LGEAP_XA12_ENG_MFL39672007
ENGLISH
MODEL : XA12
There is so much your Hi-Fi system can do
Play CDs
Go to page 6
Lull me to sleep
and wake me up
Go to page 7
Go to page 7
Contents
Setting up
About Player
About Remote control
Listening to the radio
Listening to CDs
Listening to music from your portable player
About MP3/WMA
Setting the Clock
Use your player as an alarm clock
Safety Precaution
Troubleshooting
Specifications
Play from many
external devices
3
4
5
6
6
7
7
7
7
8
9
9
Portable CD player
MP3 player
Before connecting, operating or adjusting this product, please read this instruction booklet carefully and completely.
2
MICRO Hi-Fi SYSTEM ] USER GUIDE
ENGLISH
Setting up
1 Connect the speaker cables to the player
Cables from the left-hand speaker connect to the terminal
marked L (left) + (plus) and - (minus). Cables from the right
hand speaker are connected to the terminal marked R
(right) + (plus) and - (minus).
To connect the cable to the player, press each of the four
square plastic finger pads on the rear of the player. The
connector will open ready to receive a cable.
3
#
Put the batteries in the remote control
Make sure that the + (plus) and - (minus)
on the batteries (size AAA) match those on
the remote control.
2 Fit the AM loop aerial to its
stand - OPTIONAL
Connect the AM loop aerial to the
player.
3 Connect the FM aerial
The reception will be at its best when the two
loose ends of the aerial are in a straight line and
horizontal.
4 Plug the power plug into a wall socket
MICRO Hi-Fi SYSTEM ] USER GUIDE
3
About Player
MO./ST.
This will change the tuner from stereo to
mono and usually improve the reception.
SET
SET confirms the time you have selected
when setting the clock. (see Setting the clock)
FUNC.
Change the functions between FM, AM
(OPTIONAL), CD, PORTABLE etc.
1/]] (POWER)
You can set up the unit into an economic
power save mode. In the power-on status,
press and hold 1/] (POWER) for about 3
seconds. To cancel power save mode, press
1/] (POWER).
PORTABLE IN
For connecting a portable device and playing
it through the system’s speakers.
4
MICRO Hi-Fi SYSTEM ] USER GUIDE
CD door
You can use it when inserting or removing CDs.
Don't open the door while CD plays back.
TIMER
With the TIMER function you can turn CD
play and radio reception on or off at a desired
time.
CLOCK
For setting the clock and checking the time.
VOLUME
Control the volume when using any function.
About Remote control
Search for a folder of MP3/WMA files
When a CD containing MP3/WMA files in
several folders is being played, press
PRESET/FOLDER to select the folder you
want to play.
Choose a ‘preset number’ for a radio
station (see Listening to the radio)
Fall asleep while listening to your player
Firstly, start a radio station or music. Press
SLEEP on the remote one or more times to
select delay time between 10 and 180 minutes, after the player will turn off.
Listen to your tracks again and again
Press REPEAT once to repeat the track currently playing. Press REPEAT twice to repeat
the whole CD, or if you’re listening to the
whole folder of MP3/WMA CD. The display
will show what is being repeated.
Sound quality adjustment
You can choose between 4 fixed sound
impressions. Select a desired sound mode by
using EQ.
(NORMAL → ROCK → POP → CLASSIC)
Temporarily stop the sound
Press the button again to return to the sound.
To change the functions
Change the functions between FM, AM
(OPTIONAL), CD or PORTABLE.
Use when playing a CD
For storing radio stations
If you have saved radio stations using PROGRAM/MEMO, you can scroll through them
and select one. (see Listening to the radio)
Listen to your tracks in any order
(see Listening to the CDs)
Search radio stations by radio type
- OPTIONAL (See Listening to radio)
eXtreme Dynamic Sound System
Reinforce the treble, bass and surround
sound effect. XDSS will show in the display.
Press again for NORMAL.
MP3 - OPT
Optimizes compressible MP3 files so that it
improves the bass sound.
(XDSS → MP3-OPT → NORMAL)
See information about your music
MP3/WMA files often come with tags.
The tag gives the Title, Artist, Album or Time
information. Press MP3 Info while a file is
playing to see this information.
MICRO Hi-Fi SYSTEM ] USER GUIDE
5
Listening to the radio
ON PLAYER
ON REMOTE
1. Select the FM (AM - OPTIONAL):
FUNC.
FUNCTION
2. Select the radio station:
TUNING-/TUNING+
TUN.-/TUN.+
3. To ‘save’ a radio station:
PROGRAM/MEMO
A preset number will show in
the display.
4. To select a ‘saved’ station:
PRESET/FOLDER
Up to 50 radio stations can be
saved.
5. To confirm press:
PROGRAM/MEMO
Listening to the radio - more you can do
See information about your radio stations - OPTIONAL
The FM tuner is supplied with the Radio Data System (RDS) facility. This
shows the letters RDS on the display, plus information about the radio station being listened to. Press RDS on the remote control several times to
view the information.
PTY - Programme Type, such as News, Sport, Jazz Music.
RT - Radio Text, the name of the radio station.
CT - Time Control, the time at the location of the radio station.
PS - Programme Service name, the name of channel.
You can search the radio stations by programme type by pressing RDS.
The display will show the last PTY in use. Press PTY one or more times to
select your preferred programme type. Press and hold PTY SEARCH. The
tuner will search automatically. When a station is found the search will
stop.
Look for radio stations automatically
Press TUNING - /TUNING + on the front panel (or press TUN.- / TUN.+ on
the remote control for more than 0.5 second. The tuner will scan
automatically and stop when it finds a radio station.
Delete all the saved stations
Press and hold PROGRAM/MEMO for two seconds. “CLEAR” shows.
Press PROGRAM/MEMO to erase all the saved stations.
6
MICRO Hi-Fi SYSTEM ] USER GUIDE
Choose a ‘preset number’ for a radio station
Select a station you want by pressing TUN.- / TUN.+ on the remote control
or TUNING - /TUNING + on the front panel. Press PROGRAM/MEMO, the
station flashes. Press PRESET/FOLDER on the remote control to select
the preset number you want. Press PROGRAM/MEMO to save it.
Listening to CDs
ON PLAYER
1. Open the CD door:
2. Insert the CD :
Label facing up.
3. Close the CD door:
The display will show the total
number of tracks (files).
4. Select the CD function:
5. Start the CD playing:
6. To stop a CD playing:
ON REMOTE
PUSH OPEN
PUSH OPEN
FUNC.
FUNCTION
B/[]
x
B/[]
x
Listening to CDs - more you can do
Pause or restart a CD
Press B/[] during playback. Press this button again to resume play.
Search for a section within a track
Hold ./> on the front panel or .bb/BB> on the remote control.
(This function is only available for Audio CD’s.)
Skip to another track
Press ./> on the front panel or .bb/BB> on the remote control.
Listen to your tracks in any order
Up to 20 tracks on a CD can be listened to in the order of your choice.
Insert a CD and wait for it to be read. Press PROGRAM/MEMO on the
remote control, then use ./> to select the track. Press
PROGRAM/MEMO again to save and select the next track. Press B/[].
To clear your selection, press STOP, PROGRAM/MEMO, STOP.
Listening to music from
your portable player
Setting the Clock
ON PLAYER
The player can be used to play the music from many
types of portable player.
ON PLAYER
1. Connect the portable player by
plugging the unit into
PORTABLE IN on the front of
the player.
2. Turn the power on:
3. Select the PORTABLE function:
4. Turn the portable player on
and start it playing:
1 /]]
FUNC.
ON REMOTE
POWER
FUNCTION
About MP3/WMA
MP3/WMA Disc compatibility with this unit is limited as follows:
• Sampling Frequency
8 - 48 kHz (MP3), 32 - 48 kHz (WMA)
• Bit rate
8 - 320 kbps (MP3), 48 - 320 kbps (WMA)
• CD-R physical format should be “ISO 9660”
• If you record MP3/WMA files using the software which cannot create a
FILE SYSTEM, for example “Direct-CD” etc., it is impossible to playback
MP3 files. We recommend that you use “Easy-CD Creator”, which creates
an ISO 9660 file system.
• File names should be named using 30 letters or less and must incorporate “.mp3”,“.wma” extension e.g. “********.MP3” or “********.WMA”
• Do not use special letters such as “/ : * ? “ < >”etc.
• Even if the total number of files on the disc has more than 1000, it will
only be shown up to 999.
1. Press for at least 2 seconds:
2. Choose from either:
AM 12:00 (for an am and pm display) or 0:00 (for a
24 hour display).
3. Confirm your selection:
4. Select the hours:
5. Press:
6. Select the minutes:
7. Press:
CLOCK
./>
SET
./>
SET
./>
SET
Use your player as an alarm clock
Press and hold TIMER for two seconds. Each function, TUNER, CD
flashes for two seconds. Press SET when the function you want to be
woken by is showing.
If you choose TUNER you will be shown the stations you have saved as
presets. Use .or > to select the station you want, then press SET.
You will be shown the ON TIME display. This is where you set the time you
want the alarm to go off. Use .or > to change the hours and minutes
and SET to save. You will then be shown the OFF TIME display. This is
where you set the time you want the function to stop. Use .or > to
change the hours and minutes and press SET to save.
Next you will be shown the volume (VOL) you want to be woken by.
Use .or > to change the volume and SET to save. Switch the system
off. The clock icon shows that the alarm is set.
When the system is turned off you can check the time the alarm is set for
by pressing TIMER. You can also turn the alarm on and off by pressing
TIMER. To set the alarm to go off at a different time, switch the system on
and re programme following the same steps above.
MICRO Hi-Fi SYSTEM ] USER GUIDE
7
Safety Precaution
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT
REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol within an equilateral triangle is intended to
alert the user to the presence of non insulated dangerous voltage within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT
EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
CAUTION: The apparatus should not be exposed to water (dripping or splashing) and no objects
filled with liquids, such as vases, should be placed on the apparatus.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit;
That is, a single outlet circuit which powers only that appliance and has no additional outlets or
branch circuits. Check the specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension
cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these
conditions could result in electric shock or fire. Periodically examine the cord of your appliance,
and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an LG Authorised Service
Centre.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched,
closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where
the cord exits the appliance.
To disconnect power from the mains, pull out the mains cord plug. When installing the product,
ensure that the plug is easily accessible.
WARNING: Do not install this equipment in a confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of
the product and to protect it from over heating.
The openings should be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer's instruction has been adhered to.
CAUTION:
This product employs a Laser System.
To ensure proper use of this product, please read this owner’s manual carefully and retain it for
future reference. Should the unit require maintenance, contact an authorized service center.
Use of controls, adjustments or the performance of procedures other than those specified herein
may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation
when open. DO NOT STARE INTO BEAM.
8
MICRO Hi-Fi SYSTEM ] USER GUIDE
• The appliance is not intended for use by young children or infirm persons without supervision.
• Young Children should be supervised to ensure that they do not play with appliance.
• If the appliance is supplied from a cord extension set or an electrical portable outlet device, the
cord extension set on electrical portable outlet device must be positioned so that it is not subject
to splashing or ingress of moisture.
Troubleshooting
Symptom
No power
No sound
The unit does not
start playback
The remote
control does not
work properly
Specifications
Cause
Correction
• Plug the power cord into the wall
outlet securely.
• The power of the external source • Switch on the external source
equipment.
equipment is turned off.
• Set the speaker cable to the cor• The speaker cable is connected
rect position, then turn on the unit
to a wrong position.
again by pressing POWER.
• Insert a playable disc.
• An unplayable disc is inserted.
• Place the disc with the playback
• The disc is placed upside down.
side down.
• Place the disc on the disc tray
• The disc is not placed within the
correctly inside the guide.
guide.
• Clean the disc.
• The disc is dirty.
• The remote control is not pointed • Point the remote control at the
remote sensor of the unit.
at the remote sensor of the unit.
• The remote control is too far from • Operate the remote control within
about 23 ft (7 m).
the unit.
• Remove the obstacle.
• There is an obstacle in the path
of the remote control and the unit.
• Replace the batteries with new
• The batteries in the remote conones.
trol are exhausted.
• The power cord is disconnected.
General
Net Weight
1.5 kg
External dimensions (WxHxD) 150 x 150 x 205 mm
Tuner
FM Tuning Range
87.5 - 108.0 MHz or 65 - 74 MHz,
87.5 - 108.0 MHz
AM Tuning Range - OPTIONAL
522 - 1620 kHz or 520 - 1720 kHz
Amplifier
Output Power
5 W + 5 W (T.H.D 10 %)
Frequency Response
30 - 20000 Hz
Signal-to-noise ratio
75 dB
CD
Frequency response
40 - 20000 Hz
Signal-to-noise ratio
75 dB
Dynamic range
75 dB
Speakers (XAS12F)
Type
1 Way 1 Speaker
Impedance
6Ω
Frequency Response
100 - 17000 Hz
Sound Pressure Level
84 dB/W (1m)
Rated Input Power
5W
Max. Input Power
10 W
Net Dimensions (WxHxD)
150 x 150 x 150 mm
Net Weight (1EA)
0.99 kg
Designs and specifications are subject to change without notice.
MICRO Hi-Fi SYSTEM ] USER GUIDE
9
P/NO : MFL39672007
Download PDF

advertising