LG | CM4320 | LG CM4320 Owner’s Manual

OWNER’S MANUAL
Mini Hi-Fi System
Please read this manual carefully before operating
your set and retain it for future reference.
CM4620 (CM4620, CMS4620F),
CM4520 (CM4520, CMS4520F, CMS4520W)
CM4420 (CM4420, CMS4520F), CM4320 (CM4320, CMS4320F)
1
Getting Started
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing) instructions
in the literature accompanying the
product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance,
contact an authorized service centre.
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not
try to open the enclosure.
CAUTION concerning the Power cord
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
center. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. When installing the product,
ensure that the plug is easily accessible.
Getting Started
3
This device is equipped with a portable battery or
accumulator.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
1
You have to set the disc format option to [Mastered]
in order to make the discs compatible with the LG
players when formatting rewritable discs. When
setting the option to Live File System, you cannot
use it on LG players.
(Mastered/Live File System : Disc format system for
Windows Vista)
Getting Started
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
4
Table of Contents
Table of Contents
1
Getting Started
2
Safety Information
6
Unique Features
6Accesories
6
Playable file Requirement
6
– MP3/WMA music file requirement
6
– Compatible USB Devices
6
– USB device requirement
7
Remote control
8
Front panel
10 Rear panel
2Connecting
11
11
11
11
12
12
Connecting to speakers
– Attaching the speakers to the unit
Optional Equipment Connection
– AUX IN Connection
– USB Connection
– Antenna Connection
3Operating
13
13
13
13
14
14
14
14
15
15
16
16
16
16
16
17
17
18
18
19
19
20
20
20
21
Basic Operations
– CD/USB Operations
Other Operations
– Programmed Playback
– Displaying file information (ID3 TAG)
– Searching for a folder
– Turn off the sound temporarily
– Deleting an MP3/WMA file
– DEMO
– AUTO DJ playback
Radio Operations
– Listening to the radio
– Presetting the Radio Stations
– Deleting all the saved stations
– Improving poor FM reception
Sound adjustment
– Setting the surround mode
Setting the Clock
– Setting the alarm
– Sleep Timer Setting
– Dimmer
Advanced Operations
– Playing the iPod/iPhone
– Compatible iPod/iPhone
– Listening to the sound from your
external device
21 – Recording to USB
22 – To select recording bit rate and speed
Table of Contents
5
4Troubleshooting
23Troubleshooting
5Appendix
24 Trademarks and Licenses
25Specifications
27Maintenance
27 – Notes on Discs
27 – Handling the Unit
1
2
3
4
5
6
Getting Started
Unique Features
1
USB Direct Recording
Compatible USB Devices
yy MP3 Player : Flash type MP3 player.
yy USB Flash Drive :
Devices that support USB2.0 or USB1.1.
Getting Started
Records music to your USB device.
yy The USB function of this unit does not support
all USB devices.
Accesories
USB device requirement
Please check and identify the supplied accessories.
yy Devices which require additional program
installation when you have connected it to a
computer, are not supported.
yy Do not extract the USB device while in operation.
yy For a large capacity USB, it may take longer than
a few minute to be searched.
Remote Control (1)
Batteries (2)
yy To prevent data loss, back up all data.
yy If you use a USB extension cable or USB hub, the
USB device is not recognized.
yy Using NTFS file system is not supported.
(Only FAT(16/32) file system is supported.)
FM Antenna (1)
AM Antenna (1)
Playable file
Requirement
MP3/WMA music file
requirement
MP3/WMA file compatibility with this unit is limited
as follows :
yy Sampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
yy Bit rate : within 32 to 320 kbps (MP3),
40 to 192 kbps (WMA)
yy Maximum files : Under 999
yy File extensions : “.mp3”/“.wma”
yy CD-ROM file format : ISO9660/JOLIET
yy We recommend that you use Easy-CD Creator,
which creates an ISO 9660 file system.
yy This unit is not supported when the total
number of files is 1 000 or more.
yy External HDD, Card readers, Locked devices, or
hard type USB devices are not supported.
yy USB port of the unit cannot be connected to PC.
The unit cannot be used as a storage device.
Getting Started
7
Remote control
• • • • • • a • • • • • • B (OPEN/CLOSE) : Opens and
closes the disc tray.
PRESET.FOLDER W/S :
-- Searches for a folder of MP3/
WMA files. When a CD/USB
containing MP3/WMA files in
several folders is being played,
press PRESET.FOLDER W/S
to select the folder you want to
play.
-- Chooses a preset number for a
radio station.
FUNCTION : Selects the function
and input source.
-- Skips Fast backward or Forward.
-- Searches for a section within a
track/file.
Z ENTER :
-- Stops playback or recording.
-- Cancels DELETE function.
-- Chooses an item on IPOD mode.
d/M (Play/Pause) :
-- Starts or pauses playback.
-- Selects STEREO/MONO.
SOUND EFFECT : Chooses sound
impressions.
VOL +/- : Adjusts speaker volume.
• • • • • • b • • • • • • DELETE : Deletes MP3/WMA files.
PROGRAM/MEMORY :
• • • • • • c • • • • • • -- For storing radio stations if you
have saved radio stations by
using PROGRAM/MEMORY,
you can scroll through them and
select one.
0 to 9 numerical buttons : Selects
numbered tracks/files, or preset
number.
-- Listens to your tracks/files in any
order.
USB REC : USB direct recording.
: The button is not available for
any function.
REPEAT(MENU) :
-- Listens to your tracks/files
repeatedly or randomly.
Remove the battery cover on the
rear of the Remote Control, and
insert two (size AAA) battery with
4 and 5 matched correctly
C/V (Skip/Search) :
AUTO DJ : Selects the AUTO DJ
mode. (For more information refer
to the page 15)
MUTE@ : Mutes the sound.
Battery Installation
TUNING-/+ : Selects the radio
station.
-- Moves to the previous menu on
IPOD mode.
INFO : Sees informations about
your music. An MP3 file often
come with ID3 tag. The tag gives
the Title, Artist, Album or Time
information.
SLEEP : Sets the system to turn off
automatically at a specified time.
(Dimmer : The display window will
be darkened by half.)
• • • • • • d • • • • • • : The button is not available for
any function.
1
Getting Started
1 (POWER) : Switches the unit
ON or OFF.
8
Getting Started
Front panel
1
Getting Started
Getting Started
a Display window
k
bUSB
You can play or record music files by
connecting the USB device.
l CLOCK
For setting the clock and checking the time.
c 1/! (Power)
d TIMER
With the TIMER function you can turn CD, USB
play and TUNER reception on or off at a desired
time.
eI
Stops playback or recording.
USB REC
Records to USB.
mSET/DEMO
Confirms the setting.
Shows demo.
nT ST./MO.
Starts playback and pauses.
Selects Stereo/Mono.
o FUNC.
Selects the function or input source.
p U (Skip/Search)
f BASS BLAST
Reinforces the treble, bass and surround effect.
qBacklightings
g Y (Skip/Search)
s Disc tray
h AUTO DJ
Selects the AUTO DJ mode.
(For more information refer to the page 15)
i LG EQ
Chooses sound impressions.
j VOLUME
r R (OPEN/CLOSE)
1
Getting Started
connects iPod/iPhone by using iPod/iPhone
cable.
9
10
Getting Started
Rear panel
1
Getting Started
a Power cord
b ANTENNA (FM/AM)
c AUX IN (L/R) connectors
d Speaker terminals
CM4520B Speaker terminal
Connecting
Connecting to
speakers
Optional Equipment
Connection
Attaching the speakers to the
unit
AUX IN Connection
Connect the black stripe of each wire to the
terminals marked - (minus) and the other end to
the terminals marked + (plus).
>>Caution
yy Be careful to make sure children not to put
their hands or any objects into the *speaker
duct.
*Speaker duct: A hole for plentiful bass
sound on speaker cabinet (enclosure).
yy The speakers contain magnet parts, so color
irregularity may occur on the TV screen or
PC monitor screen. Please use the speakers
far away from either TV screen or PC
monitor.
yy Make sure to install the speaker with other
people in order to prevent it from falling
and causing injuries to the installer.
Connect an output of auxiliary device(Camcoder,
TV, Player, etc) to the AUX IN (L/R) connector.
If your device has only one output for audio(mono),
connect it to the left (white) audio jack on the unit.
2
Connecting
To connect the cable to the unit, press each plastic
finger pad to open the connection terminals on the
unit. Insert the wire and release the finger pad.
11
12
Connecting
USB Connection
Antenna Connection
Connect the USB port of USB Memory (or MP3
player, etc.) to the USB port on the front of the unit.
Connect the supplied FM/AM antenna for listening
to the radio.
Connect the FM wire antenna to the FM antenna
connector.
Connect the AM loop antenna to the AM antenna
connector.
2
Connecting
,,Note
Removing the USB Device from the unit.
1. Choose a different function/mode or
press Z ENTER twice in a row.
2. Remove the USB device from the unit.
,,Note
yy Be sure to fully extend the FM wire antenna.
After connecting the FM wire antenna, keep
it horizontal.
yy To prevent noise pickup, keep the AM Loop
antenna away from the unit and other
components.
3Operating
Operating
Basic Operations
Other Operations
CD/USB Operations
Programmed Playback
1. Insert the disc by pressing B(OPEN/CLOSE) or
connect the USB device to the USB port.
The program function enables you to store your
favorite files from any disc or USB device.
2. Select the CD or USB function by pressing
FUNCTION on the remote control or FUNC. on
the unit.
A program can contain 20 tracks/files.
3. Select a track/file you want to play by pressing
C/V.
2.Press PROGRAM/MEMORY on the remote
control in stop status.
Do this
Press Z ENTER.
Press d/M.
During playback, Press d/M.
During playback, press C/V
Skipping to to go to the next track/file or to
the next/ return to the beginning of the
previous current track/file.
track/file Press C twice briefly to step
back to the previous track/file.
Selecting
a track/file
directly
Press 0 to 9 numerical buttons on
the remote control to go to the
desired file or track directly.
Searching
Press and hold C/V during
for a section
playback and release it at the point
within
you want to listen to.
a track/file
Press REPEAT(MENU) on the
remote control repeatedly. The
Playing
display changes in the following
repeatedly or order.
randomly RPT1 -> RPT *DIR (only MP3/WMA)
-> RPT ALL -> RANDOM -> OFF.
*DIR : Directory
1. Insert a CD or a USB and wait for it to be
ordered.
3.Press C/V on the remote control or
Y/U on the unit to select a track/file.
4.Press PROGRAM/MEMORY again to save and
select a next track/file.
5.Press d/M to play the programmed music
tracks/files.
6. To clear your selection, press Z ENTER twice.
,,Note
The programs are also cleared when the disc
or USB device is removed, the unit is powered
off or the function is switched to others.
3
Operating
To
Stop
Playback
Pause
13
14
Operating
Displaying file information
(ID3 TAG)
While playing an MP3 file containing file
information, you can display the information by
pressing INFO.
Searching for a folder
1.Press PRESET·FOLDER W/S repeatedly until a
desired folder appears on the display window.
2.Press d/M to play it.
The first file of the folder will be played.
3
Turn off the sound temporarily
Press MUTE@ to mute your unit.
Operating
You can mute your unit, for example, to answer the
telephone, the “MUTE” is displayed in the display
window.
To cancel it, press MUTE@ again on the remote
control or change the volume level.
Deleting an MP3/WMA file
You can delete a file, folder or format by pressing
DELETE. (USB only)
1.Press DELETE repeatedly during selecting
the MP3/WMA file. This function is supported
only in stop status. The display changes in the
following order.
- DEL FILE : Deletes file.
- DEL DIR : Deletes folder.
- FORMAT : Formats USB.
2. To delete file/folder or format, press d/M
on the remote control or press T ST./MO. on
the unit.
3. If you want to exit the current mode,
press Z ENTER on the remote control or
press I on the unit.
>>Caution
yy Do not extract the USB device during
operation.(play, delete, etc.)
yy Regular back up is recommended to
prevent data loss.
yy The delete function may not be supported
according to the USB status.
Operating
DEMO
AUTO DJ playback
In the power off state, it demonstrates the function
on display window by pressing SET/DEMO.
To cancel the DEMO, press it again.
Auto DJ blends the end of one song into the
beginning of another for seamless playback. It
equalizes volume across tracks for uninterrupted
playback.
,,Note
yy While DEMO, this unit will keep DEMO
status even if you unplug the power cord
connection.
yy You can enjoy other functions during
the DEMO. Then the DEMO will pause to
temporary.
- Without input key in 10 sec, the DEMO
will play back automatically.
15
Press AUTO DJ on the remote control or unit
repeatedly, the display changes as followings.
RANDOM (AUTO DJ RANDOM) -> RPT (AUTO DJ
SEQUENTIAL) -> (AUTO DJ OFF)
Mode
OFF
Display
Window
(AUTO DJ OFF)
Description
-
RANDOM
(AUTO DJ
RANDOM)
The music is
played randomly
on this mode.
REPEAT
RPT
(AUTO DJ
SEQUENTIAL)
The music is
played repeatedly
on this mode.
,,Note
yy Searching for a section within a track/file
or playing repeatedly or randomly is not
supported on the AUTO DJ mode.
yy If you move to other functions or stop the
music using I on the unit (or Z ENTER on
the remote control) on AUTO DJ mode,
AUTO DJ function will be disable.
yy AUTO DJ function is not supported in the
music file whose length is less than 60
seconds.
yy During recording, AUTO DJ function is not
available.
yy If you change a disc while the AUTO DJ
function is activated, the function is
deactivated.
3
Operating
RANDOM
16
Operating
Radio Operations
Be sure that FM/AM aerial is connected.
(Refer to the page 12)
Listening to the radio
1.Press FUNCTION on the remote control or
FUNC. on the unit until FM or AM appears in
the display window.
The last received station is tuned in.
3
2. Press and hold TUNING-/+ on the remote
control or Y/U on the unit for about two
seconds until the frequency indication starts to
change, then release. Scanning stops when the
unit tunes in a station.
Operating
Or
Press TUNING-/+ on the remote control or
Y/U on the unit repeatedly.
3. Adjust the volume by rotating volume knob on
the unit or by pressing VOL +/- on the remote
control repeatedly.
Presetting the Radio Stations
You can preset 50 stations for FM and AM.
Before tuning, make sure to turn down the volume.
1.Press FUNCTION on the remote control or
FUNC. on the unit until FM/AM appears in the
display window.
2. Select the desired frequency by pressing
TUNING-/+ on the remote control or
Y/U on the unit.
3.Press PROGRAM/MEMORY a preset number
will flash in the display window.
4.Press PRESET·FOLDER W/S to select the
preset number you want.
5.Press PROGRAM/MEMORY. The station is
stored.
6. Repeat steps 2 to 5 to store other stations.
7. To listen to a preset station, press
PRESET·FOLDER W/S or 0 to 9 numerical
buttons.
Deleting all the saved stations
1. Press and hold PROGRAM/MEMORY for two
seconds. “ERASE ALL” will flash up on the unit
display.
2.Press PROGRAM/MEMORY to erase all saved
radio stations.
Improving poor FM reception
Press T ST./MO. on the unit or d/M on the
remote control. This will change the tuner from
stereo to mono and usually improve the reception.
Operating
Sound adjustment
Setting the surround mode
This system has a number of pre-set surround
sound fields. You can select a desired sound mode
by using SOUND EFFECT on the remote control or
LG EQ on the unit.
The displayed items for the Equalizer may be
different depending on sound sources and effects.
Description
NATURAL
You can enjoy comfortable and
natural sound.
Local
Specialization
equalizer
Regionally optimized sound
effect. (FORRO/FUNK/
SERTANEJO/DANGDUT/ARABIC/
PERSIAN/INDIA/REGUETON/
MERENGUE/SALSA/SAMBA/
CUMBIA/AFRO HIP HOP)
AUTO EQ
Realizes the sound equalizer that
is the most similar to the genre
of which is included in the MP3
ID3 tag of song files.
POP
CLASSIC
JAZZ
ROCK
This program lends an
enthusiastic atmosphere to the
sound, giving you the feeling
you are at an actual rock pop,
jazz or classic concert.
MP3 -- OPT
This function is optimized
for compressible MP3 file. It
improves the treble sound.
BASS
Reinforces the treble, bass and
surround sound effect.
LOUDNESS
Improves the bass and treble
sound.
BYPASS
You can enjoy the sound
without equalizer effect.
,,Note
yy On some speakers, sound may not be heard
or heard in low sound depending on the
sound mode.
yy Maybe you need reset the surround mode,
after switching the input, sometimes even
after the sound track changed.
yy By pressing BASS BLAST on the unit you
can directly select the BYPASS or
BASS BLAST sound.
3
Operating
On Display
17
18
Operating
Setting the Clock
Setting the alarm
1. Turn the unit on.
You can use the unit as an alarm clock.
You have to set the clock before setting the alarm.
2.Press CLOCK for at least 2 seconds.
1. Turn the unit on.
3. Choose time mode by pressing Y/U.
2.Press TIMER. Each of functions flashes.
- AM 12:00 (for an AM and PM display)
or 0:00 (for a 24 hour display)
4.Press SET/DEMO to confirm your selection.
5. Select the hours by pressing Y/U.
6.Press SET/DEMO.
7. Select the minutes by pressing Y/U.
4. “ON TIME” will be displayed. This is your desired
time to the unit turns on. Press Y/U to
change the hours and minutes and press
SET/DEMO to save.
5. The “OFF TIME” will be displayed. This is your
desired time to the unit turns off.
3
6.Press Y/U to change the hours and
minutes and press SET/DEMO to save.
Operating
8.Press SET/DEMO.
3.Press SET/DEMO when the function you want
to be woken by is showing.
7.Press Y/U to change the volume and
press SET/DEMO to save. The clock icon "(“
shows that the alarm is set.
8.Press TIMER button 2 times. You can check the
setting status.
,,Note
yy If you set the clock time, you can check the
time by pressing CLOCK even when the
player is turned off.
yy If you set the clock time and alarm, you
can check the alarm icon “(“ by pressing
CLOCK even when the player is turned off.
yy If you set the clock time and alarm, you
can check the alarm icon “(“ and setting
informaiton by pressing TIMER even when
the unit is turned off.
yy Alarm function is not supported even if
you choose USB function as an alarm clock
when iPod/iPhone is connected to USB
port.
Operating
19
Sleep Timer Setting
Press SLEEP repeatedly to select delay time
between 10 and 180 minutes. After the delay time,
the unit will be turned off.
To cancel the sleep function, press SLEEP
repeatedly until “SLEEP 10” appears, and then press
SLEEP once again while “SLEEP 10” is displayed.
,,Note
yy You can check the remaining time before
the unit is turned off.
yy Press SLEEP. The remaining time appears in
the display window.
Press SLEEP once. The display window will
be darkened by half. To cancel it, press SLEEP
repeatedly until dim off.
3
Operating
Dimmer
20 Operating
Advanced Operations
Playing the iPod/iPhone
You can enjoy the sound with your iPod/iPhone.
For details about iPod/iPhone, refer to the iPod/
iPhone User Guide.
1. Connect iPod/iPhone to the USB port on the
front of the unit by using the iPod/iPhone cable.
To
ON UNIT
Do this
ON REMOTE
Pause or
restart
T
ST./MO.
d/M
Skip
Y/U
C/V
Search
Press and hold
Y/U
Press and hold
C/V
-
REPEAT
(MENU)
Move to the
desired item
-
PRESET·
FOLDER
W/S
Choose an
item
I
Z ENTER
Move to the
Previous
menu
3
Operating
Compatible iPod/iPhone
We recommend installing the latest software
version.
The unit supports the models as follows.
If you turn this unit on, your iPod/iPhone will be
automatically turned on and start recharging.
2.Press FUNC. on the unit or FUNCTION on the
remote control to select USB function. You can
operate your iPod/iPhone through an iPod/
iPhone’s display by using the remote control
and also control on your iPod/iPhone.
yy iPod touch 1 G, 2 G, 3 G, 4 G
yy iPod classic
yy iPod nano 2 G, 4 G, 5 G, 6 G
yy iPhone 4S
yy iPhone 4
yy iPhone 3GS
yy iPhone 3G
Depending on your iPod/iPhone’s software version,
you may not control your iPod/iPhone from the
unit.
Operating
,,Note
yy If this unit displays error message “NO USB”
follow check procedure below.
21
Listening to the sound from
your external device
- Your iPod/iPhone is not connected firmly.
- This unit recognizes your iPod/iPhone as
an unknown device.
- Your iPod/iPhone is exceptionally low in
power.
The unit can be used to play the sound from many
types of external device. (Refer to the page 11)
/ The battery needs to be charged.
/If you charge the battery while iPod/
iPhone is extremely low in power,
it may take longer to be charged.
3. Select the AUX function by pressing FUNC. on
the unit or FUNCTION on the remote control.
1. Connect the external device to the AUX IN
connector of the unit.
2. Turn the power on by pressing 1/! (Power).
4. Turn the external device and start it playing.
Recording to USB
yy Depending on your iPod/iPhone’s software
version, it may not be possible to control
your iPod/iPhone from this unit. We
recommend installing the latest software
version.
1. Connect the USB device to the unit.
yy If you use an application, make a call, or
send and receive SMS text message, etc. on
iPod touch or iPhone, disconnect it from
this unit and then use it.
yy If you have a problem with your iPod/
iPhone, please visit www.apple.com/
support.
You can record a various sound source to USB.
(Except IPOD function)
2. Select a function by pressing FUNC. on the unit
or FUNCTION on the remote control.
One track/file recording - You can record to USB
after playing a track/file you want.
All tracks/files recording - You can record to USB
after stop.
Program list recording - After showing the
programmed list, you can record it to USB.
(Refer to the page 13)
3. Start the recording by pressing
USB REC
on the unit or USB REC on the remote control.
4. To stop recording, press I on the unit or
Z ENTER on the remote control.
Pausing recording
During recording, press
USB REC on the
unit or USB REC on the remote control to pause
recording. Press it again to restart recording.
(Only Radio/AUX)
3
Operating
yy iPod/iPhone does not support recording
function when connected.
22 Operating
To select recording bit rate
and speed
1.Press
USB REC on the unit or USB REC on
the remote control for longer than 3 seconds.
2.Use Y/U on the unit or C/V on the
remote control to select the bit rate.
yy During recording MP3/WMA, there is no
sound.
yy When you stop recording during playback,
the file that has been recorded at that time
will be stored. (Except MP3/WMA files)
96 kbps -> 128 kbps -> 192 kbps -> 256 kbps
3.Press
USB REC on the unit or USB REC on
the remote control again to select the recording
speed.
4.Press Y/U on the unit or C/V on
the remote control to select a desired recording
speed : (AUDIO CD only)
3
,,Note
yy You can check the recording percentage
rate for the USB record on the display
window during the recording.
(MP3/WMA CD Only)
yy Do not remove the USB device or turn
off the unit during USB recording. If not,
an incomplete file may be made and not
deleted on PC.
Operating
X1 SPEED
- You can listen to music while recording it.
yy If USB recording does not work, the
message like “NO USB”, “ERROR”, “FULL” or “NO
REC” is displayed on the display window.
X2 SPEED
- You can just record the music file.
yy Multi card reader device or External HDD
can not be used for USB recording.
5.Press
USB REC on the unit or USB REC on
the remote control to finish the setting.
yy A file is recorded by about 512 Mbyte when
you record for a long term.
yy You may not store more than 999 files.
yy It’ll be stored as follows.
AUDIO CD
MP3/WMA
The other
source*
* : TUNER, AUX and the like.
The making of unauthorized copies of copyprotected material, including computer
programs, files, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal offense.
This equipment should not be used for such
purposes.
Be responsible
Respect copyrights
4Troubleshooting
Troubleshooting 23
Troubleshooting
Problem
Cause & Correction
yy The power cord is not plugged in. Plug in the power cord.
No Power.
No sound.
yy Check whether electricity failed.
Check the condition by operating other electronic devices.
yy Check whether you select right function.
Press FUNCTION and check the selected function.
yy If not, connect speaker cables correctly.
Speaker cables connected correctly.
yy An unplayable disc is inserted. Insert a playable disc.
The unit does not start
playback.
yy No disc is inserted. Insert a disc.
yy The disc is dirty. Clean the disc. (Refer to the page 27)
yy The disc is inserted upside down.
Place the disc with the label or printed side facing upwards.
Radio stations cannot
be tuned in properly.
yy The signal strength of the radio station is too weak.
Tune to the station manually.
yy No stations have been preset or preset stations have been cleared (when
tuning by scanning preset channels).
Preset some radio stations, see page 16 for details.
yy The remote control is too far from the unit.
Operate the remote control within about 23 ft (7 m).
yy There is an obstacle in the path of the remote control and the unit.
The remote control
Remove the obstacle.
does not work properly.
yy The batteries in the remote control are exhausted.
Replace the batteries with new ones.
iPod/iPhone does not
work.
yy Check whether the player is connected to the unit correctly.
Connect it to the unit correctly.
Troubleshooting
yy The antenna is positioned or connected poorly.
Connect the antenna securely.
4
5Appendix
24 Appendix
Trademarks and
Licenses
“Made for iPod,” and “Made for iPhone” mean
that an electronic accessory has been designed
to connect specifically to iPod or iPhone,
respectively, and has been certified by the
developer to meet Apple performance standards.
Apple is not responsible for the operation of
this device or its compliance with safety and
regulatory standards. Please note that the use
of this accessory with iPod or iPhone may affect
wireless performance.
5
Appendix
Appendix 25
Specifications
General
Model
CM4620
Power requirements
200 - 240 V, 50 / 60 Hz
CM4520
Power consumption
70 W
Dimensions (W x H x D)
202 x 300 x 297 mm
Net Weight (Approx.)
2.85 kg
Operating temperature
5 °C to 35 °C (41 °F to 95 °F)
Operating humidity
5 % to 90 %
Bus Power Supply (USB)
USB DC 5 V 0 500 mA
55 W
CM4420
CM4320
55 W
45 W
Inputs
AUX IN
2.0 Vrms (1 kHz, 0 dB), 75 Ω, RCA jack (L, R) x 1
Tuner
FM Tuning Range
87.5 to 108.0 MHz or 87.50 to 108.00 MHz
AM Tuning Range
522 to 1 620 kHz, 520 to 1 710 kHz or 522 to 1 710 kHz
Amplifier
CM4620
CM4520
CM4420
CM4320
Stereo mode
220 W + 220 W
(3 Ω at 1 KHz,
THD 10 %)
130 W + 130 W
(4 Ω at 1 KHz,
THD 10 %)
130 W + 130 W
(4 Ω at 1 KHz,
THD 10 %)
80 W + 80 W
(4 Ω at 1 KHz,
THD 10 %)
220 W + 220 W
(3 Ω at 1 KHz,
THD 10 %)
130 W + 130 W
(4 Ω at 1 KHz,
THD 10 %)
130 W + 130 W
(4 Ω at 1 KHz,
THD 10 %)
80 W + 80 W
(4 Ω at 1 KHz,
THD 10 %)
Front
Surround
mode
Subwoofer
-
CD
Frequency Response
100 to 20 000 Hz
Signal-to-noise ratio
75 dB
Dynamic range
80 dB
160 W
(3 Ω at 1 KHz,
THD 10 %)
-
-
5
Appendix
Model
26 Appendix
Front speaker
Model
CMS4620F
Type
2 Way 2 Speaker
CMS4520F
CMS4520F
CMS4320F
Impedance
3Ω
4Ω
Rated Input Power
220 W
Max. Input power
440 W
130 W
130 W
80 W
260 W
260 W
160 W
Net Dimensions (W x H x D)
246 x 335 x 444
mm
232 x 249 x 344
mm
232 x 249 x 344
mm
215 x 237 x 304
mm
Net Weight
5 kg
3.2 Kg
3.2 Kg
2.47 Kg
Subwoofer speaker
Model
CMS4520W
Type
1 Way 1 Speaker
Impedance
3Ω
Rated Input Power
160 W
Max. Input power
320 W
Net Dimensions (W x H x D)
250 x 334 x 344 mm
Net Weight
5.4 kg
yy Design and specifications are subject to change without notice.
5
Appendix
Appendix 27
Maintenance
Notes on Discs
Handling Discs
Never stick paper or tape on the disc.
Storing Discs
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of heat
and never leave it in a parked car exposed to direct
sunlight.
Cleaning Discs
Do not use strong solvents such as alcohol,
benzine, thinner, commercially available cleaners,
or anti-static spray intended for old vinyl records.
Handling the Unit
When shipping the unit
Please save the original shipping carton and
packing materials. If you need to ship the unit, for
maximum protection, re-pack the unit as it was
originally packed at the factory.
Keeping the exterior surfaces clean
Do not use volatile liquids such as insecticide spray
near the unit.
Wiping with strong pressure may damage the
surface.
Do not leave rubber or plastic products in contact
with the unit for a long period of time.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not
use strong solvents such as alcohol, benzine, or
thinner, as these might damage the surface of the
unit.
Maintaining the Unit
Appendix
The unit is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty
or worn, the picture quality could be diminished.
For details, please contact your nearest authorized
service center.
5
Download PDF