KR714S32 | Black&Decker KR714S32 HAMMER DRILL instruction manual

www.blackanddecker.com.au
www.blackanddecker.co.nz
CD714RE
CD714CRE
CD714CRES
KR604CRES
KR654CRES
KR714CRES
English
2
(Original instructions)
5
7
A
B
10
11
14
12
15
12
C
D
11
3
E
F
3
6
G
4
7
ENGLISH
Intended use
f.
If operating a power tool in a damp location is
unavoidable, use a Residual Current Device (RCD)
protected supply. Use of an RCD reduces the risk
of electric shock.
Your BLACK+DECKER CD714RE, CD714CRE, CD714CRES,
KR604CRES, KR654CRES, KR714CRES drill has been designed
for drilling in wood, metal and plastics and masonry as well as for
screwdriving purposes. This tool is intended for consumer use 3. Personal safety
only.
a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
Safety instructions
use a power tool while you are tired or under the
General power tool safety warnings
influence of drugs, alcohol or medication. A moment
Warning! Read all safety warnings and all
of inattention while operating power tools may result in
! instructions. Failure to follow all instructions may
serious personal injury.
result in electric shock, fire and/or serious injury.
b. Use personal protective equipment. Always wear
Save all warnings and instructions for future reference.
eye protection. Protective equipment such as dust
The term “power tool” in all of the warnings listed below
mask, non-skid safety shoes, hard hat, or hearing
refers to your mains operated (corded) power tool or
protection used for appropriate conditions will reduce
battery operated (cordless) power tool.
personal injuries.
c. Prevent unintentional starting. Ensure the switch
1. Work area safety
is in the off-position before connecting to power
a. Keep work area clean and well lit. Cluttered and
source and/or battery pack, picking up or carrying
dark areas invite accidents.
the tool. Carrying power tools with your finger on the
b. Do not operate power tools in explosive
switch or energising power tools that have the switch
atmospheres, such as in the presence of flammable
on invites accidents.
liquids, gases or dust. Power tools create sparks
d. Remove any adjusting key or wrench before turning
which may ignite the dust or fumes.
the power tool on. A wrench or a key left attached to
c. Keep children and bystanders away while operating
a rotating part of the power tool may result in personal
a power tool. Distractions can cause you to lose
injury.
control.
e. Do not overreach. Keep proper footing and balance
2. Electrical safety
at all times. This enables better control of the power
a. Power tool plugs must match the outlet. Never
tool in unexpected situations.
modify the plug in any way. Do not use any adapter
f. Dress properly. Do not wear loose clothing or
plugs with earthed (grounded) power tools.
jewellery. Keep your hair, clothing and gloves away
Unmodified plugs and matching outlets will reduce
from moving parts. Loose clothes, jewellery or long
risk of electric shock.
hair can be caught in moving parts.
b. Avoid body contact with earthed or grounded
g. If devices are provided for the connection of dust
surfaces such as pipes, radiators, ranges and
extraction and collection facilities, ensure these are
refrigerators. There is an increased risk of electric
connected and properly used. Use of these devices
shock if your body is earthed or grounded.
can reduce dust related hazards
c. Do not expose power tools to rain or wet conditions.
4. Power tool use and care
Water entering a power tool will increase the risk of
a. Do not force the power tool. Use the correct power
electric shock.
tool for your application. The correct power tool will
d. Do not abuse the cord. Never use the cord for
do the job better and safer at the rate for which it was
carrying, pulling or unplugging the power tool.
designed.
Keep cord away from heat, oil, sharp edges or
b. Do not use the power tool if the switch does not turn
moving parts. Damaged or entangled cords increase
it on and off. Any power tool that cannot be controlled
the risk of electric shock.
with the switch is dangerous and must be repaired.
e. When operating a power tool outdoors, use an
c. Disconnect the plug from the power source and/or
extension cord suitable for outdoor use. Use of
the battery pack from the power tool before making
a cord suitable for outdoor use reduces the risk of
any adjustments, changing accessories, or storing
electric shock.
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
5
ENGLISH
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is
maintained.
b. Power to the tool should always be supplied via
residual current device with a rated residual
current of 30mA or less.
Additional power tool safety warnings
!
Warning! Additional safety warnings for drills and
impact drills.
Wear ear protectors when impact drills. Exposure
to noise can cause hearing loss.
Use auxiliary handle(s) if supplied with the tool.
Loss of control can cause personal injury.
Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a “live” wire may
make exposed metal parts of the power tool “live”
and shock the operator.
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body leaves it unstable
and may lead to loss of control.
Before drilling into walls, floors or ceilings, check for the
location of wiring and pipes.
Avoid touching the tip of a drill bit just after drilling,
as it may be hot.






6

The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those
recommended in this instruction manual may present
a risk of personal injury and/or damage to property.
Safety of others
This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.

Children should be supervised to ensure that they do
not play with the appliance.

Vibration
The declared vibration emission values stated in the
technical data and the declaration of conformity have
been measured in accordance with a standard test method
provided by EN 60745 and may be used for comparing one
tool with another. The declared vibration emission value may
also be used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons
regularly using power tools in employment, an estimation
of vibration exposure should consider, the actual conditions
of use and the way the tool is used, including taking account
of all parts of the operating cycle such as the times when the
tool is switched off and when it is running idle in addition
to the trigger time.
Labels on tools
The following pictograms are shown on the tool along with
the date code:
Warning! To reduce the risk of injury, the user must
read the instruction manual.
Electrical safety

This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
If the supply cord is damaged, it must be replaced by
the manufacturer or an authorised BLACK+DECKER
Service Centre in order to avoid a hazard.
ENGLISH
Features
1.
2.
3.
4.
5.
6.
7.
Variable speed switch
Lock-on button
Forward/reverse button
Drilling mode selector
Chuck
Depth stop (Not all models)
Side handle (Not all models)
fig. B
8. Manual spindle lock button (single sleeve keyless
chuck only)




Tighten an Allen key into the chuck and strike it with
a hammer as shown.
Remove the Allen key.
Remove the chuck by turning it counter clockwise.
To refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Fitting the side handle and depth stop (fig. A & G)

Turn the grip counter clockwise until you can slide the
side handle (7) onto the front of the tool as shown.

Rotate the side handle into the desired position.

Insert the depth stop (6) into the mounting hole as
shown.

Set the drilling depth as described below.

Tighten the side handle by turning the grip clockwise.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These include:

Injuries caused by touching any rotating/moving parts.

Injuries caused when changing any parts, blades or
accessories.

Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods make sure you take
regular breaks.

Impairment of hearing.

Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF).
Fitting a drill bit
Use
Single sleeve keyless chuck (fig. B)

Open the chuck by pressing the manual spindle lock
button (8) and turning the sleeve (9) counter clockwise.

Insert the bit shaft (12) into the chuck.

Firmly tighten the chuck by pressing the manual spindle
lock button (8) and turning the sleeve clockwise until
it is tight.
Selecting the direction of rotation (fig. F)
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Two sleeve keyless chuck (fig. C)

Open the chuck by turning the front part (10) with one
hand while holding the rear part (11) with the other.

Insert the bit shaft (12) into the chuck and firmly
tighten the chuck.
Keyed chuck (fig. D)

Open the chuck by turning the sleeve (13) counter
clockwise.

Insert the bit shaft (12) into the chuck.

Insert the chuck key (14) into each hole (15) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (fig. E)

Open the chuck as far as possible.

Remove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, floors or ceilings, check
for the location of wiring and pipes.
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counter clockwise) rotation.

To select forward rotation, push the forward/reverse
button (3) to the left position.

To select reverse rotation, push the forward/reverse
button to the right.
Warning! Never change the direction of rotation while the
motor is running.
Selecting the drilling mode

For drilling in masonry, set the drilling mode selector (4)
to the position.

For drilling in other materials and for screwdriving,
set the drilling mode selector to the position.
Setting the drilling depth (fig. G)

Slacken the side handle (7) by turning the grip counter
clockwise.
7
ENGLISH
Set the depth stop (6) to the desired position. The
maximum drilling depth is equal tothe distance between
the tip of the drill bit and the front end of the depth stop.
Tighten the side handle by turning the grip clockwise.


Switching on and off

To switch the tool on, press the variable speed
switch (1). The tool speed depends on how far you
press the switch. As a general rule, use low speeds
for large diameter drill bits and high speeds for smaller
diameter drill bits.

For continuous operation, press the lock-on button (2)
and release the variable speed switch. This option is
available only at full speed in both forward and reverse
modes.

To switch the tool off, release the variable speed switch.
To switch the tool off when in continuous operation,
press the variable speed switch again and release it.
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your BLACK+DECKER
product needs replacement, or if it is of no further use to
you, do not dispose of it with household waste. Make this
product available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the
demand for raw materials.
Accessories
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
The performance of your tool depends on the accessory
used. BLACK+DECKER and Piranha accessories are
engineered to high quality standards and designed to
enhance the performance of your tool. By using these
accessories you will get the very best from your tool.
BLACK+DECKER provides a facility for the collection and
recycling of BLACK+DECKER products once they have
reached the end of their working life. To take advantage of
this service please return your product to any authorised
repair agent who will collect them on our behalf.
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
Warning! Before performing any maintenance, switch off
and unplug the tool.

Regularly clean the ventilation slots in your tool using
a soft brush or dry cloth.

Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.

Regularly open the chuck and tap it to remove any dust
from the interior (when fitted).
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:

Safely dispose of the old plug.

Connect the brown lead to the live terminal in the
new plug.

Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality
plugs. Recommended fuse: 5 A.
8
You can check the location of your nearest authorised
repair agent by contacting your local BLACK+DECKER
office at the address indicated in this manual.
Alternatively, a list of authorised BLACK+DECKER repair
agents and full details of our after-sales service and
contacts are available on the Internet at:
www.2helpU.com.
ENGLISH
Technical data
Input voltage
Power input
No load speed
Max drilling
capacity
Steel/concrete
Wood
Weight
Input voltage
Power input
No load speed
Max drilling
capacity
Steel/concrete
Wood
Weight
CD714
RE
TYPE 3
Vac 230
W 710
min-1 0-2800
mm 13
mm 25
kg 2.0
KR604
CRES
TYPE 3
Vac 230
W 600
min-1 0-2800
mm 13
mm 20
kg 2.0
CD714
CRE
TYPE 3
230
710
0-2800
CD714
CRES
TYPE 3
230
710
0-2800
13
25
2.0
13
25
2.0
KR654
CRES
TYPE 3
230
650
0-2800
KR714
CRES
TYPE 3
230
710
0-2800
13
20
2.0
13
25
2.0
Level of sound pressure according to EN 60745:
Sound pressure (LpA) 101 dB(A), uncertainty (K) 3 dB(A)
Sound power (LWA) 112 dB(A), uncertainty (K) 3 dB(A)
EC declaration of conformity
MACHINERY DIRECTIVE
CD714RE, CD714CRE, CD714CRES,KR604CRES,
KR654CRES, KR714CRES - Drill
Black & Decker declares that these products described
under "technical data" are in compliance with:
98/37/EC (until Dec. 28, 2009),
2006/42/EC, 2014/30/EU, 2011/65/EU, (from Dec. 29, 2009),
EN60745-1:2009+A11:2010 and EN60745-2-1:2010
For more information, please contact Black & Decker at the
following address or refer to the back of the manual.
The undersigned is responsible for compilation of the
technical file and makes this declaration on behalf of Black
& Decker.
R.Laverick
Engineering Director
Black & Decker Europe, 210 Bath Road, Slough, Berkshire,
SL1 3YD
United Kingdom
28/02/2017
Vibration total values (triax vector sum)
according to EN 60745:
Impact drilling into concrete (ah, ID)= 17.97 m/s²,
uncertainty (K) = 1.5 m/s²
Drilling into Metal (ah, D)= 3.37 m/s²,
uncertainty (K) = 1.5 m/s²
9
ENGLISH
Australia & New Zealand
Stanley
St
Black & Decker
www.blackanddecker.com.au
www.blackanddecker.co.nz
Tel.1800 338 002 (Aust) or Tel. 0800 339 258 (NZ)
10
N588877
03/2018
Download PDF

advertising