DCS331 | DeWalt DCS331 CORDLESS JIGSAW Type 3 instruction manual

DCS331
DCS332
English
6
简体中文
17
Copyright DeWALT
2
Figure 1
p
d
a
q
c
e
b
f
g
h
Figure 2
i
j
1
Figure 3
Figure 4
a
b
r
Figure 6
Figure 5
l
d
k
d
2
e
b
Figure 7
f
g
Figure 9
Figure 8
i
h
3
Figure 10
그림 10
Figure 11
그림 11
g
m
g
n
j
j
Figure 12
그림 12
4
Figure 13
그림 13
Figure 14
그림 14
5
E N GLI SH
CORDLESS JIGSAW
DCS331, DCS332
Congratulations!
You have chosen a DeWALT tool. Years of
experience, thorough product development and
innovation make DeWALT one of the most reliable
partners for professional power tool users.
Technical Data
DCS332 DCS331
Voltage
VDC
14.418
Battery Type Li-Ion
Li-Ion
No-load speed
min-1
0–2500 0–3000
Stroke length
mm
26
26
Cutting depth in:
– wood
mm
135
135
– aluminum mm
25
25
– steel
mm
10
10
Bevel angle adjustment (l/r) ˚
0–45
0–45
Weight (without
battery pack)
kg
2.4
2.4
Battery pack DCB140DCB141DCB142
Battery type
Li-Ion
Li-IonLi-Ion
VoltageVDC14.4 14.4 14.4
CapacityAh3.0 1.5 4.0
Weight
kg0.53 0.30 0.54
Battery pack DCB180DCB181DCB182
Battery type
Li-Ion
Li-IonLi-Ion
VoltageVDC18 18 18
CapacityAh3.0 1.5 4.0
Weight
kg0.64 0.35 0.61
Battery pack
DCB183 DCB184
Battery type
Li-Ion
Li-Ion
VoltageVDC18 18
CapacityAh2.0 5.0
Weight
kg0.4 0.62
ChargerDCB105
Mains voltage
VAC 220-240 V
Battery type
Li-Ion
Approx. charging min
30
55
time
(1.5 Ah
(3.0 Ah
battery packs) battery packs)
70
(4.0 Ah battery packs)
Weight
kg0.49
ChargerDCB115
Mains voltage
VAC 220-240 V
Battery type
Li-Ion
Approx. charging min
25
30
time
(1.3 Ah
(1.5 Ah
battery packs) battery packs)
40 55
(2.0 Ah
(3.0 Ah
battery packs) battery packs)
70 90
(4.0 Ah
(5.0 Ah
battery packs) battery packs)
Weight
kg0.5
Definitions: Safety Guidelines
The definitions below describe the level of severity
for each signal word. Please read the manual and
pay attention to these symbols.
DANGER: Indicates an imminently
hazardous situation which, if not
avoided, will result in death or
serious injury.
WARNING: Indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
NOTICE: Indicates a practice not
related to personal injury which, if
not avoided, may result in property
damage.
6
E NG L I S H
Denotes risk of electric shock.
Denotes risk of fire.
WARNING: To reduce the risk of injury,
read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings
and instructions Failure to follow the
warnings and instructions may result in
electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or batteryoperated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f)
If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your finger
on the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
7
E N GLI SH
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive
safety measures reduce the risk of starting
the power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc., in accordance with these
instructions taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified
by the manufacturer. A charger that is
suitable for one type of battery pack may
create a risk of fire when used with another
battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any
other battery packs may create a risk of
injury and fire.
c) When battery pack is not in use, keep it
away from other metal objects like paper
clips, coins, keys, nails, screws or other
small metal objects that can make a
connection from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery, avoid contact.
If contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6) SERVICE
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Additional Safety Rules for Jigsaws
•Hold power tool by insulated gripping
surfaces, when performing an operation
where the cutting accessory may contact
hidden wiring. Cutting accessory contacting a
“live” wire may make exposed metal parts of the
power tool “live” and could give the operator an
electric shock.
•Use clamps or another practical way to
secure and support the workpiece to a
stable platform. Holding the work by hand or
against your body leaves it unstable and may
lead to loss of control.
•Allow the motor to come to a complete
stop before withdrawing the blade from
the kerf (the slot created by cutting).
A moving blade may impact the workpiece
causing a broken blade, workpiece damage or
loss of control and possible personal injury.
•Keep handles dry, clean, free from oil and
grease. This will enable better control of the
tool.
•Keep blades sharp. Dull blades may cause
the saw to swerve or stall under pressure.
• Clean out your tool often, especially after
heavy use. Dust and grit containing metal
particles often accumulate on interior surfaces
and could create an electric shock hazard.
•Do not operate this tool for long periods of
time. Vibration caused by the operating action
of this tool may cause permanent injury to
fingers, hands, and arms. Use gloves to provide
extra cushion, take frequent rest periods, and
limit daily time of use.
Residual Risks
• In spite of the application of the relevant
safety regulations and the implementation of
safety devices, certain residual risks cannot be
avoided.
These are:
– Impairment of hearing.
– Risk of accidents caused by the uncovered
parts of the moving saw blade.
– Risk of injury when changing the blade.
– Risk of dust inhalation from materials that
when cut, can be harmful.
8
E NG L I S H
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
• These chargers are not intended for
any uses other than charging DeWALT
rechargeable batteries. Any other uses
may result in risk of fire, electric shock or
electrocution.
• Do not expose charger to rain or snow.
DATE CODE POSITION
The Date Code, which also includes the year of
manufacture, is printed into the housing surface that
forms the mounting joint between tool and battery.
Example:
2012 XX XX
Year of Manufacture
Important Safety Instructions for All
Battery Chargers
SAVE THESE INSTRUCTIONS: This manual
contains important safety and operating instruc­tions
for the DCB105 and DCB115 battery charger.
• Before using the charger, read all instructions
and cautionary markings on charger, battery
pack and product using the battery pack.
• Pull by plug rather than cord when
disconnecting charger. This will reduce risk
of damage to electric plug and cord.
• Make sure that cord is located so that it will
not be stepped on, tripped over or otherwise
subjected to damage or stress.
• Do not use an extension cord unless it
is absolutely necessary. Use of improper
extension cord could result in risk of fire,
electric shock or electrocution.
• When operating a charger outdoors, always
provide a dry location and use an extension
cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of
electric shock.
• Do not block the ventilation slots on the
charger. The ventilation slots are located
on the top and sides of the charger. Place
the charger in a position away from any heat
source.
WARNING: Shock hazard. Do not allow
any liquid to get inside charger. Electric
shock may result.
CAUTION: Burn hazard. To reduce
the risk of injury, charge only DeWALT
rechargeable battery packs. Other types
of batteries may overheat and burst
resulting in personal injury and property
damage.
• Do not operate charger with damaged cord
or plug — have them replaced immediately.
CAUTION: Children should be
supervised to ensure that they do not
play with the appliance.
• Do not disassemble the charger; take it to
an authorised service centre when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock, electrocution or
fire.
NOTICE: Under certain conditions, with
the charger plugged in to the power
supply, the exposed charging contacts
inside the charger can be shorted by
foreign material. Foreign materials of
a conductive nature such as, but not
limited to, steel wool, aluminum foil or
any buildup of metallic particles should
be kept away from charger cavities.
Always unplug the charger from the
power supply when there is no battery
pack in the cavity. Unplug charger
before attempting to clean.
• DO NOT attempt to charge the battery pack
with any chargers other than the ones in
this manual. The charger and battery pack are
specifically designed to work together.
•Do not operate charger if it has received
a sharp blow, been dropped or otherwise
damaged in any way. Take it to an authorised
service centre.
• In case of damaged power supply cord the
supply cord must be replaced immediately by
the manufacturer, its service agent or similar
qualified person to prevent any hazard.
• Disconnect the charger from the outlet
before attempting any cleaning. This will
reduce the risk of electric shock. Removing
the battery pack will not reduce this risk.
•NEVER attempt to connect 2 chargers together.
• The charger is designed to operate on
standard 220-240 V household electrical
power. Do not attempt to use it on any other
voltage. This does not apply to the vehicular
charger.
9
E N GLI SH
NOTE: This could also mean a problem with a
charger.
SAVE THESE INSTRUCTIONS
Chargers
The DCB105 and DCB115 charger accepts 10.8
V, 14.4 V and 18 V Li-Ion (DCB121, DCB123,
DCB140, DCB141, DCB142, DCB180, DCB181
DCB182, DCB183 and DCB184) battery packs
This charger requires no adjustment and is designed
to be as easy as possible to operate.
Charging Procedure (fig. 3)
1.Plug the charger into an appropriate 220-240 V
outlet before inserting the battery pack.
2.Insert the battery pack (b) into the charger,
making sure the pack is fully seated in the
charger. The red (charging) light will blink
continuously indicating that the charging
process has started.
3.The completion of charge will be indicated by
the red light remaining ON continuously. The
pack is fully charged and may be used at this
time or left in the charger.
NOTE: To ensure maximum performance and life of
Li-Ion batteries, charge the battery pack fully before
first use.
If the charger indicates a problem, take the charger
and battery pack to be tested at an authorised
service centre.
Hot/Cold Pack Delay
When the charger detects a battery that is too hot
or too cold, it automatically starts a hot/cold pack
delay, suspending charging until the battery has
reached an appropriate temperature. The charger
then automatically switches to the pack charging
mode. This feature ensures maximum battery life.
XR Li-Ion tools are designed with an Electronic
Protection System that will protect the battery
against overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic
Protection System engages. If this occurs, place the
Li-Ion battery on the charger until it is fully charged.
A cold battery pack will charge at about half the rate
of a warm battery pack. The battery pack will charge
at that slower rate throughout the entire charging
cycle and will not return to maximum charge rate
even if the battery warms.
Charging Process
Important Safety Instructions for All
Battery Packs
Refer to the table below for the state of charge of
the battery pack.
When ordering replacement battery packs, be sure
to include the catalog number and voltage.
Charge indicators: DCB105
charging
–––––––––––– ––
fully charged
––––––––––––––––––––
hot/cold pack delay
–––• –––• –––• –––
replace battery pack
••••••••••••••
Charge indicators: DCB115
charging
––––––––––
fully charged
––––––––––––––
hot/cold pack delay*
–––– ––––––––
*DCB115: The red light will continue to blink, but
a yellow indicator light will be illuminated during
this operation. Once the battery has reached an
appropriate temperature, the yellow light will turn off
and the charger will resume the charging procedure.
The compatible charger(s) will not charge a faulty
battery pack. The charger will indicate faulty battery
by refusing to light or by displaying problem pack or
charger blink pattern.
10
The battery pack is not fully charged out of the
carton. Before using the battery pack and charger,
read the safety instructions below and then follow
the charging procedures outlined.
READ ALL INSTRUCTIONS
• Do not charge or use the battery pack
in explosive atmospheres, such as in the
presence of flammable liquids, gases or
dust. Inserting or removing the battery pack
from the charger may ignite the dust or fumes.
• Never force the battery pack into charger.
Do not modify the battery pack in any way
to fit into a non-compatible charger as
battery pack may rupture causing serious
personal injury.
• Charge the battery packs only in designated
DeWALT chargers.
• DO NOT splash or immerse in water or other
liquids.
• Do not store or use the tool and battery
pack in locations where the temperature
may reach or exceed 40 ˚C (105 ˚F) (such as
outside sheds or metal buildings in summer).
E NG L I S H
• For best results, make sure the battery pack is
fully charged before use.
WARNING: Never attempt to open
the battery pack for any reason. If
the battery pack case is cracked or
damaged, do not insert it into the
charger. Do not crush, drop or damage
battery pack. Do not use a battery
pack or charger that has received a
sharp blow, been dropped, run over
or damaged in any way (e.g., pierced
with a nail, hit with a hammer, stepped
on). Electric shock or electrocution may
result. Damaged battery packs should
be returned to the service centre for
recycling.
CAUTION: When not in use, place
tool on its side on a stable surface
where it will not cause a tripping or
falling hazard. Some tools with large
battery packs will stand upright on the
battery pack but may be easily knocked
over.
Storage Recommendations
1.The best storage place is one that is cool and
dry away from direct sunlight and excess heat
or cold. For optimum battery performance and
life, store battery packs at room temperature
when not in use.
2.For long storage, it is recommended to store a
fully charged battery pack in a cool, dry place
out of the charger for optimal results.
NOTE: Battery packs should not be stored
completely depleted of charge. The battery pack will
need to be recharged before use.
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual,
the labels on the charger and the battery pack show
the following pictographs:
Read instruction manual before use.
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION
(Li-Ion)
Charging.
• Do not incinerate the battery pack even if it
is severely damaged or is completely worn
out. The battery pack can explode in a fire.
Toxic fumes and materials are created when
lithium ion battery packs are burned.
• If battery contents come into contact with
the skin, immediately wash the area with
mild soap and water. If the battery liquid gets
into the eye, rinse water over the open eye for
15 minutes or until irritation ceases. If medical
attention is needed, the battery electrolyte
is composed of a mixture of liquid organic
carbonates and lithium salts.
• Contents of opened battery cells may cause
respiratory irritation. Provide fresh air. If
symptoms persists, seek medical attention.
WARNING: Burn hazard. Battery liquid
may be flammable if exposed to spark
or flame.
Battery Pack
Fully charged.
Hot/cold pack delay.
x
Problem pack or charger.
Problem powerline.
Do not probe with conductive objects.
Do not charge damaged battery packs.
Charge DeWALT battery packs only with
designated DeWALT chargers. Charging
battery packs other than the designated
DeWALT batteries with a DeWALT charger
may make them burst or lead to other
dangerous situations (see Technical
Data).
BATTERY TYPE
The DCS332 operates on an 14.4 volt battery pack.
Do not expose to water.
The DCS331 operates on an 18 volt battery pack.
The DCB140, DCB141, DCB142, DCB180,
DCB181 DCB182, DCB183 or DCB184 battery
packs may be used. Refer to Technical Data for
more information.
Have defective cords replaced
immediately.
Charge only between 4 °C and 40 °C.
11
E N GLI SH
Discard the battery pack with due care for
the environment.
p. Main Handle
q. Top Handle
INTENDED USE
Charges Li-Ion battery packs.
Your DCS332 and DCS331 jig saws are designed
for professional cutting of wood, steel, aluminium,
plastic and ceramic material at various work sites
(i.e., construction sites).
See Technical Data for charging time.
DO NOT use under wet conditions or in presence of
flammable liquids or gases.
Do not incinerate the battery pack.
Only for indoor use.
Package Contents
1 Cordless jigsaw
1 Anti-scratch shoe cover
1 Dust port
2Batteries
1Charger
1 Instruction manual
NOTE: Battery packs, chargers and kitboxes are not
included with N-models.
• Check for damage to the tool, parts or
accessories which may have occurred during
transport.
• Take the time to thoroughly read and
understand this manual prior to operation.
These heavy-duty jigsaws are professional power
tools.
DO NOT let children come into contact with the
tool. Supervision is required when inexperienced
operators use this tool.
• This product is not intended for use by persons
(including children) suffering from diminished
physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are
supervised by a person responsible for their
safety. Children should never be left alone with
this product.
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the battery pack
voltage corresponds to the voltage on the rating
plate. Also make sure that the voltage of your
charger corresponds to that of your mains.
Your DeWALT charger is double insulated
in accordance with IEC 60335; therefore
no earth wire is required.
Description (fig. 1, 2, 6, 10, 11)
WARNING: Never modify the power
tool or any part of it. Damage or
personal injury could result.
a. Battery release button
b. Battery pack
c. Trigger switch
d. Trigger lock button
e. Blade release lever
f. Bevel lever
g. Shoe
h. Orbital action lever
i. Dust blower control
j. Anti-scratch shoe cover
k. Clamp Mechanism
l. Guide Roller
m. Rear Tab
n. Anti-Splinter Insert
12
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
DeWALT service organisation.
Using an Extension Cable
An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see Technical Data). The minimum conductor size
is 1 mm2; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENT
WARNING: To reduce the risk of
serious personal injury, depress the
trigger lock button and disconnect
battery pack before making any
adjustments or removing/installing
attachments or accessories. An
accidental start-up can cause injury.
E NG L I S H
WARNING: Use only DeWALT battery
packs and chargers.
Inserting and Removing the
Battery Pack from the Tool (fig. 4)
NOTE: For best results, make sure your battery
pack is fully charged. The light will shut off without
warning when the battery is fully discharged.
TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE
1.Align the battery pack (b) with the rails inside the
tool’s handle (fig. 4).
2.Insert the T-shank blade into the clamp
mechanism (k) while guiding the back of the
blade into the groove of the guide rollers (l).
3.The T-shank should be completely inside the
clamp mechanism as shown in Figure 6.
4.Release the keyless blade release lever.
TO REMOVE A BLADE
CAUTION: Do not touch used blades,
they may be hot. Personal injury may
result.
1.Lift the keyless blade release lever (e).
2.Slide it into the handle until the battery pack is
firmly seated in the tool and ensure that it does
not disengage.
2.With a slight shake the blade will drop out.
TO REMOVE THE BATTERY PACK FROM THE TOOL
To unlock the shoe, pull the keyless bevel lever (f)
to the side.
1.Press the battery release button (a) and firmly
pull the battery pack out of the tool handle.
2.Insert battery pack into the charger as
described in the charger section of this manual.
Beveling the Shoe (fig. 7)
To lock the shoe, push the keyless bevel lever
back under the body of the jigsaw.
TO BEVEL THE SHOE
FUEL GAUGE BATTERY PACKS (FIG. 4)
1.Unlock the shoe.
Some DeWALT battery packs include a fuel gauge
which consists of three green LED lights that
indicate the level of charge remaining in the battery
pack.
2.Slide the shoe (g) forward to release it from the
0° positive stop position.
To actuate the fuel gauge, press and hold the fuel
gauge button (r). A combination of the three green
LED lights will illuminate designating the level of
charge left. When the level of charge in the battery
is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
NOTE: The fuel gauge is only an indication of the
charge left on the battery pack. It does not indicate
tool functionality and is subject to variation based
on product components, temperature and end-user
application.
Blade Installation and Removal
(fig. 6)
TO INSTALL A BLADE
NOTE: This jig saw uses only T-shank jig saw
blades.
NOTE: The DT2074 flush cutting blade is for use
with DeWALT DCS331, DCS332, DW331 and
DC330 jig saws only.
NOTE: When installing flush cutting blades
(DT2074), the anti-splinter insert must be removed
and the shoe must to be in the 0° positive stop
position.
1.Lift the keyless blade release lever (e) as shown
in figure 6.
3.The shoe can be beveled to the left or to the
right and has detents at 15°, 30° and 45°. The
shoe can be manually stopped at any degree
between 0° and 45°.
4.Once the desired bevel angle is achieved, lock
the shoe into place.
TO SET SHOE BACK TO 0°
1.Unlock the shoe.
2.Rotate the shoe back to 0°.
3.Slide the shoe back into the 0° positive stop
position.
4.Lock the shoe.
Cutting Action – Orbital or Straight
(fig. 8)
This jig saw is equipped with four cutting actions,
three orbital and one straight. Orbital action has a
more aggressive blade motion and is designed for
cutting in soft materials like wood or plastic. Orbital
action provides a faster cut, but with a less smooth
cut across the material. In orbital action, the blade
moves forward during the cutting stroke in addition
to the up and down motion.
NOTE: Metal or hardwoods should never be cut in
orbital action.
To adjust the cutting action, move the orbital
action lever (h) between the four cutting positions: 0,
13
E N GLI SH
1, 2, and 3. Position 0 is straight cutting. Positions
1, 2, and 3 are orbital cutting. The aggressiveness of
the cut increase as the lever is adjusted from one to
three, with three being the most aggressive cut.
Dust Blower (fig. 9)
The dust blower helps clear the cutting area of
debris created from the blade.
WARNING: Always wear proper
personal hearing protection. Under
some conditions and duration of use,
noise from this product may contribute
to hearing loss.
Instructions for Use
WARNING:
NOTE: When cutting metal, turn the dust blower off
so cutting fluids are not blown away from the blade.
• Always observe the safety instructions and
applicable regulations.
To turn the dust blower on, slide the dust blower
control (i) all the way to the top.
• Make sure your workpiece is well secured.
Remove nails, screws and other fasteners that
may damage the blade.
To turn the dust blower off, slide the dust blower
control all the way to the bottom.
Removeable Anti-Scratch Shoe
Cover (fig. 10)
The anti-scratch shoe cover (j) should be used
when cutting surfaces that scratch easily, such as
laminate, veneer or paint.
To attach anti-scratch shoe cover (j), place the front
of the aluminum shoe (g) into the front of the antiscratch shoe cover and lower the jig saw. The antiscratch shoe cover will click securely onto the rear of
aluminum shoe.
To remove anti-scratch shoe cover, grasp the antiscratch shoe cover from the bottom; holding onto
the two rear tabs (m) remove the anti-scratch shoe
cover.
Anti-Splinter Insert (fig. 11)
NOTE: Do not use the anti-splinter insert with the
flush cutting blade.
The anti-splinter insert (n) should be used when
trying to minimize tear-out, especially when cutting
veneer, laminate, or finished surfaces, such as paint.
The anti-splinter insert should be installed into the
anti-scratch shoe cover (j). If the no-mar cover is not
used, install anti-splinter insert into shoe (g).
Prior to Operation
• Make sure your battery pack is (fully) charged.
OPERATION
14
WARNING: To reduce the risk of
serious personal injury, depress the
trigger lock button and disconnect
battery pack before making any
adjustments or removing/installing
attachments or accessories. An
accidental start-up can cause injury.
• Check that there is sufficient space for the blade
underneath the workpiece. Do not cut materials
that are thicker than the maximum cutting
depth.
• Use sharp saw blades only. Damaged or bent
saw blades must be removed immediately.
• Never run your tool without a saw blade.
• For optimal results, move the tool smoothly
and constantly over the workpiece. Do not
exert lateral pressure on the saw blade. Keep
the shoe flat on the workpiece. When sawing
curves, circles or other round shapes, push the
tool gently forward.
• Wait until the tool has come to a standstill
before removing the saw blade from the
workpiece. After sawing the blade may be very
hot. Do not touch.
Proper Hand Position (fig. 1, 14)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the top
handle (q), with the other hand on the main handle
(p).
Trigger Switch (fig. 1)
To start the jig saw, squeeze the trigger switch (c).
To slow and stop the jig saw, release the trigger
switch.
VARIABLE SPEED (FIG. 5)
As the trigger switch is pressed in, the strokesper-minute continue to increase, but not to exceed
E NG L I S H
the maximum speed of the tool. As the trigger is
released, the blade strokes-per-minute reduce.
The trigger lock button (d) should be depressed
whenever the tool is not in use to eliminate the
chance of accidental starting.
Cutting
WARNING: The jig saw should not be
operated with the shoe removed or
serious personal injury may result.
POCKET CUTTING (FIG. 12)
A pocket cut is an easy method of making an inside
cut. The saw can be inserted directly into a panel
or board without first drilling a lead or pilot hole. In
pocket cutting, measure the surface to be cut and
mark clearly with a pencil. Next tip the saw forward
until the front end of the shoe sits firmly on the work
surface and the blade clears the work through its
full stroke. Switch the tool on and allow it to attain
maximum speed. Grip the saw firmly and lower the
back edge of tool slowly until the blade reaches
its complete depth. Hold the shoe flat against the
wood and begin cutting. Do not remove blade from
cut while it is still moving. Blade must come to a
complete stop.
FLUSH CUTTING (FIG. 13)
A flush cut is necessary when finishing off cuts up
to a wall or an obstacle, such as back-splash. One
of the easiest ways to accomplish the flush cut is to
use a flush cutting blade (DT2074). The flush cutting
blade provides the reach necessary to cut right up
to the front edge of the jig saw shoe. Remove the
anti-splinter insert and return the shoe to the 0°
positive stop position before installing and using the
flush cutting blade. For the best cut quality the flush
cutting blade should be used in the 0 or 1 orbital
position. The flush cutting blade should not be used
to start the cut because the flush cutting blade
prevents the shoe from being supported by the
work surface. Use wood cutting practices explained
below.
WOOD CUTTING
Support the workpiece adequately at all times. Use
the higher speed setting for cutting wood. Do not
attempt to turn the tool on when blade is against
material to be cut. This could stall the motor. Place
the front of shoe on the material to be cut and
hold the jig saw shoe firmly against the wood while
cutting. Don’t force the tool; let the blade cut at its
own speed. When the cut is complete, turn the jig
saw off. Let blade come to a complete stop and
then lay the saw aside before loosening the work.
METAL CUTTING
In cutting thin gauge sheet metals, it is best to clamp
wood to the bottom of sheet metal; this will insure
a clean cut without the risk of vibration or tearing
of metal. Always remember to use a finer blade
for ferrous metals (for those that have a high iron
content); and use a coarser blade for non-ferrous
metals (those that do not have an iron content).
Use a high speed setting for cutting soft metals
(aluminum, copper, brass, mild steel, galvanized.
pipe, conduit sheet metal, etc.). Use lower speed
to cut plastics, tile, laminate, hard metals, and cast
iron.
MAINTENANCE
Your DeWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
serious personal injury, depress the
trigger lock button and disconnect
battery pack before making any
adjustments or removing/installing
attachments or accessories. An
accidental start-up can cause injury.
The charger and battery pack are not serviceable.
There are no serviceable parts inside.
Lubrication
LUBRICATING THE GUIDE ROLLER (FIG. 6)
• Apply a drop of oil to the guide roller (l) at
regular intervals to prevent jamming.
Cleaning
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
15
E N GLI SH
tool; never immerse any part of the tool
into a liquid.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect
the charger from the AC outlet before
cleaning. Dirt and grease may be
removed from the exterior of the charger
using a cloth or soft non-metallic brush.
Do not use water or any cleaning
solutions.
Optional Accessories
WARNING: Since accessories, other
than those offered by DeWALT, have
not been tested with this product, use
of such accessories with this tool could
be hazardous. To reduce the risk of
injury, only DeWALT, recommended
accessories should be used with this
product.
Consult your dealer for further information on the
appropriate accessories.
These include:
– DE3241 Parallel guide
– DE3242 Trammel bar
– 581281-00 Dust extraction adapter
– 581239-01 Dust extraction shroud
– 402140-00 Anti-splinter shoe insert
– 581268-00 Anti-scratch shoe cover
Protecting the Environment
Separate collection. This product must
not be disposed of with normal
household waste.
Should you find one day that your DeWALT product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.
Separate collection of used products
and packaging allows materials to be
recycled and used again. Re-use of
recycled materials helps prevent
environmental pollution and reduces
the demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at
municipal waste sites or by the retailer when you
purchase a new product.
16
DeWALT provides a facility for the collection and
recycling of DeWALT products once they have
reached the end of their working life. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
You can check the location of your nearest
authorised repair agent by contacting your local
DeWALT office at the address indicated in this
manual. Alternatively, a list of authorised DeWALT
repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when
it fails to produce sufficient power on jobs which
were easily done before. At the end of its technical
life, discard it with due care for our environment:
• Run the battery pack down completely, then
remove it from the tool.
• Li-Ion cells are recyclable. Take them to your
dealer or a local recycling station. The collected
battery packs will be recycled or disposed of
properly.
简体中文
18V锂电充电式曲线锯
DCS331,DCS332
祝贺您!
感谢您选择得伟工具。凭借多年的经验以及全面的产
品开发与创新,得伟已经成为专业电动工具使用者最
值得信赖的伙伴之一。
如果你对这款或者任何的得伟工具有任何的疑问或
者意见,请致电:800-820-4221或者 400-620-4221
技术参数
DCS332 DCS331
电压
伏特(直流)
14.418
电池类型锂离子 锂离子
空载转速
转/分
0–25000–3000
冲程长度
毫米
2626
锯切深度:
– 木材
毫米
135135
– 铝材
毫米
2525
– 钢材
毫米
1010
坡口调节范围 (l/r) 0–45
0–45
重量(不含
电池组)
千克
2.42.4
电池组
类型
电压
容量
重量
DCB140 DCB141 DCB142
锂离子 锂离子 锂离子
伏特 14.4
14.4
14.4
安时 3.0
1.5
4.0
千克 0.53
0.30
0.54
电池组
Battery type
电压
容量
重量
DCB180 DCB181 DCB182
锂离子 锂离子 锂离子
伏特
18
18
18
安时 3.0
1.5
4.0
千克 0.64
0.35
0.61
电池组
类型
电压
容量
重量
DCB183 DCB184
锂离子 锂离子
伏特
18
18
安时 2.0
5.0
千克 0.4
0.62
充电器
电压
伏特
类型
电池组的大约 分钟
充电时间
重量
千克
DCB105
220
锂离子
25
30
(1.3 安时 (1.5 安时 电池组) 电池组)
40
55
(2.0 安时 (3.0 安时 电池组) 电池组)
70
90
(4.0 安时 (5.0 安时 电池组) 电池组)
0.49
充电器
DCB115
电压
伏特
220
类型
锂离子
电池组的大约 分钟
22
22
充电时间
(1.3 安时 (1.5 安时 电池组) 电池组)
30
45
(2.0 安时 (3.0 安时 电池组) 电池组)
60
70
(4.0 安时 (5.0 安时 电池组) 电池组)
重量
千克
0.5
类型
锂离子
电池组的大约
分钟
22
45
充电时间
(1.5 安时) (3.0 安时) 60
(4.0 安时)
重量
kg
0.5
定义:安全守则
下列定义描述了各标志术语的严重程度。请仔细阅
读本手册,并注意这些标志。
危险:表示紧急危险情况,如果不加以
避免,将导致死亡或严重伤害。
警告:表示存在潜在的危险情况,如
果不加以避免,可能导致死亡或严重伤
害。
17
简体中文
警示:表示存在潜在危险情况,如果不
加以避免,可能导致轻度或中度伤害。
注意:表示存在不涉及人身伤害的情
边或运动部件。受损或缠绕的软线会增加电击
危险。
5)当在户外使用电动工具时,使用适合户外使用
况,如果不加以避免,可能导致财产损
的外接软线。适合户外使用的软线将减少电击
失。
危险。
表示存在触电风险。
表示存在火灾风险。
6)如果在潮湿环境下操作电动工具是不可避免
的,应使用剩余电流动作保护器(RCD)。使
警告:为降低伤害风险,请阅读使用手
册。
用RCD可减小电击危险。
c) 人身安全
1)保持警觉,当操作电动工具时关注所从事的操
电动工具通用安全警告 作并保持清醒。当你感到疲倦,或在有药物、
作电动工具时瞬间的疏忽会导致严重人身伤
警告!阅读所有警告和所有说明。不
遵照以下警告和说明会导致电击、着火
和/或严重伤害。
保存所有警告和说明书以备查阅。
酒精或治疗反应时,不要操作电动工具。在操
害。
2)使用个人防护装置。始终佩戴护目镜。安全装
置,诸如适当条件下使用防尘面具、防滑安全
在所有下列的警告中术语“电动工具”指市电驱动
鞋、安全帽、听力防护等装置能减少人身伤
(有线)电动工具或电池驱动(无线)电动工具。
害。
a) 工作场地的安全
1)保持工作场地清洁和明亮。混乱和黑暗的场地
会引发事故。
2)不要在易爆环境,如有易燃液体、气体或粉尘
的环境下操作电动工具。电动工具产生的火花
会点燃粉尘或气体。
3) 让儿童和旁观者离开后操作电动工具。注意力
不集中会使操作者失去对工具的控制。
b) 电气安全
1) 电动工具插头必须与插座相配。绝不能以任何
方式改装插头。需接地的电动工具不能使用任
何转换插头。未经改装的插头和相配的插座将
减少电击危险。
2)避免人体接触接地表面,如管道、散热片和冰
箱。如果你身体接地会增加电击危险。
3)不得将电动工具暴露在雨中或潮湿环境中。水
进入电动工具将增加电击危险。
4)不得滥用电线。绝不能用电线搬运、拉动电动
工具或拔出其插头。使电线远离热源、油、锐
3)防止意外起动。确保开关在连接电源和/或电池
组、拿起或搬运工具时处于关断位置。手指放
在已接通电源的开关上或开关处于接通时插入
插头可能会导致危险。
4) 在电动工具接通之前,拿掉所有调节钥匙或扳
手。遗留在电动工具旋转零件上的扳手或钥匙
会导致人身伤害。
5) 手不要伸展得太长。时刻注意立足点和身体
平衡。这样在意外情况下能很好地控制电动工
具。
6)着装适当。不要穿宽松衣服或佩戴饰品。让
你的衣服、手套和头发远离运动部件。宽松衣
服、佩饰或长发可能会卷入运动部件中。
7)如果提供了与排屑、集尘设备连接用的装置,
要确保他们连接完好且使用得当。使用这些装
置可减少尘屑引起的危险。
d) 电动工具使用和注意事项
1)不要滥用电动工具,根据用途使用适当的电动
工具。选用适当设计的电动工具会使你工作更
有效、更安全。
18
简体中文
2)如果开关不能接通或关断工具电源,则不能使
用该电动工具。不能用开关来控制的电动工具
是危险的且必须进行修理。
3)在进行任何调节、更换附件或贮存电动工具之
前,必须从电源上拔掉插头和/或使电池盒与
工具脱开。这种防护性措施将减少工具意外起
动的危险。
4) 将闲置不用的电动工具贮存在儿童所及范围之
外,并且不要让不熟悉电动工具或对这些说明
不了解的人操作电动工具。电动工具在未经培
训的用户手中是危险的。
5)保养电动工具。检查运动件是否调整到位或卡
住,检查零件破损情况和影响电动工具运行的
其他状况。如有损坏,电动工具应在使用前修
理好。许多事故由维护不良的电动工具引发。
6)保持切削刀具锋利和清洁。保养良好的有锋利
切削刃的刀具不易卡住而且容易控制。
7)按照使用说明书,考虑作业条件和进行的作业
来使用电动工具、附件和工具的刀头等。将电
动工具用于那些与其用途不符的操作可能会导
致危险。
e) 电池式工具使用和注意事项:
1)只用制造商规定的充电器充电。将适用于某种
电池盒的充电器用到其他电池盒时会发生着火
危险。
2)只有在配有专用电池盒的情况下才使用电动工
具。使用其他电池盒会发生损坏和着火危险。
3) 当电池盒不用时,将它远离其他金属物体,例
如回形针、硬币、钥匙、钉子、螺钉或其他小
金属物体,以防一端与另一端连接。电池端部
短路会引起燃烧或火灾。
4)在滥用条件下,液体会从电池中溅出,避免接
曲线锯安全细则
• 在切削附件可能触及暗线进行操作时,要通过
绝缘握持面来握持工具。切削附件碰到带电导
线会使工具外露的金属零件带电从而使操作者
受到电击。
• 使用夹具或其他可行方法来固定和支撑工件,
将其固定到稳定的平台上。用手抓住工件或
用身体抵住工件并不稳定,可能会导致工件失
控。
• 等到电机完全停止后,再将锯片从切口(锯切
产生的槽口)中抽出。运转中的锯片可能会
冲击工件,从而导致锯片折断、工件损坏或失
控,并且可能造成人身伤害。
• 保持手柄干燥、清洁、无油或油脂。这样能够
提高工具的操控性。
• 经常清洁工具,尤其是在长时间使用后。带有
金属屑的粉尘和磨粒常常会在外表面聚积,并
且可能会引起触电危险。
• 锯片保持锋利。钝的锯片会在压力下偏斜或停
止。
• 切勿长时间操作此工具。本工具运行引起的震
动可能对手指、手部和手臂造成永久伤害。使
用手套提供额外缓冲,经常停下休息,并限制
使用时间。
剩余风险
尽管遵守了相关的安全法规并采用了安全装备,某
些其他风险仍然是无法避免的。这些风险包括:
– 听力损伤。
– 飞溅颗粒造成的人身伤害风险。
– 使用时附件发热导致的灼伤风险。
触。如果意外碰到了,用水冲洗。如果液体碰
– 长时间使用引起的人身伤害风险。
到了眼睛,还要寻求医疗帮助。从电池中溅出
工具上的标识
的液体会发生腐蚀或燃烧。
工具上印有下列图形:
f) 维修
1)让专业维修人员使用相同的备件维修电动工
使用前请阅读使用手册。
具。这将保证所维修的电动工具的安全。
19
简体中文
• 确保电源线布置在不易踩踏、踢绊、拉扯或会
日期码的位置
日期码印在工具外壳上,其中还包含制造年份
受到损害或压力的位置。
• 除非绝对必要,否则请勿使用延长线。使用不
示例:
2012 XX XX
制造年份
针对所有电池充电器的重要安全
说明
正确的延长电线可能存在火灾、触电或电击风
险。
• 请勿将任何物件放在充电器上面,或是把充电
器放在可能会堵住通风槽的柔软表面,导致充
电器的内部过热。请把充电器放置在远离任何
请妥善保管好这些说明:本手册包含重要的兼容电
热源的位置。充电器外壳顶端和底端具有通风
池充电器安全和操作说明。
槽。
• 在使用充电器之前,请先阅读所有指示以及充
电器、电池组和使用电池组的产品上的警示标
警告:触电危险。请勿让任何液体渗入
坏情况,请勿使用充电器。请将损坏的充电器
充电器,否则可能会引起触电。
送到授权维修中心维修。
警示:灼伤危险。为减低人身伤害风
• 请勿自行拆卸充电器。请将需要检修或修理的
险,只可以使用 DeWALT 充电式电池充
充电器送到授权维修中心。重装不正确可能导
电。使用其它类型的电池可能会引起爆
致触电、电击或火灾风险。
裂,并导致人身伤害和损害。
即更换已损坏的充电器。
• 如果充电器受到强烈重击、掉落或出现其他损
记。
• 禁止使用电源线或插头已损坏的充电器。请立
警示:应看管好儿童,以确保他们不将
此设备当做玩具来玩。
注意:在某些情况下,充电器连接到电
源后,充电器触头可能会被异物导致短
• 必须立即将已损坏的电源线交由制造商、服务
代理或类似的合格人员进行更换以防止安全隐
患。
• 清洁前,请先断开充电器和插座的连接,以降
低触电风险。取出电池组不会降低触电风险。
路。导电的外来物件,包括但不限于研
• 切勿将两个充电器连接在一起。
磨粉尘、金属屑、钢丝绒、铝箔纸或任
• 充电器是为 220 V 的标准家用电源而设计。请
何由金属粒子组成的物件,必须远离充
勿试图在任何其他电压下使用充电器。此规则
电器范围。充电器内没有电池组时,请
不适用于车载充电器。
断开充电器与电源的连接。清洗前,务
请妥善保管好这些说明
必拔掉充电器。
• 请勿试图使用本手册指定的充电器以外的其他
充电器
任何充电器为电池组充电。充电器和电池组都
DCB105 和 DCB115 充电器可以向 10.8伏,14伏,
是专门设计的,互相配合使用。
18伏锂离子电池组(DCB140, DCB141, DCB142,
• 除了为 DeWALT 充电式电池充电以外,这些充
DCB180, DCB181 DCB182, DCB183 和 DCB184)充
电器并不能用于其它用途。否则可能会导致火
电。DeWALT 充电器无需做出任何调整,专为简易
灾、触电或电击。
操作而设计。
• 请勿将充电器暴露于雨中或雪中。
充电程序(图 3)
• 断开充电器连接时,应拔下插头,切勿拉拽电
1.插入电池组前,先将充电器的插头插到相应的
源线。这将降低损坏电插头和电线的风险。
20
电源插座上。
简体中文
2.将电池组 (f) 插入充电器。红色(充电中)指
示灯将不断闪烁,表示充电过程已经开始。
3.红色灯持续亮起表示充电完成。此时电池组已
如果发生这种情况,请将锂离子电池放在充电器
上,直至其完全充电。
冷电池组充电速率是温热的电池组充电速率的一半
完全充电,您可以使用电池组或将电池组留在
左右。电池组在整个充电周期的充电速度都会较
充电器上。
慢,即使电池升温也不会返回到最高速度。
注:为了确保锂离子电池的效能和使用寿命最大
针对所有电池组的重要安全说明
化,在首次使用电池组之前必须将其完全充电。
在订购替换电池组时,请务必提供产品目录号和电
充电程序
压。包装箱内的电池组并未完全充电。使用电池组
关于电池组的充电状态,请参阅下表。
和充电器之前,请阅读下列安全指示,然后遵循所
述的充电程序。
充电状态指示灯:DCB105
请阅读所有说明。
充电中
–––––––––––– ––
已完全充电
––––––––––––––––––––
•禁止在易爆环境中充电或使用电池组,如有易
热/冷电池组延迟 –––• –––• –––• –––
燃液体、气体或粉尘的环境。插入或取出电池
更换电池组
组时可能会点燃粉尘或烟雾。
••••••••••••••
切勿将电池组强行插入充电器。禁止以任何方
充电状态指示灯:DCB115
式改装电池组并将电池组插入不兼容的充电
充电中
––––––––––
器,这种操作可能会导致电池组破裂,造成严
已完全充电
––––––––––––––
重的人身伤害。
热/冷电池组延迟
–––– ––––––––
*DCB115:红色指示灯会继续闪烁,但黄色指示
•只使用指定的 DeWALT 充电器为电池组充电。
• 禁止把电池组浸泡在水或其他液体中,或泼洒
水或其他液体到电池组上。
灯在本次操作过程中会亮起。电池达到适当温
度后,黄色指示灯会熄灭,充电器将恢复充电程
•禁止在温度可能达到或超过 40°C(105°F)的
地方(如夏天户外的棚子或金属建筑物中)存
序。
储或使用工具和电池组。
此兼容充电器不能为故障的电池组充电。充电器指
示灯不亮或“故障的电池组或充电器”指示灯闪烁
•为达到最佳效果,请确保电池组在使用前完全
充电。
时,表示电池有故障。
注:这也可能意味着充电器有故障。如果充电器提
警告:无论任何理由,都禁止打开电
示存在故障,请将充电器和电池组送到授权的服务
池组。电池组外壳破裂或损坏时,禁
中心进行测试。
止将电池组插入充电器。请勿挤压、
热/冷电池组延迟
掉落或损坏电池组。禁止使用受过强
烈重击、掉落、碾压或以任何其他
当充电器检测到电池过热或过冷时,它会自动启动
方式(如被钉子穿破、受到锤子的重
热/冷电池延迟模式,暂停充电,直到电池达到适当
击、踩踏)受损的电池组或充电器。
的温度。然后,充电器会自动切换到电池组充电模
否则会引起触电或电击。损坏的电池
式。此功能可确保电池拥有最长的使用寿命。
XR 锂离子电池工具具有电子保护系统设计,可保
护电池免受过载、过热或过度放电之害。如果电子
保护系统处于运作状态,该工具将自动停止操作。
组应交回服务中心回收。
警示:在不使用时,请将工具放置在不
会引起人摔倒的稳定表面上。一些具
21
简体中文
有大型电池组的工具可以直立于电池组
上,但很容易被撞翻。
锂离子电池的安全说明
充电器和电池组上的标签
除了在本手册中使用的标志,充电器和电池组的标
签还包括:
•即使在电池组严重受损或完全磨损的情况下,
使用前请仔细阅读使用手册。
也请勿焚烧电池组。电池组可能会在火中爆
炸。锂离子电池组在燃烧时会释放有毒气体和
物质。
电池充电中。
•如果皮肤接触到电池内含物质,请立即用温和
肥皂和水冲洗接触的地方。如果电池液进入眼
电池完成充电。
睛,应睁开眼睛用清水冲洗至少 15 分钟或直
到刺激感消失。如果需要医疗救助,请告知医
热/冷电池组延迟。
护人员:电池电解质是由液状有机碳酸盐和锂
盐的混合物组成。
•电池里的成分可能导致呼吸道刺激。此时请保
持空气流通。如果症状仍然存在,请就医。
警告:烧伤危险。电池液如果接触到火
x
故障电池组或充电器。
故障电源线。
禁止使用导电物体碰触。
花或火焰可能会燃烧。
电池组
禁止对损坏的电池组充电。
电池类型
只使用 DeWALT 电池组。其他电池组可
能会爆炸,造成人身伤害和损害。
DCS332 使用 14.4 伏特电池组。
DCS331 使用 18 伏特电池组。
DCB140, DCB141, DCB142, DCB180, DCB181, DCB182,
DCB183 or DCB184 电池组都可以使用。更多信息,
请参阅技术参数。
禁止暴露于水中。
电线故障,请立即更换。
只在 4℃ 和 40℃ 之间的温度下充电。
存储建议
1.最好将电池存放在阴凉、干燥、远离阳光直
废弃电池组请回收。
射、不会过热或过冷的地方。为了获得最佳的
电池性能和使用寿命,在不使用时请将电池组
存储在室温下。
2.长期存储时,建议将完全充电的电池组从充电
禁止焚烧电池组。
锂离子电池组充电。
器取出,存储在阴凉、干燥的地方,以达到电
池组的最佳性能。
充电时间,请参阅技术参数。
注意:电池组存储时不能处于电荷完全耗尽的状
态。在使用电池组之前,电池组必须重新充电。
22
只能在室内使用。
简体中文
包装内容
预期用途
本产品包装内的物品有:
本DCS331/DCS332曲线锯设计用于专业锯切木材、钢
1 充电式曲线锯
1 防划伤底脚垫
1 排渣联接口
2 锂离子电池组
1 充电器
1 说明书
注:N-型号不包括电池组、充电器和维修箱。
材、铝材、塑料和陶瓷材料。
禁止在潮湿环境中或在有易燃液体或气体的环境中
使用本工具。
此曲线锯是专业的电动工具。
请勿让儿童接触本工具。缺乏经验的操作员需要在
监督下使用本工具。
• 本 产品不适合体力、感觉或智力不足,或者
缺乏经验及知识的人员(包括小孩)使用,
除非一旁有能为他们的安全负责的监督人
•检 查工具、部件或配件是否在运输过程中损
员。不得在无人监管的情况下让儿童触及本
坏。
产品。
•操作前请花时间仔细阅读和理解本手册。
说明(图 1、2、6、10、11)
警 告:切勿改装电动工具或其任何部
件,否则可能会导致损坏或人身伤害。
a 电池释放按钮
电气安全
电机只适用一种工作电压。请务必检查电池组的电压
是否和铭牌上的电压一致。另外,请确保充电器电压
和主电源的电压一致。
DeWALT 充电器符合 IEC 60335 双重绝缘
b.电池组
要求,因此无需使用接地线。
c.触发开关
d.开关锁定按钮
如果电源线损坏,必须采用得伟维修机构提供的专用
e.锯片无键释放手柄
线。
f.坡口无键控制杆
使用延长线
g.底脚
仅在绝对必要时使用延长线。使用得延长线必须经
h.轨道模式控制柄
过批准并满足您充电器的功率输入(见“技术参
i.吹屑器控制拨杆
数”)要求。最小导体面积为1平方毫米,最大长
j.防划伤底脚垫
k.刀头夹持机构
度为30米。
使用电缆卷筒时,请确保电缆完全展开。
l.导向滚轮
组装与调整
m.后凸台
进行任何调整或取出/安装附加装置或
n.防裂插件
附件之前,请关闭工具并断开电池组连
p.主把手
q.顶部把手
警示:为降低严重的人身伤害风险,在
接。意外启动可能会导致人身伤害。
警示:只使用 DeWALT 电池组和充电
器。
23
简体中文
电池组在工具上的拆、装步骤(
图4)
4.释放锯片无键释放手柄。
注意:为达到最佳效果,请确保电池组已充满电。
电池组完全放电后,指示灯会在没有任何预警的情
否则会导致人身伤害。
1.抬起锯片无键释放手柄(e)。
况下关闭。
将电池组安装到工具手柄中
1. 把 电池组(b)与工具手柄内的轨道对正(图
4)。
2.把电池组滑入手柄,直至牢固固定,确保不会
松脱。
锯片拆卸
警示:锯片使用后会发烫,切勿接触;
2.轻轻摇动,锯片会自行掉出。
底脚坡口调节步骤(图7)
要松开底脚,请把坡口无键控制杆(f)向侧面拉。
要锁定底脚,请把坡口无键控制杆往回拉,直至曲
从工具上取出电池组
线锯锯身的下面。
1.按下电池释放按钮(a),把电池组用力从工
锯片坡口设定步骤
1.松开底脚。
具手柄中拉出。
2.按照本手册充电器部分的说明,将电池组插入
充电器。
电池组电量指示器(图4)
2.把底脚(g)向前滑动,将其从0°正停位置释
放。
3.底脚可左、右倾斜,并有15°、3 0 °和4 5°
一些 DeWALT 电池组带有一个包含三个绿色 LED 指
定位器。底脚可手动设定在0°至45°之间的
示灯的电量计,用于指示电池组内的剩余电量。
任何角度。
按下电量计按钮 (r) 不松开,即可启动电量计。三
4.坡口角度设定好之后,请把底脚锁定到位。
个绿色 LED 指示灯将以组合方式亮起,以指示剩余
把底脚设定回0°
电量。当电池内的电量低于可用限制时,电量计将
1.松开底脚。
不会亮起,电池将需要重新充电。
注意:电量指示器仅显示电池组的余电情况,与工
具的可用性能无关;电量显示随产品部件、温度、
2.转动底脚回0°。
3.把底脚滑动回0°正停位置。
用户使用情况而有所变化。
4.锁定底脚。
锯片安装与拆卸步骤(图 6)
锯切模式——轨道式或直线式(
图8)
安装锯片
注意:本曲线锯仅可使用T型柄曲线锯锯片。
注意:DT2074 齐边锯片仅可用于得伟 DCS331,
本曲线锯设计有四种锯切模式,三种轨道式、一种
直线式。轨道式锯片运动时,锯切强度大,可用
于锯切软材料,例如木材、塑料等。轨道式锯切
DCS332, DW331 和 DC330曲线锯。
速度更快,但在材料上的截面不够光滑。在轨道模
注意:安装齐边锯片(DT2074)时,必须拆下防开裂
式下,锯片在切削冲程中除了上下运动外,还向前
插件,并且底脚必须位于0°正停位置。
1.抬起锯片无键释放手柄(e),如图5所示。
运动。
2.把T型柄锯片插入夹持机构(k),同时引导锯
片背面进入导向轮槽中。
3.T型柄必须完全进入夹持机构,如图5所示。
24
注意:禁止使用轨道模式锯切金属或硬木。
锯切模式调整步骤, 将轨道模式控制柄(h)在四个
模式0、1、2、3位置间移动。0位是直线锯切模式。
简体中文
1、2、3位是轨道模式。控制柄从1到3变化时,锯切
强度增加。3位时强度最大。
吹屑器(图9)
吹屑器有助于清除锯切区域产生的锯屑。
注意:锯切金属时,请关闭吹屑器,避免吹掉锯片
上的切削液。
使用指南
警告:
•
请遵守安全说明及相关条例。
•
确 保工件放置可靠。去除钉子、螺
钉或其它可能损伤锯片的紧固件。
•
确 保工件下面有锯片通过的足够空
间。禁止切割超过锯片最大切割厚
要启动吹屑器,请把吹屑器控制拨杆(i)滑动到
最顶部。
度的材料。
•
仅 使用锋利的锯片。损坏或弯曲的
要关闭吹屑器,请把吹屑器控制拨杆滑动到最底
部。
锯片必须立刻更换。
•
禁 止 在 没 有 锯 片 的 情 况 下 启 动 工
可拆卸式防划伤底脚垫(图10)
锯切易划伤表面时,例如层压板、胶合板或油漆面
具。
•
为 了获得最佳效果,在工件表面连
等,应使用防划伤底脚垫(j)。
续平稳地移动工具。禁止对锯片施
要安装防划伤底脚垫,请将铝制底脚(g)的前部
加侧向力。
置于防划伤底脚垫(j)的前部内侧,然后放下曲线
•
必 须等工具完全停止后,再从工件
锯。底脚垫将咔嗒一声,牢牢卡到底脚的后部上。
上取出锯片。切割后,锯片可能发
要取下防划伤底脚垫,请从底部抓住底脚垫;抓牢
烫,禁止触摸。
两个后凸台(m),取下底脚垫。
防裂插件(图11)
手握工具的正确位置(图1,14)
注意:防裂插件不可与齐边锯片同时使用。需要
尽可能防止材料开裂时,特别是在锯割胶合板、层
压板或抛光面时,例如油漆面等,可使用防裂插件
(n)。防裂插件应安装到防划伤底脚垫(j)上。
如果不使用防划伤底脚垫,请把防裂插件安装到底
脚(g)上。
使用前的准备工作
• 确保电池组已充(满)电。
操作步骤
警告:为了减少严重人身伤害的危险,
调整或拆卸/安装附件或配件之前,请
按下触发开关锁定按钮并断开电池组。
意外启动容易导致人身伤害。
警告:务必正确佩戴听力保护装置。在
某些条件下或某些使用期间,本工具可
警告:为降低严重人身伤害风险,请务
必采用图示的正确手位。
警告:为降低严重人身伤害风险,请务
必紧握工具,预防突发反作用力。
正确的握持方式为一只手握住顶部把手(q),另
一只手握住主把手(p)。
扳手开关(图1)
开启曲线锯请按下触发开关 (C)。
减速并停止曲线锯请释放触发开关。
调速功能(图5)
按下触发开关的过程中,曲线锯的每分钟冲程数持
续升高,但不会超过工具的最大速度。释放触发开
关的过程中,锯片每分钟冲程数会降低。
未使用工具时,请务必按下工具的触发开关锁定按
钮(d), 以避免工具意外启动的风险。
能损伤听力。
25
简体中文
锯割步骤
维护
警告:切勿在拆下底脚的情况下使用曲
您的得伟电动工具设计精良,可以长期使用,仅需
线锯, 否则会造成严重人身伤害。
要极少维护。要连续获得令人满意的工作效果,需
挖锯(图12)
挖锯可以方便地进行内部锯割。本电锯可以直接插
要您进行正确的保养和定期的清洁。
进行任何调整或取出/安装附加装置或附
入板材,无须预先钻导向孔。挖锯时,请测量待锯
件之前,请关闭工具电源和断开电池组连
表面,并用铅笔标示清楚。然后把工具前倾,直至
底脚的前端紧靠在工件表面上,但锯片全冲程时不
接触工件。启动工具,待其达到最大速度。紧握工
警 告:为降低严重的人身伤害风险,在
接。意外启动容易造成人身伤害。
本充电器不可检修。充电器内不含可检修的部件。
具,降低工具后缘,直至锯片完全穿过材料。让底
脚水平停在木材上,开始锯割。工具仍在运动时,
切勿将锯片从锯缝中拔出。必须等锯片完全停止。
齐边锯(图13)
如果锯缝结束于墙面或后挡板等障碍物,需要进行
齐边锯。实现齐边锯的最简单方法之一是使用齐边
润滑剂
润滑导向滚轮(图6)
•定期在导向滚轮(l)上滴一滴油,防止卡锯。
锯片(DT2074) 。齐边锯片可达到曲线锯底脚的前
缘。安装、使用齐边锯片前,请取下防裂插件,把
底脚设定回0°正停位置。为获得最佳锯切质量,
请采用0或1轨道模式使用齐边锯片。开始锯割时不
可使用齐边锯片,因为使用齐边锯片时,底脚无法
清洁
尘屑,请用干燥的空气将灰尘和尘屑从
支撑到工件表面上。请参考下述木材锯切释例。
主机外壳内吹出。进行此步骤时,请佩
锯切木材步骤
任何条件下,均须充分固定工件。锯木材时请使用
高速设定。切勿在锯片接触材料时启动工具,这会
警告:一旦发现通风口及其周围积聚了
戴经认可的护目镜和面罩。
警告:切勿使用溶剂或其它刺激性化学
品来清洁工具的非金属部件。这些化学
导致马达停转。锯割时,将底脚前部置于材料上,
品可能削弱零件中使用的材料。只能使
把曲线锯底脚顶紧木材。切勿对工具强行用力;让
用抹布蘸中性肥皂水进行清洁。勿使任
锯片在自有速度下工作。锯割结束时,关闭曲线
何液体进入工具;勿使工具的任何部分
锯;待锯片完全停止后,将曲线锯取下并放置一
浸入液体中。
旁,然后再松开工件。
锯切金属步骤
充电器清洁说明
锯割较薄的金属板材时,最好在薄板材底部夹上木
警告:触电危险。清洁之前将充电器从
板。这能够确保锯缝整齐、消除振动并防止撕裂金
交流电插座上断开。使用软布或非金属
属板材。在锯切黑色金属(含铁量高的金属)时,
软刷,去除充电器外部的污垢和油脂。
请使用锯齿较细的锯片,而在锯割有色金属时(不
含铁的金属),可采用锯齿较粗的锯片。锯割软金
属(铝、铜、黄铜、低碳钢,镀锌管、薄钢板等)
时,使用高速设定;锯割塑料、瓷砖、层压板、硬
金属和铸铁时采用低速。
26
可选附件
警告:由于非得伟供应的配件未经本产
品匹配测试,将此类附件用于本工具可
能造成伤害。为降低人身伤害风险,本
产品只可使用得伟推荐的附件。
简体中文
请向您的经销商咨询更多关于合适附件的信息。
这些包括:
• DE3241 平行导轨
• DE3242 杠规脚
充电式电池组
• 581281-00 集尘口连接器
本电池组使用寿命长,不能提供顺利完成工作所需
• 581239-01 集尘袋
• 402140-00 防裂插件
• 581268-00 防划伤底脚垫
保护环境
分类回收。本产品不得与普通家庭垃圾
的电力时,必须进行充电。电池技术寿命结束时,
请妥善处理以保护环境。
• 耗尽电池组的电力,然后从工具上拆下。
• 锂离子电池是可回收的。将它们送往您的经销
商处或当地的回收站。回收的电池组将被妥善
循环使用或处理。
一起处理。
制 造 商 :Stanley Black & Decker Deutschland GmbH
地址:Black & DeckerStr.40 65510 Idstein, 德国
如果某一天您的得伟产品需要更换或不再使用,请
不要把它和家庭垃圾一起处理。请单独对本产品进
产地:捷克
行分类回收。
旧产品和旧包装的分类回收可使回收
材料得以再循环和再利用。再循环材
料的重新利用有助于防止环境污染
和减少原料需求。
城市垃圾站或您购买新产品的零售商会向您提供当
地家用电器产品分类回收的有关规定。
一旦产品到达它们的工作寿命,得伟提供回收和再
循环得伟产品的设施。如需利用此项服务,请将您
的产品送交任何经授权的维修代理商,他们将代表
我们回收这些产品。
您可通过联系本手册中所载的当地得伟办事处查询
最靠近您的授权维修代理的位置。此外,您也可以
通过网站获得授权的得伟维修代理列表以及我们售
后服务与联络方式的全部详情,网站
地址:www.2helpU.com。
27
N533340
05/2017
Download PDF