SCMTSA-1LHD | SCMTSA-1LHD IMPACT WRENCH instruction manual

SCMTSA-1LHD
Operation and Maintenance Manual
1’’
WARNING
Before operating this tool, all operators should study this manual to understand and follow the safety warnings and instructions. Keep these instructions
with the tool for future reference. If you have any questions, contact your Sidchrome® representative or distributor.
NS.1800F
1’’ Air
Impact Wrench
788272
SCMTSA-1LHD.2013.A
NU-NS.1800F/0110
TABLE OF CONTENTS
Introduction
Specifications
Safety Instructions
3
3
4
Getting Started
Tool Components
Contact Information
5
6
8
WARRANTY
Sidchrome air tools are warranted for TWO (2) years from the date of purchase, excluding normally wearing parts such as
vanes, gaskets and o-rings;
1. Unless otherwise specified, this warranty does not cover:
(a) modified, abused, neglected, accidentally damaged or excessively worn products, or products that have become
damaged or defective as a result of improper use;
(b) repairs attempted or made by other than our regional repair centre or authorised warranty service centre;
(c) conditions or malfunctions caused by the reasonable effects of fair wear and tear or the malfunction of normally
wearing parts, which include but are not limited to: vanes, gaskets, o-rings, driver blades, bumpers, pistons and
piston rings;
(Warranty non-transferrable) This warranty is not transferrable beyond the original purchaser.
2. How to make a warranty claim
Unless otherwise specified, the process for making a warranty claim is as follows:
(a) Any product subject to a warranty claim should be returned to the place of purchase for assessment by a
Sidchrome Australia distributor or representative. You are responsible for returning the product to the place of
purchase unless the cost of returning, removing or transporting the product is significant, in which case you
should contact Sidchrome Australia to make alternative arrangements.
(b) You must present proof of purchase when making a warranty claim.
(c) The claim under this warranty (you may have additional rights under the Australian Consumer Law) will be
assessed by a Sidchrome Australia distributor or representative on the basis of their product knowledge and
reasonable judgment and will be accepted if:
(i) a relevant defect is found;
(ii) the warranty claim is made during the relevant warranty period
(iii) none of the exclusions in cl 1. of this warranty apply.
(d) Upon acceptance of a claim under this warranty, Sidchrome Australia will send you a replacement product or
arrange for your product to be repaired free of charge.
(e) Any warranty related enquiries or claims may be directed to Sidchrome Australia at the address or contact details
listed below.
3. Repair notices
Goods presented for repair may be replaced by refurbished goods of the same type rather than being repaired.
Refurbished parts may be used to repair the goods.
The repair of your goods may result in the loss of any user-generated data. Please ensure that you have made a copy of any
data saved on your goods.
The Consumer Guarantee Statement
Our goods come with guarantees that cannot be excluded under Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are
also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.
Warranty related enquiries and claims may be directed to:
Sidchrome Australia
82 Taryn Drive, Epping, Victoria 3076
http://www.sidchrome.com.au/contact
Australia
Phone 1800 338 002
Fax 1800 080 898
2
New Zealand
Phone 0800 4782 6539
Fax 0800 278 265
INTRODUCTION
e Sidchrome® SCMTSA-1LHD is a precision-built tool, designed for high torque assembly and disassembly of
cient, dependable service when used correctly and with care. As with any
ne power tool, for best performance the manufacturer’s instructions must be followed. Please study this manual before
e instructions on installation, operation and
maintenance should be read carefully, and the manuals kept for reference. NOTE: Additional safety measures may be
required because of your particular application of the tool. Contact your Sidchrome® representative or distributor with
any questions concerning the tool and its use.
Sidchrome®
82 Taryn Drive, Epping
Victoria, Australia 3076
1800 338 002
Sidchrome.com.au
SPECIFICATIONS
6’’ Extended Anvil
D-Handle Design
For Improved
Ergonomics
Twin-Hammer
Impact Mechanism
ree-Position
Power Regulator
SPECIFICATIONS
Model #
Square
Drive
Blow
Rate
Breakaway
Torque
Vibration
Level
Noise Level
Pressure dB(A)
Power dB(A)
Pressure dB(C)
in
bpm
ft-lbs / Nm
SCMTSA- LHD
1
720
3000 / 4068
Model #
Free
Speed
Average Air
Consumption
rpm
cfm / l/min
psi / bar
lbs / kg
in / mm
SCMTSA- LHD
4500
8.6 / 243
90 / 6.2
24.2 / 11.0
20.7 x 8.0 x 6.8 / 525 x 203 x 172
* = measurement uncertainty in dB(A)
Working
Pressure
102.0
3*
112.9
3*
102.0
3*
m/s²
15.24
2**
Dimensions
Weight
** = measurement uncertainty in m/s²
3
WARNING
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING THE MACHINE.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
Do not use damaged, frayed or deteriorated air
hoses and fittings.
Always wear hearing protection when operating
this tool.
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using any
tool if discomfort, tingling feeling or pain occurs.
Seek medical advice before resuming use.
Always turn off the air supply and disconnect the air
supply hose before installing, removing or adjusting
any accessory on this tool, or before performing any
maintenance on this tool.
Do not carry the tool by the hose.
Always wear eye protection when operating or performing maintenance on this tool.
Keep body stance balanced and firm. Do not overreach when operating this tool.
Operate at 90 psig (6.2 bar / 620 kPa) Maximum air
pressure.
SAFE OPERATION
•
•
•
•
•
•
•
•
•
•
Always wear eye protection when operating or performing maintenance on this tool.
Always wear hearing protection when operating this tool.
Keep hands, loose clothing and long hair away from rotating end of tool.
Anticipate and be alert for sudden changes in motion during start up and operation of any power tool.
Keep body stance balanced and firm. Do not overreach when operating this tool.
Air powered tools can vibrate in use. Vibration, repetitive motions or uncomfortable positions may be harmful to
your hands and arms. Stop using any tool if discomfort, tingling feeling or pain occurs. Seek medical advice before
resuming use.
Use impact rated accessories recommended by Sidchrome®.
This tool is not designed for working in explosive atmospheres.
This tool is not insulated against electric shock.
Always turn off the air supply and disconnect the air supply hose before installing, removing or adjusting any
accessory on this tool, or before performing any maintenance on this tool.
PLACING TOOL IN SERVICE
LUBRICATION
Always use an air line lubricator with this tool. After every
eight hours of operation, if a lubricator is not used on the
compressed air network, inject 1.5 cc of approved air tool oil
through the tool’s inlet connection. Recommended air tool
oil available from Sidchrome SCMTSATO-250.
EMERGENCY
GATE VALVE
GETTING STARTED
•
•
•
•
•
•
•
•
1” SQ.
•
Always operate, inspect and maintain this tool in accordance with all regulations (local, state, federal and country)
that may apply to hand-held / hand-operated pneumatic tools.
For safety, top performance, and maximum durability of parts, operate this tool at 90 psig (6.2 bar / 620 kPa) maximum air pressure at the inlet with 3/4’’ (19mm) inside diameter air supply hose.
Always turn off the air supply and disconnect the air supply hose before installing, removing or adjusting any
accessory on this tool, or before performing any maintenance on this tool.
Do not use damaged, frayed or deteriorated air hoses and fittings.
Be sure all hoses and fittings are the correct size and are tightly secured.
Always use clean, dry air at 90 psig maximum air pressure. Dust, corrosive fumes and/or excessive moisture can
ruin the motor of an air tool.
Do not lubricate tools with flammable or volatile liquids such as kerosene, diesel or jet fuel.
Do not remove any labels. Replace any damaged label.
The use of a hose whip is recommended. A coupler connected directly to the air inlet increases tool bulk and
decreases tool maneuverability.
For maximum performance, the coupler on the wall should be the next size larger than the coupler used on the
tool. The coupler closest to the tool should not be less than the proper air supply hose size.
6.8” (172mm)
•
20.7” (525mm)
5
6
7
IMPACT ASSEMBLY
HAMMER PIN
HAMMER FRAME
HAMMER
ANVIL ASSEMBLY
HOUSING ASSEMBLY
BACKHEAD ASSEMBLY
BUSHING
REVERSE VALVE BUSHING
REVERSE VALVE ASSEMBLY
SPRING PIN
REAR END PLATE ASSEMBLY
BALL BEARING
FRONT END PLATE ASSEMBLY
BALL BEARING
SCREW ASSEMBLY
SPRING WASHER
31D100023
31H100027
31M100009
31P100011
31M100008
31M100010
31R100001
C
35
36
37
A
33
56
60
1
2
15
17
20
24
23
30
31
21A
21
HELI-COIL
STEEL BALL
HAMMER CASE ASSEMBLY
BUSHING
HAMMER CASE
SCREW ASSEMBLY
SPRING WASHER
OIL SEAL
31H100016
B
41
43
44
44A
47
31D100022
ANVIL ASSEMBLY
6" EXTENDED ANVIL
O-RING
SOCKET RETAINER
31D100022
31D200040
31R200192
31R200193
A
38B
48
49
DESCRIPTION
1" Impact Wrench
PART #
SCMTSA-1LHD
ITEM #
4
4
1
1
1
1
1
1
1
1
1
1
8
4
1
2
1
2
1
1
1
1
4
4
1
1
1
1
1
QTY
10B
13A
52
53
TK
5
6
16
18
19
22
23
26
31
32
34
42
48
49
2A
3
4
11
12
13
14
27
28
29
29A
40
45
59
ITEM #
46
46A
31Y200061
31Y200060
31R200204
31Y200062
31M100015
31Y200057
31R200198
31Y200058
31H200006
31R200200
31Y200059
31R200201
31M200045
31M200046
31R200209
31R200183
31R200187
31H200007
31R200205
PART #
31R100003
OPTIONAL - AIR INLET
OPTIONAL - OUTSIDE TRIGGER
OPTIONAL - LOCK NUT
OPTIONAL - AIR INLET
TUNE UP KIT
SPRING
O-RING
O-RING
STEEL BALL
SPRING
GASKET
BALL BEARING
ROTOR BLADE
BALL BEARING
GASKET
BALL BEARING
GASKET
O-RING
SOCKET RETAINER
THROTTLE VALVE SEAT
THROTTLE VALVE PLUNGER (INSIDE)
THROTTLE VALVE
RUBBER CAP (INSIDE)
PIN
INSIDE TRIGGER
SPRING PIN
ROTOR
CYLINDER
SPRING PIN
SPRING PIN
WASHER
SIDE SPADE HANDLE
THROTTLE VALVE PLUNGER (OUTSIDE)
DESCRIPTION
SCREW ASSEMBLY
SPRING WASHER
1
1
1
1
1
1
1
6
1
1
1
1
1
1
1
1
1
1
2
1
2
1
1
1
1
1
1
1
QTY
4
4
Download PDF

advertising