CUA525BHA | Black&Decker CUA525BHA STICK-VAC Type H1 instruction manual

www.blackanddecker.com.au
www.blackanddecker.co.nz
CUA525BH
CUA525BHP
CUA525BHA
3
3
2
1
11
3a
5
10
12
3b
4
5a
6
8
2a
9
12a
7
13
7a
14
15
16
22a
2
17
3
1
11
A
5
12b
12
5
10
9
12b
12
13
C
B
3
9
10
3
D
3a
9a
4
3b
E
3
9
15
14
14a
15
4
15
14b
F
G
18
18a
H
J1
J2
J3
J4
7
J1a
J5
I
4
J6
J
6a
19
5a
6
K
6
L
N1
N2
5
19
5a
M
N
20
20
12
O
5a
5a
P
5
21
22
5a
6a
19
5a
Q
R
5b
23
5c
22
22a
S
T
25
U
6
24
23
25
26
23
V
(Original instructions)
W
ENGLISH
X
2a
2
Y
Intended use
Your BLACK+DECKER CUA525BH, CUA525BHP and
CUA525BHA multi power vacuum cleaners have been
designed for vacuum cleaning purposes. These appliance are
intended for household use only.
Read all of this manual carefully
before operating the appliance.
Safety instructions
@
Warning! Read all safety
warnings and all instructions.
Failure to follow the warnings
and instructions listed below may
result in electric shock, fire and/or
serious injury.
u The intended use is described in this
manual. The use of any accessory
or attachment or the performance
of any operation with this appliance
other than those recommended in this
instruction manual may present a risk
of personal injury.
u Retain this manual for future
reference.
Using your appliance
Do not use the appliance to pick up
liquids or any materials that could
catch fire.
u Do not use the appliance near water.
u Do not immerse the appliance in water.
u Never pull the charger lead to
disconnect the charger from the
socket. Keep the charger lead away
from heat, oil and sharp edges.
u
7
ENGLISH
u
(Original instructions)
This appliance can be used by
children aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or
lack of experience and knowledge
if they have been given supervision
or instruction concerning use of
the appliance in a safe way and
understand the hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made by
children without supervision.
Inspection and repairs
Before use, check the appliance for
damaged or defective parts. Check for
breakage of parts, damage to switches
and any other conditions that may affect
its operation.
u Do not use the appliance if any part is
damaged or defective.
u Have any damaged or defective parts
repaired or replaced by an authorized
repair agent.
u Regularly check the charger lead for
damage. Replace the charger if the
lead is damaged or defective.
u Never attempt to remove or replace
any parts other than those specified in
this manual.
u
u
When not in use, the appliance should
be stored, fully charged, in a dry place.
Children should not have access to
stored appliances.
Residual risks
Additional residual risks may arise when
using the tool which may not be included
in the enclosed safety warnings. These
risks can arise from misuse, prolonged
use etc.
Even with the application of the relevant
safety regulations and the implementation of safety devices, certain residual
risks can not be avoided.
These include:
u Injuries caused by touching any
rotating/moving parts.
u Injuries caused when changing any
parts, blades or accessories.
u Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
u Impairment of hearing.
u Health hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
specific voltage. Always check that the
mains voltage corresponds to the voltage
After use
on the rating plate.
u Unplug the charger before cleaning the
Warning! Never attempt to replace the
charger or charging base.
charger unit with a regular mains plug.
Additional safety instructions
8
(Original instructions)
Use your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
u Never attempt to charge nonrechargeable batteries.
u If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
u Do not expose the charger to water.
u Do not open the charger.
u Do not probe the charger.
u The appliance/battery must be
placed in a well ventilated area when
charging.
u
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#
$
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+
S010Q 23 / SSC-230040XX
Read all of this manual carefully before
using the appliance
Only use with charger S010Q 23 /
SSC-230040XX
ENGLISH
3. Handle / wand
3a. Flexible tube port
3b. Tube extension latch
4. Extendable crevice tool
5. Hand held vac
5a. Dust bowl
6. Dust bowl lid
7. Charging base
7a. Accessory holder
8. Dust bowl lid hinge
9. Hose connector
10. Flexible hose
11. Handle / wand release button
12. Chassis
12a.Light
13. Chassis hose port
14. Floor head
15. 3-in-1 Accesssory tool
16. Pet crevice tool (CUA525BHP only)
17. Long brush tool (CUA525BHA only)
22a. Scent disc (CUA525BHP only)
Use
Switching on and off (Fig. A)
To switch on, press the on/off switch (1).
Unit starts in mid performance setting. Performance can
be adjusted using power control slider (J2) Left = min
Right = max (as seen when in use from above).
u To switch off, press the on/off switch (1).
Note: Use the unit in high speed mode with beater bar
switched on for carpet. Use the unit in low speed mode with
beater bar switched off for hard wood and laminate flooring.
Note: The unit has an intuitve ‘standby’ mode that allows it
to remember the last settings applied for a few minutes upon
starting up.
Note: If leaving the appliance when in use, position the upright
unit, in such a way that any inadvertent fall would contact a
wall or corner and otherwise be away from people and pets.
u
u
Control panel (Fig. J)
The unit is equipped with a smarttech control panel providing
Intelligent sensor technology for a more intuitive cleaning
experience.
The features incorporated are:
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
2a.Carrying strap
9
ENGLISH
(Original instructions)
u
u
J1 FLOORSENSOR Touch Button
Intelligent floor sensor technology increases suction on carpets and
switches to Economy Mode for lighter tasks, such as hard floor cleaning,
thus optimising the battery run time this feature is active when the LED
(J1a) is lit. In order to maximise runtime on all surfaces, switch this
feature off by touching area (J1).
Extend the crevice tool (4) as shown in figure E, until it
clicks in place.
To retract the crevice tool (4) press the tube extension
latch (3b) allowing it to return to its normal position.
Using the 3-in-1 accessory tool (Fig. F)
u
u
J2 Power contol Touch Slider
Touch button panel allows you to control the level of power to the unit
from minimum to maximum by sliding finger along this area.
The 3-in-1 handle / wand (15) has three configurations.
1. Brush mode.
2. Small crevice mode.
3. Upholstery mode.
The 3-in-1 handle / wand can be fitted either directly to the
hose connector 9 or to the extendable crevice tool (4) as
shown in figure F.
Removing and clearing the beater bars
(Fig. G, H)
To remove the beater bar cassette (14a) from the floor
head (14) Depress the release button (14b) as shown in
figure G.
u The beater bar (18) can now be removed.
The end pieces are also removable allowing you to clear
the brushes from any hair or other debris that may have
accumulated as shown in figure H.
Note: If an object gets caught in the beater bar it automatically
stops. Turn the unit off, remove object and continue.
Note: The CUA525BHP unit is supplied with a specialised pet
beater bar (18a) for cleaning pet hairs etc.
u
J3 Beater bar Touch Button
Allows you to turn the beater bar function on and off.
J4 Power indicator
Allows you to monitor the level of power being used.
J5 BATTERYSENSOR Indicator
The LED battery indicator displays the remaining charge and warns you
when the battery is low. The final LED will flash continuously when there
is only 1 minute of runtime remaining. All LEDs will flash when the unit is
discharged.
J6 FILTERSENSOR
Smart sensor technology automatically detects (the symbol will light red)
when the filter becomes clogged and needs to be cleaned.
Note: The FILTERSENSOR LED will flash and the unit will
automatically shut down when there is any obstruction in the
flexible hose or filters which is causing the motor to overheat.
Disconnect and remove the blockage immediately.
Charging (Fig. I)
Place the appliance into the charging base (7) as shown in
figure I .
u Plug the charging base (7) into an electrical outlet.
u Switch the electrical outlet on. The LED charging indicator
will flash and increase in sections.
LEDs go out when fully charged.
u The appliance must be charged for 6 hours.
Note: The Charging base is supplied with 2 screws and wall
plugs for securing it to a wall, providing extra stability, as
shown in figure I.
u
Battery Sensor LED Patterns
Battery Fault (All LEDs)
Using the handle / wand (Fig. B, C, D, E)
u
u
u
u
10
Press the handle / wand release button (11) to free the
handle / wand (3) from the chassis (12).
Free the hose connector (9) from the chassis hose port
(13) as shown in figure B.
Press the chassis release button (12b) to release the hand
held vac (5) from the chassis (12) as shown in
figure C.
Connect the hose connector (9) to the flexible tube port
(3a) ensuring that the latch (9a) clicks securely into place
as shown in figure D.
Charger Fault (All LEDs)
Battery Hot (All LEDs)
Battery diagnostics
If the appliance detects a weak battery, the charging indicator
will flash at a fast rate when the power button is activated.
Proceed as follows:
u Plug in the charger. Switch on at the mains.
u Leave the appliance to charge.
(Original instructions)
If the appliance detects a damaged battery, the charging
indicator will flash at a fast rate when the appliance is on
charge. Proceed as follows:
u Take the appliance and the charger to be tested at an
authorised services centre.
Note: It may take as long as 60 minutes to determine that
the battery is defective. If the battery is too hot or too
cold, the LED will alternately blink, fast and slow, one
flash at each speed and repeat.
Emptying the dust bowl (Fig. K, L, N)
u
u
Holding the unit over a suitable waste receptacle, press
the dust bowl release button (6a) to release the dust bowl
lid (6) as shown in figure K.
Push the compacting handle (19) down to empty the
contents of the dust bowl (5a) as shown in figure L.
Compacting the contents of the dust bowl
(Fig. M, N)
u
With the dust bowl lid (6) closed, push the compacting
handle down to compact the contents of the dustbowl (5a)
to maximise dust collection as shown in figure N.
N1 = Before compacting. N2 = After compacting.
Releasing the dust bowl (Fig. O, P)
Note: The dust bowl can be released either from the unit while
it is in chassis mode, as shown in figure O, or when being
used in the lift away canister vac mode, as shown in figure P.
u Press the dust bowl release lever (20) down to release the
dust bowl.
u Free the dust bowl (5a) from the lift away canister vac (5).
u Using the dust bowl handle (21) and holding the unit over
a suitable waste receptacle, press the dust bowl release
button (6a) to release the dust bowl lid (6) and push the
compacting handle (19) down to empty the contents of the
dust bowl (5a) as shown in figure Q .
Cleaning the dust bowl filters (Fig. R,S,T)
Press the dust bowl release lever (20) down to release the
dust bowl as shown in figure O.
u Lift the filter assembly (22) from the dust bowl (5a) by
rotating anti clockwise as shown in figure R.
Note: The CUA525BHP unit pre filter is supplied with a scented disc in a foil wrapper (22a) which can be attached allowing
for a pleasing odour to be released when the appliance is in
use.
u The filter (23) can now be lifted out of the pre filter (22) as
shown in figure T.
u The dust bowl can be seperated into two parts, (5b) and
(5c), for a more thorough cleaning as shown in figure S.
u Rinse out the dust-bowl with warm soapy water.
u Wash the filters with warm soapy water (Fig. W, X).
u
u
u
u
ENGLISH
Make sure the filters are dry
Refit the filters into the appliance and ensure that they are
correctly seated.
Close the dust-bowl (5a). Reconnect to the lift away
canister vac making sure the release latch (20) clicks into
place.
Cleaning the hand held vac exhaust filters (Fig. U,
V)
Lift off the filter access panel (23), Exposing the filter
chamber (25).
u The filter (24) can now be removed for cleaning.
Note: The CUA525BHA unit is equipped with a HEPA filter
(26) to aid in protection from allergies.
u Both types of filters can be cleaned with warm soapy
water (Fig. W, X).
u
Carrying strap (Fig. Y)
A carrying strap (2a) is supplied to allow easier utilisation of
the hand held vac. This is easily connected to the handle (2)
via a velcro fastener as shown in figure Y.
Maintenance
Warning! Before performing any maintenance or cleaning on
the appliance, unplug the appliance.
From time to time wipe the appliance with a damp cloth.
Do not use any abrasive or solvent-based cleaner. Do not
immerse the appliance in water.
Your BLACK+DECKER cordless appliance has been designed
to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon
proper tool care and regular cleaning.
Warning! Before performing any maintenance on cordless
appliances:
u Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u Regularly clean the ventilation slots in your appliance/
charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Replacing the filters
The filters should be replaced every 6 to 9 months and whenever worn or damaged. Replacement filters are available from
your BLACK+DECKER dealer.
CUABF10 - Standard
Filter Kit
Pleated Filter + Foam Exhaust
CUAHF10 - HEPA Kit
HEPA Pleated Filter + HEPA
Exhaust
11
ENGLISH
(Original instructions)
Warning for scented discs.
Cotton linen fragrance.
Wash face, hands and any exposed skin thoroughly
after handling. Wear protective gloves/protective
clothing/eye protection/face protection. If in eyes:
Rinse cautiously with water for several minutes. Re
move contact lenses if present and easy to do.
Continue rinsing. If skin irritation occurs: Get medical advice/attention. Avoid
release into the environment. Do not ingest.
u
u
Remove the old filters as described above.
Fit the new filters as described above.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical Data
CUA525BH
Voltage
V
18
Watt hours
Wh
45
Weight
Kg
3.85
CUA525BHP
CUA525BHA
18
45
3.85
18
45
3.85
Australia & New Zealand
Stanley Black & Decker
www.blackanddecker.com.au
www.blackanddecker.co.nz
Tel.1800 338 002 (Aust) or Tel. 0800 339 258 (NZ)
N619437
12
06/2018
Download PDF

advertising