FMCD900 | Stanley FMCD900 HAMMER instruction manual

5
4
3
2
1
7
6
www.stanley.eu
FMCD900
7
9
11
12
7
10
B
A
8
4
6
C
13
5
D
2
14
15
14
5
E
18
17 16
1
15
F
G
2
2
Models FMCD900M1S, FMCD900M2S, FMCD900M2T,
FMCD900B; basic series FMCD900
Intended use
Your Stanley Fat Max, FMCD900 SDS rotary hammer have
been designed for drilling in wood, metal, plastics, and
masonry as well as for screwdriving and light chiselling
applications. These tools are intended for professional and
private, non professional users.
Safety instructions
General power tool safety warnings
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric
shock, fire and/or serious injury.
H
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains
operated (corded) power tool or battery operated (cordless)
power tool.
3
19
20
21
I
22
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way.
3
ENGLISH
b.
c.
d.
e.
f.
(Original instructions)
Do not use any adapter plugs with earthed (grounded)
power tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
4
connected and properly used. Use of dust collection can
reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5.Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional power tool safety warnings
Warning! Additional safety warnings for rotary
and chiselling hammers
Wear ear protectors. Exposure to noise can cause
hearing loss.
u Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
u Hold power tool by insulated gripping surfaces when
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contacting
a "live" wire may make exposed metal parts of the power
u
(Original instructions)
tool "live" and could give the operator an electric shock.
Never use a chisel accessory in rotary mode. The
accessory will bind in the material and rotate the drill.
u Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
u Before drilling into walls, floors or ceilings, check for the
location of wiring and pipes.
u Avoid touching the tip of a drill bit just after drilling, as it
may be hot.
u This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children should be supervised to ensure
that they do not play with the appliance.
u The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those
recommended in this instruction manual may present a
risk of personal injury and/or damage to property.
u Use a face or dust mask whenever the operations may
produce dust or flying particles.
u
Safety of others
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
u Children should be supervised to ensure that they do not
play with the appliance.
u
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving parts.
u Injuries caused when changing any parts, blades or
accessories.
u Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust developed when
ENGLISH
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured in
accordance with a standard test method provided by
EN 60745 and may be used for comparing one tool with
another. The declared vibration emission value may also be
used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the
trigger time.
Labels on tool
The following pictograms are shown on the tool along with the
date code:
f
Warning! To reduce the risk of injury, the
user must read the instruction manual.
Wear ear protectors with rotary hammer drills.
Exposure to noise can cause hearing loss
Additional safety instructions for batteries and
chargers (Not provided with the FMCD900B)
Batteries
u Never attempt to open for any reason.
u Do not expose the battery to water.
u Do not store in locations where the temperature may
exceed 40 °C.
u Charge only at ambient temperatures between 10 °C and
40 °C.
u Charge only using the charger provided with the tool.
u When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
p
Do not attempt to charge damaged batteries.
5
ENGLISH
(Original instructions)
Chargers
u Use your Stanley FatMax charger only to charge the
battery in the tool with which it was supplied.
Other batteries could burst, causing personal injury and
damage.
u Never attempt to charge non-rechargeable batteries.
u Have defective cords replaced immediately.
u Do not expose the charger to water.
u Do not open the charger.
u Do not probe the charger.
$
+
The charger is intended for indoor use only.
Read the instruction manual before use.
Electrical safety
#
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on
the rating plate. Never attempt to replace the
charger unit with a regular mains plug.
u
If the supply cord is damaged, it must be replaced
by the manufacturer or an authorised Stanley FatMax Service
Centre in order to avoid a hazard
Features
This tool includes some or all of the following features.
1. On/Off switch
2. Forward/reverse selecter
3. Drilling mode selector
4. Depth stop
5. Tool holder
6. Side handle
7.Battery (Not supplied)
Assembly
Use
Warning! Let the tool work at its own pace. Do not overload.
Charging the battery ((Two batteries provided with
the FMCD900M2S & FMCD900M2T units, no
batteries provided with the FMCD900B unit) (fig. A)
The battery needs to be charged before first use and
whenever it fails to produce sufficient power on jobs that were
easily done before. The battery may become warm while
charging; this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
6
The battery should be left in the charger and the charger will
begin to charge automatically when the cell temperature
warms up or cools down.
u To charge the battery, insert the Battery (7) into the
charger (9). The battery will only fit into the charger one
way.
u Plug the charger (9) into a suitable power source and
switch on.
u Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Fitting and removing the battery (Two batteries
provided with the FMCD900M2S & FMCD900M2T
units, no batteries provided with the FMCD900B
unit) (fig. B)
u To fit the battery, line it up with the receptacle on the tool
(11). Slide the battery into the receptacle and push until
the battery snaps into place.
u To remove the battery, push the release button (12) and
remove the battery from the receptacle.
Fitting the side handle (fig. C)
Turn the grip counterclockwise until you can slide the side
handle (6) onto the front of the tool as shown.
u Rotate the side handle into the desired position.
u Tighten the side handle by turning the grip clockwise.
u
Fitting and setting the depth stop (fig. C)
Depress the button (8).
Insert the depth stop (4) into the mounting hole as shown.
u Set the depth stop (4) to the desired position. The
maximum drilling depth is equal to the distance between
the tip of the drill bit and the front end of the depth stop.
u Release the button (8).
u
u
Fitting an accessory (fig. D - E)
Clean and grease the shank (13) of the accessory.
Pull back the sleeve (14) and insert the shank into the tool
holder (5).
u Push the accessory down and turn it slightly until it fits into
the slots.
u Pull on the accessory to check if it is properly locked. The
hammering function requires the accessory to be able to
move axially several centimetres when locked in the tool
holder.
u To remove the accessory, pull back the sleeve (14) and
pull out the accessory.
u
u
Keyed chuck (fig. F) (Not provided)
u Open the chuck by turning the sleeve (15) anti-clockwise.
u Insert the bit shaft (17) into the chuck.
u Insert the chuck key (18) into each hole (16) in the side of
the chuck and turn clockwise until tight.
ENGLISH
(Original instructions)
Warning! Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
Warning! Do not apply chisels when the tool is in the drilling
mode.
Switching on and off (fig. G)
u
u
To switch the tool on, press the on/off switch (1).
To switch the tool off, release the on/off switch.
Forward/reverse action (fig. H)
u
Move the selecter (2) to indicate the direction you require.
Selecting the operating mode (fig. I)
The tool can be used in three operating modes.
u To operate the operating mode selector (3), push the
unlock button (21) and rotate the selector towards the
required position, as indicated by the symbols.
Drilling
u For drilling in steel, wood and plastics, and for
screwdriving set the operating mode selector (3) to the
position (22).
Hammer drilling
u For hammer drilling in masonry and concrete, set the
operating mode selector (3) to the
position (19).
When hammering, the tool should not bounce and run
smoothly. If necessary, increase the speed.
Hammering
u For hammering with spindle lock, and for light chiselling
and chipping, set the operating mode selector (3) to the
position (20).
u When changing from hammer drilling to chiselling, turn the
chisel to the desired position. If resistance is felt during
mode change, slightly turn the chisel to engage the
spindle lock.
Accessories
The performance of your tool depends on the accessory used.
Stanley Fat Max accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your Stanley Fat Max corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
u Switch off and unplug the appliance/tool.
u Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u Regularly open the chuck and tap it to remove any dust
from the interior (when fitted).
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
u Safely dispose of the old plug.
u Connect the brown lead to the live terminal in the new
plug.
u Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
Protecting the environment
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled, reducing demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical data
FMCD900M1S
FMCD900M2S/
FMCD900M2T
FMCD900B
Input voltage
VDC
18
18
18
No-load speed
min-1
0 - 2200
0 - 2200
0 - 2200
Impact rate
min-1
0 - 5775
0 - 5775
0 - 5775
2.80
2.80
2.15
Weight
kg
Max. drilling capacity
Concrete
mm
20
20
20
Steel
mm
13
13
13
Wood
mm
30
30
30
FMC688L
Not
Supplied
Battery
FMC688L
Voltage
VDC
18
18
Capacity
Ah
4.0
4.0
type
Charger
Li-Ion
Li-Ion
906086**
typ. 1
906086**
typ. 1
Input Voltage
VAC
230
230
Output Voltage
VDC
18
18
Not
Supplied
7
FMCD900M1S
Current
Approx. Charge
time
FMCD900M2S/
FMCD900M2T
A
2.0
2.0
min
120
120
FMCD900B
Level of sound pressure according to EN 60745:
These products also comply with Directive 2006/42/EC,
2014/30/EU and 2011/65/EU. For more information, please
contact Stanley FatMax at the following address or refer to the
back of the manual.
The undersigned is responsible for compilation of the technical file and makes this declaration on behalf of
Stanley FatMax.
Sound pressure (LpA) 88.1 dB(A), uncertainty (K) 3 dB(A)
Sound power (LWA) 99.1 dB(A), uncertainty (K) 3 dB(A)
Vibration total values (triax vector sum) according to EN 60745:
Hammer drilling into concrete (ah, HD) 13.3 m/s2, uncertainty (K) 1.5 m/s2
Chiselling (ah, Cheq) 10.7 m/s2, uncertainty (K) 1.5 m/s2
EC declaration of conformity
R. Laverick
Director of Engineering
Stanley Europe, Egide Walschaertsstraat14-18,
2800 Mechelen, Belgium
08/08/2017
MACHINERY DIRECTIVE
FMCD900 SDS Rotary hammer
Stanley Europe declares that these products described under
"technical data" are in compliance with:
EN60745-1:2009+A11:2010, EN60745-2-6:2010.
United Kingdom
Stanley Fat Max
210 Bath Road
Slough, Berkshire SL1 3YD
N541398 REV-2
Guarantee
Stanley Fat Max is confident of the quality of its products and
offers consumers a 12 month guarantee from the date
of purchase. This guarantee is in addition to and in no way
prejudices your statutory rights. The guarantee is valid within
the territories of the Member States of the European Union
and the European Free Trade Area.
To claim on the guarantee, the claim must be in accordance
with Stanley Fat Max Terms and Conditions and you will need
to submit proof of purchase to the seller or an authorised
repair agent.
Terms and conditions of the Stanley Fat Max 1 year guarantee
and the location of your nearest authorised repair agent can
be obtained on the Internet at www.2helpU.com, or by
contacting your local Stanley Fat Max office at the address
indicated in this manual.
Tel. 01753 511234
Fax 01753 572112
www.stanleytools.co.uk
06/2018
Download PDF

advertising