BEMW471ES | Black&Decker BEMW471ES MOWER instruction manual

5
2 5 1
2
3
3
4
6
7
8
9
15
10
11
14
13
12
11
www.blackanddecker.co.uk
BEMW461ES
BEMW471ES
BEMW481ES
15
15
14a
14a
14c
14b
14d
A
14b
B
14c
14b
C
14b
14a 14c
D
14a
9
14c
14d
E
2
F
6
8
7
16
7
9
H
G
10
14
14g
2
J
14f
I
5
13
5
J1
5
K
3
ENGLISH
(Original instructions)
12
1
3
L
M
2
8
3
4
1
N
P
4
O1
O2
Q
(Original instructions)
17
ENGLISH
18
9a
19
R
S
17
18
18
20
21
19
T
U
18
18
22
23
V
W
5
ENGLISH
(Original instructions)
Intended use
Your BLACK+DECKER BEMW461ES, BEMW471ES,
BEMW481ES lawn mowers have been designed for mowing
grass. These appliances are intended for consumer use only.
Safety instructions
Warning! When using mains-powered
appliances, basic safety precautions,
including the following, should always be
followed to reduce the risk of fire, electric
shock and personal injury.
uRead all of this manual carefully before
using the appliance.
uThe intended use is described in this
manual. The use of any accessory
or attachment or the performance
of any operation with this appliance
other than those recommended in this
instruction manual may present a risk
of personal injury.
uRetain this manual for future
reference.
Training
the instructions carefully. Be
familiar with the controls and the
proper use of the appliance.
u Never allow children or people
unfamiliar with these instructions to
use the machine. Local regulations
can restrict the age of the operator.
u Never operate the machine while
people, especially children, or pets are
nearby.
u Keep in mind that the operator or user
is responsible for accidents or hazards
occurring to other people or their
property.
u
6
Read
Preparation
operating the machine always
wear substantial footwear and long
trousers.
Do not operate the machine when
barefoot or wearing open sandals.
Avoid wearing clothing that is loose
fitting or that has hanging cords or ties.
uThoroughly inspect the area where the
machine is to be used and remove all
objects which can be thrown by the
machine.
uBefore using, always visually inspect
to see that the blade, blade bolt and
the blade assembly are not worn or
damaged. Replace worn or damaged
components in sets to preserve
balance. Replace damaged or
unreadable
labels.
uBefore use check the supply and
extension cord for signs of damage or
aging. If the cord becomes damaged
during use, disconnect the cord
from the supply immediately. DO
NOT TOUCH THE CORD BEFORE
DISCONNECTING THE SUPPLY.
Do not use the machine if the cord is
damaged or worn.
uWear safety glasses or goggles when
operating this tool.
Use a face or dust mask whenever
the operations take place in dusty
surroundings. Hearing protection
should be worn whenever the sound
level seems uncomfortable.
uGuard against electric shock.
u
While
(Original instructions)
Prevent body contact with earthed or
grounded surfaces (e.g. metal railings,
lampposts, etc.).
Operation
u
Never operate the appliance with
defective guards or shields, or without
safety devices, for example deflectors
and/or grass catchers, in place.
uOnly use the appliance in daylight or
good artificial light.
uDo not expose the appliance to rain.
Do not use the appliance in damp or
wet conditions. Preferably do not use
the appliance in wet grass.
uBe sure of your footing, particularly on
slopes. Be aware that freshly cut grass
is damp and slippery. Do not work on
steep slopes.
uWork across the face of slopes, never
up and down. Take extreme caution
when changing direction on slopes.
uDo not mow excessively steep slopes.
uWalk, never run when using the
appliance. Do not pull the appliance
towards you or walk backwards when
using the appliance.
uSwitch on the appliance according to
instructions and with your feet well
away from the blade.
uDo not start the machine when
standing in front of the discharge
opening.
uDo not tilt appliance when switching it
on, except if the appliance has to be
tilted for starting.
ENGLISH
In that case, do not tilt the appliance
more than absolutely necessary and
lift only the part that is away from the
operator. Always ensure that both
hands are in the operating position
before returning the appliance to the
ground.
uSwitch off the appliance and wait for
the blade assembly to stop running
if the appliance has to be tilted
for transportation when crossing
surfaces other than grass, and when
transporting the appliance to and from
the area to be mowed.
uDo not lift or carry the appliance until
the blade has come to a complete
standstill.
uKeep your hands and feet well away
from the blade.
uDo not put your hands or feet near or
under rotating parts.
uKeep away from discharge openings at
all times.
uSwitch off, remove the plug from
the socket and ensure that moving
parts have stopped rotating before
leaving the appliance unattended
and before changing, cleaning or
inspecting any parts of the appliance
or clearing a blockage. After striking
a foreign object. Inspect the machine
for damage and make repairs before
restarting and operating the machine;
uIf the appliance starts to vibrate
abnormally or if you hit a foreign
object, switch the appliance off and
remove the plug from the socket.
7
ENGLISH
(Original instructions)
Check for any damage to the
appliance, replace or repair any
damaged parts, check for and tighten
any loose parts.
uTake care to keep the mains cable
away from the blade. Always be aware
of the position of the cable.
uThe motor will continue to run for a few
seconds after switching the appliance
off. Never attempt to force the blade to
come to a standstill.
Maintenance and storage
use, check the appliance for
damaged or defective parts.
Check for misalignment and seizure
of moving parts, breakage of parts,
damage to guards and switches
and any other conditions that may
affect its operation. Ensure that the
appliance will operate properly and
perform its intended function. Never
use the appliance when any guard or
enclosure is damaged or not in place.
Do not use the appliance if any part is
damaged or defective. Do not use the
appliance if the switch does not turn it
on and off.
Have any damaged or defective parts
repaired or replaced by an authorised
repair agent.
u Check the cable frequently for
damage. If the cable is damaged, it
must be replaced by an authorised
repair agent in order to prevent a
hazard. Inspect extension cables
periodically. Replace a damaged
extension cable immediately.
u
8
Before
all nuts, bolts and screws on
the appliance tight to ensure a safe
working condition.
u Check the grass collector for wear or
damage and replace it if necessary.
Never use the appliance without the
grass collector.
u Be careful during adjustment of the
machine to prevent entrapment of the
fingers between moving blades and
fixed parts of the machine.
u When servicing the blades be aware
that, even though the power source is
switched off, the blades can still be
moved.
u When not in use, the appliance should
be stored in a dry place. Children
should not have access to stored
appliances.
u Always allow the machine to cool
down before storing.
u Ensure that only replacement cutting
means of the right type are used.
u Use only BLACK+DECKER
recommended spare parts and
accessories.
u
Keep
Additional safety instructions for
Lawnmowers
u
Always use an approved extension
cable suitable for the power input of
this tool (see technical data). The
extensioncable must be suitable for
outdoor use and marked accordingly.
Up to 30 m of 1.5 mm2 HO5VV-F
extension cable can be used without
loss of product performance.
(Original instructions)
Before use, inspect the extension
cable for signs of damage, wear and
ageing. Replace the extension cable
if damaged or defective. When using
a cable reel, always unwind the cable
completely.
u Do not transport the machine while the
power source is running
u Firmly grip handle with both hands
when operating the lawn mower.
u If at any time it is felt necessary to tilt
the lawn mower, make sure that both
hands remain in the operating position
while the lawn mower is tilted. Keep
both hands in the operating position
until the lawn mower is returned to rest
correctly on the ground.
u Never wear radio or music
headphones while operating the lawn
mower.
u Never attempt to make a wheel height
adjustment while the motor is running
or while the safety key is in the switch
housing.
u If the lawn mower stalls, turn mower
off, wait for blade to stop, before
attempting to unclog the chute or
remove anything from under the deck.
u Keep hands and feet away from
cutting area.
u Keep blades sharp.
Always use protective gloves when
handling the lawn mower blade.
u If you are using the grass collector,
check it frequently for wear and
deterioration. If excessively worn,
replace with a new grass collector for
your safety.
ENGLISH
extreme caution when reversing
or pulling the lawn mower towards you.
u Do not put hands or feet near or under
the lawn mower.
Keep clear of the discharger opening
at all times.
u Clear the area where the lawn mower
is to be used of objects such as rocks,
sticks, wire, toys, bones etc., which
could be thrown by the blade.
Objects struck by the blade can cause
severe injury to persons. Stay behind
the handle when the motor is running.
u Do not operate the lawn mower
barefooted or while wearing sandals.
Always wear substantial footwear.
u Do not pull lawn mower backward
unless absolutely necessary. Always
look down and behind before and
while moving backward.
u Never direct discharged material
toward anyone. Avoid discharging
material against a wall or obstruction.
Material may ricochet back toward the
operator. Release the start handle to
turn the lawn mower off and stop the
blade when crossing gravel surfaces.
u Do not operate the lawn mower
without the entire grass collector,
discharge guard, rear guard, or other
safety protective devices in place and
working. Periodically check all guards
and safety protective devices to
ensure they are in good working order
and will operate properly and perform
their intended function.
u
Use
9
ENGLISH
(Original instructions)
Replace a damaged guard or other
safety device before further use.
u Never leave a running lawn mower
unattended.
u Always release the bail bar to stop the
motor and wait until the blade comes
to a complete stop before cleaning the
lawn mower, removing the grass bag,
unclogging the discharge guard, when
leaving the lawn mower, or before
making any adjustments, repairs or
inspections.
u Operate lawn mower only in daylight
or good artificial light when objects in
the path of the blade are clearly visible
from the operating area of the lawn
mower.
u Do not operate the lawn mower while
under the influence of alcohol or drugs,
or when your are tired or ill. Always
stay alert, watch what you are doing,
and use common sense.
u Avoid dangerous environments.
Never operate the lawn mower in
damp or wet grass, never use lawn
mower in the rain. Always be sure of
your footing, walk, never run.
u If the lawn mower should start to
vibrate abnormally, release the on/off
switch, wait for the blade to stop and
then check for the cause immediately.
Vibration is generally a warning of
trouble, see the troubleshooting guide
for advise in the case of abnormal
vibration.
u Always wear proper eye and
respiratory protection when operating
the lawn mower.
10
use of any accessory or
attachment not recommended for
use with this lawn mower could be
hazardous. Only use accessories
approved by BLACK+DECKER.
u Never overreach while operating the
lawn mower. Always be sure to keep
proper footing and balance at all times
while operating the lawn mower.
u Mow across the face of slopes, never
up and down. Exercise extreme
caution when changing direction on
slopes.
u Watch for holes, ruts, bumps, rocks or
other hidden objects. Uneven terrain
could cause a slip and fall accident.
Tall grass can hide obstacles.
u Do not mow on wet grass or
excessively steep slopes. Poor footing
could cause a slip and fall accident.
u Do not mow near drop-offs, ditches, or
embankments.
You could lose your footing or balance.
u Always allow the mower to cool down
before storing.
Pull the plug from the socket and pull
the battery pack from the machine. Make
sure that all moving parts have come to a
complete stop:
u Whenever you leave the machine;
u Before clearing a blockage;
u Before checking, cleaning or working
on the appliance.
u
The
(Original instructions)
Vibration
The declared vibration emission values
stated in the technical data and the
declaration of conformity have been
measured in accordance with a standard
test method provided by EN50636 and
may be used for comparing one tool with
another. The declared vibration emission
value may also be used in a preliminary
assessment of exposure.
Warning! The vibration emission value
during actual use of the power tool can
differ from the declared value depending
on the ways in which the tool is used.
The vibration level may increase above
the level stated.
When assessing vibration exposure to
determine safety measures required by
2002/44/EC to protect persons regularly
using power tools in employment, an
estimation of vibration exposure should
consider, the actual conditions of use and
the way the tool is used, including taking
account of all parts of the operating
cycle such as the times when the tool is
switched off and when it is running idle in
addition to the trigger time.
Do not operate the tool if the vibration
registers as abnormal.
Safety of others
u
This
appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge.
ENGLISH
Unless they have been given
supervision or instruction concerning
use of the appliance by a person
responsible for their safety.
u Children must be supervised to
ensure that they do not play with the
appliance.
u After striking a foreign object. Inspect
the appliance for damage and make
repairs as necessary.
Residual risks
Additional residual risks may arise when
using the tool which may not be included
in the enclosed safety warnings. These
risks can arise from misuse, prolonged
use etc. Even with the application of
the relevant safety regulations and the
implementation of safety devices, certain
residual risks can not be avoided. These
include:
u Injuries caused by touching any
moving parts.
u Injuries caused by touching any hot
parts.
u Injuries caused when changing any
parts or accessories.
u Injuries caused by prolonged use
of the appliance. When using any
appliance for prolonged periods
ensure you take regular breaks.
u Impairment of hearing.
u Health hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
11
ENGLISH
(Original instructions)
operating the mower in a damp
location is unavoidable, use a residual
current device (RCD) with a tripping
current of not more than 30 mA.
Use of an RCD reduces the risk of
electric shock.
u Never pick up or carry an appliance
while the motor is running.
u
If
Warning symbols
The following warning symbols are found
on the appliance along with the date
code:
Warning! Read the manual prior
to operation.
Do not expose the appliance to
rain or high humidity.
Always remove the plug from
the socket before inspecting
a damaged cable. Be careful
not to use your appliance if the
cable is damaged.
Beware of sharp blades.
Beware of flying objects. Keep
bystanders away from the
cutting area.
Keep the cable away from the
cutting blades.
The blades will continue to
rotate after the machine is
switched off.
12
96
Directive 2000/14/EC
guaranteed sound power
Electrical safety
Warning! This tool is double
insulated; therefore no earth
wire is required. Always
check that the power supply
corresponds to the voltage on
the rating plate.
u If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
u Electric safety can be further improved
by using a high sensitivity 30 mA
Residual Current Device (RCD).
Features
This appliance includes some or all of the following features.
1. Power button
2. Comfort grip handles
3. On/off switches
4. EasySteer pivot control
5. EasySteer pivot control buttons
6. Upper handle
7. Handle knobs
8. Cable management system (BEMW471ES, BEMW481ES
units only)
9. Lower handle
10. Back flap
11. Carrying handles
12. Height adjustment gauge
13. Height adjustment lever
14. Grass box
14. Grass box handle
Assembly
Warning! Before assembly, make sure that the appliance is
switched off and unplugged.
(Original instructions)
Assembling the grass collection box (fig. A, B, C, D
and E)
The grass box requires assembly before use and comes in 5
pieces.
u Clip the handle (15) into the lid (14a) of the grass box
(fig. B). The handle will only fit one way round.
u Clip the 2 sides (14b) and (14c) of the grass collection box
together. Make sure that all clips and guides are aligned
(fig. C).
u Align the lid (14a) onto the assembled grass collection
box. Ensure that the 10 guides are aligned (fig. D)
u Align the assembled sides onto the bottom (14d) of the
grass collection box. Ensure that the 4 guides are
aligned (fig. E)
u Push the 2 parts together. Apply even force around all
edges of the grass collection box securing the clips
into position uniformly. Check that each clip is fastened
together securely.
Adjusting the height of cut (fig. K)
The height of cut is adjusted by the central height adjust
mechanism, there are 6 positions to choose from.
u Pull the height adjustment lever (13) away from the body
of the unit.
u Move the lever towards the rear of the appliance to
lower the height of cut.
u Move the lever towards the front of the appliance to
raise the height of cut.
u Push the height adjustment lever into one of the 6
height locations.
NOTE: The height of cut can be viewed on the height of cut
gauge (12) on the side of the unit.
Switching on and off (fig. M)
Switching on
u
u
Fitting the lower handle (fig. F)
Insert the ends of the lower handles (9) into the
corresponding holes in the mower.
u Press the handle down as far as it will go.
u Secure the handle using the screws.
u
Assembling the upper handle (fig. G)
Fit the upper handle part to the lower handle using the
handle knobs (7) , washers and screws as shown.
u
Securing the motor cable (fig. H)
The motor cable has to be fixed using the cable restraint.
Snap a restraint clip (16) around the cable and lower
handle about 150mm below the handle knob (7).
u
u
Fitting the grass collection box (fig. I)
u
Lift the flap (10) and place the grass collection box (14)
ensuring the recesses (14f) fit over the lugs (14g).
Proper Hand Position (Fig. J)
Warning! To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
Warning!: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on each of the
comfort grip handles (2).
(Fig. J1)
EasySteer Innovation - The innovative handle design easily
moves from left to right at the push of a button, giving you
precision control and manouvrability around your garden.
ENGLISH
Push the power button (1).
Pull the left or right ON/OFF switch (3) towards the handle.
Switching off
u Release ON/OFF switches (3).
Warning! Never attempt to lock a switch in the on position.
Mowing (fig. N, O1 & O2)
We recommend to use your mower as outlined in this section
in order to achieve optimum results and to reduce the risk of
cutting the mains cable.
u Loop the extension cord through the cable
management system (5) (BEMW471ES, BEMW481ES
units only) as shown (Fig. N). Ensure you
leave approximately 100 of cord between the power
switch (1) and the cable management system.
u Ensure that the cable management system
(BEMW471ES, BEMW481ES GB units only) can slide
freely from one side to the other.
u Place the bulk of the mains cable on the lawn, close to the
starting point (position 1 in fig. O1).
u Switch the appliance on as described above.
u Proceed as shown in fig. O1
u Move from position 1 to position 2.
u Turn right and proceed towards position 3. The cable
management system will slide from one side to the other,
ensuring the extension cord is kept away from the cutting
blade.
u Turn left and move towards position 4.
u Repeat the above procedure as required.
Warning! Do not work towards the cable as shown in fig. O2.
Up to edge cutting (fig. P, Q)
Up to edge cutting allows you to cut grass right up to the edge
of a wall or fence (fig P).
Up to edge cutting allows you to accurately cut grass right up
to the edge of your lawn (fig Q).
13
ENGLISH
(Original instructions)
With the lawnmower parallel with the edge of your lawn,
push the lawnmower along the edge of the lawn. Ensure
that the edge of the mower is slightly over the edge of
your lawn (fig.Q).
u
Cable tidy (fig. R)
u
Cable tidy, stores cable when not in use. Only available on
BEMW471ES & BEMW481ES GB units.
Removing Blade (Fig. S, T)
Note: BEMW461ES / BEMW471ES & BEMW481ES all use
new winged blades which improves collection vs previous
range of mowers. Blade accessories Cat # 34cm A6320
38cm A6321 42cm A6322.
Warning! Ensure the blade has completely stopped and
disconnect the mower from the power source.
u Cut a piece of 2x4 wood (17) 305mm to keep blade from
turning while removing flange nut.
u Turn the appliance onto its side. Wear gloves and proper
eye protection. Be careful of sharp edges of blade.
u Position piece of wood (17) to keep blade from turning
as shown in Fig. S.
u Use a 14mm wrench (19) to loosen and remove the
blade bolt by turning counterclockwise.
u Pull off blade (18), blade insulator (20), as shown in
Fig. T. Examine all pieces for damage and replace if
necessary.
Installing Blade (Fig. U)
Place blade insulator (20) then the blade (18) onto bolt
shaft with the lettering on the blade facing out, and place
the blade bolt (21) onto the bolt shaft.
u Tighten the blade bolt as firmly as possible by hand.
u Position piece of wood (17) to keep blade from turning
as shown in Fig. U.
u Use a 14mm wrench to securely tighten the blade
bolt by turning the wrench clockwise.
u
Blade sharpening
Keep blade sharp for best mower performance. A dull blade
does not cut grass cleanly. Use proper eye protection while
removing, sharpening, and installing blade. Sharpening the
blade twice during a mowing season is usually sufficient under
normal circumstances.
Sand causes the blade to dull quickly. If your lawn has sandy
soil, more frequent sharpening may be required.
Note: Replace bent or damaged blade immediately.
When sharpening the blade:
u Make sure blade remains balanced.
u Sharpen blade at the original cutting angle.
u Sharpen cutting edges on both ends of blade, removing
equal amounts of material from both ends.
14
To sharpen blade in a vice (fig. V)
Be sure the blade has stopped and the mower is
unplugged before removing the blade.
u Remove blade from mower. See instructions for removing
and installing blade.
u Secure blade (18) in a vice (22).
u Wear proper eye protection and gloves and be careful not
to cut yourself.
Carefully file the cutting edges of the blade with a fine
tooth file (23) or sharpening stone, maintaining the angle
of the original cutting edge. Check balance of blade. See
instructions for blade balancing.
u Replace blade on mower and tighten securely.
u
Blade balancing (fig. W)
Check balance of the blade (18) by placing centre hole in
the blade over a nail or round shank screwdriver, clamped
horizontally in a vice. If either end of the blade rotates
downward, file along the sharp edge of that dropping end.
Blade is properly balanced when neither end drops.
Lubrication
No lubrication is necessary. Do not oil the wheels. They have
plastic bearing surfaces which require no lubrication.
Cleaning
Turn the mower off and let the blade come to a stop. Use only
mild soap and a damp cloth to clean the mower. Clean out any
clippings which may have accumulated on the underside of
the deck. After several uses, check all exposed fasteners for
tightness.
Preventing corrosion
Fertilizers and other garden chemicals contain agents which
greatly accelerate the corrosion of metals.
If you mow in areas where fertilizers or chemicals have been
used, the mower should be cleaned immediately afterward as
follows:
Turn the mower off and unplug mower. Wipe all exposed parts
with a damp cloth.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool/appliance care and regular
cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
u Switch off and unplug the appliance/tool.
u Or run the battery down completely if it is integral and then
switch off.
u Unplug the charger before cleaning it.
(Original instructions)
u
u
u
Your charger does not require any maintenance apart from
regular cleaning.
Regularly clean the ventilation slots in your tool/appliance
and charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Regularly use a blunt scraper to remove grass and dirt
from the underneath of the guard.
Troubleshooting
If your appliance seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local BLACK+DECKER repair agent.
Warning! Before proceeding, release the bail bar to turn
mower off and wait for the blade to stop.
Problem
Mower will
not start.
Possible cause
Cord is not
plugged in.
Circuit fuse is
blown.
Cord or switch
is damaged.
Possible solution
Plug mower into a working outlet.
Replace circuit fuse. (If
the product repeatedly
causes the circuit fuse
to blow, discontinue use
immediately and have
itserviced by an authorised BLACK+DECKER
service center.
Have cord or switch
replaced at an authorised BLACK+DECKER
service center.
Grass too long.
Increase the height of
cut and move machine
to shorter grass to start.
Machine func- Thermal cut out Allow motor to cool and
tions intermit- activated.
increase height of cut.
tently.
Machine
Height of cut
Increase height of cut.
leaves ragged too low.
finish or mo- Cutting blade
Replace the blade.
tor labours.
blunt.
Underside
Check underneath the
of machine
machine and clear out
clogged.
as necessary (always
wear heavy duty gloves)
Blade fitted
Refit blade correctly.
upside down.
ENGLISH
Products and batteries contain materials that can be
recovered or recycled, reducing demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical data
BEMW461ES
BEMW471ES
VAC
230
230
230
W
1400
1600
1800
min-1
3500
3500
3500
mm
20 - 70
20 - 70
20 - 70
Blade length
cm
34
38
42
Weight
Kg
15.17
15.94
17.17
Voltage
Power inpurt
No-Load
speed
Height
adjustment
BEMW481ES
Hand/arm weighted vibration value:
= 2.5m/s2 , uncertainty (K) = 1.5m/s2.
Sound pressure level at the operator's ear:
LPA: 82dB(A); K= 2.1dB(A)
Sound power level LWA: 95dB(A); K= 1.3dB(A)
EC declaration of conformity
%
MACHINERY DIRECTIVE
OUTDOOR NOISE DIRECTIVE
BEMW461ES, BEMW471ES, BEMW481ES lawn mower
Black & Decker declares that these products described under
"technical data" are in compliance with:
2006/42/EC, EN 60335-1:2012 + A11:2014,
EN 60335-2-77:2010
2000/14/EC, Lawn Mower, L < 50cm, Annex VI,
DEKRA Certification B.V. Meander 1051 / P.O. Box 5185
6825 MJ ARNHEM / 6802 ED ARNHEM Netherlands.
Level of accoustic power according to 2000/14/EC (Article 12,
Annex III, L< 50cm):
measured sound power level LWA: 95dB(A); K= 1.3dB(A).
guaranteed sound power level LWA: 96dB(A).
These products also comply with directive 2014/30/EU,
2011/65/EU. For more information, please contact Black &
Decker at the following address or refer to the back of the
manual.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
15
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of Black & Decker.
R. Laverick
Director of Engineering
Black & Decker Europe, 210 Bath Road, Slough,
Berkshire, SL1 3YD
United Kingdom
31/10/2017
Guarantee
Black & Decker is confident of the quality of its products
and offers consumers a 24 month guarantee from the date
of purchase. This guarantee is in addition to and in no way
prejudices your statutory rights. The guarantee is valid within
the territories of the Member States of the European Union
and the European Free Trade Area.
To claim on the guarantee, the claim must be in accordance
with Black & Decker Terms and Conditions and you will need
to submit proof of purchase to the seller or an authorised
repair agent. Terms and conditions of the Black & Decker 2
year guarantee and the location of your nearest authorised
repair agent can be obtained on the Internet at www.2helpU.
com, or by contacting your local Black & Decker office at the
address indicated in this manual.
Please visit our website www.blackanddecker.co.uk to register
your new Black & Decker product and receive updates on new
products and special offers.
Australia
Black & Decker (Australia) Pty. Ltd.
20 Fletcher Road, Mooroolbark,
Victoria, 3138
Tel. Fax
03-8720 5100
03-9727 5940
New Zealand
Black & Decker
5 Te Apunga Place
Mt Wellington
Aukland 1060
Tel. Fax
+64 9 259 1133
+64 9 259 1122
United Kingdom &
Republic Of Ireland
www.blackanddecker.co.uk emeaservice@sbdinc.com
Black & Decker
210 Bath Road
Slough, Berkshire SL1 3YD
Tel. Fax
01753 511234
01753 512365
N533563 REV-01
11/2017
Download PDF

advertising