FMCW210 | Stanley FMCW210 SANDER instruction manual

1
4
2
3
FMCW210
Charging
4
5
Fully Charged
Hot/Cold Pack Delay
Bad Battery
5a
B
A
4a
4
4
C
D
6
E
8
8
7
F
2
10
2
9
G
3
H
2a
(Original instructions)
Intended use
Your Stanley Fat Max FMCW210 sander has been designed
for sanding wood, metal, plastics and painted surfaces. This
appliance is intended for professional and private, non professional users.
Safety instructions
General power tool safety warnings
@
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
ENGLISH
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
4
ENGLISH
(Original instructions)
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Battery tool use and care
a. Recharge only with the charger specified by the
manufacturer.
A charger that is suitable for one type of battery pack may
create a risk of fire when used with another battery pack
b. Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire
c. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws, or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire
d. Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
e. Do not use a battery pack or tool that is damaged or
modified. Damaged or modified batteries may exhibit
unpredictable behaviour resulting in fire, explosion or risk
of injury.
f. Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or temperature
above 265º F may cause explosion.
g. Follow all charging instructions and do not charge the
battery pack or tool outside the temperature range
specified in the instructions. Charging improperly or at
temperatures outside the specified range may damage the
battery and increase the risk of fire
6. service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
5
b. Never service damaged battery packs. Service of
battery packs should only be performed by the
manufacturer or authorised service providers.
@
Additional power tool safety warnings
@
u
u
@
@
u
Warning! Contact with or inhalation of dusts
arising from sanding applications may endanger
the health of the operator and possible bystanders. Wear a dust mask specifically designed for
protection against dust and fumes and ensure
that persons within or entering the work area are
also protected.
Hold power tool by insulated gripping surfaces when
performing an operation where the sanding accessory
may contact hidden wiring. Accessory contacting a "live"
wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
@
u
Warning! Additional safety warnings for sanders
Warning! Take special care when sanding some
woods (e.g. beech, oak) and metal which may
produce toxic dust. Wear a dust mask specifically designed for protection against toxic dust
and fumes and ensure that persons within or
entering the work area are also protected.
Warning! Use this tool in a well ventilated area
when sanding ferrous metals. Do not operate
the tool near flammable liquids, gases or dust.
Sparks or hot particles from sanding or arcing
motor brushes may ignite combustible materials.
Warning! Do not sand magnesium! There is a
risk of fire or explosions.
Thoroughly remove all dust after sanding.
The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recommended in this instruction manual may present a risk of
personal injury and/or damage to property.
(Original instructions)
@
Safety when sanding paint






.
Warning! Observe the applicable regulations
.
for sanding paint. Pay special attention to the
following:
Whenever possible, use a vacuum extractor for dust collection.
Take special care when sanding paint which is possibly
lead based and may produce toxic dust:
Do not let children or pregnant women enter the work
area.
All persons entering the work area should wear a mask
specially designed for protection against lead paint dust
and fumes.
Do not eat, drink or smoke in the work area.
Dispose of dust particles and any other removal debris
safely.
Safety of others
u
u
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a person responsible for their
safety.
Children should be supervised to ensure that they do not
play with the appliance.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving parts.
u Injuries caused when changing any parts, blades or accessories.
u Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
ENGLISH
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured
in accordance with a standard test method provided by
EN 60745 and may be used for comparing one tool with
another. The declared vibration emission value may also be
used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Additional safety instructions for batteries and
chargers
Batteries
u
u
u
u
u
u
Never attempt to open for any reason.
Do not expose the battery to water.
Do not store in locations where the temperature may
exceed 40 °C.
Charge only at ambient temperatures between 10 °C and
40 °C.
Charge only using the charger provided with the tool.
When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
Do not attempt to charge damaged batteries.
Chargers
u
u
u
u
u
Use your BLACK+DECKER charger only to charge
the battery in the tool with which it was supplied. Other
batteries could burst, causing personal injury and damage.
Never attempt to charge non-rechargeable batteries.
Have defective cords replaced immediately.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
$
u
The charger is intended for indoor use only.
Read the instruction manual before use.
6
ENGLISH
(Original instructions)
Labels on tool
The following pictograms along with the date code are shown
on the tool:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Wear a dust mask.
Electrical safety
#
u
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on the
rating plate. Never attempt to replace the charger
unit with a regular mains plug.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Stanley Fat Max Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Dust collection cassette
3. Sanding base
4. Finger attachment
5. Battery
Accessories
The accessories supplied with your sander depend upon the
model that you have purchased. All the accessories listed
below are available in our range. If you require an accessory
that is listed below but is not supplied with your sander please
visit our website at www.blackanddecker.eu.
The performance of your tool depends on the accessory used.
Stanley Fat Max accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
7
Item
Description
240 grit sanding mesh.
For a fine finish for large detail sanding.
(Part Number - X39132-XJ)
120 grit sanding mesh.
For a medium finish for large detail
sanding.
(Part Number - X39127-XJ)
80 grit sanding mesh.
For a coarse finish for large detail
sanding.
(Part Number - X39122-XJ)
240 grit large detail sanding sheet
with two replacement tips.
For a fine finish for large detail sanding.
(Part Number - X31019-XJ)
120 grit large detail sanding sheet
with two replacement tips.
For a medium finish for large detail
sanding.
(Part Number - X31009-XJ)
60 grit large detail sanding sheet with
two replacement tips.
For a coarse finish for large detail
sanding.
(Part Number - X31039-XJ)
120 grit detailed finger sanding sheet.
For a medium finish for detailed sanding.
(Part Number - X3277-XJ)
Charging procedure (Fig. A)
Stanley Fat Max chargers are designed to charge Stanley Fat
Max battery packs.
u Plug the charger (5) into an appropriate outlet before
inserting the battery pack (4).
u Insert the battery pack (4) into the charger (5) as shown in
figure A.
u The LED (5a) will flash indicating that the battery is being
charged.
u The completion of charge is indicated by the LED (5a)
remaining on continuously.
The pack is fully charged and may be used at this time or
left on the charger.
Note: Recharge discharged batteries as soon as possible
after use or battery life may be greatly diminished. For longest
battery life, do not discharge batteries fully.
(Original instructions)
It is recommended that the batteries be recharged after each
use.
Leaving the battery in the charger
The charger (5) and battery pack (4) can be left connected
with the LED glowing indefinitely.
The charger will keep the battery pack fresh and fully charged.
Important charging notes
Longest life and best performance can be obtained if
the battery pack is charged when the air temperature is
between 65°F and 75°F (18°- 24°C). DO NOT charge the
battery pack in an air temperature below +40°F (+4.5°C),
or above +105°F (+40.5°C). This is important and will
prevent serious damage to the battery pack.
u The charger and battery pack may become warm to touch
while charging. This is a normal condition, and does not
indicate a problem. To facilitate the cooling of the battery
pack after use, avoid placing the charger or battery pack
in a warm environment such as in a metal shed, or an
uninsulated trailer.
u If the battery pack does not charge properly:
u Check current at receptacle by plugging in a lamp or
other appliance.
u Check to see if receptacle is connected to a light switch
which turns power off when you turn out the lights.
u Move charger and battery pack to a location where the
surrounding air temperature is approximately 65°F
- 75°F (18°- 24°C).
u If charging problems persist, take the tool, battery pack
and charger to your local service center.
u The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily done
previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with no
adverse affect on the battery pack.
u Foreign materials of a conductive nature such as, but
not limited to, steel wool, aluminium foil, or any buildup
of metallic particles should be kept away from charger
cavities. Always unplug the charger from the power supply
when there is no battery pack in the cavity. Unplug charger
before attempting to clean.
u Do not freeze or immerse charger in water or any other
liquid.
Warning! Do not allow any liquid to get inside charger. Never
attempt to open the battery pack for any reason.
If the plastic housing of the battery pack breaks or cracks,
return to a service center for recycling.
u
Charger Diagnostics (Fig.B)
ENGLISH
Bad Battery
If you see a bad battery blink pattern, do not continue
to charge this battery. Return it to a service center or a
collection site for recycling.
Hot/Cold Pack Delay
When the charger detects a battery pack that is too hot
or too cold, it automatically starts a Hot/Cold Pack Delay,
suspending charging until the battery pack has reached an
appropriate temperature. The charger then automatically
switches to the pack charging mode. This feature ensures
maximum battery pack life. A cold battery pack will charge at a
slower rate than a warm battery pack. The pack will charge at
that slower rate throughout the entire charging cycle and will
not return to maximum charge rate even if the pack warms.
Installing and removing the battery pack from the
tool
To install battery pack (Fig. C)
u Insert battery (4) into tool foot until an audible click is
heard (Figure. C)
u Ensure battery pack is fully seated and fully latched into
position.
To remove battery pack (Fig.D)
u Depress the battery release button (4a) as shown in figure
D and pull battery pack (4) out of tool foot.
Assembly
Warning! Before assembly, make sure that the tool is
switched off and the battery is removed.
Fitting sanding mesh (Fig. E)
u
u
Hold the tool with the sanding base facing upwards.
Place the sanding mesh (6) onto the sanding base, making sure that the holes in the sheet line up with the holes
in the base.
Fitting sanding sheets (Fig. F - Optional accessory)
Detach the two additional diamond-shaped tips (8) from
the sanding sheet (7).
The diamond-shaped tip (8) can be reversed and replaced
when worn.
u When the front part of the tip (8) is worn, detach it from the
sheet, reverse it and press it onto the sanding base again.
u When the whole tip is worn, remove it from the sanding
base and fit a new tip.
For optimal dust collection, ensure the correct type of sanding
paper is used.
u
Refer to the indicators in figure B for the charge status of the
battery pack.
8
(Original instructions)
ENGLISH
Replacing diamomnd shaped tip (Fig. G)
u
u
Fitting and removing the dust cassette (Fig. H)
u
u
Slide the dust cassette (2) onto the connector (2a) and
make sure that it is securely located.
To remove the dust casette, pull it to the rear and away
from the rear end of the tool.
VDC
18
Capacity
Ah
2.0
1
Charger
Warning! Let the tool work at its own pace. Do not overload.
Switching on and off
u
Voltage
Type
Use
u
FMC687L
Battery
Replace the diamond shaped tip (9).
Replace and tighten screw (10).
To switch the tool on, depress the on/off switch (1) at the
forward position I.
To switch the tool off, depress the on/off switch (1) at the
back position O.
90611165
230
Input voltage
VAC
Output voltage
VDC
18
mA
2000
Current
LpA (sound pressure) 68 dB(A), Uncertainty (K) 3 dB(A)
LWA (sound power) 79 dB(A), Uncertainty (K) 3 dB(A)
Vibration total values (triax vector sum) according to EN 60745:
Vibration emission value (main handle) (ah) 5,9 m/s2, uncertainty (K) 1,5 m/s2
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance, switch off and
unplug the tool or remove the battery pack.
u Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Protecting the environment
Vibration emission value (aux. handle) (ah) 7,3 m/s2, uncertainty (K) 1,5 m/s2
EC declaration of conformity
%
MACHINERY DIRECTIVE
FMCW210 - Sander
Stanley Europe declares that these products described under
"technical data" are in compliance with:
2006/42/EC, EN60745-1:2009+A11:2010, EN60745-24:2009+A11:2011
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
These products also comply with Directive 2014/30/EU and
2011/65/EU. For more information, please contact Stanley
Fat Max at the following address or refer to the back of the
manual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of Black & Decker.
Technical data
FMCW210
18
Input voltage
Vdc
Oscillations (no load)
min-1
12000
Orbits (no load)
min-1
12000
Sanding base surface
mm2
8866
Weight
kg
9
0.88
R. Laverick
Director of Engineering
Stanley Europe, Egide Walschaertsstraat14-18,
2800 Mechelen, Belgium
23/08/2017
ENGLISH
(Original instructions)
Australia & New Zealand
St
Stanley Black & Decker
www.blackanddecker.com.au
www.blackanddecker.co.nz
Tel.1800 338 002 (Aust) or Tel. 0800 339 258 (NZ)
10
N597325
04/2018
Download PDF

advertising