ENGLISH
OWNER’S MANUAL
Mini Hi-Fi System
Please read this manual carefully before operating
your set and retain it for future reference.
CM4630 (CM4630, CMS4630F)
CM4530 (CM4530, CMS4530F, CMS4530W)
CM4430 (CM4430, CMS4530F)
CM4330 (CM4330, CMS4330F)
CM4630-FE_DAUSLLK_ENG_7539.indd 1
2013-02-18
11:55:39
1
Getting Started
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral
triangle is intended to alert the
user to the presence of uninsulated
dangerous voltage within the
product’s enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing) instructions
in the literature accompanying the
product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
CM4630-FE_DAUSLLK_ENG_7539.indd 2
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance,
contact an authorized service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not
try to open the enclosure.
CAUTION concerning the Power cord
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
center. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. When installing the product,
ensure that the plug is easily accessible.
2013-02-18
11:55:41
Getting Started
This device is equipped with a portable battery or
accumulator.
yy The appliance is not intended for use by young
children or infirm persons without supervision.
yy Young Children should be supervised to
ensure that they do not play with appliance.
yy If the appliance is supplied from a cord
extension set or an electrical portable outlet
device, the cord extension set on electrical
portable outlet device must be positioned so
that it is not subject to splashing or ingress of
moisture.
1
Getting Started
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
3
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
CM4630-FE_DAUSLLK_ENG_7539.indd 3
2013-02-18
11:55:41
4
Table of Contents
Table of Contents
1
Getting Started
2
Safety Information
6
Unique Features
6Accesories
6
Playable file Requirement
6
– MP3/WMA music file requirement
7
– Compatible USB Devices
7
– USB device requirement
8
Remote Control
9
Front Panel
11 Rear Panel(CM4530)
12 Rear Panel(CM4630)
13 Rear Panel(CM4430/CM4330)
2Connecting
14
14
15
15
15
16
Connecting to speakers
– Attaching the speakers to the unit
Antenna Connection
Optional Equipment Connection
– AUX IN Connection
– USB Connection
CM4630-FE_DAUSLLK_ENG_7539.indd 4
3Operating
17
17
17
17
17
17
18
18
18
18
19
19
19
20
20
20
21
21
21
21
22
22
22
22
23
24
24
Basic Operations
– CD/USB Operations
Other Operations
– Programmed Playback
– Displaying file information
– Searching for a folder
– Turn off the sound temporarily
– Deleting an MP3/WMA file
– DEMO
– AUTO DJ playback
– Listening to the sound from your
external device
Radio Operations
– Listening to the radio
– Presetting the Radio Stations
– Deleting all the saved stations
– Improving poor FM reception
Sound adjustment
– Setting the surround mode
Setting the Clock
– Setting the alarm
– Sleep Timer Setting
– Dimmer
Advanced Operations
– Playing the iPod/iPhone
– Compatible iPod/iPhone
– Recording to USB
– To select recording bit rate and speed
2013-02-18
11:55:41
Table of Contents
5
4Troubleshooting
26Troubleshooting
1
5Appendix
27Specifications
28 Speaker specifications
29Maintenance
29 – Handling the Unit
29 – Notes on Discs
29 Trademarks and Licenses
2
3
4
5
CM4630-FE_DAUSLLK_ENG_7539.indd 5
2013-02-18
11:55:41
6
Getting Started
Unique Features
1
Playable file
Requirement
USB Direct Recording
Getting Started
Records music to your USB device.
AUTO DJ
MP3/WMA music file
requirement
Blends the end of one song into the beginning of
another for seamless playback.
MP3/WMA file compatibility with this unit is limited
as follows.
USB
yy Sampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
Listens to music from your USB device.
rate : within 32 to 320 kbps (MP3),
yy Bit
40 to 192 kbps (WMA)
Radio
yy Maximum files : Under 999
yy File extensions : “.mp3”/“.wma”
Listens to the radio.
yy CD-ROM file format : ISO 9660/JOLIET
Made for iPod/iPhone
Enjoys music from iPod/iPhone with simple
connection.
Accesories
Please check and identify the supplied accessories.
Remote Control (1)
recommend that you use Easy-CD Creator,
yy We
which creates an ISO 9660 file system.
yy You have to set the disc format option to
[Mastered] in order to make the discs compatible
with the LG players when formatting rewritable
discs. When setting the option to Live File
System, you cannot use it on LG players.
(Mastered/Live File System : Disc format system
for Windows Vista)
Batteries (2)
FM Antenna (1)
CM4630-FE_DAUSLLK_ENG_7539.indd 6
2013-02-18
11:55:42
Getting Started
7
Compatible USB Devices
yy MP3 Player : Flash type MP3 player.
Flash Drive :
yy USB
Devices that support USB2.0 or USB1.1.
1
Getting Started
USB function of this unit does not support
yy The
all USB devices.
USB device requirement
which require additional program
yy Devices
installation when you have connected it to a
computer, are not supported.
yy Do not extract the USB device while in operation.
a large capacity USB, it may take longer than
yy For
a few minute to be searched.
yy To prevent data loss, back up all data.
yy If you use a USB extension cable or USB hub, the
USB device is not recognized.
NTFS file system is not supported.
yy Using
(Only FAT(16/32) file system is supported.)
unit is not supported when the total
yy This
number of files is 1 000 or more.
yy E xternal HDD, Card readers, Locked devices, or
hard type USB devices are not supported.
yy USB port of the unit cannot be connected to PC.
The unit cannot be used as a storage device.
CM4630-FE_DAUSLLK_ENG_7539.indd 7
2013-02-18
11:55:42
8
Getting Started
Remote Control
1
Getting Started
• • • • • • a • • • • • • C/V (Skip/Search) :
1 (Power) : Switches the unit ON
or OFF.
-- Skips Fast backward or Forward.
B (Open/Close) : Opens and
closes the disc tray.
PRESET.FOLDER W/S :
TUNING-/+ : Selects the radio
station.
-- Searches for a folder of MP3/
WMA files. When a CD/USB
containing MP3/WMA files in
several folders is being played,
press PRESET.FOLDER W/S
to select the folder you want to
play.
Z ENTER :
-- Chooses a preset number for a
radio station.
-- Starts or pauses playback.
FUNCTION : Selects the function
and input source.
MUTE@ : Mutes the sound.
VOL +/- : Adjusts speaker volume.
• • • • • • b • • • • • • Battery Installation
-- Searches for a section within a
track/file.
-- Stops playback or recording.
-- Cancels DELETE function.
-- Chooses an item on IPOD
mode.
d/M (Play/Pause) :
-- Selects STEREO/MONO.
SOUND EFFECT : Chooses sound
impressions.
AUTO DJ : Selects the AUTO DJ
mode. (For more information refer
to the page 18)
PROGRAM/MEMORY :
- Stores radio stations.
DELETE : Deletes MP3/WMA files.
- Creates a playlist you want to
listen to.
USB REC : USB direct recording.
0 to 9 numerical buttons : Selects
numbered tracks/files, or preset
number.
? : The button is not available for
any function.
INFO : Sees informations about
your music.
REPEAT(MENU) :
- L istens to your tracks/files
repeatedly or randomly.
SLEEP : Sets the system to turn off
automatically at a specified time.
(Dimmer : The display window will
be darkened by half.)
- Moves to the previous menu on
IPOD mode.
• • • • • • c • • • • • • • • • • • • d • • • • • • ? : The button is not available for
any function.
Remove the battery cover on the
rear of the Remote Control, and
insert two (size AAA) batteries
with 4 and 5 matched correctly
CM4630-FE_DAUSLLK_ENG_7539.indd 8
2013-02-18
11:55:43
Getting Started
9
Front Panel
1
Getting Started
CM4630-FE_DAUSLLK_ENG_7539.indd 9
2013-02-18
11:55:43
10
Getting Started
aDisc tray
Reads a disc.
1
bAUTO DJ
Selects the AUTO DJ mode.
(For more informaion refer to the page 18)
jUSB
- Plays the audio files by connecting the USB
device.
- Connects iPod/iPhone by using iPod/iPhone
cable.
Getting Started
USB REC.
Records music to USB.
cTIMER
Uses your unit as an alarm clock.
dY (Skip/Search)
- Searches forward.
- Skips to the previous track/file.
kFUNC.
Selects the function or input source.
eBASS BLAST
Reinforces the treble, bass and surround effect.
lDEMO
Demonstrates each of functions.
fI(Stop)
Stops playback or recording.
mTST./MO.
- Starts or pauses playback.
- Selects Stereo/Mono.
gSET
Confirms the setting.
nVolume knob
Adjusts volume of speaker.
h1/! (Power)
Switches the unit ON or OFF.
oLG EQ
Chooses sound impressions.
iDisplay window
pU (Skip/Search)
- Searches backward.
- Skips to the next track/file.
qCLOCK
Sets the clock and checks the time.
rR (Open/Close)
Opens and closes the disc tray.
CM4630-FE_DAUSLLK_ENG_7539.indd 10
2013-02-18
11:55:43
Getting Started
11
Rear Panel(CM4530)
1
Getting Started
a AUX IN (L/R) connectors
d Cooling fan
b ANTENNA (FM)
eSPEAKERS terminal/cord
c POWER IN
CM4630-FE_DAUSLLK_ENG_7539.indd 11
2013-02-18
11:55:43
12
Getting Started
Rear Panel(CM4630)
1
Getting Started
a AUX IN (L/R) connectors
d Cooling fan
b ANTENNA (FM)
eSPEAKERS terminal
c POWER IN
CM4630-FE_DAUSLLK_ENG_7539.indd 12
2013-02-18
11:55:44
Getting Started
13
Rear Panel(CM4430/CM4330)
1
Getting Started
a AUX IN (L/R) connectors
c POWER IN
b ANTENNA (FM)
d SPEAKERS terminal
CM4630-FE_DAUSLLK_ENG_7539.indd 13
2013-02-18
11:55:44
14
Connecting
Connecting to
speakers
Attaching the speakers to the
unit
2
Connecting
To connect the cable to the unit, press each plastic
finger pad to open the connection terminals on the
unit. Insert the wire and release the finger pad.
Connect the black stripe of each wire to the
terminals marked - (minus) and the other end to
the terminals marked + (plus).
>>Caution
yy Be careful to make sure children do not put
their hands or any objects into the *speaker
duct.
*Speaker duct: A hall for plentiful bass
sound on speaker cabinet (enclosure)
yy The speakers contain magnet parts, so
colour irregularity may occur on the TV
screen or PC monitor screen. Please use the
speakers far away from either TV screen or
PC monitor.
yy Do not connect any other speaker except
sub woofer speaker to the sub woofer
connection terminal on the rear of the unit.
CM4530
colour
Speaker
Orange
Sub woofer
Red
Front
White
Front
CM4630/CM4430/CM4330
Connect a woofer cord to the player.
When connecting a woofer cord to the player,
insert the connector until it clicks.
CM4630-FE_DAUSLLK_ENG_7539.indd 14
colour
Speaker
Red
Front
White
Front
2013-02-18
11:55:45
Connecting
Antenna Connection
Connect the supplied FM antenna for listening to
the radio.
Connect the FM wire antenna to the FM antenna
connector.
15
Optional Equipment
Connection
AUX IN Connection
Connect an output of auxiliary device(Camcoder,
TV, Player, etc) to the AUX IN(L/R) connector.
,,Note
Be sure to fully extend the FM wire antenna.
CM4630-FE_DAUSLLK_ENG_7539.indd 15
2
Connecting
If your device has only one output for audio(mono),
connect it to the left (white) audio jack on the unit.
Red
White
To the audio output jacks
of your component
(TV, VCR, etc.)
2013-02-18
11:55:46
16
Connecting
USB Connection
Connect the USB port of USB Memory (or MP3
player, etc.) to the USB port on the front of the unit.
2
Connecting
,,Note
Removing the USB Device from the unit.
1. Choose a different function/mode or
press I(Stop) twice in a row.
2. Remove the USB device from the unit.
CM4630-FE_DAUSLLK_ENG_7539.indd 16
2013-02-18
11:55:47
Operating
17
Basic Operations
Other Operations
CD/USB Operations
Programmed Playback
1. Insert the disc by pressing B on the remote
control or R on the unit.
Connect the USB device to the USB port.
The program function enables you to store your
favourite files from any disc or USB device.
2. Select the CD or USB function by pressing
FUNCTION on the remote control or FUNC. on
the unit.
1. Insert a CD or connect your USB and wait for it
to be ordered.
3. Select a track/file you want to play by pressing
C/V on the remote control or Y/U
on the unit.
Do this
Press Z ENTER or I.
Press d/M or TST./MO..
During playback, Press d/M or
Pause
TST./MO..
During playback, press C/
V or Y/U to go to the
next track/file or to return to the
Skipping to beginning of the current track/file.
the next/ Playing less than 2 seconds, press
previous C or Y to go to the previous
track/file track/file.
Playing after 3 seconds, press C
or Y to go to the beginning of
the track/file.
Selecting
a track/file
directly
Press 0 to 9 numerical buttons
to go to the desired file or track
directly.
Searching
Press and hold C/V or Y/
for a section
U during playback and release it
within
at the point you want to listen to.
a track/file
Press REPEAT(MENU) repeatedly.
The display will be changed in the
Playing
following order.
repeatedly or
RPT1 -> RPT *DIR (only MP3/WMA)
randomly
-> RPT ALL -> RANDOM -> OFF.
*DIR : Directory
CM4630-FE_DAUSLLK_ENG_7539.indd 17
2.Press PROGRAM/MEMORY on the remote
control in stop status.
3.Press C/V on the remote control to select
a track/file.
4.Press PROGRAM/MEMORY again to save and
select a next track/file.
5. Repeat steps 3-4 to select a next track/file.
6.Press d/M to play the programmed music
tracks/files.
3
Operating
To
Stop
Playback
A program can contain 20 tracks/files.
7. To clear your selection, press Z ENTER twice.
,,Note
The programs are also cleared when the disc
or USB device is removed, the unit is powered
off or the function is switched to others.
Displaying file information
While playing an MP3 file containing file
information, you can display the information by
pressing INFO.
Searching for a folder
1.Press PRESET·FOLDER W/S on the remote
control repeatedly until a desired folder appears
in the display window.
2.Press d/M to play it. The first file of the folder
will be played.
2013-02-18
11:55:47
18
Operating
Turn off the sound temporarily
AUTO DJ playback
Press MUTE@ on the remote control to mute
your sound.
Auto DJ blends the end of one song into the
beginning of another for seamless playback. It
equalizes volume across tracks for uninterrupted
playback.
You can mute your sound, for example, to answer
the telephone, the “MUTE” will appear and blink in
the display window.
To cancel it, press MUTE @ again or change the
volume level.
Deleting an MP3/WMA file
You can delete a file, folder or format by pressing
DELETE. (USB only)
3
Operating
1.Press DELETE repeatedly while selecting the
MP3/WMA file. This function is supported
only in stop status. The display changes in the
following order.
- DEL FILE : Deletes file.
- DEL DIR : Deletes folder.
- FORMAT : Formats USB.
2. To delete file/folder or format, press d/M
on the remote control or press T ST./MO. on
the unit.
3. If you want to exit the current mode,
press Z ENTER on the remote control or
press I on the unit.
>>Caution
yy Do not extract the USB device during
operation.(play, delete, etc.)
yy Regular back up is recommended to
prevent data loss.
yy The delete function may not be supported
according to the USB status.
DEMO
In power off state, press DEMO on the unit once.
The unit will power on and display the each of
functions in the display window. To cancel the
DEMO function, press DEMO once more.
,,Note
Press AUTO DJ on the remote control or unit
repeatedly, the display changes as followings.
RANDOM (AUTO DJ RANDOM) -> RPT (AUTO DJ
SEQUENTIAL) -> (AUTO DJ OFF)
Mode
OFF
Display
Window
(AUTO DJ OFF)
Description
-
RANDOM
RANDOM
(AUTO DJ
RANDOM)
The music is
played randomly
on this mode.
REPEAT
RPT
(AUTO DJ
SEQUENTIAL)
The music is
played repeatedly
on this mode.
,,Note
yy S earching for a section within a track/file
or playing repeatedly or randomly is not
supported on the AUTO DJ mode.
yy During AUTO DJ mode, it is not available to
search file by pressing PRESET.FOLDER
W/Son the remote control.
yy If you move to other functions or stop the
music using I on the unit (or Z ENTER on
the remote control) on AUTO DJ mode,
AUTO DJ function will be disable.
UTO DJ function is not supported in the
yy A
music file whose length is less than 60
seconds.
uring recording, AUTO DJ function is not
yy D
available.
yy If you change a disc while the AUTO DJ
function is activated, the function is
deactivated.
You can enjoy other functions during the
DEMO. Then the DEMO will pause temporarily.
- Without input key in 10 sec, the DEMO
will play back automatically.
CM4630-FE_DAUSLLK_ENG_7539.indd 18
2013-02-18
11:55:47
Operating
Listening to the sound from
your external device
Radio Operations
The unit can be used to play the sound from many
types of external device. (Refer to the page 15)
Be sure that FM aerial is connected.
(Refer to the page 15)
1. Connect the external device to the AUX IN(L/R)
connector of the unit.
Listening to the radio
2. Turn the power on by pressing 1/!(Power).
1.Press FUNCTION on the remote control or
FUNC. on the unit until FM appears in the
display window.
The last received station is tuned in.
3. Select the AUX function by pressing FUNC. on
the unit.
4. Turn the external device and start playing it
19
2. Auto tuning : Press TUNING -/+ on the remote
control or Y/U on the unit for about 2
seconds until the frequency indication starts
changing, then release. scanning stops when
the unit tunes in a station.
Manual tuning: Press TUNING -/+ on the
remote control or Y/U on the unit
repeatedly.
3. Adjust the volume by pressing VOL +/- on the
remote control or by rotating volume knob on
the unit repeatedly.
CM4630-FE_DAUSLLK_ENG_7539.indd 19
2013-02-18
3
Operating
11:55:47
20 Operating
Presetting the Radio Stations
You can preset 50 stations for FM.
Before tuning, make sure to turn down the volume.
1.Press FUNCTION on the remote control or
FUNC. on the unit until FM appears in the
display window.
2. Select the desired frequency by pressing
TUNING-/+ on the remote control or
Y/U on the unit.
3.Press PROGRAM/MEMORY. A preset number
will blink in the display window.
4.Press PRESET·FOLDER W/S to select the
preset number you want.
3
5.Press PROGRAM/MEMORY. The station is
stored.
Operating
6. Repeat steps 2 to 5 to store other stations.
7. To listen to a preset station, press
PRESET·FOLDER W/S or 0 to 9 numerical
buttons.
Deleting all the saved stations
1. Press and hold PROGRAM/MEMORY for two
seconds. “ERASEALL” will blink in the unit display.
2.Press PROGRAM/MEMORY to erase all saved
radio stations.
Improving poor FM reception
Press d/M on the remote control or T ST./MO.
on the unit. This will change the tuner from stereo
to mono. Then the reception will be better than
before.
CM4630-FE_DAUSLLK_ENG_7539.indd 20
2013-02-18
11:55:47
Operating
Sound adjustment
Setting the Clock
Setting the surround mode
1. Turn the unit on.
This system has a number of pre-set surround
sound fields. You can select a desired sound mode
by using SOUND EFFECT on the remote control or
LG EQ on the unit.
The displayed items for the Equalizer may be
different depending on sound sources and effects.
Description
NATURAL
You can enjoy comfortable and
natural sound.
AUTO EQ
Realizes the sound equalizer that
is the most similar to the genre
of which is included in the MP3
ID3 tag of song files.
POP
CLASSIC
JAZZ
ROCK
This program lends an
enthusiastic atmosphere to the
sound, giving you the feeling
you are at an actual rock pop,
jazz or classic concert.
MP3 -- OPT
This function is optimized
for compressible MP3 file. It
improves the treble sound.
BASS
Reinforces the treble, bass and
surround sound effect.
LOUDNESS
Improves the bass and treble
sound.
BYPASS
You can enjoy the sound
without equalizer effect.
,,Note
n some speakers, sound may not be heard
yy O
or heard in low sound depending on the
sound mode.
aybe you need to reset the surround
yy M
mode, after switching the input, sometimes
even after the sound track changed.
2.Press CLOCK.
3. Choose time mode by pressing Y/U.
- AM 12:00 (for an AM and PM display)
or 0:00 (for a 24 hour display)
4.Press SET to confirm your selection.
5. Select the hours by pressing Y/U.
6.Press SET.
7. Select the minutes by pressing Y/U.
8.Press SET.
9. If you want to reset the clock, press and hlod
CLOCK. Then repeat steps 3-8.
Setting the alarm
You can use the unit as an alarm clock.
You have to set the clock before setting the alarm.
3
Operating
On Display
21
1. Turn the unit on.
2.Press TIMER.
3. Each of functions will blink. Press SET to select a
sound source you want.
4. “ON TIME” will be displayed. This is your desired
time to the unit turns on. Press Y/U to
change the hours and minutes and press
SET to save.
5. The “OFF TIME” will be displayed. This is your
desired time to the unit turns off. Press Y/U
to change the hours and minutes and press SET
to save.
6.Press Y/U to change the volume and
press SET to save. The clock icon "(“ shows
that the alarm is set.
7.Press TIMER. You can check the setting status.
8. If you want to reset the alarm, press and hlod
TIMER. Then repeat steps 3-6.
yy By pressing BASS BLAST on the unit you
can directly select the BYPASS or BASS
BLAST sound.
CM4630-FE_DAUSLLK_ENG_7539.indd 21
2013-02-18
11:55:47
22 Operating
Sleep Timer Setting
Press SLEEP on the remote control repeatedly to
select delay time between 10 and 180 minutes.
After delay time, the unit will turn off. (You can see
the following order, 180 ->150 -> 120 -> 90 -> 80
-> 70 -> 60 -> 50 -> 40 -> 30 -> 20 -> 10). To cancel
the sleep function, press SLEEP repeatedly until the
display window get bright.
,,Note
•• Press SLEEP. The remaining time appears in
the display window.
Advanced Operations
Playing the iPod/iPhone
You can enjoy the sound with your iPod/iPhone.
For details about iPod/iPhone, refer to the iPod/
iPhone User Guide.
1. Connect iPod/iPhone to the USB port on the
front of the unit by using the iPod/iPhone cable.
•• If Sleep function is set the front display will
dim.
3
Operating
Dimmer
Press SLEEP once. The display window will
be darkened by half. To cancel it, press SLEEP
repeatedly until the display window get bright.
,,Note
•• After setting a clock function, you can set
alarm function.
•• If you set the clock and alarm, you can check
the time and alarm icon “(“ by pressing
CLOCK although the unit is turned off.
•• During playback, press TIMER two times
when the alarm icon “(“ is displayed. You
can check the setting state.
•• If you activate the alarm, the alarm icon “(“
will appear in the display window.
•• If you deactivate the alarm, the alarm icon
“(“ will disappear in the display window.
2. Press FUNCTION on the remote control or
FUNC. on the unit to select USB function. You
can operate your iPod/iPhone through an iPod/
iPhone’s display by using the remote control
and controlling your iPod/iPhone.
•• Alarm function only works when the unit is
turned off.
•• If the time you set is up, the unit will be
turned on automatically.
If you turn this unit on, your iPod/iPhone will be
automatically turned on and start recharging.
•• Alarm function is not supported even if
you choose USB function as an alarm clock
when iPod/iPhone is connected to USB
port.
CM4630-FE_DAUSLLK_ENG_7539.indd 22
2013-02-18
11:55:47
Operating 23
To
Do this
ON UNIT
ON REMOTE
Pause or
restart
T
ST./MO.
d/M
Skip
Y/U
C/V
Search
Press and hold
Y/U
Press and hold
C/V
-
REPEAT
(MENU)
Move to the
Previous
menu
-
PRESET·
FOLDER
W/S
Choose an
item
I
Z ENTER
Compatible iPod/iPhone
The unit supports the models as follows.
yy iPod touch
yy iPod classic
yy iPod nano
yy iPhone 5
- Your iPod/iPhone is not connected firmly.
- This unit recognizes your iPod/iPhone as
an unknown device.
- Your iPod/iPhone is exceptionally low in
power.
/ The battery needs to be charged.
/If you charge the battery while iPod/
iPhone is extremely low in power,
it may take longer to be charged.
yy Depending on your iPod/iPhone’s software
version, it may not be possible to control
your iPod/iPhone from this unit. We
recommend installing the latest software
version.
yy If you use an application, make a call, or
send and receive SMS text message, etc. on
iPod touch or iPhone, disconnect it from
this unit and then use it.
3
Operating
Move to the
desired item
,,Note
yy If this unit displays an error message “NO
USB” follow check procedure below.
yy If you have a problem with your iPod/
iPhone, please visit www.apple.com/
support.
yy You may need additional operation for iPod
touch or iPhone, for example “unlock” by
draging the slider.
yy iPhone 4S
yy iPhone 4
yy iPhone 3GS
yy iPhone 3G
Depending on your iPod/iPhone’s software version,
you may not control your iPod/iPhone from the
unit.
Depending on your iPod/iPhone device, you may
not control your iPod/iPhone from the unit.
CM4630-FE_DAUSLLK_ENG_7539.indd 23
2013-02-18
11:55:48
24 Operating
Recording to USB
You can record various sound sources to USB.
1. Connect the USB device to the unit.
2. Select a function by pressing FUNCTION on the
remote control or FUNC. on the unit.
To select recording bit rate
and speed
1.Press USB REC on the remote control or
USB REC. on the unit for longer than 3
seconds.
One track/file recording - You can record to USB
after playing a track/file you want.
2.Use C/V on the remote control or Y/
U on the unit to select the bit rate.
All tracks/files recording - You can record to USB
after stop.
3.Press USB REC on the remote control or
USB REC. on the unit again to select the
recording speed.
Program list recording - After showing the
programmed list, you can record it to USB.
(Refer to the page 17)
4.Press C/V on the remote control or
Y/U on the unit to select a desired
recording speed : (AUDIO CD only)
3
3. Start the recording by pressing USB REC on the
remote control or
USB REC. on the unit.
X1 SPEED
- You can listen to music while recording it.
Operating
4. To stop recording, press Z ENTER on the
remote control or I on the unit.
X2 SPEED
- You can just record the music file.
Pausing recording
During recording, press USB REC on the remote
control or
USB REC. on the unit to pause
recording. Press it again to restart recording.
(Only Radio/AUX)
CM4630-FE_DAUSLLK_ENG_7539.indd 24
5.Press USB REC on the remote control or
USB REC. on the unit to finish the setting.
2013-02-18
11:55:48
Operating 25
,,Note
yy You can check the recording percentage
rate for the USB record on the display
window during the recording.
(MP3/WMA CD Only)
yy During recording MP3/WMA, there is no
sound.
yy When you stop recording during playback,
the file that has been recorded at that time
will be stored. (Except MP3/WMA files)
yy Do not remove the USB device or turn
off the unit during USB recording. If not,
an incomplete file may be made and not
deleted on PC.
yy If USB recording does not work, the
message like “NO USB”, “ERROR”, “FULL” or “NO
REC” is displayed on the display window.
3
Operating
yy Multi card reader device or External HDD
can not be used for USB recording.
yy A file is recorded by about 512 Mbyte when
you record for a long term.
yy You may not store more than 999 files.
yy It’ll be stored as follows.
AUDIO CD
MP3/WMA
The other
source*
* : TUNER, AUX and the like.
The making of unauthorized copies of copyprotected material, including computer
programs, files, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal offense.
This equipment should not be used for such
purposes.
Be responsible
Respect copyrights
CM4630-FE_DAUSLLK_ENG_7539.indd 25
2013-02-18
11:55:48
26 Troubleshooting
Troubleshooting
Problem
Cause & Correction
yy The power cord is not plugged in. Plug in the power cord.
No Power.
No sound.
yy Check whether electricity failed.Check the condition by operating other
electronic devices.
yy Check whether you select a right function. Press FUNC. and check the
selected function.
yy Speaker cables are not connected correctly. Connect speaker cables correctly.
yy An unplayable disc is inserted. Insert a playable disc.
The unit does not start
playback.
4
yy No disc is inserted. Insert a disc.
yy The disc is dirty. Clean the disc. (Refer to the 29 page)
yy The disc is inserted upside down. Place the disc with the label or printed side
facing upwards.
Troubleshooting
yy The antenna is positioned or connected poorly. Connect the antenna securely.
yy The signal strength of the radio station is too weak. Tune to the station
manually.
Radio stations cannot be
tuned in properly.
yy No stations have been preset or preset stations have been cleared (when
being tuned by scanning preset channels). Preset some radio stations, see
page 20 for details.
yy The remote control is too far from the unit. Operate the remote control within
about 23 ft (7 m).
The remote control does yy There is an obstacle in the path of the remote control and the unit. Remove
the obstacle.
not work properly.
yy The batteries in the remote control are exhausted. Replace the batteries with
new ones.
iPod/iPhone does not
work.
yy Check whether the player is connected to the unit correctly. Connect it to the
unit correctly.
CM4630-FE_DAUSLLK_ENG_7539.indd 26
2013-02-18
11:55:48
Appendix 27
Specifications
General
Model
CM4630
Power requirements
Refer to the main label.
CM4530
Power consumption
Refer to the main label.
Dimensions (W x H x D)
202 x 307 x 315 mm
Net Weight (Approx.)
3.15 kg
Operating temperature
5 °C to 35 °C (41 °F to 95 °F)
Operating humidity
5 % to 90 %
Bus Power Supply
DC 5 V 0 1 A
CM4430
CM4330
Inputs
AUX IN
2.0 Vrms (1 kHz, 0 dB), 75 Ω, RCA jack (L, R) x 1
Tuner
FM Tuning Range
87.5 to 108.0 MHz or 87.50 to 108.00 MHz
Amplifier
5
CM4630
CM4530
CM4430
CM4330
Stereo mode
250 W + 250 W
(3 Ω at 1 KHz,
THD 10 %)
160 W + 160 W
(4 Ω at 1 KHz,
THD 10 %)
150 W + 150 W
(4 Ω at 1 KHz,
THD 10 %)
90 W + 90 W
(4 Ω at 1 KHz,
THD 10 %)
250 W + 250 W
(3 Ω at 1 KHz,
THD 10 %)
160 W + 160 W
(4 Ω at 1 KHz,
THD 10 %)
150 W + 150 W
(4 Ω at 1 KHz,
THD 10 %)
90 W + 90 W
(4 Ω at 1 KHz,
THD 10 %)
Front
Surround
mode
Subwoofer
-
180 W
(3 Ω at 1 KHz,
THD 10 %)
-
Appendix
Model
-
CD
Frequency Response
100 to 20 000 Hz
Signal-to-noise ratio
75 dB
Dynamic range
80 dB
CM4630-FE_DAUSLLK_ENG_7539.indd 27
2013-02-18
11:55:48
28 Appendix
Speaker specifications
Front speaker
CMS4530F
(CM4530)
CMS4530F
(CM4430)
CMS4330F
160 W
150 W
90 W
320 W
300 W
180 W
Net Dimensions (W x H x D)
245 x 452 x 275
mm
232 x 352 x 262
mm
232 x 352 x 262
mm
204 x 301 x 235
mm
Net Weight
5.55 kg
3.32 Kg
3.32 Kg
2.48 Kg
Model
CMS4630F
Type
2 Way 2 Speaker
Impedance
3Ω
4Ω
Rated Input Power
250 W
Max. Input power
500 W
Subwoofer speaker
5
Model
CMS4530W
Type
1 Way 1 Speaker
Impedance
3Ω
Rated Input Power
180 W
Max. Input power
360 W
Net Dimensions (W x H x D)
250 x 352 x 327 mm
Net Weight
5.58 kg
Appendix
yy Design and specifications are subject to change without notice.
CM4630-FE_DAUSLLK_ENG_7539.indd 28
2013-02-18
11:55:48
Appendix 29
Maintenance
Handling the Unit
Notes on Discs
Handling Discs
Never stick paper or tape on the disc.
When shipping the unit
Storing Discs
Please save the original shipping carton and
packing materials. If you need to ship the unit, for
maximum protection, re-pack the unit as it was
originally packed at the factory.
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of heat
and never leave it in a parked car exposed to direct
sunlight.
Keeping the exterior surfaces clean
Cleaning Discs
Do not use volatile liquids such as insecticide spray
near the unit.
Do not use strong solvents such as alcohol,
benzine, thinner, commercially available cleaners,
or anti-static spray intended for old vinyl records.
Wiping with strong pressure may damage the
surface.
Do not leave rubber or plastic products in contact
with the unit for a long period of time.
Cleaning the unit
Trademarks and
Licenses
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not
use strong solvents such as alcohol, benzine, or
thinner, as these might damage the surface of the
unit.
The unit is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty
or worn, the picture quality could be diminished.
For details, please contact your nearest authorized
service center.
CM4630-FE_DAUSLLK_ENG_7539.indd 29
“Made for iPod,” and “Made for iPhone” mean
that an electronic accessory has been designed
to connect specifically to iPod or iPhone,
respectively, and has been certified by the
developer to meet Apple performance standards.
Apple is not responsible for the operation of
this device or its compliance with safety and
regulatory standards. Please note that the use
of this accessory with iPod or iPhone may affect
wireless performance.
2013-02-18
Appendix
Maintaining the Unit
5
11:55:49
CM4630-FE_DAUSLLK_ENG_7539.indd 30
2013-02-18
11:55:49
Download PDF

advertising