LG | 26LV2530 | LG 26LV2530 Owner’s Manual

OWNER’S MANUAL
LCD TV / LED LCD TV
Please read this manual carefully before operating the
set and retain it for future reference.
P/NO : MFL62864990 (1103-REV03)
Printed in Korea
www.lg.com
2
SAFETY INSTRUCTIONS
Please read these safety precautions carefully before using the product.
yy
In this manual, the illustration may be somewhat different from your product because it is
yy
just example to help the instruction.
warning yyIf you ignore the warning message, you may be seriously injured or there is a
possibility of accident or death.
caution yyIf you ignore the caution message, you may be slightly injured or the product may be damaged.
Precaution in Installing the Product
warning
Keep away from heat sources like electrical
heaters.
- Electrical shock, fire, malfunction or
deformation may occur.
Do not use the product in damp place such
as a bathroom or any place where it is likely
to get wet.
- This may cause a fire or could give an
electric shock.
If you can smell smoke or other odours or hear
a strange sound unplug the power cord and
contact the service center.
- If you continue to use without taking proper
measures, electrical shock or fire can occur.
CAUTION
ENGLISH
ENG
Install the product on a flat and stable place
that has no risk of the product dropping.
- If the product is dropped, you may be injured
or the product may be broken.
Keep the product away from direct sunlight.
- The product can be damaged.
Do not place the product in a built-in
installation such as bookcase or rack.
- Ventilation required.
Electrical Power Related
Precautions
warning
Make sure to connect the power cable to a
properly earthed outlet.
- You may be electrocuted or injured.
Do not touch the power plug with wet hands.
Additionally, it the cord pin is wet or covered
with dust, dry the power plug completely or wipe
dust off.
- You may be electrocuted due to excess
moisture.
During a thunder or lightning storm, unplug the
power cable or signal cable.
- You may be electrocuted or a fire can break
out.
CAUTION
Protect the power cord from physical or
mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits
the appliance.
As long as this unit is connected to the AC wall outlet, it is
not disconnected from the AC power source even if you
turn off this unit by SWITCH.
Precautions WHEN Moving the Product
warning
Make sure to turn off the product.
Make sure to remove all cables before
moving the product.
- You may be electrocuted or the product
can be damaged.
CAUTION
Do not impact the product when moving it.
- You may be electrocuted or the product
can be damaged.
Make the panel face forward and hold it
with both hands to move.
- If you drop the product, the damaged
product can cause electric shock or fire.
Contact your nearest service center for
repair.
Precautions WHEN Using the Product
warning
Do not disassemble, repair or modify the
product at your own discretion.
- Fire or electric shock accident can occur.
- Contact the service center for check,
calibration or repair.
To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or
moisture.
Apparatus shall not be exposed to
dripping or splashing and no objects
filled with liquids, such as vases, shall be
placed on the apparatus.
efer all servicing to qualified service
R
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
IMPORTANT INFORMATION TO PREVENT “IMAGE BURN /
BURN-IN” ON YOUR TELEVISION SCREEN
-W
hen a fixed image (e.g. logos, screen menus, video game,
computer display or teletext pages) is displayed on the
television for an extended period it can become permanently
imprinted on the screen. This phenomenon is known as “image
burn” or “burn-in”. Image burn is not covered under the
manufacturer’s warranty.
- In order to prevent image burn, avoid displaying a fixed
image on your television’s screen for a prolonged period (2 or
more hours for LCD, 1 or more hours for Plasma).
- Image burn can also occur on the letterboxed areas of
your television if you use the 4:3 aspect ratio setting for an
extended period.
ASSEMBLING AND PREPARING
3
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product.
The illustrations in this manual may differ from the actual product and item.
Owner’s manual
Polishing cloth1 (This item is not
included for all models.)
Ferrite core (Depending on model)
(This item is not included for all
models.)
1 Gently wipe the spots on the cabinet with the polishing cloth.
Only 22LK33**
Cable Holder
Protection cover
Only 26/32LK33**, 32/42LK43**, 42/47/55LK53**, 32/37/42/47LK45**
x8
(M4x20)
Screw for assembly
(Except for 47/55LK53**,
47LK45**)
Screw for fixing
Protection cover
Power Cord(This item is not included
for all models.)
ENGLISH
ENG
Remote control and batteries(AAA)
4
ASSEMBLING AND PREPARING
Only 19/22/26LV25**, 22/26LV55** , 26LV30**
x2
x2
M4x12
M4x16
M3x8
(Only 26LV30**)
(Except for 26LV30**)
Screw for assembly
or
x4
DC Adapter
Cable holder
(Depending on model)
(This item is not included for Composite gender cable
(Except for 26LV30**)
all models.)
Only 32LV25**, 32/37/42/47/55LV35**, 32LV30**, 32/42LV34**, 32/42/47/55LW45**
x8
x8
M4 x 14
M4 x 12
(Only 32LV25**) (Except for 32LV25**)
Screw for assembly
(Only 32LV25**, 32/37LV35**,
32LV34**, 32LW45**, 32LV30**)
Cable holder
(Depending on model)
(This item is not included for
all models.)
Screw for fixing
Composite gender cable
(Except for 32LV30**,
32/42LV34**)
ENGLISH
ENG
(Only 32/42/47/55LW45**)
3D Glasses1
(AG-P110, AG-F110)
1 The number of 3D glasses may differ depending on the country.
Caution
Do not use any pirated items to ensure the safety and product life span.
yy
Any damages or injuries by using pirated items are not covered by the warranty.
yy
ASSEMBLING AND PREPARING
5
NOTE
The items supplied with your product may vary depending on the model.
yy
Product specifications or contents of this manual may be changed without prior notice due to
yy
upgrade of product functions.
Image shown may differ from your TV.
yy
How to use the ferrite core (Depending on model)
yy
1 Use the ferrite core to reduce the electromagnetic interference in the PC audio cable. Wind the PC audio cable on the ferrite core thrice. Place the ferrite core close to the TV.
10 mm(+ / - 5 mm)
[to an External device]
[to the TV]
[Cross Section of
Ferrite Core]
[Figure 1]
2 Use the ferrite core to reduce the electromagnetic interference in the power cable.
Wind the power cable on the ferrite core once. Place the ferrite core close to the TV.
[to a wall plug]
[to the TV]
[Cross Section of
Ferrite Core]
[Figure 2]
[to the TV]
[to a wall plug]
[Figure 3]
-If there is one ferrite core, follow as shown in Figure 1.
-If there are two ferrite cores, follow as shown in Figures 1 and 2.
-If there are three ferrite cores, follow as shown in Figures 1 and 3.
[Cross Section of
Ferrite Core]
yy
For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm
thick and 18 mm width.(Except for 22/26/32LK33**, 32/42LK43**, 42/47/55LK53**)
B
A
B
A
*A
*B
10 mm
18 mm
ENGLISH
ENG
3 Use the ferrite core to reduce the electromagnetic interference in the power cable.
Wind the power cable on the ferrite core once. Place the ferrite core close to the TV and a wall plug.
6
ASSEMBLING AND PREPARING
Separate purchase
Separate purchase items can be changed or modified for quality improvement without any notification.
Contact your dealer for buying these items.
These devices only work with compatible LG LED LCD TV or LCD TV.
3D Glasses
(AG-P110, AG-F110 :
Only 3D Models)
ENGLISH
ENG
Parts and buttons
NOTE
yy
TV can be placed in standby mode in order to reduce the power consumption. And TV should be
turned off if it will not be watched for some time, as this will reduce energy consumption.
yy
The energy consumed during use can be significantly reduced if the level of brightness of the
picture is reduced, and this will reduce the overall running cost.
Caution
Do not step on the glass stand or subject it to any impact. It may break, causing possible injury
yy
from fragments of glass, or the TV may fall.
Do not drag the TV. The floor or the product may be damaged.
yy
In case of some model, the thin film on screen is a part of TV. So don't take it off.
ASSEMBLING AND PREPARING
7
Image shown may differ from your TV.
yy
Only 22LK33**
Screen
P
R
H/P
Headphone
Socket
OK
R
USB input
HOME
USB IN
INPUT
Remote control
Speakers
OPTICAL
DIGITAL
(RGB/DVI)
AUDIO IN
AUDIO OUT
1
VIDEO
RGB IN (PC)
L/MONO
1
R
2
AUDIO
RS-232C IN(CONTROL & SERVICE)
Button
/I
ANTENNA/
CABLE IN
Description
Turns the power on or off
INPUT
Changes the input source
HOME
Accesses the main menus, or saves your input and exits the menus
OK
Selects the highlighted menu option or confirms an input
-
+
vP^
Adjusts the volume level
Scrolls through the saved programmes
Connection panel
ENGLISH
ENG
Power Indicator
(Can be adjusted using
the Power Indicator in the OPTION menu.)
8
ASSEMBLING AND PREPARING
Image shown may differ from your TV.
yy
Only 26/32LK33**, 32/42LK43**
Screen
(Only
(Only
26/32LK33**) 32/42LK43**)
USB IN
USB input
P
HDMI IN
IN 3
P
OK
AV (Audio and
Video) IN
H/P
HOME
HOME
INPUT
VIDEO L/MONO AUDIO R
Headphone
Socket
R
OK
AV IN 2
INPUT
Speakers
Remote control
ENGLISH
ENG
Power Indicator
(Can be adjusted using
the Power Indicator in the OPTION menu.)
OPTICAL DIGITAL
AUDIO OUT
AUDIO IN
(RGB/DVI)
1
VIDEO
RGB IN (PC)
L/MONO
1
Button
/I
Connection panel
R
2
ANTENNA/
CABLE IN
AUDIO
RS-232C IN(CONTROL & SERVICE)
Description
Turns the power on or off
INPUT
Changes the input source
HOME
Accesses the main menus, or saves your input and exits the menus
OK
Selects the highlighted menu option or confirms an input
-
+
vP^
Adjusts the volume level
Scrolls through the saved programmes
ASSEMBLING AND PREPARING
9
Image shown may differ from your TV.
yy
Only 42/47/55LK53**
USB input
USB IN
Screen
P
AV (Audio and
Video) IN
IN 3
INPUT
R
Headphone
Socket
OK
HOME
VIDEO L/MONO AUDIO R
HDMI IN
Remote control and intelligent1 sensors
Speakers
AV IN 2
COMPONENT IN
(RGB/DVI)
AUDIO IN
Y
OPTICAL DIGITAL
AUDIO OUT
/I
Connection panel
R
Button
ANTENNA /
CABLE IN
L
1
PR
2
PB
/ DVI IN
AUDIO
RS-232C IN (CONTROL & SERVICE)
VIDEO L/MONO AUDIO R
RGB IN (PC)
VIDEO
AV IN 1
2
1
Description
Turns the power on or off
INPUT
Changes the input source
HOME
Accesses the main menus, or saves your input and exits the menus
OK
Selects the highlighted menu option or confirms an input
-
+
vP^
Adjusts the volume level
Scrolls through the saved programmes
1 Intelligent sensor - Adjusts the image quality corresponding to the surrounding environment.
ENGLISH
ENG
Power Indicator
(Can be adjusted using
the Power Indicator in the OPTION menu.)
10
ASSEMBLING AND PREPARING
Image shown may differ from your TV.
yy
Only 32/37/42/47LK45**
3
4
AV IN 2
USB IN
IN 3
2
Remote control and
intelligent1 sensors
R
IN 3
1
VIDEO L/MONO AUDIO R SPEAKE R OUT
5
Screen
VIDEO L/MONO AUDIO R
USB IN
(Only
32/37/42/47LK455C)
AV IN 2
Power Indicator
(Can be adjusted using
the Power Indicator in the
OPTION menu.)
Speakers
(Except for
32/37/42/47LK455C)
ENGLISH
ENG
No.
Touch buttons2
Description
USB input
2
HDMI IN
3
Headphone Socket
4
AV (Audio and Video)
IN
5
SPEAKER OUT
OPTICAL DIGITAL
AUDIO OUT
AUDIO IN
(RGB/DVI)
1
RGB IN (PC)
VIDEO
1
L/MONO
1
Button
/I
Connection panel
R
2
ANTENNA/
CABLE IN
AUDIO
RS-232C IN(CONTROL & SERVICE)
Description
Turns the power on or off
INPUT
Changes the input source
HOME
Accesses the main menus, or saves your input and exits the menus
OK
Selects the highlighted menu option or confirms an input
-
+
vP^
Adjusts the volume level
Scrolls through the saved programmes
1 Intelligent sensor - Adjusts the image quality corresponding to the surrounding environment.
2Touch Button - You can use the desired button function by touching.
ASSEMBLING AND PREPARING
11
Image shown may differ from your TV.
yy
Only 19/22/26LV25**
USB input
USB IN
Screen
Remote control and
intelligent1 sensors
Headphone
Socket
AV (Audio and
Video) IN
Power Indicator
(Can be adjusted using
the Power Indicator in the
OPTION menu.)
AV IN 2
VIDEO / AUDIO
Speakers
Touch buttons2
Button
vP^
+
-
R
1
L
AUDIO R
2
AUDIO
L/MONO
/ DVI IN
PR
VIDEO
RS-232C IN(CONTROL & SERVICE)
PB
AV IN 1
VIDEO
DC-IN
RGB IN (PC)
ENGLISH
ENG
COMPONENT
IN
(RGB/DVI)
AUDIO IN
Y
OPTICAL
DIGITAL
AUDIO OUT
ANTENNA/
CABLE IN
Description
Scrolls through the saved programmes
Adjusts the volume level
OK
Selects the highlighted menu option or confirms an input
HOME
Accesses the main menus, or saves your input and exits the menus
INPUT
Changes the input source
/I
Connection panel
Turns the power on or off
1 Intelligent sensor - Adjusts the image quality corresponding to the surrounding environment.
2Touch Button - You can use the desired button function by touching.
12
ASSEMBLING AND PREPARING
Image shown may differ from your TV.
yy
Only 32LV25**, 32/37/42/47/55LV35**, 32/42LV34**, 32/42/47/55LW45**
(Only
32/42LV34**)
P
(Only
32/42LV34**)
USB IN
USB IN
USB input
Screen
OK
HOME
HDMI IN
IN 3
INPUT
AV IN 2
AV (Audio and
Video) IN
VIDEO / AUDIO
Headphone
Socket
Power Indicator
(Can be adjusted using
the Power Indicator in the
OPTION menu.)
Speakers
(Except for
32/42LV34**)
Remote control and
intelligent1 sensors
Touch buttons2
(Except for
32/42LV34**)
ENGLISH
ENG
OPTICAL
DIGITAL
AUDIO OUT
(RGB/DVI)
AUDIO IN
1
VIDEO
RGB IN (PC)
L/MONO
1
Connection panel
R
2
ANTENNA/
CABLE IN
AUDIO
RS-232C IN(CONTROL & SERVICE)
2
Button
vP^
+
-
1
Description
Scrolls through the saved programmes
Adjusts the volume level
OK
Selects the highlighted menu option or confirms an input
HOME
Accesses the main menus, or saves your input and exits the menus
INPUT
Changes the input source
/I
Turns the power on or off
1 Intelligent sensor - Adjusts the image quality corresponding to the surrounding environment.
2Touch Button - You can use the desired button function by touching.
ASSEMBLING AND PREPARING
13
Image shown may differ from your TV.
yy
Only 22/26LV55**
USB input
USB IN
Screen
Remote control and
intelligent1 sensors
Headphone
Socket
AV (Audio and
Video) IN
Power Indicator
(Can be adjusted using
the Power Indicator in the
OPTION menu.)
AV IN 2
VIDEO / AUDIO
Speakers
Touch buttons2
AUDIO IN
(RGB/DVI)
OPTICAL
DIGITAL
ENGLISH
ENG
DC-IN
AUDIO OUT
VIDEO
RGB IN (PC)
L/MONO
RS-232C IN
(CONTROL & SERVICE)
AUDIO
1
ANTENNA/
CABLE IN
R
2
Connection panel
Button
Description
Scrolls through the saved programmes
Adjusts the volume level
Selects the highlighted menu option or confirms an input
Accesses the main menus, or saves your input and exits the menus
Changes the input source
/I
Turns the power on or off
1 Intelligent sensor - Adjusts the image quality corresponding to the surrounding environment.
2Touch Button - You can use the desired button function by touching.
14
ASSEMBLING AND PREPARING
Image shown may differ from your TV.
yy
Only 26/32LV30**
Speakers
Screen
OK
USB input
USB IN
R
HOME INPUT
IN 3
HDMI IN
Remote control and intelligent1 sensors
(Except for
32LV30**)
OPTICAL
DIGITAL
Power Indicator
(Can be adjusted using
the Power Indicator in the OPTION menu.)
AUDIO IN
(RGB/DVI)
AUDIO OUT
ENGLISH
ENG
DC-IN
RGB IN (PC)
VIDEO
1
AUDIO R
2
L/MONO
RS-232C IN
(CONTROL & SERVICE)
Button
vP^
+
-
ANTENNA/
CABLE IN
Description
Scrolls through the saved programmes
Adjusts the volume level
OK
Selects the highlighted menu option or confirms an input
HOME
Accesses the main menus, or saves your input and exits the menus
INPUT
Changes the input source
/I
Connection panel
Turns the power on or off
1 Intelligent sensor - Adjusts the image quality corresponding to the surrounding environment.
ASSEMBLING AND PREPARING
Additional information
Viewing the owner’s manual
The owner’s manual in PDF file format is supplied
on the enclosed CD. Install the Adobe Acrobat
Reader to view the owner’s manual on your PC.
1 Insert the supplied CD.
The web page appears automatically.
2Click Owner’s Manual on the web page.
3 View the owner’s manual.
NOTE
If the web page does not appear
automatically, access My computer and then
click LG and index.htm to view the owner’s
manual.
15
Lifting and moving the TV
When moving or lifting the TV, read the following to
prevent the TV from being scratched or damaged
and for safe transportation regardless of its type
and size.
Caution
Avoid touching the screen at all times, as
yy
this may result in damage on the screen
or some of the pixels used to create
images.
It is recommended to move the TV in the box
yy
or packing material that the TV originally came
in.
Before moving or lifting the TV, disconnect the
yy
power cord and all cables.
When holding the TV, the screen should face
yy
away from you to avoid damage.
ENGLISH
ENG
Hold the top and bottom of the TV frame firmly.
yy
Make sure not to hold the transparent part,
speaker, or speaker grill area.
When transporting a large TV, there should be
yy
at least 2 people.
When transporting the TV by hand, hold the
yy
TV as shown in the following illustration.
When transporting the TV, do not expose the
yy
TV to jolts or excessive vibration.
When transporting the TV, keep the TV
yy
upright, never turn the TV on its side or tilt
towards the left or right.
16
ASSEMBLING AND PREPARING
Setting up the TV
Only 26/32LK33**, 32/42LK43**, 42/47/55LK53**
Image shown may differ from your TV.
yy
Put your TV on a pedestal stand and mount the TV
on a table or wall.
1Lay the TV with the screen side down on a flat
Attaching the stand
Only 22LK33**
1Lay the TV with the screen side down on a flat
surface.
Caution
Lay a foam mat or soft protective cloth
yy
on the surface to protect the screen from
damage.
surface.
Caution
Lay a foam mat or soft protective cloth
yy
on the surface to protect the screen from
damage.
2Assemble the parts of the Stand Body with the
Stand Base of the TV.
Stand Body
2 Assemble the TV as shown.
Stand Base
ENGLISH
ENG
3Secure the TV and the stand with the 4 screws.
Caution
yy
Tighten the screws firmly to prevent
the TV from tilting forward. Do not over
tighten.
Caution
yy
Tighten the screws firmly to prevent
the TV from tilting forward. Do not over
tighten.
ASSEMBLING AND PREPARING
17
Only 32/37/42/47LK45**
Only 19/22/26LV25**, 22/26LV55**
1Lay the TV with the screen side down on a flat
1Lay the TV with the screen side down on a flat
surface.
Caution
Lay a foam mat or soft protective cloth
yy
on the surface to protect the screen from
damage.
2Assemble the parts of the Stand Body with the
Stand Base of the TV.
surface.
Caution
Lay a foam mat or soft protective cloth
yy
on the surface to protect the screen from
damage.
2Assemble the parts of the Stand Body with the
Stand Base of the TV.
Stand Body
Stand Base
3Secure the TV and the stand with the 4 screws.
Caution
yy
Tighten the screws firmly to prevent
the TV from tilting forward. Do not over
tighten.
Caution
yy
Tighten the screws firmly to prevent
the TV from tilting forward. Do not over
tighten.
ENGLISH
ENG
3Secure the TV and the stand with the 2 screws.
18
ASSEMBLING AND PREPARING
Only 32LV25**
1Lay the TV with the screen side down on a flat
surface.
Only 32/37/42/47/55LV35**, 32LV30**,
32/42LV34**, 32/42/47/55LW45**
1Lay the TV with the screen side down on a flat
surface.
Caution
Caution
Lay a foam mat or soft protective cloth
yy
on the surface to protect the screen from
damage.
2Assemble the parts of the Stand Body with the
Lay a foam mat or soft protective cloth
yy
on the surface to protect the screen from
damage.
2Assemble the parts of the Stand Body with the
Stand Base of the TV.
Stand Base of the TV.
Stand Body
Stand Body
Except for
32LV30**
Stand Base
Stand Base
ENGLISH
ENG
3Secure the TV and the stand with the 4 screws.
Stand Body
Only
32LV30**
Stand Base
3Secure the TV and the stand with the 4 screws.
Except for
32LV30**
Caution
yy
Tighten the screws firmly to prevent
the TV from tilting forward. Do not over
tighten.
Only
32LV30**
Caution
yy
Tighten the screws firmly to prevent
the TV from tilting forward. Do not over
tighten.
ASSEMBLING AND PREPARING
19
Not using the Desk Type Stand
Only 26LV30**
1Lay the TV with the screen side down on a flat
surface.
Image shown may differ from your TV.
yy
Only 26/32LK33**, 32/42LK43**,
32/37/42/47LK45**, 42/47/55LK53**
Caution
Lay a foam mat or soft protective cloth
yy
on the surface to protect the screen from
damage.
1 Push the supplied protection cover into the
opening at the bottom of the TV until clicking
sound.
2Assemble the parts of the Stand Body with the
Stand Base of the TV.
Stand Body
Stand Base
(M3x8)
Only 22LK33**
1Lay the TV with the screen side down on a flat
surface.
2Remove the 2 screws and pull the stand away
from the TV.
(M4x12)
Caution
yy
Tighten the screws firmly to prevent
the TV from tilting forward. Do not over
tighten.
3 Push the supplied protection cover into the
opening at the bottom of the TV until it locks in
place.
This will protect the opening from accumulating
dust and dirt.
Protection cover
ENGLISH
ENG
3Secure the TV and the stand with the 2 screws.
Protection cover
20
ASSEMBLING AND PREPARING
Mounting on a table
Securing the TV to a table
Image shown may differ from your TV.
yy
1Lift and tilt the TV into its upright position on a
table.
-Leave a 10 cm (minimum) space from the
wall for proper ventilation.
Only 26/32LK33**, 32/42LK43**,
42LK53**,32/37/42LK45**, 32LV25**, 32/37LV35**,
32LV34**, 32LW45**, 32LV30**
Fix the TV to a table to prevent from tilting forward,
damage, and potential injury.
Mount the TV on a table, and then insert and
tighten the supplied screw on the rear of the stand.
10 cm
10 cm
Image shown may differ from your TV.
yy
This feature is not available for all models.
yy
10 cm
10 cm
2Connect the power cord to a wall outlet.
ENGLISH
ENG
warning
To prevent TV from falling over, the TV
yy
should be securely attached to the floor/
wall per installation instructions. Tipping,
shaking, or rocking the TV may cause
injury.
Caution
yy
Do not place the TV near or on sources
of heat, as this may result in fire or other
damage.
NOTE
(Except for 22LK33**, 19/22/26LV25**,
22/26LV55**, 26LV30**)
Swivel 20 degrees to the left or right and
adjust the angle of the TV to suit your view.
20
20
ASSEMBLING AND PREPARING
Securing the TV to a wall
Image shown may differ from your TV.
yy
This feature is not available for all models.
yy
21
Using the Kensington security system
Image shown may differ from your TV.
yy
This feature is not available for all models.
yy
The Kensington security system connector is
located at the rear of the TV. For more information
of installation and using, refer to the manual
provided with the Kensington security system or
visit http://www.kensington.com.
Connect the Kensington security system cable
between the TV and a table.
1 Insert and tighten the eye-bolts, or TV brackets
and bolts on the back of the TV.
ENGLISH
ENG
-If there are bolts inserted at the eye-bolts
position, remove the bolts first.
2 Mount the wall brackets with the bolts to the
wall.
Match the location of the wall bracket and the
eye-bolts on the rear of the TV.
3Connect the eye-bolts and wall brackets tightly
with a sturdy rope.
Make sure to keep the rope horizontal with the
flat surface.
Caution
Make sure that children do not climb on
yy
or hang on the TV.
Mounting on a wall
Attach a wall mount bracket at the rear of the TV
carefully and install the wall mount bracket on a
solid wall perpendicular to the floor. When you
attach the TV to other building materials, please
contact qualified personnel.
LG recommends that wall mounting be performed
by a qualified professional installer.
NOTE
Use a platform or cabinet that is strong
yy
and large enough to support the TV
securely.
10 cm
10 cm
10 cm
10 cm
22
ASSEMBLING AND PREPARING
Separate purchase(Wall Mounting Bracket)
Make sure to use screws and wall mount
bracket that meet the VESA standard. Standard
dimensions for the wall mount kits are described in
the following table.
Model
22LK33**
19/22/26LV25**
22/26LV55**
26LV30**
26/32LK33**
32LK43**
32LK45**
32LV25**
32LV35**
32LV30**
32LV34**
32LW45**
VESA (A x B)
100 x 100
200 x 100
Standard screw
M4
M4
Number of screws 4
4
Wall mount
LSW100B, LSW100BG
bracket
Model
ENGLISH
ENG
42LK43**
37/42/47LK45**
42/47LK53**
37LV35**
VESA (A x B)
200 x 200
Standard screw
M6
Number of screws 4
Wall mount
LSW200B,
bracket
LSW200BG
Model
VESA (A x B)
Standard screw
Number of screws
Wall mount
bracket
42LV34**
400 x 400
M6
4
LSW400BX,
LSW400BXG
42/47/55LV35**
42/47/55LW45**
55LK53**
400 x 400
M6
4
LSW400B,
LSW400BG
Caution
Disconnect the power first, and then
yy
move or install the TV. Otherwise electric
shock may occur.
If you install the TV on a ceiling or slanted
yy
wall, it may fall and result in severe injury.
Use an authorized LG wall mount bracket
and contact the local dealer or qualified
personnel.
Do not over tighten the screws as this
yy
may cause damage to the TV and void
your warranty.
Use the screws and wall mount bracket yy
that meet the VESA standard. Any
damages or injuries by misuse or using
an improper accessory are not covered
by the warranty.
NOTE
Use the screws that are listed on the
yy
VESA standard screw specifications.
The wall mount kit includes an installation
yy
manual and necessary parts.
The length of screws may differ
yy
depending on the wall mount. Make sure
to use the proper length.
For more information, refer to the manual
yy
supplied with the wall mount bracket.
ASSEMBLING AND PREPARING
Tidying cables
23
NOTE
Image shown may differ from your TV.
yy
Only 22LK33**, 19/22/26LV25**, 22/26LV55**
1After connecting the cables as necessary,
Do not move the TV by holding the
yy
cable management clip, as the cable
management clip may break, and injuries
and damage to the TV may occur.
install Cable Holder as shown and bundle the
cables.
Only 32LV25**, 32/37/42/47/55LV35**, 32LV30**,
32/42LV34**, 32/42/47/55LW45**
1 Gather and bind the cables with the Cable
Holder on the TV back cover.
Cable Holder
Only 26LV30**
1After connecting the cables as necessary,
ENGLISH
ENG
install Cable Holder as shown and bundle the
cables.
or
Cable Holder
Cable holder
Only 26/32LK33**, 32/42LK43**,
32/37/42/47LK45**, 42/47/55LK53**
1Gather and bind the cables with the cable
management clip.
2 Fix the cable management clip firmly to the TV.
Cable Holder
Cable Management Clip
24
ASSEMBLING AND PREPARING
Positioning your display
Image shown may differ from your TV.
yy
Only 22LK33**
Adjust the position of the panel in various ways for
maximum comfort.
• Tilt range
12
0
0
3
ENGLISH
ENG
Connection of TV
Image shown may differ from your TV.
yy
Only 19/22/26LV25**, 22/26LV55**, 26LV30**
DC Adapter
1 Connect the antenna cable to the antenna
input port on the TV.
2Connect the DC adapter plug to the power
input jack on the TV.
3 Connect the power cord to the DC adapter first,
then plug the power cord into the wall power
outlet.
REMOTE CONTROL
25
REMOTE CONTROL
The descriptions in this manual are based on the buttons on the remote control.
Please read this manual carefully and use the TV correctly.
To replace batteries, open the battery cover, replace batteries (1.5 V AAA)
matching and ends to the label inside the compartment, and close the
battery cover. Be sure to point the remote control toward the remote control sensor
on the TV.
To remove the batteries, perform the installation actions in reverse.
Caution
Do not mix old and new batteries, as this may damage the remote control.
yy
Image shown may differ from your TV.
yy
In Analogue TV and in some countries, some remote control keys may not work.
yy
ENERGY
AV MODE
INPUT
ENERGY
AV MODE
INPUT
TV/
RAD
TV/
RAD
SAVING
SAVING
1
2
3
1
2
3
4
5
6
4
5
6
7
8
9
7
8
9
LIST
0
Q.VIEW
LIST
0
Q.VIEW
MARK
MARK
FAV
RATIO
FAV
P
A
G
E
P
RATIO
MUTE
GUIDE Home
Q.MENU
OK
BACK INFO
Q.MENU
OK
EXIT
BACK INFO
EXIT
Turns the TV on or off.
AV MODE
Selects an AV mode.
INPUT
Changes the input source; Turns the TV on.
TV/RAD
Selects Radio, TV and DTV programme.
Number buttons
Enters numbers.
LIST
Accesses the saved programme list.
Q.VIEW
Returns to the previously viewed programme.
+MARK
Adjusts the volume level.
FAV
Accesses your favourite programme list
RATIO
Resizes an image.
Adjusts the brightness of the screen to reduce energy consumption
Selects a menu or option.
3D (Only 3D Models) Used for viewing 3D video.
AD
or
ENERGY
AV MODE
INPUT
TV/
RAD
SAVING
1
2
3
4
5
6
7
8
9
LIST
0
Q.VIEW
MARK
FAV
3D
P
MUTE
GUIDE Home
Q.MENU
OK
BACK INFO
EXIT
3D SETTING
RATIO
P
A
G
E
MUTE
Mutes all sounds.
P
PAGE
Scrolls through the saved programmes.
GUIDE
Shows programme guide.
HOME
Accesses the main menus, or saves your input and exit the menus.
Q. MENU
Navigation buttons
(up/down/left/right)
OK
Accesses the quick menus
Scrolls through menus or options.
BACK
Returns to the previous level.
INFO
Views the information of the current programme the screen.
EXIT
Clears all on-screen displays and return to TV viewing.
Moves to the previous or next screen.
Selects menus or options and confirms your input.
Coloured buttons
These buttons are used for teletext (on TELETEXT models only),
Programme edit.
3D SETTING(Only 3D Use this to view 3D video.
Models)
TELETEXT BUTTONS These buttons are used for teletext.
For further details, see the ‘Teletext’ section.
SUBTITLE
Recalls your preferred subtitle in digital mode.
Control buttons
)
(
SIMPLINK
Controls the MY MEDIA menus, or the SIMPLINK compatible devices
(USB,SIMPLINK).
Accesses the AV devices connected to the TV; Opens the SIMPLINK menu.
AD(Only 22/26LV55**) Switches the Audio Description On or Off.
ENGLISH
ENG
GUIDE Home
P
MUTE
P
A
G
E
(POWER)
ENERGY SAVING
26
WATCHING TV
WATCHING TV
Connecting an antenna
Connect an antenna to watch TV while referring to
the following.
To prevent damage do not connect to the mains
outlet until all connections are made between the
devices.
Connect the TV to a wall antenna socket with an
RF cable (75 Ω).
your TV settings according to your preferences.
Language

Mode Setting

Power Indicator

Country

Time Zone

NOTE
Auto Tuning
ENGLISH
ENG
Use a signal splitter to use more than 2
yy
TVs.
If the image quality is poor, install a signal
yy
amplifier properly to improve the image
quality.
If the image quality is poor with an
yy
antenna connected, aim the antenna to
the correct direction.
An antenna cable and converter are not
yy
supplied.
Turning the TV on for the first
time
When you turn the TV on for the first time, the
Initial setting screen appears. Select a language
and customize the basic settings.
1Connect the power cord to a power outlet.
2 In Standby mode, press
3 Follow the on-screen instructions to customize
(POWER) to turn the
TV on.
The Initial setting screen appears if you turn
the TV on for the first time.
NOTE
You can also access Factory Reset by
yy
accessing OPTION in the main menus.
Selects a language to display.
(Except for Australia, New
Zealand, Singapore, South
Africa),
Selects Home Use for the
Home environment.
Sets the power indicator.
(When you select Home Use
from the Mode Setting - only
LED LCD TV)
Selects a country to display.
(Only Australia, New Zealand)
Selects a Time Zone to
display.(Only Australia)
Scans and saves available
channels automatically.
NOTE
DTV mode control buttons may not
yy
function based on country broadcasting
circumstances. (Only DTV)
In country that Digital broadcasting
yy
regulation isn’t fixed, some DTV function
may not work depending on digital
broadcasting circumstances. (Only DTV)
4When the basic settings are complete,
press OK.
NOTE
yy
If you do not complete the Initial setting, it
will appear whenever the TV turns on.
yy
Disconnect the power cord from the
power outlet when you do not use the TV
for a long period of time.
5To turn the TV off, press
(POWER) .
MAKING CONNECTIONS
27
MAKING CONNECTIONS
Connect various external devices to the TV and switch input modes to select an external device. For more
information on external device’s connection, refer to the manual provided with each device.
Available external devices are: HD receivers, DVD players, VCRs, audio systems, USB storage devices,
PC, gaming devices, and other external devices.
NOTE
The external device connection may differ from the model.
yy
Connect external devices to the TV regardless of the order of the TV port.
yy
Connecting your Unit
yyImage shown may differ from your TV
To connect an additional equipment, see the External equipment Setup section in CD Manual.
yy
DVD/STB back
2
DVD/STB
Power Cord
2
OPTICAL
DIGITAL
AUDIO OUT
(RGB/DVI)
AUDIO IN
RGB IN (PC)
1
R
L
R
2
ANTENNA/
CABLE IN
AUDIO
R
AV IN 3
L/MONO
RS-232C IN(CONTROL & SERVICE)
AUDIO
VCR Connection
VIDEO
L/MONO
2
ANTENNA/
CABLE IN
1
VIDEO
VIDEO
VCR back
1
2
1
1
Antenna
Connection
ENGLISH
ENG
or
IN 3 USB IN
3
28
3D IMAGING
3D Imaging
(Only32/42/47/55LW45*)
3D Models)
(Only
3D Technology
This TV can display in 3D via 3D broadcasting or
when the TV is connected to a compatible device,
such as a Blu-ray 3D Player. You need such a
device to watch the TV in 3D. The 3D TV displays
two separate pictures formatted for each eye. The
viewer needs to wear 3D glasses in order to see
these images in 3D format.
WARNING
ENGLISH
ENG
yy
When watching 3D images, you should
maintain a distance of at least twice the
screen width, and you should also be
able to see all of the screen at eye level.
yy
If you watch the 3D imaging too closely or
for a long period of time, it may harm your
eyesight.
yy
Watching the TV or playing video games
that incorporate 3D imaging with the 3D glasses for a long period of time can
cause drowsiness, headaches or fatigue
to you and/or your eyes. If you have a
headache, or otherwise feel fatigued or
drowsy, stop watching the TV and have
a rest.
yy
Pregnant woman, seniors, persons with
heart problems or persons who experience frequent drowsiness should refrain
from watching 3D TV.
yy
Some 3D imaging may cause you to
duck or dodge the image displayed in the
video. Therefore, it is best if you do not
watch 3D TV near fragile objects or near
any objects that can be knocked over
easily.
yy
Please prevent children under the age of
5 from watching 3D TV. It may affect their
vision development.
yy
Warning for photosensitization seizure:
Some viewers may experience a seizure
or epilepsy when exposed to certain factors, including flashing lights or images
in TV or video games. If you or anybody
from your family has a history of epilepsy
or seizure, please consult with your doctor before watching 3D TV.
Also certain symptoms can occur in
unspecified conditions without any previous history. If you experience any of the
following symptoms, immediately stop
watching the 3D imaging and consult a
doctor: dizziness or light-headedness ,
visual transition or altered vision, visual
or facial instability, such as eye or muscle
twitching, unconscious action, convulsion,
loss of conscience, confusion or disorientation, loss of directional sense, cramps,
or nausea. Parents should monitor their
children, including teenagers, for these
symptoms as they may be more sensitive
to the effects of watching 3D TV.
yy
Risk of photosensitization seizure can be
reduced with the following actions.
» Take frequent breaks from watching 3D TV.
» For those who have vision that is different in each eye, they should watch
the TV after taking vision correction
measures.
» Watch the TV so that your eyes are on
the same level as the 3D screen and
refrain from sitting too closely to the TV.
» Do not watch the 3D imaging when
tired or sick, and avoid watching the 3D imaging for a long period of time.
» Do not wear the 3D glasses for any
other purpose than viewing 3D imaging
on a 3D TV. » Some viewers may feel disoriented
after watching 3D TV. Therefore, after
you watch 3D TV, take a moment to regain awareness of your situation before
moving.
3D IMAGING
NOTE
yy
To watch the TV in 3D, you must put on
your 3D glasses. For best results, you
should wear LG Brand 3D glasses. The
3D imaging may not display properly
when using another brand of 3D glasses.
Please see the 3D glasses manual for instructions on how to use the 3D glasses.
yy
After powering on the TV, a few seconds
may be needed for your TV to calibrate.
yy
When watching 2D images, it is recommended to take off the 3D glasses. If you
watch 2D images with the 3D glasses on,
you may see distorted images.
29
When Using 3D Glasses
CAUTION
yy
3D glasses are sold separately. Refer
to the 3D glasses manual for operating
instructions.
yy
Do not use the 3D glasses to replace
your corrective glasses, sunglasses or
protective goggles.
yy
Do not store the 3D glasses in hot or cold
locations.
yy
Do not drop objects onto the 3D glasses.
Do not drop or bend the glasses.
yy
Since the lenses of the 3D glasses are
easily scratched, make sure to clean
only with a soft cloth. Shake off any dust
before using the cloth since the glasses
are easily scratched.
ENGLISH
ENG
30
3D IMAGING
Watching 3D images
Using 3D quick menu option
1 Press 3D SETTING.
Image shown may differ from your TV.
yy
2Use the following options while viewing 3D View 3D mode for 3D images
imaging.
1 Play the 3D video or select 3D channel. (2D to 3D mode is available with all contents)
2 Press 3D and select same type in your displayed picture on the screen. (Select type on "3D Video" tab)
3D Video
2D Video
3D Setting
3D Picture Size ◀
3 Press OK on displayed information window.
Power on your 3D glasses and put them on.
Sit 2 meters from TV to enjoy the best 3D view.
ENGLISH
ENG
Cancel
OK
Put on 3D glasses.
Sit 2 meters from TV to enjoy the best 3D view.
or
OK
Cancel
ꔅ 3D Setting ꔅ 3D Setting ▶
3D Depth 15 ◀
▶
3D Viewpoint 0
◀
▶
3D Picture Balance
◀
Off
▶
3D Picture Correction
◀
Left/Right
▶
OK
* Notice : Turn on the 3D mode automatically for
HDMI input playing the 3D blueray titles.
Just Scan
End 3D video
or
3D Setting
3D Picture Correction
◀
Left/Right
▶
3D Depth 15 ◀
▶
◀
▶
3D Viewpoint 0
OK
End 3D video
4To turn off the 3D mode, press 3D and select
OK.
(Depending on model)
Turn off 3D Mode.
Button
2D mode
OK
Cancel
ꔅ 3D setting
View 2D mode for 3D images
1 Play the 3D video or select 3D channel.
2 Press 3D and select same type in your
displayed picture on the screen. (Select type on "2D Video" tab)
3D Video
2D Video
3To turn off the 2D mode, press 3D and select
OK. Turn off 2D Mode.
3D video
OK
Cancel
Description
Cuts off the outer edges of the
3D Picture Size picture and stretch it to fit the full
screen in 3D mode.
Adjusts the distance between the
object and the background in the
3D Depth
picture to enhance the 3D effect
in 2D to 3D mode.
Brings the picture (including both
the object and background im3D Viewpoint
ages) to the front or back to enhance the 3D effect in 3D mode.
Adjusts the colour and bright3D Picture
ness difference between the right
Balance
and left sides of the picture in 3D mode.
Changes the order of images
3D Picture
in the right and left sides of the
Correction
picture in 3D mode.
3D IMAGING
31
CAUTION
yy
Some menus may not work while watching the TV in 3D.
yyIf used 3D effect on the 2D source, 3D may not work.
yy
The 3D imaging mode is disabled automatically when switching DTV channe ls, input source.
yy
The screen may not be displayed properly if you view 2D DTV images in 3D imaging mode.
yy
3D effect can be seen when 3D Mode is selected appropriately for the 3D input signal supplied to
the TV.
yy
For *mpo files (3D camera files), the 3D imaging mode is enabled automatically.
yy
3D may not be displayed properly for some PC graphics cards.
CAUTION
If you select 3D mode, “Power indicator” is turned off automatically.
yy
While watching 3D imaging, you cannot adjust video/audio settings using the menu.
yy
You can only choose “Standard → Cinema → Game” with the AV MODE button on the remote
yy
control. AV Mode is set as Standard while playing in 3D.
If you’d like to play the BGM using *.mpo file(3D camera file), In advance, the contents path for
yy
BGM should be set on full-sized photo view screen which isn’t *.mpo file(3D camera file).
Picture mode is set as Standard, Energy Saving Off if entering to 3D mode.
yy
ENGLISH
ENG
32
ENTERTAINMENT
ENTERTAINMENT
(Depending on model)
Image shown may differ from your TV.
yy
Connecting USB storage devices
or
ENGLISH
ENG
VIDEO L/MONO AUDIO
AUDIO R
IN 2 USB IN
Connect USB storage devices such as a USB
flash memory, external hard drive to the TV and
use multimedia features.
Connect a USB flash memory or USB memory
card reader to the TV as shown on the following
illustration. The My media screen appears, “POP
UP MENU” will not be displayed while the OSD including Menu, EPG or Schedule list is activated.
To disconnect a USB storage device,
make sure to end the connection properly to prevent damages to the TV or files.
AV IN 2
1 Press Q.MENU to access the quick menus.
2 Press the Navigation buttons to scroll to USB
Device and press OK.
3 Press the Navigation buttons to scroll to Eject
and press OK.
4Disconnect the USB storage device only when
the message says that it is safe to remove.
Caution
yy
Do not turn the TV off or remove a USB
storage device while the USB storage
device is connected to the TV, as this
could result in loss of files or damage to
the USB storage device.
yy
Back up your files saved on a USB storage device frequently, as you may lose
or damage the files and this may be not
covered by the warranty.
Tips for using USB storage devices
yy
Only a USB storage device is recognizable.
yy
If the USB storage device is connected
through a USB hub, the device is not recognizable.
yy
A USB storage device using an automatic
recognition programme may not be recognized.
yy
A USB storage device which uses its own
driver may not be recognized.
yy
The recognition speed of a USB storage
device may depend on each device.
yy
Please do not turn off the TV or unplug the
USB device when the connected USB storage device is working. When such device is
suddenly separated or unplugged, the stored
files or the USB storage device may be damaged.
yy
Please do not connect the USB storage
device which was artificially manoeuvred on
the PC. The device may cause the product to
malfunction or fail to be played. Never forget
to use only a USB storage device which has
normal music files, image files or movie files.
yy
Please use only a USB storage device which
was formatted as a FAT32 file system, NTFS file system provided with the Windows operating system. In case of a storage device
formatted as a different utility programme
which is not supported by Windows, it may
not be recognized.
yy
Please connect power to a USB storage
device(over 0.5 A) which requires an external
power supply. If not, the device may not be
recognized.
yy
Please connect a USB storage device with
the cable offered by the device maker.
yy
Some USB storage devices may not be supported or operated smoothly.
yy
File alignment method of USB storage
device is similar to Window XP and filename
can recognize up to 100 English characters.
yy
Be sure to back up important files since data
stored in a USB memory device may be
damaged. We will not be responsible for any
data loss.
yy
If the USB HDD does not have an external
power source, the USB device may not be
detected. So be sure to connect the external
power source.
- Please use a power adaptor for an external
33
ENTERTAINMENT
Browsing files
Access the photo, music, or movie lists and browse
files.
1Connect a USB storage device.
2 Press Home to scroll to main menus.
3 Press the Navigation buttons to scroll to My
Media and press OK.
4 Press Navigation buttons to scroll to PHOTO
LIST, MUSIC LIST, or MOVIE LIST and press
OK.
Movie List
Photo List
Music List
2
1
Page 1/1
Photo List
USB External
001
002
010
011
Drive1
003
004
005
006
012
013
014
015
Move
To Music List
Page 1/1
Change Numbers
View
007
P
008
Page Change
Mark Mode
009
4
5
MARK Mark
Exit
3
No.
Description
1
Moves to upper level folder
2
Current page/Total pages
3
4
5
Buttom
Green
button
Yellow
button
Blue
button
Corresponding buttons on the
remote control
Current page/ total pages of
contents under the folder
focused on 1
Contents under the folder
focused on 1
Description
Repeatedly, press the GREEN button to
converted to Photo List->Music List,
Music List->Movie List or Movie List>Photo List.
A method to view in 5 large thumbnail or
simple list.
Convert to Mark Mode.
ENGLISH
ENG
power source. We do not guarantee an USB
cable for an external power source.
yy
If your USB memory device has multiple
partitions, or if you use a USB multi-card
reader, you can use up to 4 partitions or USB
memory devices.
yy
If a USB memory device is connected to a
USB multi-card reader, its volume data may
not be detected.
yy
If the USB memory device does not work
properly, disconnect and reconnect it.
yy
How fast a USB memory device is detected
differs from device to device.
yy
If the USB is connected in Standby Mode,
specific hard disk will automatically be
loaded when the TV is turned on.
yy
The recommended capacity is 1 TB or less
for a USB external hard disk and 32 GB or
less for USB memory.
yy
Any device with more than the recommended
capacity may not work properly.
yy
If a USB external hard disk with a “Energy
Saving” function does not work, turn the
hard disk off and on again to make it work
properly.
yy
USB storage devices below USB 2.0 are
supported as well. But they may not work
properly in the movie list.
yy
Maximum of 999 folders or files can be recognized under one folder.
yy
The file arrangement of the USB storage
device is similar to that of Windows XP and
supports up to 100 alphabetical characters.
yy
If there are a lot of folders or files all within
one folder, the device may not be able to
access these properly.
34
TROUBLESHOOTING
TROUBLESHOOTING
General
Problem
Resolution
Cannot control the TV with the
remote control.
yyCheck the remote control sensor on the product and try again.
yyCheck if there is any obstacle between the product and the remote control.
yyCheck if the batteries are still working and properly installed ( to ,
to ).
yyCheck if the appropriate input mode such as TV or VCR is set for using the
remote control.
No image display and no sound is
produced.
yyCheck if the product is turned on.
yyCheck if the power cord is connected to a wall outlet.
yyCheck if there is a problem in the wall outlet by connecting other products.
Image appears slowly when the TV
turns on.
yyThe image is muted during the product start up process. This is normal. If the
image does not appear in a few minutes, unplug the TV for 30 seconds and try
again. If the image still does not appear, contact the authorized service centre
in your local area.
Cannot connect external devices.
yyRefer to the “Connection overview” and connect an external device.
The TV turns off suddenly.
yyCheck the power control settings. The power supply may be interrupted.
yyCheck if the Auto sleep feature is activated in the Time settings. See “Sleep Timer”.
yyIf there is no signal while the TV is on, the TV will turn off automatically after 15
minutes of inactivity.(Except for 22/26/32LK335C-TB, 32/37/42/47/55LV355CTA, 32/37/42/47LK455C-TA)
Audio
Problem
Resolution
ENGLISH
ENG
No sound is produced while images yyPress
+ or - button.
are displaying.
yyCheck if the sound is muted by pressing MUTE.
yyScroll to other channels. There may a problem with the broadcast.
yyCheck if the audio cables are connected properly.
One of the speakers produce
noises or does not produce sound.
yyA change in ambient humidity or temperature may result in an unusual noise
when the product turns on or off.
yyThere is no problem with your product.
Video
Problem
Resolution
An image displays in black and
white or the colour quality is poor.
yyAdjust the colour setting in the Picture menu.
yyKeep a sufficient distance between this product and other electronic products.
yyScroll to other channels. There may a problem with the broadcast.
Horizontal or vertical bars appears
or images blur
yyCheck if there are local interferences such as an electrical appliance or power
tool.
Lines or streaks appear on images
yyCheck the antenna or aim the antenna to the proper direction.
Afterimages (ghosts) appear when
the product turns off
yyPixels may have been damaged from a fixed image displayed for a long time
(image burn). Use a screen saver to prevent the pixel damage on the screen.
The power is on but the screen appears extremely dark.
yyAdjust the brightness and contrast in the Picture menu.
“No Signal” appears on the screen.
yyCheck if the signal cable is connected between the TV and products properly.
yyCheck the selected input source by pressing INPUT.
Black spots appear on the screen.
yySeveral pixels in red, green, white, or black may appear on the screen that can
attribute to the characteristics of the LCD panel. This is normal.
The display offset is wrong.
yyAdjust the position setting in the Picture menu.
yyCheck if the video card resolution and frequency are supported by the product.
If the frequency is out of range, set to the recommended resolution using the
display settings on the external device.
Thin lines appear in the background yyCheck the video cable connections.
of the screen.
Horizontal noises appear or charac- yyAdjust the Phase setting in the Picture menu. ters blur.
Refer to the “SCREEN”.
The reception on some channels
is poor
yyScroll to other channels. There may a problem with the broadcast.
yyThe station signal may be weak. Aim the antenna to the proper direction.
yyCheck if there is local interference such as an electrical appliance or power tool.
SPECIFICATIONS
35
SPECIFICATIONS
22LK33**
22LK330-TA
22LK330-TB
22LK332-TC
22LK335C-TB
22LK330Y-TB
526.0 mm x 377.0 mm x 165 mm
26LK330-TA
26LK330-TB
26LK332-TC
26LK335C-TB
26LK330Y-TB
663.0 mm x 484.0 mm x 207 mm
526.0 mm x 331.0 mm x 65 mm
663.0 mm x 423.0 mm x 79.9 mm
With stand
4.3 kg
7.6 kg
Without stand
4.0 kg
6.5 kg
MODELS
Dimensions With stand
(W x H x D) Without stand
Weight
26LK33**
Power requirement
AC 100-240 V~ 50 / 60 Hz
32LK33**
799.0 mm x 555.0 mm x 207.0 mm
800.0 mm x 509.0 mm x 73.8 mm
799.0 mm x 516 mm x 73.5 mm
With stand
9.6 kg
9.6 kg
Without stand
8.6 kg
MODELS
Power requirement
MODELS
Dimensions With stand
(W x H x D) Without stand
Weight
8.6 kg
AC 100-240 V~ 50 / 60 Hz
42LK43**
42LK430-TA 42LK430-TB
42LK430Y-TB
1023.0 mm x 685.0 mm x 261.0 mm
42LK53**
42LK530-TA 42LK530-TC
42LK530Y-TC
1024.0 mm x 685.0 mm x 261.0 mm
1023.0 mm x 644 mm x 76.6 mm
1024.0 mm x 621.0 mm x 76.8 mm
With stand
15.4 kg
15.5 kg
Without stand
13.7 kg
13.9 kg
Power requirement
AC 100-240 V~ 50 / 60 Hz
47LK53**
47LK530-TA 47LK530-TC
47LK530Y-TC
1137.0 mm x 758.0 mm x 270.0 mm
55LK53**
55LK530-TA
55LK530-TC
55LK530Y-TC
1329.0 mm x 872.0 mm x 330.0 mm
1137.0 mm x 685.0 mm x 76.8 mm
1329.0 mm x 796.0 mm x 96.5 mm
With stand
20.3 kg
33.0 kg
Without stand
18.3 kg
MODELS
Dimensions With stand
(W x H x D) Without stand
Weight
32LK430-TA 32LK430-TB
32LK430Y-TB
Power requirement
29.8 kg
AC 100-240 V~ 50 / 60 Hz
Product specifications shown above may be changed without prior notice due to upgrade of product
functions.
For the power supply and power consumption, refer to the label attached to the product.
ENGLISH
ENG
Dimensions With stand
(W x H x D)
Without stand
Weight
32LK43**
32LK330-TA
32LK330-TB
32LK332-TC
32LK335C-TB
32LK330Y-TB
800.0 mm x 565.0 mm x 207 mm
36
SPECIFICATIONS
32LK45**
37LK45**
Dimensions
(W x H x D)
With stand
32LK450-TA
32LK452-TC
32LK455C-TA 32LK450Y-TA
795.0 mm x 568.0 mm x 207.0 mm
Without stand
795.0 mm x 504.0 mm x 73.5 mm
913.0 mm x 571.0 mm x 77.4 mm
Weight
With stand
9.6 kg
12.8 kg
Without stand
8.5 kg
MODELS
37LK450-TA
37LK452-TC
37LK455C-TA
37LK450Y-TA
913.0 mm x 639.0 mm x 265.0 mm
11.1 kg
Power requirement
AC 100-240 V~ 50 / 60 Hz
42LK45**
47LK45**
Dimensions
(W x H x D)
With stand
42LK450-TA
42LK452-TC
42LK455C-TA
42LK450Y-TA
1019.0 mm x 698.0 mm x 265.0 mm
Without stand
1019.0 mm x 631.0 mm x 76.5 mm
1132.0 mm x 695.0 mm x 76.5 mm
Weight
With stand
16.2 kg
19.0 kg
Without stand
14.5 kg
17.3 kg
MODELS
ENGLISH
ENG
Power requirement
47LK455C-TA
1132.0 mm x 762.0 mm x 265.0 mm
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
19LV25**
Dimensions
(W x H x D)
With stand
455.2 mm X 355 mm X 144.9 mm
22LV25**
22LV2500-TA
22LV2510-TB
22LV2530-TD
22LV251Y-TB
471.2 mm X 365.9 mm X 144.9 mm
Without stand
455.2 mm X 313.1 mm X 40.9 mm
471.2 mm X 315.5 mm X 40.9 mm
Weight
With stand
2.7 kg
3.4 kg
Without stand
2.5 kg
3.2 kg
MODELS
Power requirement
19LV2500-TA 19LV2530-TD
DC 24 V, 1.4 A AC-DC adaptor : 24 V
, 2.5 A /
AC 100-240 V~ 50 / 60 Hz
DC 24 V, 1.7 A AC-DC adaptor : 24 V
, 2.5 A /
AC 100-240 V~ 50 / 60 Hz
Dimensions
(W x H x D)
With stand
26LV25**
26LV2500-TA
26LV2510-TB
26LV2530-TD
26LV251Y-TB
635.6 mm X 475 mm X 169 mm
Without stand
635.6 mm X 413.5 mm X 40.9 mm
777.0 mm X 501.0 mm X 35.4 mm
Weight
With stand
5.4 kg
11.5 kg
Without stand
5.0 kg
10.7 kg
MODELS
Power requirement
DC 24 V, 1.8 A AC-DC adaptor : 24 V
, 2.5 A /
AC 100-240 V~ 50 / 60 Hz
32LV25**
32LV2500-TA
32LV2510-TB
32LV2530-TD 32LV251Y-TB
777.0 mm X 552.0 mm X 216.0 mm
AC 100-240 V~ 50 / 60 Hz
Product specifications shown above may be changed without prior notice due to upgrade of product
functions.
For the power supply and power consumption, refer to the label attached to the product.
SPECIFICATIONS
26LV30**
MODELS
32LV30**
26LV3000-TA
32LV3000-TA
Dimensions
(W x H x D)
With stand
754 mm X 444 mm X 190 mm
885 mm x 526 mm x 205 mm
Without stand
754 mm X 393 mm X 34.0 mm
885 mm x 468 mm x 38.7 mm
Weight
With stand
5.9 kg
10.9 kg
Without stand
5.2 kg
9.6 kg
Power requirement
DC 24 V, 2.1 A
AC-DC adaptor : 24 V
, 3.42 A /
AC 100-240 V~ 50 / 60 Hz
37
AC 100-240 V~ 50 / 60 Hz
ENGLISH
ENG
Product specifications shown above may be changed without prior notice due to upgrade of product
functions.
For the power supply and power consumption, refer to the label attached to the product.
38
SPECIFICATIONS
32LV35**
37LV35**
37LV3500-TA 37LV3500-TB
37LV3510-TB
37LV3530-TD
37LV355C-TA
37LV350Y-TA
888.0 mm x 614.0 mm x 240.0 mm
Dimensions
(W x H x D)
With stand
32LV3500-TA 32LV3500-TB
32LV3510-TB
32LV3530-TD
32LV355C-TA 32LV350Y-TA
764.0 mm x 545.0 mm x 240.0 mm
Without stand
764.0 mm x 484.0 mm x 35.4 mm
888.0 mm x 553.0 mm x 35.4 mm
Weight
With stand
11.4 kg
13.5 kg
Without stand
9.6 kg
11.7 kg
MODELS
Power requirement
AC 100-240 V~ 50 / 60 Hz
42LV35**
47LV35**
47LV3500-TA 47LV3500-TB
47LV3510-TB
47LV3530-TD
47LV355C-TA 47LV350Y-TA
1108.0 mm x 746.0 mm x 256.0 mm
Dimensions
(W x H x D)
With stand
42LV3500-TA 42LV3500-TB
42LV3510-TB
42LV3530-TD
42LV355C-TA
42LV350Y-TA
998.0 mm x 684.0 mm x 256.0 mm
Without stand
998.0 mm x 615.0 mm x 30.4 mm
1108.0 mm x 677.0 mm x 30.4 mm
Weight
With stand
15.5 kg
20.9 kg
Without stand
13.3 kg
18.7 kg
MODELS
ENGLISH
ENG
Power requirement
AC 100-240 V~ 50 / 60 Hz
55LV35**
MODELS
55LV355C-TA
Dimensions
(W x H x D)
With stand
1286.0 mm x 847.0 mm x 338.0 mm
Without stand
1286.0 mm x 778.0 mm x 30.4 mm
Weight
With stand
25.5 kg
Without stand
21.4 kg
Power requirement
MODELS
AC 100-240 V~ 50 / 60 Hz
22LV55**
26LV55**
Dimensions
(W x H x D)
With stand
22LV5500-TB
22LV550Y-TB
530 mm X 388 mm X 145 mm
Without stand
530 mm X 340 mm X 31.3 mm
640.0 mm X 405.0 mm X 31.0 mm
Weight
With stand
3.4 kg
5.05 kg
Without stand
3.2 kg
4.4 kg
Power requirement
DC 24 V, 1.7 A AC-DC adaptor : 24 V
, 2.5 A /
AC 100-240 V~ 50 / 60 Hz
26LV5500-TB
26LV550Y-TB
640.0 mm X 474 mm X 178 mm
DC 24 V, 2.1 A AC-DC adaptor : 24 V
, 2.5 A /
AC 100-240 V~ 50 / 60 Hz
Product specifications shown above may be changed without prior notice due to upgrade of product
functions.
For the power supply and power consumption, refer to the label attached to the product.
SPECIFICATIONS
MODELS
32LV34**
39
42LV34**
Dimensions
(W x H x D)
With stand
32LV3400-TA 32LV340Y-TA
768.0 mm x 555.0 mm x 240.0 mm
Without stand
768.0 mm x 429.0 mm x 45.0 mm
1000.0 mm x 623.0 mm x 43.0 mm
Weight
With stand
11.0 kg
14.8 kg
Without stand
9.3 kg
12.4 kg
Power requirement
MODELS
42LV3400-TA 42LV340Y-TA
1000.0 mm x 694.0 mm x 257.0 mm
AC 100-240 V~ 50 / 60 Hz
32LW45**
42LW45**
Dimensions
(W x H x D)
With stand
32LW4500-TA
32LW450Y-TA
772.0 mm x 549.0 mm x 240.0 mm
Without stand
772.0 mm x 490.0 mm x 34.9 mm
1005.0 mm x 621.0 mm x 29.9 mm
Weight
With stand
10.0 kg
14.5 kg
Without stand
8.2 kg
12.3 kg
Power requirement
MODELS
42LW4500-TA
42LW450Y-TA
1005.0 mm x 688.0 mm x 256.0 mm
AC 100-240 V~ 50 / 60 Hz
55LW45**
55LW4500-TA
55LW450Y-TA
1293.0 mm x 851.0 mm x 338.0 mm
Dimensions
(W x H x D)
With stand
47LW4500-TA 47LW450Y-TA
1115.0 mm x 750.0 mm x 256.0 mm
Without stand
1115.0 mm x 683.0 mm x 29.9 mm
1293.0 mm x 785.0 mm x 29.9 mm
Weight
With stand
20.7 kg
26.2 kg
Without stand
18.5 kg
22.0 kg
Power requirement
AC 100-240 V~ 50 / 60 Hz
Product specifications shown above may be changed without prior notice due to upgrade of product
functions.
For the power supply and power consumption, refer to the label attached to the product.
ENGLISH
ENG
47LW45**
40
SPECIFICATIONS
Operating Temperature
Environment condition
New Zealand, Singapore
Operating Humidity
Storage Temperature
0 °C to 40 °C Less than 80 %
-20 °C to 60 °C
Storage Humidity
Less than 85 %
Television System
Programme Coverage
Australia
Television System
Programme Coverage
Indonesia, Israel
Television System
Programme Coverage
South Africa
Television System
ENGLISH
ENG
Programme Coverage
Veitnam, Malaysia
Television System
Programme Coverage
Iran
Television System
Programme Coverage
Analogue model
Television System
Programme Coverage
External Antenna
Impedance
Digital TV
Analogue TV
DVB-T
PAL/SECAM-B/G/D/K, PAL-I
UHF 21 to 69
DVB-T
VHF 06 to 12,
UHF 27 to 69
DVB-T
UHF 21 to 69
DVB-T
VHF 4 to 11, 13
UHF 21 to 68
DVB-T
VHF 6 to 12,
UHF 21 to 69
DVB-T
VHF 5 to 12,
UHF 21 to 69
-
-
75 Ω
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
PAL B/B
B/B : VHF/UHF 0 to 75, CATV : 2 to 44
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
75 Ω
Product specifications shown above may be changed without prior notice due to upgrade of product
functions.
For the power supply and power consumption, refer to the label attached to the product.
OPEN SOURCE LICENSE
41
Open source software notice
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices
are available for download.
ENGLISH
ENG
An extended Owner’s Manual that contains
information on the advanced features of these
LG TV sets is located on the CD- ROM provided
in an electronic version.
To read these files, you will need to use a
Personal Computer (PC) equipped with a CDROM drive.
Re co rd t h e m o d e l n u m b e r a n d s e r i a l
number of the TV.
Refer to the label on the back cover and
quote this information to your dealer when
requiring any service.
(Only DTV)
Model :
Serial No. :
Trade Mark of the DVB Digital Video
Broadcasting Project (1991 to 1996)
Download PDF