FMC795B | Stanley FMC795B WET N'DRY VAC instruction manual

1
2
10
8
11
9
6
3
12
4
5
7
5
FMC795B
14
17
15
16
A
7
13
B
1
3
18
5
5
C
D
14
13
15
E
2
18
19
F
(Original instructions)
Intended use
Your Stanley Fat Max FMC795B wet & dry vac has been
designed for wet and dry vacuum cleaning purposes. This
appliances is intended for professional and private, non
professional users.
Read all of this manual carefully
before operating the appliance.
Safety instructions
@
Warning! Read all safety
warnings and all instructions.
Failure to follow the warnings
and instructions listed below may
result in electric shock, fire and/or
serious injury.
ENGLISH
Safety of others
This tool is not intended for use by
persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience
and knowledge, unless they have
been given supervision or instruction
concerning use of the tool by a person
responsible for their safety.
u Children should be supervised to
ensure that they do not play with the
appliance.
u
Inspection and repairs
Before use, check the appliance for damaged or defective parts.
u The intended use is described in this
Check for breakage of parts, damage to
manual. The use of any accessory
switches and any other conditions that
or attachment or the performance
may affect its operation.
of any operation with this appliance
u Do not use the appliance if any part is
other than those recommended in this
damaged or defective.
instruction manual may present a risk
u Have any damaged or defective parts
of personal injury.
repaired or replaced by an authorized
u Retain this manual for future
repair agent.
reference.
u Regularly check the charger lead for
Using your appliance
damage. Replace the charger if the
u Do not use the appliance to pick up
lead is damaged or defective.
liquids or any materials that could
u Never attempt to remove or replace
catch fire
any parts other than those specified in
u Do not immerse the appliance in water.
this manual.
u Never pull the charger lead to
Additional safety instructions
disconnect the charger from the
socket. Keep the charger lead away
After use
from heat, oil and sharp edges.
u Unplug the charger before cleaning.
u
When not in use, the appliance should
be stored in a dry place.
3
ENGLISH
u
(Original instructions)
Children should not have access to
stored appliances.
Residual risks
Additional residual risks may arise when
using the tool which may not be included
in the enclosed safety warnings. These
risks can arise from misuse, prolonged
use etc.
Even with the application of the relevant
safety regulations and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any
rotating/moving parts.
u Injuries caused when changing any
parts, blades or accessories.
u Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
u Impairment of hearing.
u Health hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Batteries (not supplied)
Never attempt to open for any reason.
u Do not expose the battery to water.
u Do not store in locations where the
temperature may exceed 40 °C.
u Charge only at ambient temperatures
between 10 °C and 40 °C.
u Charge only using the charger
provided with the tool.
u If the appliance is to be stored unused
for a long period, the batteries should
be removed.
u
4
u
When disposing of batteries, follow
the instructions given in the section
“Protecting the environment”.
p
Do not attempt to charge damaged batteries.
Chargers (not supplied)
Use your Stanley Fat Max charger only
to charge the battery in the tool with
which it was supplied. Other batteries
could burst, causing personal injury
and damage.
uNever attempt to charge nonrechargeable batteries.
uHave defective cords replaced
immediately.
uDo not expose the charger to water.
uDo not open the charger.
u Do not probe the charger.
u
Electrical safety
Symbols on the charger
$
Read all of this manual carefully before using the
appliance.
The charger is intended for indoor use only.
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Main handle
3. Power head
4. Tank
5. Tank latch
6. Intake port
7. Battery port
8. Vacuum hose
9. Hose clip
10. Side exhaust port
11. Crevice tool
12. Wide nozzle tool
(Original instructions)
Assembly
Attaching vacuum hose (Fig. A)
The vacuum hose (8) will need to be attached to the
vacuum before using the appliance.
u Place the vacuum on a flat, firm surfac
u Unlatch tank latches (5) and remove power head from
the tank. Remove the hose (8) from the tank.
u Align the hose end (13) with the intake port (6) on the
front of the appliance, ensuring the hose alignment lock
(14) is aligned with the arrow (15) on the intake port.
u Insert the hose end into the intake port and twist
clockwise to lock in place.
u Replace power head onto the tank and secure latches.
Note: The power head will only fit onto the tank when th
intake port on the front of the power head and the storage
area for the wide nozzle tool on the tank are aligned as
shown in figure A.
Charging the battery (not supplied)
The battery needs to be charged before first use and whene er it fails to produce sufficient power on jobs that were easily
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging temperature: approx. 24 °C.
Note: The charger will not charge a battery if the cell temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell temperature
warms up or cools down.
u To charge the battery (16), insert it into the charger. The
battery will only fit into the charger in one wa . Do not
force. Be sure that the battery is fully seated in the charger.
u Plug in the charger and switch on at the mains.
The charging indicator will flash continuously (slowly)
The charge is complete when the charging indicator lights
continuously. The charger and the battery can be left connected indefinitely with the LED illuminated. The LED will change
to flashing (charging) state as the charger occasionally tops
up the battery charge.
The charging indicator will be lit as long as the battery is
connected to the plugged-in charger.
u Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indefinitel . The charger will keep the battery
pack fresh and fully charged.
ENGLISH
Charger diagnostics
If the charger detects a weak or damaged battery, the charging indicator will flash red at a fast rate. Proceed as follows
u Re-insert the battery (16).
u If the charging indicators continues flashing at a fast rate,
use a different battery to determine if the charging process
works properly.
u If the replaced battery charges correctly, the original
battery is defective and should be returned to a service
centre for recycling.
u If the new battery gives the same indication as the original
battery, take the charger to be tested at an authorised
service centre.
Note: It may take as long as 60 minutes to determine that
the battery is defective. If the battery is too hot or too cold,
the LED will alternately blink, fast and slow, one flash at each
speed and repeat.
Installing and removing the battery pack (not
supplied) (Fig. B)
Warning! Ensure battery port and terminals are dry and clean
before installing battery pack.
u To install the battery pack (16) into the power head, align
the battery pack with the rails inside the tool’s battery port
(7) until the battery pack is firmly seated in the tool an
ensure that it does not disengage.
u To remove the battery pack from the tool, press the
release button (17) and firmly pull the battery pack out of
the tool handle. Insert it into the charger as described in
the charger section of this manual.
Correct hand position
Warning! To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
u Proper hand position requires one hand on the main
handle (2).
Use
On / Off Switch (Fig. C)
u
u
u
Attach the appropriate accessory to the hose (8).
Insert battery pack.
To turn vacuum on, press the I/O (on/off) button (1).
Dry vacuum cleaning
To empty tank (FIG. D)
The sound of the motor changes and suction is reduced when
the tank is full.
u Turn vacuum off. Remove the battery pack.
5
ENGLISH
u
u
u
u
u
(Original instructions)
Unlatch tank latches (5) and remove power head from
the tank.
Empty contents of tank into suitable container.
Clean or change filter (18). See Filter section of thi
manual.
Inspect vacuum for damage by foreign objects. Contact
the nearest Stanley Fat Max authorized service center for
replacement of damaged or missing parts.
Replace power head (3) onto the tank (4) and latch
securely.
Dry vacuum cleaning
Warning! Do not tilt vacuum when in use.
If vacuum has liquid in the tank it may spill out from the
exhaust port.
Warning! Ensure battery port and terminals are dry and clean
before installing battery pack.
The filter must be removed before using the vacuum t
clean liquids. See Filter section of this manual.
To empty tank
The sound of the motor changes and suction is reduced
when the tank is full.
u Turn vacuum off. Remove the battery pack.
u Unlatch tank latches (5) and remove power head from
the tank.
u Empty contents of tank.
u Inspect vacuum for damage by foreign objects. Contact
the nearest Stanley Fat Max authorized service center for
replacement of damaged or missing parts.
u Dry inside of power head and tank with a clean cloth.
u Replace power head (3) onto the tank (4) and latch
securely.
Filter
Filter care
The wet/dry filter (18) included with this vacuum is a long
life filter. To be effective in minimizing dust recirculation the
filters MUST be installed correctly and in good condition.
Note: A clean filter is the most important factor in the
operation and efficiency of any vacuum. If the filter becomes
clogged beyond cleaning, damaged, or fails to operate
properly, replace only with a reccomended replacement.
To clean or change the filter (Fig. E)
u
u
u
6
Turn vacuum off. Remove the battery pack.
Unlatch the tank latches (5) and remove the power
head from the tank as shown in figure D. Unlock th
filter lock (19) by twisting it counter clockwise. Pull th
filter (18) out to remove it from the power head
Clean the filter by shaking o f excess dust, tapping into
a waste receptacle, then rinsing under running water.
Depending on the condition of the filte , a water wash is
not always required. Do not use a brush to clean filte .
u Reinstall filter and secure the filter lock onto pow
head. Twist the filter lock clockwise and ensure the filt
is locked in place.
u Replace power head onto the tank and secure latches.
Note: Please contact your local service center or visit our
website www.stanley.eu/3 to purchase a filter.
Blower
The blower function can be used to remove debris from
behind small spaces, to dry a damp floo , to blow grass
clippings or leaves from an outside walk, patio, etc.
To use as a blower (Fig. F)
u
u
u
u
Empty the tank following the instructions under the
Vacuum Cleaning section of this manual.
Twist the vacuum hose (2) counter clockwise to remove
from the intake port.
Align the hose end (13) with the side exhaust port (10),
ensuring the hose alignment lock 14 is aligned with the
arrow 15 above the side exhuast port.
Insert the hose end into the side exhaust port and twist
clockwise to lock in place.
Hose and accessory storage
When the vacuum is not in use, remove the battery pack.
The vacuum hose can be wrapped around appliance,
underneath the battery interface, and secured with the
hose clip (7) also located at the back of the vacuum. The two
accessories (crevice tool and wide nozzle) can be stored on
board the vacuum as well.
Troubleshooting guide
Problem
Possible cause
Unit will not start
Battery pack not
installed properly.
Battery pack not
charged.
Internal components
too hot.
Brushes worn out.
Possible Solution
Check battery pack
installation
Check battery pack
charging requirements.
Allow tool to cool down.
Have motor replaced by
an authorized Stanley
Fat Max
service center
Have brushes replaced
by an authorized
Stanley Fat Max
service center
ENGLISH
(Original instructions)
Battery pack will not
charge.
Battery pack not inserted into charger.
Charger not plugged in.
Surrounding air
temperature too hot or
too cold.
Unit shuts off abruptly.
Unit has reduced
suction.
Insert battery pack into
charger until LED
illuminates.
Plug charger into a
working outlet. Refer
to “Important charging
notes” for more details.
Move charger and
battery pack to a
surrounding air
temperature below 10
°C or above 40 °C.
Battery pack has
reached its maximum
thermal limit.
Out of charge. (To
maximize the life of
the battery pack it is
designed to shut off
abruptly when the
charge is depleted.)
Allow battery pack to
cool down.
Tank is full.
Filter is dirty or clogged.
Empty tank.
Clean or replace filte .
Place on charger and
allow to charge.
Technical Data
FMC795B
Voltage
18V
Weight
3.32Kg
Charger
905998** typ.1
906086**typ.1
Input vpltage
VAC
230
230
Output Voltage
VCC
18
18
A
1
min
90 - 240
Current
Approx. charge
time
Battery
2
45 - 120
FMC689L
FMC687L
Voltage
VCC
18
18
18
Capacity
Ah
1.5
2.0
4.0
Li-ion
Li-ion
Type
FMC688L
Li-ion
Maintenance
Your Stanley Fat Max cordless appliance has been designed
to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon
proper tool care and regular cleaning.
Warning! Before performing any maintenance on cordless
appliances:
u Run the battery down completely if it is integral and then
switch off.
u Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u Regularly clean the ventilation slots in your appliance/
charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Australia & New Zealand
St
Stanley Black & Decker
www.blackanddecker.com.au
www.blackanddecker.co.nz
Tel.1800 338 002 (Aust) or Tel. 0800 339 258 (NZ)
Replacing the filters
The filters should be replaced every 6 to 9 months and
whenever worn or damaged. Replacement filters are available
from your Stanley Fat Max dealer. Please visit our website
www.stanley.eu/3
u Remove the old filters as described above
u Fit the new filters as described above
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
7
NXXXXXX
03/2018
Download PDF

advertising