47 37 63
Tel: FR 32 15 47 37 64
Fax:
32 15 47 37 99
www.dewalt.be
enduser.BE@SBDinc.com
Danmark
DeWALT (Stanley Black&Decker AS)
Roskildevej 22
2620 Albertslund
Tel:
Fax:
www.dewalt.dk
kundeservice.dk@sbdinc.com
Deutschland
DeWALT
Richard Klinger Str. 11
65510 Idstein
Tel:06126-21-0
Fax:06126-21-2770
www.dewalt.de
infodwge@sbdinc.com
Ελλάς
DeWALT (Ελλάς) Α.Ε.
EΔΡΑ-ΓΡΑΦΕΙΑ : Στράβωνος 7
& Λ. Βουλιαγμένης, Γλυφάδα 166 74, Αθήνα
SERVICE : Ημερος Τόπος 2 (Χάνι Αδάμ) – 193 00 Ασπρόπυργος
Τηλ:00302108981616
Φαξ:00302108983570
www.dewalt.gr
Greece.Service@sbdinc.com
España
DeWALT Ibérica, S.C.A.
Parc de Negocios “Mas Blau”
Edificio Muntadas, c/Bergadá, 1, Of. A6
08820 El Prat de Llobregat (Barcelona)
Tel:
Fax:
934 797 400
934 797 419
www.dewalt.es
respuesta.postventa@sbdinc.com
France
DeWALT
5, allée des Hêtres
BP 60105, 69579 Limonest Cedex
Tel:
Fax:
04 72 20 39 20
04 72 20 39 00
www.dewalt.fr
scufr@sbdinc.com
Schweiz
Suisse
Svizzera
DeWALT
In der Luberzen 42
8902 Urdorf
Tel:
Fax:
044 - 755 60 70
044 - 730 70 67
www.dewalt.ch
service@rofoag.ch
Ireland
DeWALT
Building 4500, Kinsale Road
Cork Airport Business Park
Cork, Ireland
Tel:00353-2781800
Fax:
01278 1811
www.dewalt.ie
Sales.ireland@sbdinc.com
Italia
DeWALT
via Energypark 6
20871 Vimercate (MB), IT
Tel: Fax: 800-014353
39 039-9590200
39 039-9590311
www.dewalt.it
Nederlands
DeWALT
Netherlands BVPostbus 83,
6120 AB BORN
Tel:
Fax:
31 164 283 063
31 164 283 200
www.dewalt.nl
Norge
DeWALT
Postboks 4613
0405 Oslo, Norge
Tel: Fax: 45 25 13 00
45 25 08 00
www.dewalt.no
kundeservice.no@sbdinc.com
Österreich
DeWALT
Werkzeug Vertriebsges m.b.H
Oberlaaerstrasse 248, A-1230 Wien
Tel: Fax: 01 - 66116 - 0
01 - 66116 - 614
www.dewalt.at
service.austria@sbdinc.com
Portugal
DeWALT
Ed. D Dinis, Quina da Fonte
Rua dos Malhoes 2 2A 2º Esq.
Oeiras e S. Juliao da Barra, paço de Arcos e Caxias
2770 071 Paço de Arcos
Tel: Fax: +351 214667500
+351214667580
www.dewalt.pt
resposta.posvenda@sbdinc.com
Suomi
DeWALT
PL47
00521 Helsinki, Suomi
Puh: Faksi:
010 400 4333
0800 411 340
www.dewalt.fi
asiakaspalvelu.fi@sbdinc.com
Sverige
DeWALT
BOX 94
43122 Mölndal
Sverige
Tel:
Fax: 031 68 61 60
031 68 60 08
www.dewalt.se
kundservice.se@sbdinc.com
Türkiye
Sanayi ve Ticareet Bakanlığı tebliğince kullanim ömrü 7 yıldır.
Stanley Black & Decker Turkey Alet Üretim San. Tic. Ltd.Şti.
Kozyataği Mh Değirmen Sk.
Nida Kule No: 18 Kat: 6, 34742
Kadıköy, İstanbul, Türkiye
Tel: Faks:
+90 216 665 2900
+90 216 665 2901
www.dewalt.com.tr
info-tr@sbdinc.com
United
Kingdom
DeWALT, 210 Bath Road;
Slough, Berks SL1 3YD
Tel: Fax: 01753-567055
01753-572112
www.dewalt.co.uk
emeaservice@sbdinc.com
Australia
DeWALT
810 Whitehorse Road Box Hill
VIC 3103 Australia
Tel: Aust 1800 338 002
Tel: NZ 0800 339 258
www.dewalt.com.au
www.dewalt.co.nz
Middle East Africa
DeWALT
P.O. Box - 17164,
Jebel Ali Free Zone (South), Dubai, UAE
Tel: Fax: www.dewalt.ae
Service.MEA@sbdinc.com
N493209
70 20 15 10
70 22 49 10
971 4 812 7400
971 4 2822765
04/17
Download PDF

advertising