D25602K | DeWalt D25602K MID SIZE HAMMER Type 2 instruction manual

D25501
D25601
D25602
D25603
D25820
D25831
Final Page Size: 172 x 240 mm
English (original instructions)4
Fig. A
6
11
4
1
10
14
9
2
5
3
D25501, D25820
6
11
5
4
1
10
D25501
19
14
2
9
7
6
5
3
D25820, D25831
D25602, D25603
3
11
5
4
10
14
1
7
8
5
D25831
1
Fig. B
15
12
3
12
3
D25501, D25601, D25602,
D25603, D25820
D25831
8
Fig. C
18
19
D-65510
DEWALT,
Y
GERMAN
IDSTEIN,
lpU.com
www.2he
ALT.eu
www.DEW
13
Service
Lock-On
7
16
16
17
17
D25601
D25602
18
19
13
7
7
16
16
17
17
D25603
2
ce
Brush Servi
7
D25831
Fig. D
Fig. E
6
11
Fig. F
4
4
3
3
D25831
D25501, D25601, D25602,
D25603, D25820
3
English
SDS MAX® COMBINATION & CHIPPING HAMMERS
D25501, D25601, D25602, D25603, D25820, D25831
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make DeWALT one of the most reliable partners for
professional power tool users.
Technical Data
Voltage
UK & Ireland
Type
Power input
Frequency
Single impact energy (EPTA 05/2009)
No load speed
No load beats per-minute
Total drilling range in concrete:
solid bits
core bits
Optimum drilling range in concrete:
solid bits
Chisel positions
Tool holder
Weight
W
Hz
J
min-1
bpm
D25501
230
230/115
2
1100
50
8
490
3300
D25601
230
230/115
2
1250
50
2–8
210-415
1430-2840
D25602
230
230/115
2
1250
50
2–8
210-415
1430-2840
D25603
230
230
2
1250
50
2–8
210-415
1430-2840
D25820
230
230/115
2
1150
50
8
–
2740
D25831
230
230/115
2
1250
50
2–8
–
1430-2840
mm
mm
12–40
40–90
12–45
40–100
12–45
40–100
12–45
40–100
–
–
–
–
mm
18–26
18
SDS Max®
6.15
25–35
18
SDS Max®
6.8
25–35
18
SDS Max®
6.9
25–35
18
SDS Max®
6.95
–
18
SDS Max®
5.8
–
18
SDS Max®
6.1
94
105
3
94
105
3
93
104
3
93
104
3
94
105
3
95
106
3
m/s2
m/s2
18.3
1.8
8.8
1.5
8.7
1.5
8.7
1.5
–
–
–
–
m/s2
m/s2
13.2
1.6
7.2
1.5
6.8
1.5
6.8
1.5
13.2
1.6
8.3
1.5
VAC
VAC
kg
Noise values and vibration values (triax vector sum) according to EN60745-2-6:
LPA(emission sound pressure level)
dB(A)
LWA(sound power level)
dB(A)
K(uncertainty for the given sound level)
dB(A)
Drilling into concrete
Vibration emission value ah, HD =
Uncertainty K =
Chiselling
Vibration emission value ah,Cheq =
Uncertainty K =
The vibration emission level given in this information sheet has been
measured in accordance with a standardised test given in EN60745 and
may be used to compare one tool with another. It may be used for a
preliminary assessment of exposure.
WARNING: The declared vibration emission level represents the
main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the
vibration emission may differ. This may significantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration should also take
into account the times when the tool is switched off or when it is
running but not actually doing the job. This may significantly reduce
the exposure level over the total working period.
Identify additional safety measures to protect the operator from the
effects of vibration such as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
EC-Declaration of Conformity
Machinery Directive
SDS Max® Combination & Chipping Hammers
D25501, D25601, D25602, D25603
DeWALT declares that these products described under Technical Data are
in compliance with:
2006/42/EC, EN60745-1:2009+A11:2010, EN60745-2-6:2010.
D25820, D25831
2000/14/EC Electrical concrete breaker (hand held) m </= 15kg, Annex VIII;
TÜV Rheinland LGA Products GmbH (0197), D-90431 Nürnberg, Germany
Notified Body ID No.: 0197
Level of sound power according to 2000/14/EC (Article 12, Annex III, No. 10;
m </= 15 kg)
LWA (measured sound power level)
LWA (guaranteed sound power level)
4
dB
dB
102
105
English
These products also comply with Directive 2014/30/EU and 2011/65/EU. For
more information, please contact DeWALT at the following address or refer
to the back of the manual.
The undersigned is responsible for compilation of the technical file and
makes this declaration on behalf of DeWALT.
Markus Rompel
Director Engineering
DeWALT, Richard-Klinger-Straße 11,
D-65510, Idstein, Germany
08.03.2017
WARNING: To reduce the risk of injury, read the instruction manual.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal word.
Please read the manual and pay attention to these symbols.
DANGER: Indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury which,
if not avoided, may result in property damage.
Denotes risk of electric shock.
Denotes risk of fire.
General Power Tool Safety Warnings
WARNING: Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in electric shock,
fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
1) Work area safety
a ) Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b ) Do not operate power tools in explosive atmospheres, such as
in the presence of flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c ) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2) Electrical safety
a ) Power tool plugs must match the outlet. Never modify the
plug in any way. Do not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs and matching outlets
will reduce risk of electric shock.
b ) Avoid body contact with earthed or grounded surfaces such as
pipes, radiators, ranges and refrigerators. There is an increased
risk of electric shock if your body is earthed or grounded.
c ) Do not expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
d ) Do not abuse the cord. Never use the cord for carrying, pulling
or unplugging the power tool. Keep cord away from heat,
oil, sharp edges or moving parts. Damaged or entangled cords
increase the risk of electric shock.
e ) When operating a power tool outdoors, use an extension cord
suitable for outdoor use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f ) If operating a power tool in a damp location is unavoidable,
use a residual current device (RCD) protected supply. Use of an
RCD reduces the risk of electric shock.
3) Personal safety
a ) Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power tool
while you are tired or under the influence of drugs, alcohol
or medication. A moment of inattention while operating power tools
may result in serious personal injury.
b ) Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c ) Prevent unintentional starting. Ensure the switch is in the off
position before connecting to power source and/or battery
pack, picking up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools that have the
switch on invites accidents.
d ) Remove any adjusting key or wrench before turning the power
tool on. A wrench or a key left attached to a rotating part of the
power tool may result in personal injury.
e ) Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situations.
f ) Dress properly. Do not wear loose clothing or jewellery. Keep
your hair, clothing and gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught in moving parts.
g ) If devices are provided for the connection of dust extraction
and collection facilities, ensure these are connected
and properly used. Use of dust collection can reduce dustrelated hazards.
4) Power tool use and care
a ) Do not force the power tool. Use the correct power tool for
your application. The correct power tool will do the job better and
safer at the rate for which it was designed.
b ) Do not use the power tool if the switch does not turn it on
and off. Any power tool that cannot be controlled with the switch is
dangerous and must be repaired.
c ) Disconnect the plug from the power source and/or the battery
pack from the power tool before making any adjustments,
changing accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool accidentally.
d ) Store idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool. Power tools are dangerous
in the hands of untrained users.
e ) Maintain power tools. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that
may affect the power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents are caused by
poorly maintained power tools.
f ) Keep cutting tools sharp and clean. Properly maintained cutting
tools with sharp cutting edges are less likely to bind and are easier
to control.
g ) Use the power tool, accessories and tool bits etc., in accordance
with these instructions taking into account the working
conditions and the work to be performed. Use of the power
tool for operations different from those intended could result in a
hazardous situation.
5
English
5) Service
a ) Have your power tool serviced by a qualified repair person
using only identical replacement parts. This will ensure that the
safety of the power tool is maintained.
•
•
Check for damage to the tool, parts or accessories which may have
occurred during transport.
Take the time to thoroughly read and understand this manual prior
to operation.
Additional Safety Instructions for Rotary Hammers
Markings on Tool
• Wear ear protectors. Exposure to noise can cause hearing loss.
• Use auxiliary handle 3 , if supplied with the tool. Loss of control can
cause personal injury.
• Hold power tool by insulated gripping surfaces, when performing
an operation where the cutting accessory may contact hidden
wiring or its own cord. Cutting accessory contacting a “live” wire
may make exposed metal parts of the power tool “live” and could
give the operator an electric shock.
WARNING: We recommend the use of a residual current device with a
residual current rating of 30mA or less.
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
In spite of the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks cannot be avoided.
These are:
• Impairment of hearing.
• Risk of personal injury due to flying particles.
• Risk of burns due to accessories becoming hot during operation.
• Risk of personal injury due to prolonged use.
Clutch Setting 80 Nm is designed for higher
torque applications.
Clutch Setting 40 Nm is designed for most drilling applications.
Residual Risks
Red service indicator LED. For detailed description see under
Service Indicator LED's.
Yellow service indicator LED. For detailed description see under
Service Indicator LED's.
Electrical Safety
The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.
Your DeWALT tool is double insulated in accordance with
EN60745; therefore no earth wire is required.
WARNING: 115 V units have to be operated via a fail-safe isolating
transformer with an earth screen between the primary and
secondary winding.
If the supply cord is damaged, it must be replaced by a specially prepared
cord available through the DeWALT service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Using an Extension Cable
An extension cord should not be used unless absolutely necessary. Use an
approved extension cable suitable for the power input of your charger (see
Technical Data). The minimum conductor size is 1.5 mm2; the maximum
length is 30 m.
When using a cable reel, always unwind the cable completely.
Package Contents
The package contains:
1 Rotary hammer (D25501, D25601, D25602, D25603)
or
1 Chipping hammer (D25820, D25831)
1 Side handle
1 Kitbox (K-models only)
1 Instruction manual
6
Visible radiation. Do not stare into light.
Date Code Position (Fig. A)
The date code 14 , which also includes the year of manufacture, is printed
into the housing.
Example:
2017 XX XX
Year of Manufacture
Description (Fig. A, B)
WARNING: Never modify the power tool or any part of it. Damage or
personal injury could result.
1 Trigger switch (D25501, D25601, D25602, D25603)
On/off rocker switch (D25820, D25831)
2 Lock-on slider (D25601, D25602, D25603)
3 Side handle
4 Main handle
5 Active vibration control (D25601, D25602, D25603, D25831)
6 Mode selector switch
7 Electronic speed and impact control dial (D25601, D25602, D25603,
D25831)
8 Side handle knob (D25831)
9 Side handle clamp (D25501, D25601, D25602, D25603, D25820)
10 Tool holder
11 Locking sleeve
Intended Use
The D25501, D25601, D25602, D25603 rotary hammers have been designed
for professional rotary drilling and chipping applications.
The D25820, D25831 chipping hammers have been designed for
professional chipping, chiselling and demolition applications.
DO NOT use under wet conditions or in the presence of flammable liquids
or gases.
These hammers are professional power tools.
English
DO NOT let children come into contact with the tool. Supervision is
required when inexperienced operators use this tool.
• Young children and the infirm. This appliance is not intended for use
by young children or infirm persons without supervision.
• This product is not intended for use by persons (including children)
suffering from diminished physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are supervised by a person
responsible for their safety. Children should never be left alone with
this product.
D25831
The red service indicator LED 16 lights up if there is a fault with the
tool or the brushes have completely worn out (refer to Brushes under
Maintenance).
Soft Start Feature
ASSEMBLY AND ADJUSTMENTS
D25601, D25602, D25603, D25831
The soft start feature allows the tool to accelerate slowly, thus preventing
the drill bit from walking off the intended hole position when starting.
The soft start feature also reduces the immediate torque reaction
transmitted to the gearing and the operator if the hammer is started with
the drill bit in an existing hole.
Electronic Speed and Impact Control (Fig. A, C)
D25601, D25602, D25603, D25831
The electronic speed and impact control 7 offers the following advantages:
-- use of smaller accessories without risk of breakage;
-- minimised break-out when chiselling or drilling in soft or brittle
materials;
-- optimal tool control for precise chiselling.
Torque Limiting Clutch
WARNING: The user must always maintain a firm grip on the tool
when in operation.
The torque limiting clutch reduces the maximum torque reaction
transmitted to the operator in case of jamming of a drill bit. This feature also
prevents the gearing and electric motor from stalling.
NOTICE: Always turn the tool off before changing torque control
settings or damage to tool may result.
Complete Torque Control (CTC) (Fig. C) D25602
Complete Torque Control (CTC) offers the user a two-stage mechanical
clutch with adjustable torque options. Adjusting the torque provides
increased control for various applications.
The low setting (40 Nm) allows the tool to operate at a reduced torque
level increasing control for many solid drilling applications. The high setting
(80 Nm) is available for more demanding applications such as core drilling
and the use of large diameter solid bits.
Refer to Setting the Two Stage Mechanical Clutch for more information.
Ultimate Torque Control (UTC) (Fig. C) D25603
In addition to the two-stage mechanical clutch, Ultimate Torque Control
(UTC) offers increased user comfort and safety through an on-board,
anti-rotation technology capable of detecting if the user loses control
of the hammer. When a jam is detected, the torque and speed are
reduced instantly. This feature prevents self rotation of the tool reducing the
occurrence of wrist injuries.
Service Indicator LEDs (Fig. A, C)
D25601, D25602, D25603, D25831
The yellow brushwear indicator LED 17 lights up when the carbon brushes
are nearly worn out to indicate that the tool needs servicing within the next
8 hours of use.
D25601, D25602, D25603
The red service indicator LED 16 lights up if the lock-on button 2 is
used in any mode except the chipping mode. On models fitted with
Ultimate Torque Control (UTC), the red LED indicator 16 lights up if the
anti-rotational device is activated. The red indicator starts to flash if there
is a fault with the tool or the brushes have completely worn out (refer to
Brushes under Maintenance).
Fully Vibration-Dampened Main Handle (Fig. A)
D25601, D25602, D25603, D25831
The dampers in the main handle 4 absorb the vibrations transmitted to
the user. This improves user comfort during the operation.
WARNING: To reduce the risk of serious personal injury,
turn tool off and disconnect tool from power source before
making any adjustments or removing/installing attachments
or accessories. Be sure the trigger switch is in the OFF position. An
accidental start-up can cause injury.
Fitting the Side Handle (Fig. B)
The side handle 3 clamps to the mounting area 12 of the gear case and
may be rotated 360˚ to permit right- or left-hand use. The side handle
must be tightened sufficiently to resist the twisting action of the tool if the
accessory binds or stalls. Be sure to grip the side handle at the far end to
control the tool during a stall.
To loosen side handle, rotate counterclockwise.
Inserting and Removing SDS Max® Accessories
(Fig. A, D)
This machine uses SDS Max® bits and chisels (refer to the inset in figure DB
for a cross-section of an SDS Max® bit shank).
1. Clean the bit shank.
2. Pull back the locking sleeve 11 and insert the bit shank.
3. Turn the bit slightly until the sleeve snaps into position.
4. Pull on the bit, to check if it is properly locked. The hammering function
requires the bit to be able to move axially several centimetres when
locked in the tool holder.
5. To remove a bit pull back the tool holder locking sleeve/collar 11 and
pull the bit out of the tool holder 10 .
Selecting the Operating Mode (Fig. A)
Hammerdrilling:
D25501, D25601, D25602, D25603
for concrete, brick, stone and masonry drilling operations.
Hammering only:
D25501, D25601, D25602, D25603, D25820, D25831
for chiselling and demolition applications. In this mode the tool
can also be used as a lever to free a jammed drill bit.
1. To select the operating mode, rotate the mode selector switch 6 until
it points to the symbol of the required mode.
It may be neccessary to twist the tool holder 10 slightly to allow the
mode selector switch 6 to pass the
position.
2. Check that the mode selector switch 6 is locked in place.
Indexing the Chisel Position (Fig. E)
D25501, D25601, D25602, D25603, D25820,
D25831
The chisel can be indexed and locked into 18 different positions.
1. Rotate the mode selector switch 6 until it points towards the
position.
2. Rotate the chisel in the desired position.
3. Set the mode selector switch 6 to the “hammering only” position.
4. Twist the chisel until it locks in position.
7
English
Setting the Electronic Speed and Impact Control Dial
(Fig. A, C)
D25601, D25602, D25603, D25831
Turn the dial 7 to the desired level. Turn the dial upwards for higher
speed and downwards for lower speed. The required setting is a matter of
experience, e.g.
• when chiselling or drilling in soft, brittle materials or when minimum
break-out is required, set the dial to a low setting;
• when breaking or drilling in harder materials, set the dial to a
high setting.
Proper Hand Position (Fig. F)
WARNING: To reduce the risk of serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of serious personal injury, ALWAYS hold
securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the side handle 3 , with the
other hand on the main handle 4 .
Switching On and Off (Fig. A)
D25501, D25601, D25602, D25603
Setting the Two Stage Mechanical Clutch (Fig. C)
To turn the tool on, depress the trigger switch 1 .
To stop the tool, release the trigger switch.
D25602, D25603
D25601, D25602, D25603
NOTICE: Always turn the tool off before changing torque control
settings or damage to the tool may result.
Move the torque control lever 13 to setting 40 Nm or 80 Nm as needed
for application.
• Clutch Setting 40 Nm 18 is designed for most drilling applications and
is designed to easily clutch out when the drill bit encounters re-bar or
other foreign substances.
• Clutch Setting 80 Nm 19 is designed for higher torque applications
such as core-bits and deep hole drilling and is designed to clutch out at
a higher torque threshold.
NOTE: If it is not possible to select position 80 Nm, run the unit under load
and try again.
Each time the tool is plugged in, it will automatically default to clutch
setting 1 into clutch setting 40 Nm 18 , the most sensitive setting.
Depth Rod
(Additional Accessory)
1. Push in and hold the depth rod release button on the side handle.
2. Move the depth rod so the distance between the end of the rod and
the end of the bit equals the desired drilling depth.
3. Release the button to lock rod into position. When drilling with the
depth rod, stop when end of rod reaches surface of material.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal injury,
turn tool off and disconnect tool from power source before
making any adjustments or removing/installing attachments
or accessories. Be sure the trigger switch is in the OFF position. An
accidental start-up can cause injury.
WARNING: Tool bits may be hot and gloves should be worn when
changing or removing them to avoid personal injury.
WARNING:
• Be aware of the location of pipework and wiring.
• Apply only a gentle pressure to the tool (approximately 20 kg).
Excessive force does not speed up drilling but decreases tool
performance and may shorten tool life.
• Always hold the tool firmly with both hands and ensure a
secure stance. Always operate the tool with the side handle
properly assembled.
NOTE: Operating temperature is -7˚ to +40˚C (19˚ to 104˚F). Using the tool
outside of this temperature range will decrease the life of the tool.
8
The lock-on slider 2 allows the trigger switch 1 to be locked on in
chiselling mode only. If the lock-on button is activated in drilling mode, as a
feature the tool will switch off automatically.
To turn the tool on, press the trigger switch 1 .
To stop the tool, release the switch.
For continuous operation, press and hold down the switch 1 , slide the
lock-on button 2 upwards and release the switch.
To stop the tool in continuous operation, press the switch briefly
and release it. Always switch off the tool when work is finished and
before unplugging.
D25820, D25831
To turn the tool on, press the on/off rocker switch 1 at the lower part of
the trigger.
To stop the tool, press the on/off rocker switch at the upper part of
the trigger.
Hammerdrilling
To turn the tool on, press the on/off switch 1 .
To stop the tool, release the switch.
Drilling with a Solid Bit (Fig. A)
D25501, D25601, D25602, D25603
1. Insert the appropriate drill bit.
2. Set the mode selector switch 6 to the hammerdrilling position.
3. D25601, D25602, D25603 only: Set the electronic speed and impact
control dial 7 .
4. Fit and adjust the side handle 3 .
5. Mark the spot where the hole is to be drilled.
6. Place the drill bit on the spot and switch on the tool.
7. Always switch off the tool when work is finished and
before unplugging.
Drilling with a Core Bit (Fig. A)
1. Insert the appropriate core bit.
2. Assemble the centerdrill into the core bit.
3. Set the mode selector switch 6 to the hammerdrilling position.
4. D25601, D25602, D25603 only: Turn the electronic speed and impact
control dial 7 to a medium or high speed setting.
5. Fit and adjust the side handle 3 .
6. Place the centerdrill on the spot and switch on the tool. Drill until the
core penetrates into the concrete approximately 1 cm.
7. Stop the tool and remove the centerdrill. Place the core bit back into the
hole and continue drilling.
8. When drilling through a structure thicker than the depth of the core
bit, break away the round cylinder of concrete or core inside the bit at
regular intervals.
To avoid unwanted breaking away of concrete around the hole, first drill
English
a hole the diameter of the centerdrill completely through the structure.
Then drill the cored hole halfway from each side.
9. Always turn the tool off when work is finished and before unplugging.
Chipping and Chiselling (Fig. A)
D25501, D25601, D25602, D25603, D25820,
D25831
Protecting the Environment
Separate collection. Products and batteries marked with this
symbol must not be disposed of with normal household waste.
Products and batteries contain materials that can be recovered or
recycled reducing the demand for raw materials. Please recycle
electrical products and batteries according to local provisions. Further
information is available at www.2helpU.com.
1. Insert the appropriate chisel and rotate it by hand to lock it into one of
18 positions.
2. Set the mode selector switch 6 to the hammering only position.
3. D25601, D25602, D25603, D25831 only: Set the electronic speed and
impact control dial 7 .
4. Fit and adjust the side handle 3 .
5. Turn the tool on and start working.
6. Always turn the tool off when work is finished and before unplugging.
MAINTENANCE
Your DeWALT power tool has been designed to operate over a long period
of time with a minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of serious personal injury,
turn tool off and disconnect tool from power source before
making any adjustments or removing/installing attachments
or accessories. Be sure the trigger switch is in the OFF position. An
accidental start-up can cause injury.
Brushes (Fig. C)
The carbon brushes are not user-serviceable. Take the tool to an authorized
DeWALT repair agent.
The yellow brushwear indicator LED 17 lights up when the carbon brushes
are nearly worn out. After a further 8 hours of use or after the brushes have
completely worn out, the motor will automatically be shut off.
Tool maintenance needs to be carried out as soon as the service
indicator 16 lights up.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of the main housing with dry air
as often as dirt is seen collecting in and around the air vents. Wear
approved eye protection and approved dust mask when performing
this procedure.
WARNING: Never use solvents or other harsh chemicals for cleaning
the non-metallic parts of the tool. These chemicals may weaken the
materials used in these parts. Use a cloth dampened only with water
and mild soap. Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
Optional Accessories
WARNING: Since accessories, other than those offered by DeWALT,
have not been tested with this product, use of such accessories with
this tool could be hazardous. To reduce the risk of injury, only DeWALT
recommended accessories should be used with this product.
Consult your dealer for further information on the appropriate accessories.
9
Belgique et
Luxembourg België
en Luxemburg
DeWALT - Belgium BVBA
Egide Walschaertsstraat 16
2800 Mechelen
Tel: NL 32 15 47 37 63
Tel: FR 32 15 47 37 64
Fax:
32 15 47 37 99
www.dewalt.be
enduser.BE@SBDinc.com
Danmark
DeWALT
Roskildevej 22
2620 Albertslund
Tel:
Fax:
www.dewalt.dk
kundeservice.dk@sbdinc.com
Deutschland
DeWALT
Richard Klinger Str. 11
65510 Idstein
Tel:06126-21-1
Fax:06126-21-2770
www.dewalt.de
infodwge@sbdinc.com
Ελλάς
DeWALT (Ελλάς) Α.Ε.
EΔΡΑ-ΓΡΑΦΕΙΑ : Στράβωνος 7
& Λ. Βουλιαγμένης, Γλυφάδα 166 74, Αθήνα
SERVICE : Ημερος Τόπος 2 (Χάνι Αδάμ) – 193 00 Ασπρόπυργος
Τηλ:00302108981616
Φαξ:00302108983570
www.dewalt.gr
Greece.Service@sbdinc.com
España
DeWALT Ibérica, S.C.A.
Parc de Negocios “Mas Blau”
Edificio Muntadas, c/Bergadá, 1, Of. A6
08820 El Prat de Llobregat (Barcelona)
Tel:
Fax:
934 797 400
934 797 419
www.dewalt.es
respuesta.postventa@sbdinc.com
France
DeWALT
5, allée des Hêtres
BP 30084, 69579 Limonest Cedex
Tel:
Fax:
04 72 20 39 20
04 72 20 39 00
www.dewalt.fr
scufr@sbdinc.com
Schweiz
Suisse
Svizzera
DeWALT
In der Luberzen 42
8902 Urdorf
Tel:
Fax:
044 - 755 60 70
044 - 730 70 67
www.dewalt.ch
service@rofoag.ch
Ireland
DeWALT
Calpe House Rock Hill
Black Rock, Co. Dublin
Tel:00353-2781800
Fax:00353-2781811
www.dewalt.ie
Italia
DeWALT
via Energypark
20871 Vimercate (MB), IT
Tel: Fax: 800-014353
39 039 9590200
39 039 9590313
www.dewalt.it
Nederlands
DeWALT Netherlands BV
Holtum Noordweg 35
6121 RE BORN, Postbus 83, 6120 AB BORN
Tel:
Fax:
31 164 283 063
31 164 283 200
www.dewalt.nl
Norge
DeWALT
Postboks 4613, Nydalen
0405 Oslo
Tel: Fax: 45 25 13 00
45 25 08 00
www.dewalt.no
kundeservice.no@sbdinc.com
Österreich
DeWALT
Werkzeug Vertriebsges m.b.H
Oberlaaerstrasse 248, A-1230 Wien
Tel: Fax: 01 - 66116 - 0
01 - 66116 - 614
www.dewalt.at
service.austria@sbdinc.com
Portugal
DeWALT Limited, SARL
Centro de Escritórios de Sintra Avenida
Almirante Gago Coutinho, 132/134, Edifício 14
2710-418 Sintra
Tel: Fax: 214 66 75 00
214 66 75 80
www.dewalt.pt
resposta.posvenda@sbdinc.com
Suomi
DeWALT
PL 47
00521 Helsinki
Puh: Faksi:
010 400 4333
0800 411 340
www.dewalt.fi
asiakaspalvelu.fi@sbdinc.com
Sverige
DeWALT
Box 94
431 22 Mölndal
Tel:
Fax: 031 68 61 60
031 68 60 08
www.dewalt.se
kundservice.se@sbdinc.com
Türkiye
KALE Hırdavat ve Makina A.Ş.
Defterdar Mah. Savaklar Cad. No:15
Edirnekapı / Eyüp / İSTANBUL 34050 TÜRKİYE
Tel: Faks:
0212 533 52 55
0212 533 10 05
www.dewalt.com.tr
United
Kingdom
DeWALT, 210 Bath Road;
Slough, Berks SL1 3YD
Tel: Fax: 01753-567055
01753-572112
www.dewalt.co.uk
emeaservice@sbdinc.com
Australia
DeWALT
82 Taryn Drive, Epping
VIC 3076 Australia
Tel: Aust 1800 338 002
Tel: NZ 0800 339 258
www.dewalt.com.au
www.dewalt.co.nz
Middle East Africa
DeWALT
P.O. Box - 17164,
Jebel Ali Free Zone (South), Dubai, UAE
Tel: Fax: www.dewalt.ae
Service.MEA@sbdinc.com
70 20 15 10
70 22 49 10
971 4 812 7400
971 4 2822765
N48789703/17
Download PDF

advertising