LG | 55EA9800 | LG 55EA9800 Owner’s Manual

OWNER’S MANUAL
Please read this manual carefully before operating your set and retain it
for future reference.
EA98**
P/NO :MFL67881932 (1306-REV00)
Printed in Korea
www.lg.com
2
TABLE OF CONTENTS
ENG
ENGLISH
TABLE OF CONTENTS
3
Safety Instructions
8
- Viewing 3D Imaging (Only 3D models)
10
INSTALLATION PROCEDURE
10
ASSEMBLING AND PREPARING
10
13
14
15
16
17
17
17
18
19
Unpacking
Separate purchase
Parts and buttons
Using the Smart Touch Button
Lifting and moving the TV
Setting up the TV
- Assembling the AV cover
Mounting on a table
- Securing the TV to a table
Tidying cables
19
Video Call Camera
20
20
Overview
Attaching the video call camera
21
MAKING CONNECTIONS
22
22
23
23
24
24
24
25
25
26
Antenna connection
HDMI connection
DVI to HDMI connection
Component connection
Composite connection
Audio connection
- Digital optical audio connection
Headphone connection
USB connection
MHL connection
27
REMOTE CONTROL
29
MAGIC REMOTE CONTROL
FUNCTIONS
30
30
30
Registering Magic Remote Control
How to use Magic Remote Control
Precautions to Take when Using the Magic
Remote Control
31
Using the User guide
32
MAINTENANCE
32
32
32
Cleaning Your TV
- Screen, frame, cabinet and stand
- Power cord
33
TROUBLESHOOTING
34
Environmental Information
34
WEEE
35
SPECIFICATIONS
40
LICENSES
40
OPEN SOURCE SOFTWARE NOTICE
40
External control device
setup
WARNING
yy If you ignore the warning message, you may
be seriously injured or there is a possibility of
accident or death.
CAUTION
yy If you ignore the caution message, you may be
slightly injured or the product may be damaged.
NOTE
yy The note helps you understand and use the
product safely. Please read the note carefully
before using the product.
SAFETY INSTRUCTIONS
ENGLISH
ENG
Safety Instructions
Please read these safety precautions carefully before using the product.
WARNING
yyDo not place the TV and/or
remote control in the following
environments:
--A l o c a t i o n e x p o s e d t o
direct sunlight
--An area with high humidity
such as a bathroom
--Near any heat source
such as stoves and other
devices that produce heat
--Near kitchen counters or
humidifiers where they
can easily be exposed to
steam or oil
--An area exposed to rain
or wind
--Near containers of water
such as vases
Otherwise, this may result in
fire, electric shock, malfunction
or product deformation.
yyDo not place the product
where it might be exposed
to dust.
This may cause a fire hazard.
yyMains Plug is the TV connecting/disconnecting device
to AC mains electric supply.
This plug must remain readily
attached and operable when
TV is in use.
yyDo not touch the power plug
with wet hands. Additionally, if the cord pin is wet or
covered with dust, dry the
power plug completely or
wipe dust off.
You may be electrocuted due
to excess moisture.
yyMake sure to connect Mains
cable to compliant AC mains
socket with Grounded earth
pin. (Except for devices
which are not grounded on
earth.) Otherwise possibility you may be electrocuted
or injured.
3
yyInsert power cable plug
completely into wall socket
otherwise if not secured
completely into socket, fire
ignition may break out.
yyEnsure the power cord does
not come into contact with
hot objects such as a heater.
This may cause a fire or an
electric shock hazard.
yyDo not place a heavy object,
or the product itself, on
power cables.
Otherwise, this may result in
fire or electric shock.
yyBend antenna cable between
inside and outside building to
prevent rain from flowing in.
This may cause water damaged inside the Product and
could give an electric shock.
yyWhen mounting TV onto wall
make sure to neatly install
and isolate cabling from rear
of TV as to not create possibility of electric shock /fire
hazard.
yyDo not plug too many electrical devices into a single
multiple electrical outlet.
Otherwise, this may result in
fire due to over-heating.
yyDo not drop the product or let
it fall over when connecting
external devices.
Otherwise, this may result
in injury or damage to the
product.
4
SAFETY INSTRUCTIONS
ENG
ENGLISH
yyKeep the packing antimoisture material or vinyl
packing out of the reach of
children.
Anti-moisture material is
harmful if swallowed. If
swallowed by mistake, force
the patient to vomit and
visit the nearest hospital.
Additionally, vinyl packing can
cause suffocation. Keep it out
of the reach of children.
yyDo not let your children climb
or cling onto the TV.
Otherwise, the TV may
fall over, which may cause
serious injury.
yyDispose of used batteries
carefully to ensure that a
small child does not consume
them.
Please seek Doctor- Medical
Attention immediately if child
consumes batteries.
yyDo not insert any metal
objects/conductors (like
a metal chopstick/cutlery/
screwdriver) between power
cable plug and input Wall
Socket while it is connected
to the input terminal on the
wall. Additionally, do not
touch the power cable right
after plugging into the wall
input terminal.
You may be electrocuted.
(Depending on model)
yyDo not put or store inflammable substances near the
product. There is a danger of
combustion/explosion or fire
due to careless handling of
the inflammable substances.
yyDo not drop metallic objects
such as coins, hair pins,
chopsticks or wire into the
product, or inflammable
objects such as paper and
matches. Children must pay
particular attention.
Electrical shock, fire or injury
can occur. If a foreign object
is dropped into the product,
unplug the power cord and
contact the service centre.
yyDo not spray water on the
product or scrub with an
inflammable substance
(thinner or benzene). Fire or
electric shock accident can
occur.
yyDo not allow any impact,
shock or any objects to fall
into the unit, and do not drop
anything onto the screen. You
may be injured or the product
can be damaged.
yyNever touch this product or
antenna during a thunder or
lighting storm.
You may be electrocuted.
yyNever touch the wall outlet
when there is leakage of
gas, open the windows and
ventilate.
It may cause a fire or a burn
by a spark.
yyDo not disassemble, repair
or modify the product at your
own discretion.
Fire or electric shock accident can occur.
Contact the service centre for
check, calibration or repair.
yyIf any of the following occur,
unplug the product immediately and contact your local
service centre.
--The product has been
impacted by shock
--The product has been
damaged
--Foreign objects have
entered the product
--The product produced
smoke or a strange smell
This may result in fire or electric shock.
SAFETY INSTRUCTIONS
yyApparatus shall not be exposed to dripping or splashing and no objects filled with
liquids, such as vases, shall
be placed on the apparatus.
CAUTION
yyWhen installing the antenna,
consult with a qualified service technician. If not installed
by a qualified technician, this
may create a fire hazard or
an electric shock hazard.
yyWe recommend that you
maintain a distance of
at least 2 to 7 times the
diagonal screen size when
watching TV.
If you watch TV for a long period of time, this may cause
blurred vision.
yyOnly use the specified type
of battery.
This could cause damage to
the remote control.
yyInstall the product where no
radio wave occurs.
yyThere should be enough
distance between an outside
antenna and power lines to
keep the former from touching the latter even when the
antenna falls.
This may cause an electric
shock.
yyDo not install the product
on places such as unstable
shelves or inclined surfaces.
Also avoid places where
there is vibration or where
the product cannot be fully
supported.
Otherwise, the product may
fall or flip over, which may
cause injury or damage to
the product.
yyIf you install the TV on a
stand, you need to take actions to prevent the product
from overturning. Otherwise,
the product may fall over,
which may cause injury.
yyIf you intend to mount the product to a wall, attach
VESA standard mounting interface (optional parts)
to the back of the product. When you install the set
to use the wall mounting bracket (optional parts),
fix it carefully so as not to drop.
yyOnly use the attachments / accessories specified
by the manufacturer.
yyDo not mix new batteries with
old batteries.
This may cause the batteries
to overheat and leak.
yyBatteries should not be exposed to excessive
heat. For example, keep away from direct Sunlight, open fireplace and electric heaters.
yyDo not place non-rechargeable batteries in charging device.
yyMake sure there are no
objects between the remote
control and its sensor.
yySignal from Remote Control
can be interrupted due to
external/internal lighting eg
Sunlight, fluorescent lighting.
If this occurs turn off lighting
or darken viewing area.
yyWhen connecting external
devices such as video game
consoles, make sure the
connecting cables are long
enough.
Otherwise, the product may
fall over, which may cause
injury or damage the product.
yyDo not turn the product On/
Off by plugging-in or unplugging the power plug to the
wall outlet. (Do not use the
power plug for switch.)
It may cause mechanical failure or could give an electric
shock.
ENGLISH
ENG
yyUnplug the TV from AC
mains wall socket if you do
not intend to use the TV for a
long period of time. Accumulated dust can cause fire
hazard and insulation deterioration can cause electric
leakage/shock/fire.
5
6
SAFETY INSTRUCTIONS
ENG
ENGLISH
yyPlease follow the installation
instructions below to prevent
the product from overheating.
--The distance between
the product and the wall
should be more than
10 cm.
--Do not install the product
in a place with no ventilation (e.g., on a bookshelf
or in a cupboard).
--Do not install the product
on a carpet or cushion.
--Make sure the air vent is
not blocked by a tablecloth
or curtain.
Otherwise, this may result in
fire.
yyTake care not to touch the
ventilation openings when
watching the TV for long
periods as the ventilation
openings may become hot.
This does not affect the
operation or performance of
the product.
yyPeriodically examine the cord of your appliance,
and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact
replacement part by an authorized servicer.
yyPrevent dust collecting on the
power plug pins or outlet.
This may cause a fire hazard.
yyProtect the power cord from
physical or mechanical
abuse, such as being twisted,
kinked, pinched, closed in a
door, or walked upon. Pay
particular attention to plugs,
wall outlets, and the point
where the cord exits the appliance.
yyDo not press strongly upon
the panel with a hand or
sharp object such as nail,
pencil or pen, or make a
scratch on it, as it may
cause damage to screen.
yyAvoid touching the screen or
holding your finger(s) against
it for long periods of time.
Doing so may produce some
temporary or permanent distortion/damage to screen.
yyWhen cleaning the product
and its components, unplug
the power first and wipe it
with a soft cloth. Applying
excessive force may cause
scratches or discolouration.
Do not spray with water or
wipe with a wet cloth. Never
use glass cleaner, car or
industrial shiner, abrasives
or wax, benzene, alcohol
etc., which can damage the
product and its panel.
Otherwise, this may result in
fire, electric shock or product
damage (deformation, corrosion or breakage).
yyAs long as this unit is connected to the AC wall
outlet, it is not disconnected from the AC power
source even if you turn off this unit by SWITCH.
yyWhen unplugging the cable,
grab the plug and unplug it,
by pulling at the plug. Don’t
pull at the cord to unplug the
power cord from the power
board, as this could be hazardous.
yyWhen moving the product,
make sure you turn the
power off first. Then, unplug
the power cables, antenna
cables and all connecting
cables.
The TV set or power cord
may be damaged, which may
create a fire hazard or cause
electric shock.
yyWhen moving or unpacking
the product, work in pairs because the product is heavy.
Otherwise, this may result in
injury.
SAFETY INSTRUCTIONS
yyRefer all servicing to qualified
service personnel. Servicing
is required when the apparatus has been damaged
in any way, such as power
supply cord or plug is damaged, liquid has been spilled
or objects have fallen into
the apparatus, the apparatus
has been exposed to rain or
moisture, does not operate normally, or has been
dropped.
yyIf the product feels cold to the
touch, there may be a small
“flicker” when it is turned on.
This is normal, there is nothing wrong with product.
yyThe panel is a high technology display product with
resolution of two million to six
million pixels. You may see
tiny black dots and/or brightly
coloured dots (red, blue or
green) at a size of 1 ppm on
the panel. This does not indicate a malfunction and does
not affect the performance
and reliability of the product.
This phenomenon also occurs in third-party products
and is not subject to exchange or refund.
yyYou may find different brightness and colour of the panel
depending on your viewing
position(left/right/top/down).
This phenomenon occurs due
to the characteristic of the
panel. It is not related with
the product performance, and
it is not malfunction.
ENGLISH
ENG
yyContact the service centre
once a year to clean the
internal parts of the product.
7
yyDisplaying a still image (e.g., broadcasting channel logo, on-screen menu, scene from a video
game or computer screen) for a prolonged time
may cause damage to the screen, resulting in
retention of the image, which is known as image
sticking. It can remain for long time or never disappear. The warranty does not cover the product
for image sticking.
Avoid displaying a fixed image on your television’s screen for a prolonged period (1 or more
hours for OLED).
Also, if you watch the TV at a ratio of 4:3 for
a long time, image sticking may occur on the
borders of the panel.
This phenomenon also occurs in third-party products and is not subject to exchange or refund.
yyGenerated Sound
“Cracking” noise: A cracking noise that occurs
when watching or turning off the TV is generated
by plastic thermal contraction due to temperature and humidity. This noise is common for
products where thermal deformation is required.
Electrical circuit humming/panel buzzing: A
low level noise is generated from a high-speed
switching circuit, which supplies a large amount
of current to operate a product. It varies depending on the product.
This generated sound does not affect the performance and reliability of the product.
8
SAFETY INSTRUCTIONS
ENG
ENGLISH
Viewing 3D Imaging (Only 3D models)
WARNING
Viewing Environment
yy Viewing Time
-- When watching 3D contents, take 5 - 15 minute breaks every hour. Viewing 3D contents for a long
period of time may cause headache, dizziness, fatigue or eye strain.
Those that have a photosensitive seizure or chronic illness
yy Some users may experience a seizure or other abnormal symptoms when they are exposed to a
flashing light or particular pattern from 3D contents.
yy Do not watch 3D videos if you feel nausea, are pregnant and/ or have a chronic illness such as epilepsy,
cardiac disorder, or blood pressure disease, etc.
yy 3D Contents are not recommended to those who suffer from stereo blindness or stereo anomaly.
Double images or discomfort in viewing may be experienced.
yy If you have strabismus (cross-eyed), amblyopia (weak eyesight) or astigmatism, you may have trouble
sensing depth and easily feel fatigue due to double images. It is advised to take frequent breaks than
the average adult.
yy If your eyesight varies between your right and left eye, revise your eyesight prior to watching 3D
contents.
Symptoms which require discontinuation or refraining from watching 3D contents
yy Do not watch 3D contents when you feel fatigue from lack of sleep, overwork or drinking.
yy When these symptoms are experienced, stop using/watching 3D contents and get enough rest until the
symptom subsides.
-- Consult your doctor when the symptoms persist. Symptoms may include headache, eyeball pain,
dizziness, nausea, palpitation, blurriness, discomfort, double image, visual inconvenience or fatigue.
SAFETY INSTRUCTIONS
9
Viewing Environment
yy Viewing Distance
- Maintain a distance of at least twice the screen diagonal length when watching 3D contents. If you
feel discomfort in viewing 3D contents, move further away from the TV.
Viewing Age
yy Infants/Children
-- Usage/ Viewing 3D contents for children under the age of 5 are prohibited.
-- Children under the age of 10 may overreact and become overly excited because their vision is in
development (for example: trying to touch the screen or trying to jump into it. Special monitoring
and extra attention is required for children watching 3D contents.
-- Children have greater binocular disparity of 3D presentations than adults because the distance between the eyes is shorter than that of adults. Therefore they will perceive more stereoscopic depth
compared to adults for the same 3D image.
yy Teenagers
-- Teenagers under the age of 19 may react with sensitivity due to stimulation from light in 3D contents. Advise them to refrain from watching 3D contens for a long time when they are tired.
yy Elderly
-- The elderly may perceive less 3D effect compared to the young. Do not sit closer to the TV than the
recommended distance.
Cautions when using the 3D glasses
yy Make sure to use LG 3D glasses. Otherwise, you may not be able to view 3D videos properly.
yy Do not use 3D glasses instead of your normal glasses, sunglasses or protective goggles.
yy Using modified 3D glasses may cause eye strain or image distortion.
yy Do not keep your 3D glasses in extremely high or low temperatures. It will cause deformation.
yy The 3D glasses are fragile and are easily scratched. Always use a soft, clean piece of cloth when wiping
the lenses. Do not scratch the lenses of the 3D glasses with sharp objects or clean/wipe them with
chemicals.
ENGLISH
ENG
CAUTION
10
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING
ENG
ENGLISH
NOTE
yyImage shown may differ from your TV.
yyYour TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
yyThe available menus and options may differ from the input source or product model that you are using.
yyNew features may be added to this TV in the future.
yyThe TV can be placed in standby mode in order to reduce the power consumption. And the TV should be turned off if it
will not be watched for some time, as this will reduce energy consumption.
yyThe energy consumed during use can be significantly reduced if the level of brightness of the picture is reduced, and
this will reduce the overall running cost.
INSTALLATION PROCEDURE
1 Open the package and make sure all the accessories are included.
2 Attach the stand to the TV set. (Depending on model)
3 Connect an external device to the TV set.
4 Make sure the network connection is available.
You can use the TV network functions only when the network connection is made.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local dealer where you
purchased your product.
The illustrations in this manual may differ from the actual product and item.
CAUTION
yyDo not use any unapproved items to ensure the safety and product life span.
yyAny damages or injuries by using unapproved items are not covered by the manufacturer’s warranty.
yySome models have a thin film attached on to the screen and this must not be removed.
NOTE
yyThe items supplied with your product may vary depending on the model.
yyProduct specifications or contents of this manual may be changed without prior notice due to upgrade of product functions.
yyFor an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick and 18 mm width.
Use an extension cable that supports USB 2.0 if the USB cable or USB memory stick does not fit into your TV’s USB
port.
B
B
A
A
A
B
10 mm
18 mm
ASSEMBLING AND PREPARING
11
ENGLISH
ENG
SMART
BACK
/Q.MENU
or
Owner’s manual
Remote control,
batteries (AAA)
(Depending on model)
(See p.27, 28)
Magic remote control,
batteries (AA)
(See p.29)
Isolator
(Depending on model)
(See p.12)
AN-VC5**
Video call camera
Component gender
cable
(See p.23)
Composite gender cable
(See p.23, 24)
Cinema 3D glasses
The number of 3D glasses
may differ depending on the
model or country.
Cable Management
(See p.19)
Tag On
Cable Band
(See p.19)
Tag on
AV cover
(See p.17)
Screw (fixing for Cable
Management)
1 EA, M4 x L20
(See p.18, 19)
Fall prevention band
(Depending on model)
(See p.18)
Cleaning Cloth
12
ASSEMBLING AND PREPARING
ENG
ENGLISH
CAUTION
yyIf there is a Isolator, follow as shown.
» Use this to install TV in a place where there is a voltage difference between TV set and GND of antenna signal.
If there is a voltage difference between TV set and GND of antenna signal, the antenna contact might be heated
and excessive heat might cause an accident.
» You can improve the safety when watching TV by efficiently removing power voltage from TV antenna. It is
recommended to mount the isolator to the wall. If it cannot be mounted to the wall, mount it on the TV. Avoid
disconnecting the antenna Isolator after installation.
» Before starting, be sure that the TV antenna is connected.
Connect to TV.
Wall
ANTENNA/
CABLE IN
Cable / Antenna
or
Isolator
Connect to Set-Top box.
Connect one end of the isolator to cable/antenna jack and the other to TV set or set-top box.
“Equipment connected to the protective earthing of the building installation through the mains connection or
through other equipment with a connection to protective earthing - and to a cable distribution system using coaxial
cable, may in some circumstances create a fire hazard. Connection to a cable distribution system has therefore to
be provided through a device providing electrical isolation below a certain frequency range (galvanic isolator, see
EN 60728-11)”
When applying the RF Isolator, a slight loss of signal sensitivity can occur.
ASSEMBLING AND PREPARING
Separate purchase items can be changed or modified for quality improvement without any notification.
Contact your dealer to buy these items.
These devices only work with certain models.
BACK
SMART
/Q.MENU
P
AN-MR400
Magic remote control
AG-F***
Cinema 3D glasses
AG-F***DP
Dual play glasses
LG Audio device
Tag On
Tag On
AN-VC5**
Video call camera
The model name or design may be changed depending on the upgrade of product functions, manufacturer’s
circumstances or policies.
ENGLISH
ENG
Separate purchase
13
14
ASSEMBLING AND PREPARING
ENG
ENGLISH
Parts and buttons
EA98**
Screen
LG Logo Light
Clear Speakers
Speakers
Smart Touch Button
Smart Touch Button
Remote control sensors
Description
Turns the power on or off.
ASSEMBLING AND PREPARING
15
1
To Turn the TV On
-
2
Gently press the smart touch button just below the LG logo light at the bottom of the TV.
To Turn the TV Off
-
If the touch menu is not displayed on the screen, press the smart touch button for about two seconds.
-
If you press the smart touch button for about two seconds when the touch menus are displayed on the screen,
the touch menus will disappear.
LG Logo Light
Smart Touch
CAUTION
yyOnly press the smart touch button gently with your finger.
yyIf you touch any other part except the smart touch button, the TV may not respond.
yyDo not press the smart touch button with two or more fingers. This may cause the product to malfunction. It is
recommended that you only press the button with one finger.
3
To Use the Smart Touch Button
Pꕌ
ꕍ
Programme
Tap
Slide
Tap
Long Tap
1. Press: Selects the menu you want.
2. Press and hold: Returns to the previous step.
If no previous step is available, press and hold turns off the TV.
3. Slide Left/Right: Moves between Programme, Input, Settings, Power Off and Volume menus.
If you want to change the programme or volume setting more quickly, slide your finger left or right to go the programme or Volume menu, and press and hold the menu for about 2 seconds.
ENGLISH
ENG
Using the Smart Touch Button
16
ASSEMBLING AND PREPARING
ENG
ENGLISH
Lifting and moving the TV
Please note the following advice to prevent the TV from
being scratched or damaged and for safe transportation
regardless of its type and size.
yyWhen transporting a large TV, there should be at
least 2 people.
yyWhen transporting the TV by hand, hold the TV as
shown in the following illustration.
CAUTION
yyAvoid touching the screen at all times, as this may
result in damage to the screen.
yyIt is recommended to move the TV in the box or
packing material that the TV originally came in.
yyBefore moving or lifting the TV, disconnect the power
cord and all cables.
yyWhen holding the TV, the screen should face away
from you to avoid damage.
yyWhen transporting the TV, do not expose the TV to
jolts or excessive vibration.
yyWhen transporting the TV, keep the TV upright,
never turn the TV on its side or tilt towards the left or
right.
yyDo not apply excessive pressure to cause flexing /
bending of frame chassis as it may damage screen.
yyBe sure to keep your TV upright instead of laying or
tilting it while moving the TV.
ASSEMBLING AND PREPARING
ENGLISH
ENG
Setting up the TV
Image shown may differ from your TV.
Assembling the AV cover
55EA98**
Please assemble the AV cover as shown in the figure.
2 Connect the power cord to a wall outlet.
CAUTION
AV cover
1 Lift and tilt the TV into its upright position on a table.
-Leave a 10 cm (minimum) space from the wall for
proper ventilation.
10 cm
10 cm
yyDo not place the TV near or on sources of heat, as
this may result in fire or other damage.
WARNING
Mounting on a table
10 cm
10 cm
17
yy If a television is not positioned in a sufficiently
stable location, it can be potentially hazardous
due to falling. Many injuries, particularly to
children, can be avoided by taking simple
precautions such as:
»» Using cabinets or stands recommended by
the manufacturer of the television.
»» Only using furniture that can safely support
the television.
»» Ensuring the television is not overhanging
the edge of the supporting furniture.
»» Not placing the television on tall furniture (for
example, cupboards or bookcases) without
anchoring both the furniture and the television to a suitable support.
»» Not standing the televisions on cloth or other
materials placed between the television and
supporting furniture.
»» Educating children about the dangers of
climbing on furniture to reach the television
or its controls.
18
ASSEMBLING AND PREPARING
ENG
ENGLISH
Securing the TV to a table
2 To secure the TV to a table, insert and tighten
a screw on the rear of the stand.
(Depending on model)
Fix the TV to a table to prevent from tilting forward, damage, and potential injury.
1 Install fall prevention band and cable management
accessories.
Cable Management
Fall prevention band
Fall prevention band
fixing screw
(*Not Provided)
WARNING
yy To prevent TV from falling over, the TV should be
securely attached to the floor/wall per installation
instructions. Tipping, shaking, or rocking the TV
may cause injury.
1 EA
M4 x L20
Fall prevention band
ASSEMBLING AND PREPARING / VIDEO CALL CAMERA
Fix the Cable Management with screw and
arrange the cables.
Product Handling
yyDo not let the camera get wet. Liquid getting into the
camera could cause a short circuit.
yyWipe the camera gently with a dry cloth to remove any
dust or dirt. If the product is very dirty, spray a mild
detergent on the cloth first.
yyDo not clean with thinner, alcohol, benzene or any
other volatile agent.
These may damage the product’s surface or affect its
operation.
yyDo not disassemble, repair or alter the product.
Incorrect disassembly may cause a fire, electric shock,
or injury.
yyDo not shake the camera.
yyDo not pull on the cable.
Cable Management
1 EA
M4 x L20
2
3
Wrap the arranged cables with the
Cable Band.
Pull the zip down.
Installation Instructions
yyMake sure you have enough space for connections
when installing the product.
yyDo not install in a dusty, dirty or moist area.
yyDo not install in direct sunlight or near a heat source.
yyMagnetic objects, such as speakers, may interfere with
the camera’s operation.
yyInstall the product in a place with moderate
temperature and humidity. The recommended
temperature range is 0 °C (32 °F) to 40 °C (104 °F).
yyStrong electromagnetic waves from other devices
could interfere with the camera’s operation.
yyRemove all the protective plastic bags (Vinyl) before
use.
The product and company names contained in this
manual may or may not be registered trademarks
or copyrights, and are only used for identification or
explanatory purposes. All trademarks reserved.
Cable Band
CAUTION
yyDo not move the TV by holding the cable management and cable band, as the cable holders may
break, and injuries and damage to the TV may occur.
ENGLISH
ENG
Video Call Camera
Tidying cables
1
19
20
VIDEO CALL CAMERA
ENG
ENGLISH
Overview
Attaching the video call camera
1
Microphones
Lens
Microphones
Unfold the stand and put it on the top center of
the TV set.
Video Call Camera
Stand
Activity Indicator
2
TV
Bend the stand of the video call camera. Attach
the stand of the video call camera to the back
of the display with a Velcro tape.
USB Cable
Stand-Arm
Video Call Camera
Stand-Cable
holder
Stand-Bottom
Velcro
TV
VIDEO CALL CAMERA / MAKING CONNECTIONS
Insert the video call camera’s cable into the
cable holder. Please open the USB Camera
Cover for video call camera’s cable connection.
The camera shall be connected to the CAM
terminal as shown in the figure.
MAKING CONNECTIONS
Connect various external devices to the TV and switch input modes to select an external device. For more information on external device’s connection, refer to the manual
provided with each device.
Available external devices are: HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC,
gaming devices, and other external devices.
NOTE
Stand-Cable holder
USB Camera cover
NOTE
y For the best quality video and audio outputs,
install the camera on the top-center of your TV.
y Set up with the television switched off.
y When using external speakers, allow sufficient
space between the microphones and the
speakers.
y Make sure to connect the video call camera cable
to the CAM port with the USB trident logo on
the cable facing the front.
y Content can be changed or deleted depending on
Content Provider.
y Please visit the content providers web site for
specific information on their services.
y The software update screen will automatically
appear when an update is available.
y The external device connection may differ from
the model.
y Connect external devices to the TV regardless of
the order of the TV port.
y If you record a TV program on a DVD recorder or
VCR, make sure to connect the TV signal input
cable to the TV through a DVD recorder or VCR.
For more information of recording, refer to the
manual provided with the connected device.
y Refer to the external equipment’s manual for
operating instructions.
y If you connect a gaming device to the TV, use the
cable supplied with the gaming device.
y In PC mode, there may be noise associated
with the resolution, vertical pattern, contrast or
brightness. If noise is present, change the PC
output to another resolution, change the refresh
rate to another rate or adjust the brightness and
contrast on the PICTURE menu until the picture
is clear.
y In PC mode, some resolution settings may not
work properly depending on the graphics card.
ENGLISH
ENG
3
21
22
MAKING CONNECTIONS
ENG
ENGLISH
Antenna connection
Connect the TV to a wall antenna socket with an RF cable
(75 Ω).
HDMI connection
Transmits the digital video and audio signals from an
external device to the TV. Connect the external device
and the TV with the HDMI cable as shown.
Choose any HDMI input port to connect. It does not
matter which port you use.
IN
ANTENNA / CABLE
ANTENNA/
CABLE
DVD / Bly-Ray / HD Cable
Box / HD STB / PC
NOTE
yyUse a signal splitter to use more than 2 TVs.
yyIf the image quality is poor, install a signal amplifier
properly to improve the image quality.
yyIf the image quality is poor with an antenna connected, try to realign the antenna in ANTENNA/
the correct
direction.
CABLE IN
yyAn antenna cable and converter are not provided.
yySupported DTV Audio:
MPEG, Dolby Digital, Dolby Digital Plus,
HE-AAC
(*Not Provided)
HDMI
NOTE
yyIt is recommended to use the TV with the HDMI
connection for the best image quality.
yyUse the latest High Speed HDMI™ Cable with
CEC (Customer Electronics Control) function.
yyHigh Speed HDMI™ Cables are tested to carry
an HD signal up to 1080p and higher.
yySupported HDMI Audio format :
Dolby Digital, DTS, PCM (Up to
192 KHz, 32KHz/44.1KHz/48KHz
/88KHz/96KHz/176KHz/192KHz)
ARC (Audio Return Channel)
yyAn external audio device that supports
SIMPLINK and ARC must be connected using
HDMI/DVI IN 1 (ARC) port.
yyWhen connected with a high-speed HDMI cable,
the external audio device that supports ARC
outputs optical SPDIF without additional optical
audio cable and supports the SIMPLINK function.
MAKING CONNECTIONS
Component connection
Transmits the digital video signal from an external device
to the TV. Connect the external device and the TV with
the DVI-HDMI cable as shown. To transmit an audio
signal, connect an audio cable.
Choose any HDMI input port to connect. It does not
matter which port you use.
Transmits analogue video and audio signals from an
external device to the TV. Connect the external device
and the TV with a component gender cable as shown.
IN
AV
VIDEO
COMPONENT
AUDIO
PR
PB
Y
AV
AV
YELLOW
YELLOW
(Use the composite
video cable
provided.)
BLUE
RED
BLUE
RED
BLUE
GREEN GREEN
RED
RED
WHITE
RED
(*Not Provided)
RED
WHITE
YELLOW
(*Not Provided)
GREEN
(Use the
component video
cable provided.)
(*Not Provided)
AUDIO OUT
DVI OUT
R
AUDIO
DVD / Blu-Ray / HD Cable Box / PC
GREEN
WHITE
L
VIDEO
DVD / Blu-Ray / HD Cable Box
NOTE
yyDepending on the graphics card, DOS mode may
not work if a HDMI to DVI Cable is in use.
yyWhen using the HDMI / DVI cable, Single link is
only supported.
NOTE
yyIf cables are not installed correctly, it could cause
this image to display in black and white or with
distorted colours.
ENGLISH
ENG
DVI to HDMI connection
23
24
MAKING CONNECTIONS
ENG
ENGLISH
Composite connection
Audio connection
Transmits analogue video and audio signals from an
external device to the TV. Connect the external device
and the TV with a composite gender cable as shown.
You may use an external audio system instead of the
built-in speaker.
Digital optical audio connection
Transmits a digital audio signal from the TV to an external
device. Connect the external device and the TV with the
optical audio cable as shown.
AV
VIDEO
IN
AUDIO
COMPONENT
COMPONENT
PR
PB
PB
Y
Y
OUT
OPTICAL
DIGITAL
AUDIO
AV
YELLOW
(Use the composite video
cable provided.)
RED
WHITE
RED
WHITE
YELLOW YELLOW
(*Not Provided)
(*Not Provided)
RED
WHITE
YELLOW
Digital Audio System
VIDEO
VCR / DVD / Blu-Ray /
HD Cable Box
OPTICAL AUDIO IN
L (MONO) AUDIO R
CAUTION
yyDo not look into the optical output port. Looking at
the laser beam may damage your vision.
yyAudio with ACP (Audio Copy Protection) function
may block digital audio output.
MAKING CONNECTIONS
Transmits the headphone signal from the TV to an
external device. Connect the external device and the
TV with the headphone as shown.
Connect a USB storage device such as a USB flash
memory, external hard drive or a USB
memory card reader to the TV and access the Smart
Share menu to use various multimedia files.
3
USB IN
USB connection
USB IN
OUT
2
Ext.Speaker /
H/P
HDD IN
1(USB 3.0 IN)
(*Not Provided)
HDD
(*Not Provided)
HUB
(*Not Provided)
USB
NOTE
(*Not Provided)
yyAUDIO menu items are disabled when connecting a headphone.
yyWhen changing AV MODE with a headphone
connected, the change is applied to video but not
to audio.
yyOptical Digital Audio Out is not available when
connecting a headphone.
yyHeadphone impedance: 16 Ω
yyMax audio output of headphone: 0.624mW to
1.04 mW
yyHeadphone jack size: 0.35 cm
NOTE
HDD IN
USB IN 1
2
3
Apps
yySome USB Hubs may not work. If a USB device
connected using a USB Hub is not detected,
connect it to the USB IN port on the TV directly.
yyConnect the external power source if your USB is
needed.
HDD
(*Not Provided)
ENGLISH
ENG
Headphone connection
25
26
MAKING CONNECTIONS
2
3
/ DVI IN
4(MHL)
Mobile High-definition Link (MHL) is an interface for
transmitting digital audiovisual signals from mobile
phones to television sets.
1 (ARC)
ENG
ENGLISH
MHL connection
MHL passive cable
(*Not Provided)
Mobile phone
NOTE
yyConnect the mobile phone to the HDMI/DVI IN
4(MHL) port to view the phone screen on the TV.
yyThe MHL passive cable is needed to connect the
TV and a mobile phone.
yyThis only works for the MHL-enabled phone.
yySome applications can be operated by the remote
control.
yyFor some mobile phones supporting MHL, you
can control with the magic remote control.
yyRemove the MHL passive cable from the TV
when:
» the MHL function is disabled
» your mobile device is fully charged in standby
mode
REMOTE CONTROL
27
or
CAUTION
yyDo not mix old and new batteries, as this may damage the remote control.
yyIn Analogue TV and some countries, some remote control buttons may not work
Make sure to point the remote control toward the remote control sensor on the TV.
(Depending on model)
RATIO
POWER Turns the TV on or off.
User Guide Sees User Guide.
RATIO Resizes an image.
INPUT Changes the input source.
TV/RAD Selects Radio, TV and DTV programme.
INPUT
TV /
RAD
1
2
3
4
5
6
7
8
9
LIST
0
Q.VIEW
Number buttons Enters numbers.
LIST Accesses the saved programme list.
Q.VIEW Returns to the previously viewed programme.
- Adjusts the volume level.
+
FAV Accesses your favourite programme list.
Uses for viewing 3D video.
MUTE Mutes all sounds.
ꕌPꕍ Scrolls through the saved programmes or channels.
ꕌPAGEꕍ Moves to the previous or next screen.
INFO
FAV
P
MUTE
INFO
SMART MY APPS
Colour buttons These access special functions in some menus.
: Green,
: Yellow,
: Blue)
( : Red,
OK
BACK
GUIDE
EXIT
SUBTITLE
TEXT
T.OPT
Q.MENU
LIVE TV
REC
SETTINGS
AV MODE
P
A
G
E
Views the information of the current programme and screen.
SMART Accesses the HOME menu.
MY APPS Shows the list of Apps.
UP
DOWN
LEFT
RIGHT ) Scrolls
Navigation Buttons (
through menus or options.
OK
Selects menus or options and confirms your input.
BACK Returns to the previous level.
GUIDE Shows programme guide.
EXIT Clears on-screen displays and return to TV viewing.
TELETEXT buttons(TEXT, T.OPT) These buttons are used for teletext.
SUBTITLE Recalls your preferred subtitle in digital mode.
Q.MENU Accesses the Quick menus.
LIVE TV Return to the LIVE TV.
Control buttons (
) Controls the Premium contents,
Time Machine Ⅱ or Smart Share menus or the SIMPLINK compatible
devices (USB or SIMPLINK or Time Machine Ⅱ).
REC
Uses to adjust Time Machine menu.
SETTINGS Accesses the main menus.
AV MODE Selects an AV mode.
Accesses the AV devices connected with the HDMI cable
through HDMI-CEC.
Opens the SIMPLINK menu.
ENGLISH
ENG
REMOTE CONTROL
The descriptions in this manual are based on the buttons on the remote control.
Please read this manual carefully and use the TV correctly. To replace batteries,
and
ends
open the battery cover, replace batteries (1.5 V AAA) matching the
to the label inside the compartment, and close the battery cover. To remove the batteries, perform the installation actions in reverse.
28
REMOTE CONTROL
RATIO
INPUT
TV/
RAD
TV/
RAD
POWER Turns the TV on or off.
SUBTITLE
Recalls
preferred subtitle in digital mode.
.,;@
abc your def
Q. MENU Accesses the quick menus.
GUIDE Shows programme guide.
ghi Resizes
jkl an image.
mno
RATIO
INPUT Changes the input source.
TV/RAD Selects Radio, TV and DTV programme.
GUIDE
1
2
3
4
5
6
7
8
pqrs
tuv
9
wxyz
Number buttons Enters numbers.
LIST Accesses the saved programme list.
Q.VIEW
LIST
Q.VIEW
Returns to the
previously viewed programme.
0
[
ENG
ENGLISH
(Depending on model)
- Adjusts the volume level.
+
FAV
FAV Accesses
your favourite programme list.
P
Uses for viewing 3D video.
A
P GE
MUTE Mutes all sounds.
ꕌPꕍ Scrolls through the saved programmes or channels.
MUTE to the previous or next screen.
ꕌPAGEꕍ Moves
FAV
MUTE
SMART
MY APPS
LIVE TV
REC
TELETEXT BUTTONS (TEXT, T.OPT) These buttons are used for teletext.
INFO
SETTINGS Views the information of the current programme and screen.
MYthe
APPS
HOME menu.
SMART Accesses
MY APPS Shows the list of Apps.
Navigation buttons (up/down/left/right) Scrolls through menus
or options.
SLEEP
OK
SelectsOK
menus or options and confirms your input.
BACK Returns to the previous level.
EXIT Clears on-screen displays and return to TV viewing.
SETTINGS Accesses the main menus.
Uses to adjust Time Machine menu.
REC
LIVE TV Return to the
EXITLIVE TV.
Control buttons (
) Controls the Premium contents,
Time Machine Ⅱ or Smart Share menus or the SIMPLINK compatible
devices (USB or SIMPLINK or Time Machine Ⅱ).
Colour buttons TheseSUBTITLE
access special functions in some menus.
(
: Red,
: Green,
: Yellow,
: Blue)
LIVE TV
REC
INFO
MAGIC REMOTE CONTROL FUNCTIONS
29
MAGIC REMOTE CONTROL FUNCTIONS
ENGLISH
ENG
When the message "Magic remote control battery is low. Change the battery." is
displayed, replace the battery.
and
To replace batteries, open the battery cover, replace batteries (1.5 V AA) matching
ends to the label inside the compartment, and close the battery cover. Be sure to point
the magic remote control toward the remote control sensor on the TV.
To remove the batteries, perform the installation actions in reverse.
2
1
CAUTION
yyDo not mix old and new batteries, as this may damage the remote control.
yyIn Analogue TV and some countries, some remote control buttons may not work
Pointer (RF transmitter)
POWER
Turns the TV on or off.
BACK
Returns to the previous level.
SMART
BACK
LIGHTING ON/OFF
Turns the light on and off.
If you set it to ON, the light automatically turns off in 5 seconds
Voice recognition
(Depending on model)
Wheel(OK)
Selects menus or options and
confirms your input.
Scrolls through the saved programmes.
If you press the navigation button
while moving the pointer on the
screen, the pointer disappears,
and the Magic Remote Control
works as a regular remote control.
To display the pointer again, shake
the Magic Remote Control from
side to side.
SMART
Accesses the HOME menu.
Navigation buttons
( UP DOWN
RIGHT )
/Q.MENU
Adjusts the volume level.
Used for viewing 3D video.
LEFT
Scrolls through menus or options.
ScrollsPthrough the saved programmes or channels.
/Q.MENU
Accesses the quick menus.
Accesses the Screen Remote including number button and colour
button.
MUTE
Mutes all sounds.
Voice recognition (Depending on model)
Network connection is required to use the voice recognition function.
The recognition rate may vary depending on the user’s characteristics (voice, pronunciation, intonation and speed)
and the environment (noise and TV volume).
1.
2.
Press the Voice recognition button.
Speak when the voice display window appears on the left of the TV screen.
• The voice recognition may fail when you speak too fast or too slow.
• Use the Magic remote control no further than 10 cm from your face.
30
MAGIC REMOTE CONTROL FUNCTIONS
ENG
ENGLISH
Registering Magic Remote Control
It is necessary to ‘pair’ (register) the magic remote control to your TV before it will work.
BACK
HOME
How
to register
the Magic Remote Control
P
MY APPS
1 To register automatically,
turn the TV on and press the
Wheel(OK) button. When
registration is completed, the
completion message appears
on the screen.
2 If registration fails, turn the TV
off and back on, then press
the Wheel(OK) button to
complete registration.
How to re-register the Magic Remote Control
BACK
SMART
1 Press and hold the BACK
and SMART buttons
together for 5 seconds to
reset, then register it by
following “How to register
the Magic Remote Control”
above.
2 To re-register the Magic Re
mote Control, press and hold
the BACK button for 5
seconds toward the TV. When
registration is completed, the
completion message appears
on the screen.
How to use Magic Remote Control
1 If the pointer disappears, move
the remote control slightly
to left or right. Then, it will
automatically appear on the
screen.
»»If the pointer has not been
used for a certain period of time, it
will disappear.
2 You can move the pointer by
aiming the Pointer Receiver of
the remote control at your TV
then move it left, right, up or
down.
»»If the pointer does not work
properly, leave the remote control
for 10 seconds then use it again.
1
If you press Wheel(OK) on the Magic Remote
Control, the following screen appears.
Shows information about the current programme
and screen.
2
You can select My Apps Menu.
Precautions to Take when Using
the Magic Remote Control
yyUse the Magic Remote Control within the maximum communication distance (10 m). Using the
Magic Remote Control beyond this distance, or
with an object obstructing it, may cause a communication failure.
yyA communication failure may occur due to nearby
devices. Electrical devices such as a microwave
oven or wireless LAN product may cause interference, as these use the same bandwidth (2.4 GHz)
as the Magic Remote Control.
yyThe Magic Remote Control may be damaged
or may malfunction if it is dropped or receives a
heavy impact.
yyTake care not to bump into nearby furniture or other people when using the Magic Remote Control.
yyManufacturer and installer cannot provide service
related to human safety as the applicable wireless
device has possibility of electric wave interference.
yyIt is recommended that an Access Point (AP) be
located more than 1 m away from the TV. If the
AP is installed closer than 1 m, the Magic Remote
Control may not perform as expected due to frequency interference.
31
USING THE USER GUIDE
1
OPTION > To set language
SMART
 Settings  OPTION  Language
Selects Menu Language and Audio Language displayed on the screen.
User Guide allows you to more easily access the detailed TV information.
Menu Language Selects a language for the display text.
[In Digital Mode Only]
Audio Language When watching a digital broadcast containing several audio
languages, you can select the language you want.
[In Digital mode Only]
Use the Subtitle function when two or more subtitle
Subtitle
languages are broadcast.
Language
✎ If subtitle data in a selected language is not broadcast,
the default language subtitle will be displayed.
1 Press the SMART button to access the Smart
Home menu.
2 Select User Guide and press Wheel(OK).
1
2
Settings
Internet
TV Guide
DVR
Smart Sh..
Universal ...
Pr. List
User Guide
Recent List

User Guide
NOTE
yy You can also access the User Guide by pressing
(User Guide) in the remote control.
(Depending on model)
User Guide
3
1
To use input device
To set time options
PROGRAMME Setting
PICTURE, SOUND Setting
OPTION
To set language
To set country
LG SMART Function
To set Magic remote control
Advanced Function
Information
To set TV lock options
2
To set other options
Online User Guide
Index
4
5
1 Shows the current watching programme or input
source screen.
2 Allows to select the category you want.
3 Allows to select the item you want.
You can use ꕌ/ꕍto move between pages.
4 Allows to browse the description of the function you
want from the index.
5 Provides the detailed information on the functions
of LG Smart TV when the Internet is connected.
(It may not be available depending on the country/
language.)
Try Now
2
Close
index
Input List
ENGLISH
ENG
Using the User guide
Online User Guide
Shows the description of the selected menu.
You can use ꕌ/ꕍto move between pages.
Moves to the selected menu directly from the User
Guide.
32
MAINTENANCE
ENG
ENGLISH
MAINTENANCE
Cleaning Your TV
Clean your TV regularly to keep the best performance and to extend the product lifespan.
CAUTION
yyMake sure to turn the power off and disconnect the power cord and all other cables first.
yyWhen the TV is left unattended and unused for a long time, disconnect the power cord from the wall outlet to
prevent possible damage from lightning or power surges.
Screen, frame, cabinet and stand
To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.
To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild
detergent. Then wipe immediately with a dry cloth.
CAUTION
yyAvoid touching the screen at all times, as this may result in damage to the screen.
yyDo not push, rub, or hit the surface with your fingernail or a sharp object, as this may result in
scratches on the screen and image distortions.
yyDo not use any chemicals as this may damage the product.
yyDo not spray liquid onto the surface. If water enters the TV, it may result in fire,
electric shock, or malfunction.
yyWhen cleaning your TV, do not spray water directly on the left and right speakers at the bottom of the TV.
yyDo not let any water enter your TV and keep it dry.
» Otherwise, this may cause damage to the product, such as corrosion.
Power cord
Remove the accumulated dust or dirt on the power cord regularly.
TROUBLESHOOTING
33
Problem
Solution
yy
Check the remote control sensor on the product and try again.
Cannot control the TV
with the remote control. yy
Check if there is any obstacle between the product and the remote control.
yy
Check if the batteries are still working and properly installed ( to , to
No image display and
no sound is produced.
yy
Check if the product is turned on.
yy
Check if the power cord is connected to a wall outlet.
yy
Check if there is a problem in the wall outlet by connecting other products.
The TV turns off
suddenly.
yy
Check the power control settings. The power supply may be interrupted.
yy
Check if the Auto sleep feature is activated in the Time settings.
yy
If there is no signal while the TV is on, the TV will turn off automatically after
15 minutes of inactivity.
When connecting to
the PC (HDMI/DVI),
‘No signal’ or ‘Invalid
Format’ is displayed.
yy
Turn the TV off/on using the remote control.
yy
Reconnect the HDMI cable.
yy
Restart the PC with the TV on.
If the Notification Window
is not displayed when a
call is received
yyCheck that your status is not set as “Do not disturb”.
yyWhen using certain TV functions, incoming calls can’t be received
(e.g. during a software update, etc.).
yyCheck ‘Privacy Settings’ is “Allow calls from people in my contact list only”.
If there’s echo (e.g. when
you hear your own voice
played back through the
speakers)
yyChange the home theater audio setting to stereo rather than surround.
yyReduce the speaker volume.
yyToo much echo in the room can decrease audio quality.
yyTest microphone using the ‘Echo / Sound Test Service’.
If you’re not able to receive yyInternet or network congestion can degrade video quality.
any video or if it is of low
yyUsing wireless can also degrade video quality. We recommend using a wired internet
quality
connection.
yyScreen quality can decrease when using Zoom-In. We recommend you use minimum
zoom during video calls.
yyCheck whether the call quality information is marked as “critical”. If this is the case,
video quality can be degraded.
If the call ends abruptly
yyWhen certain TV functions are activated, the call may be disconnected. (e.g. Sleep
timer, etc.)
yyDo not unplug the Video Call Camera during a call.
ENGLISH
ENG
TROUBLESHOOTING
).
34
ENVIRONMENTAL INFORMATION
ENG
ENGLISH
Environmental Information
(India only)
WEEE
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is attached to a product it means the product
is covered by the e-waste (Management and Handling) Rules, 2011.
2. All electrical and electronic products should be disposed of separately from the
municipal waste stream via designated collection facilities appointed by the government
or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative
consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance, please contact your city office, waste
disposal service or the shop where you purchased the product.
5. This product does not contain any of the hazardous substances as specified in the rule 13 (1) and (2) of
the e-waste (Management and Handling) Rules, 2011.
i;kZoj.kh; tkudkjh
WEEE
vius iqjkus midj.k dk fuiVku
ƒ. tc ;g dkVs x;s ifg;s okys fcu dk fpg+u fdlh mRikn ds lkFk layXu gksrk gS rks bldk vFkZ gS mRikn
¼izca/ku vkSj gFkkyu½ fu;e „Œƒƒ ds varxZr lfEefyr fd;k x;k gSA
„. lHkh bysfDVªdy ,oa vkSj bysDVªkfud mRiknkas dks ljdkj ;k LFkkuh; vf/kdkfj;ksa }kjk fu;qDr uxjikfydk
ls vyx izkf/kd`r dh xbZ laxzg lqfo/kkvksa ds ek/;e ls fuiVk;k tkuk pkfg,A
/kkjk …. lgh rjhds ls vius iqjkus midj.kksa dk fuiVku okrkoj.k vkSj ekuoh; LokLF; dss fy, laHkkfor udkjkRed ifj.kkeksa dks jksdus esa enn djsxkA
†. vius iqjkus midj.kksa ds fuiVku ds lac/k esa vkSj vf/kd folr`r tkudkjh ds fy,] d`i;k vius uxj dk;kZy;]
ls vkius mRikn [kjhnk Fkk] ogka laidZ djsaA
‡. bl mRikn esa
fuiVku lsok ;k tgka ¼izca/ku vkSj gFkkyu½ fu;e] „Œƒƒ ds fu;e ƒ… ¼ƒ½ vkSj ¼„½ esa funsZ’kkuqlkj dksbZ Hkh gkfudkjd inkFkZ “kkfey ugha gSA
SPECIFICATIONS
Product specifications may be changed without prior notice due to upgrade of product functions.
Wireless LAN module(TWFM-B006D) specification
Standard
IEEE802.11a/b/g/n
2400 to 2483.5 MHz
Frequency Range
5150 to 5250 MHz
5725 to 5850 MHz (for Non EU)
802.11a: 11 dBm
Output Power
(Max.)
802.11b: 14 dBm
802.11g: 10.5 dBm
802.11n - 2.4GHz: 11 dBm
802.11n - 5GHz: 12.5 dBm
Bluetooth module (BM-LDS401) specification
Standard
Frequency Range
Output Power (Max.)
Bluetooth Version 3.0
2400 ~ 2483.5 MHz
10 dBm or lower
yyBecause band channel used by the country could be different, the user can not change or adjust the operating frequency and this product is set for the regional frequency table.
ENGLISH
ENG
SPECIFICATIONS
35
36
SPECIFICATIONS
ENG
ENGLISH
55EA98**
55EA9800-TA
MODEL
55EA980Y-TA
1227 x 798.5 x 192
Dimensions (W x H x D) (mm)
Weight (kg)
17.2
Power requirement
AC 100-240 V~ 50 / 60 Hz
Operating Temperature
Environment
condition
0 °C to 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
Digital TV
Analogue TV
(Depending on Country)
(Depending on Country)
PAL B/B, PAL B/G, PAL D/K, PAL-I
Television System
DVB-T
SECAM B/G, SECAM D/K
Programme Coverage
Maximum number of
VHF, UHF
NTSC-M
VHF, UHF, CATV
storable programmes
External Antenna Impedance
MODEL
Dimensions (Width x Height x Depth)
DVB-T & Analogue TV : 1,500
75 Ω
AN-VC500
(Video Call Camera)
112 mm x 56 mm x 38 mm
Weight
107.8 g
Lens
Video
Effective pixels
Audio
Focus
More than 100 cm
Field of Vision
61.25° in diagonal
1920 x 1080
Output format
H.264, MJPEG, YUV
Output Image
Full-HD, HD, VGA, QVGA, QQVGA
Microphone
2 microphones
Interface
Environmental conditions
USB
Operating Temperature
0 °C - 40 °C
Operating Humidity
0 % - 80 %
Storage Temperature
Storage Humidity
-20 °C - 70 °C
0 % - 90 %
y The specifications shown above may be altered without prior notice to improve quality.
NOTE
The list of devices that are not supported may be amended without prior notification.
yy
SPECIFICATIONS
Resolution
640x480
720x480
720x576
1280x720
1920x1080
Vertical
Frequency
(kHz)
(Hz)
31.469
59.94
31.5
60
31.469
59.94
31.5
60
31.25
50
37.5
50
44.96
59.94
45
60
33.72
59.94
33.75
60
28.125
50
26.97
23.97
27
24
33.716
29.976
33.75
30.00
56.25
50
67.43
59.94
67.5
60
HDMI/DVI-PC supported mode
Resolution
Horizontal
Frequency
(kHz)
Vertical Frequency (Hz)
640 x 350
31.468
70.09
720 x 400
31.469
70.08
640 x 480
31.469
59.94
800 x 600
37.879
60.31
1024 x 768
48.363
60.00
1152 x 864
54.348
60.053
1360 x 768
47.712
60.015
1280 x 1024
63.981
60.020
1920 x 1080
67.50
60.00
Component ports on the TV
Video output ports on DVD
player
Y
PB
PR
Y
PB
PR
Y
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
Signal
Component
480i/576i
O
480p/576p
O
720p/1080i
O
1080p
O
(50 Hz / 60 Hz only)
ENGLISH
ENG
Component port connecting information
HDMI/DVI-DTV supported mode
Horizontal
Frequency
37
38
SPECIFICATIONS
ENG
ENGLISH
3D supported mode
yyVideo, which is input as below media contents is switched into the 3D screen automatically.
3D supported mode automatically
Input
Signal
640 X 480
480p
576p
720p
HDMI
1080i
1080p
Horizontal
Vertical
Frequency (kHz) Frequency (Hz)
Top & Bottom,
Side by Side(Half), Side by Side(Full)
31.469 / 31.5
62.938 / 63
31.469 / 31.5
59.94 / 60
62.5
Frame Packing, Line Alternative
Top & Bottom,
Side by Side(Half), Side by Side(Full)
Frame Packing, Line Alternative
62.938 / 63
31.25
Playable 3D video format
50
37.50
50
44.96 / 45
59.94 / 60
75
50
89.91 / 90
59.94 / 60
28.125
50
33.72 / 33.75
59.94 / 60
56.25
50
67.432 / 67.5
59.94 / 60
26.97 / 27
23.97 / 24
28.125
25
33.716 / 33.75
29.976 / 30
43.94 / 54
23.97 / 24
56.25
25
67.432 / 67.5
29.976 / 30
56.25
50
67.432 / 67.5
59.94 / 60
USB
1080p
33.75
30
DLNA
1080p
33.75
30
Top & Bottom,
Side by Side(Half), Side by Side(Full)
Frame Packing, Line Alternative
Top & Bottom,
Side by Side(Half), Side by Side(Full)
Frame Packing, Line Alternative
Top & Bottom,
Side by Side(Half), Side by Side(Full)
Frame Packing, Field Alternative
Top & Bottom,
Side by Side(Half), Side by Side(Full)
Frame Packing, Line Alternative
Top & Bottom, Side by Side(Half)
Side by Side(Half), Top & Bottom,
Checker Board, MPO(Photo), JPS(Photo)
SPECIFICATIONS
39
ENGLISH
ENG
3D supported mode manually
Signal
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency (Hz)
HD / SD
-
-
ATV(CVBS)
SD
-
-
Component
HD / SD
-
-
1024x768
48.36
1360x768
47.71
Input
DTV
HDMI-PC
60
1920x1080
67.5
Others
-
-
480p
31.5
60
576p
31.25
50
37.5
50
45
60
28.12
50
33.75
60
720p
1080i
HDMI-DTV
1080p
Under 704x480
USB, DLNA
(Movie)
USB, DLNA
(Photo)
Miracast/Widi
27
24
28.12
25
33.75
30
56.25
50
67.5
60
-
-
Over 704x480
interlaced
-
-
Over 704x480
progressive
-
50 / 60
Over 704x480
progressive
-
Others
Under 320x240
-
-
Over 320x240
-
-
1024x768p
1280x720p
1920x1080p
Others
-
30 / 60
-
30 / 60
-
30 / 60
-
-
Playable 3D video format
2D to 3D, Side by
Side(Half), Top & Bottom
2D to 3D, Side by
Side(Half), Top & Bottom,
Checker Board, Frame Sequential, Row Interleaving,
Column Interleaving
2D to 3D, Side by
Side(Half), Top & Bottom
2D to 3D, Side by
Side(Half), Top & Bottom,
Checker Board, Frame Sequential, Row Interleaving,
Column Interleaving
2D to 3D, Side by
Side(Half), Top & Bottom
2D to 3D, Side by
Side(Half), Top & Bottom,
Checker Board, Row Interleaving, Column Interleaving
2D to 3D, Side by
Side(Half), Top & Bottom,
Checker Board, Frame Sequential, Row Interleaving,
Column Interleaving
2D to 3D
2D to 3D, Side by
Side(Half), Top & Bottom
2D to 3D, Side by
Side(Half), Top & Bottom,
Checker Board, Frame Sequential, Row Interleaving,
Column Interleaving
2D to 3D, Side by
Side(Half), Top & Bottom,
Checker Board, Row Interleaving, Column Interleaving
2D to 3D
2D to 3D, Side by
Side(Half), Top & Bottom
2D to 3D, Side by
Side(Half), Top & Bottom
2D to 3D
40
LICENSES / OPEN SOURCE SOFTWARE NOTICE
ENG
ENGLISH
LICENSES
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
Manufactured under license from Dolby Laboratories. “Dolby” and the doubleD symbol are trademarks of Dolby Laboratories.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the
HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in
the United States and other countries.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a
subsidiary of Rovi Corporation. This is an official DivX Certified® device that
plays DivX video. Visit divx.com for more information and software tools to
convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be
registered in order to play purchased DivX Video-on-Demand (VOD) movies.
To obtain your registration code, locate the DivX VOD section in your device
setup menu. Go to vod.divx.com for more information on how to complete your
registration.
“DivX Certified® to play DivX® video up to HD 1080p, including premium
content.”
“DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under license.”
“Covered by one or more of the following U.S. patents :
7,295,673; 7,460,668; 7,515,710; 7,519,274”
Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380;
6,487,535 & other U.S. and worldwide patents issued & pending. DTS, the
Symbol & DTS and the Symbol together are registered trademarks & DTS
2.0+Digital Out is a trademark of DTS, Inc. Product includes software. © DTS,
Inc. All Rights Reserved.
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product,
please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for
download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such
distribution (such as the cost of media, shipping and handling) upon email request to opensource@lge.com. This offer is
valid for three (3) years from the date on which you purchased the product.
External control device setup
To obtain the external control device setup information, please visit www.lg.com
Record the model number and serial number of
the TV.
Refer to the label on the back cover and quote
this information to your dealer when requiring
any service.
MODEL
SERIAL
(Only DTV)
OWNER’S MANUAL
EXTERNAL CONTROL
DEVICE SETUP
Please read this manual carefully before operating the set and retain it for
future reference.
www.lg.com
2
KEY CODES
ENGLISH
ENG
KEY CODES
• This feature is not available for all models.
Code
(Hexa)
Function
Note
Code
(Hexa)
Function
Note
00
CH +, PR +
R/C Button
45
Q.Menu
R/C Button
01
CH -, PR -
R/C Button
4C
List, - (ATSC Only)
R/C Button
02
Volume +
R/C Button
53
List
R/C Button
03
Volume -
R/C Button
5B
Exit
R/C Button
06
> (Arrow Key / Right Key)
R/C Button
61
Blue
R/C Button
07
< (Arrow Key / Left Key)
R/C Button
63
Yellow
R/C Button
08
Power
R/C Button
71
Green
R/C Button
09
Mute
R/C Button
72
Red
R/C Button
0B
Input
R/C Button
79
Ratio / Aspect Ratio
R/C Button
0E
SLEEP
R/C Button
91
AD (Audio Description)
R/C Button
0F
TV, TV/RAD
R/C Button
7A
User Guide
R/C Button
R/C Button
7C
Smart/ Home
R/C Button
10 - 19 * Number Key 0 - 9
1A
Q.View / Flashback
R/C Button
7E
Simplink
R/C Button
1E
FAV (Favorite Channel)
R/C Button
8E
►► (Forward)
R/C Button
20
Text (Teletext)
R/C Button
8F
◄◄ (Rewind)
R/C Button
21
T. Opt (Teletext Option)
R/C Button
AA
Info
R/C Button
28
Return (BACK)
R/C Button
AB
Program Guide
R/C Button
30
AV (Audio/ Video) Mode
R/C Button
B0
► (Play)
R/C Button
39
Caption/Subtitle
R/C Button
B1
ꕗ (Stop/ Live TV)
R/C Button
40
Λ (Arrow Key/ Cursor Up)
R/C Button
BA
ꕘ (Freeze/Slow Play/Pause)
R/C Button
41
V (Arrow Key/ Cursor Down)
R/C Button
BD
● (REC)
R/C Button
42
My Apps
R/C Button
DC
3D
R/C Button
43
Menu / Settings
R/C Button
9F
App/ *
R/C Button
44
OK / Enter
R/C Button
* Key code 4C (0x4C) is available on ATSC/ISDB models which use major/minor channel.
(For South Korea, Japan, North America, Latin America except Colombia models)
EXTERNAL CONTROL DEVICE SETUP
3
• Image shown may differ from your TV.
Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer
or an A/V control system) to control the product’s functions externally.
Note: There are several ways to connect TV based on model’s support port.
* Please be advised that not all models support these connectivity.
* Cable is not provided.
USB to Serial converter with USB Cable
USB IN
USB Type
(PC)
(TV)
• LGTV supports PL2303 chip-based (Vendor ID : 0x0557, Product
ID :IN0x2008) USB to serial converter
RS-232C
(CONTROL & SERVICE)
which is not made nor provided by LG.
• It can be purchased from computer stores that carry accessories for IT support professionals.
(TV)
(PC)
USB IN
RS-232C With RS232C Cable
(PC)
(TV)
SERVICE ONLY
DE9 (D-Sub 9pin) Type
1
• You need to purchase the RS-232C (DE9, D-Sub
3 9pin female-to-female type) to RS-232C cable required
for the connection between the PC and the TV, which is specified in the manual.
(PC)
2
RS-232C IN
(CONTROL & SERVICE)
(PC)
(TV)
1
3
(PC)
(TV)
(TV)
SERVICE ONLY
• This connection can only be used for the following models:
55/65/LA97**, 84LA98**
1
3
RS-232C IN
(CONTROL & SERVICE)
2
(PC)
2
(TV)
1
3
(PC)
RS-232C IN
2
RS-232C IN
(CONTROL & SERVICE)
RS-232C IN
(CONTROL & SERVICE)
(TV)
ENGLISH
ENG
EXTERNAL CONTROL DEVICE SETUP
USB USB
IN I
(PC)
EXTERNAL CONTROL DEVICE SETUP
(PC)
4
(TV)
(TV)
RS-232C IN
(TV)
(TV)
(PC)
(PC)
* For other models, connect to the USB port.
1
3
(PC)
(PC)
1
3
2
2
SERVICE
ONLY ONLY
SERVICE
ENGLISH
ENG
(CONTROL & SERVICE)
Phone jack Type
RS-232C
• You need to purchase the phone-jack to RS-232 cable required
for theIN connection between the PC and
(CONTROL & SERVICE)
the TV, which is specified in the manual.
(TV)
(TV)
-- This connection can only be used for the following models: 55/47/39LN5450-UA, 55/50/47/42LN5400UA, 42/39/32LN5300-UA, and 37/32LN530B-UA.
1
3
(PC)
(PC)
1
3
RS-232C IN
(CONTROL & SERVICE)
2
RS-232C IN
(TV)
(TV)
(CONTROL & SERVICE)
2
-- This connection can only be used for the following models: 60PN6550-UA, 50/60PN6500-UA,
50/60PN5300-UF, and 42/50PN4500-UA.
Customer Computer
RS-232C configurations
3-Wire Configurations(Not standard)
1
5
PC
RS-232C IN
RXD
2
2
TXD
TXD
3
1
RXD
GND
5
3
GND
(CONTROL & SERVICE)
RS-232C IN
(CONTROL & SERVICE)
6
OR
9
RS-232C
(Serial port)
TV
RXD
3
2
TXD
TXD
2
1
RXD
GND
5
3
GND
D-Sub 9
Phone
Set ID
For Set ID number, see "Real Data Mapping" on p. 6
1. Press SETTINGS to access the main menus.
2. Press the Navigation buttons to scroll to OPTION and press OK.
3. Press the Navigation buttons to scroll to SET ID and press OK.
4. Scroll left or right to select a set ID number and select CLOSE. The adjustment range is 1-99.
5. When you are finished, press EXIT.
EXTERNAL CONTROL DEVICE SETUP
5
• Baud rate : 9600 bps (UART)
• Data length : 8 bits
• Parity : None
ENGLISH
ENG
Communication Parameters
• Stop bit : 1 bit
• Communication code : ASCII code
• Use a crossed (reverse) cable.
Command reference list
(Depending on model)
COMMAND1 COMMAND2
DATA
(Hexadecimal)
01. Power*
k
a
00 to 01
02. Aspect
Ratio
k
c
(See p.7)
03. Screen
Mute
k
d
(See p.7)
k
e
00 to 01
k
f
00 to 64
06. Contrast k
g
00 to 64
07.
Brightness
h
00 to 64
04. Volume
Mute
05. Volume
Control
k
08. Color/
Colour
k
i
00 to 64
09. Tint
k
j
00 to 64
10.
Sharpness
k
k
00 to 32
11. OSD
Select
k
l
00 to 01
12. Remote
Control
Lock Mode
k
m
00 to 01
COMMAND1 COMMAND2
DATA
(Hexadecimal)
k
t
00 to 64
x
u
00 to 64
j
p
(See p.8)
j
q
00 to 05
m
a
(See p.8)
m
b
00 to 01
19. Key
m
c
20. Control
Back Light,
Control Panel
Light
21. Input
select (Main)
22. 3D
(Only 3D
models)
23. Extended
3D (Only 3D
models)
m
g
Key
Codes
00 to 64
x
b
(See p.10)
x
t
(See p.11)
x
v
(See p.11)
13. Balance
14. Color
(Colour)
Temperature
15. ISM
Method (Only
Plasma TV)
16. Energy
Saving
17. Tune
Command
18. Channel
(Programme)
Add/Del(Skip)
* Note: During USB operations such as DivX or EMF, all commands except Power(ka) and Key(mc) are
not executed and treated as NG.
With RS232C cable, TV can communicate "ka command" in power-on or power-off status. but with
USB-to-Serial converter cable, the command works only if TV is on.
6
EXTERNAL CONTROL DEVICE SETUP
ENGLISH
ENG
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1] : First command to control the TV. (j, k, m or x)
[Command 2] : Second command to control the TV.
[Set ID]
:You can adjust the [Set ID] to choose desired monitor ID number in option menu.
Adjustment range in TV is 1 to 99. If [Set ID] value is selected to ‘0’, every connected set
can be controlled.
* [Set ID] is indicated as decimal (1 to 99) on menu and as Hexadecimal (0x00 to 0x63) on
transmission/receiving protocol.
[DATA] : To transmit command data (hexadecimal). Transmit ‘FF’ data to read status of command.
[Cr] : Carriage Return - ASCII code ‘0x0D’
[ ]
: Space – ASCII code ‘0x20’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time,
if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the
data of the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from nonviable functions or communication errors.
Data 00: Illegal Code
Real data mapping (Hexadecimal b Decimal)
* When you enter the [data] in hexadecimal, refer to following conversion table.
* Channel Tune (ma) Command uses two-byte hexadecimal value([data]) to select channel number.
00 : Step 0
01 : Step 1 (Set ID 1)
...
0A : Step 10 (Set ID 10)
...
0F : Step 15 (Set ID 15)
10 : Step 16 (Set ID 16)
...
32 : Step 50 (Set ID 50)
33 : Step 51 (Set ID 51)
...
63 : Step 99 (Set ID 99)
...
C7 : Step 199
C8 : Step 200
...
FE : Step 254
FF : Step 255
...
01 00 : Step 256
...
27 0E : Step 9998
27 0F : Step 9999
...
EXTERNAL CONTROL DEVICE SETUP
7
* Commands may work differently depending on model and signal.
04.Volume Mute (Command: k e)
►► To control Power *On or Off of the set.
►► To control volume mute on/off.
You can also adjust mute using the MUTE button
on remote control.
Transmission[k][a][ ][Set ID][ ][Data][Cr]
Data 00 : Power Off
01 : *Power On
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
►► To Show TV is Power On or *Off
Transmission [k][a][ ][Set ID][ ][FF][Cr]
Transmission [k][e][ ][Set ID][ ][Data][Cr]
Data 00 : Volume mute on (Volume off)
01 : Volume mute off (Volume on)
Ack [e][ ][Set ID][ ][OK/NG][Data][x]
Ack [a][ ][Set ID][ ][OK][Data][x]
* Similarly, if other functions transmit ‘FF’ data
based on this format, Acknowledgement feedback
presents status about each function.
* With RS232C cable, TV can communicate "ka command"
in power-on or power-off status. but with USB-to-Serial
converter cable, the command works only if TV is on.
05.Volume Control (Command: k f)
►► To adjust volume.
You can also adjust volume with the volume
buttons on remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
02. Aspect Ratio (Command: k c)
(Main Picture Size)
►► To adjust the screen format. (Main picture format)
You can also adjust the screen format using the
Aspect Ratio in the Q.MENU. or PICTURE menu.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 01 : Normal screen
(4:3)
02 : Wide screen
(16:9)
04 : Zoom
05 : Zoom 2
(Latin America
except Colombia
Only)
06 : Set by Program/
Original
07 : 14:9
(Europe, Colombia, MidEast, Asia except South
Korea and Japan)
09 : * Just Scan
0B : Full Wide
(Europe, Colombia, MidEast, Asia except South
Korea and Japan)
10 to 1F : C
inema Zoom 1
to 16
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
* Using the PC input, you select either 16:9 or 4:3
screen aspect ratio.
* In DTV/HDMI/Component mode (high-definition),
Just Scan is available.
* Full wide mode may work differently based on model
and is supported for DTV fully, and ATV, AV partially.
03. Screen Mute (Command: k d)
►► To select screen mute on/off.
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data 00 : S
creen mute off (Picture on), Video mute off
01 : Screen mute on (Picture off)
10 : Video mute on
Ack [d][ ][Set ID][ ][OK/NG][Data][x]
* In case of video mute on only, TV will display On
Screen Display(OSD). But, in case of Screen mute
on, TV will not display OSD.
Ack [f][ ][Set ID][ ][OK/NG][Data][x]
06.Contrast (Command: k g)
►► To adjust screen contrast.
You can also adjust contrast in the PICTURE
menu.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
07.Brightness (Command: k h)
►► To adjust screen brightness.
You can also adjust brightness in the PICTURE
menu.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [h][ ][Set ID][ ][OK/NG][Data][x]
08.Color/Colour (Command: k i)
►► To adjust the screen Color(Colour).
You can also adjust colour in the PICTURE menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [i][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
ENG
01.Power (Command: k a)
8
EXTERNAL CONTROL DEVICE SETUP
ENGLISH
ENG
09.Tint (Command: k j)
14.Color(Colour) Temperature (Command: x u)
►► To adjust the screen tint.
You can also adjust tint in the PICTURE menu.
►► To adjust colour temperature. You can also adjust
Color(Colour) Temperature in the PICTURE menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Data Red : 00 to Green : 64
Ack [j][ ][Set ID][ ][OK/NG][Data][x]
Transmission [x][u][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
10.Sharpness (Command: k k)
15.ISM Method (Command: j p) (Only Plasma TV)
►► To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE
menu.
►► To control the ISM method. You can also adjust
ISM Method in OPTION menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 32
Ack [k][ ][Set ID][ ][OK/NG][Data][x]
11.OSD Select (Command: k l)
►► To select OSD (On Screen Display) on/off when
controlling remotely.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00 : OSD off
01 : OSD on
Ack [l][ ][Set ID][ ][OK/NG][Data][x]
12.Remote control lock mode (Command: k m)
►► To lock the front panel controls on the monitor and
remote control.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00 : Lock off
Transmission [j][p][ ][Set ID][ ][Data][Cr]
Data Min : 02: Orbiter
08: Normal
20: Color(Colour) Wash
Ack [p][ ][Set ID][ ][OK/NG][Data][x]
16.Energy Saving (Command: j q)
►► To reduce the power consumption of the TV. You
can also adjust Energy Saving in PICTURE menu.
Transmission [j][q][ ][Set ID][ ][Data][Cr]
Data
00 : Off
01 : Minimum
02 : Medium
03 : Maximum
04 : Auto
05 : Screen off
* (Depending on model)
Ack [q][ ][Set ID][ ][OK/NG][Data][x]
01 : Lock on
Ack [m][ ][Set ID][ ][OK/NG][Data][x]
* If you are not using the remote control, use this
mode.
When main power is off & on (plug-off and plug-in,
after 20 - 30 seconds), external control lock is
released.
* In the standby mode (DC off by off timer or ‘ka’,
‘mc’ command), and if key lock is on, TV will not
turn on by power on key of IR & Local Key.
13.Balance (Command: k t)
►► To adjust balance.
You can also adjust balance in the AUDIO menu.
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [t][ ][Set ID][ ][OK/NG][Data][x]
17.Tune Command (Command: m a)
* This command may work differently depending on
model and signal.
• For Europe, Mid-East, Colombia, Asia except
South Korea and Japan Model
►► Select channel to following physical number.
Transmission [m][a][ ][Set ID][ ][Data 00][ ][Data 01]
[ ][Data 02][Cr]
* Analogue Terrestrial/Cable
[Data 00][Data 01] Channel Data
Data00 : High byte channel data
Data01 : Low byte channel data
- 00 00 ~ 00 C7 (Decimal : 0 ~ 199)
Data 02 : Input Source (Analogue)
- 00 : Terrestrial TV (ATV)
- 80 : Cable TV (CATV)
EXTERNAL CONTROL DEVICE SETUP
[Data 00][Data 01]: Channel Data
Data00 : High Channel data
Data01 : Low Channel data
- 00 00 ~ 27 0F (Decimal: 0 ~ 9999)
Data05: Input Source (Analogue)
- 00 : Terrestrial TV (ATV)
- 01 : Cable TV (CATV)
* Digital Terrestrial/Cable
Data00 : xx (Don't care)
Data02 : Input Source (Digital)
- 10 : Terrestrial TV (DTV)
- 20 : Terrestrial Radio (Radio)
- 40 : Satellite TV (SDTV)
- 50 : Satellite Radio (S-Radio)
- 90 : Cable TV (CADTV)
- a0 : Cable Radio (CA-Radio)
[Data 01][Data 02]: Major Channel Number
Data01 : High byte Channel Data
Data02 : Low byte Channel Data
- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)
[Data 03][Data 04]: Minor Channel Number
Data03 : High byte Channel Data
Data04 : Low byte Channel Data
* Tune Command Examples:
1.Tune to the analogue terrestrial (PAL) Channel 10.
Set ID = All = 00
Data 00 & 01 = Channel Data is 10 = 00 0a
Data 02 = Analogue Terrestrial TV = 00
Result = ma 00 00 0a 00
Data05 : Input Source (Digital)
- 02 : Terrestrial TV (DTV) – Use Physical Channel
Number
- 06 : Cable TV (CADTV) – Use Physical Channel
Number
- 22 : Terrestrial TV (DTV) – Don’t Use Physical
Channel Number
- 26 : Cable TV (CADTV) - Don’t Use Physical
Channel Number
- 46 : Cable TV (CADTV) – Use Major Channel
Number Only (One Part Channel)
Two bytes are available for each major and minor
channel data, but usually the low byte is used alone
(high byte is 0).
2.Tune to the digital terrestrial (DVB-T) Channel 01.
Set ID = All = 00
Data 00 & 01 = Channel Data is 1 = 00 01
Data 02 = Digital Terrestrial TV = 10
Result = ma 00 00 01 10
3.Tune to the satellite (DVB-S) Channel 1000.
Set ID = All = 00
Data 00 & 01 = Channel Data is 1000 = 03 E8
Data 02 = Digital Satellite TV = 40
Result = ma 00 03 E8 40
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01][Data 02][x]
[a][ ][Set ID][ ][NG][Data 00][x]
• For South Korea, North/Latin America except
Colombia Model
►► To tune channel to following physical/major/minor
number.
Transmission [m][a][ ][0][ ][Data00][ ][Data01]
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
Digital channels have a Physical, Major, and Minor
channel number. The Physical number is the actual
digital channel number, the Major is the number that
the channel should be mapped to, and the Minor is
the sub-channel. Since the ATSC tuner automatically
maps the channel from the Major / Minor number,
the Physical number is not required when sending a
command in Digital.
* Analogue Terrestrial/Cable
Data00 : Physical Channel Number
- Terrestrial (ATV) : 02~45 (Decimal: 2 ~ 69)
- Cable (CATV) : 01, 0E~7D (Decimal : 1, 14~125)
[Data 01 ~ 04]: Major/Minor Channel Number
Data01 & 02: xx (Don't care)
Data03 & 04: xx (Don't care)
* Tune Command Examples:
1.Tune to the analogue cable (NTSC) channel 35.
Set ID = All = 00
Data 00 = Channel Data is 35 = 23
Data 01 & 02 = No Major = 00 00
Data 03 & 04 = No Minor = 00 00
Data 05 = Analogue Cable TV = 01
Total = ma 00 23 00 00 00 00 01
2.Tune to the digital terrestrial (ATSC) channel 30-3.
Set ID = All = 00
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 30 = 00 1E
Data 03 & 04 = Minor is 3 = 00 03
Data 05 = Digital Terrestrial TV = 22
Total = ma 00 00 00 1E 00 03 22
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
[Data 02][Data 03][Data 04][Data 05]
[x][a][ ][Set ID][ ][NG][Data 00][x]
• For Japan Model
►► To tune channel to following physical/major/minor
number.
Transmission [m][a][ ][0][ ][Data00][ ][Data01]
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
* Digital Terrestrial/Satellite
Data 00: xx (Don't care)
ENGLISH
ENG
* Digital Terrestrial/Cable/Satellite
9
10 EXTERNAL CONTROL DEVICE SETUP
ENGLISH
ENG
[Data 01][Data 02]: Major Channel Number
Data 01: High byte Channel Data
Data 02: Low byte Channel Data
- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)
[Data 03][Data 04]: Minor/Branch Channel Number
(Don’t care in Satellite)
Data 03: High byte Channel Data
Data 04: Low byte Channel Data
Data 05 : Input Source (Digital/Satellite for Japan)
- 02 : Terrestrial TV (DTV)
- 07 : BS (Broadcasting Satellite)
- 08 : CS1 (Communication Satellite 1)
- 09 : CS2 (Communication Satellite 2)
* Tune Command Examples:
1 Tune to the digital terrestrial (ISDB-T) channel 17-1.
Set ID = All = 00
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 17 = 00 11
Data 03 & 04 = Minor/Branch is 1 = 00 01
Data 05 = Digital Terrestrial TV = 02
Total = ma 00 00 00 11 00 01 02
20.Control Back Light (Command: m g)
• For LCD TV / LED TV
►► To control the back light.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
Control Panel Light (Command: m g)
• For Plasma TV
►► To control the panel light.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
21.Input select (Command: x b)
(Main Picture Input)
►► To select input source for main picture.
2.Tune to the BS (ISDB-BS) channel 30.
Set ID = All = 00
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 30 = 00 1E
Data 03 & 04 = Don’t Care = 00 00
Data 05 = Digital BS TV = 07
Total = ma 00 00 00 1E 00 00 07
Transmission [x][b][ ][Set ID][ ][Data][Cr]
* This feature is varied based on the model.
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
[Data 02][Data 03][Data 04][Data 05]
[x][a][ ][Set ID][ ][NG][Data 00][x]
18.Channel(Programme) Add/Del(Skip)
(Command: m b)
►► To skip current channel(programme) for next time.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 00 : Del(ATSC,ISDB)/Skip(DVB)
01 : Add
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
* Set the saved channel status to del(ATSC, ISDB)/
skip(DVB) or add.
19.Key (Command: m c)
►► To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
DataKey code - See p.2.
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
Data
00 : DTV
01 : CADTV
02 : Satellite DTV
10 : ATV
ISDB-BS (Japan)
03 : ISDB-CS1 (Japan)
04 : ISDB-CS2 (Japan)
11 : CATV
20 : AV or AV1
21 : AV2
40 : Component1
41 : Component2
90 : HDMI1
92 : HDMI3
91 : HDMI2
93 : HDMI4
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
* This function depends on model and signal.
EXTERNAL CONTROL DEVICE SETUP
(Depending on model)
►► To change 3D mode for TV.
Transmission [x][t][ ][Set ID][ ][Data 00][ ][Data 01]
[ ][Data 02][ ][Data 03][Cr]
DataStructure
[Data 00]00 : 3D On
01 : 3D Off
02 : 3D to 2D
03 : 2D to 3D
[Data 01]00 : Top and Bottom
01 : Side by Side
02 : Checker Board
03 : Frame Sequential
04 : Column interleaving
05 : Row interleaving
[Data 02]00 : Right to Left
01 : Left to Right
[Data 03]3D Effect(3D Depth): Min : 00 - Max : 14
(*transmit by Hexadecimal code)
* If [Data 00] is 01 (3D off) or 02 (3D to 2D), [Data
01], [Data 02] and [Data 03] have no meaning.
* If [Data 00] is 03(2D to 3D), [Data 01] have no
meaning.
* If [Data 00] is 00 (3D On) or 03 (2D to 3D), [Data
03] works when 3D Mode (Genre) is manual only
* All 3D pattern options ([Data 01]) may not be
available according to broadcasting/video signal.
[Data 00]
[Data 01]
[Data 02]
[Data 03]
00
O
O
O
01
X
X
X
02
X
X
X
03
X
O
O
X : don’t care
Ack [t][ ][Set ID][ ][OK][Data00][Data01][Data02]
[Data03][x]
[t][ ][Set ID][ ][NG][Data00][x]
23.Extended 3D(Command: x v) (only 3D models)
(Depending on model)
►► To change 3D option for TV.
Transmission [x][v][ ][Set ID][ ][Data 00][ ]
[Data 01][Cr]
[Data 00]3D option
00 : 3D Picture Correction
01 : 3D Depth (3D Mode is Manual Only)
02 : 3D Viewpoint
06 : 3D Color Correction
07 : 3D Sound Zooming
08 : Normal Image View
09 : 3D Mode (Genre)
[Data 01]It has own range for each 3D option
determined by [Data 00].
1) When[Data 00] is 00
00 : Right to Left
01 : Left to Right
2) When[Data 00] is 01, 02
DataMin: 0 - Max: 14 (*transmit by Hexadecimal
code)
Data value range(0 - 20) converts Viewpoint range
(-10 - +10) automatically (Depending on model)
* This option works when 3D Mode (Genre) is manual
only.
3) When[Data 00] is 06, 07
00 : Off
01 : On
4) When [Data 00] is 08
00 : Revert to 3D video from 3D-to-2D
converted 2D video
01 : Change 3D video to 2D video, except
2D-to-3D video
* If conversion condition doesn’t meet, command is
treated as NG.
5) When [Data 00] is 09
00 : Standard
02 : Cinema
04 : Manual
01 : Sport
03 : Extreme
Ack [v][ ][Set ID][ ][OK][Data00][Data01][x]
[v][ ][Set ID][ ][NG][Data00][x]
ENGLISH
ENG
22.3D(Command: x t) (only 3D models)
11
Download PDF

advertising