OWNER’S MANUAL
Micro Hi-Fi System
Please read this manual carefully before operating
your set and retain it for future reference.
XA146 (XA146, XAS146F)
XA146-F0P-AAUSLL-ENG.indd 1
11. 12. 02
1:52
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing) instructions
in the literature accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
XA146-F0P-AAUSLL-ENG.indd 2
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance,
contact an authorized service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try
to open the enclosure. Visible laser radiation when
open. DO NOT STARE INTO BEAM.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an exact
replacement part by an authorized service center.
Protect the power cord from physical or mechanical
abuse, such as being twisted, kinked, pinched,
closed in a door, or walked upon. Pay particular
attention to plugs, wall outlets, and the point where
the cord exits the appliance. To disconnect power
from the mains, pull out the mains cord plug. When
installing the product, ensure that the plug is easily
accessible.
11. 12. 02
1:52
Getting Started
3
This device is equipped with a portable battery or
accumulator.
Safety way to remove the battery or the battery
from the equipment: Remove the old battery
or battery pack, follow the steps in reverse order
than the assembly. To prevent contamination of
the environment and bring on possible threat
to human and animal health, the old battery or
the battery put it in the appropriate container at
designated collection points. Do not dispose of
batteries or battery together with other waste.
It is recommended that you use local, free
reimbursement systems batteries and accumulators.
The battery shall not be exposed to excessive heat
such as sunshine, fire or the like.
1
Getting Started
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
• The appliance is not intended for use by young
children or infirm persons without supervision.
• Young Children should be supervised to ensure
that they do not play with appliance.
• If the appliance is supplied from a cord
extension set or an electrical portable outlet
device, the cord extension set on electrical
portable outlet device must be positioned so
that it is not subject to splashing or ingress of
moisture.
XA146-F0P-AAUSLL-ENG.indd 3
11. 12. 02
1:52
4
Table of Contents
Table of Contents
1
Getting Started
2
5
5
5
5
5
5
6
7
8
Safety Information
Unique Features
Accessories
Playable file Requirement
– MP3/ WMA music file requirement
– Compatible USB Devices
– USB device requirement
Remote control
Front panel
Rear panel
2
Connecting
9
9
9
9
10
Connecting to speakers
– Attaching the speakers to the unit
Optional Equipment Connection
– PORT. IN Connection
– USB Connection
3
Operating
11
11
11
11
11
Basic Operations
– CD/ USB Operations
Other Operations
– Programmed Playback
– Displaying file information
(ID3 TAG)
– Turn off the sound temporarily
Radio Operations
– Listening to the radio
– Presetting the Radio Stations
– Deleting all the saved stations
– Improving poor FM reception
Sound adjustment
– Setting the surround mode
Setting the Clock
– Using your player as an alarm clock
– Sleep Timer Setting
– Dimmer
11
12
12
12
12
12
13
13
13
14
14
14
XA146-F0P-AAUSLL-ENG.indd 4
15
15
15
16
16
16
Advanced Operations
– Playing the iPod
– Compatible iPod
– Listening to music from your external
device
– Recording to USB
– To select recording bit rate and speed
4
Troubleshooting
18
Troubleshooting
5
Appendix
19
20
20
20
20
Specifications
Maintenance
– Handling the Unit
– Notes on Discs
Trademarks and Licenses
11. 12. 02
1:52
Getting Started
Unique Features
USB Direct Recording
•
Maximum files : Under 999
•
File extensions : “.mp3”/ “.wma”
CD-ROM file format : ISO9660/ JOLIET
•
We recommend that you use Easy-CD Creator,
which creates an ISO 9660 file system.
Records music to your USB device.
Portable In
Compatible USB Devices
Listens to music from your portable device. (MP3,
Notebook, etc)
•
MP3 Player : Flash type MP3 player.
•
USB Flash Drive :
Devices that support USB2.0 or USB1.1.
•
The USB function of this unit does not support
all USB devices.
Made for iPod
Enjoy music from iPod® with simple connection.
USB device requirement
Accessories
•
Devices which require additional program
installation when you have connected it to a
computer, are not supported.
•
Do not extract the USB device while in
operation.
•
For a large capacity USB, it may take longer than
a few minute to be searched.
Please check and identify the supplied accessories.
Battery (1)
1
Getting Started
•
5
Remote Control (1)
Portable in cable
(Optional) (1)
Playable file
Requirement
•
To prevent data loss, back up all data.
•
If you use a USB extension cable or USB hub, the
USB device is not recognized.
•
Using NTFS file system is not supported. (Only
FAT(16/ 32) file system is supported.)
•
This unit is not supported when the total
number of files is 1 000 or more.
•
External HDD, Card readers, Locked devices, or
hard type USB devices are not supported.
•
USB port of the unit cannot be connected to
PC. The unit cannot be used as a storage device.
MP3/ WMA music file
requirement
MP3/ WMA file compatibility with this unit is limited
as follows :
•
Sampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
•
Bit rate : within 32 to 320 kbps (MP3),
40 to 192 kbps (WMA)
XA146-F0P-AAUSLL-ENG.indd 5
11. 12. 02
1:52
6
Getting Started
Remote
control
1
• • • • • • a • • • • • •
Z ENTER :
POWER : Switches the unit ON
or OFF.
- Stops playback or recording.
- choose an item(iPod).
Getting Started
EQ : Chooses sound impressions.
d/M (Play/Pause) :
LG EQ : Selects a natural
equalizer effect by using LG EQ.
- Starts or pauses playback.
- Selects Mono/ Stereo.
OPEN/CLOSE : Opens and closes
the disc tray.
PROGRAM/MEMO:
• • • • • • b • • • • •
PRESET/FOLDER W/S :
Searches for a folder of MP3/
WMA files. When a CD/ USB
containing MP3/ WMA files in
several folders is being played,
press PRESET/FOLDER W/S
to select the folder you want to
play. Choose a ‘preset number’
for a radio station.
- For storing radio stations if you
have saved radio stations using
PROGRAM/MEMO, you can
scroll through them and select
one.
- Listens to your tracks in any
order.
X REC : USB direct recording.
FUNCTION : Selects the function
and input source.
VOLUME W/S : Adjusts speaker
volume.
@ MUTE : Mutes the sound.
• • • • • • c • • • • •
Battery Installation
SLEEP: Sets the system to turn
off automatically at a specified
time.
(Dimmer : The display window
will be darkening by half.)
MENU/REPEAT :
- Listens to your tracks
repeatedly or randomly. (only
in CD/USB)
- Move to the previous
menu(iPod).
Remove the battery cover on the
rear of the Remote Control, and
insert one (size AAA) battery with
4 and 5 matched correctly
INFO : Checks information about
your music. MP3 files often
come with tags. The tag gives
the Title, Artist, Album or Time
information.
TUN. -/+ : Selects the radio
station.
Cc/vV (Skip/
Search):
- Skips Fast backward or
Forward.
- Searches for a section within a
track.
XA146-F0P-AAUSLL-ENG.indd 6
11. 12. 02
1:52
Getting Started
7
Front panel
2
1
3
4
1
Getting Started
5
7
6
8
9
10
11
a 1/! (POWER)
Switches the unit ON or OFF.
12
13
14
15
h Disc Slot
b FUNC. (FUNCTION)
Changes the input source or function.
i PORT. IN
Connects to a portable player with audio
outputs.
c EQ
You can choose fixed sound impression.
j PHONES
Headphone jack
d iPod dock
k CLOCK
You can set and check the time.
e Display window
Shows the current status of the unit.
f T(PLAY / PAUSE)
- Starts playback.
- Pauses playback temporarily, press again to
exit pause mode.
- Selects Mono/ Stereo.
I (STOP)
Stops playback.
/ (Skip/Search):
- Goes to next or previous file/track.
- Searches backward or forward (Press and
hold)
- Tunes in the desired radio station.
l TIMER
You can turn CD, USB play and TUNER reception
on or off at a desired time.
m SET
Confirms the setting
n REC.
Recording to USB.
o USB Port
Connects an USB device.
R (OPEN/CLOSE)
Opens and closes the disc tray.
g VOL.
Adjusts speaker volume.
XA146-F0P-AAUSLL-ENG.indd 7
11. 12. 02
1:52
8
Getting Started
Rear panel
1
Getting Started
3
1
a ANTENNA (FM)
2
c Power cord
b Speaker terminal
XA146-F0P-AAUSLL-ENG.indd 8
11. 12. 02
1:52
Connecting
Connecting to
speakers
Optional Equipment
Connection
Attaching the speakers to the
unit
PORT. IN Connection
Connect connector on the speaker cable to speaker
terminal.
9
Connect an output (earphone or line out) of
portable device (MP3 or PMP etc) to the
2
PORT. IN connector.
Connecting
Each speaker connector is colored.
Use matching color connector to each speaker
terminal. When connecting connector to the
speaker terminal, push the connector until it is
perfectly linked.
MP3 player, etc...
> Caution
y The speakers contain magnet parts, so color
irregularity may occur on the TV screen or
PC monitor screen. Please use the speakers
far away from either TV screen or PC
monitor.
y Make sure to install the speaker with other
people in order to prevent it from falling
and causing injuries to the installer.
XA146-F0P-AAUSLL-ENG.indd 9
11. 12. 02
1:52
10
Connecting
USB Connection
Connect the USB port of USB Memory (or MP3
player, etc.) to the USB port on the front of the unit.
2
Connecting
, Note
y Removing the USB Device from the unit
1. Choose a different function/ mode or
press Z ENTER on the remote control
or I on the unit twice in a row.
2. Remove the USB device from the unit
y You can not use iPod by connecting USB
port.
y when you connect iPod to USB port , it is
not recharged.
XA146-F0P-AAUSLL-ENG.indd 10
11. 12. 02
1:52
Operating
Basic Operations
Other Operations
CD/ USB Operations
Programmed Playback
1. Insert the disc by pressing OPEN/CLOSE on
the remote control or R(OPEN/CLOSE) on the
unit or connect the USB device to the USB port.
The program function enables you to store your
favorite files/tracks from any disc or USB device.
2. Select the CD or USB function by pressing
FUNCTION on the remote control or FUNC. on
the unit.
1. Insert a CD or USB and wait for it to be order.
3. Select a file (or track) you want to play by
pressing C/V on the remote control or
on the unit.
/
Do this
Press Z ENTER on the remote
Stop
control or I on the unit.
Press d/M on the remote control
Playback
or T on the unit.
Press d/M on the remote control
Pause
or T on the unit.
During playback, press C/V
on the remote control or
/
Skipping to on the unit to go to the next track/
the next/ file or to return to the beginning of
previous the current track/ file.
track/ file Press C on the remote control
Searching
for a section
within a track
Searching
for a section
within a folder
Playing
repeatedly or
randomly
or
on the unit twice briefly to
step back to the previous track/ file.
Press and hold C/V on the
on the
remote control or
/
unit during playback and release it
at the point you want to listen.
Press PRESET/FOLDER W/S and
then d/M on the remote control or
T on the unit.
Press MENU/REPEAT on the
remote control repeatedly, the
display change in the following
order, RPT1 -> RPT ALL -> RANDOM
-> OFF
XA146-F0P-AAUSLL-ENG.indd 11
A program can contain 64 files/tracks.
2. Press PROGRAM/MEMO on the remote control
in stop status.
3. Press C/V on the remote control or
on the unit in stop status.
/
4. Press PROGRAM/MEMO again to save and
select a next file/track.
3
5. Press d/M on the remote control or T on the
unit to play the programmed music files.
Operating
To
11
6. To clear your selection, press ZENTER on the
remote control or I on the unit twice.
, Note
The programs are also cleared when the disc
or USB device is removed, the unit is powered
off or the function is switched to others.
Displaying file information
(ID3 TAG)
While playing an MP3 file containing file
information, you can display the information by
pressing INFO.
, Note
Sometimes INFO can not be executed to
according to ID3 TAG version.
Turn off the sound temporarily
Press @ MUTE to mute your unit.
You can mute your unit, for example, to answer
the telephone, the “MUTE ON” or “MUTE OFF” is
displayed in the display window.
11. 12. 02
1:52
12
Operating
Radio Operations
Listening to the radio
1. Press FUNCTION on the remote control or
FUNC. on the unit until FM appears in the
display window.
The last received station is tuned in.
2. Press and hold TUN -/+ for about two seconds
until the frequency indication starts to change,
then release. Scanning stops when the unit
tunes in a station.
Deleting all the saved stations
1. Press and hold PROGRAM/MEMO for two
seconds. “ERASE ALL” will flash up on the unit
display.
2. Press PROGRAM/MEMO to erase all saved radio
stations.
Improving poor FM reception
Press d/M on the remote control or T on the
unit. This will change the tuner from stereo to
mono and usually improve the reception.
Or
3
Press TUN -/+ repeatedly.
Operating
3. Adjust the volume by rotating VOL. on the unit
or by pressing VOLUME W/S on the remote
control repeatedly.
Presetting the Radio Stations
You can preset 50 stations for FM .
Before tuning, make sure to turn down the volume.
1. Press FUNCTION on the remote control or
FUNC. on the unit until FM appears in the
display window.
2. Select the desired frequency by pressing TUN
-/+.
3. Press PROGRAM/MEMO a preset number will
flash in the display window.
4. Press PRESET/FOLDER W/S to select the
preset number you want.
5. Press PROGRAM/MEMO The station is stored.
6. Repeat steps 2 to 5 to store other stations.
7. To listen a preset station, press
PRESET/FOLDER W/S.
XA146-F0P-AAUSLL-ENG.indd 12
11. 12. 02
1:52
Operating
Sound adjustment
13
Setting the Clock
1. Turn the unit on.
Setting the surround mode
2. Press CLOCK for at least 2 seconds.
This system has a number of pre-set surround
sound fields. You can select a desired sound mode
by using EQ or LG EQ.
3. Choose time mode by pressing C/V on
the remote control or
on the unit.
/
The displayed items for the Equalizer may be
different depending on sound sources and effect.
- AM 12:00 (for an AM and PM display) or 0:00
(for a 24 hour display)
4. Press SET to confirm your selection.
On Display
Description
NATURAL
You can enjoy comfortable and
natural sound.
AUTO EQ
Realizes the sound equalizer that
is the most similar to the genre
of which is included in the MP3
ID3 tag of song files.
POP
CLASSIC
JAZZ
ROCK
This program lends an
enthusiastic atmosphere to the
sound, giving you the feeling
you are at an actual rock pop,
jazz or classic concert.
MP3 -- OPT
This function is optimized for
compressible MP3, WMA file. It
improves the treble sound.
BASS BLAST
Reinforces the treble, bass and
surround sound effect.
VIRTUAL
You can enjoy more virtual
surround sound.
BYPASS
You can enjoy the sound
without equalizer effect.
6. Press SET to save.
7. Select the minutes by pressing C/V on
on the unit.
the remote control or
/
8. Press SET to save.
3
Operating
Local
Specialization
equalizer
Regionally optimized sound
effect. (FORRO/ FUNK/
SERTANEJO/ DANGDUT/
ARABIC/ PERSIAN/ INDIA/
REGUETON/ MERENGUE/ SALSA/
SAMBA/ CUMBIA/ AFRO)
5. Select the hours by pressing C/V on the
on the unit.
remote control or
/
, Note
Maybe you need reset the surround mode,
after switching the input, sometimes even
after the sound track changed.
XA146-F0P-AAUSLL-ENG.indd 13
11. 12. 02
1:52
14
Operating
Using your player as an alarm
clock
1. Turn the unit on.
2. Press TIMER. Each functions flashes.
3. Press SET when the clock you want to be
woken up is showed.
3
Sleep Timer Setting
Press SLEEP repeatedly to select delay time
between 10 and 180 minutes. After the delay time,
unit will turn off.
To cancel the sleep function, press SLEEP
repeatedly until “SLEEP 10” appears, and then press
SLEEP once again while “SLEEP 10” is displayed.
4. “ON TIME” will be displayed. This is your desired
time to unit turns on. Press C/V on the
remote control or
on the unit to
/
change the hours and minutes and press
SET to save.
y You can check the remaining time before
the unit turns off.
5. The “OFF TIME” will be displayed. This is your
desired time to unit turns off.
y Sleep function will work after dimmer.
, Note
y Press SLEEP. The remaining time appears in
the display window.
Operating
6. Press C/V on the remote control or
on the unit to change the hours and
/
minutes and press SET to save.
Dimmer
7. Press C/V on the remote control or
on the unit to change the volume
/
and press SET to save.
Press SLEEP once. The display window will be
darkening by half. To cancel it, press SLEEP
repeatedly until dim off.
8. Press TIMER button 2 times. You can check the
setting status.
, Note
y If you set the clock time, you can check the
time by pressing CLOCK even when the
player is turned off.
y if you press “CLOCK” on state of the unit
turned off, you can see state in order of
“CLOCK” and “TIMER”.
XA146-F0P-AAUSLL-ENG.indd 14
11. 12. 02
1:52
Operating
Advanced Operations
To
Playing the iPod
You can enjoy the sound with your iPod. For details
about iPod, refer to the iPod User Guide.
1. Connect the iPod firmly.
15
Do this
ON UNIT
ON REMOTE
Pauses or
restart
T
d/M
Skip
/
C/V
Search
Press and hold
/
Press and hold
C/V
Move to the
previous
menu
-
MENU/
REPEAT
PRESET/
-
FOLDER
W/S
Chooses a
item
I
3
Operating
Move to the
desired item
Z ENTER
Compatible iPod
y We recommend installing the latest software
version.
If you turn this unit on, with your ipod
connected or docked it will automatically turn
on and recharging will start.
2. Press FUNC. on the unit or FUNCTION on the
remote control to select iPod function. You can
operate your iPod through an iPod’s display
by using the supplied remote control and also
control on your iPod.
XA146-F0P-AAUSLL-ENG.indd 15
y Made for iPod nano (6th, 5th, 4th, 3rd, 2nd and
1st generation), iPod classic, iPod touch (4th, 3rd,
2nd and 1st generation), iPod 5G, iPhone (4, 3GS,
3 G), iPod mini.
For some models, the unit may not operate
depending on the firmware version.
y Depending on your iPod’s software version, you
may not control your iPod from the player.
11. 12. 02
1:52
16
Operating
, Note
y If this unit displays an error message, follow
the message. An error message “ERROR”.
1. Connect the USB device to the unit.
- Your iPod is not connected firmly.
- This unit recognizes your iPod as an
unknown device.
- Your iPod is exceptionally low in power.
2. Select a function by pressing FUNCTION on the
remote control or FUNC. on the unit.
/ The battery needs to be charged.
/ If you charge the battery while iPod
is extremely low in power, it may take
longer to be charged.
All tracks recording - You can record to USB after
stop.
y iPod does not support recording function
when connected.
3
Recording to USB
Operating
y Depending on your iPod’s software version,
it may not be possible to control your iPod
from this unit. We recommed installing the
latest software version.
y If you use an application, make a call, or
send and receive SMS text message, etc. on
iPod touch or iPhone, disconnect it from
iPod dock of this unit and then use it.
y When iPod source is selected, you can not
enjoy audio through the headphone jack.
y If you have a problem with your iPod, please
visit www.apple.com/support/ipod.
One track recording - You can record to USB
after playing a file you want.
Program list recording - After showing the
programmed list, you can record it to USB.
3. Start the recording by pressing REC. on the unit
or X REC on the remote control.
4. To stop recording, press I on the unit or
Z ENTER on the remote control.
To select recording bit rate
and speed
1. Press REC. on the unit or X REC on the remote
control for longer than 3 seconds on the state
of stop.
2. Use C/V on the remote control or
on the unit to select the bit rate.
/
3. Press REC. on the unit or X REC on the remote
control again to select the recording speed.
Listening to music from your
external device
The unit can be used to play the music from many
types of external device.
(Refer to the page 9)
1. Connect the external device to the PORT. IN
connector of the unit.
2. Turn the power on by pressing 1/! (Power).
3. Select the PORTABLE function by pressing
FUNCTION on the remote control or FUNC. on
the unit.
4. Press C/V on the remote control or
on the unit to select a desired
/
recording speed; (Only AUDIO CD)
X1 SPEED
- You can listen to music while recording it.
X2 SPEED
- You can just record the music file.
5. Press REC. on the unit or X REC on the remote
control to finish the setting.
4. Turn the external device and start it playing.
XA146-F0P-AAUSLL-ENG.indd 16
11. 12. 02
1:52
Operating
17
, Note
y When you stop recording during playback,
the file that has been recorded at that time
will be stored.
y Do not remove the USB device or turn
off the unit during USB recording. If not,
an incomplete file may be made and not
deleted on PC.
y If USB recording does not work, the
message like “NO USB”, “ERROR”, “FULL” or “NO
REC” is displayed on the display window.
y Multi card reader device or External HDD
can not be used for USB recording.
y A file is recorded by about 512 Mbyte when
you record for a long term.
3
Operating
y You may not store more than 999 files.
y It’ll be stored as follows.
AUDIO CD
The other source*
* : TUNER, Portable and the like.
The making of unauthorized copies of copyprotected material, including computer
programs, files, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal offense.
This equipment should not be used for such
purposes.
Be responsible
Respect copyrights
XA146-F0P-AAUSLL-ENG.indd 17
11. 12. 02
1:52
18
Troubleshooting
Troubleshooting
Problem
Cause & Correction
y The power cord is not plugged in. Plug in the power cord.
No Power.
y Check whether electricity failed. Check the condition by operating other
electronic devices.
y Check whether you select right function. Press FUNCTION and check the
selected function.
No sound.
y If not, connect speaker cables correctly. Speaker cables connected
correctly.
y An unplayable disc is inserted. Insert a playable disc.
y No disc is inserted. Insert a disc.
The unit does not start
playback.
y The disc is dirty. Clean the disc. (Refer to the 20 page)
y The disc is inserted upside down. Place the disc with the label or printed
side facing upwards.
4
Troubleshooting
y The antenna is positioned or connected poorly. Connect the antenna
securely.
Radio stations cannot
be tuned in properly.
y The signal strength of the radio station is too weak. Tune to the station
manually.
y No stations have been preset or preset stations have been cleared (when
tuning by scanning preset channels). Preset some radio stations, see page
12 for details.
y The remote control is too far from the unit. Operate the remote control
within about 23 ft (7 m).
y There is an obstacle in the path of the remote control and the unit. Remove
The remote control
the obstacle.
does not work properly.
y The batteries in the remote control are exhausted. Replace the batteries
with new ones.
iPod does not work.
XA146-F0P-AAUSLL-ENG.indd 18
y Check whether the player is connected to the unit correctly. Connect it to
the unit correctly.
11. 12. 02
1:52
Appendix
19
Specifications
General
Power requirements
Refer to the main label
Power consumption
Refer to the main label
Dimensions (W x H x D)
230 X 134 X 228 mm
Net Weight (Approx.)
1.9 kg
Operating temperature
0 °C to 40 °C
Operating humidity
5 % to 90 %
Bus Power Supply
USB DC 5 V 0 500 mA
iPod DC 5 V 0 1 A
Inputs/ Outputs
PORT. IN
0.6 Vrms
Tuner
FM Tuning Range
87.5 MHz to 108 MHz
Amplifier
Stereo mode
70 W + 70 W
5
Appendix
CD
Frequency Response
20 Hz to 20 KHz
Signal-to-noise ratio
75 dB
Dynamic range
80 dB
Front Speaker
Type
2 way 2 speaker
Impedance Rated
8Ω
Input Power
70 W
Max. Input Power
140 W
Net Dimensions (W x H x D)
144 X 268 X 191 mm
Net Weight
1.86 kg
y Design and specifications are subject to change without notice.
XA146-F0P-AAUSLL-ENG.indd 19
11. 12. 02
1:52
20 Appendix
Maintenance
Notes on Discs
Handling Discs
Handling the Unit
Never stick paper or tape on the disc.
When shipping the unit
Storing Discs
Please save the original shipping carton and
packing materials. If you need to ship the unit, for
maximum protection, re-pack the unit as it was
originally packed at the factory.
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of heat
and never leave it in a parked car exposed to direct
sunlight.
Keeping the exterior surfaces clean
Cleaning Discs
Do not use volatile liquids such as insecticide spray
near the unit.
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or antistatic spray intended for older vinyl records
Wiping with strong pressure may damage the
surface.
Do not leave rubber or plastic products in contact
with the unit for a long period of time.
Cleaning the unit
5
Appendix
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not
use strong solvents such as alcohol, benzine, or
thinner, as these might damage the surface of the
unit.
Maintaining the Unit
The unit is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty
or worn, the picture quality could be diminished.
For details, please contact your nearest authorized
service center.
XA146-F0P-AAUSLL-ENG.indd 20
Trademarks and
Licenses
iPhone and iPod are trademarks of Apple Inc.,
registered in the U.S. and other countries.
“Made for iPod” and “Made for iPhone” mean
that an electronic accessory has been designed
to connect specifically to iPod or iPhone
respectively, and has been certified by the
developer to meet Apple performance standards.
Apple is not responsible for the operation of
this device or its compliance with safety and
regulatory standards.
Please note that the use of this accessory with
iPod, iPhone may affect wireless performance.
11. 12. 02
1:52
XA146-F0P-AAUSLL-ENG.indd 21
11. 12. 02
1:52
XA146-F0P-AAUSLL-ENG.indd 22
11. 12. 02
1:52
Download PDF