BDCSFS30 | Black&Decker BDCSFS30 CORDLESS SCREWDRIVER Type H1 instruction manual

www.blackanddecker.co.uk
BDCSFS30
3
8
6a
6
2
4
5
7
3
A
1
B
1
6
C
4
D
5
7a
2
2
7
E
2
F
3
ENGLISH
(Original instructions)
Intended use
Your BLACK+DECKER BDCSFS30 storage screwdriver with
flashlight has been designed for screwdriving applications.
This tool is intended for consumer use only.
Safety instructions
General power tool safety warnings
@
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
4
(Original instructions)
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
h. Do not let familiarity gained from frequent use of tools
allow you to become complacent and ignore tool
safety principles. A careless action can cause severe
injury within a fraction of a second.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool.
e.
f.
g.
h.
Power tools are dangerous in the hands of untrained
users.
Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasing
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
5. Battery tool use and care
a. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
b. Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
c. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws, or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
d. Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
e. Do not use a battery pack or tool that is damaged or
modified. Damaged or modified batteries may exhibit
unpredictable behaviour resulting in fire, explosion or risk
of injury.
f. Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or temperature
above 265º F may cause explosion.
g. Follow all charging instructions and do not charge the
battery pack or tool outside the temperature range
specified in the instructions. Charging improperly or at
temperatures outside the specified range may damage the
battery and increase the risk of fire.
ENGLISH
6.Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
b. Never service damaged battery packs. Service of
battery packs should only be performed by the
manufacturer or authorised service providers.
Additional power tool safety warnings
@
Warning! Additional safety warnings for screwdrivers and impact wrenches
Hold power tool by insulated gripping surfaces, when
performing an operation where the fastener may
contact hidden wiring. Fasteners contacting a "live" wire
may make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
u Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
u The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those
recommended in this instruction manual may present a
risk of personal injury and/or damage to property.
u
Safety of others
Never allow children, persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge or people unfamiliar with these instructions to
use the machine, local regulations may restrict the age of
the operator.
u Never operate the machine while people, especially
children, or pets are nearby.
u
@
Additional power tool safety warnings
Warning! Additional safety warnings for torches
Never ttempt to remove or replace parts other than those
specified in this manual.
u Do not operate without the lens in place or with a
damaged lens.
u Never look directly into the light or shine the light into
another persons eyes.
u
@
Warning! Fire hazard. Do not operate worklight
or charger near flammable liquids or in gaseous
or explosive atmospheres. Internal sparks may
ignite fumes causing opersonal injury.
5
ENGLISH
(Original instructions)
Do not expose light or charger to wet or damp areas. Do
not expose light or charger to rain or snow.
u Do not wash light or charger with water or allow water to
get inside light or charger. Do not submerge light in water
at any time.
u
@
Caution! When not in use, place the tool on
its side on a stable surface where it will not
cause a tripping or falling hazard. Some tools
with large battery packs will stand upright on the
battery pack but may be easily knocked over.
u Never view directly with optical instruments into the light
source.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving parts.
u Injuries caused when changing any parts, blades or accessories.
u Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured in
accordance with a standard test method provided by EN62841
and may be used for comparing one tool with another. The
declared vibration emission value may also be used in a
preliminary
assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
6
(Original instructions)
Labels on tool
The following symbols, along with the date code, are shown
on the tool:
:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Additional safety instructions for batteries and
chargers
Batteries
u Never attempt to open for any reason.
u Do not expose the battery to water.
u Do not store in locations where the temperature may
exceed 40 °C.
u Charge only at ambient temperatures between 10 °C and
40 °C.
u Charge only using the charger provided with the tool.
u When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
p
Do not attempt to charge damaged batteries.
Chargers
u Use your BLACK+DECKER charger only to charge the
battery in the tool with which it was supplied. Other batteries could burst, causing personal injury and damage.
u Never attempt to charge non-rechargeable batteries.
u Have defective cords replaced immediately.
u Do not expose the charger to water.
u Do not open the charger.
u Do not probe the charger.
$
+
The charger is intended for indoor use only.
u
This tool includes some or all of the following features.
1. On/off trigger switch
2. Forward/reverse slider
3. Bit holder
4. Flashlight
5. Flashlight button
6. Charger connector
7. Storage Compartment
Charging tool (fig.A)
The battery needs to be charged before first use and whenever it fails to produce sufficient power on jobs that were easily
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning! Only use the charger provided to charge the tool.
u To charge the battery, insert the charger plug (6a) into the
connector (6).
u Plug in the charger.
u Leave the tool connected to the charger for 10 hours.
The charger may hum and become warm while charging; this
is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging temperature: approx. 24 °C.
Fitting and removing a screwdriver bit or socket
(fig. B)
Warning! Make certain the tool is locked to prevent switch
actuation before installing or removing accessories.
u To fit a screwdriver bit (8), push it into the bit holder (3)
until it locates.
u To remove a screwdriver bit, pull it straight from the bit
holder.
Use
Read the instruction manual before use.
Electrical safety
#
Features
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on the
rating plate. Never attempt to replace the charger
unit with a regular mains plug.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Warning! Let the tool work at its own pace. Do not overload.
Using the flashlight (fig. C)
Press the flashlight button (5) to operate the flashlight (4).
u Press flashlight button (5) again to turn off the flashlight
(4).
u
Switching on and off (fig. D)
u
u
To operate the tool, press and hold the trigger switch (1).
To switch the tool off, release the trigger switch (1).
Selecting the direction of rotation (fig. E)
ENGLISH
To select forward rotation, push the forward/reverse slider
(2) to the right.
u To select reverse rotation, push the forward/reverse slider
(2) to the left.
u To lock the tool, set the forward/reverse slider (2) into the
centre position.
u
Using the storage compartment (fig. F)
The unit is supplied with a removable storage compartment
(7) for storing drill and driver bits, screws, wall plugs etc.
u Slide the storage compartment into the grooves located in
the base of the handle as shown in figure F.
u Reverse this procedure to release the storage compartment from the driver.
How to open/close storage compartment (fig. F)
The storage compartment (7) can be opened by flipping the
clasp (7a) and raising the lid as shown in figure F.
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
u Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u Regularly tap bit holder to remove any dust from the
interior.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste..
Products and batteries contain materials that can be recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
For tightening screws and drilling pilot holes, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
7
Technical data
BDCSFS30 H1
Voltage
VDC
3.6
No-load speed
Min-1
180
Max. torque
Nm
5.5
(PTI Rating)
Battery Type
Li-Ion
Battery capacity
Weight
Ah
1.5
kg
0.35
Black & Decker declares that these products described under
"technical data" are in compliance with:
2006/42/EC, EN62841-1:2015 , EN62841-2-2:2014.
These products also comply with directive
2014/30/EU and 2011/65/EU.
For more information, please contact Black & Decker at the
following address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of Black & Decker.
Ray Laverick
Director of Engineering
Black & Decker Europe, 210 Bath Road, Slough,
Berkshire, SL1 3YD
United Kingdom
17/05/2017
9062787*-01
Charger
Input Voltage
VAC
100 - 240
Output Voltage
VDC
15
Current
mA
150
Approx. charge time
Hours
10
Level of sound pressure according to EN 62841:
Sound pressure (LpA) 53 dB(A), uncertainty (K) 3 dB(A)
Sound power (LWA) 64 dB(A), uncertainty (K) 3 dB(A)
Vibration total values (triax vector sum) according to EN 62841:
Screwdriving without impact (ah, IS) 0.3 m/s2, uncertainty (K) 1.5 m/s2
EC declaration of conformity
%
MACHINERY DIRECTIVE
BDCSFS30 Storage screwdriver
Guarantee
Black & Decker is confident of the quality of its products and
offers consumers a 24 month guarantee from the date
of purchase. This guarantee is in addition to and in no way
prejudices your statutory rights. The guarantee is valid within
the territories of the Member States of the European Union
and the European Free Trade Area.
To claim on the guarantee, the claim must be in accordance
with Black & Decker Terms and Conditions and you will need
to submit proof of purchase to the seller or an authorised repair agent. Terms and conditions of the Black & Decker 2 year
guarantee and the location of your nearest authorised repair
agent can be obtained on the Internet at www.2helpU.com, or
by contacting your local Black & Decker office at the address
indicated in this manual.
Please visit our website www.blackanddecker.co.uk to register
your new Black & Decker product and receive updates on new
products and special offers.
Australia
Black & Decker (Australia) Pty. Ltd.
20 Fletcher Road, Mooroolbark,
Victoria, 3138
Tel. Fax
03-8720 5100
03-9727 5940
New Zealand
Black & Decker
5 Te Apunga Place
Mt Wellington
Aukland 1060
Tel. Fax
+64 9 259 1133
+64 9 259 1122
United Kingdom &
Republic Of Ireland
www.blackanddecker.co.uk
emeaservice@sbdinc.com
Black & Decker
210 Bath Road
Slough, Berkshire SL1 3YD
Tel. Fax
01753 511234
01753 512365
N537515 REV-0
05/2017
Download PDF

advertising