LG | 50PC5D | LG 42PC5D Owner’s Manual

PLASMA TV MODELS
42PC5D*
50PC5D*
Please read this manual carefully before operating
your set. Retain it for future reference.
Record model number and serial number of the set.
Refer to the label on the back cover and quote this
information.
To your dealer when requiring service.
DVB is a registered trademark
of the DVB Project
I D N u m b e r : 4721: 42PC5D
4720: 50PC5D
Ensure that the following accessories are included with your product. If an accessory is missing, please contact
the dealer where you purchased the product.
INPUT
D/A
ACCESSORIES
ACCESSORIES
MODE
TV
POWER
INPUT
VCR
BRIGHT
DVD
SIMPLINK
RATIO TEXT
i
SUBTITLE
INFO
MENU
EXIT
i
GUIDE
LIST
FAV
OK
Q.VIEW
VOL
PR
PAGE
MUTE
1
2
3
4
5
6
7
8
9
I/II
0
SLEEP
SIZE
INDEX
TIME
?
REVEAL
Batteries
Owner’s Manual
■
Remote Control
Power Cord
Lightly wipe any stains or fingerprints on the surface of the
TV with the polishing cloth.
■
Polishing Cloth
Do not use excessive force. This may cause scratching or
discolouration.
Polishing cloth for use on the
screen
1
CONTENTS
CONTENTS
ACCESSORIES
...........................................
1
Input List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Calling Up the Channel List . . . . . . . . . . . . . . . . 39
Input Source Selection . . . . . . . . . . . . . . . . . . . . 40
SIMPLINK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Key Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
PREPARATION
EPG (ELECTRONIC PROGRAMME GUIDE)
Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . 4
Back Panel Information . . . . . . . . . . . . . . . . . . . . .5
Attaching the TV to a Wall . . . . . . . . . . . . . . . . . . 6
Back Cover for Wire Arrangement . . . . . . . . . . . . 7
Desktop Pedestal Installation . . . . . . . . . . . . . . . . 8
Wall Mount: Horizontal Installation . . . . . . . . . . . 8
Antenna Connection . . . . . . . . . . . . . . . . . . . . . . . 9
EXTERNAL EQUIPMENT SETUP
HD Receiver Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Other A/V Source Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
- Screen Setup for PC Mode . . . . . . . . . . . . . . . . . . . . . . . . . 21
AV Output Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Digital Audio Output Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
WATCHING TV / PROGRAMME CONTROL
Remote Control Key Functions . . . . . . . . . . . . . .24
Turning on the TV . . . . . . . . . . . . . . . . . . . . . . . . 26
Initializing Setup . . . . . . . . . . . . . . . . . . . . . . . . . 26
Programme Selection . . . . . . . . . . . . . . . . . . . . . 27
Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . 27
On-Screen Menus Selection and Adjustment . . 28
Factory Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Model Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Auto Programme Tuning . . . . . . . . . . . . . . . . . . .30
Manual Programme Tuning . . . . . . . . . . . . . . . . . 32
Fine Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Assigning a Station Name . . . . . . . . . . . . . . . . . 35
Programme Edit . . . . . . . . . . . . . . . . . . . . . . . . . .36
2
Switch on/off EPG . . . . . . . . . . . . . . . . . . . . . . . 44
Select a programme . . . . . . . . . . . . . . . . . . . . . . 44
Button Function in NOW/NEXT Guide Mode . 45
Button Function in 7 Days Guide Mode . . . . . . 45
Button Function in Extended Description Box . 46
Button Function in Reservation Setting Mode . . 46
PICTURE CONTROL
Picture Size (Aspect Ratio) Control . . . . . . . . . .47
Preset Picture Settings
- Picture Mode - Preset . . . . . . . . . . . . . . . . 48
- Auto Colour Tone Control
(Warm/Medium/Cool) . . . . . . . . . . . . . . . .49
Manual Picture Adjustment
- Picture Mode - User Option . . . . . . . . . . . 50
- Colour Tone - User Option. . . . . . . . . . . . .51
Brightness Adjustment . . . . . . . . . . . . . . . . . . . . . . 52
XD - Picture Improvement Technology . . . . . . . . . . . 53
Advanced - Cinema . . . . . . . . . . . . . . . . . . . . . . . 54
Advanced - Black(Darkness) Level . . . . . . . . . . . 55
Picture Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Image Sticking Minimization(ISM) Method . . . . 57
Low Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Auto Volume Leveler (Auto Volume) . . . . . . . . . 59
Preset Sound Settings - Sound Mode . . . . . . . . 60
Sound Setting Adjustment - User Mode . . . . . . . . 61
Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
TV Speakers On/ Off Setup . . . . . . . . . . . . . . . . 64
I/II
- Stereo/Dual Reception . . . . . . . . . . . . . . . . . 65
- Speaker Sound Output Selection . . . . . . . . 65
Subtitle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
APPENDIX
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . .80
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
CONTENTS
SOUND & LANGUAGE CONTROL
Product Specifications . . . . . . . . . . . . . . . . . . . . 83
Programming the Remote Control . . . . . . . . . . 84
IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
External Control through RS-232C . . . . . . . . . . 89
Open Source License . . . . . . . . . . . . . . . . . . . . . 95
TIME SETTING
Clock Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Auto On/ Off Timer Setting . . . . . . . . . . . . . . . .69
Sleep Timer Setting . . . . . . . . . . . . . . . . . . . . . . .70
Auto Shut-off Setting . . . . . . . . . . . . . . . . . . . . . 71
PARENTAL CONTROL / RATINGS
Set Password & Lock System . . . . . . . . . . . . . . . 72
Programme Blocking . . . . . . . . . . . . . . . . . . . . . . 75
Parental Guidance . . . . . . . . . . . . . . . . . . . . . . . . 76
External Input Blocking . . . . . . . . . . . . . . . . . . . . 77
TELETEXT
Switch On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Simple Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
TOP Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Fastext . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Special Teletext Functions . . . . . . . . . . . . . . . . . 79
After reading this manual, keep it handy for future reference.
3
PREPARATION
FRONT PANEL CONTROLS
PREPARATION
■
■
This is a simplified representation of the front panel. Image shown may differ from your TV.
If your product has a protection film attached, remove the film and then wipe the product with a polishing
cloth.
Power/Standby Indicator
• illuminates red in standby mode.
• illuminates green when the set is switched on.
Remote Control Sensor
INPUT
MENU
INPUT
POWER
4
PR
VOL
OK
INPUT
MENU
MENU
VOL
OK
OK
VOLUME
PR
PROGRAMME
BACK PANEL INFORMATION
PREPARATION
■
This is a simplified representation of the back panel . Image shown may differ from your TV.
USB port
(Service only)
AV IN 3
L/MONO
L/
MONO
VIDEOVIDEO
AUDIO
S-VIDEO
AUDIORR S-VIDEO
L/MONO
SVC Only
AV
V IN 2
S-VIDEO Input
Connect S-Video out from an
S-VIDEO device.
AUDIO/VIDEO Input
Connect audio/video output from
an external device to these jacks.
10
1
2
AV 1
3
RGB IN
HDMI IN
1
2
ANTENNA
IN
ANTENNA
IN
RGB IN
RGB (PC)
DIGITAL AUDIO OUT
AUDIO
(RGB/DVI)
REMOTE
CONTROL IN
COMPONENT IN
VIDEO
AUDIO
6
OPTICAL
PTICAL
VIDEO
VARIABLE AUDIO OUT
HDMI/DVI
IN
AV OUT
HDMI/DVI IN
5
4
AV 2
RS-232C IN
(CONTROL & SERVICE)
COMPONENT IN
2
VIDEO
AUDIO
VIDEO (MONO) AUDIO
7
1
AV IN 1
1
S-VIDEO
AUDIO
8
HDMI/DVI IN
Connect a HDMI signal.
Or DVI(VIDEO)signal to the this port with a
HDMI to DVI cable.
9
7
COMPONENT IN
Connect a component video/audio device to
these jacks.
8
AV (Audio/Video) IN 1
Connect audio/video output from an external
device to these jacks.
S-VIDEO
Connect S-Video out from an S-VIDEO device.
RGB/AUDIO IN
Connect the output from a set top box or PC to
the appropriate input port.
3
RS-232C IN (CONTROL &SERVICE) PORT
Connect to the RS-232C port on a PC.
9
AV OUT
Connect a second TV or monitor.
Remote Control Port
Connect your wired remote control.
10
Power Cord Socket
ANTENNA
For operation
with AC power.
IN
DIGITAL
Caution:
Never
attempt to operate the TV on DC
AUDIO OUT
REMOTE
power. OPTICAL VIDEO
CONTROL IN
RGB IN
5
ANTENNA IN HDMI/DVI IN
RGB (PC)
Connect RF antenna (UHF) to this jack.
6
DIGITAL AUDIO OUT
COMPONENT IN
Connect digital audio from various types of
equipment. Note: In standby mode, these ports
do not work.
VIDEO
AUDIO
(RGB/DVI)
RS-232C IN
(CONTROL & SERVICE)
AUDIO
S-VIDEO VIDEO
(
)
AUDIO
AV IN 1
4
AV OUT
2
5
PREPARATION
ATTACHING THE TV TO A WALL
PREPARATION
Purchase the eye-bolts or TV brackets/bolts to fix the TV to the wall on the market.
Position the TV close to the wall to avoid the possibility of it falling when pushed.
A The instructions shown below are a safer way to set up the TV, which is to fix it to the wall, avoiding the
possibility of it falling forwards if pulled. This will prevent the TV from falling forward and causing injury.
This will also prevent the TV from damage. Ensure that children do not climb or hang from the TV.
A
A
1
2
1
Use the eye-bolts or TV brackets/bolts to fix the product to the wall as shown in the picture.
(If your TV has bolts in the eyebolts, loosen then bolts.)
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
2
Secure the wall brackets with bolts to the wall.
Ensure that both brackets are even.
3
Use a strong cord to secure the TV.
Secure the cord in such a way that it becomes taught when the TV is in position.
3
! NOTE
G
G
G
6
When moving the TV undo the cords first.
Use a platform or cabinet string and large enough to support the size and weight of the TV.
To use the TV safely make sure that the height of the bracket on the wall and on the TV is the same.
BACK COVER FOR WIRE ARRANGEMENT
■
1
Grip the CABLE MANAGEMENT and push the cover upwards.
PREPARATION
Here shown may be somewhat different from your TV.
CABLE MANAGEMENT
2
Connect the cables as necessary.
To connect additional equipment, see the External equipment Setup section of the manual.
3
Reinstall the C A B L E M A N A G E M E N T as shown.
! NOTE
G Do not use the CABLE MANAGEMENT to lift the TV.
- If the TV is dropped, you may be injured or the TV may be damaged.
7
PREPARATION
EARTHING
Power Supply
PREPARATION
Ensure that you connect the earth wire to prevent
possible electric shock. If grounding methods are not
possible, have a qualified electrician install a separate
circuit breaker.
Do not try to earth the TV by connecting it to telephone wires, lightening rods or gas pipes.
Circuit breaker
DESKTOP PEDESTAL INSTALLATION
For adequate ventilation allow a clearance of 4” (10cm) all around the TV .
4 inches
4 inches
4 inches
4 inches
CAUTION
G
Ensure adequate ventilation by following the clearance recommendations.
WALL MOUNT: HORIZONTAL INSTALLATION
For adequate ventilation allow a clearance of 4” (10cm) all around the TV.
Detailed installation instructions are available from your dealer.
4 inches
4 inches
4 inches
4 inches
4 inches
8
■
To prevent damage do not connect to the mains outlet until all connections are made between the devices.
PREPARATION
ANTENNA CONNECTION
Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections.
For optimum picture quality, adjust antenna direction if needed.
Wall
Antenna
Socket
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
ANTENNA
IN
Outdoor
Antenna
(VHF, UHF)
RF Coaxial Wire (75 ohm)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
UHF
Antenna
Signal
Amplifier
ANTENNA
IN
VHF
In poor signal areas, to achieve better picture quality it may be necessary to install a signal amplifier to
the antenna.
■ If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.
■ If the antenna is not installed properly, contact your dealer for assistance.
■
! NOTE
G
The TV will let you know when the analogue, cable, and digital programme scans are complete.
9
EXTERNAL EQUIPMENT SETUP
■
To avoid damaging any equipment, never plug in any power cords until you have finished connecting all equipment.
HD RECEIVER SETUP
RGB IN
RGB (PC)
Connecting with a Component cables
EXTERNAL EQUIPMENT SETUP
1
COMPONENT IN
Connect the video outputs (Y, PB, PR) of the digital set
top box to the COMPONENT IN VIDEO 1 jacks on
the set. Match the jack colours.
(Y = green, PB = blue, and PR = red)
2
Connect the audio output of the digital set-top box to
the COMPONENT IN AUDIO 1 jacks on the set.
3
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
4
Select C o m p o n e n t 1 input source using the INPUT
button on the remote control.
If connected to COMPONENT IN 2 input, select
C o m p o n e n t 2 input source.
Signal
Component 1/2
HDMI/DVI 1, 2, 3
480i
Yes
No
480p
Yes
Yes
576i
Yes
No
576p
Yes
Yes
720p
Yes
Yes
1080i
Yes
Yes
1080p
Yes
Yes
VIDEO
AUDIO
2
1
Y
PB
PR
L
R
RGB IN
RGB (PC)
AUDIO
(RGB/DVI)
COMPONENT IN
10
DIGITAL
AUDIO OUT
IN
DIGITAL
AUDIO OUT
AUDIO
(RGB/DVI)
Connecting with HDMI cable
RGB (PC)
1
Connect the digital set-top box to H D M I / D V I I N 1or 2
jack on the set.
(RGB/DV
HDMI/DVI IN
COMPONENT IN
No separate audio connection is necessary.
AUDIO
2
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
3
Select HDMI1or HDMI2 input source using the INPUT
button on the remote control.
2
1
VIDEO
AUDIO
EXTERNAL EQUIPMENT SETUP
RGB IN
PONENT IN
1
! NOTE
G
G
If the digital set-top box supports Auto HDMI function, the
output resolution of the source device will be automatically
set to 1280x720p.
HDMI-DTV OUTPUT
If the digital set-top box player does not support Auto
HDMI, you need to set the output resolution appropriately.
To get the best picture quality, adjust the output resolution
of the source device to 1280x720p.
11
EXTERNAL EQUIPMENT SETUP
Connecting HDMI to DVI cable
EXTERNAL EQUIPMENT SETUP
1
Connect the DVI output of the digital set-top box to the
H D M I / D V I I N 1or 2 jack on the set.
RGB IN
RGB (PC)
DIGITAL
AUDIO OUT
HDMI/DVI IN
COMPONENT IN
2
Connect the audio output of the digital set-top box to the
A U D I O ( R G B / D V I ) jack on the set.
2
1
VIDEO
3
DIO
4
AUDIO
Turn on the digital set-top box. (Refer to the owner’s manual
for the digital set-top box.)
1
2
Select HDMI1or HDMI2 input source using the I N P U T
button on the remote control.
DVI-DTV OUTPUT
12
AUDIO
(RGB/DVI)
L
R
DVD SETUP
RGB IN
DIGI
AUDIO
RGB (PC)
Connecting Component cables
1
(C
VIDEO
2
Connect the audio outputs of the DVD to the
C O M P O N E N T I N A U D I O 1 jacks on the set.
3
Turn on the DVD player, insert a DVD.
AUDIO
1
4
Select C o m p o n e n t 1 input source using the INPUT
button on the remote control.
If connected to C O M P O N E N T I N 2 input, select
C o m p o n e n t 2 input source.
5
Refer to the DVD player's manual for operating
instructions.
Y
PB
S
EXTERNAL EQUIPMENT SETUP
COMPONENT IN
Connect the video outputs (Y, PB, PR) of the DVD to
the C O M P O N E N T I N V I D E O 1 jacks on the set.
Match the jack colours (Y = green, PB = blue, and PR
= red).
2
PR
L
R
Component Input ports
To achieve better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the TV
Video output ports
on DVD player
Y
PB
PR
Y
PB
PR
Y
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
13
HDMI/DVI IN
RGB IN
DIGITAL
AUDIO OUT
RGB (PC)
EXTERNAL EQUIPMENT SETUP
COMPONENT IN
Connecting with
an S-Video cable
2
Connect the
S-VIDEO output of the DVD to the S-VIDEO
1 (DVI)
input on the set.
VIDEO
AUDIO
EXTERNAL EQUIPMENT SETUP
2
Connect the audio outputs of the DVD to the AUDIO
input jacks on the set.
3
Turn on the DVD player, insert a DVD.
4
Select A V 1 input source using the I N P U T button on the
remote control.
If connected to A V I N 2 input, select A V 2 input
source.
5
Refer to the DVD player's manual for operating instructions.
AV IN 1
1
S-VIDEO
AUDIO
(MONO) AUDIO
VIDEO
1
2
L
S-VIDEO
R
AUDIO
Connecting HDMI cable
RGB IN
1
RGB (PC)
Connect the HDMI output of the DVD to the
H D M I / D V I I N 1or 2 jack on the set.
(R
HDMI/DVI IN
COMPONENT IN
COMPONEN
2
No separate audio connection is necessary.
3
Select HDMI1or HDMI2 input source using the INPUT
button on the remote control.
4
Refer to the DVD player's manual for operating instructions.
2
1
VIDEO
1
! NOTE
G
If the DVD supports Auto HDMI function, the DVD output
resolution will be automatically set to 1280x720p.
G
If the DVD player does not support Auto HDMI, you must
set the output
appropriately.
RGB resolution
IN
DIGITAL
RGB
(PC)
To get the best picture quality, adjust theAUDIO
output
OUT resolution
of the DVD to 1280x720p.
HDMI/DVI IN
COMPONENT IN
14
HDMI-DVD OUTPUT
AUDIO
VIDEO
AUDIO
VIDEO
(
)
AUDIO
VCR SETUP
To avoid picture noise (interference), allow adequate distance between the VCR and TV.
■ If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the
screen. This phenomenon is common to all manufacturers and in consequence the manufacturer’s warranty
does not cover the product bearing this phenomenon.
■
Connecting with an antenna
2
1 (DVI)
ANTENNA
IN
RGB IN
UDIO
GB/DVI)
DIGITAL AUDIO OUT
REMOTE
CONTROL IN
OPTICAL
RS-232C IN
(CONTROL & SERVICE)
COMPONENT
T IN
ANT OUT
S-VIDEO
ANT IN
OUTPUT
SWITCH
VIDEO
L
R
VIDEO
AV OUT
RGB (PC)
1
AUDIO
VIDEO
(MONO) AUDIO
AV IN 1
VIDEO
S-VIDEO
AUDIO
Wall Jack
EXTERNAL EQUIPMENT SETUP
HDMI/DVI IN
2
Antenna
1
Connect the RF antenna out socket of the VCR to the A N T E N N A I N socket on the set.
2
Connect the antenna cable to the RF antenna in socket of the VCR.
3
Set VCR output switch to 3 or 4 and then tune TV to the same programme number.
4
Insert a video tape into the VCR and press P L A Y on the VCR. (Refer to the VCR owner’s manual.)
15
R
RGB (
C
VID
HDMI/DVI IN
RGB IN
DIGITAL
AUDIO OUT
RGB (PC)
EXTERNAL EQUIPMENT SETUP
COMPONENT IN
2
Connecting with an RCA cable
1 (DVI)
VIDEO
1
AUDIO
VIDEO
(MONO) AUDIO
VIDEO jacks between TV and
Connect the AUDIO/V
VCR. Match the jack colours(Video = yellow, Audio Left =
white, and Audio Right = red)
EXTERNAL EQUIPMENT SETUP
2
Insert a video tape into the VCR and press P L A Y on
the VCR. (Refer to the VCR owner’s manual.)
3
Select A V 1 input source using the I N P U T button on
the remote control.
If connected to A V I N 2, select A V 2 input source.
1
VIDEO
! NOTE
G
AV IN 1
S-VIDEO
AUDIO
HDMI/DVI IN
L
R
S-VIDEO
ANT IN
OUTPUT
SWITCH
ANT OUT
RGB IN
DIGITAL
AUDIO OUT
RGB (PC)
If you have a mono VCR, connect the audio cable from the
VCR to the A U D I O L ( M O N O ) jack of the set.
COMPONENT IN
2
Connecting with an S-Video cable
1 (DVI)
VIDEO
1
Connect the S-VIDEO output of the VCR to the S-VIDEO
input on the set.
2
Connect the audio outputs of the VCR to the AUDIO
input RGB
jacksINon the set.
RGB (PC)
Insert a video tape into the VCR and press P L A Y on
the VCR. (Refer to the VCR owner’s manual.)
4
Select A V 1 input source using the INPUT button on
the remote control.
If connected to A V I N 2 input, select A V 2 input
source.
VIDEO (MONO) AUDIO
ANTENNA
IN
2
1
DIGITAL AUDIO OUT
3
HDMI/DVI IN
AUDIO
AV IN 1
S-VIDEO
AUDIO
COMPONENT IN
2
1
VIDEO
S-VIDEO
VIDEO
! NOTE
G
The picture quality is improved; compared to normal
composite (RCA cable) input.
R
ANT IN
OUTPUT
SWITCH
ANT OUT
CAUTION
G
16
L
AUDIO
Do not connect to both Video
and S-Video at the same time. In
the event that you connect both
Video and the S-Video cables,
only the S-Video will work.
OTHER A/V SOURCE SETUP
VIDEO L/MONO
1
Camcorder
VIDEO
L
EXTERNAL EQUIPMENT SETUP
R S-VIDEO
SVC Only
AV IN 2
R
Video Game Set
1
VIDEO jacks between TV and
Connect the AUDIO/V
external equipment. Match the jack colours.(Video = yellow, Audio Left = white,
and Audio Right = red)
2
Select A V 2 input source using the INPUT button on the remote control.
If connected to AV IN1 input, select A V 1 input source.
3
Operate the corresponding external equipment.
17
EXTERNAL EQUIPMENT SETUP
PC SETUP
This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
The TV perceives 1024x768, 60Hz as DTV 720p based on the PC graphic card. If necessary, change the
screen scanning rate for the graphic card accordingly.
ANT
RGB IN
AUDIO
(RGB/DVI)
1
RGB IN
RGB (PC)
2
REMOTE
CONTROL IN
3
Turn on the PC and the set.
4
Select RGB-PC input source using the I N P U T button
on the remote control.
5
Once you select RGB-PC input source using the
INPUT button on the remote control, INPUT button is
also available for this purpose.
1
AUDIO
2
! NOTE
G
18
Check the image on your TV. There may be interference
relating to resolution, vertical pattern, contrast or brightness in
PC mode. If noise is present, change the PC output to
another resolution, change the refresh rate to another rate
or adjust the brightness and contrast on the VIDEO menu
until the picture is clear. If the refresh rate of the PC
graphic card can not be changed, change the PC graphic
card or consult the manufacturer of the PC graphic card.
RGB OUTPUT
OPT
RS-232C IN
(CONTROL & SERVICE)
Connect the PC audio output to the AUDIO
(RGB/DVI) j ack on the set.
VIDEO
AUDIO
DIGITAL
DIG
AUDIO OUT
AUDIO
(RGB/DVI)
COMPONENT IN
COMPONENT IN
VIDEO
DIGITAL
Connect
the RGB output of the PC to the R G B
AUDIO OUT
(P C ) jack on the set.
AUDIO
S-VIDEO
EXTERNAL EQUIPMENT SETUP
Connecting D-sub 15pin cable
VIDEO
Connecting HDMI to DVI cable
Connect the DVI output of the PC to the H D M I / D V I
I N 1 or 2 jack on the set.
(Use the HDMI to DVI cable)
RGB IN
RGB (PC)
AUDIO
(RGB/DVI)
HDMI/DVI IN
COMPONENT IN
2
2
Connect the PC audio output to the AUDIO (RGB/DVI)
jack on the set.
1
VIDEO
3
Turn on the PC and the set.
2
1
4
AUDIO
EXTERNAL EQUIPMENT SETUP
1
Select HDMI1or HDMI2 input source using the INPUT
button on the remote control.
DVI-PC
OUTPUT
L
R
! NOTE
G
If the PC has a DVI output and no HDMI output, a separate audio connection is necessary.
G
If the PC does not support Auto DVI, you need to set the output resolution appropriately.
G
To get the the best picture quality, adjust the PC graphics card to 1024x768, 60Hz(42PC5D*) or
1360x768, 60Hz(50PC5D*).
19
DIG
AUDIO
EXTERNAL EQUIPMENT SETUP
Supported Display Specifications (RGB/HDMI-PC )
Supported Display Specifications (HDMI-DTV)
EXTERNAL EQUIPMENT SETUP
Resolution
Horizontal
Frequency(kHz)
Vertical
Frequency(Hz)
Resolution
Horizontal
Frequency(kHz)
Vertical
Frequency(Hz)
640x480
31.469
37.500
59.940
75.000
720x576p
31.25
50.00
720x400
31.469
70.08
720x480p
31.47
31.50
59.94
60.00
800x600
37.879
46.875
60.317
75.000
1280x720p
37.50
44.96
45.00
50.00
59.94
60.00
1024x768
48.363
56.476
60.023
60.004
70.069
75.029
1920x1080i
33.72
33.75
28.125
59.94
60.00
50.00
1280x768
47.776
59.870
1360x768
47.712
60.015
1366x768
47.13
59.65
26.97
27.00
33.716
33.750
56.25
67.43
67.50
23.976
24.00
29.97
30.00
50.00
59.94
60.00
(execpt 50PC5D*)
1920x1080p
! NOTES
G
G
G
20
Depending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use.
Avoid keeping a fixed image on the screen for prolonged periods of time. The fixed image may become
permanently imprinted on the screen.
The synchronization input form for Horizontal and Vertical frequencies is separate.
Screen Setup for PC mode
Overview
When you change the resolution, select the proper resolution in
present input to see the best picture appearance.
Picture Mode
: User1
Colour Temperature
1
Press the M E N U button and then use D or E button
to select the PICTURE menu.
: Cool
EXTERNAL EQUIPMENT SETUP
When the RGB input, of the set is connected to a PC Output, Select
RGB-PC with using the INPUT button on the remote control.
XD
Advanced
Aspect Ratio
: 16:9
Picture Reset
Screen
2
Press the G button and then use D or E button to
select Screen.
3
Press the G button to enter the screen adjustment
menu.
Picture Mode
Colour Temperature
XD
Advanced
Aspect Ratio
Picture Reset
Screen
G
Selection ( G or ) leads you to
the screen adjustment menu.
21
EXTERNAL EQUIPMENT SETUP
Adjustment for screen Resolution, Position, Clock, Phase
EXTERNAL EQUIPMENT SETUP
1
Use D or E button to select R e s o l u t i o n, Position, Clock,
or Phase.
Resolution
Position G
Clock
2
3
Press the O K button and then use D or E or F or G
button to make appropriate adjustments.
■ The P h a s e adjustment range is -16 ~ +16.
■ The C l o c k adjustment range is -30 ~ +30.
Press the O K button.
Initializing (Reset to original factory values)
To initialize the adjusted values.
This function allows you to return to the good picture reproduction programmed at the factory and cannot be change.
1
Use D or E button to select Reset.
Phase
Reset
Move
Prev
Resolution XGA(1024, 1280, 1360,
1366(except 50PC5D*)) isn’t
distinguished because of having
the same H/V Sync Time.
This function is you to select the
Default Sync Time.
Position This function is to adjust picture
to left/right and up/down as you
prefer.
Clock
Clock This function is to minimize any vertical bars or stripes
visible on the screen background
the horizontal screen size will
also change.
Phase
This function allows you to
remove any horizontal noise and
clear or sharpen the image of characters.
Resolution
Position
Clock
2
Press the O K button and then use F or G button to
select Y e s.
Initialize Settings.
Phase
Reset
G
Yes
Prev
3
22
Press the O K button.
No
Select
OK
AV OUTPUT SETUP
The TV has a special signal output capability which RGB
allows
IN you to hook up a second TV or monitor.
RGB (PC)
OPTICAL
VIDEO
RS-232C IN
(CONTROL & SERVICE)
COMPONENT IN
2
EXTERNAL EQUIPMENT SETUP
Connect the second TV or monitor to the
HDMI/DVI IN
TV’s AV OUT jacks.
AV OUT
1
DIGITAL AUDIO OUT
REMOTE
CONTROL IN
See the Operating Manual
of the second TV or monitor
1
VIDEO settings.AUDIO
for further details regarding that device’s input
(MONO)
VIDEO
AV IN 1
2
S-VIDEO
AUDIO
AUDIO
1
! NOTE
G
Only Digital, Analogue mode can be used for AV out.
G
We recommend to use the AV OUT jacks for VCR recording.
VIDEO
L
S-VIDEO
R
DIGITAL AUDIO OUTPUT SETUP
Send the TV’s audio to external audio equipment via the Digital Audio Output (Optical) port.
IN
RGB IN
2
Connect the other end of the optical cable to COMPONENT
the digi- IN
2
tal audio (optical) input on the audio equipment.
DIGITAL AUDIO OUT
REMOTE
CONTROL IN
Set the “TV Speaker option - Off” in the AUDIO
VIDEO
menu. See the external audio equipment instruction
manual for operation.
VIDEO
RS-232C IN
(CONTROL & SERVICE)
1
1 (DVI)
3
OPTICAL
PTICAL
AV OUT
RGB (PC)
Connect one end of an optical cable to the TV
Digital
(
)
Audio Optical Out port.
AUDIO
DIO
AUDIO
(
) AUDIO
VIDEO MONO
AV IN 1
1
S-VIDEO
HDMI/DVI IN
! NOTE
G
When connecting with external audio equipments, such as
amplifiers or speakers, please turn the TV speakers off.
2
CAUTION
G
Do not look into the optical output port. Looking at the
laser beam may damage your vision.
23
WATCHING TV /PROGRAMME CONTROL
REMOTE CONTROL KEY FUNCTIONS
When using the remote control, aim it at the remote control sensor on the TV.
D/A INPUT Selects digital or analogue mode.
(Digital TV /
Analogue TV)
INPUT
D/A
POWER
MODE
TV
INPUT
WATCHING TV/PROGRAMME CONTROL
INPUT External input modes rotate in regular sequence: Digital,
Analogue, AV1-2, Component 1-2, RGB-PC, HDMI/DVI
IN 1or 2.
POWER Switches the set between ON and STANDBY.
SIMPLINK See a list of AV devices connected to TV.
When you toggle this button, the Simplink menu appears
at the screen.
BRIGHT Adjusts brightness on screen.
This returns to the default settings brightness by changing
mode source.
VCR
BRIGHT
SIMPLINK
DVD
RATIO TEXT INFO i GUIDE
1
SUBTITLE
MENU
EXIT
LIST
FAV
VCR/DVD Controls video cassette recorders or DVD players
control buttons ("RECORD" button is not available for DVD player).
OK
OK Accepts your selection or displays the current mode.
THUMBSTICK Adjusts menu settings.
(Up/Down/Left
Right) Selects menu item.
Q.VIEW
VOLUME Increase/decrease the sound level.
UP/DOWN
VOL
Q.VIEW Returns to the previously viewed programme.
MUTE Switches the sound on or off.
PROGRAMME Selects a programme.
UP/DOWN
PAGE UP/DOWN Move from one full set of screen information to the next
one.
PR
MUTE
1
2
3
4
5
6
7
8
9
I/II
0
SLEEP
SIZE
INDEX
TIME
NUMBER button Selects a programme. Selects numbered items in a menu.
I/II Selects the sound output or the audio mode.
SLEEP Sets the sleep timer.
24
?
REVEAL
PAGE
TV, VCR, DVD Selects the remote operating mode: TV, VCR, DVD. Select other operating modes, for the
remote to operate external devices.
RATIO Selects your desired picture format.
GUIDE Shows a programme schedule.
Coloured They are used as per the indications or functions displayed on the TV screen in the case of
buttons Text displays (Teletext, EPG) and programme edit.
EXIT Returns to TV viewing from any menu.
SUBTITLE Recalls your preferred subtitle in digital mode.
MENU Selects a menu.
LIST Displays the programme table.
FAV Displays the selected favourite programmes.
(FAVOURITE)
1
TELETEXT These buttons are used for teletext.
BUTTONS Text button is used to enable teletext services while other buttons are for teletext functions.
* For further details, see the ‘Teletext’ section.
Installing Batteries
Remote control effective range
INPUT
D/A
■
■
■
WATCHING TV/PROGRAMME CONTROL
INFOoo
i Shows the present screen information.
Open the battery compartment cover on the back
and install the batteries matching correct polarity
(+with +,-with -).
Install two 1.5V AA batteries. Don’t mix old or
used batteries with new ones.
Close cover.
MODE
TV
POWER
INPUT
VCR
BRIGHT
DVD
SIMPLINK
RATIO TEXT
i
SUBTITLE
INFO
MENU
i
GUIDE
LIST
■
Use a remote control up to 7 meters distance and
30 degree (left/right) within the receiving unit
scope.
■
Dispose of used batteries in a recycle bin to
preserve environment.
25
WATCHING TV/PROGRAMME CONTROL
TURNING ON THE TV
INPUT
D/A
MODE
TV
POWER
INPUT
VCR
BRIGHT
When your TV is turned on, you will be able to use its features.
DVD
SIMPLINK
Firstly, connect the power cord correctly.
At this stage, the TV switches to standby mode.
■ In standby mode, press the
, INPUT, P R D or E button on the TV or press the POWER, INPUT, D/A INPUT,
PR + or -, Number (0~9
9 ) button on the remote control
and the TV will switch on.
1
SUBTITLE
LIST
WATCHING TV/PROGRAMME CONTROL
FAV
OK
Q.VIEW
VOL
PR
PAGE
MUTE
When finished using the TV, press the POWER button on
the remote control. The TV reverts to standby mode.
3
MENU
GUIDE
EXIT
Select the viewing source by using the INPUT button on
the remote control.
■ This TV is programmed to remember which mode it was
last set to, even if you turn the TV off.
2
INFO
!
RATIO TEXT
1
2
3
4
5
6
7
8
9
I/II
0
SLEEP
SIZE
INDEX
TIME
?
REVEAL
! NOTE
G
If you intend to be away on vacation, disconnect the
power plug from the wall power outlet.
G
When the TV is turned on, the indicator will blink green
before the picture is seen.
INITIALIZING SETUP
Installation Guide
If the OSD (On Screen Display) is displayed on the screen
as figure 1 after turning on the set, you can adjust the Auto
Programme tuning, Time Zone selection or Password setting.
1
Welcome
Thank you for choosing LG.
The Following process guides you to complete
initial settings.
Before starting, be sure that the TV antenna
is connected.
Press OK(
) to continue.
Next
! NOTE
G
26
It will automatically disappear after approx, 40 seconds
unless a button is pressed.
Figure 1.
PROGRAMME SELECTION
Q.VIEW
VOL
Automatically finds all programmes available through
antenna inputs, and stores them in memory on the programme list.
PAGE
MUTE
1
2
3
4
5
6
7
8
9
I/II
0
SLEEP
SIZE
INDEX
TIME
?
REVEAL
VOLUME ADJUSTMENT
INPUT
D/A
Adjust the volume to suit your personal preference.
MODE
TV
POWER
INPUT
VCR
BRIGHT
DVD
SIMPLINK
1
INFO
GUIDE
Press the V O L + or - button to adjust the volume.
SUBTITLE
MENU
EXIT
2
!
RATIO TEXT
WATCHING TV/PROGRAMME CONTROL
1
Press the P R + or - or NUMBER buttons to select a
programme number.
PR
LIST
FAV
If you wish to switch the sound off, press the M U T E button.
OK
3
You can cancel the Mute function by pressing the M U T E,
I / I I or VOL + or - button.
Q.VIEW
VOL
PR
PAGE
MUTE
1
2
3
4
5
6
7
8
9
I/II
0
SLEEP
SIZE
INDEX
TIME
?
REVEAL
27
WATCHING TV/PROGRAMME CONTROL
ON-SCREEN MENUS SELECTION AND ADJUSTMENT
Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.
WATCHING TV/PROGRAMME CONTROL
1
Press the M E N U button and then use D or E button to select each menu.
2
Press the G button and then use
SETUP
D
or E or F or G button to display the available menus.
PICTURE
Auto Tuning
Picture Mode
Manual Tuning
Colour Temperature
Programme Edit
XD
Advanced
Aspect Ratio
: Auto
Picture Reset
Screen
AUDIO
LOCK
Lock System
: Off
Set Password
Block Programme
Parental Guidance
Input Block
Sound Mode
: Standard
Auto Volume
: On
Balance
:0
TV Speaker
: On
TIME
OPTION
Subtitle
: Off
Input Label
Clock
: -- -- ---- --: -- --
Off Time
: Off
: Off
SIMPLINK
: Off
On Time
Key Lock
: Off
Sleep Time
: Off
Set ID
:1
Auto Sleep
: Off
ISM Method
: Normal
Low Power
: Off
Factory Reset
Model Info
28
: Dynamic
SUBTITLE
FACTORY RESET
Use to quickly reset all the menu options to their original
factory preset values.
This function deletes all TV programmes.
To begin Factory Reset, input a 4-digit password in Lock
system. Be sure to remember this number!
7 ’, ‘7
7 ’, ‘7
7 ’, ‘7
7 ’ on the
If you forgot your password, press ‘7
remote control handset.
MENU
LIST
FAV
EXIT
OK
Subtitle
: Off
Input Label
SIMPLINK
: Off
Key Lock
: Off
Set ID
:1
Low Power
1
Press the M E N U button and then use D or E
button to select the O P T I O N menu.
2
Press the G button and then use D or E button
to select F a c t o r y R e s e t.
Factory Reset
Model Info
Subtitle
Selection(ON) resets all
users settings.
WARNING: All channel service and user settings will
be lost and return to initial
setting.
Input label
SIMPLINK
3
Press the G button and then use
POWERD or E button
to select O n or O f f.
Key Lock
Set ID
ISM Method
Low Power
4
Press E X I T button to return to normal TV viewing
or press M E N U button to return to the previous
menu.
Factory Reset
Off
On
G
Model Info
SUBTITLE
MENU
LIST
FAV
EXIT
MODEL INFO
WATCHING TV/PROGRAMME CONTROL
ISM Method
OK
This function enables you to watch Model, Software
Version.
Subtitle
: Off
Input Label
1
Press the M E N U button and then use D or E
button to select the O P T I O N menu.
SIMPLINK
: Off
Key Lock
: Off
Set ID
:1
ISM Method
Low Power
2
Press the G button and then use D or E button
to select M o d e l I n f o.
3
Press the G button to display Model, Software
Version.
Factory Reset
Model Info
Subtitle
Input label
SIMPLINK
4
Press E X I T button to return to normal TV viewing
or press M E N U button to return to the previous
menu.
Key Lock
Set ID
ISM Method
Low Power
Factory Reset
Model Info
G
MODEL : 42PC5D-AB
S/W Ver. : 1.18.00
29
POWER
WATCHING TV/PROGRAMME CONTROL
AUTO PROGRAMME TUNING
SUBTITLE
MENU
WATCHING TV/PROGRAMME CONTROL
A password is required to gain access to Auto programme or
Manual programme menu if the Lock system is turned on.
7 ’, ‘7
7 ’, ‘7
7 ’, ‘7
7 ’ on the
If you forgot your password, press ‘7
remote control.
In Australia, if no station name can be assigned to a station,
the programme number is assigned and stored as ----followed by a number see ‘Assigning a station name’ section
to assign the station name.
LIST
FAV
EXIT
OK
Q.VIEW
VOL
PR
PAGE
MUTE
1
2
3
4
5
6
7
8
9
I/II
0
SLEEP
Auto Tuning
1
Press the M E N U button and then D or E button to
select the S E T U P menu.
2
Press the G button and then D or E button to select
A u t o T u n i n g.
3
Press the G button to select T o S t a r t and then
press the F or G button to select N o.
Manual Tuning
Programme Edit
Auto Tuning
To Start
G
Manual Tuning
Programme Edit
4
Option
TV/DTV
Press the O K button.
Option: Select TV/DTV(analogue
and digital), TV(analogue only) or
DTV(digital only) to search.
Press
Auto Tuning
Manual Tuning
Programme Edit
(OK) to start.
To Start
All of programmes will be deleted.
continue?
Yes
F G
No
Move
Select
Option: Select TV/DTV(analogue
and digital), TV(analogue only) or
DTV(digital only) to search.
Press
30
(OK) to start.
Auto Tuning
Press the E button and then F or G button to select
TV(or DTV or TV/DTV) and then press the O K button.
5
Programme Edit
Option F
Press the O K button to begin auto programming.
All of analogue programmes are deleted and all analogue stations are stored.
Auto Tuning
Manual Tuning
To stop auto tuning, press the O K button.
When auto tuning is complete, the P r o g r a m m e E d i t
menu appears on the screen. See the ‘Programme Edit’
section to edit the stored programme.
G
Programme Edit
(OK) to start.
To Start
All of analogue programmes will
be deleted. continue?
Yes
F G
No
Move
Select
Option: Select TV/DTV(analogue
and digital), TV(analogue only) or
DTV(digital only) to search.
Press
(OK) to start.
Press E X I T button to return to normal TV viewing or
press M E N U button to return to the previous menu.
8
Auto Tuning
WATCHING TV/PROGRAMME CONTROL
Press
7
TV
Option: Select TV/DTV(analogue
and digital), TV(analogue only) or
DTV(digital only) to search.
Press the F or G button to select Y e s .
6
To Start
Manual Tuning
To Start
Manual Tuning
Processing Auto Tuning...
Programme Edit
V/UHF CH. 0 0%
No channel(s) found
! NOTE
G
In Auto Tuning mode, schedule list is deleted.
Press (OK) to stop
the current scan and
start digital
channel scan.
Option: Select
TV/DTV(analogue
and digital), TV(analogue only) or
DTV(digitalMENU
only) to
search.
Prev.
Press
(OK) to start.
31
WATCHING TV/PROGRAMME CONTROL
MANUAL PROGRAMME TUNING
INPUT
D/A
POWER
MODE
TV
POWER
INPUT
VCR
BRIGHT
In Digital Mode
DVD
SIMPLINK
INFO
!
RATIO TEXT
GUIDE
Manual programme lets you manually add a programme to
your programme list.
SUBTITLE
MENU
LIST
WATCHING TV/PROGRAMME CONTROL
FAV
EXIT
OK
Auto Tuning
1
Press the M E N U button and then use D or E button
to select the S E T U P menu.
2
Press the G button and then use D or E button to
select M a n u a l T u n i n g.
3
Press the G button and then use D or E button to
select the programme number you want to add.
Manual Tuning
Programme Edit
Auto Tuning
Manual Tuning
Programme Edit
G
Select the digital channel for
manual scanning.
43
4
Press the O K button to store the programme. When
the programme number you want to add is already
added in programme list, the message “ A l r e a d y p r o grammed channel. Do you want to update?”
will appear. If you want to keep on manual tuning,
select YES with using F or G button . Then, press the
O K button. Otherwise select N O.
When the programme is stored, the Programme edit
menu appears on the screen. See the ‘Programme Edit’
section to edit the stored programme.
Signal Strength
Auto Tuning
Manual Tuning
Programme Edit
Select the digital channel for
manual scanning.
D
E
7
Signal strength
5
32
Press E X I T button to return to normal TV viewing or
press M E N U button to return to the previous menu.
MANUAL PROGRAMME TUNING Continued
INPUT
D/A
POWER
MODE
TV
POWER
INPUT
VCR
BRIGHT
In Analogue Mode
DVD
SIMPLINK
INFO
!
RATIO TEXT
GUIDE
Manual programme lets you manually tune and arrange the stations in whatever order you desire. Also you can assign a station
name with five characters to each programme number.
SUBTITLE
MENU
Press the M E N U button and then use D or E button
to select the SETUP menu.
2
Press the G button and then use D or E button to
select M a n u a l T u n i n g.
WATCHING TV/PROGRAMME CONTROL
1
LIST
FAV
EXIT
OK
Auto Tuning
Manual Tuning
Programme Edit
3
Press the G button to select B a n d. Press the F or G
button to select V / U H F or C a b l e as required.
4
Press the E button to select C h a n n e l. Press the F
or G button to select the desired channel number.
5
Press the E button to select S e a r c h. Press the F or
G button to commence searching. If a station is found
the search will stop.
Auto Tuning
Manual Tuning
Programme Edit
G
Storage
0
Band
V/UHF
Channel
0
Search
Fine
Name
6
If this station is the one required, press the D or E
button to select Storage. Select the desired programme number with the F or G button.
7
Press the O K button to store it.
-----
Auto Tuning
Manual Tuning
Storage
Programme Edit
Band
Channel
0
F
V/UHF
G
0
Search
8
To store another station, repeat steps 3 to 7.
Fine
Name
-----
9
Press E X I T button to return to normal TV viewing or
press M E N U button to return to the previous menu.
store
33
WATCHING TV/PROGRAMME CONTROL
FINE TUNING - In Analogue Mode only
INPUT
D/A
POWER
MODE
TV
POWER
INPUT
VCR
BRIGHT
Normally fine tuning is only necessary if reception is poor.
The finely tuned programme will be indicated by a yellow
number during programme selection.
DVD
SIMPLINK
SUBTITLE
INFO
MENU
!
RATIO TEXT
GUIDE
LIST
WATCHING TV/PROGRAMME CONTROL
FAV
EXIT
OK
Auto Tuning
1
Press the M E N U button and then use
to select the S E T U P menu.
2
Press the G button and then use D or E button
select Manual Tuning.
3
Press the G button and then D or E button to
select F i n e.
D
or E button
Manual Tuning
Programme Edit
Auto Tuning
Manual Tuning
Programme Edit
G
Storage
Band
Channel
4
Press the F or G button to fine tune for the best
picture and sound.
0
V/UHF
0
Search
Fine
Name
-----
5
Press the O K button to store.
Auto Tuning
6
Press E X I T button to return to normal TV viewing or
press M E N U button to return to the previous menu.
Manual Tuning
Storage
Programme Edit
Band
Channel
0
V/UHF
1
Search
FG
Fine
Name
----store
34
ASSIGNING A STATION NAME - In Analogue Mode only
INPUT
D/A
POWER
MODE
TV
POWER
INPUT
VCR
BRIGHT
You can assign a station name with the characters to each
programme number.
DVD
SIMPLINK
SUBTITLE
INFO
MENU
!
RATIO TEXT
GUIDE
LIST
WATCHING TV/PROGRAMME CONTROL
FAV
EXIT
OK
Auto Tuning
1
Press the M E N U button and then use D or E button
to select the SETUP menu.
2
Press the G button and then use D or E button to
select Manual Tuning.
3
Press the G button and then use D or E button to
select N a m e.
Manual Tuning
Programme Edit
Auto Tuning
Manual Tuning
Programme Edit
4
G
Storage
0
Band
V/UHF
Channel
Press the F or G button. You can use the numeric 0
to 9 , the alphabet A to Z + , - , and blank.
0
Search
Fine
Name
-----
5
Press the D or E button to select the position and
make your choice of the second character, and so on.
Auto Tuning
6
Press the O K button to store.
Manual Tuning
Storage
Programme Edit
Band
0
V/UHF
Channel
1
Search
Fine
7
Press E X I T button to return to normal TV viewing or
press M E N U button to return to the previous menu.
Name
F
-----
G
store
35
WATCHING TV/PROGRAMME CONTROL
PROGRAMME EDIT
INPUT
D/A
MODE
TV
POWER
INPUT
VCR
BRIGHT
DVD
SIMPLINK
RATIO TEXT
INFO
SUBTITLE
!
This function enables you to delete or skip stored programmes. You can also move some channels to other programme numbers or copy a blank channel data into the
selected programme number.
GUIDE
LIST
MENU
WATCHING TV/PROGRAMME CONTROL
FAV
EXIT
OK
Auto Tuning
1
Press the M E N U button and then use D or E button
to select the S E T U P menu.
2
Press the G button and then use D or E button to
select Programme Edit.
3
Press the G button.
Manual Tuning
Programme Edit
Auto Tuning
Manual Tuning
4
Deleting a programme (In Analogue Mode Only)
a. Select a programme to be deleted with the D or E
or F or G button.
b. Press the R E D button twice. The selected programme is deleted, all the following programmes
are shifted up one position.
■
Copying a programme (In Analogue Mode Only)
a. Select a programme to be copied with the D or E
or F or G button.
b. Press the G R E E N button.
c. Move the programme to the desired programme
number with the D or E or F or G button.
d. Press the G R E E N button again to copy the programme. All the following programmes are shifted
down one position.
■
36
Programme Edit
G
Selection ( Gor ) leads
you to the programme edit
screen.
INPUT
D/A
MODE
TV
POWER
INPUT
VCR
BRIGHT
DVD
SIMPLINK
INFO
SUBTITLE
!
Skipping a programme number
a. Select a programme number to be skipped with D
or E or F or G button.
b. Press the B L U E button. The skipped programme
number turns to blue.
c. Press the B L U E button again to release the
skipped programme.
When a programme number is skipped it means that
you will be unable to select it using the P R + or - button during normal TV viewing. If you want to select
the skipped programme, directly enter the programme number with the NUMBER buttons or select
it in the programme edit or table menu.
RATIO TEXT
GUIDE
LIST
MENU
FAV
EXIT
OK
■
Q.VIEW
VOL
PR
MUTE
1
2
3
4
5
6
7
8
9
I/II
0
SLEEP
SIZE
INDEX
TIME
?
REVEAL
PAGE
WATCHING TV/PROGRAMME CONTROL
Moving a programme (In Analogue Mode Only)
a. Select a programme to be moved with D or E or
F or G button.
b. Press the Y E L L O W button.
c. Move the programme to the desired programme
number with the D or E or F or G button.
d. Press the Y E L L O W button again to release this
function.
■
Selecting Favourite Programme
a. Select your favourite programme number with D or
E or F or G button and then press the F A V button. It will automatically include the selected programme into your favourite programmes list and a
heartmark will appear in front of that programme
number.
■
5
Repeatedly press the F A V button to select stored
favourite programmes in normal TV viewing.
37
WATCHING TV/PROGRAMME CONTROL
INPUT LIST
INPUT
D/A
MODE
TV
POWER
INPUT
VCR
BRIGHT
DVD
AV2
RATIO TEXT
INFO
!
Press the INPUT button to display external device that is
connected to the unit, on screen.
Press the O K button to change the input to the active
external device. Use the INPUT button to select the input
source.
SIMPLINK
GUIDE
Input List
Digital
Analogue
AV 1
SUBTITLE
WATCHING TV/PROGRAMME CONTROL
AV 2
Component1
MENU
LIST
FAV
EXIT
E
OK
1
If all external input sources are connected:
Digital
2
Analogue
AV1
AV2
Component1
HDMI2
HDMI1
RGB-PC
Component2
If any external input sources are not connected:
Digital
3
Analogue
If there is any external input source connected:
(ex: When connected only to AV 2)
Digital
Analogue
AV2
Digital : Select it when watching the Digital TV.
Analogue : Select it when watching the Analog TV.
AV 1, AV 2 : Select it when watching the VCR or external equipment.
Component 1-2 : Select it when using the DVD or the Digital set-top box depend on connector.
RGB-PC : Select it when using PC depend on connector.
HDMI, HDMI2 : Select it when using DVD, PC or Digital set-top box depend on connector.
38
CALLING UP THE CHANNEL LIST
INPUT
D/A
MODE
TV
POWER
INPUT
VCR
BRIGHT
SIMPLINK
DVD
DIGITAL
ABC TV Sydney
RATIO TEXT
INFO
!
You can check the programmes stored in the memory by
displaying the channel list.
1
GUIDE
Channel List
1
Displaying Channel list
10
11
12
SUBTITLE
E
■
MENU
LIST
FAV
EXIT
Press the L I S T button to display the Channel List
menu.
The Channel list appears on the screen.
OK
Q.VIEW
PR
VOL
! NOTE
G
G
You may find some gray programmes.
They have been set up to be skipped by auto tuning or in
the programme edit mode.
Some programmes with the channel number shown in the
channel LIST indicate there is no station name assigned.
MUTE
1
2
3
4
5
6
7
8
9
I/II
0
SLEEP
SIZE
INDEX
TIME
?
REVEAL
PAGE
WATCHING TV/PROGRAMME CONTROL
13
Selecting a programme in the channel list
1
Select a programme with the D or E buttons.
2
The set switches to the chosen programme number.
Paging through a channel list
1
Press the D or E button to changes current channel into previous or next channel.
39
WATCHING TV/PROGRAMME CONTROL
INPUT SOURCE SELECTION
INPUT
D/A
MODE
TV
POWER
INPUT
VCR
BRIGHT
Alternatively you can select the Digital, Analogue, AV1-2,
Component 1-2, RGB-PC, HDMI1/2 mode by pressing the
INPUT button.
Press the D/A INPUT button to select digital or analogue
mode.
SIMPLINK
INFO
WATCHING TV/PROGRAMME CONTROL
MENU
!
RATIO TEXT
SUBTITLE
GUIDE
LIST
FAV
EXIT
OK
Subtitle
Press the M E N U button and then use D or E button
to select the OPTION menu.
1
Press the G button and then use D or E button to
select Input Label.
2
Press the G button and then use D or E to select
AV 1 , AV 2 , Component 1, Component 2, RGB-PC,
HDMI1/2.
3
Press the G button and then use D or E to select
POWER
the label.
4
: Off
Input label
SIMPLINK
: Off
Key Lock
: Off
Set ID
:1
ISM Method
: Normal
Low Power
: Off
Factory Reset
Model Info
Subtitle
Input Label
AV1
PC
SIMPLINK
AV2
VCR
Key Lock
Component1
DVD
Set ID
Component2
Set Top Box
ISM Method
RGB-PC
VCR
Low Power
HDMI1
Game
Factory Reset
HDMI2
Satellite
G
Model Info
5
Press E X I T button to return to normal TV viewing or
press M E N U button to return to the previous menu.
! NOTE
G
40
DVD
If you select PC label in HDMI1/2 mode, the picture size will be adjusted to PC mode size.
INPUT
D/A
MODE
TV
POWER
INPUT
VCR
BRIGHT
SIMPLINK
DVD
INFO
!
RATIO TEXT
GUIDE
This fundtion operates only with devices with the SIMPLINK logo. Please check the SIMPLINK logo.
SUBTITLE
MENU
OK
If you do not require the SIMPLINK menu, select “Off”.
Subtitle
1
2
3
Press the M E N U button and then use D or E
button to select the O P T I O N menu.
Press the G button and then use D or E button
to select S I M P L I N K.
Press the G button and then use D or E button
to select O n or O f f.
LIST
FAV
EXIT
: Off
Input label
SIMPLINK
: Off
Key Lock
: Off
Set ID
:1
ISM Method
: Normal
Low Power
: Off
Factory Reset
Model Info
WATCHING TV/PROGRAMME CONTROL
This allows you to control and play other AV devices
connected to the display through HDMI cable without
additional cables and settings.
Subtitle
Input label
SIMPLINK
Key Lock
4
Press E X I T button to return to normal TV viewing
or press M E N U button to return to the previous
menu.
G
Off
On
Set ID
ISM Method
Low Power
Factory Reset
POWER
Model Info
41
WATCHING TV/PROGRAMME CONTROL
SIMPLINK Functions
Disc playback
Control connected AV devices by pressing the D or E or F or G, O K buttons and buttons for play, stop, pause, fast
reverse, fast forward, chapter skip.(The
button does not provide such functions)
Direct Play
After connecting AV devices to theTV, you can directly control the devices and play media without additional settings.
Select AV device
Enables you to select one of AV devices connected to TV and play it.
WATCHING TV/PROGRAMME CONTROL
Power off all devices
When you switch off the TV, all connected devices are turned off.
Switch audio-out
Offers an easy way to switch audio-out.
* A device, which is connected to the TV through a HDMI cable but does not support SIMPLINK, does not
provide this function.
SIMPLINK Menu
Press the D or E or F or G button and then O K button to select the desired SIMPLINK source.
1
T V v i e w i n g : Switch to the previous TV programme
regardless of the current mode.
2
D I S C p l a y b a c k : Select and play discs. When multiple
discs are available, the titles of the discs are conveniently displayed at the bottom of the screen.
3
4
5
V C R p l a y b a c k : Control the connected VCR.
H D D R e c o r d i n g s p l a y b a c k : Control recordings
stored in HDD.
Audio Out to Home theatre/Audio Out to TV :
Select Home theatre or TV speaker for Audio Out.
1
G
Selected Device
2
3
4
5
G When
no device is
connected (displayed
in gray)
G When
a device is
connected (displayed
in bright colour)
! NOTE
Connect the HDMI/DVI IN or HDMI IN terminal of the TV to the rear terminal (HDMI terminal) of the
SIMPLINK device with the HDMI cable.
G After connecting the HDMI terminal for the home theater with SIMPLINK function using the above
method, connect the VARIABLE AUDIO OUT terminal on the back of the TV to the VARIABLE AUDIO IN
terminal on the back of the SIMPLINK device with the VARIABLE AUDIO OUT cable.
G When operating an external device with SIMPLINK, press the TV button from the MODE buttons on the
remote control.
G When you switch the Input source using the INPUT button on the remote control, you can stop the
operation of a device controlled by SIMPLINK.
G When you select or operate a media device with home theatre function, the speaker automatically
switches to home theatre speaker (HT speaker).
When
you execute ‘Photo List, Music List’ function during DVD playback included in home theater supportG
ed the SIMPLINK stops and the applicable function is executed after switching the input to TV.
G
42
INPUT
D/A
POWER
MODE
TV
POWER
INPUT
KEY LOCK
VCR
BRIGHT
DVD
SIMPLINK
RATIO TEXT
SUBTITLE
INFO
MENU
!
The TV can be set up so that it can only be used with the
remote control.
This feature can be used to prevent unauthorized viewing by
locking out the front panel controls.
This TV is programmed to remember which option it was last
set to even if you turn the TV off.
GUIDE
LIST
OK
Subtitle
Press the M E N U button and then use D or E button
to select the OPTION menu.
1
Press the G button and then use D or E button to
select Key Lock.
2
: Off
Input label
SIMPLINK
: Off
Key Lock
: Off
Set ID
:1
ISM Method
: Normal
Low Power
: Off
Factory Reset
Model Info
WATCHING TV/PROGRAMME CONTROL
FAV
EXIT
Press the G button and then use D or E button to
select O n or O f f .
3
Subtitle
Input Label
SIMPLINK
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
4
Key Lock
Set ID
G
Off
On
ISM Method
Low Power
Factory Reset
Model Info
! NOTE
G
With the lock on, the display ‘ K e y l o c k ’ appears on the screen if any button on the front panel is
pressed while viewing the TV.
G
The display ‘ K e y l o c k ’ will not appear on the screen if any button on the front panel is pressed
while displaying the menus.
43
EPG (ELECTRONIC PROGRAMME GUIDE)
INPUT
D/A
- In Digital Mode Only
MODE
TV
POWER
INPUT
VCR
BRIGHT
SIMPLINK
This system has an Electronic Programme Guide (EPG) to help your navigation through all the possible viewing options.
The EPG supplies information such as programme listings, start and end times
for all available services. In addition, detailed information about the programme is often available in the EPG (the availability and amount of these
programme details will vary, depending on the particular broadcaster).
DVD
RATIO TEXT
SUBTITLE
INFO i
MENU
EXIT
GUIDE
LIST
FAV
OK
This function can be used only when the EPG information is broadcasted by
broadcasting companies.
Q.VIEW
VOL
EPG(ELECTRONIC PROGRAMME GUIDE)
MUTE
Switch on/off EPG
1
Press the G U I D E button to switch on EPG.
2
Press the G U I D E or E X I T button again to switch off EPG and return to TV viewing.
Select a programme
1
44
PR
The EPG displays the programme description for next 7 days.
Press the D or E or F or G buttons to select desired programme, then press the O K
button to display the selected programme.
PAGE
Button Function in NOW/NEXT Guide Mode
Schedule
Function
Change to 7Day’s EPG Guide
Shows the Schedule list
Selects the Radio programmes
Select the Broadcasting Programme
Switch off EPG
The detail information on or off
Button Function in 7 Days Guide Mode
EPG(ELECTRONIC PROGRAMME GUIDE)
Remote Control Buttons
GREEN
YELLOW
BLUE
D/E/F/G
EXIT
INFO i
Sat 30 Jan
Schedule
Remote Control Buttons
GREEN
RED
YELLOW
BLUE
D/E/F/G
EXIT
INFO i
Function
Change to Now/Next Guide
Enter Timer Reservation/Cancel setting mode
Shows the Schedule List
Selects the Radio programmes
Select the Broadcasting Programme
Switch off EPG
Selects the page
Selects the day
The detail information on or off
45
EPG (ELECTRONIC PROGRAMME GUIDE)
Button Function in Extended Description Box
Digital
EPG(ELECTRONIC PROGRAMME GUIDE)
Remote Control Buttons Function
Change to the selected programme
INFO i
The detail information on or off
Button Function in Reservation Setting Mode
Schedule List
Programme
Start date
Remote Control Buttons Function
YELLOW
Change to Guide
PR +/ Page Up/Down
Delete the selected item
46
Start time
PICTURE CONTROL
PICTURE SIZE (ASPECT RATIO) CONTROL
INPUT
D/A
MODE
TV
POWER
INPUT
VCR
BRIGHT
DVD
RATIO TEXT
INFO
!
You can watch TV in various picture formats; Auto, 4:3, 16:9 (Wide), 14:9 and
Zoom.
SIMPLINK
GUIDE
! NOTE
G
1
If a fixed image is displayed on the screen for a long time, it image may
become imprinted on the screen and remain visible.
This phenomenon is common to all manufacturers and in consequence the
manufacturer’s warranty does not cover the product bearing this phenomenon.
SUBTITLE
MENU
EXIT
LIST
FAV
OK
Press the RATIO button repeatedly to select the desired picture format.
■
You can also adjust Aspect Ratio in the PICTURE menu.
Zoom
Selects the proper picture proportion to
match the source’s image. (4:3 4:3, 16:9
16:9)
Choose Zoom when you want to view the
picture without any alteration. However, the
top and bottom portions of the picture will be
cropped.
You can move the Zoom screen using D or E
button. The adjustment range is -16 - +16.
4:3
Choose 4:3 when you want to view a picture
with an original 4:3 aspect ratio.
PICTURE CONTROL
Auto
16:9
Adjust the picture horizontally, in a linear proportion to fill the entire screen.
POWER
14:9
The screen size is, more enlarged at both
sides, to create a spectacular view.
You can move the 14:9 screen using D or E
button. The adjustment range is -10 - +10.
! NOTE
G
G
In HDMI/DVI-PC and RGB-PC mode, 4:3 and 16:9 is available.
Auto: When your TV receives the wide screen signal, it will be automatically changed to the picture format
sent. (Not available in all countries)
47
PICTURE CONTROL
PRESET PICTURE SETTINGS
INPUT
D/A
POWER
MODE
TV
POWER
INPUT
VCR
BRIGHT
RATIO TEXT
Select this option to display a sharp image.
The most general and natural screen display status.
Select this option to display a mild image.
Selection this option to use a user defined setting.
SUBTITLE
INFO
MENU
Picture Mode
PICTURE CONTROL
Press the M E N U button and then use D or E button
to select the PICTURE menu.
: User1
Colour Temperature
: Cool
XD
Advanced
Aspect Ratio
: 16:9
Picture Reset
2
Press the G button and then use D or E button to
select P i c t u r e M o d e.
3
Press the G button and then use D or E button to
select Dynamic, Standard, M i l d, User1, or User2.
Screen
Picture Mode
4
Press E X I T button to return to normal TV viewing or
press M E N U button to return to the previous menu.
G
Dynamic
Colour Temperature
Standard
XD
Mild
Advanced
User 1
Aspect Ratio
User 2
Picture Reset
Screen
! NOTE
G
48
GUIDE
LIST
FAV
EXIT
OK
1
!
Picture Mode -Preset
Dynamic
Standard
Mild
User 1/2
DVD
SIMPLINK
In RGB-PC, HDMI-PC mode, to get the best picture quality, adjust the picture mode to Standard.
INPUT
D/A
POWER
MODE
TV
POWER
INPUT
VCR
BRIGHT
Auto Colour Tone Control (Warm/Medium/Cool)
DVD
SIMPLINK
INFO
!
RATIO TEXT
GUIDE
Choose one of three automatic colour adjustments. Set to
warm to enhance hotter colours such as red, or set to cool to
see less intense colours with more blue.
SUBTITLE
When selecting Picture Mode options (Dynamic, Standard and
Mild), Colour Temperature is automatically change.
MENU
OK
When selecting Picture Mode options (User 1 and User 2), you
can choose the Colour Temperature.
Picture Mode
Press the M E N U button and then use D or E button
to select the PICTURE menu.
Colour Temperature
: User1
: Cool
XD
Advanced
Aspect Ratio
: 16:9
Picture Reset
2
Press the G button and then use D or E button to
select Colour Temperature.
3
Press the G button and then use D or E button to
select either Cool, Medium, Warm or U s e r.
4
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Screen
PICTURE CONTROL
1
LIST
FAV
EXIT
Picture Mode
Colour Temperature G
Cool
XD
Medium
Advanced
Warm
Aspect Ratio
User
Picture Reset
Screen
49
PICTURE CONTROL
POWER
MANUAL PICTURE ADJUSTMENT
Picture Mode -User Option
SUBTITLE
MENU
LIST
FAV
EXIT
You can adjust picture Contrast, Brightness,Colour,
Sharpness, and Tint options to the levels you prefer.
OK
Q.VIEW
VOL
Picture Mode
1
Press the M E N U button and then use D or E button
to select the PICTURE menu.
PR
PAGE
: User1
Colour Temperature
XD
Advanced
Aspect Ratio
: 16:9
Picture Reset
PICTURE CONTROL
2
Press the G button and then use D or E button to
select Picture Mode.
3
Press the G button and then use D or E button to
select User 1 or User 2.
4
5
6
Press the G button and then use D or E button to
select the desired picture option (Contrast,
Brightness, Colour, Sharpness or T i n t).
Press the G button and then use F or G button to
make appropriate adjustments.
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Screen
Picture Mode
Dynamic
Colour Temperature
Standard
XD
Mild
Advanced
User 1
Aspect Ratio
User 2
Picture Reset
Screen
Selection ( G or ) leads you to
the detailed setting screen.
User1
Contrast
85
Brightness
50
Colour
50
Sharpness
50
Tint
Press
0
MENU
to confirm.
E
Contrast
E
50
G
85
G
R
G
POWER
SUBTITLE
Colour Tone -User Option
FAV
Q.VIEW
VOL
Picture Mode
Press the M E N U button and then use
to select the PICTURE menu.
D
or E button
LIST
OK
You can also adjust the detailed settings(Red, Green, Blue)
by selecting the U s e r menu.
This feature operate only if the picture mode set User 1 or
User 2.
1
MENU
EXIT
PR
PAGE
: User1
Colour Temperature
: Cool
XD
Advanced
Aspect Ratio
: 16:9
Picture Reset
D
or E button to
3
Press the G button and then use
select U s e r.
D
or E button to
4
Press the G button and then use
select R e d, Green, or B l u e.
D
or E button to
Screen
Picture Mode
Colour Temperature
Cool
XD
Medium
Advanced
Warm
Aspect Ratio
User
G
Picture Reset
Screen
PICTURE CONTROL
2
Press the G button and then use
select Colour Temperature.
Selection ( G or ) leads you to
the detailed setting screen.
5
Press the G button and then use
make appropriate adjustments.
F
or G button to
User
6
The adjustment range of R e d, G r e e n, or B l u e
is -20~ +20.
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Red
0
Green
0
Blue
0
Press
MENU
G
to confirm.
E
■
Red
0
E
51
PICTURE CONTROL
BRIGHTNESS ADJUSTMENT
INPUT
D/A
MODE
TV
POWER
INPUT
VCR
BRIGHT
DVD
SIMPLINK
BRIGHT
1
Press the
2
Adjust the desired screen brightness.
RATIO TEXT
GUIDE
button.
PICTURE CONTROL
1
POWER
52
INFO
!
Adjust the brightness using this button on the remote control.
2
XD - PICTURE IMPROVEMENT TECHNOLOGY
POWER
INPUT
D/A
MODE
TV
POWER
INPUT
VCR
BRIGHT
DVD
SIMPLINK
RATIO TEXT
INFO
!
XD is LG Electronics unique picture improving technology to display a real HD
source through an digital signal processing algorithm.
GUIDE
When selecting Picture Mode options (Dynamic, Standard and Mild), XD is
automatically change to Auto.
When selecting Picture Mode options (User 1 and User 2), you can choose
the Auto / Manual and when selecting Manual, you can adjust the XD
Contrast, XD colour and XD Noise.
SUBTITLE
MENU
LIST
FAV
EXIT
OK
1
Press the M E N U button and then use D or E button
to select the PICTURE menu.
Picture Mode
: User1
Colour Temperature
: Cool
XD
Press the G button and then use D or E button to
select X D.
PICTURE CONTROL
2
Advanced
Aspect Ratio
: 16:9
Picture Reset
Screen
3
Press the G button and then use F or G button to
select Auto or Manual.
* Selecting the Manual
1. Press the E button and then use D or E button to
select XD Contrast, XD Colour or XD Noise .
Picture Mode
Colour Temperature
XD
XD Contrast : Optimises the contract automatically
according to the brightness of the reflection.
■ X D C o l o u r : Adjusts the colour of the reflection
automatically to reproduce as close as possible to
natural colours.
■ X D N o i s e : Removing the noise up to the point where it
does not damage the original picture.
■
G
Manual
Advanced
Aspect Ratio
XD Contrast On
Picture Reset
XD Colour
On
Screen
XD Noise
On
2. Use the F or G button to select O n or O f f.
4
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
53
PICTURE CONTROL
ADVANCED - CINEMA
INPUT
D/A
POWER
MODE
TV
POWER
INPUT
VCR
BRIGHT
DVD
SIMPLINK
When you operate Cinema, the TV will adjust 24 fps video
from movies to 30 fps video for display (This function is
only available in TV(Analog, DTV), AV1, AV2, Component
480i, 576i mode.)
SUBTITLE
INFO
MENU
!
RATIO TEXT
To set the TV up for the best picture quality for viewing
films.
GUIDE
LIST
FAV
EXIT
OK
PICTURE CONTROL
Picture Mode
1
Press the M E N U button and then use D or E button
to select the PICTURE menu.
: User1
Colour Temperature
: Cool
XD
Advanced
Aspect Ratio
: 16:9
Picture Reset
2
Press the G button and then use D or E button to
select Advanced.
3
Press the G button and then use D or E button to
select Cinema.
Screen
Picture Mode
Colour Temperature
XD
4
Press the G button and then use F or G button to
select O n or O f f.
Advanced
Aspect Ratio
Picture Reset
Screen
5
54
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
G
Cinema
Off
Black Level
Low
ADVANCED - BLACK(DARKNESS) LEVEL
INPUT
D/A
POWER
MODE
TV
POWER
INPUT
VCR
BRIGHT
DVD
SIMPLINK
Adjusting the contrast and the brightness of the screen
using the black level of the screen.
This feature operates only in HDMI1, HDMI2 or AV1, AV2
mode.
SUBTITLE
INFO
MENU
!
RATIO TEXT
GUIDE
LIST
FAV
EXIT
OK
Picture Mode
: User1
Colour Temperature
PICTURE CONTROL
1
Press the M E N U button and then use D or E button
to select the PICTURE menu.
: Cool
XD
Advanced
Aspect Ratio
: 16:9
Picture Reset
2
Press the G button and then use D or E button to
select Advanced.
3
Press the G button and then use D or E button to
select Black level.
Screen
Picture Mode
Colour Temperature
XD
4
Press the G button and then use F or G button to
select L o w, or H i g h.
Advanced
Aspect Ratio
G
Cinema
Off
Black Level
Low
Picture Reset
Screen
5
■
Low
The reflection of the screen gets darker.
■
High
The reflection of the screen gets brighter.
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
55
PICTURE CONTROL
PICTURE RESET
INPUT
D/A
POWER
MODE
TV
POWER
INPUT
VCR
BRIGHT
DVD
SIMPLINK
Use to quickly reset all the Picture menu options to their original factory preset values.
SUBTITLE
INFO
MENU
!
RATIO TEXT
GUIDE
LIST
FAV
EXIT
OK
Picture Mode
1
PICTURE CONTROL
Press the M E N U button and then use D or E button
to select the PICTURE menu.
Colour Temperature
: User1
: Cool
XD
Advanced
Aspect Ratio
: 16:9
Picture Reset
2
Press the G button and then use D or E button to
select Picture Reset.
3
Press the G button to reset the Picture menu options
to original values.
Screen
Picture Mode
Colour Temperature
XD
Advanced
Aspect Ratio
Picture Reset
Screen
56
G Selection ( G or ) resets the
video configuration.
IMAGE STICKING MINIMIZATION(ISM)
METHOD
INPUT
D/A
POWER
MODE
TV
POWER
INPUT
VCR
BRIGHT
DVD
SIMPLINK
RATIO TEXT
SUBTITLE
INFO
MENU
!
A frozen still picture from a PC/video game displayed on
the screen for prolonged periods will result in a fixed ghost
image. Use our unique method to minimize any fixed image
on the screen.
LIST
FAV
EXIT
1
2
Press the M E N U button and then use D or E button
to select the O P T I O N menu.
OK
Press the G button and then use D or E button to
select I S M M e t h o d.
Subtitle
Press the G button and then use D or E button to
select either N o r m a l , O r b i t e r, I n v e r s i o n or
W h i t e W a s h.
■
■
■
Normal
If image sticking is never a problem, ISM is not necessary - set to Normal.
Orbiter
Orbiter may help prevent ghost images. However, it
is best not to allow any fixed image to remain on the
screen. To avoid a permanent image on the screen,
the image will move once per 2 minutes.
Inversion
Inversion will automatically invert the plasma display
panel color every 30 minutes.
SIMPLINK
: Off
Key Lock
: Off
Set ID
:1
ISM Method
: Normal
Low Power
: Off
Factory Reset
Model Info
Subtitle
Input Label
SIMPLINK
Key Lock
Set ID
ISM Method
Low Power
Factory Reset
■
White Wash
White Wash removes permanent images from the
screen.
: Off
Input label
PICTURE CONTROL
3
GUIDE
G
Normal
Orbiter
Inversion
White Wash
Model Info
! NOTE
G
4
An excessive permanent image may be impossible
to clear entirely with White Wash. To return to normal viewing, press any button.
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
57
PICTURE CONTROL
LOW POWER
INPUT
D/A
POWER
MODE
TV
POWER
INPUT
VCR
BRIGHT
This function allows you to reduce the power consumption of
the set.
DVD
SIMPLINK
SUBTITLE
INFO
MENU
OK
Subtitle
1
PICTURE CONTROL
2
3
Press the G button and then use D or E button to
select L o w P o w e r.
: Off
Input label
SIMPLINK
: Off
Key Lock
: Off
Set ID
:1
ISM Method
: Normal
Low Power
: Off
Factory Reset
Model Info
Press the G button and then use D or E button to
select O n or O f f.
Subtitle
■
When you select O n, the screen darkens.
Input Label
SIMPLINK
Key Lock
Set ID
4
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
ISM Method
Low Power
Factory Reset
Model Info
58
G
GUIDE
LIST
FAV
EXIT
Press the M E N U button and then use D or E button
to select the O P T I O N menu.
!
RATIO TEXT
Off
On
SOUND & LANGUAGE CONTROL
AUTO VOLUME LEVELER(AUTO VOLUME)
INPUT
D/A
POWER
MODE
TV
POWER
INPUT
VCR
BRIGHT
AVL automatically keeps on an equal volume level even if
you change programmes.
DVD
SIMPLINK
SUBTITLE
INFO
MENU
!
RATIO TEXT
GUIDE
LIST
FAV
EXIT
OK
Sound Mode
1
Press the M E N U button and then use D or E button
to select the AUDIO menu.
Press the G button and then use D or E button to
select Auto Volume.
3
Press the G button and then use D or E button to
select O n or O f f.
: On
Balance
:0
TV Speaker
: On
Sound Mode
Auto Volume
Balance
TV Speaker
4
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
G
Off
On
SOUND & LANGUAGE CONTROL
2
: Standard
Auto Volume
59
SOUND & LANGUAGE CONTROL
PRESET SOUND SETTINGS
-SOUND MODE
INPUT
D/A
POWER
MODE
TV
POWER
INPUT
VCR
BRIGHT
DVD
SIMPLINK
RATIO TEXT
Standard, Music, Movie, Sports and User are preset for
optimum sound quality at the factory and are not
adjustable.
SUBTITLE
INFO
MENU
SOUND & LANGUAGE CONTROL
60
Press the M E N U button and then use D or E button
to select the AUDIO menu.
2
Press the G button and then use D or E button to
select Sound Mode.
3
Press the G button and then use D or E button to
select S t a n d a r d, M u s i c, M o v i e, S p o r t s, or U s e r.
4
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Sound Mode
: Standard
Sound Mode
Auto Volume
: On
Auto Volume
Balance
:0
Balance
TV Speaker
: On
TV Speaker
G
Standard
Music
Movie
Sports
User
GUIDE
LIST
FAV
EXIT
OK
1
!
Sound Mode lets you enjoy the best sound without any
Special adjustment as the TV sets the appropriate sound
options based on the programme content.
SOUND SETTING ADJUSTMENT
-USER MODE
INPUT
D/A
POWER
MODE
TV
POWER
INPUT
VCR
BRIGHT
DVD
SIMPLINK
RATIO TEXT
SUBTITLE
INFO
MENU
!
Adjust the sound to suit your taste and room situations.
GUIDE
LIST
FAV
EXIT
OK
Sound Mode
1
Press the M E N U button and then use D or E button
to select the AUDIO menu.
Standard
Music
Movie
Sports
User
Auto Volume
Balance
TV Speaker
Press the G button and then use D or E button to
select Sound Mode.
3
Press the G button and then use D or E button to
select U s e r.
Selection ( G or ) leads you to
the detailed setting screen.
User
4
Press the G button and then use D or E button to
select the desired sound option ( Treble, Bass , or
Front Surround ).
Treble
50
Bass
50
Front Surround
Press
MENU
G
Off
SOUND & LANGUAGE CONTROL
2
G
to confirm.
61
SOUND & LANGUAGE CONTROL
Press the G button and then use
make appropriate adjustments.
5
or
button to
* Selecting the Front Surround
or
button to
Press the G button and then use
(
O
f
f
S
R
S
T
select
or
Sound Retrieval System)TruSurround
XT .
Front Surround
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
6
SOUND & LANGUAGE CONTROL
SRS TruSurround XT
Takes advantage of any multi-channel format without
needing to add extra speakers or equipment. Dialog
clarity, bass enrichment, and the addition of stereo
audio enhancement produces an immersive sound
experience from standard stereo material.
R
G
G
62
is a trademark of SRS Labs, Inc.
TruSurround XT technology is incorporated under license from SRS Labs, Inc.
TruSurround XT
SRS TruSurround XT
BALANCE
INPUT
D/A
POWER
MODE
TV
POWER
INPUT
VCR
BRIGHT
DVD
SIMPLINK
RATIO TEXT
SUBTITLE
INFO
MENU
!
Adjust the left/right sound of speaker to suit your taste and
room situations.
GUIDE
LIST
FAV
EXIT
OK
1
Press the M E N U button and then use D or E button
to select the AUDIO menu.
Press the G button and then use D or E button to
select Balance.
3
Press the G button and then use
make appropriate adjustments.
or
button to
: Standard
Auto Volume
: On
Balance
:0
TV Speaker
: On
Sound Mode
Auto Volume
Balance
0
L
R
0
L
R
TV Speaker
4
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Balance
SOUND & LANGUAGE CONTROL
2
Sound Mode
63
SOUND & LANGUAGE CONTROL
TV SPEAKERS ON/OFF SETUP
INPUT
D/A
POWER
MODE
TV
POWER
INPUT
VCR
BRIGHT
DVD
SIMPLINK
RATIO TEXT
SUBTITLE
INFO
MENU
OK
1
SOUND & LANGUAGE CONTROL
64
2
Press the G button and then use D or E button to
select TV Speaker.
3
Press the G button and then use D or E button to
select O n or O f f.
Sound Mode
: Standard
Auto Volume
: On
Balance
:0
TV Speaker
: On
Sound Mode
Auto Volume
Balance
4
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
TV Speaker
G
GUIDE
LIST
FAV
EXIT
Press the M E N U button and then use D or E button
to select the AUDIO menu.
!
Turn the TV speakers off if using external audio equipment.
Feature turns the TV Speakers option On or Off.
Off
On
I/II
INPUT
D/A
MODE
TV
POWER
INPUT
VCR
BRIGHT
DVD
SIMPLINK
RATIO TEXT
■
INFO
!
STEREO/DUAL RECEPTION - In Analogue Mode only
GUIDE
Mono sound selection
If the stereo signal is weak in stereo reception, you can switch to
mono by pressing the I / I I button twice. In mono reception, the
clarity of sound is improved. To switch back to stereo, press the
I / I I button twice.
SUBTITLE
MENU
EXIT
LIST
FAV
OK
Broadcast
On Screen Display
Mono
MONO
Q.VIEW
Stereo
MONO / STEREO
PR
VOL
PAGE
MUTE
SPEAKER SOUND OUTPUT SELECTION
2
3
4
5
6
7
8
9
I/II
0
SLEEP
SIZE
INDEX
TIME
?
REVEAL
Repeatedly press the I / I I button to select the sound output.
L+R: Audio signal from audio L input is sent to the left loud
speaker and audio signal from audio R input is sent to the right
loud speaker.
L+L: Audio signal from audio L input is sent to left and right loud
speakers.
R+R: Audio signal from audio R input is sent to left and right loud
speakers.
SOUND & LANGUAGE CONTROL
In AV 1-2, Component 1-2, RGB-PC or HDMI1/2 mode, you can
select output sound for the left and right loudspeakers.
1
! NOTE
In digital mode, if the OSD (On Screen Display) is
Displayed on the screen after press the I / I I button, you
can selected the audio language and type(MPEG or
DOLBY DIGITAL).
IN
MPEG mode only, you can selected L or R audio sound.
G
G
65
P
SOUND & LANGUAGE CONTROL
SUBTITLE - In Digital Mode only
INPUT
D/A
MODE
TV
POWER
INPUT
VCR
BRIGHT
You can select Subtitle on or off with the SUBTITLE button
in DTV mode.
DVD
SIMPLINK
SUBTITLE
INFO
MENU
EXIT
Subtitle
1
SOUND & LANGUAGE CONTROL
66
2
3
Press the G button and then use D or E button to
select Subtitle.
SIMPLINK
: Off
Key Lock
: Off
Set ID
:1
ISM Method
: Normal
Low Power
: Off
Factory Reset
Model Info
Press the G button and then use D or E button to
select O n or O f f.
Input Label
SIMPLINK
4
: Off
Input label
Subtitle
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Key Lock
Set ID
ISM Method
Low Power
Factory Reset
Model Info
G
GUIDE
LIST
FAV
OK
Press the M E N U button and then use D or E button
to select the OPTION menu.
!
RATIO TEXT
Off
On
TIME SETTING
CLOCK SETTING
INPUT
D/A
POWER
MODE
TV
POWER
INPUT
VCR
Auto Clock Setting
BRIGHT
DVD
SIMPLINK
!
RATIO TEXT
INFO
GUIDE
The time is set automatically from a digital channel signal.
The digital channel signal includes information for the current
time provided by the broadcasting station.
SUBTITLE
LIST
MENU
FAV
EXIT
Set the clock manually if the current time is set incorrectly by
the auto clock function.
OK
1
Press the M E N U button and then use D or E button
to select the T I M E menu.
Press the G button and then use D or E button to
select Clock.
3
Press the G button and then use D or E button to
select A u t o.
: -- -- ---- --:-- --
Off Time
: Off
On Time
: Off
Sleep Time
: Off
Auto Sleep
: Off
Clock
G
Off Time
Year
Date
Time
On Time
4
Press the G button and then use D or E button to
select your viewing area time zone :
N T, T A S, W A, S A, Q L D, V I C, or NSW/ACT.
5
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Auto
Sleep Time
---
---/ -: --
--
TIME SETTING
2
Clock
Auto Sleep
Time Zone
Clock
Off Time
On Time
Sleep Time
G
TAS
Auto
Year
Date
Time
---
---/ -: --
--
Auto Sleep
Time Zone
TAS
67
TIME SETTING
INPUT
D/A
POWER
MODE
TV
POWER
INPUT
Manual Clock Setting
VCR
BRIGHT
DVD
SIMPLINK
INFO
!
RATIO TEXT
GUIDE
If the current time setting is wrong, reset the clock manually.
SUBTITLE
MENU
LIST
FAV
EXIT
OK
1
TIME SETTING
2
Press the G button and then use D or E button to
select Clock.
3
Press the G button and then use D or E button to
select Manual.
Clock
: -- -- ---- --:-- --
Off Time
: Off
On Time
: Off
Sleep Time
: Off
Auto Sleep
: Off
Clock
4
5
68
Press the M E N U button and then use D or E button
to select the T I M E menu.
Press the G button and then use F or G button to
select either the year, date, or time option. Once
selected, use the D or E button to set the year, date,
and time options.
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Off Time
On Time
Sleep Time
Auto Sleep
G
Manual
Year
Date
Time
---
---/ -: --
--
AUTO ON/OFF TIMER SETTING
INPUT
D/A
POWER
MODE
TV
POWER
INPUT
VCR
BRIGHT
The timer function operates only if the current time has been set.
The Off-Time function overrides the On-Time function if they are
both set to the same time.
The TV must be in standby mode for the On-Time to work.
If you do not press any button within 2 hours after the TV turns on
with the On Time function, the TV will automatically revert to
standby mode.
DVD
SIMPLINK
SUBTITLE
INFO
MENU
!
RATIO TEXT
GUIDE
LIST
FAV
EXIT
OK
1
2
Press the M E N U button and then use D or E button
to select the T I M E menu.
Press the G button and then use D or E button to
select Off Time or On Time.
Press the G button and then use D or E button to
select O n.
■ To cancel O f f T i m e or O n T i m e function, select O f f.
4
Press the G button and then use D or E button to
set the hour.
: -- -- ---- --:-- --
Off Time
: Off
On Time
: Off
Sleep Time
: Off
Auto Sleep
: Off
TIME SETTING
3
Clock
Clock
Off Time
On Time
Sleep Time
5
6
Press the G button and then use D or E button to
set the minutes.
G
Off
On
Auto Sleep
Time
Ch.
Vol
6
: 30 AM
7
17
DIGITAL
Only On Time
Press the G button and then use D or E button to
select the channel at turn-on.
Press the G button and then use D or E button to
set the sound level at turn-on.
7
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
69
TIME SETTING
SLEEP TIMER SETTING
INPUT
D/A
MODE
TV
POWER
INPUT
VCR
You do not have to remember to switch the set off before you go
to sleep.
The sleep timer automatically switches the set to standby after
the preset time has elapsed.
BRIGHT
DVD
SIMPLINK
SUBTITLE
INFO
MENU
EXIT
!
RATIO TEXT
GUIDE
LIST
FAV
OK
1
Press the SLEEP button repeatedly to select the number of minutes. First the
O f f option appears on the screen, followed by the following Sleep Time
options : 10, 20, 30, 60, 90, 120, 180, and 240 minutes.
Q.VIEW
PR
VOL
MUTE
2
When the number of minutes you want is displayed on the screen, press the
O K button. The timer begins to count down from the number of minutes
selected.
1
2
3
4
5
6
7
8
9
I/II
0
SLEEP
SIZE
INDEX
TIME
?
TIME SETTING
3
To check the remaining minutes before the TV turns off, press the SLEEP
button once.
4
To cancel the Sleep Time, press the SLEEP button repeatedly to select O f f.
5
When you switch the set off, the set cancels the preset sleep time.
REVEAL
POWER
■
70
You can also set up the Sleep Time in the TIME menu.
Clock
: -- -- ---- --:-- --
Clock
Off Time
: Off
Off Time
On Time
: Off
On Time
Sleep Time
: Off
Sleep Time
Auto Sleep
: Off
Auto Sleep
G
Off
10 min
20 min
30 min
60 min
90 min
120 min
180 min
240 min
PAGE
AUTO SHUT-OFF SETTING
INPUT
D/A
POWER
MODE
TV
POWER
INPUT
VCR
BRIGHT
If the TV set is switched on and there is no input signal, it will
switch off automatically after 10 minutes.
DVD
SIMPLINK
SUBTITLE
INFO
MENU
!
RATIO TEXT
GUIDE
LIST
FAV
EXIT
OK
1
Press the M E N U button and then use D or E button
to select the T I M E menu.
Press the G button and then use D or E button to
select Auto Sleep.
3
Press the G button and then use D or E button to
select O n or O f f.
: -- -- ---- --:-- --
Off Time
: Off
On Time
: Off
Sleep Time
: Off
Auto Sleep
: Off
Clock
Off Time
TV will be automatically turned
off, in case of No Signal for 10
minutes.
On Time
4
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Sleep Time
Auto Sleep
G
TIME SETTING
2
Clock
Off
On
71
PARENTAL CONTROL / RATINGS
SET PASSWORD & LOCK SYSTEM
POWER
INPUT
D/A
MODE
TV
POWER
INPUT
VCR
Setting up your Password
BRIGHT
DVD
SIMPLINK
Set up blocking schemes to block specific channels, ratings, and
external viewing sources.
A password is required to gain access to this menu.
SUBTITLE
INFO
MENU
Press the M E N U button and then use the D or E button to
select the L O C K menu. Then, press the G button.
Enter the password as requested.
■ The TV is set up with the initial
password “0-0-0-0”.
■
PARENTAL CONTROL / RATING
72
Enter Password
GUIDE
LIST
FAV
EXIT
OK
1
!
RATIO TEXT
INPUT
D/A
POWER
MODE
TV
POWER
INPUT
VCR
Set Password
BRIGHT
DVD
SIMPLINK
INFO
!
RATIO TEXT
GUIDE
Change the password by inputting a new password twice.
SUBTITLE
MENU
LIST
FAV
EXIT
OK
1
After inputting the password, use the D or E button
to choose Set Password.
2
Press the G button and then choose any 4 digits for
your new password and enter the them on the N e w.
As soon as the 4 digits are entered, reenter the same
4 digits on the Confirm.
Then your changed password has been memorized.
! NOTE
G
Lock System
Set Password
Block Programme
Parental Guidance
Input Block
G
New
Confirm
PARENTAL CONTROL / RATING
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
3
Lock System
: Off
Set Password
Block Programme
Parental Guidance
Input Block
If you ever forget your password, key in ‘7’, ‘7’, ‘7’, ‘7’
on the remote control.
73
PARENTAL CONTROL /RATINGS
INPUT
D/A
MODE
TV
POWER
INPUT
VCR
Lock System
BRIGHT
DVD
SIMPLINK
RATIO TEXT
INFO i
GUIDE
Enables or disables the blocking scheme you set up previously.
SUBTITLE
MENU
OK
1
After inputting the password, use the D or E button
to choose Lock System.
2
Press the G button and then use the D or E to select
O f f or O n
■
Lock System
: Off
Set Password
Block Programme
Parental Guidance
Input Block
When you select, the Lock System is enable.
Lock System
PARENTAL CONTROL / RATING
74
3
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Set Password
Block Programme
Parental Guidance
Input Block
G
LIST
FAV
EXIT
Off
On
PROGRAMME BLOCKING
INPUT
D/A
MODE
TV
POWER
INPUT
VCR
BRIGHT
DVD
SIMPLINK
Blocks any programmes that you do not want to watch or
that you do not want your children to watch.
RATIO TEXT
SUBTITLE
INFO i
MENU
GUIDE
LIST
FAV
EXIT
OK
or E button
1
After inputting the password, use the
to choose Block Programme.
2
Press the G button. You will now see a screen filled
with channel numbers and a preview picture.
3
Use D or E or F or G button to select a channel
and then use the O K button to block or unblock it.
D
Lock System
: Off
Set Password
Block Programme
Parental Guidance
Input Block
Lock System
4
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Parental Guidance
Input Block
G
Selection ( G or
) leads you to
the block programme screen.
PARENTAL CONTROL / RATING
Set Password
Block Programme
75
PARENTAL CONTROL /RATINGS
PARENTAL GUIDANCE - In Digital Mode only
INPUT
D/A
MODE
TV
POWER
INPUT
VCR
Prevents children from watching certain children's TV programs, according to the ratings limit set.
BRIGHT
DVD
SIMPLINK
RATIO TEXT
SUBTITLE
INFO i
MENU
GUIDE
LIST
FAV
EXIT
OK
1
2
After inputting the password, use the
to choose P a r e n t a l G u i d a n c e.
D
or E button
Press the G button and then use the
select G , P G, M , M A, A V or R .
D
or E to
G (General audiences)
PG (Parental guidance suggested)
■ M (Mature audiences)
■ MA (Mature adult audiences)
■ AV (Adult audiences)
■ R (Restricted)
■ Blocking Off (Permits all programmes)
Lock System
: Off
Set Password
Block Programme
Parental Guidance
Input Block
■
■
PARENTAL CONTROL / RATING
76
3
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Lock System
Set Password
Block Programme
Parental Guidance
Input Block
Blocking off : permits
all programmes
G
G
PG
M
MA
AV
R
Blocking Off
EXTERNAL INPUT BLOCKING
INPUT
D/A
MODE
TV
POWER
INPUT
VCR
Enables you to select a source to block from the external
source devices you have hooked up.
BRIGHT
DVD
SIMPLINK
RATIO TEXT
SUBTITLE
INFO i
MENU
GUIDE
LIST
FAV
EXIT
OK
1
After inputting the password, use the D or E button
to choose Input Block.
2
Press the G button and then use the
select a source.
3
Press the G button and then use the
select O n or O f f on the each source.
4
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
D
Lock System
: Off
Set Password
Block Programme
Parental Guidance
Input Block
or E to
or
to
G
AV1
AV2
Component1
Component2
RGB-PC
HDMI1
HDMI2
On
On
Off
On
Off
On
Off
PARENTAL CONTROL / RATING
Lock System
Set Password
Block Programme
Parental Guidance
Input Block
77
TELETEXT
* This feature is not available in all countries.
- Teletext is a free service broadcast by some TV stations which gives up-to-the-minute information on news, weather, television programmes, share prices and many other topics.
- The teletext decoder of this TV can support the SIMPLE, TOP and FASTEXT systems. SIMPLE (standard teletext)
consists of a number of pages which are selected by directly entering the corresponding page number. TOP and
FASTEXT are more modern methods allowing quick and easy selection of teletext information.
Switch On/Off
Press the T E X T button to switch to teletext. The initial page or last page viewed appears on the screen.
Two page numbers, TV station name, date and time are displayed on the screen headline. The first page number indicates your selection, while the second shows the current page displayed.
Press the T E X T or E X I T button to switch off teletext.
SIMPLE Text
* This feature is not available in all countries.
■
Page selection
1
2
Enter the desired page number as a three digit number with the NUMBER buttons. If during selection you
press a wrong number, you must complete the three digit number and then re-enter the correct page
number.
The P R + or - button can be used to select the preceding or following page.
TOP Text
* This feature is not available in all countries.
- The user guide displays four fields-red, green, yellow and blue at the bottom of the screen. The yellow field
denotes the next group and the blue field indicates the next block.
TELETEXT
A Block / group / page selection
1
With the B L U E button you can progress from block to block.
2
Use the Y E L L O W button to proceed to the next group with automatic overflow to the next block.
3
With the G R E E N button you can proceed to the next existing page with automatic overflow to the next group.
Alternatively the P R + button can be used.
4
The R E D button return to the previous selection. Alternatively the P R - button can be used.
A Direct page selection
As with SIMPLE teletext mode, you can select a page by entering it as a three digit number using the NUMBER
buttons in TOP mode.
78
FASTEXT
- The teletext pages are colour coded along the bottom of the screen and are selected by pressing the corresponding coloured button.
A
Page selection
1. Press the i button to select the index page.
2. You can select the pages which are colour coded along the bottom line with corresponding coloured buttons.
3. Corresponding to the SIMPLE teletext mode, you can select a page by entering its three digit page number
with the NUMBER buttons in FASTEXT mode.
4. The P R + or - button can be used to select the preceding or following page.
Special Teletext Functions
?
REVEAL
Press this button to display concealed
information, such as solutions to riddles or
puzzles.
Press this button again to remove the information from the display.
TELETEXT
SIZE
Selects double height text.
Press this button to enlarge the top half of the
page.
Press this button again to enlarge the bottom
half of the page.
Press this button again to return to the normal
display.
TIME
When viewing a TV programme, press this
button to display the time at the top right
hand corner of the screen. Press this button
again to remove the display.
79
APPENDIX
TROUBLESHOOTING
The TV set does not operate properly.
Check to see if there is any object between the product and the remote control
causing obstruction. Ensure you are pointing the remote control directly at the TV.
■ Ensure that the batteries are installed with correct polarity (+ to +, - to -).
■ Ensure that the correct remote operating mode is set: TV, VCR etc.
■ Install new batteries.
■
The remote control does
not work
Is the sleep timer set?
Check the power control settings. Has the Power supply been interrupted.
■ Is Auto sleep activated on this station.
■
Power is suddenly
turned off
■
The video function does not work.
Check whether the TV set is switched on.
■ Try another channel. The problem may be with the broadcast.
■ Is the power cord inserted correctly into the mains?
■ Check your antenna direction and/or location.
■ Test the mains outlet by plugging another product into the same outlet.
■
No picture & No sound
Picture appears slowly
after switching on
■
This is normal, the image is muted during the product startups process. Please
contact your service center, if the picture has not appeared after five minutes.
Adjust Colour in menu option.
■ Allow a sufficient distance between the product and the VCR.
■ Try another channel. The problem may be with the broadcast.
■ Are the video cables installed properly?
■ Activate any function to restore the brightness of the picture.
■
No or poor colour
or poor picture
APPENDIX
Horizontal/vertical bars
or picture shaking
Poor reception on
some channels
Lines or streaks
in pictures
80
■
Check for local interference such as an electrical appliance or power tool.
Station or cable product experiencing problems, tune to another station.
Station signal is weak, reposition the antenna to receive weaker stations.
■ Check for sources of possible interference.
■
■
■
Check antenna (Change the position of the antenna).
The audio function does not work.
Press the VOL or VOLUME button.
■ Sound muted? Press MUTE button.
■ Try another channel. The problem may be with the broadcast.
■ Are the audio cables installed properly?
■
Picture OK & No sound
No output from one
of the speakers
Unusual sound from
inside
the product
■
Adjust Balance in menu option.
■
A change in ambient humidity or temperature may result in an unusual noise when
the product is switched on or off and does not indicate a fault with the product.
There is a problem in PC mode. (Only PC mode applied)
The signal is out of range
(Invalid format)
Vertical bar or stripe on
background &
Horizontal Noise &
Incorrect position
Screen colour is unstable
or single colour
■
Adjust resolution, horizontal frequency, or vertical frequency.
Check the input source.
■
Use Auto configure or adjust clock, phase, or H/V position.
■
Check the signal cable.
■ Reinstall the PC video card.
■
APPENDIX
81
APPENDIX
MAINTENANCE
Early malfunctions can be prevented. Careful and regular cleaning can prolong the life of your new TV.
Caution: Be sure to swith the power off and unplug the power cord before you begin any cleaning.
Cleaning the Screen
1
A good way to keep the dust off your screen for a while is to wet a soft cloth in a mixture of lukewarm water
and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to
wipe the screen.
2
Ensure there is no excess water on the screen. Allow any water or dampness to evaporate before switching
on.
Cleaning the Cabinet
■
■
To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
Do not to use a wet cloth.
Extended Absence
CAUTION
If you expect to leave your TV dormant for prolonged periods (such as a holiday), unplug the power
cord to protect against possible damage from lightning or power surges.
APPENDIX
82
PRODUCT SPECIFICATIONS
42PC5D*
(42PC5D-AB)
MODELS
Including stand
Dimensions
(Width x Height x Depth) Excluding stand
Weight
including stand
excluding stand
Television System
1242.0 x 887.6 x 370.0mm
48.9 x 34.9 x 14.6 inches
1048.0 x 713.0 x 83.5 mm
41.3 x 28.1 x 3.3 inches
1242.0 x 827.2 x 88.0 mm
48.9 x 32.6 x 3.5 inches
28.0 kg / 61.7 lbs
24.6kg / 54.2 lbs
39.3 kg / 86.6 lbs
34.6kg / 76.2 lbs
AC100-240V~ 50/60Hz 4.5A
PAL B/G, DVB-T
Program Coverage
External Antenna Impedance
Operating Temperature
VHF 0-12, UHF 20-75, CATV 02-44, DTV 06-12, 27-69
75 ohm
32 ~ 104°F (0 ~ 40°C)
Operating Humidity
Less than 80%
Storage Temperature
-4 ~ 140°F (-20 ~ 60°C)
Storage Humidity
■
1048.0 x 766.0 x 310.0 mm
41.3 x 30.2 x 12.2 inches
AC100-240V~ 50/60Hz 3.5A
Power requirement
Environment condition
50PC5D*
(50PC5D-AB)
Less than 85%
The specifications shown above may be changed without prior notice for quality improvement.
APPENDIX
83
APPENDIX
PROGRAMMING THE REMOTE CONTROL
The remote control is a multi brand or universal remote. It can be programmed. to operate most remote
controlled devices from other manufacturers.
Note that the remote control may not control all models from other brands.
Programming a code into a remote mode
APPENDIX
84
1
To find out whether your remote control can operate each device without programming, turn on the device
(such as a VCR) and press the corresponding mode button on the remote.
After that, press the POWER button. If the device is turned off and it responds properly the remote control
need not be programmed. If not, the remote should be programmed to operate the device. The programming procedures are explained below.
2
Press the M E N U and M U T E button continuously at the same time for two seconds; the currently selected
device button is illuminated.
If you don't press any button for 20 seconds, the light on the mode button will be turned off. In that case,
you have to repeat from step 2.
3
Enter the appropriate code from the code table on the following pages. When pressing the button, the light
blinks at a time. If the device turned off, the programming is successful.
4
Press the M E N U button to store the code. After blinking twice, this code is stored.
5
Test the remote control functions to see if the device responds properly. If not, steps 2-5.
Remote control code
VCRs
Brand
AIWA
AKAI
Codes
Codes
Brand
MAGNAVOX
031 033 034 041
067 068
012 031 033 067
SAMSUNG
043 046 124
146
MARANTZ
069
033
023
037
031
103
039 043
129
033
MARTA
MATSUI
MEI
MEMOREX
040
033
007
108
116
135
041
010 064
110 111
117 119
MGA
MINOLTA
MITSUBISHI
101
027
031
003
033
101
045
013
013
049
151
034
024
012
048
043
053
066
133
023 039 043
053
017
031
037
131
008
025
034
046
138
009
033
109
136
012
018
063
033
033
013
066
063 072
144 147
031
050
150
034
048
012
106
027
035
101
153
010
045
026 034
137 150
015 033
101
033 043
055 060
152
039 043
MTC
MULTITECH
NEC
NORDMENDE
OPTONICA
PANASONIC
PENTAX
PHILCO
PHILIPS
PILOT
PIONEER
PORTLAND
PULSAR
QUARTZ
QUASAR
RCA
REALISTIC
013 020
114 123
009 013 014
034 101 106
RICO
RUNCO
SALORA
013
063
031
031
067
101
013
108
072
011
033
013
040
107
145
003
031
053
058
148
014
030
033
010
034
102
046
020
020
051
014 031
053 072
134 139
059
045 046
059 061
040
034
023 039 043
054
070 074 083
140 145
020 031 033
034 067
033 034 054
071 101
021 048
014
066
020
041
109
147
008
033
054
075
033
062
140
145
034
063
144
010 014
034 040
101
Codes
032
105
113
125
SANSUI
022
SANYO
003
102
SCOTT
017
131
SEARS
003
013
031
101
SHARP
031
SHINTOM
024
SONY
003
056
077
SOUNDESIGN
034
STS
013
SYLVANIA
031
067
SYMPHONIC
034
TANDY
010
TATUNG
039
TEAC
034
TECHNICS
031
TEKNIKA
019
101
THOMAS
034
TMK
006
TOSHIBA
008
059
TOTEVISION
040
UNITECH
040
VECTOR RESEARCH 012
VICTOR
048
VIDEO CONCEPTS 012
VIDEOSONIC
040
WARDS
003
031
053
YAMAHA
012
ZENITH
034
058
040 102 104
107 109 112
115 120 122
043 048 135
007 010 014
134
037 112 129
008 009 010
014 017 020
042 073 081
054 149
009 031 052
057 058 076
078 149
033 034 059
034
043
039 043
033 070
031 033 034
013 042 047
082 112 131
101
APPENDIX
034
016
125
AMPRO
072
ANAM
031
AUDIO DYNAMICS 012
BROKSONIC
035
CANON
028
CAPEHART
108
CRAIG
003
CURTIS MATHES 031
DAEWOO
005
065
112
DAYTRON
108
DBX
012
DYNATECH
034
ELECTROHOME 059
EMERSON
006
029
036
129
FISHER
003
FUNAI
034
GE
031
107
GO VIDEO
132
HARMAN KARDON
HITACHI
004
043
INSTANTREPLAY 031
JCL
031
JCPENNY
012
040
JENSEN
043
JVC
012
048
130
KENWOOD
014
047
LG (GOLDSTAR) 001
101
LLOYD
034
LXI
003
017
MAGIN
040
Brand
034 046
013
033
054
034
048
072
017
034
131
039
056
080
024
040
043
101
85
APPENDIX
VCRs
Brand
Codes
ABC
003
046
AJIN
112
ANTRONIK
014
ARCHER
005
CABLE STAR
026
CENTURION
092
CENTURY
007
CITIZEN
007
COLOUR VOICE 065
COMBANO
080
COMTRONICS
019
DIAMOND
023
EAGLE
020
EASTERN
057
ELECTRICORD
032
GE
072
GEMINI
008
GI
052
GOLDEN CHANNEL 030
HAMLIN
049
HITACHI
052
HOSPITALITY
070
JERROLD
002
009
004 039 042
052 053
007 014 024
Brand
LG (GOLDSTAR)
M-NET
MACOM
MAGNAVOX
MEMOREX
MOVIE TIME
NSC
090
081
030
OAK
PANASONIC
PARAGON
030 040
062 066
PHILIPS
022 025 054
074
050 055
055
077
003 004 008
010 052 069
Codes
Brand
074
001
037
033
010
100
028
015
073
016
044
100
REMBRANT
025
SAMSUNG
102 107 030
SCIENTIFIC ATLANTA 003 011 041
043 045 046
SHERITECH
022
SIGNAL
030
SIGNATURE
052
SL MARX
030
SPRUCER
047 078
STARCOM
002 004 008
STARGATE
008 030
TADIRAN
030
TAEKWANG
110
TAIHAN
105
TANDY
017
TEXSCAN
029
TOCOM
039 040 056
TOSHIBA
100
UNIKA
007 014 024
UNITED CABLE
004 053
UNIVERSAL
005 007 014
026 027 032
VIEWSTAR
012 015 018
087 088 089
ZENITH
100 114 060
006
065
PIONEER
034
076
POST NEWS WEEK016
PRUCER
059
PTS
011
073
PULSAR
100
RCA
047
REGAL
049
REGENCY
057
106 101 005
012 064 079
032
028 038 071
031 037 053
047
012 013 020
085 090
051 052 063
048 071 072
074
050
Codes
DVD
Brand
APPENDIX
86
Codes
APEX DIGITAL
022
DENON
020
GE
005
HARMAN KARDON
JVC
012
LG
001
MAGNAVOX
013
MARANTZ
024
014
006
027
010 016 025
Brand
Codes
Brand
Codes
MITSUBISHI
NAD
ONKYO
PANASONIC
PHILIPS
PIONEER
PROCEED
PROSCAN
002
023
008
003
013
004
021
005
RCA
SAMSUNG
SONY
THOMPSON
TOSHIBA
YAMAHA
ZENITH
005
011
007
005
019
009
010
017
009
026
006
006
015
006
008
018
016 025
068
042
009
024
035
086
093
IR CODES
1. How to Connect
■
Connect your wired remote control to the Remote Control port on the TV.
2. Remote Control IR Codes
■
Output waveform
Single pulse, modulated with 37.917KHz signal at 455KHz
Carrier frequency
Tc
FCAR = 1/TC = fOSC/12
Duty ratio = T1/TC = 1/3
T1
■
Configuration of frame
1st frame
Lead code
Low custom code
High custom code
Data code
C0 C1 C2 C3 C4 C5 C6 C7
Data code
D0 D1 D2 D3 D4 D5 D6 D7
Repeat frame
Repeat code
■
Tf
Lead code
9 ms
4.5 ms
■
Repeat code
0.55 ms
■
2.25 ms
Bit description
Bit ”0”
Bit ”1”
0.56 ms
0.56 ms
2.24 ms
1.12 ms
■
APPENDIX
9 ms
Frame interval: Tf
The waveform is transmitted as long as a key is depressed.
Tf
Tf
Tf=108ms @455KHz
87
APPENDIX
APPENDIX
88
(Hexa)
Code
Function
Note
Code
50
D/A INPUT
Remote control Button
64
SIZE
Remote control Button
0B
INPUT
Remote control Button
70
INDEX
Remote control Button
79
RATIO
Remote control Button
26
TIME
Remote control Button
0E
SLEEP
Remote control Button
2A
REVEAL
Remote control Button
10-19
Number Key 0-9
Remote control Button
20
TEXT
Remote control Button
1A
Q.VIEW
Remote control Button
72
RED
Remote control Button
09
MUTE
Remote control Button
71
GREEN
Remote control Button
02
VOL +
Remote control Button
63
YELLOW
Remote control Button
03
VOL -
Remote control Button
61
BLUE
Remote control Button
(Hexa)
Function
Note
00
PR +
Remote control Button
53
LIST
Remote control Button
01
PR -
Remote control Button
0A
I/II
Remote control Button
1E
FAV
Remote control Button
AA
INFO
Remote control Button
40
D
Remote control Button
E1
41
E
Remote control Button
E0
Remote control Button
07
F
Remote control Button
B1
Remote control Button
06
G
Remote control Button
B0
Remote control Button
44
OK
Remote control Button
BA
Remote control Button
43
MENU
Remote control Button
BD
Remote control Button
5B
EXIT
Remote control Button
B2
Remote control Button
A9
GUIDE
Remote control Button
8F
Remote control Button
7E
SIMPLINK
Remote control Button
8E
Remote control Button
39
SUBTITLE
Remote control Button
B3
Remote control Button
Remote control Button
EXTERNAL CONTROL THROUGH RS-232C
Connect the RS-232C (serial port) input jack to an external control device (such as a computer
or an A/V control system) to control the product’s functions externally.
Connect the serial port of the control device to the RS-232C jack on the product back panel.
Note: RS-232C connection cables are not supplied with the product.
HDMI/DVI IN
RGB IN
RS-232C Setup
DIGITAL AUDIO OUT
RGB (PC)
AV OUT
VIDEO
RS-232C IN
(CONTROL & SERVICE)
COMPONENT IN
AUDIO
VIDEO
(MONO)
AUDIO
AV IN 1
VIDEO
S-VIDEO
AUDIO
(DVI)
PC
Type of Connector; D-Sub 9-Pin Male
Pin Name
1
2
3
4
5
6
7
8
9
No connection
RXD (Receive data)
TXD (Transmit data)
DTR (DTE side ready)
GND
DSR (DCE side ready)
RTS (Ready to send)
CTS (Clear to send)
No Connection
APPENDIX
No.
89
APPENDIX
RS-232C Configurations
7-Wire Configurations (Standard RS-232C cable)
RXD
TXD
GND
DTR
DSR
RTS
CTS
PC
PDP
2
3
5
4
6
7
8
3
2
5
6
4
8
7
D-Sub 9
D-Sub 9
TXD
RXD
GND
DSR
DTR
CTS
RTS
3-Wire Configurations(Not standard)
RXD
TXD
GND
DTR
DSR
RTS
CTS
PC
PDP
2
3
5
4
6
7
8
3
2
5
6
4
7
8
D-Sub 9
D-Sub 9
TXD
RXD
GND
DTR
DSR
RTS
CTS
Set ID
Use this function to specify a TV ID number.
Refer to ‘Real Data Mapping 1’. p .92
Subtitle
1
2
3
Press the M E N U button and then use D or E button
to select the OPTION menu.
Press the G button and then use D or E button to
select Set ID.
APPENDIX
Press the G button and then use D or E button to
adjust Set ID to choose the desired TV ID number.
The adjustment range of Set ID is 1~99.
SIMPLINK
: Off
Key Lock
: Off
Set ID
:1
ISM Method
: Normal
Low Power
: Off
Factory Reset
Model Info
Subtitle
Input Label
SIMPLINK
Key Lock
Set ID
ISM Method
4
Press E X I T button to return to TV viewing or press
M E N U button to return to the previous menu.
Communication Parameters
Baud rate : 9600 bps (UART)
■ Data length : 8 bits
■ Parity : None
■
90
: Off
Input Label
Stop bit : 1 bit
■ Communication code : ASCII code
■ Use a crossed (reverse) cable.
■
Low Power
Factory Reset
Model Info
G
1
Command Reference List
COMMAND1 COMMAND2
DATA
(Hexadecimal)
COMMAND1 COMMAND2
DATA
(Hexadecimal)
01. Power
k
a
0~1
15. Bass
k
s
0 ~ 64
02. Input Select
k
b
0~8
16. Balance
k
t
0 ~ 64
03. Aspect Ratio
k
c
See p.92
17. Colour Temperature
k
u
0~2
04. Screen Mute
k
d
0~1
18. Red Adjustment
k
v
0 ~ C8
05. Volume Mute
k
e
0~1
19. Green Adjustment
k
w
0 ~ C8
k
$
0 ~ C8
06. Volume Control
k
f
0 ~ 64
20. Blue Adjustment
07. Contrast
k
g
0 ~ 64
21. Channel Tuning
m
a
See p.94
j
p
0~3
08. Brightness
k
h
0 ~ 64
22. ISM Method
09. Colour
k
i
0 ~ 64
23. Low Power
j
q
0~1
24. Orbiter Time
Setting
j
r
1~ FE
25. Orbiter Pixel
Setting
j
s
1~ 3
26. Send IR Code
m
c
See p.94
27. Input Select
x
b
See p.94
10. Tint
k
j
0 ~ 64
11. Sharpness
k
k
0 ~ 64
12. OSD Select
k
l
0~1
k
m
0~1
13. Remote Control/
Key Lock
14. Treble
k
r
0 ~ 64
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1] : First command to control the set.(j, k, m or x)
[Command 2] : Second command to control the set.
on transmission/receiving protocol.
[DATA] : To transmit command data.
Transmit ‘FF’ data to read status of command.
[Cr] : Carriage Return
ASCII code ‘0x0D’
[ ] : ASCII code ‘space (0x20)’
[Command2][ ][Set ID][ ][OK][Data][x]
The TV transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is
data read mode, it indicates present status data. If the data is
data write mode, it returns the data of the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
APPENDIX
[Set ID] : You can adjust the set ID to choose desired TV ID
number in Setup menu. Adjustment range is 1~ 99.
When selecting Set ID ‘0’, every connected the TV
is controlled. Set ID is indicated as decimal (1~
99) on menu and as Hexa decimal (0x0~ 0x63)
OK Acknowledgement
The TV transmits ACK (acknowledgement) based on this format when receiving abnormal data from non-viable functions
or communication errors.
Data1: Illegal Code
Data2: Not supported function
Data3: Wait more time
91
APPENDIX
0 1 . Power (Command2:a)
To control Power On/Off of the TV.
Transmission [k][a][ ][Set ID][ ][Data][Cr]
Data 0 : Power Off
Data 1 : Power On
Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x]
* In a like manner, if other functions transmit ‘FF’ data
based on this format, Acknowledgement data feedback
presents status about each function.
02. Input Select (Command2:b)
To select input source for the TV.
Transmission [k][b][ ][Set ID][ ][Data][Cr]
Data 0: Digital
Data 5: Component 2
Data 1: Analogue
Data 6: RGB-PC
Data 2: AV1
Data 7: HDMI1
Data 3: AV2
Data 8: HDMI2
Data 4: Component 1
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
Data 1 : Volume mute off (Volume on)
Acknowledgement [e][ ][Set ID][ ][OK/NG][Data][x]
06. Volume Control (Command2:f)
To adjust volume.
You can also adjust volume with the volume buttons on
remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
Refer to ‘Real data mapping1’ as shown below.
Acknowledgement [f][ ][Set ID][ ][OK/NG][Data][x]
07. Contrast (Command2:g)
To adjust screen contrast.
You can also adjust contrast in the Picture menu.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
Refer to ‘Real data mapping1’ as shown below.
Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]
03. Aspect Ratio (Command2:c)
To adjust the screen format.
You can also adjust the screen format using the RATIO
button on remote control or in the PICTURE menu.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Date 0: Auto
1: 4:3
2: 16:9
3: 14:9 (-10) ~ D: 14:9 (0) ~ 17: 14:9 (10)
18: Zoom (-16) ~ 28: Zoom (0) ~ 38: Zoom (16)
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
* Using the PC input, you select either 16:9 or 4:3
screen aspect ratio.
0 4 . Screen Mute (Command2:d)
APPENDIX
To select screen mute on/off.
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data 0 : Screen mute off (Picture on)
Data 1 : Screen mute on (Picture off)
Acknowledgement [d][ ][Set ID][ ][OK/NG][Data][x]
05. Volume Mute (Command2:e)
To control volume mute on/off.
You can also adjust mute using the MUTE button on
remote control.
Transmission [k][e][ ][Set ID][ ][Data][Cr]
Data 0 : Volume mute on (Volume off)
92
0 8 . Brightness (Command2:h)
To adjust screen brightness.
You can also adjust brightness in the PICTURE menu.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64(*transmit by Hexadecimal code)
Refer to ‘Real data mapping1’ as shown below.
Acknowledgement [h][ ][Set ID][ ][OK/NG][Data][x]
09. Colour (Command2:i)
To adjust the screen colour.
You can also adjust colour in the PICTURE menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
Refer to ‘Real data mapping1’ as shown below.
Acknowledgement [i][ ][Set ID][ ][OK/NG][Data][x]
*Real data mapping 1
0 : Step 0
A : Step 10 (SET ID 10)
F : Step 15 (SET ID 15)
10 : Step 16 (SET ID 16)
63 : Step 99 (SET ID 99)
64 : Step 100
10. Tint (Command2:j)
16. Balance (Command2:t)
To adjust the screen tint
You can also adjust tint in the PICTURE menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Data Red : 0 ~ Green : 64
To adjust balance.
You can also adjust balance in the AUDIO menu.
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64(*transmit by Hexadecimal code)
*Refer to ‘Real data mapping1’. See page 92.
Acknowledgement [ j ][ ][Set ID][ ][OK/NG][Data][x]
*Refer to ‘Real data mapping1’. See page 92.
Acknowledgement [t][ ][Set ID][ ][OK/NG][Data][x]
11. Sharpness (Command2:k)
To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
*Refer to ‘Real data mapping1’. See page 92.
Acknowledgement [k][ ][Set ID][ ][OK/NG][Data][x]
12. OSD Select (Command2:l)
To select OSD (On Screen Display) on/off.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 0: OSD off
Data 1: OSD on
Acknowledgement [l][ ][Set ID][ ][OK/NG][Data][x]
* When setting “OSD - Off ”, every OSD doesn’t display
on screen.
17. Colour Temperature (Command2:u)
To adjust colour temperature.
You can also adjust colour temperature in the PICTURE
menu.
Transmission [k][u][ ][Set ID][ ][Data][Cr]
Data 0: Medium 1: Cool 2: Warm 3: User
Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]
18. Red Adjustment(Command:v)
To adjust red in colour temperature
Transmission [k][v][ ][Set ID][ ][Data][Cr]
Data Min:0 ~ Max:C8
*Refer to "Real data mapping 2". as shown below.
Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x]
19. Green Adjustment(Command:w)
13. Remote Control Lock Mode (Command2:m)
To lock the remote control and the front panel controls
on the set.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 0: Lock off
Data 1: Lock on
Acknowledgement [m][ ][Set ID][ ][OK/NG][Data][x]
To adjust green in colour temperature.
Transmission [k][w][ ][Set ID][][Data][Cr]
Data Min:0 ~ Max:C8
*Refer to "Real data mapping 2" as shown below
Acknowledgement [w][ ][Set ID][ ][OK/NG][Data][x]
20. Blue Adjustment(Command:$)
14. Treble (Command2:r)
*Refer to ‘Real data mapping1’. See page 92.
Acknowledgement [r][ ][Set ID][ ][OK/NG][Data][x]
15. Bass (Command2:s)
To adjust bass.
You can also adjust bass in the AUDIO menu.
Transmission [k][s][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64(*transmit by Hexadecimal code)
*Refer to ‘Real data mapping1’. See page 92.
Acknowledgement [s][ ][Set ID][ ][OK/NG][Data][x]
*Real data mapping 2
0 : -20
5 : -19
A : -18
APPENDIX
To adjust treble.
You can also adjust treble in the AUDIO menu.
Transmission [k][r][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64(*transmit by Hexadecimal code)
To adjust blue in colour temperature.
Transmission [k][$][ ][Set ID][ ][Data][Cr]
Data Min:0 ~ Max:C8
*Refer to "Real data mapping 2"as shown below
Acknowledgement [$][ ][Set ID][ ][OK/NG][Data][x]
5F: -1
64: 0
69: +1
C3 : +19
C8 : +20
93
APPENDIX
21. Channel Tuning (Command: m a)
To tune channel to following programme number
Transmission [m][a][ ][Set ID][ ][Data0][ ][Data1]
[ ][Data2][Cr]
Data 0: High channel data
Data 1: Low channel data
Data 2: 00: Analogue TV
: 10: Digital TV
ex) Analogue TV : ma 0 00 01 00
* Channel Data Range:
Analogue TV: 0 ~ 63
Digital TV: 0 ~ 3E
25. Orbiter Pixel Setting (Command2:s)
To adjust pixel number in orbiter function.
Transmission [ j ][s][ ][Set ID][ ][Data][Cr]
Data Min: 1~ Max: 3
*Refer to ‘Real data mapping1’. See page 92.
Acknowledgement [s][ ][Set ID][ ][OK/NG][Data][x]
26. Send IR Code (Command: m c)
To send IR remote key code
Transmission [m][c][ ][Set ID][ ][Data][Cr]
Data Key code: Refer to page 88.
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
22. ISM Method (Command2:p)
To control the ISM method. You can also adjust ISM
method in OPTION menu.
Transmission [ j ][p][ ][Set ID][ ][Data][Cr]
Data 0: Normal
Data 1: Orbiter
Data 2: Inversion
Data 3: White Wash
Acknowledgement [p][ ][Set ID][ ][OK/NG][Data][x]
23. Low Power (Command2:q)
To reduce the power consumption of the set. You can
also adjust Low power in OPTION menu.
Transmission [ j ][q][ ][Set ID][ ][Data][Cr]
Data 0: low power off
1: low power on
Acknowledgement [q][ ][Set ID][ ][OK/NG][Data][x]
24. Orbiter Time Setting (Command2:r)
APPENDIX
To adjust orbiter operation time term.
Transmission [ j ][r][ ][Set ID][ ][Data][Cr]
Data Min: 1~ Max: FE(*transmit by Hexadecimal code),
Unit: Second
*Refer to ‘Real data mapping1’. See page 92.
Acknowledgement [r][ ][Set ID][ ][OK/NG][Data][x]
94
27. Input Select(Command: x b)
To select input source for TV.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data 00 : Digital
Data 41 : Component2
Data 10 : Analogue
Data 50 : RGB-PC
Data 20 : AV1
Data 90 : HDMI1
Data 21 : AV2
Data 91 : HDMI2
Data 40 : Component1
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
OPEN SOURCE LICENSE
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU
General Public License is intended to guarantee your freedom to share and change free
software--to make sure the software is free for all its users. This General Public License applies to most of the Free
Software Foundation's software and to any other program whose authors commit to
using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public License
instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to
make sure that you have the freedom to distribute copies of free software (and charge for
this service if you wish), that you receive source code or can get it if you want it, that you can change the software or
use pieces of it in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software,
or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all
the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show
them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal
permission to copy, distribute and/or modify the software.
Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we
want its recipients to know that what they have is not the original, so that any problems introduced by others will not
reflect on the original authors' reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors
of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we
have made it clear that any patent must be licensed for everyone's free use or not licensed at all.
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it
may be distributed under the terms of this General Public License. The "Program", below, refers to any such program
or work, and a "work based on the Program" means either the Program or any derivative work under copyright law: that
is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into
another language. (Hereinafter, translation is included without limitation in the term "modification".) Each licensee is
addressed as "you".
APPENDIX
The precise terms and conditions for copying, distribution and modification follow.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope.
The act of running the Program is not restricted, and the output from the Program
is covered only if its contents constitute a work based on the Program (independent of having been made by running
the Program). Whether that is true depends on what the Program does.
95
APPENDIX
1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of
any warranty; and give any other recipients of the Program a copy of this License
along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in
exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the
Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you
also meet all of these conditions:
a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any
change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the
Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this
License.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running
for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may
redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception:
if the Program itself is interactive but does not normally print such an announcement, your work based on the
Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the
Program, and can be reasonably considered independent and separate works in themselves, then this License, and its
terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same
sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of
this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the
intent is to exercise the right to control the distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on
the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this
License.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable
form under the terms of Sections 1 and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under
the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,
APPENDIX
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than
your cost of physically performing source distribution, a complete machine-readable copy of the corresponding
source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software
interchange; or,
c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This
alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it. For an executable
work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary
form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs,
unless that component itself accompanies the executable.
96
If distribution of executable or object code is made by offering access to copy from a designated place, then offering
equivalent access to copy the source code from the same place counts as distribution of the source code, even though
third parties are not compelled to copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License.
Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate
your rights under this License. However, parties who have received copies, or rights, from you under this License will
not have their licenses terminated so long as such parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not ccept
this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate
your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the
Program or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a
license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You
may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible
for enforcing compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to
patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you
may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the
Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it
and this License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest
validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution
system, which is implemented by public license practices. Many people have made generous contributions to the wide
range of software distributed through that system in reliance on consistent application of that system; it is up to the
author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot
impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted
interfaces, the original copyright holder who places the Program under this License may add an explicit geographical
distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus
excluded. In such case, this License incorporates the limitation as if written in the body of this License.
Each version is given a distinguishing version number. If the Program specifies a version number of this License which
applies to it and "any later version", you have the option of following the terms and conditions either of that version or of
any later version published by the Free Software Foundation. If the Program does not specify a version number of
this License, you may choose any version ever published by the Free Software Foundation.
APPENDIX
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to
time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems
or concerns.
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different,
write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to
the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals
of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software
generally.
97
APPENDIX
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING
THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY
OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE
QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING
BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY
YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS),
EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to
achieve this is to make it free software which everyone can redistribute and change under these terms.
To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most
effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to
where the full notice is found.
<one line to give the program's name and a brief idea of what it does.>
Copyright (C) <year> <name of author>
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public
License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later
version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the
implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General
Public License for more details.
You should have received a copy of the GNU General Public License along with this program; if not, write to the
Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
Also add information on how to contact you by electronic and paper mail.
If the program is interactive, make it output a short notice like this when it starts in an interactive mode:
APPENDIX
Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w'. This is free software, and you are welcome to redistribute it under certain conditions;
type `show c' for details.
The hypothetical commands `show w' and `show c' should show the appropriate parts of the General Public License.
Of course, the commands you use may be called something other than `show w' and `show c'; they could even be
mouse-clicks or menu items--whatever suits your program.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer"
for the program, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program `Gnomovision' (which makes passes at compilers) written by James Hacker.
<signature of Ty Coon>, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating your program into proprietary programs. If your program is a
subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is
what you want to do, use the GNU Lesser General Public License instead of this License.
98
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301
USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not
allowed.
[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public
License, version 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU
General Public Licenses are intended to guarantee your freedom to share and change free software--to make sure the
software is free for all its users.
This license, the Lesser General Public License, applies to some specially designated software packages--typically
libraries--of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest
you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in
any particular case, based on the explanations below.
When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are
designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you
wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of
it in new free programs; and that you are informed that you can do these things.
To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to
surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the
library or if you modify it.
For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the
rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code
with the library, you must provide complete object files to the recipients, so that they can relink them with the library
after making changes to the library and recompiling it. And you must show them these terms so they know their rights.
We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which
gives you legal permission to copy, distribute and/or modify the library.
To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the
library is modified by someone else and passed on, the recipients should know that what they have is not the original
version, so that the original author's reputation will not be affected by problems that might be introduced by others.
Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a
company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder.
Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom
of use specified in this license.
Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license,
the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary
General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free
programs.
We call this license the "Lesser" General Public License because it does Less to protect the user's freedom than the
ordinary General Public License. It also provides other free software developers Less of an advantage over competing
non-free programs. These disadvantages are the reason we use the ordinary General Public License for many
libraries. However, the Lesser license provides advantages in certain special circumstances.
APPENDIX
When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits
such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more
lax criteria for linking other code with the library.
For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library,
so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more
frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to
gain by limiting the free library to free software only, so we use the Lesser General Public License.
In other cases, permission to use a particular library in non-free programs enables a greater number of people to use
a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many
more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.
99
APPENDIX
Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a
program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library.
The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a "work based on the library" and a "work that uses the library". The former contains code derived from
the library, whereas the latter must be combined with the library in order to run.
GNU LESSER GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License Agreement applies to any software library or other program which contains a notice placed by the
copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public
License (also called "this License"). Each licensee is addressed as "you".
A "library" means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables.
The "Library", below, refers to any such software library or work which has been distributed under these terms. A
"work based on the Library" means either the Library or any derivative work under copyright law: that is to say, a work
containing the Library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into
another language. (Hereinafter, translation is included without limitation in the term "modification".)
"Source code" for a work means the preferred form of the work for making modifications to it. For a library, complete
source code means all the source code for all modules it contains, plus any associated interface definition files, plus
the scripts used to control compilation and installation of the library.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope.
The act of running a program using the Library is not restricted, and output from such a program is covered only if its
contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether
that is true depends on what the Library does and what the program that uses the Library does.
1. You may copy and distribute verbatim copies of the Library's complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection
in exchange for a fee.
2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library,
and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all
of these conditions:
a) The modified work must itself be a software library.
b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of
any change.
APPENDIX
c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this
License.
d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program
that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good
faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates,
and performs whatever part of its purpose remains meaningful.
(For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of
the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function
must be optional: if the application does not supply it, the square root function must still compute square roots.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the
Library, and can be reasonably considered independent and separate works in themselves, then this License, and its
terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same
sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of
this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
100
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the
intent is to exercise the right to control the distribution of derivative or collective works based on the Library.
In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the
Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy
of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU
General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU
General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other
change in these notices.
Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License
applies to all subsequent copies and derivative works made from that copy.
This option is useful when you wish to copy part of the code of the Library into a program that is not a library.
4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a
medium customarily used for software interchange.
If distribution of object code is made by offering access to copy from a designated place, then offering equivalent
access to copy the source code from the same place satisfies the requirement to distribute the source code, even
though third parties are not compelled to copy the source along with the object code.
5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being
compiled or linked with it, is called a "work that uses the Library". Such a work, in isolation, is not a derivative work of
the Library, and therefore falls outside the scope of this License.
However, linking a "work that uses the Library" with the Library creates an executable that is a derivative of the Library
(because it contains portions of the Library), rather than a "work that uses the library". The executable is therefore covered by this License. Section 6 states terms for distribution of such executables.
When a "work that uses the Library" uses material from a header file that is part of the Library, the object code for the
work may be a derivative work of the Library even though the source code is not.
Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library.
The threshold for this to be true is not precisely defined by law.
If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and
small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it
is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under
Section 6.)
Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of
Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with
the Library itself.
You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its
use are covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the
user to the copy of this License. Also, you must do one of these things:
APPENDIX
6. As an exception to the Sections above, you may also combine or link a "work that uses the Library" with the Library
to produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that
the terms permit modification of the work for the customer's own use and reverse engineering for debugging such modifications.
a) Accompany the work with the complete corresponding machine-readable source code for the Library including
whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work
is an executable linked with the Library, with the complete machine-readable "work that uses the Library", as object
code and/or source code, so that the user can modify the Library and then relink to produce a modified executable
containing the modified Library. (It is understood that the user who changes the contents of definitions files in the
Library will not necessarily be able to recompile the application to use the modified definitions.)
b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at
run time a copy of the library already present on the user's computer system, rather than copying library functions
into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as
long as the modified version is interface-compatible with the version that the work was made with.
101
APPENDIX
c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials
specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution.
d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to
copy the above specified materials from the same place.
e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy.
For an executable, the required form of the "work that uses the Library" must include any data and utility programs
needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need
not include anything that is normally distributed (in either source or binary form) with the major components (compiler,
kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies
the executable.
It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in
an executable that you distribute.
7. You may place library facilities that are a work based on the Library side-by-side in a single library together with
other library facilities not covered by this License, and distribute such a combined library, provided that the separate
distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided that
you do these two things:
a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other
library facilities. This must be distributed under the terms of the Sections above.
b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and
explaining where to find the accompanying uncombined form of the same work.
8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this
License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under
this License will not have their licenses terminated so long as such parties remain in full compliance.
9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept
this License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your
acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or
works based on it.
10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a
license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein.
You are not responsible for enforcing compliance by third parties with this License.
APPENDIX
11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to
patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you
may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the
Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and
this License would be to refrain entirely from distribution of the Library.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest
validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution
system which is implemented by public license practices. Many people have made generous contributions to the wide
range of software distributed through that system in reliance on consistent application of that system; it is up to the
author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot
impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted
interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus
excluded. In such case, this License incorporates the limitation as if written in the body of this License.
102
13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License
from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address
new problems or concerns.
Each version is given a distinguishing version number. If the Library specifies a version number of this License which
applies to it and "any later version", you have the option of following the terms and conditions either of that version or of
any later version published by the Free Software Foundation. If the Library does not specify a license version number,
you may choose any version ever published by the Free Software Foundation.
14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software
Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing
and reuse of software generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY,
TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE
COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY "AS IS" WITHOUT WARRANTY OF
ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY
AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU
ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT
NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU
OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF
SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Libraries
If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it
free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms
(or, alternatively, under the terms of the ordinary General Public License).
To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source
file to most effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a
pointer to where the full notice is found.
<one line to give the library's name and a brief idea of what it does.>
Copyright (C) <year> <name of author>
This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied
warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General
Public License for more details.
APPENDIX
This library is free software; you can redistribute it and/or
modify it under the terms of the GNU Lesser General
Public License as published by the Free Software Foundation; either version 2.1 of the License, or (at your option)
any later version.
You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to
the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Also add information on how to contact you by electronic and paper mail.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer"
for the library, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob' (a library for tweaking knobs) written by
James Random Hacker.
<signature of Ty Coon>, 1 April 1990
Ty Coon, President of Vice
103
APPENDIX
MOZILLA PUBLIC LICENSE
Version 1.1
--------------1. Definitions.
1.0.1. "Commercial Use" means distribution or otherwise making the Covered Code available to a third party.
1.1. "Contributor" means each entity that creates or contributes to the creation of Modifications.
1.2. "Contributor Version" means the combination of the Original Code, prior Modifications used by a Contributor,
and the Modifications made by that particular Contributor.
1.3. "Covered Code" means the Original Code or Modifications or the combination of the Original Code and
Modifications, in each case including portions thereof.
1.4. "Electronic Distribution Mechanism" means a mechanism generally accepted in the software development community for the electronic transfer of data.
1.5. "Executable" means Covered Code in any form other than Source Code.
1.6. "Initial Developer" means the individual or entity identified as the Initial Developer in the Source Code notice
required by Exhibit A.
1.7. "Larger Work" means a work which combines Covered Code or portions thereof with code not governed by the
terms of this License.
1.8. "License" means this document.
1.8.1. "Licensable" means having the right to grant, to the maximum extent possible, whether at the time of the initial grant or subsequently acquired, any and all of the rights conveyed herein.
1.9. "Modifications" means any addition to or deletion from the substance or structure of either the Original Code or
any previous Modifications. When Covered Code is released as a series of files, a Modification is:
A. Any addition to or deletion from the contents of a file containing Original Code or previous Modifications.
B. Any new file that contains any part of the Original Code or previous Modifications.
1.10. "Original Code" means Source Code of computer software code which is described in the Source Code notice
required by Exhibit A as Original Code, and which, at the time of its release under this License is not already
Covered Code governed by this License.
1.10.1. "Patent Claims" means any patent claim(s), now owned or hereafter acquired, including without limitation,
method, process, and apparatus claims, in any patent Licensable by grantor.
APPENDIX
1.11. "Source Code" means the preferred form of the Covered Code for making modifications to it, including all
modules it contains, plus any associated interface definition files, scripts used to control compilation and installation
of an Executable, or source code differential comparisons against either the Original Code or another well known,
available Covered Code of the Contributor's choice. The Source Code can be in a compressed or archival form,
provided the appropriate decompression or de-archiving software is widely available for no charge.
1.12. "You" (or "Your") means an individual or a legal entity exercising rights under, and complying with all of the
terms of, this License or a future version of this License issued under Section 6.1.
For legal entities, "You" includes any entity which controls, is controlled by, or is under common control with You.
For purposes of this definition, "control" means (a) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (b) ownership of more than fifty percent (50%) of the outstanding shares or beneficial ownership of such entity.
2. Source Code License.
2.1. The Initial Developer Grant.
The Initial Developer hereby grants You a world-wide, royalty-free, non-exclusive license, subject to third party intellectual property claims:
(a) under intellectual property rights (other than patent or trademark) Licensable by Initial Developer to use,
reproduce, modify, display, perform, sublicense and distribute the Original Code (or portions thereof) with or
without Modifications, and/or as part of a Larger Work; and
104
(b) under Patents Claims infringed by the making, using or selling of Original Code, to make, have made, use,
practice, sell, and offer for sale, and/or otherwise dispose of the Original Code (or portions thereof).
(c) the licenses granted in this Section 2.1(a) and (b) are effective on the date Initial Developer first distributes
Original Code under the terms of this License.
(d) Notwithstanding Section 2.1(b) above, no patent license is granted: 1) for code that You delete from the
Original Code; 2) separate from the Original Code; or 3) for infringements caused by: i) the modification of the
Original Code or ii) the combination of the Original Code with other software or devices.
2.2. Contributor Grant.
Subject to third party intellectual property claims, each Contributor hereby grants You a world-wide, royalty-free,
non-exclusive license
(a) under intellectual property rights (other than patent or trademark) Licensable by Contributor, to use, reproduce, modify, display, perform, sublicense and distribute the Modifications created by such Contributor (or portions thereof) either on an unmodified basis, with other Modifications, as Covered Code and/or as part of a
Larger Work; and
(b) under Patent Claims infringed by the making, using, or selling of Modifications made by that Contributor
either alone and/or in combination with its Contributor Version (or portions of such combination), to make, use,
sell, offer for sale, have made, and/or otherwise dispose of: 1) Modifications made by that Contributor (or portions
thereof); and 2) the combination of Modifications made by that Contributor with its Contributor Version (or portions of such combination).
(c) the licenses granted in Sections 2.2(a) and 2.2(b) are effective on the date Contributor first makes
Commercial Use of the Covered Code.
(d) Notwithstanding Section 2.2(b) above, no patent license is granted: 1) for any code that Contributor has deleted from the Contributor Version; 2) separate from the Contributor Version; 3) for infringements caused by: i)
third party modifications of Contributor Version or ii) the combination of Modifications made by that Contributor
with other software (except as part of the Contributor Version) or other devices; or 4) under Patent Claims
infringed by Covered Code in the absence of Modifications made by that Contributor.
3. Distribution Obligations.
3.1. Application of License.
The Modifications which You create or to which You contribute are governed by the terms of this License, including
without limitation Section 2.2. The Source Code version of Covered Code may be distributed only under the terms of
this License or a future version of this License released under Section 6.1, and You must include a copy of this
License with every copy of the Source Code You distribute. You may not offer or impose any terms on any Source
Code version that alters or restricts the applicable version of this License or the recipients' rights hereunder.
However, You may include an additional document offering the additional rights described in Section 3.5.
3.3. Description of Modifications.
You must cause all Covered Code to which You contribute to contain a file documenting the changes You made to
create that Covered Code and the date of any change. You must include a prominent statement that the Modification
is derived, directly or indirectly, from Original Code provided by the Initial Developer and including the name of the
Initial Developer in (a) the Source Code, and (b) in any notice in an Executable version or related documentation in
which You describe the origin or ownership of the Covered Code.
APPENDIX
3.2. Availability of Source Code.
Any Modification which You create or to which You contribute must be made available in Source Code form under
the terms of this License either on the same media as an Executable version or via an accepted Electronic
Distribution Mechanism to anyone to whom you made an Executable version available; and if made available via
Electronic Distribution Mechanism, must remain available for at least twelve (12) months after the date it initially
became available, or at least six (6) months after a subsequent version of that particular Modification has been
made available to such recipients. You are responsible for ensuring that the Source Code version remains available
even if the
Electronic Distribution Mechanism is maintained by a third party.
3.4. Intellectual Property Matters
(a) Third Party Claims.
If Contributor has knowledge that a license under a third party's intellectual property rights is required to exercise
the rights granted by such Contributor under Sections 2.1 or 2.2, Contributor must include a text file with the
Source Code distribution titled "LEGAL" which describes the claim and the party making the claim in sufficient
detail that a recipient will know whom to contact. If Contributor obtains such knowledge after the Modification is
made available as described in Section 3.2, Contributor shall promptly modify the LEGAL file in all copies
Contributor makes available thereafter and shall take other steps (such as notifying appropriate mailing lists or
newsgroups) reasonably calculated to inform those who received the Covered Code that new knowledge has
been obtained.
105
APPENDIX
(b) Contributor APIs.
If Contributor's Modifications include an application programming interface and Contributor has knowledge of
patent licenses which are reasonably necessary to implement that API, Contributor must also include this information in the LEGAL file.
(c) Representations.
Contributor represents that, except as disclosed pursuant to Section 3.4(a) above, Contributor believes that
Contributor's Modifications are Contributor's original creation(s) and/or Contributor has sufficient rights to grant
the rights conveyed by this License.
3.5. Required Notices.
You must duplicate the notice in Exhibit A in each file of the Source Code. If it is not possible to put such notice in a
particular Source Code file due to its structure, then You must include such notice in a location (such as a relevant
directory) where a user would be likely to look for such a notice. If You created one or more Modification(s)
You may add your name as a Contributor to the notice described in Exhibit A. You must also duplicate this License
in any documentation for the Source Code where You describe recipients' rights or ownership rights relating to
Covered Code. You may choose to offer, and to charge a fee for, warranty, support, indemnity or liability obligations
to one or more recipients of Covered Code. However, You may do so only on Your own behalf, and not on behalf of
the Initial
Developer or any Contributor. You must make it absolutely clear than any such warranty, support, indemnity or liability obligation is offered by You alone, and You hereby agree to indemnify the Initial Developer and every Contributor
for any liability incurred by the Initial Developer or such Contributor as a result of warranty, support, indemnity or liability terms You offer.
3.6. Distribution of Executable Versions.
You may distribute Covered Code in Executable form only if the requirements of Section 3.1-3.5 have been met for
that Covered Code, and if You include a notice stating that the Source Code version of the Covered Code is available under the terms of this License, including a description of how and where You have fulfilled the obligations of
Section 3.2. The notice must be conspicuously included in any notice in an Executable version, related documentation or collateral in which You describe recipients' rights relating to the Covered Code. You may distribute the
Executable version of Covered Code or ownership rights under a license of Your choice, which may contain terms
different from this License, provided that You are in compliance with the terms of this License and that the license
for the Executable version does not attempt to limit or alter the recipient's rights in the Source Code version from
the rights set forth in this
License. If You distribute the Executable version under a different license You must make it absolutely clear that any
terms which differ from this License are offered by You alone, not by the Initial Developer or any Contributor. You
hereby agree to indemnify the Initial Developer and every Contributor for any liability incurred by the Initial
Developer or such Contributor as a result of any such terms You offer.
3.7. Larger Works.
You may create a Larger Work by combining Covered Code with other code not governed by the terms of this
License and distribute the Larger Work as a single product. In such a case, You must make sure the requirements
of this License are fulfilled for the Covered Code.
4. Inability to Comply Due to Statute or Regulation.
APPENDIX
If it is impossible for You to comply with any of the terms of this License with respect to some or all of the Covered
Code due to statute, judicial order, or regulation then You must: (a) comply with the terms of this License to the maximum extent possible; and (b) describe the limitations and the code they affect. Such description must be included in
the LEGAL file described in Section 3.4 and must be included with all distributions of the Source Code. Except to
the
extent prohibited by statute or regulation, such description must be sufficiently detailed for a recipient of ordinary
skill to be able to understand it.
5. Application of this License.
This License applies to code to which the Initial Developer has attached the notice in Exhibit A and to related
Covered Code.
6. Versions of the License.
6.1. New Versions.
Netscape Communications Corporation ("Netscape") may publish revised and/or new versions of the License from
time to time. Each version will be given a distinguishing version number.
6.2. Effect of New Versions.
Once Covered Code has been published under a particular version of the License, You may always continue to use
it under the terms of that version. You may also choose to use such Covered Code under the terms of any subsequent version of the License published by Netscape. No one other than Netscape has the right to modify the terms
applicable to Covered Code created under this License.
106
6.3. Derivative Works.
If You create or use a modified version of this License (which you may only do in order to apply it to code which is
not already Covered Code governed by this License), You must (a) rename Your license so that the phrases
"Mozilla", "MOZILLAPL", "MOZPL", "Netscape", "MPL", "NPL" or any confusingly similar phrase do not appear in
your license (except to note that your license differs from this License) and (b) otherwise make it clear that Your version of the license contains terms which differ from the Mozilla Public License and Netscape Public License. (Filling
in the name of the Initial Developer, Original Code or Contributor in the notice described in Exhibit A shall not of
themselves be deemed to be modifications of this License.)
7. DISCLAIMER OF WARRANTY.
COVERED CODE IS PROVIDED UNDER THIS LICENSE ON AN "AS IS" BASIS, WITHOUT WARRANTY OF ANY
KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, WARRANTIES THAT THE COVERED CODE IS FREE OF DEFECTS, MERCHANTABLE, FIT FOR A PARTICULAR PURPOSE OR NON-INFRINGING. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE COVERED CODE IS WITH YOU.
SHOULD ANY COVERED CODE PROVE DEFECTIVE IN ANY RESPECT, YOU (NOT THE INITIAL DEVELOPER OR
ANY OTHER CONTRIBUTOR) ASSUME THE COST OF ANY NECESSARY SERVICING, REPAIR OR CORRECTION.
THIS DISCLAIMER OF WARRANTY CONSTITUTES AN ESSENTIAL PART OF THIS LICENSE. NO USE OF ANY
COVERED CODE IS AUTHORIZED HEREUNDER EXCEPT UNDER THIS DISCLAIMER.
8. TERMINATION.
8.1. This License and the rights granted hereunder will terminate automatically if You fail to comply with terms herein and fail to cure such breach within 30 days of becoming aware of the breach. All sublicenses to the Covered
Code which are properly granted shall survive any termination of this License. Provisions which, by their nature,
must remain in effect beyond the termination of this License shall survive.
8.2. If You initiate litigation by asserting a patent infringement claim (excluding declatory judgment actions) against
Initial Developer or a Contributor (the Initial Developer or Contributor against whom You file such action is referred
to as "Participant") alleging that:
(a) such Participant's Contributor Version directly or indirectly infringes any patent, then any and all rights granted
by such Participant to You under Sections 2.1 and/or 2.2 of this License shall, upon 60 days notice from Participant
terminate prospectively, unless if within 60 days after receipt of notice You either: (i) agree in writing to pay
Participant a mutually agreeable reasonable royalty for Your past and future use of Modifications made by such
Participant, or (ii) withdraw Your litigation claim with respect to the Contributor Version against such Participant. If
within 60 days of notice, a reasonable royalty and payment arrangement are not mutually agreed upon in writing by
the parties or the litigation claim is not withdrawn, the rights granted by Participant to You under Sections 2.1 and/or
2.2 automatically terminate at the expiration of the 60 day notice period specified above.
(b) any software, hardware, or device, other than such Participant's Contributor Version, directly or indirectly
infringes any patent, then any rights granted to You by such Participant under Sections 2.1(b) and 2.2(b) are
revoked effective as of the date You first made, used, sold, distributed, or had made, Modifications made by that
Participant.
8.3. If You assert a patent infringement claim against Participant alleging that such Participant's Contributor Version
directly or indirectly infringes any patent where such claim is resolved (such as by license or settlement) prior to the
initiation of patent infringement litigation, then the reasonable value of the licenses granted by such Participant
under Sections 2.1 or 2.2 shall be taken into account in determining the amount or value of any payment or license.
9. LIMITATION OF LIABILITY.
APPENDIX
8.4. In the event of termination under Sections 8.1 or 8.2 above, all end user license agreements (excluding distributors and resellers) which have been validly granted by You or any distributor hereunder prior to termination shall
survive termination.
UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL THEORY, WHETHER TORT (INCLUDING NEGLIGENCE), CONTRACT, OR OTHERWISE, SHALL YOU, THE INITIAL DEVELOPER, ANY OTHER CONTRIBUTOR, OR
ANY DISTRIBUTOR OF COVERED CODE,OR ANY SUPPLIER OF ANY OF SUCH PARTIES, BE LIABLE TO ANY
PERSON FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY CHARACTER
INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF GOODWILL, WORK STOPPAGE, COMPUTER
FAILURE OR MALFUNCTION, OR ANY AND ALL OTHER COMMERCIAL DAMAGES OR LOSSES, EVEN IF SUCH
PARTY SHALL HAVE BEEN INFORMED OF THE POSSIBILITY OF SUCH DAMAGES. THIS LIMITATION OF LIABILITY SHALL NOT APPLY TO LIABILITY FOR DEATH OR PERSONAL INJURY RESULTING FROM SUCH PARTY'S
NEGLIGENCE TO THE EXTENT APPLICABLE LAW PROHIBITS SUCH LIMITATION. SOME JURISDICTIONS DO
NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THIS
EXCLUSION AND LIMITATION MAY NOT APPLY TO YOU.
107
APPENDIX
10. U.S. GOVERNMENT END USERS.
The Covered Code is a "commercial item," as that term is defined in 48 C.F.R. 2.101 (Oct. 1995), consisting of
"commercial computer software" and "commercial computer software documentation," as such terms are used in 48
C.F.R. 12.212 (Sept. 1995). Consistent with 48 C.F.R. 12.212 and 48 C.F.R. 227.7202-1 through 227.7202-4 (June
1995), all U.S. Government End Users acquire Covered Code with only those rights set forth herein.
11. MISCELLANEOUS.
This License represents the complete agreement concerning subject matter hereof. If any provision of this License
is held to be unenforceable, such provision shall be reformed only to the extent necessary to make it enforceable. This
License shall be governed by California law provisions (except to the extent applicable law, if any, provides otherwise),
excluding its conflict-of-law provisions. With respect to disputes in which at least one party is a citizen of, or an entity
chartered or registered to do business in the United States of America, any litigation relating to this License shall be
subject to the jurisdiction of the Federal Courts of the Northern District of California, with venue lying in Santa Clara
County, California, with the losing party responsible for costs, including without limitation, court costs and reasonable
attorneys' fees and expenses. The application of the United Nations Convention on Contracts for the International Sale
of Goods is expressly excluded. Any law or regulation which provides that the language of a contract shall be construed
against the drafter shall not apply to this License.
12. RESPONSIBILITY FOR CLAIMS.
As between Initial Developer and the Contributors, each party is responsible for claims and damages arising, directly or indirectly, out of its utilization of rights under this License and You agree to work with Initial Developer and
Contributors to distribute such responsibility on an equitable basis. Nothing herein is intended or shall be deemed to
constitute any admission of liability.
13. MULTIPLE-LICENSED CODE.
Initial Developer may designate portions of the Covered Code as "Multiple-Licensed". "Multiple-Licensed" means
that the Initial Developer permits you to utilize portions of the Covered Code under Your choice of the NPL or the alternative licenses, if any, specified by the Initial Developer in the file described in Exhibit A.
EXHIBIT A -Mozilla Public License.
``The contents of this file are subject to the Mozilla Public License Version 1.1 (the "License"); you may not use this
file except in compliance with the License. You may obtain a copy of the License at http://www.mozilla.org/MPL/
Software distributed under the License is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY KIND,
either express or implied. See the License for the specific language governing rights and limitations under the License.
The Original Code is ______________________________________.
The Initial Developer of the Original Code is ________________________.
Portions created by ______________________ are Copyright (C) ______
_______________________. All Rights Reserved.
APPENDIX
Contributor(s): ______________________________________.
Alternatively, the contents of this file may be used under the terms of the _____ license (the "[___] License"), in
which case the provisions of [______] License are applicable instead of those above. If you wish to allow use of your
version of this file only under the terms of the [____] License and not to allow others to use your version of this file
under the MPL, indicate your decision by deleting the provisions above and replace them with the notice and other
provisions required by the [___] License. If you do not delete the provisions above, a recipient may use your version of
this file under either the MPL or the [___] License."
[NOTE: The text of this Exhibit A may differ slightly from the text of the notices in the Source Code files of the
Original Code. You should use the text of this Exhibit A rather than the text found in the Original Code Source Code for
Your Modifications.]
108
Download PDF