FSMH13E10 | Black&Decker FSMH13E10 STEAM MOP instruction manual

www.blackanddecker.co.uk
FSMH13E5
FSMH13E10
13
11
10
12
1
2
3
9
4
5
8
6
7
2
FSMHI3E5
7
14
15
16
A
FSMHI3E10
7
17
18
19
21
22
16
20
B
8
9
5b
5a
5
6
C
D
3
ENGLISH
(Original instructions)
6
7
E
19
13
13a
F
4
11
3
10
G
4
H
(Original instructions)
Intended use
Your BLACK+DECKERTM FSMH13E5, FSMH13E10 steam
mop has been designed for sanitising and cleaning sealed
hardwood, sealed laminate, linoleum, vinyl, ceramic tile,
stone and marble floors. This appliance is intended for indoor
household use only.
Safety Instructions
Warning! Read all Safety,
t
Maintenance, Service' manual
carefully before operating
this appliance. Read all of this
manual carefully before operating this appliance.
Safety of others
appliance is not to be used if it
has been dropped, if there are visible
signs of damage or if it is leaking;
u Keep the appliance out of reach of
children when it is energized or cooling
down.
u
The
Labels on appliance
The following pictograms along with the
date code are shown on the appliance.
CAUTION Hot Steam
Features
1. On/off switch
appliance can be used by children 2. Steam operate button
3. Water tank access tab
aged from 8 years and above and
4. Water tank
persons with reduced physical, sen 5. Steam head connector
sory or mental capabilities or lack of
6. Steam head
experience and knowledge if they have 7. Steam head cleaning pad
8. Handle connector button
been given supervision or instruction
9. Handle
concerning use of the appliance in a
10. Cable tidy hook
safe way and understand the hazards 11. Grip
involved.
12. Power cable
13. Accessory adaptor
u Children shall not play with the appliance. Cleaning and user maintenance 14. Small brush (plastic bristles)
15. Small squeegee
shall not be made by children without
16. Grout brush
supervision.
17. Large squeegee
u If the supply cord is damaged, it must
18. Sock pad for squeegee
19. Large brush (plastic bristles)
be replaced by the manufacturer, its
20. Small brush (copper bristles)
service agent or similarly qualified
21. Small brush x2 (plastic bristles)
persons in order to avoid a hazard.
22. Carpet Glider
u The plug must be removed from the
socket-outlet before cleaning or mainAssembly
taining the appliance.
u The liquid or steam must not be
Warning! Before attempting any of the following
make sure that the appliance is
directed towards equipment contain@ instructions,
switched off and unplugged and the appliance is
ing electrical components, such as the
cold and does not contain any water.
interior of ovens.
u The appliance shall not be left unatAttaching the handle (Fig. C)
tended while it is connected to the sup- u Slide the bottom end of the handle (9) into the top end of
the steam mop body until the handle connector button (8)
ply mains;
u
This
ENGLISH
clicks into place.
5
ENGLISH
(Original instructions)
Attaching the steam head (Fig. D)
u
Connect the steam mop body to the steam head (6) via
the steam head connector (5), ensuring the connection
button (5a) clicks into place in the the opening (5b).
Attaching a cleaning pad (Fig. E)
Replacement cleaning pads are available from your
BLACK+DECKER dealer :- (cat no. FSMP20-XJ).
u Place a cleaning pad (7) on the floor with the velcro 'loop'
side facing up.
u Lightly press the steam mop down onto the cleaning pad
(7).
Caution: Always place your steam mop with the handle (9)
supported in the upright position when stationary and make
sure the steam mop is turned off when not in use.
u Replace the water tank access tab.
Note! Ensure the water tank access tab is firmly secured.
Note! Do not use chemical cleaners with your steam mop
water tank.
Use
Important! This unit will kill 99.9% of bacteria and germs
when used in accordance with the instructions in this manual
and with the micro fibre pad fitted and a continuous run time
of 90 seconds.
Caution! Always wear suitable shoes when changing the
cleaning pad on your steam mop. Do not wear slippers or
open toed footwear.
u Return the handle (9) to the upright position and turn the
steam mop 'OFF'.
u Wait until the steam mop cools down (approximately 5
minutes).
u Lift the steam mop away from the cleaning pad freeing it
from the velcro fastening.
Caution! Always place your steam mop with the handle (9)
supported in the upright position when stationary and make
sure the steam mop is turned off when not in use.
Switching on and off
u To switch the appliance on, press the ON/Off button (1).
It takes approximately 15 seconds for the steam mop to
heat up.
u Press the steam operation button (2). This will operate the
pump and the unit will begin to produce steam.
u To stop steam generation, turn the steam operation button
(2) to off. This will maintain power to the boiler for quicker
start up.
u To switch the appliance off, press the ON/Off button (1).
Caution! Never leave the steam mop in one spot on any
surface for any period of time.
Always place the steam mop with the handle (9) supported in
the upright position when stationary and make sure the steam
mop is turned off when not in use.
Caution! Always empty the steam mop after use.
Note! When first filled or after running dry, it can take up to 45
seconds for steam to be produced.
Using as a hand held unit
Hints for optimum use
Removing a cleaning pad
Disonnect the hand held unit from the steam head by
pushing the connection button (5a) figure D.
u Remove the handle (9) from the hand held unit by pushing
the handle connector button (8) figure C.
u
Fitting accessories (Fig. F)
Fit the accessorie adaptor (13) into the main body of the
unit ensuring the button (13a) clicks into the relevant
opening.
u Attach the required accessorie to the accessorie adaptor
(13) and twist clockwise to lock into place.
u
Filling the water tank (Fig. G)
Note! Fill the water tank with clean tap water.
Note! In areas of hard water, the use of de-ionised water is
recommended.
u Open the water tank access tab (3).
u Fill the water tank (4) with water.
Warning! Your water tank has a 380ml capacity. Do not over
fill the tank.
6
General
Caution: Never use the steam mop without first attaching a
cleaning pad.
u Always vacuum or sweep the floor before using the steam
mop.
u The easiest way to use the appliance is to tilt the handle
to a 45º angle and clean slowly, covering a small area at a
time.
u Do not use chemical cleaners with your steam mop. To
remove stubborn stains from vinyl or linoleum floors, you
can pre-treat with a mild detergent and some water before
using the steam mop.
Steam Cleaning
Place a cleaning pad (7) on the floor with the velcro 'loop'
side facing up.
u Lightly press the steam mop down onto the cleaning pad
(7).
u Connect the steam mop to the mains.
u Press the ON/OFF button (1). It takes approximately 15
seconds for the steam mop to heat up.
u
(Original instructions)
Press the steam operate button (2). After a few seconds,
steam will start to come out of the steam head.
Note! When first filled or after running dry, it can take up to 45
seconds for steam to be produced.
u It takes a few seconds for steam to enter the cleaning pad.
The steam mop will now glide easily over the surface to be
sanitized/cleaned.
u Push and pull the steam mop slowly across the surface to
thoroughly steam clean each section.
u When you have finished using the steam mop, return
the handle (9) to the upright position, making sure that it
is supported and turn it 'OFF'. Wait until the steam mop
cools down (approximately five minutes).
Caution! It is important to monitor the water level in the water
tank (4). To refill the water tank and continue to sanitize/
clean stand the mop upright making sure that the handle is
supported and turn the steam mop 'OFF'. Unplug the unit from
the electrical wall outlet, refill the water tank (4).
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (9) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
u
After use (Fig. H)
Turn the steam mop 'OFF'. turn the steam operation
button (2) to off and then press the ON/OFF button (1).
u Wait until the steam mop cools down.
u Unplug the steam mop from the electrical wall outlet.
u Empty the water tank.
u remove the cleaning pad (7) and wash it ready for next
use.
u Wrap the power supply cable around the tidy hook (10).
u
ENGLISH
Problem
Step
Possible solution
The steam mop is not
turning on
1.
Check the unit is
plugged in at the wall
socket.
2.
Check the unit is
switched on using the
ON/OFF switch (1)
3.
Check the fuse in the
plug.
4.
Check the water tank
(4) is full .
NOTE: When first filled
or after running dry it
can take up to 45
seconds for steam to
be produced.
5.
Check the steam
generation button is in
the ON position (2).
6.
The steamer is
equipped with a
thermostat and a
thermal cut-out. If for
any reason the steamer
overheats it will switch
off. If this happens turn
off and unplug the
steamer, allow to cool
for 2 to 4 hours and
re-try.
7.
Refer to the assembly
chapter of the manual
for correct fitting of
parts and
accessories.
The steam mop is not
producing steam
Where can I get
further information/
accessories for my
steam mop
Technical Data
FSMH13E5
FSMH13E10
Voltage
Vac
230
230
Power
W
1300
1300
Tank
Capacity
ml
380
380
Weight
kg
2.8
1.8
Troubleshooting
If your appliance seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local BLACK+DECKER repair agent.
7
Australia
New Zealand
Black & Decker (Australia) Pty. Ltd.
20 Fletcher Road, Mooroolbark,
Victoria, 3138
Tel. Fax 03-8720 5100
03-9727 5940
Black & Decker
5 Te Apunga Place
Mt Wellington
Aukland 1060
Tel. Fax +64 9 259 1133
+64 9 259 1122
United Kingdom &
Black & Decker
Tel. 01753 511234
Republic Of Ireland
210 Bath Road
Fax 01753 512365
www.blackanddecker.co.uk Slough, Berkshire SL1 3YD
emeaservice@sbdinc.com
N544384 REV-01
08/2017
Download PDF

advertising