D25501K | DeWalt D25501K ROTARY HAMMER Type 2 instruction manual

D25501
D25601
D25604
D25831
Final Page Size: 172 x 240 mm
English (original instructions)4
Fig. A
11
6
4
1
10
14
9
3
D25501
6
6
11
5
4
1
10
D25501, D25601, D25604
14
2
9
7
6
5
D25601, D25604
3
D25831
3
11
6
5
4
10
14
1
7
8
5
D25831
1
Fig. B
15
12
3
12
3
D25501, D25601, D25604
D25831
8
Fig. C
7
16
17
D25601, D25604, D25831
2
Fig. D
Fig. E
6
11
Fig. F
4
3
D25601, D25604
D25
3
English
SDS MAX COMBINATION & CHIPPING HAMMERS
D25501, D25601, D25604, D25831
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make DeWALT one of the most reliable partners for
professional power tool users.
Technical Data
Voltage
UK & Ireland
Type
Frequency
Power input
No load speed
No load beats per-minute
Single impact energy (EPTA 05/2009)
Total drilling range in concrete:
solid bits
core bits
Optimum drilling range in concrete:
solid bits
Chisel positions
Tool holder
Weight
Hz
W
min-1
bpm
J
D25501
230
230/115
2
50
1100
490
3300
8
D25601
230
230/115
3
50
1250
210–415
1430–2840
2–8
D25604
230
230/115
3
50
1250
210–415
1430–2840
2–8
D25831
230
230/115
3
50
1250
–
1430–2840
2–8
mm
mm
12–40
40–90
12–45
40–100
12–45
40–100
–
–
mm
18–26
18
SDS Max
6.15
25–35
18
SDS Max
6.8
25–35
18
SDS Max
6.9
–
18
SDS Max
6.1
94
105
3
94
105
3
94
105
3
93
104
3
m/s2
m/s2
17.2
1.5
8.9
1.5
8.9
1.5
–
–
m/s2
m/s2
12.4
1.5
7.1
1.5
7.1
1.5
12.1
1.5
VAC
VAC
kg
Noise values and vibration values (triax vector sum) according to EN60745-2-6:
dB(A)
LPA(emission sound pressure level)
dB(A)
LWA(sound power level)
K(uncertainty for the given sound level)
dB(A)
Drilling into concrete
Vibration emission value ah, HD =
Uncertainty K =
Chiselling
Vibration emission value ah,Cheq =
Uncertainty K =
The vibration emission level given in this information sheet has been
measured in accordance with a standardised test given in EN60745 and
may be used to compare one tool with another. It may be used for a
preliminary assessment of exposure.
WARNING: The declared vibration emission level represents the
main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the
vibration emission may differ. This may significantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration should also take
into account the times when the tool is switched off or when it is
running but not actually doing the job. This may significantly reduce
the exposure level over the total working period.
Identify additional safety measures to protect the operator from the
effects of vibration such as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
4
EC-Declaration of Conformity
Machinery Directive
SDS Max Combination & Chipping Hammers
D25501, D25601, D25604, D25831
DeWALT declares that these products described under Technical Data are
in compliance with:
2006/42/EC, EN60745-1:2009+A11:2010, EN60745-2-6:2010.
D25831
2000/14/EC Electrical concrete breaker (hand held) m </= 15kg, Annex VIII;
TÜV Rheinland LGA Products GmbH (0197), D-90431 Nürnberg, Germany
Notified Body ID No.: 0197
Level of sound power according to 2000/14/EC (Article 12, Annex III, No. 10;
m </= 15 kg)
English
LWA (measured sound power level)
LWA (guaranteed sound power level)
dB
dB
101
105
These products also comply with Directive 2014/30/EU/ and 2011/65/EU.
For more information, please contact DeWALT at the following address
or refer to the back of the manual. The undersigned is responsible for
compilation of the technical file and makes this declaration on behalf
of DeWALT.
d ) Do not abuse the cord. Never use the cord for carrying, pulling
or unplugging the power tool. Keep cord away from heat,
oil, sharp edges or moving parts. Damaged or entangled cords
increase the risk of electric shock.
e ) When operating a power tool outdoors, use an extension cord
suitable for outdoor use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f ) If operating a power tool in a damp location is unavoidable,
use a residual current device (RCD) protected supply. Use of an
RCD reduces the risk of electric shock.
3) Personal safety
Markus Rompel
Director Engineering
DeWALT, Richard-Klinger-Straße 11,
D-65510, Idstein, Germany
03.11.2017
WARNING: To reduce the risk of injury, read the instruction manual.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal word.
Please read the manual and pay attention to these symbols.
DANGER: Indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury which,
if not avoided, may result in property damage.
Denotes risk of electric shock.
Denotes risk of fire.
General Power Tool Safety Warnings
WARNING: Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in electric shock,
fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
1) Work area safety
a ) Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b ) Do not operate power tools in explosive atmospheres, such as
in the presence of flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c ) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2) Electrical safety
a ) Power tool plugs must match the outlet. Never modify the
plug in any way. Do not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs and matching outlets
will reduce risk of electric shock.
b ) Avoid body contact with earthed or grounded surfaces such as
pipes, radiators, ranges and refrigerators. There is an increased
risk of electric shock if your body is earthed or grounded.
c ) Do not expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
a ) Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power tool
while you are tired or under the influence of drugs, alcohol
or medication. A moment of inattention while operating power tools
may result in serious personal injury.
b ) Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c ) Prevent unintentional starting. Ensure the switch is in the off
position before connecting to power source and/or battery
pack, picking up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools that have the
switch on invites accidents.
d ) Remove any adjusting key or wrench before turning the power
tool on. A wrench or a key left attached to a rotating part of the
power tool may result in personal injury.
e ) Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situations.
f ) Dress properly. Do not wear loose clothing or jewellery. Keep
your hair, clothing and gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught in moving parts.
g ) If devices are provided for the connection of dust extraction
and collection facilities, ensure these are connected
and properly used. Use of dust collection can reduce dustrelated hazards.
4) Power tool use and care
a ) Do not force the power tool. Use the correct power tool for
your application. The correct power tool will do the job better and
safer at the rate for which it was designed.
b ) Do not use the power tool if the switch does not turn it on
and off. Any power tool that cannot be controlled with the switch is
dangerous and must be repaired.
c ) Disconnect the plug from the power source and/or the battery
pack from the power tool before making any adjustments,
changing accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool accidentally.
d ) Store idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool. Power tools are dangerous
in the hands of untrained users.
e ) Maintain power tools. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that
may affect the power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents are caused by
poorly maintained power tools.
f ) Keep cutting tools sharp and clean. Properly maintained cutting
tools with sharp cutting edges are less likely to bind and are easier
to control.
5
English
g ) Use the power tool, accessories and tool bits etc., in accordance
with these instructions taking into account the working
conditions and the work to be performed. Use of the power
tool for operations different from those intended could result in a
hazardous situation.
5) Service
a ) Have your power tool serviced by a qualified repair person
using only identical replacement parts. This will ensure that the
safety of the power tool is maintained.
Additional Safety Instructions for Rotary Hammers
• Wear ear protectors. Exposure to noise can cause hearing loss.
• Use auxiliary handle 3 , if supplied with the tool. Loss of control can
cause personal injury.
• Hold power tool by insulated gripping surfaces, when performing
an operation where the cutting accessory may contact hidden
wiring or its own cord. Cutting accessory contacting a “live” wire
may make exposed metal parts of the power tool “live” and could
give the operator an electric shock.
WARNING: We recommend the use of a residual current device with a
residual current rating of 30mA or less.
Package Contents
The package contains:
1 Rotary hammer (D25501, D25601, D25604)
or
1 Chipping hammer (D25831)
1 Side handle
1 Kitbox (K-models only)
1 Instruction manual
• Check for damage to the tool, parts or accessories which may have
occurred during transport.
• Take the time to thoroughly read and understand this manual prior
to operation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Residual Risks
Wear eye protection.
In spite of the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks cannot be avoided.
These are:
• Impairment of hearing.
• Risk of personal injury due to flying particles.
• Risk of burns due to accessories becoming hot during operation.
• Risk of personal injury due to prolonged use.
Red service indicator LED. For detailed description see under
Service Indicator LED's.
Yellow service indicator LED. For detailed description see under
Service Indicator LED's.
Electrical Safety
The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.
Your DeWALT tool is double insulated in accordance with
EN60745; therefore no earth wire is required.
WARNING: 115 V units have to be operated via a fail-safe isolating
transformer with an earth screen between the primary and
secondary winding.
If the supply cord is damaged, it must be replaced by a specially prepared
cord available through the DeWALT service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Using an Extension Cable
An extension cord should not be used unless absolutely necessary. Use an
approved extension cable suitable for the power input of your charger (see
Technical Data). The minimum conductor size is 1.5 mm2; the maximum
length is 30 m.
When using a cable reel, always unwind the cable completely.
6
Visible radiation. Do not stare into light.
Date Code Position (Fig. A)
The date code 14 , which also includes the year of manufacture, is printed
into the housing.
Example:
2018 XX XX
Year of Manufacture
Description (Fig. A)
WARNING: Never modify the power tool or any part of it. Damage or
personal injury could result.
1 Trigger switch (D25501, D25601, D25604)
On/off rocker switch (D25831)
2 Lock-on slider (D25604)
3 Side handle
4 Main handle
5 Active vibration control (D25601, D25604, D25831)
6 Mode selector switch
7 Electronic speed and impact control dial (D25601, D25604, D25831)
8 Side handle knob (D25831)
9 Side handle clamp (D25501, D25601, D25604)
10 Tool holder
11 Locking sleeve
Intended Use
The D25501, D25601, D25604 rotary hammers have been designed for
professional rotary drilling and chipping applications.
The D25831 chipping hammers have been designed for professional
chipping, chiselling and demolition applications.
English
DO NOT use under wet conditions or in the presence of flammable liquids
or gases.
These hammers are professional power tools.
DO NOT let children come into contact with the tool. Supervision is
required when inexperienced operators use this tool.
• Young children and the infirm. This appliance is not intended for use
by young children or infirm persons without supervision.
• This product is not intended for use by persons (including children)
suffering from diminished physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are supervised by a person
responsible for their safety. Children should never be left alone with
this product.
Soft Start Feature
D25601, D25604, D25831
The soft start feature allows the tool to accelerate slowly, thus preventing
the drill bit from walking off the intended hole position when starting.
The soft start feature also reduces the immediate torque reaction
transmitted to the gearing and the operator if the hammer is started with
the drill bit in an existing hole.
Electronic Speed and Impact Control (Fig. A, C)
D25601, D25604, D25831
The electronic speed and impact control 7 offers the following advantages:
-- use of smaller accessories without risk of breakage;
-- minimised break-out when chiselling or drilling in soft or
brittle materials;
-- optimal tool control for precise chiselling.
Torque Limiting Clutch
WARNING: The user must always maintain a firm grip on the tool
when in operation.
The torque limiting clutch reduces the maximum torque reaction
transmitted to the operator in case of jamming of a drill bit. This feature also
prevents the gearing and electric motor from stalling.
Anti-Rotation System (Fig. C)
D25604
Ant-Rotation System offers increased user comfort and safety through an
on-board, anti-rotation technology capable of detecting if the user loses
control of the hammer. When a jam is detected, the torque and speed are
reduced instantly. This feature prevents self rotation of the tool reducing the
occurrence of wrist injuries.
Service Indicator LEDs (Fig. A, C)
D25601, D25604, D25831
The yellow brushwear indicator LED 17 lights up when the carbon brushes
are nearly worn out to indicate that the tool needs servicing within the next
8 hours of use.
D25604
The red service indicator LED 16 lights up if the lock-on button 2 is
used in any mode except the chipping mode. On models fitted with
Ultimate Torque Control (UTC), the red LED indicator 16 lights up if the
anti-rotational device is activated. The red indicator starts to flash if there
is a fault with the tool or the brushes have completely worn out (refer to
Brushes under Maintenance).
D25601, D25831
The red service indicator LED 16 lights up if there is a fault with
the tool or the brushes have completely worn out (refer to Brushes
under Maintenance).
Under exposure of certain electromagnetic phenomena(fast transients) it
can happen that the machine will reduce speed down to zero RPM. This
will be shown by flashing of the service indicator. To undo this mode the
machine needs to be switched off and on one time. After cycling the trigger
switch the machine is back in normal operating mode.
Fully Vibration-Dampened Main Handle (Fig. A)
D25601, D25604, D25831
The dampers in the main handle 4 absorb the vibrations transmitted to
the user. This improves user comfort during the operation.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal injury,
turn tool off and disconnect tool from power source before
making any adjustments or removing/installing attachments
or accessories. An accidental start-up can cause injury.
Fitting the Side Handle (Fig. B)
The side handle 3 clamps to the mounting area 12 of the gear case and
may be rotated 360˚ to permit right- or left-hand use. The side handle
must be tightened sufficiently to resist the twisting action of the tool if the
accessory binds or stalls. Be sure to grip the side handle at the far end to
control the tool during a stall.
To loosen side handle, rotate counterclockwise.
Inserting and Removing SDS Max Accessories
(Fig. A, D)
This machine uses SDS Max bits and chisels (refer to the inset in Figure D for
a cross-section of an SDS Max bit shank).
1. Clean the bit shank.
2. Pull back the locking sleeve 11 and insert the bit shank.
3. Turn the bit slightly until the sleeve snaps into position.
4. Pull on the bit, to check if it is properly locked. The hammering function
requires the bit to be able to move axially several centimetres when
locked in the tool holder.
5. To remove a bit pull back the tool holder locking sleeve/collar 11 and
pull the bit out of the tool holder 10 .
Selecting the Operating Mode (Fig. A)
Hammerdrilling:
D25501, D25601, D25604
for concrete, brick, stone and masonry drilling operations.
Hammering only:
D25501, D25601, D25604, D25831
for chiselling and demolition applications. In this mode the tool
can also be used as a lever to free a jammed drill bit.
1. To select the operating mode, rotate the mode selector switch 6 until
it points to the symbol of the required mode.
It may be neccessary to twist the tool holder 10 slightly to allow the
mode selector switch 6 to pass the
position.
2. Check that the mode selector switch 6 is locked in place.
Indexing the Chisel Position (Fig. E)
The chisel can be indexed and locked into 18 different positions.
1. Rotate the mode selector switch 6 until it points towards the
position.
2. Rotate the chisel in the desired position.
3. Set the mode selector switch 6 to the “hammering only” position.
4. Twist the chisel until it locks in position.
Setting the Electronic Speed and Impact Control Dial
(Fig. A, C)
D25601, D25604, D25831
Turn the dial 7 to the desired level. Turn the dial upwards for higher
speed and downwards for lower speed. The required setting is a matter of
experience, e.g.
• when chiselling or drilling in soft, brittle materials or when minimum
break-out is required, set the dial to a low setting;
7
English
• when breaking or drilling in harder materials, set the dial to a
high setting.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal injury,
turn tool off and disconnect tool from power source before
making any adjustments or removing/installing attachments
or accessories. An accidental start-up can cause injury.
WARNING: Tool bits may be hot and gloves should be worn when
changing or removing them to avoid personal injury.
WARNING:
• Be aware of the location of pipework and wiring.
• Apply only a gentle pressure to the tool (approximately 20 kg).
Excessive force does not speed up drilling but decreases tool
performance and may shorten tool life.
• Always hold the tool firmly with both hands and ensure a
secure stance. Always operate the tool with the side handle
properly assembled.
NOTE: Operating temperature is -7 ˚ to +40 ˚C. Using the tool outside of
this temperature range will decrease the life of the tool.
Proper Hand Position (Fig. F)
WARNING: To reduce the risk of serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of serious personal injury, ALWAYS hold
securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the side handle 3 , with the
other hand on the main handle 4 .
Switching On and Off (Fig. A)
D25501, D25604
To turn the tool on, depress the trigger switch 1 .
To stop the tool, release the trigger switch.
D25604
The lock-on slider 2 allows the trigger switch 1 to be locked on in
chiselling mode only. If the lock-on button is activated in drilling mode, as a
feature the tool will switch off automatically.
To turn the tool on, press the trigger switch 1 .
To stop the tool, release the switch.
For continuous operation, press and hold down the switch 1 , slide the
lock-on slider 2 upwards and release the switch.
To stop the tool in continuous operation, press the switch briefly
and release it. Always switch off the tool when work is finished and
before unplugging.
D25831
To turn the tool on, press the on/off rocker switch 1 at the lower part of
the trigger.
To stop the tool, press the on/off rocker switch at the upper part of
the trigger.
Hammerdrilling
To turn the tool on, press the on/off switch 1 .
To stop the tool, release the switch.
8
Drilling with a Solid Bit (Fig. A)
D25501, D25601, D25604
1. Insert the appropriate drill bit.
2. Set the mode selector switch 6 to the hammerdrilling position.
3. D25601, D25604 only: Set the electronic speed and impact control
dial 7 .
4. Fit and adjust the side handle 3 .
5. Mark the spot where the hole is to be drilled.
6. Place the drill bit on the spot and switch on the tool.
7. Always switch off the tool when work is finished and
before unplugging.
Drilling with a Core Bit (Fig. A)
D25501, D25601, D25604
1. Insert the appropriate core bit.
2. Assemble the centerdrill into the core bit.
3. Set the mode selector switch 6 to the hammerdrilling position.
4. D25601, D25604 only: Turn the electronic speed and impact control
dial 7 to a medium or high speed setting.
5. Fit and adjust the side handle 3 .
6. Place the centerdrill on the spot and switch on the tool. Drill until the
core penetrates into the concrete approximately 1 cm.
7. Stop the tool and remove the centerdrill. Place the core bit back into the
hole and continue drilling.
8. When drilling through a structure thicker than the depth of the core
bit, break away the round cylinder of concrete or core inside the bit at
regular intervals.
To avoid unwanted breaking away of concrete around the hole, first drill
a hole the diameter of the centerdrill completely through the structure.
Then drill the cored hole halfway from each side.
9. Always turn the tool off when work is finished and before unplugging.
Chipping and Chiselling (Fig. A)
1. Insert the appropriate chisel and rotate it by hand to lock it into one of
18 positions.
2. Set the mode selector switch 6 to the hammering only position.
3. D25601, D25604, D25831 only: Set the electronic speed and impact
control dial 7 .
4. Fit and adjust the side handle 3 .
5. Turn the tool on and start working.
6. Always turn the tool off when work is finished and before unplugging.
MAINTENANCE
Your DeWALT power tool has been designed to operate over a long period
of time with a minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of serious personal injury,
turn tool off and disconnect tool from power source before
making any adjustments or removing/installing attachments
or accessories. An accidental start-up can cause injury.
Brushes (Fig. C)
The carbon brushes are not user-serviceable. Take the tool to an authorized
DeWALT repair agent.
The yellow brushwear indicator LED 17 lights up when the carbon brushes
are nearly worn out. After a further 8 hours of use or after the brushes have
completely worn out, the motor will automatically be shut off.
Tool maintenance needs to be carried out as soon as the service
indicator 16 lights up.
English
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of the main housing with dry air
as often as dirt is seen collecting in and around the air vents. Wear
approved eye protection and approved dust mask when performing
this procedure.
WARNING: Never use solvents or other harsh chemicals for cleaning
the non-metallic parts of the tool. These chemicals may weaken the
materials used in these parts. Use a cloth dampened only with water
and mild soap. Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
Optional Accessories
WARNING: Since accessories, other than those offered by DeWALT,
have not been tested with this product, use of such accessories with
this tool could be hazardous. To reduce the risk of injury, only DeWALT
recommended accessories should be used with this product.
Consult your dealer for further information on the appropriate accessories.
Protecting the Environment
Separate collection. Products and batteries marked with this
symbol must not be disposed of with normal household waste.
Products and batteries contain materials that can be recovered or
recycled reducing the demand for raw materials. Please recycle
electrical products and batteries according to local provisions. Further
information is available at www.2helpU.com.
9
Belgique et
Luxembourg België
en Luxemburg
DeWALT - Belgium BVBA
Egide Walschaertsstraat 16
2800 Mechelen
Tel: NL 32 15 47 37 63
Tel: FR 32 15 47 37 64
Fax:
32 15 47 37 99
www.dewalt.be
enduser.BE@SBDinc.com
Danmark
DeWALT
Roskildevej 22
2620 Albertslund
Tel:
Fax:
www.dewalt.dk
kundeservice.dk@sbdinc.com
Deutschland
DeWALT
Richard Klinger Str. 11
65510 Idstein
Tel:06126-21-1
Fax:06126-21-2770
www.dewalt.de
infodwge@sbdinc.com
Ελλάς
DeWALT (Ελλάς) Α.Ε.
EΔΡΑ-ΓΡΑΦΕΙΑ : Στράβωνος 7
& Λ. Βουλιαγμένης, Γλυφάδα 166 74, Αθήνα
SERVICE : Ημερος Τόπος 2 (Χάνι Αδάμ) – 193 00 Ασπρόπυργος
Τηλ:00302108981616
Φαξ:00302108983570
www.dewalt.gr
Greece.Service@sbdinc.com
España
DeWALT Ibérica, S.C.A.
Parc de Negocios “Mas Blau”
Edificio Muntadas, c/Bergadá, 1, Of. A6
08820 El Prat de Llobregat (Barcelona)
Tel:
Fax:
934 797 400
934 797 419
www.dewalt.es
respuesta.postventa@sbdinc.com
France
DeWALT
5, allée des Hêtres
BP 30084, 69579 Limonest Cedex
Tel:
Fax:
04 72 20 39 20
04 72 20 39 00
www.dewalt.fr
scufr@sbdinc.com
Schweiz
Suisse
Svizzera
DeWALT
In der Luberzen 42
8902 Urdorf
Tel:
Fax:
044 - 755 60 70
044 - 730 70 67
www.dewalt.ch
service@rofoag.ch
Ireland
DeWALT
Calpe House Rock Hill
Black Rock, Co. Dublin
Tel:00353-2781800
Fax:00353-2781811
www.dewalt.ie
Italia
DeWALT
via Energypark
20871 Vimercate (MB), IT
Tel: Fax: 800-014353
39 039 9590200
39 039 9590313
www.dewalt.it
Nederlands
DeWALT Netherlands BV
Holtum Noordweg 35
6121 RE BORN, Postbus 83, 6120 AB BORN
Tel:
Fax:
31 164 283 063
31 164 283 200
www.dewalt.nl
Norge
DeWALT
Postboks 4613, Nydalen
0405 Oslo
Tel: Fax: 45 25 13 00
45 25 08 00
www.dewalt.no
kundeservice.no@sbdinc.com
Österreich
DeWALT
Werkzeug Vertriebsges m.b.H
Oberlaaerstrasse 248, A-1230 Wien
Tel: Fax: 01 - 66116 - 0
01 - 66116 - 614
www.dewalt.at
service.austria@sbdinc.com
Portugal
DeWALT Limited, SARL
Centro de Escritórios de Sintra Avenida
Almirante Gago Coutinho, 132/134, Edifício 14
2710-418 Sintra
Tel: Fax: 214 66 75 00
214 66 75 80
www.dewalt.pt
resposta.posvenda@sbdinc.com
Suomi
DeWALT
PL 47
00521 Helsinki
Puh: Faksi:
010 400 4333
0800 411 340
www.dewalt.fi
asiakaspalvelu.fi@sbdinc.com
Sverige
DeWALT
Box 94
431 22 Mölndal
Tel:
Fax: 031 68 61 60
031 68 60 08
www.dewalt.se
kundservice.se@sbdinc.com
Türkiye
KOZYATAGI MAHALLESI DEGIRMEN SOKAK NIDA KULE NO: 18/6
KADIKOY/ÍSTANBUL - TÜRKIYE
Erenkoy Vergi Dairesi 7810504649
Tel: Faks:
0090 216 665 29 00
00 0216 665 29 01
www.dewalt.com.tr
info-tr@sbdinc.com
United
Kingdom
DeWALT, 210 Bath Road;
Slough, Berks SL1 3YD
Tel: Fax: 01753-567055
01753-572112
www.dewalt.co.uk
emeaservice@sbdinc.com
Australia
DeWALT
82 Taryn Drive, Epping
VIC 3076 Australia
Tel: Aust 1800 338 002
Tel: NZ 0800 339 258
www.dewalt.com.au
www.dewalt.co.nz
Middle East Africa
DeWALT
P.O. Box - 17164,
Jebel Ali Free Zone (South), Dubai, UAE
Tel: Fax: www.dewalt.ae
Service.MEA@sbdinc.com
70 20 15 10
70 22 49 10
971 4 812 7400
971 4 2822765
N62196006/18
Download PDF

advertising