LG | ST600 | LG ST600 Owner’s Manual

ENGLISH
OWNER’S MANUAL
Smart TV Upgrader
Please read this manual carefully before operating
your set and retain it for future reference.
ST600
P/NO : SAC35193509
www.lg.com
Getting Started
Safety Information
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral
triangle is intended to alert the user
to the presence of un-insulated
dangerous voltage within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing the
product on a bed, sofa, rug or other similar surface.
This product shall not be placed in a
bulletin installation such as a bookcase or rack
unless proper ventilation is provided or the
manufacturer’s instruction has been adhered to.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
centre. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. When installing the product,
ensure that the plug is easily accessible.
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
1
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
3
4
Getting Started
yy The appliance is not intended for use by young
children or infirm persons without supervision.
1
yy Young Children should be supervised to ensure
that they do not play with appliance.
Getting Started
yy If the appliance is supplied from a cord
extension set or an electrical portable outlet
device, the cord extension set on electrical
portable outlet device must be positioned so
that it is not subject to splashing or ingress of
moisture.
Notes on Copyrights
Recording equipment should be used only for
lawful copying and you are advised to check
carefully what is lawful copying in the area in which
you are making a copy. Copying of copyright
material such as films or music is unlawful unless
permitted by a legal exception or consented to by
the rights owner.
Getting Started
5
1
Getting Started
6
Table of Contents
Table of Contents
4 Operating
27
27
27
1
Getting Started
3
8
8
8
10
10
10
10
11
11
Safety Information
Introduction
– About the “7” Symbol Display
– File requirement
– About DLNA
– Certain System Requirements
– LG Remote
– Compatibility Notes
Main Unit
Remote control
2 Connecting
12
12
13
14
14
15
16
16
17
18
18
21
21
Connecting the AC Adapter
HDMI Connecting to Your TV
– Resolution Setting
Connecting to an Amplifier
– Connecting to an Amplifier via HDMI
Output
– Connecting to an Amplifier via Digital
Audio Output
Connecting to your Home Network
– Wired network connection
– Wired Network Setup
– Wireless Network Connection
– Wireless Network Setup
USB device connection
– Playback content in the USB device
3 System Setting
22
22
22
23
24
25
25
Settings
– Adjust the Setup Settings
– [DISPLAY] Menu
– [LANGUAGE] Menu
– [AUDIO] Menu
– [NETWORK] Menu
– [OTHERS] Menu
28
29
31
31
32
32
32
32
32
33
33
33
34
34
34
35
35
35
35
35
36
36
37
37
37
38
38
39
39
40
40
41
41
42
42
43
General Playback
– Using [HOME] menu
– Playing a file media from a USB
device
– Playing a file media from a network
server
– Wi-Fi Direct™ Connection
– Basic operations for video and audio
content
– Basic operations for photo content
Advanced Playback
– Zoom in & out during slide show
– Repeat Playback
– Viewing content information
– Changing content list view
– Selecting a subtitle file
– Setting your photo as a wallpaper
– Options while viewing a photo
– Listening to music while slide show
On-Screen display
– Displaying content information onscreen
– Playing from selected time
– Listening to a different audio track
– Selecting a subtitle language
– Changing TV Aspect Ratio
– Changing subtitle code page
– Changing Picture Mode
Using the Premium
Using the LG Apps
– Signing in
– Managing my Apps
Using the Browser Home
– About the Browser Home menu
– Editing your favorite web pages
– Additional browser options
Playing content via Media Link
– Mide Link connection
– Using the Media Link
– Using Movie section
– Using Music section
– Using TV Program section
– Plug-in installation
Table of Contents
7
5 Troubleshooting
44
44
44
45
45
45
45
Troubleshooting
– General
– Picture
– Resetting
– Network
– Customer Support
– Open source software notice
1
2
6 Appendix
46
46
46
47
47
48
49
50
51
52
52
52
Network Software Update
– Network update notification
– Software Update
About Nero MediaHome 4 Essentials
– Installing Nero MediaHome 4
Essentials
– Sharing files and folders
Trademarks and Licenses
Audio Output Specifications
Specifications
Maintenance
– Handling the Unit
Important Information Relating to
Network Services
3
4
5
6
8
Getting Started
Introduction
1
About the “7” Symbol Display
Getting Started
“7” may appear on your TV display during operation and indicates that the function explained in this
owner’s manual is not available on that specific media.
File requirement
Video files
File
Location
File
Extension
Codec Format
Audio Format
Subtitle
“.avi”, “.divx”,
“.mpg”, “.mpeg”,
“.mkv”, “.mp4”,
“.asf”, “.wmv”,
“.m4v” (DRM
free)
DIVX3.xx, DIVX4.xx,
DIVX5.xx, DIVX6.xx
(standard playback
only), XVID, H.264/
MPEG-4 AVC, VC-1
SM (WMV3), MPEG1,
MPEG2
Dolby Digital,
DTS, MP3,
WMA, AAC,
Dolby Digital
Plus
SubRip (.srt / .txt), SAMI (.smi),
SubStation Alpha (.ssa/.txt),
MicroDVD (.sub/.txt), VobSub
(.sub), SubViewer 1.0 (.sub),
SubViewer 2.0 (.sub/.txt), TMUnit
(.txt), DVD Subtitle System (.txt)
“.avi”, “.divx”,
“.mpg”, “.mpeg”,
DLNA, PC
“.mkv”, “.mp4”,
“.asf”, “.wmv”
DIVX3.xx, DIVX4.xx,
DIVX5.xx, DIVX6.xx
(standard playback
only), XVID, H.264/
MPEG-4 AVC, VC-1
SM (WMV3), MPEG1,
MPEG2
Dolby Digital,
DTS, MP3,
WMA, AAC,
Dolby Digital
Plus
SubRip (.srt / .txt), SAMI (.smi),
SubStation Alpha (.ssa/.txt),
MicroDVD (.sub/.txt), SubViewer
1.0 (.sub), SubViewer 2.0 (.sub/.
txt), TMUnit (.txt), DVD Subtitle
System (.txt)
USB
Media
Link
“.mp4”, “.asf”,
“.wmv”
Audio files
File
Location
File
Extension
Sampling Frequency
Bitrate
USB,
DLNA, PC
“.mp3”, “.wma”,
“.m4a” (DRM
free)
within 32 - 48 kHz
(WMA), within 16 - 48
kHz (MP3)
within 20 - 320 kbps
(WMA), within 32 - 320
kbps (MP3)
Media Link
“.mp3”, “.wma”
Note
Some audio files are
not supported on
this unit.
Photo files
File
Location
USB,
DLNA, PC
File
Extension
“.jpg”, “.jpeg”,
“.png”,
Recommended
Size
Note
Less than 4,000 x 3,000 x 24 bit/pixel Progressive and lossless
Less than 3,000 x 3,000 x 32 bit/pixel compression photo image files
are not supported.
Getting Started
9
,,Note
yy The file name is limited to 180 characters.
yy Maximum files/Folder: Less than 2000 (total number of files and folders)
yy Depending on the size and number of the files, it may take several minutes to read the contents on
the media.
yy The file requirements on page 8 are not always compatible. There may have some restrictions by file
features and media server’s ability.
yy Playing a video subtitle files are only available on share folder of a PC or DLNA media server created
by supplied Nero MediaHome 4 Essentials software on this unit package.
yy The files from removable media such as USB drive etc. on your media server may not be shared
properly.
yy This unit cannot support the ID3 Tag embedded MP3 file.
yy The total playback time of audio file indicated on the screen may not correct for VBR files.
yy HD video files contained on the USB 1.0/1.1 may not played properly. USB 2.0 are recommended to
play back HD video files.
yy This unit supports H.264/MPEG-4 AVC profile Main, High at Level 4.1. For a file with higher level, the
warning message will appear on the screen.
yy This unit does not support files that are recorded with GMC or Qpel.
yy GMC – Global Motion Compensation
yy Qpel – Quarter pixel
Getting Started
yy File compatibility may differ depending on the server.
yy Because the compatibility on DLNA server are tested on the bundle DLNA server (Nero MediaHome
4 Essentials) environment, file requirements and playback functions may differ depending on media
servers.
1
10
1
Getting Started
Getting Started
About DLNA
LG Remote
This Unit is a DLNA Certified digital media unit
that can display and play movie, photo and music
content from your DLNA-compatible digital media
server (PC and Consumer Electronics).
You can control this unit with your iPhone or
Android phone via your home network. This unit
and your phone must be connected to your
wireless network device such as access point.
Visit “Apple iTunes” or “Google Apps Marketplace” for
detailed information of “LG Remote”.
The Digital Living Network Alliance (DLNA) is a
cross-industry organization of consumer electronics,
computing industry and mobile device companies.
Digital Living provides consumers with easy sharing
of digital media through your home network.
The DLNA certification logo makes it easy
to find products that comply with the DLNA
Interoperability Guidelines. This unit complies with
DLNA Interoperability Guidelines v1.5.
When a PC running DLNA server software or other
DLNA compatible device is connected to this unit,
some setting changes of software or other devices
may be required. Please refer to the operating
instructions for the software or device for more
information.
Certain System Requirements
For high definition video playback:
yy High definition display that has HDMI input jacks.
For Dolby® Digital Plus and DTS multi-channel
audio playback:
yy An amplifier/receiver with a built-in (Dolby
Digital, Dolby Digital Plus or DTS) decoder.
yy Main, centre, surround speakers and subwoofer
as necessary for chosen format.
For playing files on your PC’s share folder via your
home network, the PC requires below.
yy Windows® XP (Service Pack 2 or higher),
Windows Vista® (no Service Pack required)
Windows 7® (no Service Pack required)
yy 1.2 GHz Intel® Pentium® III or AMD
Sempron™ 2200+ processors
yy Network environment: 100 Mb Ethernet, WLAN
yy More than 1 folder on your PC has to be shared.
Visit suppot link of your operating system for
more information on file share settings.
Compatibility Notes
yy If you experience compatibility problems, please
contact an authorized Customer Service centre.
yy Dolby Digital Plus are supported with maximum
7.1 channels if you use HDMI connection for the
audio output of the unit.
Getting Started
11
Main Unit
a
b
c d
1
Getting Started
e
f
g h
a LAN port
e Power indicator
b HDMI OUT (1080p)
f Remote sensor
c OPTICAL AUDIO OUT
g USB port
d DC IN 12V (AC adapter input)
h RESET
Remote control
b m (MENU): Displays or exits
On-Screen Display.
g Colored (R, G, Y, B) buttons:
They are also used for [Smart
Share], [Premium], [LG Apps]
and [Web Browser] menu.
c Direction buttons: Selects
an option in the menu.
h d (Play): Starts playback.
d Centre buttons (Touch
Sensors): Enters the selected
item.
In web browser menu,
You can control displayed
cursor in all directions
using this button.
Note: If you leave the unit
without touching, the touch
function will be disabled for
energy saving. To activate
the touch function, press
direction button and touch
the sensors.
i c/v: Searches
backward or forward.
a 1 (POWER): Switches the
unit ON or OFF.
e HOME (n): Displays or exits
the Home Menu.
f BACK (x): Exits the menu
or resumes playback.
M (Pause): Pauses playback.
C/V: Press and hold for
two seconds to skip previous/
next chapter or file.
Z (Stop): Stops playback.
Battery Installation
Remove the battery cover on the
rear of the Remote Control, and
insert two R6 (size AA, alkaline)
batteries with 4 and 5 matched
correctly.
12
2
Connecting
Connecting the AC
Adapter
HDMI Connecting to
Your TV
Connect the unit to the power supply with the
supplied AC adapter.
Connect the power cord to the adapter, and then
plug the other end into an AC outlet.
If you have a HDMI TV or monitor, you can connect
it to this unit using a HDMI cable (Type A, High
Speed HDMI™ Cable). Connect the HDMI jack on
the unit to the HDMI jack on a HDMI compatible TV
or monitor.
Rear of the unit
Connecting
Rear of the unit
AC adapter
Plug into a
power source
HDMI cable
(not supplied)
AC power cord
yy Contact an electrical parts distributor for
assistance in selecting a suitable AC plug adapter
or AC cord set.
TV
>>Caution
Only use the AC adapter supplied with this
device. Do not use a power supply from
another device or another manufacturer. Using
any other power cable or power supply may
cause damage to the device and void your
warranty.
Set the TV’s source to HDMI (refer to TV’s Owner’s
manual).
,,Note
yy If you select a resolution manually and then
connect the HDMI jack to TV and your TV
does not accept it, the resolution setting is
set to [Auto].
yy If you select a resolution that your TV
does not accept, the warning message
will appear. After resolution change,
if you cannot see the screen, please
wait 20 seconds and the resolution will
automatically revert back to the previous
resolution.
yy The 1080p video output frame rate may
be automatically set to either 24 Hz or 50
Hz depending both on the capability and
preference of the connected TV.
Connecting
Additional Information for HDMI
Resolution Setting
yy When you connect a HDMI or DVI compatible
device make sure of the following:
The unit provides several output resolutions for
HDMI OUT. You can change the resolution using
[Setup] menu.
-- Try switching off the HDMI/DVI device and
this unit. Next, switch on the HDMI/DVI
device and leave it for around 30 seconds,
then switch on this unit.
13
1. Press HOME (n).
-- The connected device’s video input is set
correctly for this unit.
2
Connecting
-- The connected device is compatible with
720x576p, 1280x720p, 1920x1080i or
1920x1080p video input.
yy Not all HDCP-compatible HDMI or DVI devices
will work with this unit.
-- The picture will not be displayed properly
with non-HDCP device.
2. Press green (G) colored button. The [Setup]
menu appears.
,,Note
3. Use W/S to select [DISPLAY] option then
press D to move to the second level.
yy If a connected HDMI device does not accept
the audio output of the unit, the HDMI
device’s audio sound may be distorted or
may not output.
4. Use W/S to select the [Resolution] option
then press Centre button to move to the third
level.
yy When you use HDMI connection, you can
change the resolution for the HDMI output.
(Refer to “Resolution Setting” on page 13)
yy Select the type of video output from the
HDMI OUT jack using [HDMI Color Setting]
option on the [Setup] menu (see page 23).
yy Changing the resolution when the
connection has already been established
may result in malfunctions. To solve the
problem, turn off the unit and then turn it
on again.
yy When the HDMI connection with HDCP
is not verified, TV screen is changed to
black screen. In this case, check the HDMI
connection, or disconnect the HDMI cable.
yy If there is noise or lines on the screen, please
check the HDMI cable (length is generally
limited to 4.5 m(15 ft.)).
5. Use W/S to select the desired resolution then
press Centre button to confirm your selection.
14
Connecting
Connecting to an
Amplifier
Make one of the following connections, depending
on the capabilities of your existing equipment.
Connecting to an Amplifier via
HDMI Output
Connect the unit’s HDMI OUT jack to the
corresponding in jack on your amplifier using a
HDMI cable.
yy HDMI Audio connection (page 14)
yy Digital Audio connection (page 15)
2
Connecting
Since many factors affect the type of audio output,
see “Audio Output Specifications” on page 50 for
details.
Rear of the unit
About Digital Multi-channel sound
A digital multi-channel connection provides the
best sound quality. For this, you need a multichannel Audio/Video Receiver that supports one or
more of the audio formats supported by your unit.
Check the logos on the front of the Audio/Video
receiver and the manual. (PCM Stereo, Dolby Digital,
Dolby Digital Plus or DTS)
HDMI cable
Receiver/Amplifier
HDMI
cable
TV
Connect the amplifier’s HDMI output jack to HDMI
input jack on your TV using a HDMI cable if your
amplifier has HDMI output jack.
You will need to activate the unit’s digital output.
(See “[AUDIO] Menu” on page 24)
Connecting
15
Connecting to an Amplifier via
Digital Audio Output
Connect the unit’s OPTICAL AUDIO OUT jack to the
corresponding in jack (OPTICAL) on your amplifier
using an optional digital audio cable.
Rear of the unit
2
Connecting
Optical cable
OPTICAL
DIGITAL INPUT
Receiver/Amplifier
You will need to activate the unit’s digital output.
(See “[AUDIO] Menu” on page 24.)
16
Connecting
Connecting to your
Home Network
2
Connecting
This unit can be connected to a local area network
(LAN) via the LAN port on the rear panel or the
internal wireless module.
By connecting the unit to a broadband home
network, you have access to services such as
software updates, Web Browser and on-line content
services.
Router
Broadband
service
WAN
LAN 1
Wired network connection
Using a wired network provides the best
performance, because the attached devices
connect directly to the network and are not subject
to radio frequency interference.
Please refer to the documentation for your network
device for further instructions.
LAN 2
LAN 3
PC and/or DLNA
certified server
Connect the unit’s LAN port to the corresponding
port on your Modem or Router using a
commercially available LAN or Ethernet cable.
,,Note
yy When plugging or unplugging the LAN
cable, hold the plug portion of the cable.
When unplugging, do not pull on the LAN
cable but unplug while pressing down on
the lock.
yy Do not connect a modular phone cable to
the LAN port.
yy Since there are various connection
configurations, please follow the
specifications of your telecommunication
carrier or internet service provider.
yy If you want to access content from PCs or
DLNA servers, this unit must be connected
to the same local area network with them
via a router.
Rear of the unit
Connecting
Wired Network Setup
If there is a DHCP server on the local area
network (LAN) via wired connection, this unit will
automatically be allocated an IP address. After
making the physical connection, a small number
of home networks may require the unit’s network
setting to be adjusted. Adjust the [NETWORK]
setting as follow.
Preparation
1. Select [Connection Setting] option in the
[Setup] menu then press Centre button.
2. The [Connection Setting] menu appear on the
screen. Use W/S to select the [Wired] and
press Centre button.
3. Use W/S/A/D to select the IP mode
between [Dynamic] and [Static].
Normally, select [Dynamic] to allocate an IP
address automatically.
,,Note
If there is no DHCP server on the network and
you want to set the IP address manually, select
[Static] then set [IP Address], [Subnet Mask],
[Gateway] and [DNS Server] using W/S/A/
D.
4. Select [OK] and press Centre button to apply
network settings.
5. The unit will ask you to test the network
connection. Select [OK] and press Centre
button to complete the network connection.
6. If you select [Test] and press Centre button at
step 5 above, the network connection status is
displayed on the screen.
You can also test it on the [Connection Status]
in the [Setup] menu.
2
Connecting
Before setting the wired network, you need to
connect the broadband internet to your home
network.
17
18
Connecting
Wireless Network Connection
Another connection option is to use an Access Point
or a wireless router. The network configuration and
connection method may vary depending on the
equipment in use and the network environment.
2
Connecting
This unit is equipped with an IEEE 802.11n (Dualband, 5 GHz and 2.4 GHz band) wireless module,
which also supports the 802.11a/b/g standards.
For the best wireless performance, we recommend
using a IEEE 802.11n certified Wi-Fi network (access
point or wireless router).
,,Note
Available frequency range and channels for
5 GHz band are listed as below. But, there
may have the differences and restrictions
depending on the country. Try setting your
access point with other channel if you have
difficulties in wireless network connection.
Area
North
America
Europe
Others
Frequency Range
5.15-5.25 GHz (ch. 36-48),
5.725-5.825 GHz (ch. 149-161),
5.825-5.850 GHz (ch.165)
5.15-5.25 GHz (ch. 36-48)
5.15-5.25 GHz (ch. 36-48),
5.725-5.825 GHz (ch. 149-161),
5.825- 5.850 GHz (ch.165)
Wireless Network Setup
Wireless
Communication
PC and/or
DLNA certified server
Access Point or
Wireless Router
For the wireless network connection, the unit needs
to be set up for network communication. This
adjustment can be done from the [Setup] menu.
Adjust the [NETWORK] setting as follow. Setting up
the access point or the wireless router is required
before connecting the unit to the network.
Preparation
Before setting the wireless network, you need to:
-- Connect the broadband internet to the wireless
home network.
-- Set the access point or wireless router.
Broadband
service
Refer to the setup instructions supplied with
your access point or wireless router for detailed
connection steps and network settings.
For best performance, a direct wired connection
from this unit to your home network’s router or
cable/DSL modem is always the best option.
If you do chose to use the wireless option, note that
performance can sometimes be affected by other
electronic devices in the home.
-- Note the SSID and security code of the network.
1. Select [Connection Setting] option in the
[Setup] menu then press Centre button.
Connecting
2. The [Connection Setting] menu appear on the
screen. Use W/S to select [Wireless] and press
Centre button.
3. Select [Yes] and press Centre button to
continue. The new connection settings reset
the current network settings.
[Manual] – Your access point may not be
broadcasting its access point name (SSID).
Check your router settings through your
computer and either set your router to
broadcast SSID, or manually enter the access
point name (SSID) in [Manual].
[Push Button] – If your access point or
wireless router that supports the Push Button
Configuration method, select this option and
press the Push Button on your access point or
wireless router within 120 counts. You do not
need to know the access point name (SSID) and
security code of your access point or wireless
router.
5. Use W/S/A/D to select the IP mode
between [Dynamic] and [Static].
Normally, select [Dynamic] to allocate an IP
address automatically.
If you have security on your access point or
wireless router, verify that the WEP or WPA key
that was entered into the unit matches the
router’s information exactly. You need to input
the security code as necessary.
,,Note
yy WEP security mode generally have 4 keys
available on an access point or wireless
router’s setting. If your access point or
wireless router use WEP security, enter the
security code of the key “No.1” to connect
on your home network.
yy An Access Point is a device that allows you
to connect to your home network wirelessly.
yy If your access point or wireless router
supports the PIN Code configuration
method based on WPS(Wi-Fi Protected
Setup), press yellow (Y) colored button and
note the code number on the screen. And
then, enter the PIN number on a setting
menu of your access point or wireless router
to connect. Refer to the documentation for
your network device.
,,Note
If there is no DHCP server on the network and
you want to set the IP address manually, select
[Static] then set [IP Address], [Subnet Mask],
[Gateway] and [DNS Server] using W/S/A/
D and numerical buttons.
6. Select [OK] and press Centre button to apply
network settings.
7. The unit will ask you to test the network
connection. Select [OK] and press Centre
button to complete the network connection.
8. If you select [Test] and press Centre button at
step 7 above, the network connection status is
displayed on the screen. You can also test it on
the [Connection Status] in the [Setup] menu.
2
Connecting
4. The unit scans the all available access points or
wireless routers within range and display them
as a list. Use W/S to select an access point
or wireless router on the list, and then press
Centre button.
19
20 Connecting
Notes on Network Connection:
yy Many network connection problems during set
up can often be fixed by re-setting the router or
modem. After connecting the unit to the home
network, quickly power off and/or onnect the
power cable of the home network router or
cable modem. Then power on and/or connect
the power cable again.
2
Connecting
yy Depending on the internet service provider (ISP),
the number of devices that can receive internet
service may be limited by the applicable terms
of service. For details, contact your ISP.
yy The use of a “Router” may not be allowed or its
usage may be limited depending on the policies
and restrictions of your ISP. For details, contact
your ISP directly.
yy The wireless network operate at 2.4 GHz
radio frequencies that are also used by other
household devices such as cordless telephone,
Bluetooth® devices, microwave oven, and can be
affected by interference from them.
yy Turn off all unused network equipment in
your local home network. Some devices may
generate network traffic.
yy Our company is not responsible for any
malfunction of the unit and/or the internet
connection feature due to communication
errors/malfunctions associated with your
broadband internet connection, or other
connected equipment.
yy For the purpose of the better transmission,
placing the unit from the access point as close as
possible.
yy Some internet contents may require a higher
bandwidth connection.
yy Move closer to the access point if possible or reorient the unit so there is nothing between it
and the access point.
yy Even if the unit is properly connected and
configured, some internet contents may not
operate properly because of internet congestion,
the quality or bandwidth of your internet service,
or problems at the provider of the content.
yy Some internet connection operations may not
be possible due to certain restrictions set by the
Internet service provider (ISP) supplying your
broadband Internet connection.
yy Any fees charged by an ISP including, without
limitation, connection charges are your
responsibility.
yy A 10 Base-T or 100 Base-TX LAN port is required
for wired connection to this unit. If your internet
service does not allow for such a connection,
you will not be able to connect the unit.
yy You must use a Router to use xDSL service.
yy A DSL modem is required to use DSL service and
a cable modem is required to use cable modem
service. Depending on the access method of and
subscriber agreement with your ISP, you may not
be able to use the internet connection feature
contained in this unit or you may be limited to
the number of devices you can connect at the
same time. (If your ISP limits subscription to one
device, this unit may not be allowed to connect
when a PC is already connected.)
yy In some instances, placing the access point or
wireless router at least 0.45 m (1.5 ft.) above the
floor may improve the reception.
yy The reception quality over wireless depends on
many factors such as type of the access point,
distance between the unit and access point, and
the location of the unit.
yy Set your access point or wireless router to
Infrastructure mode. Ad-hoc mode is not
supported.
Connecting
USB device connection
This unit can play video, audio and photo files
contained in the USB device.
Playback content in the USB
device
1. Insert a USB device to the USB port until it fits
into place.
21
,,Note
yy This unit supports USB flash drive/external
HDD formatted in FAT16, FAT32 and NTFS
when accessing files (audio, photo, video).
yy This unit can support up to 8 partitions of
the USB device.
yy Do not extract the USB device during
operation (play, etc.).
yy USB device: USB device that supports
USB1.1 and USB2.0.
yy Movie, music and photo files can be played.
For details of operations on each file, refer
to relevant pages.
When you connect the USB device on the HOME
menu, the unit plays an audio file contained in the
USB storage device automatically. If the USB storage
device is containing various types of files, a menu
for the file type selection will appear.
File loading may takes few minutes depending on
the number of content stored in the USB storage
device. Press Centre button while [Cancel] is
selected to stop loading.
2. Press HOME (n).
3. Select [Smart Share] using A/D, and press
Centre button.
4. Select [Movie], [Photo] or [Music] using W/S,
and press Centre button.
5. Select [USB] option using W/S, and press
Centre button.
6. Select a file using W/S/A/D, and press d
or Centre button to play the file.
7. Withdraw the USB device carefully.
yy Regular back up is recommended to
prevent data loss.
yy If you use a USB extension cable, USB HUB
or USB Multi-reader, the USB device may not
be recognized.
yy Some USB device may not work with this
unit.
yy Digital camera and mobile phone are not
supported.
yy USB Port of the unit cannot be connected
to PC. The unit cannot be used as a storage
device.
2
Connecting
yy A USB device which requires additional
program installation when you have
connected it to a computer, is not
supported.
22 System Setting
Settings
[DISPLAY] Menu
TV Aspect Ratio
Adjust the Setup Settings
You can change the settings of the unit in the
[Setup] menu.
1. Press HOME (n).
Select a TV aspect ratio option according to your TV
type.
[4:3 Letter Box]
Select when a standard 4:3 TV is connected.
Displays theatrical images with masking bars
above and below the picture.
[4:3 Pan Scan]
Select when a standard 4:3 TV is connected.
Displays pictures cropped to fill your TV screen.
Both sides of the picture are cut off.
3
System Setting
[16:9 Original]
2. Press green (G) colored button. The [Setup]
menu appears.
Select when a 16:9 wide TV is connected. The
4:3 picture is displayed with an original 4:3
aspect ratio, with black bars appearing at the
left and right sides.
[16:9 Full]
Select when a 16:9 wide TV is connected. The
4:3 picture is adjusted horizontally (in a linear
proportion) to fill the entire screen.
3. Use W/S to select the first setup option, and
press D to move to the second level.
4. Use W/S to select a second setup option, and
press Centre button or D to move to the third
level.
5. Use W/S to select as desired setting, and
press Centre button or D to confirm your
selection.
,,Note
You cannot select [4:3 Letter Box] and
[4:3 Pan Scan] option when the resolution is
set to higher than 720p.
System Setting 23
Resolution
HDMI Color Setting
Sets the output resolution of the Component and
HDMI video signal. Refer to page 13 for details about
the resolution setting.
Select the type of output from the HDMI OUT jack.
For this setting, please refer to the manuals of your
display device.
[Auto]
[YCbCr]
If the HDMI OUT jack is connected to
TVs providing display information (EDID),
automatically selects the resolution best suited
to the connected TV.
Select when connecting to a HDMI display
device.
[1080p]
[RGB]
Select when connecting to a DVI display
device.
Outputs 1080 lines of progressive video.
Wallpaper
Outputs 1080 lines of interlaced video.
Changes the background of the initial screen.
[720p]
Outputs 720 lines of progressive video.
[LANGUAGE] Menu
[576p]
Display Menu
Outputs 576 lines of progressive video.
Select a language for the [Setup] menu and onscreen display.
1080p Display Mode
When the resolution is set to 1080p, select
[24 Hz] for smooth presentation of film material
(1080p/24 Hz) with a HDMI-equipped display
compatible with 1080p/24 Hz input.
,,Note
yy When you select [24 Hz], you may
experience some picture disturbance when
the video switches video and film material.
In this case, select [50 Hz].
yy Even when [1080p Display Mode] is set to
[24 Hz], if your TV is not compatible with
1080p/24 Hz, the actual frame frequency of
the video output will be 50 Hz to match the
video source format.
3
System Setting
[1080i]
24 System Setting
[AUDIO] Menu
Set the unit’s Audio options according to the type
of audio system you use.
,,Note
Since many factors affect the type of audio
output, see “Audio Output Specifications” on
page 44 for details.
HDMI / Digital Output
[PCM Stereo]
3
Select if you connect this unit’s HDMI OUT or
DIGITAL AUDIO OUT jack to a device with twochannel digital stereo decoder.
System Setting
[DTS Re-Encode]
Select if you connect this unit’s HDMI OUT or
DIGITAL AUDIO OUT jack to a device with DTS
decoder.
[Primary Pass-Thru]
Select if you connect this unit’s OPTICAL AUDIO
OUT and HDMI OUT jack to a device with
LPCM, Dolby Digital, Dolby Digital Plus and DTS
decoder.
Sampling Freq.
(Digital Audio Output)
[192 kHz]
Select this if your A/V Receiver or Amplifier is
capable of handling 192 kHz signals.
[96 kHz]
Select this if your A/V Receiver or Amplifier is
not capable of handling 192 kHz signals. When
this choice is made, this unit
automatically converts any 192 kHz signals to
96 kHz so your system can decode them.
[48 kHz]
Select this if your A/V Receiver or Amplifier is
not capable of handling 192 kHz and 96 kHz
signal. When this choice is made, this unit
automatically converts any 192 kHz and 96 kHz
signals to 48 kHz so your system can decode
them.
Check the documentation for your A/V Receiver or
Amplifier to verify its capabilities.
DRC (Dynamic Range Control)
This function allows you to listen to a movie at a
lower volume without losing clarity of sound.
[Off]
Turns off this function.
[On]
Compress the dynamic range of the Dolby
Digital or Dolby Digital Plus audio output.
[Auto]
The dynamic range of the Dolby Digital and
Dolby Digital Plus are operated as same as the
[On] mode.
,,Note
The DRC setting can be changed only when
the unit is in complete stop mode.
System Setting 25
[NETWORK] Menu
[OTHERS] Menu
The [NETWORK] settings are needed to use the
software update, Web Browser and on-line content
services.
DivX® VOD
Connection Setting
If your home network environment is ready to
connect the unit, the unit needs to be set the
wired or wireless network connection for network
communication. (See “Connecting to your Home
Network” on pages 16.)
Connection Status
Wi-Fi Direct
This player is a Wi-Fi Direct™ certified device. Wi-Fi
Direct™ is the technology that devices to connect
each other without connecting to an Access point
or a router. Set this option to [On] for activating the
Wi-Fi Direct™ mode. Refer to page 29 for the device
connection.
Premium/LG Apps
[Country Setting]
Select your area for displaying proper services
and contents on the [Premium] and [LG Apps]
feature.
[ID Management]
Displays the [ID Management] menu. You can
manage IDs that ever logged-in on this unit.
[Registration Code]
Display the unique code of this unit for
servicing [Premium] and [LG Apps] feature.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX
Certified® device must be registered in order to play
purchased DivX Video-on-Demand (VOD) movies.
To obtain your registration code, locate the DivX
VOD section in your device setup menu. Go to vod.
divx.com for more information on how to complete
your registration.
[Register]
Displays the registration code of your unit.
[Deregister]
Deactivate your unit and display the
deactivation code.
,,Note
All the downloaded videos from DivX VOD
with this unit’s registration code can only be
played back on this unit.
Auto Power Off
The screen saver appears when you leave the unit
in Stop mode for about five minutes. If you set
this option to [On], the unit automatically turns
off within 25 minutes since the Screen Saver is
displayed. Set this option to [Off ] to leave the
screen saver until the unit is operated by the user.
3
System Setting
If you want to check the network status on this unit,
select the [Connection Status] options and press
Centre button to check whether a connection
to the network and the internet have been
established.
ABOUT DIVX VIDEO: DivX® is a digital video format
created by DivX, Inc. This is an official DivX Certified®
device that plays DivX video. Visit divx.com for more
information and software tools to convert your files
into DivX video.
26 System Setting
Factory Set
You can reset the unit to its original factory settings.
,,Note
If you reset the unit to its original factory
settings using [Factory Set] option, you have
to set all the activation for the on-line services
and network settings again.
Software
[Information]
Displays the current software version.
3
[Update]
System Setting
You can update the software by connecting
the unit directly to the software update server
(see page 46).
Disclaimer Notice
Press Centre button to view the notice of Network
Service Disclaimer.
Pointer
You can adjust the pointer speed.
Network Play
This function allows you to control the playback
of media streamed from DLNA media server by a
DLNA certified smartphone. Most DLNA certified
smartphone has a function to control the playback
media on your home network. Set this option to
[On] for allowing your smartphone to control this
unit. Refer to instructions of your DLNA certified
smartphone or the application for more detailed
information.
Operating 27
General Playback
Using [HOME] menu
The home menu appears when you press HOME
(n). Use W/S/A/D to select a category and
press Centre button.
Playing a file media from a
USB device
This unit can play video, audio and photo files
contained in the USB device.
1. Insert a USB device into the USB port until it fits
into place.
2. Press HOME (n).
3. Select [Smart Share] using A/D, and press
Centre button.
4
5. Select [USB] option using W/S, and press
Centre button.
a [Premium] - Displays the Premium Home or
[Edit Premium Card] screen.
b [LG Apps] - Displays the [LG Apps] screen.
c [Web Browser] - Displays the Browser Home
screen.
d [Sign In] - Displays the [Premium] or [LG
Apps] Login menu screen.
e [Setup] - Adjusts the system settings.
f [Smart Share] - Plays [Movie], [Photo],
[Music] or [Media Link] contents.
g [Search] - This function will be updated later.
h [LG Apps] - Displays the [LG Apps] screen.
i [Favorite Apps] - Shortcut for user’s favorite
Apps.
j [My Apps] - Display the [My Apps] screen.
6. Select a file using W/S/A/D, and press d
or Centre button to play the file.
Operating
4. Select [Movie], [Photo] or [Music] using W/S/
A/D, and press Center button.
28 Operating
Playing a file media from a
network server
This unit can play video, audio and photo files
located in a PC or a DLNA server through your
home network.
1. Check the network connection and settings
(page 16).
2. Press HOME (n).
3. Select [Movie], [Photo] or [Music] using W/S,
and press Centre button.
4. Select a DLNA media server or a share folder
on your PC on the list using W/S, and press
Centre button.
4
Entering a network user ID and the
password
Depending on your PC’s environment, you may
need to enter a network user ID and the password
for accessing a shared folder.
1. The keyboard menu appears automatically if the
network user ID and the password are required.
2. Use W/S/A/D to select a character then
press Centre button to confirm your selection
on the virtual keyboard.
To enter a letter with an accent mark, press m
(MENU) to display the extended character set.
Operating
[Cancel] – Clear all entered characters.
[Space] – Inserts a space at the cursor position.
If you want to rescan available media server,
press the green (G) colored button.
5. Select a file using W/S/A/D, and press
Centre button to play the file.
,,Note
yy The file requirements are described on page
8.
yy The thumbnail of the unplayable files can
be displayed, but those cannot be played
on this unit.
yy The subtitle file name and video file name
have to be the same and located at the
same folder.
yy The playback and operating quality may be
affected by your home network condition.
yy You may experience connection problems
depending on your server’s environment.
[<–] – Deletes the previous character at the
cursor position.
[ABC / abc / #+-=&] – Change the keyboard
menu settings to capital letters, small letters or
symbols.
3. When you finish entering the network user ID
and password, select [OK] using W/S/A/D
and press Centre button to access the folder.
The network user ID and password will be
remembered after accessing the folder for your
convenience. If you do not want the network user
ID and password to be remembered, press red (R)
colored button to un-tick the [Remember] check
box before accessing the folder.
Operating 29
Wi-Fi Direct™ Connection
Connecting to a Wi-Fi Direct™
certified device
6. Select a server that shared from the connected
Wi-Fi Direct™ device using W/S, and press
Center button to navigate the server.
This player can play movie, music and photo files
located in a Wi-Fi Direct™ certified device. The Wi-Fi
Direct™ technology make the player to be directely
connected to a Wi-Fi Direct™ certified device
without connecting to a network device such as an
access point.
1. Set the [Wi-Fi Direct] option on the [Setup]
menu to [On] (page 25).
2. Press HOME (n).
3. Select [Movie], [Photo] or [Music] using W/S/
A/D, and press Center button.
4. Select [Wi-Fi Direct] option using W/S, and
press Center button.
To select a server from the device list, files or
folders must be shared by DLNA server from the
connected Wi-Fi Direct™ device.
7. Select a file using W/S/A/D, and press
Center button to play the file.
,,Note
yy For the purpose of the better transmission,
placing the player from the Wi-Fi Direct™
certified server as close as possible.
5. Select a Wi-Fi Direct™ device on the list using
W/S, and press Center button.
Wi-Fi Direct™ connection will be automatically
proceeded.
If the Wi-Fi Direct™ device supports the PIN
Code configuration method based on WPS(WiFi Protected Setup), select a device on the list
and press yellow (Y) coloured button. Note the
PIN number on the screen. And then, enter the
PIN number on a setting menu of the device to
connect.
If you want to rescan available Wi-Fi Direct™
device, press the green (G) coloured button.
yy If you try to connect wireless network while
a device is connected by Wi-Fi Direct™
function , Wi-Fi Direct™ connection will be
force disconnected.
yy If this player and a Wi-Fi Direct™ device
are connected to the different local area
network, Wi-Fi Direct™ connection may not
available.
Operating
yy This unit can connect only 1 device at a
time. Multiple connection is not available.
4
30 Operating
Connecting to a Wi-Fi available
devices
This player can connect to a general Wi-Fi device
using Wi-Fi Direct™ function.
8. Select a server that shared from the connected
Wi-Fi device using W/S, and press Center
button to navigate the server.
1. Set the [Wi-Fi Direct] option on the [Setup]
menu to [On] (page 25)
2. Press HOME (n).
3. Select [Movie], [Photo] or [Music] using A/D,
and press Center button.
4. Select [Wi-Fi Direct] option using W/S, and
press Center button.
To select a server from the device list, files or
folders must be shared by DLNA server from the
connected device.
9. Select a file using W/S/A/D, and press
Center button to play the file.
4
Operating
5. Press red (R) coloured button to display the
[Network name (SSID)], [Security Option] and
[Encription] of the player.
6. On your Wi-Fi device, make a network
connection to this player, using [Network name
(SSID)], [Security Option] and [Encription] at
step 5 above.
7. Press BACK (x) twice to display the device list.
Operating
Basic operations for video and
audio content
Basic operations for photo
content
To stop playback
To play a slide show
Press Z (STOP) while playback.
Press d (PLAY) to start slide show.
To pause playback
To stop a slide show
Press M (PAUSE) while playback.
Press d (PLAY) to resume playback.
Press Z (STOP) while slide show.
To play frame-by-frame (Video)
Press M (PAUSE) while movie playback.
Press M (PAUSE) repeatedly to play Frame-by-Frame
playback.
To scan forward or backward
31
To pause a slide show
Press M (PAUSE) while slide show.
Press d (PLAY) to re-start the slide show.
To skip to the next/previous photo
While viewing a photo in full screen, press A or D
to go to the previous or next photo.
Press c or v to play fast forward or fast reverse
during playback.
To slow down the playing speed
While the playback is paused, press v repeatedly
to play various speeds of slow motion.
To skip to the next/previous file
During playback, press C or V and hold for
two seconds to go to the next file or to return to
the beginning of the current track/file.
Press C twice briefly to step back to the previous
file.
In the file list menu of a server, there may be many
types of contents in a folder together. In this case,
press C or V and hold for two seconds to go
to the previous or next content with same type.
4
Operating
You can change the various playback speeds by
pressing c or v repeatedly.
32 Operating
Advanced Playback
Changing content list view
Zoom in & out during slide
show
Method 1
1. During playback, press m (MENU) to display the
option menu.
On the [Movie], [Music] or [Photo] menu, you can
change the content list view.
Press red (R) colored button repeatedly.
2. Select the [Zoom] option using W/S, and
press Centre button to display the [Zoom]
menu.
3. Use red (R) or green (G) colored button to zoom
out or in the picture. You can move through the
zoomed picture using W/S/A/D buttons.
4. To return to the normal picture size, press yellow
(Y) colored button.
5. Press BACK (x) to exit the [Zoom] menu.
4
Repeat Playback
Operating
During playback, press red (R) colored button
repeatedly to select a desired repeat mode.
Music files
;Track– The current track or file will be played
back repeatedly.
:All – All the tracks or files will be played back
repeatedly.
l – The tracks or files will be played back in
random order.
l:All – All the tracks or files will be played
back repeatedly in random order.
To return to normal playback, press red (R) colored
button repeatedly to select [Off ].
Viewing content information
Method 2
The unit can display the content information.
1. On the content list, press m (MENU) to display
the option menu.
1. Select a file using W/S/A/D.
2. Press m (MENU) to display the option menu.
3. Select the [Information] option using W/S,
and press Centre button.
The file information appears on the screen.
,,Note
The information displayed on the screen
may not correct comparing actual content
information.
2. Use W/S to select the [View Change] option.
3. Press Centre button to change the content list
view.
Operating 33
Selecting a subtitle file
Options while viewing a photo
If the subtitle file name is different from the video
file name, you need to select the subtitle file on the
[Movie] menu before playing the movie.
You can use various options during viewing a
photo in full screen.
1. Use W/S/A/D to select the subtitle file you
wish to play in the [Movie] menu.
2. Press Centre button.
1. While viewing a photo in full screen, press m
(MENU) to display the option menu.
2. Select an option using W/S.
a Current photo/Total number of photos
– Use A/D to view previous/next photo.
,,Note
b Slide Show – Press Centre button to start
or pause slide show.
yy If you press Z (STOP) while playback, the
subtitle selection is cancelled.
yy This function is not available for playing file
on a server via home network.
Setting your photo as a
wallpaper
You can apply your photo to the wallpaper.
1. Press HOME (n).
2. Select [Smart Share] using A/D, and press
Centre button.
3. Select [Photo] using W/S, and press Centre
button.
4. Select [USB] option using W/S, and press
Centre button.
5. Select a photo file, and press m (MENU) to
display the option menu.
6. Use W/S to select [Wallpaper], and press
Centre button.
7. Use A/D to select [Yes], and press Centre
button to be applied.
The photo will be set as [Wallpaper 5] on the
[Setup] menu.
c Music Select – Select the background
music for the slide show (page 34).
d Music –Press Centre button to start or
pause background music.
e Rotate – Press Centre button to rotate
the photo clockwise.
f Zoom – Press Centre button to display
the [Zoom] menu.
g Effect – Use A/D to select a transition
effect between photos in a slide show.
h Speed – Use A/D to select a delaying
speed between photos in a slide show.
3. Press BACK(x) to exit the option menu.
4
Operating
Press Centre button again to deselect the
subtitle file. Selected subtitle file will be
displayed when you play the video file.
34 Operating
Listening to music while slide
show
On-Screen display
You can display photo files while listening to audio
files.
You can display and adjust various information and
settings about the content.
1. While viewing a photo in full screen, press m
(MENU) to display the option menu.
2. Use W/S to select [Music Select] option, and
press Centre button to display the [Music
Select] menu.
3. Use W/S to select a device, and press Centre
button.
Displaying content information
on-screen
1. While playback, press m (MENU) to show
various playback information.
Device that you can select are differ depending
on the location of the photo file you are
displaying in full screen.
Photo location
4
Available Device
USB
USB
Share Folder (PC)
Share Folder (PC)
DLNA server
DLNA server
Operating
4. Use W/S to select a file or a folder you wish to
play.
a Title – current title number/total number of
titles
b Time – elapsed playing time/total playback
time
c Audio – selected audio language or channel
d Subtitle – selected subtitle.
Select g and press Centre button to display
the upper directory.
,,Note
When selecting the audio file from a server,
folder selection is not available. Only file
selection is available.
5. Use D to select [OK], and press Centre button
to complete music selection.
e Code Page – selected subtitle code page
(page 33).
f TV Aspect Ratio – selected TV aspect Ratio.
g Picture Mode – selected picture mode.
2. Select an option using W/S.
3. Use A/D to adjust the selected option value.
4. Press BACK(x) to exit the On-Screen display.
,,Note
yy If no button is pressed for a few seconds,
the on-screen display disappears.
yy Available items may differ depending on
titles.
Operating 35
Playing from selected time
Changing TV Aspect Ratio
1. Press m (MENU) during playback. The time
search box shows the elapsed playing time.
You can change the TV aspect ratio setting while
playback.
2. Select the [Time] option and then input the
required start time in hours, minutes, and
seconds from left to right.
1. During playback, press m (MENU) to display the
On-Screen display.
For example, to find a scene at 2 hours, 10
minutes, and 20 seconds, enter “21020”.
Press A/D to skip the playback 60 seconds
forward or backward.
3. Press Centre button to start playback from
selected time.
,,Note
yy This function may not work on some titles.
yy This function may not work depending on
the file type and ability of the DLNA server.
1. During playback, press m (MENU) to display the
On-Screen display.
2. Use W/S to select the [Audio] option.
3. Use A/D to select desired audio language,
audio track or audio channel.
,,Note
Immediately after you have switched sound,
there may be a temporary discrepancy
between the display and actual sound.
Selecting a subtitle language
1. During playback, press m (MENU) to display the
On-Screen display.
2. Use W/S to select the [Subtitle] option.
3. Use A/D to select desired subtitle language.
4. Press BACK(x) to exit the On-Screen display.
3. Use A/D to select desired option.
4. Press BACK(x) to exit the On-Screen display.
,,Note
Even if you change the value of the [TV Aspect
Ratio] option in On-Screen display, the [TV
Aspect Ratio] option in the [Setup] menu is
not changed.
Changing subtitle code page
If the subtitle is displayed in broken letter, you can
change the subtitle code page to view the subtitle
file properly.
1. During playback, press m (MENU) to display the
playback menu.
2. Use W/S to select the [Code Page] option.
3. Use A/D to select desired code option.
4. Press BACK(x) to exit the On-Screen display.
4
Operating
Listening to a different audio
track
2. Use W/S to select the [TV Aspect Ratio]
option.
36 Operating
Changing Picture Mode
You can change the [Picture mode] option while
playback.
1. During playback, press m (MENU) to display the
On-Screen display.
Using the Premium
You can use various content services via Internet
with the Premium feature.
2. Use W/S to select the [Picture Mode] option.
1. Check the network connection and settings
(page 16).
3. Use A/D to select desired option.
2. Press HOME (n).
4. Press BACK(x) to exit the On-Screen display.
3. Select the [Premium] using A/D, and press
Centre button.
Setting the [User setting] option
1. During playback, press m (MENU) to display the
On-Screen display.
2. Use W/S to select the [Picture Mode] option.
3. Use A/D to select the [User setting] option,
and press Centre button.
4
Operating
4. Select an on-line service using W/S/A/D,
and press Centre button.
,,Note
yy Detailed information of each service,
contact to the content provider or visit
support link of the service.
4. Use W/S/A/D to adjust the [Picture Mode]
options.
Select [Default] option then press Centre
button to reset the all video adjustments.
5. Use W/S/A/D to select the [Close] option,
and press Centre button to finish setting.
yy The content of Premium services and
service related information, including user
interface, is subject to changes. Please refer
to the web site of each service for most upto-date information.
yy Using Premium features with wireless
network connection may result in improper
streaming speed by interference from
household devices that are using radio
frequencies.
yy When you are first time to access [Premium]
or [LG Apps] feature, current country setting
appears. If you want to change the country
setting, select [Edit] and press Centre
button.
Operating 37
Using the LG Apps
You can use the LG application services on this
unit via Internet. You can easily find and download
various applications from LG Apps store.
1. Check the network connection and settings
(page 16).
Depending on the region, LG Apps service
may not available at the moment. LG Apps
service will be opened for such regions by
software updates later.
2. Press HOME (n).
3. Select the [LG Apps] using A/D, and press
Centre button.
Signing in
To use the [LG Apps] feature, you need to sign in
with your account.
1. On the [LG Apps] or [My Apps] screen, press red
(R) colored button.
2. Fill the [ID] and [Password] field using the virtual
keyboard.
If you do not have an account, press red (R)
colored button to register.
3. Use W/S/A/D to select [OK], and press
Centre button to sign in with your account.
If you select the [Auto Sign In] check box,
your ID and password are remembered and
automatically signed in without entering them.
,,Note
yy If you want to sign in with other account,
press red (R) colored button on [LG Apps] or
[My Apps] screen, and select [Change User]
option.
4. Select a category using A/D, and press
Centre button.
Managing my Apps
5. Use W/S/A/D to select an application, and
press Centre button to display the information.
You can move or delete an installed application in
the [My Apps] menu.
6. Press Centre button while [Install] icon is
highlighted. The application will be installed to
the unit.
Move an application
To install an application to the unit, user needs
to sign in. Refer to page 37 for more information
of signning in.
1. Select an application, and press green (G)
colored button to display the options.
2. Use W/S to select [Move], and press Centre
button.
7. Press yellow (Y) colored button to display the
[My Apps] screen.
3. Use W/S /A/D to select a position you
want to move to, and press Centre button.
8. Select the installed application and press
Centre button to excute it.
Delete an application
,,Note
To install a paid application, you need to be
a paid member. Visit www.lgappstv.com for
more information.
1. Select an application, and press green (G)
colored button to display the options.
2. Use W/S to select [Delete], and press Centre
button.
3. Use A/D to select [Yes], and press Centre
button to confirm.
4
Operating
yy To view the information of your account and
applications, press red (R) colored button on
[LG Apps] or [My Apps] screen, and select
[Account Setting] option.
38 Operating
Using the Browser
Home
You can browse, search web pages using the web
browser feature over the Internet.
,,Note
About the Browser Home
menu
There are various options on the Browser Home
menu. Use W/S/A/D to select an option
and press Centre button to select the options as
described below.
yy Web browser on this unit is different
with a web browser on your PC. The web
browser on this unit does not support
additional plug-ins and platform-dependant
technology such as ActiveX.
yy Compatible Flash version on this unit is up
to Flash 8.
yy Playing a movie on the web browser can be
restricted depending on a movie source.
yy The web browser will be forced to quit
when the unit runs out of memory.
4
Operating
1. Check the network connection and settings
(page 16).
2. Press HOME (n).
3. Select the [Web Browser] using A/D, and
press Centre button.
Options available within the browser menu include.
a URL – You can find a web page entering a
web site address. The virtual keyboard will be
displayed and enter a web address.
b Favorites – You can directly open your
favorites web pages without entering web
address.
c History – Displays web address list of
previously opened web pages. Use W/S to
select a website address, and press Centre
button to open the web page.
Press the red (R) colored button to clear
history.
4. Select an web page using W/S/A/D, and
press Centre button.
,,Note
Press S and W/S/A/D to select the
desired web page in the web browser menu.
Press Centre button to enter the web page.
Operating 39
Editing your favorite web
pages
In the Favorites menu , you can edit your favorites.
1. Press red (R) colored button to change the
highlighter to edit mode.
Additional browser options
There are various options on the browser menu.
Press the corresponding remote buttons to use the
options. You can also move the pointer and click
the buttons to use the options.
2. The highlighter colour will be changed to green
colour.
3. Select a web page and press Centre button to
display the [Edit] menu.
a Returns to previous page.
b Returns to Browser Home menu.
4. Use W/S to select an option and press Centre
button.
c You can zoom in and out the currently
viewing page.
[Rename] - Edits the selected web page name.
The virtual keyboard will be displayed.
e Searches web pages from Google by
entering a keyword.
[Delete] - Deletes the web page from favorites
menu.
f Display the browser menu.
[Close] - Exits the edit menu
[,//] - Moves to the previous or next web
page.
[Refresh] - Reloads the current web page.
[Settings] - To clear the saved data such as
cookies and history, select this and select an
option from the menu.
4
Operating
[Move] - Moves the web page to desired
position in the favorites menu.
d Saves current page to your favorites web
page. The virtual keyboard will be displayed.
40 Operating
Playing content via
Media Link
You can enjoy music, photo, or video by installing
the PLEX application on your PC via home network.
,,Note
yy To enjoy Media Link, install PLEX Midea
server version on the MAC or PC higher
than 0.9.1.14. (You can download it from
http://www.plexapp.com/medialink )
yy For the Thai, Arabic, Persian, Hebrew,
Kurdish, GUI language is shown in English,
carried data is not displayed it.
4
yy When plays the Video Plug-in, initial
buffering may take a long time for the
unsupported media. Depending on the
ability of PC or network speed, the ability of
conversion operations on the PC may differ.
Operating
yy The file requirements are described on page
8.
yy Using Media Link with wireless network
connection may result in improper playback
quality by interference from household
devices that are using radio frequencies.
yy Your PC may not be recognized on this
unit depending on the router settings.
(Ex.: On some router, when setting “Multi
Cast forward“ function, your PC may not
be recognised on the unit with wireless
network connection.)
yy Since encoding format of character string is
supported only for UTF files, Text files that
are not UTF types may not be supported.
yy When you play the Saved files (Movie, TV
show, Music) on the PC, the supported
formats are MP4, ASF, WMV, MP3, WMA.
yy When playing the music file, fast forward
and backward playback is not supported.
Mide Link connection
Check the network connection and settings (page
16).
1. Install PLEX application on your PC.
You can download it from http://www.plexapp.
com/medialink.
2. Run PLEX on your PC.
If it is first run, you can set it easily through
WIZARD.
,,Note
yy Local contents can always be revised
through Media Manager.
yy Web contents can be installed or deleted in
the online menu of the PLEX.
Operating
41
Using the Media Link
Using Movie section
1. Press HOME (n).
You can watch movie or view movie information on
the movie section.
2. Select the [Media Link] using W/S/A/D,
and press Center button.
List of Media Link available PCs on your home
network are displayed.
3. Use W/S/A/D to select a PC and press
Center button to display the options as
described below.
1. Press HOME (n).
2. Select the [Media Link] using W/S/A/D,
and press Center button.
3. Select an movie section using A/D, and press
Center button.
4
b Those are (plug- in) options. You can use online content by operating the set plug-in.
c Selects other devices.
You can also use green (G) button on the
remote control.
d You can install, delete or update the desired
applications on your PC.
You can also use yellow (Y) button on the
remote control.
e Moves to the previous screen.
a Shows movie information you select.
b Shows the thumbnail of movies.
c Searches for a movie within the section.
You can also use red (R) button on the
remote control.
d Shows a reorganized list that matches your
property of selection. You can also use green
(G) button on the remote controller.
e Plays a movie in full screen. If you were
watching movie, it resumes playback.
f Moves to the previous screen.
You can also use BACK(x) on the remote
control.
,,Note
Subtitle language is work depending on the
menu language.
Operating
a It is section list set on the connected PC. You
can enjoy media to section.
42 Operating
Using Music section
Using TV Program section
You can listen to music or view the file information
on the music section.
You can enjoy the TV program or view program
information on the TV program section.
1. Press HOME (n).
1. Press HOME (n).
2. Select the [Media Link] using W/S/A/D,
and press Center button.
2. Select the [Media Link] using W/S/A/D,
and press Center button.
3. Select a music section using A/D, and press
Center button.
3. Select an TV program section using A/D, and
press Center button.
a Shows the list of music file in the music
section.
a Shows the list of TV programs in the TV
program section.
4
Operating
b Shows selected music information.
b Shows selected program information.
c Searches for music within the section. You
can also use red (R) button on the remote
control.
c Searches for TV program within the section.
You can also use red (R) button on the
remote control.
d Shows selected music.
d Shows selected TV program.
e Shows a reorganized list that matches your
property of selection. You can also use green
(G) button on the remote control.
e Shows a reorganized list that matches your
property of selection. You can also use green
(G) button on the remote controller.
f Moves to the previous screen.
You can also use BACK(x) on the remote
control.
f Moves to the previous screen.
You can also use BACK(x) on the remote
control.
Operating 43
Plug-in installation
You can enjoy a various media on the web by
installing the plug-in.
1. Press HOME (n).
2. Select the [Media Link] using W/S/A/D,
and press Center button.
3. Select a Plug-in section using A/D, and press
Center button.
4
b If you move the pointer to plug-in you want,
the information of plug-in will be displayed.
In case of installed plug-in: it can be run,
update, reinstalled or deleted.
In case of uninstalled plug-in: it can be
installed
The installed plug-ins can be run from the
video, music or picture plug-in.
c Moves to the previous screen.
You can also use BACK(x) on the remote
control.
,,Note
Some plug-in may not work properly.
Operating
a Shows available plug-in list.
44 Troubleshooting
Troubleshooting
General
Symptom
Cause & Solution
No Power.
yy Plug the power cord into the wall outlet securely.
Cannot play movie, photo or
audio files.
yy The files are not recorded in a format that the unit can play.
The remote control does not
work properly.
yy The remote control is not pointed at the remote sensor of the unit.
yy The unit does not support the codec of the video file.
yy The remote control is too far from the unit.
yy There is an obstacle in the path of the remote control and the unit.
yy The batteries in the remote control are exhausted.
yy We recommend using alkaline batteries.
The connected USB storage
device is not recognized.
yy Try another different USB cable, some of USB cable may not support
enough current for normal USB operation.
yy If you use a USB extension cable or USB HUB, the USB devices may not
be recognized.
yy An USB device which requires additional program installation when
you have connected it to a computer is not supported.
yy This unit supports only USB Flash Drive and USB External HDD with
FAT16, FAT32 or NTFS format.
5
Troubleshooting
Picture
Symptom
Cause & Solution
There is no picture.
yy Select the appropriate video input mode on the TV so the picture
from the unit appears on the TV screen.
yy Check the [HDMI Color Setting] in the [Setup] menu is set to the
appropriate item that conforms to your video connection.
yy Your TV may not suppot the resolution you have set on the unit.
Change the resolution that your TV accepts.
yy The player’s HDMI OUT jack is connected to a DVI device that does
not support copyright protection.
Picture noise appears
yy Set the resolution which your TV accepts.
Troubleshooting 45
Resetting
Symptom
Cause & Solution
You can reset the unit as
follows.
yy Press RESET button on the unit. This will force the unit to power off.
yy Unplug the power cord, wait at least five seconds, and then plug it in
again.
Network
Symptom
Cause & Solution
Streaming video services (such as
YouTube™, etc.) are often stopped
or “buffer” during playback.
yy Your broadband service speed may not be fast enough to stream
video services. Contact your Internet Service Provider (ISP) and
increase the broadband speed is recommended.
Shared folder or files from your
PC or a media server are not
displayed on the device list.
yy The fire wall or anti-virus software on your media server is running.
Turn off the fire wall or anti-virus software running on your PC or
media server.
yy The unit is not connected to the local area network that your PC or
the media server are connected.
yy The wireless communication may be interrupted from household
devices that are using radio frequencies. Move the unit away from
them.
Access point is not displayed on
the “Access point name” list.
yy The access point or wireless LAN router may not broadcast its SSID.
Set your access point to broadcast its SSID through your computer.
yy Your network device such as access point may not set with
available frequency range and channel that this unit can support.
Try setting the frequency range and channel on the network
device setting.
Customer Support
You can update the Unit using the latest software to enhance the products operation and/or add new
features. To obtain the latest software for this unit (if updates have been made), please visit
http://us.lgservice.com or contact LG Electronics customer care centre.
Open source software notice
To obtain the corresponding source code under GPL, LGPL and other open source licenses, please visit
http://opensource.lge.com. All referred license terms, warranty disclaimers and copyright notices are
available to download with the source code.
5
Troubleshooting
Cannot connect the unit to the
access point or wireless LAN
router.
46 Appendix
Network Software
Update
Network update notification
From time to time, performance improvements
and/or additional features or services may be
made available to units that are connected to a
broadband home network. If there is new software
available and the unit is connected to a broadband
home network, the unit will inform you about the
update as follows.
Option 1:
1. The update menu will appear on the screen
when you turn on the unit.
2. Use A/D to select a desired option and then
press Centre button.
Software Update
You can update the unit using the latest software
to enhance the products operation and/or add
new features. You can update the software by
connecting the unit directly to the software update
server.
,,Note
yy Before updating the software in your unit,
remove USB Device from the unit.
yy Before updating the software in your unit,
turn the unit off and then turn it back on.
yy During the software update procedure,
do not turn off the unit or disconnect AC
power, or do not press any button.
yy If you cancel the update, turn off the power
and turn it on for stable performance.
yy This unit cannot be updated to previous
software version.
1. Check the network connection and settings
(page 16).
2. Select [Software] option in the [Setup] menu
then press Centre button.
6
Appendix
[OK]
Starts the software update.
[Cancel]
Exits the update menu and
displays it next booting.
[Hide]
Exits the update menu and
it does not appear until next
software is uploaded in the
update server.
Option 2:
If the software update is available from the update
server, the “Update” icon appears in the Home
menu. Press blue (B) colored button to start the
update procedure.
3. Select [Update] option, and press Centre
button.
The unit will check for the newest update.
,,Note
yy Pressing Centre button while checking for
the update will end the process.
yy If there is no update available, the Message,
“No update is found.” appears. Press Centre
button to return to the [Home Menu].
4. If a newer version exists, the message “Do you
want to update?” appears.
5. Select [OK] to start update. (Selecting [Cancel]
will end the update.)
>>Caution
Do not turn off the power during the software
update.
Appendix 47
6. When update is completed, the message,
“Update is complete.” will appear, and then
power will turn off automatically after 5
seconds.
7. Turn the power back on. The system now
operates with the new version.
,,Note
The Software Update function may not
work properly depending on your internet
environment. In this case, you can obtain
the latest software from the authorized LG
Electronics Service centre then update your
unit. Refer to “Customer Support” on page 45.
About Nero
MediaHome 4
Essentials
Nero MediaHome 4 Essentials is a software for
sharing video, audio and photo files stored on
your computer to this unit as a DLNA-compatiable
digital media server.
,,Note
yy The Nero MediaHome 4 Essentials CDROM is designed for PCs and should not be
inserted in this unit or in any product other
than a PC.
yy The supplied Nero MediaHome 4 Essentials
CD-ROM is a customized software edition
only for sharing files and folders to this unit.
yy The supplied Nero MediaHome 4 Essentials
software does not support following
functions: Transcoding, Remote UI, TV
control, Internet services and Apple iTunes
yy This manual explains operations with
the English version of Nero MediaHome
4 Essentials as examples. Follow the
explanation referring to the actual
operations of your language version.
Before you install Nero MediaHome 4 Essentials,
check the system requirement shown below.
yy Windows® XP (Service Pack 2 or higher), Windows
Vista® (no Service Pack required), Windows® XP
Media Centre Edition 2005 (Service Pack 2 or
higher), Windows Server® 2003
yy Windows Vista® 64-bit edition (application runs
in 32-bit mode)
yy Windows® 7 64-bit edition (application runs in
32-bit mode)
yy Hard drive space: 200 MB hard drive space for a
typical installation of Nero MediaHome standalone
yy 1.2 GHz Intel® Pentium® III or AMD
Sempron™ 2200+ processors
yy Memory: 256 MB RAM
6
Appendix
Installing Nero MediaHome 4
Essentials
48 Appendix
yy Graphics card with at least 32 MB video memory,
minimum resolution of 800 x 600 pixels, and 16bit color settings
yy Windows® Internet Explorer® 6.0 or higher
yy DirectX® 9.0c revision 30 (August 2006) or higher
yy Network environment: 100 Mb Ethernet, WLAN
Start up your computer, and insert the supplied CDROM disc into your computer’s CD-ROM drive. An
installation wizard will walk you through the quick
and uncomplicated installation process. To install
Nero MediaHome 4 Essentials, proceed as follows:
1. Close all Microsoft Windows programs and exit
any anti-virus software that may be running.
2. Insert the supplied CD-ROM disc into your
computer’s CD-ROM drive.
3. Click [Nero MediaHome 4 Essentials].
4. Click [Run] to start installation.
5. Click [Nero MediaHome 4 Essentials]. The
installation is prepared and the installation
wizard appears.
6. Click the [Next] button to display the serial
number input screen. Click [Next] to go to the
next step.
7. If you accept all conditions, click [I accept
the License Conditions] check box and click
[Next]. Installation is not possible without this
agreement.
6
8. Click [Typical] and click [Next]. The installation
process is started.
Appendix
9. If you want to take part in the anonymous
collection of data, select the check box and click
the [Next] button.
10.Click the [Exit] button to complete the
installation.
Sharing files and folders
On your computer, you must share the folder
contained video, audio and/or photo content to
play them on this unit.
This parts explains the procedure for selecting the
shared folders on your computer.
1. Double-click the “Nero MediaHome 4 Essentials”
icon on the desktop.
2. Click [Network] icon on the left and define your
network name in the [Network name] field. The
Network name you enter will be recognized by
your unit.
3. Click [Shares] icon on the left.
4. Click [Local Folders] tab on the [Shares] screen.
5. Click [Add] icon to open the [Browse Folder]
window.
6. Select the folder containing the files you want
to share. The selected folder is added to the list
of shared folders.
7. Click [Start Server] icon to start the server.
,,Note
yy If the shared folders or files are not displayed
on the unit, click the folder on the [Local
Folders] tab and click [Rescan Folder] at the
[More] button.
yy Visit www.nero.com for more information
and software tools
Appendix 49
Trademarks and
Licenses
DivX®, DivX Certified® and associated logos
are trademark of DivX, Inc., and are used under
license
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI licensing LLC.
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
Manufactured under license under U.S. Patent
Nos: 5,956,674; 5,974,380; 6,487,535 & other U.S.
and worldwide patents issued & pending. DTS,
the Symbol, & DTS and the Symbol together are
registered trademarks & DTS 2.0+Digital Out is a
trademark of DTS, Inc. Product includes software.
© DTS, Inc. All Rights Reserved.
6
The Wi-Fi CERTIFIED Logo is a certification mark
of the Wi-Fi Alliance.
Appendix
DLNA®, the DLNA Logo and DLNA CERTIFIED® are
trademarks, service marks, or certification marks
of the Digital Living Network Alliance.
50 Appendix
Audio Output Specifications
Digital Output (DIGITAL AUDIO OUT) *4
Jack/Setting Source
PCM Stereo
DTS Re-Encode*3 *5
Primary Pass-Thru
Dolby Digital
PCM 2ch
DTS
Dolby Digital
Dolby Digital Plus
PCM 2ch
DTS
Dolby Digital
DTS
PCM 2ch
DTS
DTS
Linear PCM 2ch
PCM 2ch
DTS
PCM 2ch
Linear PCM 5.1ch
PCM 2ch
DTS
PCM 2ch
Linear PCM 7.1ch
PCM 2ch
DTS
PCM 2ch
Jack/Setting
Source
HDMI OUT
PCM Stereo
DTS Re-Encode*3 *5
Dolby Digital
PCM 2ch
DTS
Dolby Digital
Dolby Digital Plus
PCM 2ch
DTS
Dolby Digital Plus
DTS
PCM 2ch
DTS
DTS
Linear PCM 2ch
PCM 2ch
DTS
Linear PCM 2ch
Linear PCM 5.1ch
PCM 2ch
DTS
Linear PCM 5.1ch
Linear PCM 7.1ch
PCM 2ch
DTS
Linear PCM 7.1ch
*1 The secondary and interactive audio may not
be included in the output bitstream if [Digital
Output] or [HDMI] option is set to [Primary PassThru]. (Except LPCM Codec: the output always
include interactive and secondary audio.)
6
Primary Pass-Thru *1 *2 *3
Appendix
*2 This unit automatically selects the HDMI audio
according to the decoding capability of the
connected HDMI device even though [HDMI]
option is set to [Primary Pass-Thru].
*3 The [Primary Pass-Thru] setting of the [HDMI]
option and [DTS Re-Encode] setting of the
[Digital Output] option cannot be set together.
If you set them together, the [HDMI] or
[Digital Output] option is set to [PCM Stereo]
automatically.
*4 On the [Digital Output] audio output, the
sampling frequency of DIGITAL AUDIO OUT is
limited to 96 kHz.
*5 If the [HDMI] or [Digital Output] option is set to
[DTS re-encode], the audio output is limited to
48 kHz and 5.1Ch.
yy If [HDMI] option is set to [Digital Output] option
is set to [Primary Pass-Thru] while playback Dolby
Digital Plus or DIGITAL AUDIO OUT is limited to
“PCM 2ch”.
yy If the HDMI OUT jack is connected to your
TV with High Speed HDMI™ Cable and Dolby
Digital Plus is outputted from HDMI OUT jack,
DIGITAL AUDIO OUT jack is limited to “PCM 2ch”
(When the HDMI and DIGITAL AUDIO OUT are
connected simultaneously).
yy The audio is outputted as PCM 48 kHz/16 bit for
MP3/WMA file.
yy You must select a digital audio output and
a maximum sampling frequency that your
Amplifier (or AV receiver) accepts using [Digital
Output], [HDMI] and [Sampling Freq.] options on
the [Setup] menu (see page 24).
yy If the audio format of the digital output does
not match the capabilities of your receiver, the
receiver will produce a strong, distorted sound
or no sound at all.
yy Multi-channel Digital Surround Sound via digital
connection can only be obtained if your receiver
is equipped with a Digital Multi-channel decoder.
Appendix
51
Specifications
General
Power Supply
Power consumption
Refer to the main label or refer to the main label on the bottom
AC adapter
DA-18B12
Dimensions (W x H x D)
Approx. 110 x 110 x 29 mm (4.3 x 4.3 x 1.1 inches)
Net Weight (Approx.)
0.28kg
Operating temperature
5 °C to 35 °C (41 °F to 95 °F)
Operating humidity
5 % to 90 %
Outputs
HDMI OUT (video/audio)
19 pin (Type A, HDMI™ Connector)
DIGITAL AUDIO OUT (OPTICAL)
3 V (p-p), Optical jack x 1
System
Signal system
Standard PAL color TV system
LAN port
Ethernet jack x 1, 10BASE-T / 100BASE-TX
Wireless LAN (internal antenna)
Integrated IEEE 802.11n (5 GHz and 2.4 GHz bands) wireless
networking access, compatible with 802.11a/b/g Wi-Fi networks.
Bus Power Supply (USB)
DC 5 V 0 500 mA
yy Design and specifications are subject to change without notice.
6
Appendix
52 Appendix
Maintenance
Handling the Unit
When shipping the unit
Please save the original shipping carton and
packing materials. If you need to ship the unit, for
maximum protection, re-pack the unit as it was
originally packed at the factory.
Keeping the exterior surfaces clean
yy Do not use volatile liquids such as insecticide
spray near the unit.
yy Wiping with strong pressure may damage the
surface.
yy Do not leave rubber or plastic products in
contact with the unit for a long period of time.
Cleaning the unit
To clean the unit, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not
use strong solvents such as alcohol, benzine, or
thinner, as these might damage the surface of the
unit.
6
Important Information
Relating to Network
Services
All information, data, documents, communications,
downloads, files, text, images, photographs,
graphics, videos, webcasts, publications, tools,
resources, software, code, programs, applets,
widgets, applications, products and other content
(“Content”) and all services and offerings (“Services”)
provided or made available by or through any
third party (each a “Service Provider”) is the sole
responsibility of the Service Provider from whom it
originated.
The availability of and access to Content and
Services furnished by the Service Provider through
the LGE Device are subject to change at any time,
without prior notice, including, but not limited to
the suspension, removal or cessation of all or any
part of the Content or Services.
Should you have any inquiry or problem related
to the Content or Services, you may refer to the
Service Provider’s website for the most up-todate information. LGE is neither responsible nor
liable for customer service related to the Content
and Services. Any question or request for service
relating to the Content or Services should be made
directly to the respective Content and Service
Providers.
Appendix
Please note that LGE is not responsible for any
Content or Services provided by the Service
Provider or any changes to, removal of, or cessation
of such Content or Services and does not warrant
or guaranty the availability of or access to such
Content or Services.
Download PDF