LG | 71PY1M | LG 71PY1M Owner’s Manual

PLASMA
MONITOR
MODELS: 71PY1M
71PY1MG
71PY1MC
71PY1MV
OWNER’S MANUAL
Please read this manual carefully before operating your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote
this information to your dealer
when you require service.
Safety Instructions
Safety Instructions
WARNING
Do not place the set in direct sunlight or near heat sources such as heat registers, stove and so on.
- This may cause a fire.
Do not use the set in damp place such as a bathroom or any place where it is likely to get wet.
- This may cause a fire or could give an electric shock.
Bend antenna cable between inside and outside building to prevent rain from flowing in.
- This may cause water damaged inside the set and could give an electric shock.
Earth wire should be connected.
- If the earth wire is not connected, there is possible a danger of electric shock caused by the current leakage.
- If grounding methods are not possible, a separate circuit breaker should be employed and installed by a qualified electrician.
- Do not connect ground to telephone wires, lightning rods or gas pipe.
Do not place anything containing liquid on top of the set.
- This may cause a fire or could give an electric shock.
Do not insert any object into the exhaust vent.
- This may cause a fire or could give an electric shock.
Do not place heavy objects on the set.
- This may cause serious injury to a child or adult.
Do not use water while cleaning the set.
- This may cause damaged the set or could give an electric shock.
In case of smoke or strange smell from the set, switch it off ,unplug it from the wall outlet and contact your dealer
or service center.
- This may cause a fire or could give an electric shock.
Do not attempt to service the set yourself. Contact your dealer or service center.
- This may cause damaged the set or could give an electric shock.
During a lightning thunder, unplug the set from the wall outlet and don’t touch an antenna cable.
- This may cause damaged the set or could give an electric shock.
WARNING/CAUTION
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
2 Plasma Monitor
Safety Instructions
ENGLISH
* Safety instructions have two kinds of information, and each meaning of it is as below.
WARNING The violation of this instruction may cause serious injuries and even death.
NOTES
The violation of this instruction may cause light injuries or damage of the
product.
Take care of danger that may happen under specific condition.
NOTES
Never touch the power plug with a wet hand.
- This may cause an electric shock.
Disconnect from the mains and remove all connections before moving.
Do not place the set in a built-in installation such as a bookcase or rack.
- Ventilation required.
When installing the set on a table, be careful not to place the edge of its stand.
- This may cause the set to fall, causing serious injury to a child or adult, and serious damage to the set.
Do not place an outside antenna in the vicinity of overhead power lines or other electric light or power circuits.
- This may cause an electric shock.
There should be enough distance between an outside antenna and power lines to keep the former from touching the
latter even when the antenna falls.
- This may cause an electric shock.
Do not pull the cord but the plug when unplugging.
- This may cause a fire.
Ensure the power cord doesn’t trail across any hot objects like a heater.
- This may cause a fire or an electric shock.
Do not plug when the power cord or the plug is damaged or the connecting part of the power outlet is loose.
- This may cause a fire or an electric shock.
Dispose of used batteries carefully to protect a child from eating them.
- In case that it eats them, take it to see a doctor immediately.
When moving the set assembled with speakers do not carry holding the speakers.
- This may cause the set to fall, causing serious injury to a child or adult, and serious damage to the Monitor.
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
- This may cause damaged the set or could give an electric shock.
Contact the service center once a year to clean the internal part of the set.
- Accumulated dust can cause mechanical failure.
The distance between eyes and the screen should be about 5 ~ 7 times as long as diagonal length of the screen.
- If not, eyes will strain.
Unplug the set from the wall outlet when it is left unattended and unused for long periods of time.
- Accumulated dust may cause a fire or an electric shock from
deterioration or electric leakage.
Owner’s Manual 3
Safety Instructions
Safety Instructions continued
CAUTION concerning the Power Cord :
- Most appliances recommend they be connected to a dedicated circuit; that is,
a single outlet circuit which powers only that appliance and has no additional
outlets or branch circuits.
- This may cause a fire or an electric shock.
- Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords,
or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire.
Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer.
- Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
- Use a dedicated power cord. Do not modify or extend the power cord.
- Do not install, remove, or reinstall the unit by yourself (customer).
For electrical work, contact the dealer, seller, a qualified electrician, or an Authorized Service Center. For installation, always
contact the dealer or an Authorized Service Center.
- Do not use if the power cord or plug is damaged, or socket is loose. Use a dedicated outlet for this appliance.
- Do not over bend the power cord and do not place anything on the power cord. Do not install the monitor near any sharp
edge to avoid wire damage.
Outdoor Use Marking :
- WARNING - To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Appliance To Rain Or Moisture.
Wet Location Marking :
- Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on
the apparatus.
Safety instruction (71PY1MG only)
-
When the trim becomes dirty or stained, softly polish the surface.
When polishing the surface, use gentle pressure. Heavy pressure can damage or discolor the surface.
When polishing the surface, use a soft cloth with the alcohol. If not, it may cause damage or discolor the surface.
Clean the surface quickly and use gentle pressure. Heavy pressure can damage or discolor the surface.
Do not use anything to scrape or scratch at the surface of this unit, this will cause damage to the surface.
Use soft gloves while installing or removing this unit to prevent damaging the surface.
4 Plasma Monitor
Contents
ENGLISH
Contents
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2~4
Introduction
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Controls and Connection Options . . . . . . . . . .8~9
Remote Control Key Functions . . . . . . . . . .10~11
Installation
Installation Instructions . . . . . . . . . . . . . . . . . . . . .12
External Equipment Connections . . . . . . . . . .13~17
VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Cable TV Setup . . . . . . . . . . . . . . . . . . . . . . . .14
External A/V Source Setup . . . . . . . . . . . . . . . .14
DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
DTV Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . .16~17
Operation
Turning on the Monitor . . . . . . . . . . . . . .
Menu Language Selection . . . . . . . . . . .
Picture Menu Options
Auto Picture Control (APC) . . . . . . . . .
XD . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto Color Temperature Control . . . . .
Manual Color Temperature Control . . .
Fleshtone . . . . . . . . . . . . . . . . . . . . .
sRGB . . . . . . . . . . . . . . . . . . . . . . . .
Manual Picture Control . . . . . . . . . . .
Sound Menu Options
DASP (Digital Auto Sound Processing)
Manual Sound Control . . . . . . . . . . . .
BBE . . . . . . . . . . . . . . . . . . . . . . . . . .
AVL (Auto Volume Leveler) . . . . . . . . .
Timer Menu Options
Clock Setup . . . . . . . . . . . . . . . . . . . .
On/Off Timer Setup . . . . . . . . . . . . . .
Auto Off . . . . . . . . . . . . . . . . . . . . . . .
Sleep Timer . . . . . . . . . . . . . . . . . . . .
Special Menu Options
Key Lock . . . . . . . . . . . . . . . . . . . . . .
ISM Method . . . . . . . . . . . . . . . . . . . .
Low power . . . . . . . . . . . . . . . . . . . . .
Index . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . .18
. . . . . . .18
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.19
.19
.19
.19
.20
.20
.21
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.22
.22
.23
.23
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.24
.24
.25
.25
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.26
.26
.27
.27
Screen Menu Options
Auto Adjustment . . . . .
Setting Picture Format
Cinema Mode Setup . .
Screen Position . . . . .
Manual Configure . . . .
Initializing . . . . . . . . . .
Black level adj. . . . . . .
PC/DTV Mode . . . . . .
Screen Adjustments . .
NR(Noise Reduction) .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PIP (Picture-in-Picture) Feature
Watching PIP . . . . . . . . . . . . . . . . . . . . . . .
PIP Size . . . . . . . . . . . . . . . . . . . . . . . . . . .
PIP Transparency . . . . . . . . . . . . . . . . . . . .
Moving the PIP . . . . . . . . . . . . . . . . . . . . . .
Selecting an Input Signal Source for the PIP
DW Setup Options
Watching DW . . . . . . . . . . . . . . . . . . . . . . .
Sub Picture Size Adjustment . . . . . . . . . . . .
Swapping the DW . . . . . . . . . . . . . . . . . . . .
Selecting a Source for the DW . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.28
.28
.29
.29
.30
.30
.31
.31
.32
.32
.
.
.
.
.
.
.
.
.
.
.33
.33
.33
.33
.33
.
.
.
.
.
.
.
.
.34
.34
.34
.34
External Control Device Setup . . . . . . . . . . . . . . . .35~40
IR Code
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41~42
Programming the remote . . . . . . . . . . . . . . . . . . . . . . .43
Programming Codes . . . . . . . . . . . . . . . . . . . . . . . .44~45
Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . .46
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . .47
After reading this manual, keep it handy for future reference.
Owner’s Manual 5
Introduction
Introduction
What is a Plasma Display Panel?
If voltage is applied to gas within glass panels, ultraviolet rays are produced and fused with a fluorescent substance. At that
instant, light is emitted. A Plasma Display is a next generation flat Display using this phenomenon.
160° - Wide angle range of vision
Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is
clear and visible to viewers anywhere in the room.
Wide Screen
The screen of the Plasma Display is 71" so wide that your viewing experience is as if you are in a theater.
Multimedia
Connect your plasma display to a PC and you can use it for conferencing, games, and internet browsing. The Picture-in-Picture
feature allows you to view your PC and video images simultaneously.
Versatile
The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs would
not fit.
The Plasma Monitor Manufacturing Process: Why minute colored dots may be present on the Plasma
Monitor screen
The Plasma Display Panel which is the display device of this product is composed of 0.9 to 2.2 million cells. A few cell defects will
normally occur in the Plasma Monitor manufacturing process. Several minute colored dots visible on the screen should be acceptable. This also occurs in other Plasma Monitor manufacturers' products and the tiny dots appearing does not mean that this
Plasma Monitor is defective. Thus a few cell defects are not sufficient cause for the Plasma Monitor to be exchanged or returned.
Our production technology is designed to minimize cell defects during the manufacture and operation of this product.
Cooling Fan Noise
In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the Plasma Monitor is
equipped with cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the
fans are operating and cooling the Plasma Monitor.
The fan noise doesn't have any negative effect on the Plasma Monitor's efficiency or reliability. The noise from these fans is normal during the operation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable
and is not sufficient cause for the Plasma Monitor to be exchanged or returned.
WARNING
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
6 Plasma Monitor
Introduction
ENGLISH
Accessories
Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer
where you purchased the product.
MODE
LIGHT
POWER
PIP
INPUT
DW
DASP
APC
MUTE
SLEEP
VOL
CH
WIN. POSITION SWAP
WIN. SIZE
ENTER
EXIT
MENU
PIP INPUT
PLAY
REW
Owner’s Manual
Batteries
PAUSE
ARC
STOP RECORD
FF
VIDEO
COM1
HDMI1
HDMI2
SKIP
COM2
KEY LOCK
RGB
INDEX
D-sub 15 pin cable
Remote Control
Slightly wipe stained spot on the
exterior only with the cleansing
cloths for the product exterior if
there is stain or fingerprint on
surface of the exterior.
2- ferrite cores
(for the speaker cables)
Power Cord
Polishing Cloth
Polish the screen with the
cloth.
(71PY1MG only)
Do not wipe roughly when
removing stain. Please be cautious of that excessive power
may cause scratch or discoloration.
Use the ferrite core with the speaker cables
The ferrite core given as a bundled accessory can be used to reduce the electromagnetic
waves in the connection to the speakers.
Wind the speaker cable on the ferrite core twice, and then plug the cables into the monitor
and the speakers as shown in the following picture:
Option Extras
-
Optional extras can be changed or modified for quality improvement without any notification new optional extras can be added.
Contract your dealer for buying these items.
Tilt wall mounting bracket
Video cables
Desktop stand
Audio cables
Owner’s Manual 7
Introduction
Controls
- Here shown may be somewhat different from your set.
Front Panel Controls
INDEX
Switches
LED Display
on or off.
INPUT
VOL
MENU
Sub power Button
E, D
Buttons
Remote
Control
Sensor
VOLUME (F,G) Buttons
Power Indicator
Illuminates red in standby
mode, Illuminates green when
the monitor is turned on.
MENU Button
INPUT Button
INDEX
Video Mode
Flat G p.22
Component Mode
Music G p.22
RGB(DTV/PC) Mode
Movie G p.22
HDMI1/DVI or HDMI2 Mode
Sports G p.22
Off G p.22
8 Plasma Monitor
Introduction
ENGLISH
Connection Options
- Here shown may be somewhat different from your set.
Back Connection Panel
(MONO)
VIDEO
AUDIO
S-VIDEO
VIDEO IN
AUDIO
VIDEO
COMPONENT IN
VIDEO IN 3
HDMI/DVI IN
2
RGB IN
RS-232C IN
(CONTROL & SERVICE)
SERVICE)
VIDEO IN 4
REMOTE
CONTROL IN
AUDIO (RGB/DVI)
1
RGB(PC/DTV)
R
L
EXTERNAL SPEAKER
AC IN
4
3
(MONO)
VIDEO
AUDIO
VIDEO IN
S-VIDEO
AUDIO
VIDEO
COMPONENT IN
5
VIDEO IN 3
1
HDMI IN
2
VIDEO IN 4
2
RS-232C IN
(CONTROL & SER
SERVICE)
VICE)
1(DVI)
9
8
RGB IN
REMOTE
CONTROL IN
AUDIO (RGB/DVI)
RGB(PC/DTV)
R
EXTERNAL SPEAKER
6
1 HDMI IN
Connect a HDMI signal to 1(DVI) or 2.
Or DVI(VIDEO) signal to the 1(DVI) port with a DVI to
HDMI cable.
2 RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
3 VIDEO IN
Connect audio/video output from an external device to
these jacks.
S-VIDEO
Connect S-Video out from an S-VIDEO device.
4 COMPONENT IN
Connect a component video/audio device to these jacks.
5 EURO SCART SOCKET
Connect the euro scart of the VCR to these sockets.
L
AC IN
7
6 RGB IN
AUDIO (RGB/DVI)
Connect the monitor output from a PC to the appropriate
input port.
RGB(PC/DTV)
Connect the monitor output from a PC to the appropriate
input port.
7 Remote Control Port
Connect your wired remote control.
8 EXTERNAL SPEAKER (8 ohm output)
Connect to optional external speaker(s).
* For further information, refer to ‘Speaker & Speaker
Stand’ manual.
9 POWER CORD SOCKET
This Monitor operates on an AC power. The voltage is
indicated on the Specifications page. Never attempt to
operate the Monitor on DC power.
Owner’s Manual 9
Introduction
Remote Control Key Functions
- When using the remote control, aim it at the remote control sensor on the monitor.
- Under certain conditions such as if the remote IR signal is interrupted, the remote control may not function. Press
the key again as necessary.
LIGHT
Illuminates the remote control buttons.
LIGHT
MODE
POWER
INPUT
PIP
DW
DASP
APC
MUTE
SLEEP
VOL
MODE
Selects the remote operating mode: MNT, VCR, DVD, CABLE,
HDSTB or AUDIO.
POWER
Turns your monitor or any other programmed equipment on or
off, depending on mode.
INPUT
Selects: Video1-2-3-4, Component 1-2, RGB(DTV/PC),
HDMI1/DVI, HDMI2 input sources.
PIP
Selects the PIP mode.
DW
Selects the DW mode.
CH
WIN. POSITION SWAP
WIN. SIZE
NUMBER buttons
Dosen’t work for monitor mode.
ENTER
EXIT
MENU
PIP INPUT
ARC
PLAY
PAUSE
STOP RECORD
REW
FF
SKIP
WIN. SIZE
Adjusts the sub picture size.
WIN.POSITION
Moves the sub picture.
SWAP
Exchanges the main/sub images.
VIDEO
COM1
HDMI1
HDMI2
COM2
KEY LOCK
RGB
INDEX
XD
Switches the XD on or off. (Refer to p. 19)
MENU
Brings up the main menu to the screen.
PIP INPUT
Selects the input source for the sub picture.
ARC
Changes the picture format. (Refer to p. 28)
EXIT
Clears all on-screen displays and returns to monitor viewing
from any menu.
10 Plasma Monitor
Introduction
ENGLISH
APC
Adjusts the factory preset picture according to the room.
Daylight, Optimum, Night time or Off (Refer to p.19)
LIGHT
MODE
POWER
INPUT
PIP
DW
DASP
To select the sound appropriate to your viewing program character:
SRS TSXT, Flat, Music, Movie, Sports, or Off
(Refer to p.22)
MUTE
Switches the sound on or off.
DASP
APC
MUTE
SLEEP
VOL
CHANNEL UP/DOWN
Selects available channels.
Dosen’t work for monitor mode.
WIN. SIZE
THUMBSTICK (Up/Down/Left/Right/ENTER)
Navigate the on-screen menus and adjust the system settings
to your preference.
ENTER
EXIT
MENU
ARC
PLAY
PAUSE
STOP RECORD
REW
FF
SKIP
VIDEO
COM1
HDMI1
HDMI2
VOLUME UP/DOWN
Increases/decreases the sound level.
CH
WIN. POSITION SWAP
PIP INPUT
SLEEP
Sets the Sleep Timer.
COM2
KEY LOCK
RGB
INDEX
VCR/DVD/DVHS/Camcorder BUTTONS
Control some video cassette recorders or DVD players
("RECORD" button is not available for DVD player).
VIDEO/COM1/COM2/RGB/HDMI1/DVI/HDMI2
Selects: Video1-2-3-4, Component 1-2, RGB(DTV/PC),
HDMI1/DVI, HDMI2 input sources.
KEY LOCK
Switches the key lock on or off.
INDEX
Switches LED Display on or off.
Installing Batteries
• Open the battery compartment cover on the back side and install the batteries
matching correct polarity (+ with +, - with -).
• Install two 1.5V AA batteries. Don’t mix old or used batteries with new ones.
Replace cover.
Owner’s Manual 11
Installation
Installation
Installation Instructions
• Install this monitor only in a location where adequate ventilation is available.
GROUNDING
Power
Supply
Ensure that you connect the grounding / earth wire to prevent possible
electric shock. If grounding methods are not possible, have a qualified
electrician install a separate circuit breaker. Do not try to ground the
unit by connecting it to telephone wires, lightening rods, or gas pipes.
Short-circuit
Breaker
Wall Mount Installation
For proper ventilation, allow a clearance of 4” on each
side and 4” from the wall. Detailed installation instructions are available from your dealer, see the optional
Wall Mounting Bracket Installation and Setup Guide.
4 inches
4 inches
4 inches
4 inches
4 inches
Desktop Pedestal Installation
For proper ventilation, allow a clearance of 4” on each
side and the top and 4” from the wall. Detailed installation instructions are included in the optional Desktop
Stand Installation and Setup Guide available from your
dealer.
4 inches
4 inches
12 Plasma Monitor
4 inches
4 inches
Installation
ENGLISH
External Equipment Connections
NOTE: Not all cables shown are included with the plasma display.
VCR Setup
- To avoid picture noise (interference), leave an adequate distance between the VCR and Monitor.
- Use the ISM Method feature to avoid having a fixed image remain on the screen for a long period of time. Typically a frozen
still picture from a VCR. If the 4:3 picture format is used; the fixed image may remain visible on the screen.
How to connect
1. Connect the audio and video cables from the VCR's output
jacks to the monitor input jacks, as shown in the figure.
When connecting the monitor to VCR, match the jack colors
(Video = yellow, Audio Left = white, and Audio Right = red).
2. If you connect an S-VIDEO output from VCR to the SVIDEO input, the picture quality is improved; compared to
connecting a regular VCR to the Video input.
3. If you connect the Euro scart socket of the VCR to the Euro
scart socket of the set. No other connection is needed.
(MONO)
VIDEO
AUDIO
VIDEO
S-VIDEO
AUDIO
COMPONENT IN
VIDEO IN
VIDEO IN 3
Mono VCR: Connect the video output cable from the VCR
to the VIDEO input on the monitor.
S-VIDEO VCR: Connect the S-Video output cable from the
VCR to the S-VIDEO input on the monitor. (Note that SVideo offers higher quality).
or
How to use
1. Insert a video tape into the VCR and press PLAY on the
VCR.
(Refer to the VCR owner’s manual.)
2. Use the INPUT button on the remote control to select
Video 1.
(If connected to VIDEO 2, VIDEO 3 or VIDEO 4, select the
Video 2, Video 3 or Video 4 input source.)
VIDEO IN 4
ANT OUT
ANT IN
VIDEO
(R) AUDIO (L)
S-VIDEO
OUT
OUTPUT
SWITCH
3
4
IN
VCR
Owner’s Manual 13
Installation
External Equipment Connections
Cable TV Setup
- After subscribing to a cable monitor service from a local provider and installing a converter, you can watch cable TV programming. The monitor cannot display monitor programming unless a TV tuner device or cable TV converter box is connected to the
Monitor.
- For further information regarding cable monitor service, contact your local cable TV service provider(s).
How to connect
1. Connect the audio and video cables from the Cable Box's output
jacks to the monitor input jacks, as shown in the figure.
When connecting the monitor to a Cable Box, match the jack colors
(Video = yellow, Audio Left = white, and Audio Right = red).
Or, connect the Euro scart socket of the Cable box to the Euro scart
socket of the set.
(MONO)
How to use
VIDEO
AUDIO
VIDEO
S-VIDEO
1. Use the INPUT button on the remote control to select Video 1.
(If connected to VIDEO 2, VIDEO 3 or VIDEO 4, select the Video 2,
Video 3 or Video 4 input source.)
2. Select your desired channel with the remote control for cable box.
VIDEO
AUDIO
COMPONENT IN
VIDEO IN
(R) AUDIO (L)
TV
VCR
RF
Cable
Cable Box
External A/V Source Setup
How to connect
1. Connect the audio and video cables from the external
equipment's output jacks to the monitor input jacks, as
shown in the figure.
When connecting the monitor to external equipment, match
the jack colors (Video = yellow, Audio Left = white, and
Audio Right = red).
Or, connect the Euro scart socket of the External A/V to the
Euro scart socket of the set.
(MONO)
VIDEO
S-VIDEO
AUDIO
AUDIO
VIDEO
COMPONENT IN
VIDEO IN
How to use
1. Use the INPUT button on the remote control to select
Video1.(If connected to VIDEO 2, VIDEO 3 or VIDEO 4,
select the Video 2, Video 3 or Video 4 input source.)
2. Operate the corresponding external equipment. Refer to
external equipment operating guide.
Camcorder
VIDEO
R
AUDIO
L
Video Game Set
14 Plasma Monitor
Installation
ENGLISH
DVD Setup
HDMI IN
2
HDMI IN
RS-232C IN
(CONTROL & SERVICE)
(
VIDEO
RS-232C IN
(CONTROL & SERVICE)
2
VIDEO
(
1(DVI)
VIDEO
AUDIO
VIDEO IN
)
VIDEO
S-VIDEO
AUDIO
VIDEO
AUDIO
AU
VIDEO
S-VIDEO
AUDIO
AUDIO
VIDEO
S-VIDEO
VIDEO
S-VIDEO
COMPONENT IN
AUDIO
COMPONENT IN
VIDEO IN
COMPONENT IN
)
AUDIO
VIDEO IN
(MONO)
(MONO)
1(DVI)
AUDIO
COMPONENT IN
VIDEO IN
or
or
HDMI OUTPUT
(R) AUDIO (L)
B
S-VIDEO
R
(R) AUDIO (L)
DVD
How to connect
1. Connect the DVD video outputs to the COMPONENT (Y, PB, PR) or HDMI IN 1(DVI) jacks and connect the
DVD audio outputs to the AUDIO INPUT jacks on the monitor, as shown in the figure.
2. If your DVD only has an S-Video output jack, connect this to the S-VIDEO input on the monitor and connect the
DVD audio outputs to the AUDIO INPUT jacks on the monitor, as shown in the figure.
How to use
1. Turn on the DVD player, insert a DVD.
2. Use the INPUT button on the remote control to select Component 1, Component 2, HDMI1/DVI or HDMI2.
(If connected to S-VIDEO, select the Video 1 external input source.)
3. Refer to the DVD player's manual for operating instructions.
RGB IN
HDMI IN
RS-232C IN
(CONTROL & SERVICE)
2
AUDIO (RGB/DVI)
RGB(PC/DTV)
1
Component ports of the
Monitor
• Component Input ports
To get better picture quality, connect a DVD
player to the component input ports as shown.
Video output ports
of DVD player
PR
Y
PB
Y
Y
Y
Y
Pr
Pb
B-Y R-Y
Cb Cr
PB PR
DTV Setup
- To watch digitally broadcast programs, purchase and connect a digital set-top box.
- This monitor supports HDCP (High-bandwidth Digital Contents Protection) protocol for
HDMI/DVI-DTV (480p,576p,720p,1080i, 1080p) mode.
RGB IN
RGB IN
HDMI IN
HDMI IN
RS-232C IN
(CONTROL & SERVICE)
2
2
AUDIO (RGB/DVI)
RS-232C IN
(CONTROL & SERVICE)
REMOTE
CONTROL IN
AUDIO (RGB/DVI)
(MONO)
1(DVI)
VIDEO
1
AUDIO
VIDEO
S-VIDEO
AUDIO
COMPONENT IN
VIDEO IN
RGB(PC/DTV)
RGB(PC/DTV)
1
or
HDMI OUTPUT
DVI-DTV OUTPUT
(R) AUDIO (L)
or
RGB-DTV OUTPUT
or
(R) AUDIO (L)
HDMI OUTPUT
RGB-DTV OUTPUT
B
R
(R) AUDIO (L)
Digital Set-top Box
How to connect
1. Use the monitor’s COMPONENT (Y, PB, PR) INPUT, RGB or HDMI IN 1(DVI) to HDMI jack for video connections, depending on your set-top box connector. Then, make the corresponding audio connections.
RGB IN
HDMI IN
2
RS-232C IN
(CONTROL & SERVICE)
How to use
REMOTE
CONTROL IN
AUDIO (RGB/DVI)
(
VIDEO
1
RGB(PC/DTV)
)
AUDIO
VIDEO IN
S-VIDEO
VIDEO
AUDIO
COMPONENT IN
1. Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)
2. Use INPUT on the remote control to select Component 1, Component 2, RGB, HDMI1/DVI or HDMI2.
Owner’s Manual 15
Installation
External Equipment Connections
PC Setup
- This monitor provides Plug and Play capability, meaning that the PC adjusts automatically to its settings. The monitor sends
configuration information (EDID) to the PC using the Video Electronics Standard Association (VESA) Display Data Channel
(DDC) protocol.
- The monitor perceives 640x480, 60Hz as DTV 480p based on the PC graphic card. In this case, change the screen scanning
rate for the graphic card.
How to connect
1. To get the best picture quality, adjust the PC
graphics card to a 1600x1200, 60Hz.
2. Use the monitor’s RGB IN or HDMI IN 1(DVI) port
for video connections, depending on your PC connector.
If the graphic card on the PC does not output analog and digital RGB simultaneously, connect only
one of either RGB IN or HDMI IN 1(DVI) to display
the PC on the monitor.
If the graphic card on the PC does output analog
and digital RGB simultaneously, set the monitor to
either RGB or HDMI1/DVI; (the other mode is set
to Plug and Play automatically by the monitor.)
3. Then, make the corresponding audio connections.
If using a sound card, adjust the PC sound as
required.
RGB IN
HDMI IN
2
RS-232C IN
(CONTROL & SER
SERVICE)
VICE)
REMOTE
CONTROL IN
AUDIO (RGB/DVI)
1(DVI)
RGB(PC/DTV)
How to use
1. Turn on the PC and the monitor.
2. Turn on the display by pressing the POWER button on the monitor's remote control.
3. Use the INPUT button on the remote control to select RGB or HDMI1/DVI.
4. Check the image on your monitor. There may be noise associated with the resolution, vertical pattern, contrast or
brightness in PC mode. If noise is present, change the PC mode to another resolution, change the refresh rate to
another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC
graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.
NOTES: • Avoid keeping a fixed image on the monitor's screen for a long period of time. The fixed image may become
permanently imprinted on the screen. Use the Orbiter screen saver when possible.
• The synchronization input form for Horizontal and Vertical frequencies is separate.
16 Plasma Monitor
Installation
Resolution
720x400
640x480
800x600
832x624
1024x768
1280x1024
1600x1200
1920x1080
ENGLISH
Monitor Display Specifications (RGB-PC / HDMI/DVI-PC Mode)
Horizontal
Vertical
Frequency(kHz) Frequency(Hz)
31.469
70.08
31.469
59.94
35.000
66.66
37.861
72.80
37.500
75.00
43.269
85.00
37.879
60.31
46.875
75.00
53.674
85.06
49.725
74.55
48.363
60.00
56.476
70.06
60.023
75.02
63.981
60.02
80.000
75.00
75.00
60.00
66.587
59.934
- HDMITM, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing."
- This monitor can receive the High-Definition Multimedia
Interface(HDMI).
- This monitor supports HDCP(High-bandwidth Digital
Contents Protection) Protocol for 480p,576p,720p,1080i,
1080p modes.
- When you Connect with HDMI Source Devices (DVD Player
or Set Top Box) supporting Auto HDMI function, automatically, support Plug & Play and then set the HDMI Source
Devices(1920 x 1080i). After reading in HDMI Source Devices
using Display Data Channel(DDC) Protocol, EDID stored in
monitor is used. If HDMI Source Devices not supported Auto
HDMI is been, the Resolution is setted, manually.
- To get the best picture quality, adjust the DVD Player or Set
Top Box output resolution to 1920 x 1080i.
How to connect
When Source Devices(DVD Player or Set Top Box) support
HDMI.
- If Source Devices have HDMI Output Connector, Source
Devices connect to DTV with HDMI Cable.(not supplied with
the product).
- If Source Devices support Auto HDMI, automatically, Source
Devices divert output resolution in 1920 x 1080i. But if not,
resolution divert Manually Setting for reference Manual of
Source Devices.
- To get the best picture quality, adjust the DVD Player or Set
Top Box output resolution to 1920 x 1080i.
- Because HDMI sends Digital Video and Audio with one cable,
need not especial Audio Cable for using HDMI Cable.
Owner’s Manual 17
Operation
Operation
Turning on the Monitor
Turning on the Monitor just after installation
1. Connect power cord correctly. At this moment, the Monitor is switched to standby mode.
2. Press the INPUT or
button on the Monitor or press the POWER, INPUT button on the remote
control and then the Monitor will switch on.
Menu Language Selection
- The menus can be shown on the screen in the selected language. First select your language.
1. Press the MENU button and then use
2. Press the G button and then use D /
E
D
/
E
button to select the SPECIAL menu.
button to select Language.
3. Press the G button and then use D / E button to select your desired language.
From this point on, the on-screen menus will be shown in the language of your choice.
4. Press the ENTER button to save.
• Press the MENU button to return to the previous menu.
18 Plasma Monitor
Operation
ENGLISH
Picture Menu Options
- Readjust Picture menu settings for each following input source as preferred.
Auto Picture Control (APC)
- APC adjusts the Monitor for the best picture appearance.
- When adjusting Picture menu options (contrast, brightness, color, sharpness, and tint) manually, APC automatically changes to Off.
1. Press the APC button repeatedly to select the picture appearance setup option as shown below.
Daylight
Optimum
Night time
Off
• You can also select Daylight, Optimum, Night time or Off in the PICTURE menu.
• Daylight, Optimum, and Night time settings are preset for optimum picture quality at the factory and cannot be
changed.
XD
- XD is LG Electronic’s unique picture improving technology to display a real HD
source through an advanced digital signal processing algorithm.
- When selecting APC options (Daylight, Optimum and Night time), XD is automatically change to On.
1. Press the
button repeatedly as shown below.
On
Off
Auto Color Temperature Control
- To initialize values (reset to default settings), select the Cool option.
PICTURE
PICTURE
APC
ACC
TIMER
SPECIAL
TIMER
PIP/DW
Move
SPECIAL
100
Brightness
55
Color
55
Sharpness
60
Tint
55
PIP/DW
Color
55
Sharpness
60
Move
button and then use
D /E
D /E
100
Brightness
Tint
Select
G
Contrast
SCREEN
0
1. Press the MENU button and then use
2. Press the
G
ACC
Fleshtone
Fleshtone
Contrast
SCREEN
APC
SOUND
SOUND
0
Cool
Normal
Warm
Off
Red
0
Green
0
Blue
0
Select
button to select the PICTURE menu.
button to select ACC .
3. Press the G button and then use D / E button to select either Cool (Default), Normal
(Preset) and Warm (Preset), Off (Preset).
4. Press the ENTER button to save the new settings.
Manual Color Temperature Control (A
(ACC set to Off option)
- You can adjust red, green, or blue to any color temperature you prefer.
1. Press the MENU button and then use
D /E
button to select the PICTURE menu.
2. Press the
G
button and then use
3. Press the
G
button and then use D
/E
button to select Off.
4. Press the
G
button and then use D
/E
button to select Red, Green or Blue.
5. Use the
F / G button
D /E
button to select ACC .
to make appropriate adjustments.
• The adjustment range of Red, Green and Blue is -10 ~ +10.
6. Press the ENTER button to save the new settings.
Owner’s Manual 19
Operation
Picture Menu Options continued
Fleshtone (Video1-2-3-4,
(Video1-2-3-4, Component 1-2, RGB-DTV,
RGB-DTV, HDMI1/DVI-DTV,
HDMI1/DVI-DTV, HDMI2-DTV Mode only)
- Use Fleshtone to select the desired skin color option.
PICTURE
PICTURE
APC
SOUND
ACC
TIMER
SPECIAL
SCREEN
PIP/DW
TIMER
Contrast
ACC
Fleshtone
Fleshtone
SPECIAL
100
Brightness
55
Color
55
Sharpness
60
Tint
Move
APC
SOUND
Contrast
SCREEN
Brightness
55
PIP/DW
Color
55
Sharpness
60
Tint
0
Select
Move
1. Press the MENU button and then use D
/E
0
G
100
0
Select
button to select the PICTURE menu.
2. Press the G button and then use
D
3. Press the G button and then use
F / G button
/ E button to select Fleshtone.
to make appropriate adjustments.
• The adjustment range is 0 ~ 3.
4. Press the ENTER button to save the new settings.
sRGB (only RGB-PC, HDMI1/DVI-PC Modes)
- If the monitor is connected to external equipment using sRGB, set sRGB to On to adjust for the color difference.
PICTURE
PICTURE
APC
SOUND
ACC
TIMER
SPECIAL
SCREEN
PIP/DW
Move
TIMER
sRGB
Contrast
SPECIAL
100
Brightness
55
SCREEN
Color
55
PIP/DW
Move
1. Press the MENU button and then use D
2. Press the G button and then use
D
3. Press the
D /E
button and then use
/E
Select
button to select the PICTURE menu.
/ E button to select sRGB.
button to select On or Off.
4. Press the ENTER button to save the new settings.
20 Plasma Monitor
ACC
sRGB
Contrast
Select
G
APC
SOUND
G
100
Brightness
55
Color
55
On
Off
Operation
ENGLISH
Manual Picture Control (Off
(Off option)
- You can adjust picture contrast, brightness, color, sharpness, and tint to the levels you prefer.
PICTURE
PICTURE
APC
SOUND
TIMER
SPECIAL
ACC
PIP/DW
Brightness
SPECIAL
100
SCREEN
55
Color
55
Sharpness
60
Tint
Move
TIMER
Fleshtone
Contrast
SCREEN
APC
SOUND
PIP/DW
ACC
Fleshtone
Contrast
60
Color
50
Sharpness
50
Tint
0
Select
Move
1. Press the MENU button and then use
menu.
D / E
100
Brightness
G
0
Select
button to select the PICTURE
2. Press the G button and then use D / E button to select the desired picture
option (Contrast, Brightness, Color, Sharpness or Tint).
3. Press the G button and then use F
/ G button
to make appropriate adjustments.
4. Press the ENTER button to save the new settings.
Owner’s Manual 21
Operation
Sound Menu Options
DASP (Digital Auto Sound Processing)
- DASP lets you enjoy the best sound without any special adjustment because the Monitor has the appropriate
sound options based on the program content.
- When adjusting sound options (treble, bass) manually, DASP automatically changes to Off.
1. Press the DASP button repeatedly to select the appropriate sound setup as shown below.
SRS TSXT
Flat
Music
Movie
Off
Sports
• You can also adjust DASP in the SOUND menu.
• SRS TSXT, Flat, Music, Movie, and Sports are preset for good sound quality at the factory and cannot be changed.
•
is a trademark of SRS Labs, Inc.
• TruSurround XT technology is incorporated under license from SRS Labs, Inc.
Manual Sound Control (Dasp Off option and balance)
PICTURE
DASP
PICTURE
DASP
SOUND
BBE
SOUND
BBE
TIMER
AVL
TIMER
SPECIAL
Balance
SCREEN
0
Treble
50
Bass
50
SPECIAL
SCREEN
PIP/DW
Move
AVL
G
Balance
Treble
50
Bass
50
L
PIP/DW
Select
Move
1. Press the MENU button and then use D
/E
Select
button to select the SOUND menu.
2. Press the G button and then use
D /E
button to select the desired sound option (Balance, Treble or Bass).
3. Press the
F /G
button to make appropriate adjustments.
G
button and then use
4. Press the ENTER button to save the new settings.
22 Plasma Monitor
R
Operation
ENGLISH
BBE
- BBE High Definition Sound restores clarity and presence for better speech intelligibility and musical realism.
PICTURE
DASP
PICTURE
DASP
SOUND
BBE
SOUND
BBE
TIMER
AVL
TIMER
SPECIAL
Balance
SCREEN
0
Treble
50
Bass
50
SPECIAL
SCREEN
PIP/DW
Move
Balance
On
Off
0
Treble
50
Bass
50
PIP/DW
Select
Move
1. Press the MENU button and then use D
/E
D /E
button to select BBE.
3. Press the
D /E
button to select On or Off.
button and then use
Select
button to select the SOUND menu.
2. Press the G button and then use
G
G
AVL
4. Press the ENTER button to save the new settings.
•
Manufactured under license from BBE Sound, Inc.
• Treble, Bass or BBE aren’t suitable for SRS TSXT mode.
AVL (Auto Volume
Volume Leveler)
- This feature maintains an equal volume level; even if you change channels.
PICTURE
PICTURE
DASP
DASP
SOUND
BBE
SOUND
BBE
TIMER
AVL
TIMER
AVL
SPECIAL
Balance
SCREEN
0
Treble
50
Bass
50
SPECIAL
SCREEN
PIP/DW
Move
Balance
G
0
Treble
50
Bass
50
On
Off
PIP/DW
Select
Move
1. Press the MENU button and then use
D /E
Select
button to select the SOUND menu.
2. Press the
G
button and then use
D /E
button to select AVL.
3. Press the
G
button and then use
D /E
button to select On or Off.
4. Press the ENTER button to save the new settings.
Owner’s Manual 23
Operation
T imer Menu Options
Clock Setup
- If current time setting is wrong, correct the clock setting.
PICTURE
Clock
PICTURE
Clock
SOUND
Off timer
SOUND
Off timer
TIMER
On timer
SPECIAL
TIMER
Auto off
SPECIAL
SCREEN
SCREEN
PIP/DW
PIP/DW
Move
Select
Move
1. Press the MENU button and then use
G
-- :
--
AM
On timer
Auto off
Select
button to select the TIMER menu.
D /E
/ E button to select Clock.
2. Press the
G
button and then use
D
3. Press the
G
button and then use
D /E
button to set the hour.
4. Press the
G
button and then use
D /E
button to set the minutes.
5. Press the ENTER button to save the new settings.
On/Off
On/Off Timer Setup
- Timer function operates only if current time has already been set.
- Off-Timer function overrides On-Timer function if they are set to the same time.
- If you do not press any button within 2 hours after the monitor turns on with the On Timer function, the monitor will
automatically revert to standby mode.
PICTURE
Clock
PICTURE
Clock
SOUND
Off timer
SOUND
Off timer
TIMER
On timer
TIMER
On timer
SPECIAL
Auto off
SPECIAL
SCREEN
SCREEN
PIP/DW
PIP/DW
Move
Select
Move
1. Press the MENU button and then use
2. Press the
G
button and then use
D /E
D /E
G
Auto off
Select
button to select the TIMER menu.
button to select Off timer or On timer.
3. Press the G button and then use D / E button to select On.
• To cancel On/Off timer function, select Off.
4. Press the
G
button and then use
D /E
button to set the hour.
5. Press the
G
button and then use
D /E
button to set the minutes.
For only On timer function; Press the
G
button and then use
6. Press the ENTER button to save the new settings.
24 Plasma Monitor
D /E
button to set volume level.
On
Off
6
: 30 AM
Volume
17
Operation
ENGLISH
Auto Off
Off
- If there is no input signal, the Monitor turns off automatically after 10 minutes.
PICTURE
Clock
PICTURE
Clock
SOUND
Off timer
SOUND
Off timer
TIMER
On timer
TIMER
On timer
SPECIAL
Auto off
SPECIAL
SCREEN
SCREEN
PIP/DW
PIP/DW
Move
Select
Move
1. Press the MENU button and then use
D /E
2. Press the
G
On
Off
Select
button to select the TIMER menu.
button and then use
D /E
button to select Auto off.
3. Press the G button and then use
D /E
button to select On or Off.
G
Auto off
4. Press the ENTER button to save the new settings.
Sleep Timer
- The sleep timer turns the Monitor off at a preset time. Note that this setting is cleared when the monitor is turned off.
zz
1. Press the SLEEP button repeatedly to select the number of minutes. First the
--- Min option appears on the
screen, followed by the following sleep timer options: 10, 20, 30, 60, 90, 120, 180, and 240 minutes.
2. When the number of minutes you want is displayed on the screen, press the ENTER button. The timer begins to
count down from the number of minutes selected.
3. To check the remaining minutes before the monitor turns off, press the SLEEP or ENTER button once.
4. To cancel the Sleep Timer, press the SLEEP button repeatedly until
zz
--- Min appears.
Owner’s Manual 25
Operation
Special Menu Options
Key Lock
- The monitor can be set up so that it can only be used with the remote control.
- This feature can be used to prevent unauthorized viewing by disabling the front panel controls.
- This Monitor is programmed to remember which option it was last set to even if you turn the monitor off.
PICTURE
Language
PICTURE
Language
SOUND
Key lock
SOUND
Key lock
TIMER
ISM Method
TIMER
Low power
SPECIAL
SPECIAL
SCREEN
Index
PIP/DW
Move
Select
G
Low power
Index
PIP/DW
Move
1. Press the MENU button and then use
2. Press the
On
Off
Set ID
Set ID
SCREEN
G
ISM Method
button and then use
3. Press the G button and then use
D /E
D /E
D /E
• When you select On, the display ‘
Select
button to select the SPECIAL menu.
button to select Key lock.
button to select On or Off.
W
Key lock’
appears on the screen if any button on the front panel is pressed.
4. Press the ENTER button to save the new settings.
-In setting Key lock ‘On’, if the monitor is turned off with the remote control, press the INPUT on the monitor
or POWER, INPUT on the remote control to turn the monitor on.
ISM (Image Sticking Minimization) Method
- A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in an ghost
image remaining; even when you change the image. Avoid allowing a fixed or still image to remain on the Monitor's
screen for a long period of time.
PICTURE
Language
PICTURE
Language
SOUND
Key lock
SOUND
Key lock
TIMER
ISM Method
TIMER
ISM Method
SPECIAL
Low power
SCREEN
SPECIAL
Set ID
SCREEN
Index
PIP/DW
Move
G
Normal
Low power
White wash
Set ID
Orbiter
Index
Inversion
PIP/DW
Select
Move
1. Press the MENU button and then use
D /E
Select
button to select the SPECIAL menu.
2. Press the
G
button and then use
D /E
button to select ISM Method.
3. Press the
G
button and then use
D /E
button to select either Normal, White wash, Orbiter, or Inversion.
• Normal
If image sticking is never a problem, ISM is not necessary - set this to Normal.
• White wash
White Wash removes permanent images from the screen. Note: An excessive permanent image may be impossible to clear
completely using White Wash. To return to normal viewing, press the any button.
• Orbiter
Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid a
permanent image on the screen, the image will move every 2 minutes.
• Inversion
Inversion will automatically invert the plasma display panel color every 30 minutes.
4. Press the ENTER button to save the new settings.
26 Plasma Monitor
Operation
ENGLISH
Low Power
- Low power reduces the plasma display's power consumption.
PICTURE
Language
PICTURE
Language
SOUND
Key lock
SOUND
Key lock
TIMER
ISM Method
TIMER
ISM Method
SPECIAL
Low power
SCREEN
SPECIAL
SCREEN
Index
PIP/DW
Move
Low power
G
Set ID
Set ID
On
Off
Index
PIP/DW
Select
Move
1. Press the MENU button and then use D
/E
2. Press the
G
button and then use
D /E
button to select Low power.
3. Press the
G
button and then use
D /E
button to select On or Off.
Select
button to select the SPECIAL menu.
• When you select On, the screen darkens.
4. Press the ENTER button to save the new settings.
INDEX
- Switches LED Display on or off.
PICTURE
Language
PICTURE
Language
SOUND
Key lock
SOUND
Key lock
TIMER
ISM Method
TIMER
ISM Method
SPECIAL
Low power
SCREEN
SPECIAL
SCREEN
Index
PIP/DW
Move
PIP/DW
Select
Move
1. Press the MENU button and then use
2. Press the
G
button and then use
3. Press the G button and then use
Low power
Set ID
Set ID
D /E
D /E
D /E
Index
G
On
Off
Select
button to select the SPECIAL menu.
button to select Index.
button to select On or Off.
4. Press the ENTER button to save the new settings.
Owner’s Manual 27
Operation
Screen Menu Options
Auto Adjustment
-
RGB (PC) mode only; This function doesn’t work for RGB(DTV).
Automatically adjusts picture position and minimizes image shaking.
After adjustment, if the image is still not correct, your Monitor is functioning properly but needs further adjustment.
The Auto config., Position and Manual config. are not active in HDMI/DVI mode.
PICTURE
PICTURE
Auto config.
Auto config.
SOUND
ARC
SOUND
ARC
TIMER
Cinema
TIMER
Cinema
SPECIAL
Position
SPECIAL
Manual config.
SCREEN
PIP/DW
Move
NR
PIP/DW
Reset
Position
NR
Reset
Black level adj.
Black level adj.
PC/DTV Mode
PC/DTV Mode
Select
G
button and then use
To Set
Manual config.
SCREEN
Move
1. Press the MENU button and then use
2. Press the
G
D /E
D /E
Select
button to select the SCREEN menu.
button to select Auto config..
3. Press the G button to run Auto configure.
• When Auto config. has finished, OK will be shown on screen.
• If the position of the image is still not correct, try Auto adjustment again.
4. In RGB (PC) mode, if the image needs to be adjusted more after using Auto config., you can make further adjustments
with the Manual config. option.
Setting Picture Format
-
Caution: If a 4:3 fixed image is on the screen for a long time, it may remain visible.
RGB-PC, HDMI-PC: 4:3, 16:9
Component 480i, Video sources : 4:3, 16:9, Horizon and Zoom.
RGB-DTV, HDMI-DTV/Component 480p,576p,720p,1080i,1080p/HDMI 480p,576p,720p,1080i,1080p : 4:3,
16:9 and Zoom.
1. Press the ARC button repeatedly to select the desired picture format. You can also select picture format in the
SCREEN menu.
• 4:3
- Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with black bars appearing at both
the left and right sides.
• 16:9
- Choose 16:9 when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen.
• Horizon
- Choose Horizon when you want to adjust the picture in a non-linear proportion, that is, more enlarged at both
sides, to create a spectacular view.
• Zoom
- Choose Zoom when you want to view the picture without any alteration. However, the top and bottom portions
of the picture will be cropped.
28 Plasma Monitor
Operation
ENGLISH
Cinema Mode Setup (Video1-2
(Video1-2 and Component 480i mode only)
- Sets up the monitor for the best picture appearance for viewing movies.
PICTURE
PICTURE
Auto config.
SOUND
ARC
SOUND
ARC
TIMER
Cinema
TIMER
Cinema
SPECIAL
Auto config.
Position
SPECIAL
PIP/DW
SCREEN
NR
PIP/DW
Reset
Off
NR
Reset
Black level adj.
Black level adj.
Move
On
Manual config.
Manual config.
SCREEN
G
Position
Select
Move
1. Press the MENU button and then use D
/E
Select
button to select the SCREEN menu.
2. Press the
G
button and then use
D /E
button to select Cinema..
3. Press the
G
button and then use
D /E
button to select On or Off.
4. Press the ENTER button to save the new settings.
Screen Position
- This function works in the following mode:
RGB-PC, RGB-DTV(480p,576p,720p,1080i,1080p), COMPONENT (480p,576p,720p,1080i,1080p).
PICTURE
PICTURE
Auto config.
SOUND
ARC
SOUND
ARC
TIMER
Cinema
TIMER
Cinema
SPECIAL
Auto config.
Position
SPECIAL
PIP/DW
Move
Position
G
Manual config.
Manual config.
SCREEN
SCREEN
NR
PIP/DW
Reset
NR
Black level adj.
PC/DTV Mode
PC/DTV Mode
Move
1. Press the MENU button and then use
D /E
G
E
Reset
Black level adj.
Select
D
F
Select
button to select the SCREEN menu.
2. Press the
G
button and then use
D /E
3. Press the
G
button and then use
D /E /F /G
button to select Position.
button to adjust the position.
4. Press the ENTER button to save the new settings.
Owner’s Manual 29
Operation
Screen Menu Options continued
Manual Configure (RGB-PC mode only)
- If the image still isn’t clear after auto adjustment is completed and especially if characters are still jittery, adjust the
picture Phase manually.
- To correct the screen size, adjust Clock.
PICTURE
Auto config.
PICTURE
Auto config.
SOUND
ARC
SOUND
ARC
TIMER
Cinema
TIMER
Cinema
Position
SPECIAL
SPECIAL
SCREEN
Move
SCREEN
NR
PIP/DW
PIP/DW
Reset
Black level adj.
PC/DTV Mode
Move
0
Clock
0
Select
D /E
2. Press the G button and then use
D /E
button to select Manual config..
3. Press the G button and then use
D /E
button to to select Phase or Clock.
F /G
Phase
Reset
PC/DTV Mode
Select
G
NR
Black level adj.
1. Press the MENU button and then use
4. Use the
Position
Manual config.
Manual config.
button to select the SCREEN menu.
button to make appropriate adjustments.
• The Phase adjustment range is 0 ~ 31.
• The Clock adjustment range is -127 ~ +128.
5. Press the ENTER button to save the new settings.
Initializing (Reset to original factory value)
- This function operates in every mode.
- To initialize the adjusted value.
PICTURE
PICTURE
Auto config.
SOUND
ARC
SOUND
ARC
TIMER
Cinema
TIMER
Cinema
SPECIAL
SCREEN
PIP/DW
Move
Auto config.
Position
SPECIAL
Position
Manual config.
Manual config.
SCREEN
NR
PIP/DW
Reset
NR
Reset
Black level adj.
Black level adj.
PC/DTV Mode
PC/DTV Mode
Select
Move
1. Press the MENU button and then use
D /E
2. Press the G button and then use
button to select Reset.
D /E
G
To Set
Select
button to select the SCREEN menu.
3. Press the G button.
• You can initialize Manual config., Position, Split zoom, PIP size, PIP position, PIP transparency and sub picture size for DW.
30 Plasma Monitor
Operation
ENGLISH
Black level adj.
- Adjusting the contrast and the brightness of the screen using the black level of the screen.
- This feature operates only in Video1-2-3-4 or Component 576i mode.
PICTURE
Auto config.
PICTURE
Auto config.
SOUND
ARC
SOUND
ARC
TIMER
Cinema
TIMER
Cinema
Position
SPECIAL
SPECIAL
SCREEN
SCREEN
NR
PIP/DW
PIP/DW
Reset
NR
Reset
G
Black level adj.
Black level adj.
Move
Position
Manual config.
Manual config.
Move
Select
1. Press the MENU button and then use
D /E
2. Press the G button and then use
button to select Black level adj.
D /E
Low
High
Select
button to select the SCREEN menu.
3. Press the G button and then use D / E button to select Low or High.
• Low - The reflection of the screen gets darker.
• High - The reflection of the screen gets brighter.
4. Press the ENTER button to save the new settings.
PC/DTV Mode
- To see a normal picture, match the resolution of RGB mode (480p/640x480, 1080p/1920x1080) or HDMI1/DVI mode
(1080p/1920x1080) in the SCREEN menu.
- It can be selected the DTV/PC mode by user.
PICTURE
Auto config.
PICTURE
Auto config.
SOUND
ARC
SOUND
ARC
TIMER
Cinema
TIMER
Cinema
SPECIAL
Position
SPECIAL
SCREEN
PIP/DW
Move
Position
Manual config.
Manual config.
SCREEN
NR
PIP/DW
Reset
NR
Reset
Black level adj.
Black level adj.
PC/DTV Mode
PC/DTV Mode
Select
Move
1. Press the MENU button and then use
D /E
2. Press the G button and then use
button to select PC/DTV Mode.
D /E
G
DTV
PC
Select
button to select the SCREEN menu.
3. Press the ENTER button to save the new settings.
Owner’s Manual 31
Operation
Screen Menu Options continued
Screen Adjustments (Video1-2
(Video1-2 and Component 480i mode only)
- Use this function to correct jittering or picture instability while viewing a video tape.
PICTURE
PICTURE
Screen adj.
SOUND
ARC
SOUND
ARC
TIMER
Cinema
TIMER
Cinema
SPECIAL
NR
Screen adj.
VCR
Reset
SCREEN
Black level adj.
Black level adj.
PIP/DW
PIP/DW
Move
TV
NR
SPECIAL
Reset
SCREEN
G
Move
Select
1. Press the MENU button and then use
D /E
Select
button to select the SCREEN menu.
2. Press the G button and then use
D /E
button to select Screen adj..
3. Press the G button and then use
D /E
button to select TV or VCR.
• Select the VCR option if watching a VCR.
• Select the TV option for other equipment. (Except VCR)
4. Press the ENTER button to save the new settings.
NR (Noise Reduction)
- You can select NR to reduce the picture noise which may appear on the screen during watching the TV.
- This function is not available for use in RGB(PC), HDMI(PC) mode.
PICTURE
PICTURE
Screen adj.
SOUND
ARC
SOUND
ARC
TIMER
Cinema
TIMER
Cinema
SPECIAL
Screen adj.
NR
NR
SPECIAL
Reset
Reset
SCREEN
SCREEN
Black level adj.
PIP/DW
Move
PIP/DW
Select
Move
1. Press the MENU button and then use
2. Press the
G
Black level adj.
button and then use
3. Press the G button and then use
D /E
D /E
D /E
button to select the SCREEN menu.
button to select NR.
button to select On or Off.
4. Press the ENTER button to save the new settings.
32 Plasma Monitor
Select
G
On
Off
Operation
- PIP lets you view 2 different inputs (sources) on your monitor screen at the same time. One source will be large, and the
other source will show a smaller inset image.
- If input signals(50Hz/60Hz) of the main and sub pictures are different in PIP/DW mode, the screens are unnatural.
PIP Size
Watching PIP
Press the WIN.SIZE button and then use
change the sub picture size.
Press the PIP button repeatedly to turn PIP on or off.
PIP Transparency (PIP Mode only)
1. Press the MENU button and then use
select the PIP/DW menu.
D /E
2. Press the G button and then use D
Transparency .
button to select PIP
3. Press the G button and then use F
PIP transparency.
4. Use the
F /G
/G
button to
Moving the PIP
- To make the PIP clear or opaque.
/E
F / G
button to
Press the WIN.POSITION button.
Press the D / E / F / G button repeatedly until desired position is achieved. The sub picture moves up/down/left/right.
button to adjust
button to make appropriate adjustments.
• The adjustment range of PIP Transparency is 0 ~ 16.
5. Press the ENTER button to save.
Selecting an Input Signal Source for the PIP
Use the PIP INPUT button to select the input source for the sub picture.
Main Picture Source
Available Sub Picture Sources
Video1-2-3-4
Component 480i/576i
Component 480p/576p/720p/1080i/1080p
RGB-DTV(480p/576p/720p/1080i/1080p)
RGB-PC
Video1-2-3-4, Component 480i/576i/480p/576p/720p/1080i/1080p,
RGB-DTV(480p/576p/720p/1080i/1080p), RGB-PC, HDMI1/DVI,
HDMI2
HDMI1/DVI, HDMI2
Video1-2-3-4,Component 480i/576i/480p/576p/720p/1080i/1080p,
RGB-DTV(480p/576p/720p/1080i/1080p), RGB-PC
Owner’s Manual 33
ENGLISH
PIP (Picture-In-Picture) Feature
Operation
DW Setup Options
- As the name suggests, this mode splits the screen into 2, allowing 2 picture sources to be shown on the monitor screen at the
same time. Each source is given half the screen.
Watching DW
Press the DW button repeatedly to select one of the DW options.
DW1
DW2
Off
Sub Picture Size Adjustment
Press the WIN.SIZE button.
• Use the F / G button to change the sub picture size.
• Using the WIN.SIZE function in DW mode, main and sub picture sizes are changed
simultaneously.
Using the WIN.SIZE function in PIP mode, sub picture size is changed.
• WIN.POSITION is not functional in DW mode.
Swapping the DW
Use the SWAP button to switch the main and sub pictures in DW mode.
Main Picture
Sub Picture
Selecting a Source for the DW
Use the PIP INPUT button to select the input source for the sub picture.
Main Picture Source
Available Sub Picture Sources
Video1-2-3-4
Component 480i/576i
Component 480p/576p/720p/1080i/1080p
RGB-DTV(480p/576p/720p/1080i/1080p)
RGB-PC
Video1-2-3-4, Component 480i/576i/480p/576p/720p/1080i/1080p,
RGB-DTV(480p/576p/720p/1080i/1080p), RGB-PC, HDMI1/DVI,
HDMI2
HDMI1/DVI, HDMI2
Video1-2-3-4,Component 480i/576i/480p/576p/720p/1080i/1080p,
RGB-DTV(480p/576p/720p/1080i/1080p), RGB-PC
34 Plasma Monitor
External Control Device Setup
(
VIDEO
)
AUDIO
VIDEO IN
S-VIDEO
ENGLISH
External Control Device Setup
AUDIO
VIDEO
COMPONENT IN
- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system)
and control the Monitor’s functions externally.
- Connect the serial port of the control device to the RS-232C jack on the Monitor back panel.
- RS-232C connection cables are not supplied with the Monitor.
VIDEO IN 3
RGB IN
HDMI IN
2
RS-232C IN
(CONTROL & SERVICE)
SERVICE)
VIDEO IN 4
REMOTE
CONTROL IN
AUDIO (RGB/DVI)
1(DVI)
RGB(PC/DTV)
Type of Connector: D-Sub 9-pin Male
No.
1
2
3
4
5
6
7
8
9
1
Pin Name
No Connection
RXD (Receive data)
TXD (Transmit data)
DTR (DTE side ready)
GND
DSR (DCE side ready)
RTS (Ready to send)
CTS (Clear to send)
No Connection
5
9
6
RS-232C Configurations
3- Wire Configuration
(Not standard)
7-Wire Configuration
(Standard RS-232C cable)
PC
RXD
TXD
GND
DTR
DSR
RTS
CTS
Plasma Monitor
2
3
5
4
6
7
8
3
2
5
6
4
8
7
D-Sub 9
D-Sub 9
TXD
RXD
GND
DSR
DTR
CTS
RTS
RXD
TXD
GND
DTR
DSR
RTS
CTS
PC
Plasma Monitor
2
3
5
4
6
7
8
3
2
5
4
6
7
8
D-Sub 9
D-Sub 9
TXD
RXD
GND
DTR
DSR
RTS
CTS
Owner’s Manual 35
External Control Device Setup
Set ID
- Use this function to specify a monitor ID number.
- Refer to ‘Real Data Mapping 1’. See page 38.
PICTURE
Language
PICTURE
Language
SOUND
Key lock
SOUND
Key lock
TIMER
ISM Method
TIMER
ISM Method
SPECIAL
Low power
SCREEN
SPECIAL
SCREEN
Index
PIP/DW
Move
Low power
Set ID
Set ID
G
1
Index
PIP/DW
Select
Move
1. Press the MENU button and then use the
2. Press the
G
button and then use
D /E
3. Press the
G
button and then use
F /G
D /E
Select
button to select the SPECIAL menu.
button to select Set ID.
button to adjust Set ID to choose the desired monitor ID number.
• The adjustment range of Set ID is 1 ~ 99.
Communication Parameters
• Baud rate : 9600 bps (UART)
• Data length : 8 bits
• Parity : None
• Stop bit : 1 bit
• Communication code : ASCII code
Transmission / Receiving Protocol
Command Reference List
Transmission
COMMAND 1 COMMAND 2
DATA
(Hexadecimal)
01. Power
02. Input Select
03. Aspect Ratio
04. Screen Mute
05. Volume Mute
06. Volume Control
07. Contrast
08. Brightness
09. Color
10. Tint
11. Sharpness
12. OSD Select
13. Remote Control Lock Mode
14. PIP/DW
15. PIP Position
16. Treble
17. Bass
18. Balance
19. Color Temperature
20. Red adjustment
21. Green adjustment
22. Blue adjustment
23. PIP Input Select
24. Abnormal State
25. ISM Method
26. Low Power
27. Picture Size Setting
for DW mode
28. Auto Configure
29. Key
36 Plasma Monitor
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
j
j
j
a
b
c
d
e
f
g
h
i
j
k
l
m
n
q
r
s
t
u
v
w
$
y
z
p
q
t
0~1
1~9
0~3
0~1
0~1
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0~1
0~1
0~3
0~3
0 ~ 64
0 ~ 64
0 ~ 64
0~3
0 ~ 14
0 ~ 14
0 ~ 14
1~9
0~a
0~3
0~1
0 ~oa
j
m
u
c
1
Key code
[Command1][Command2][ ][Set ID][ ][Data][Cr]
* [Command 1]: k, j, m
* [Command 2]: To control Plasma Monitor set.
* [Set ID]: You can adjust the set ID to choose desired monitor ID number in Special menu. Adjustment range
is 1 ~ 99. When selecting Set ID ‘0’, every connected Plasma Monitor set is controlled. Set ID is
indicated as decimal (1~99) on menu and as
Hexa decimal (0x0~0x63) on transmission/receiving protocol.
* [DATA]: To transmit command data.
Transmit ‘FF’ data to read status of command.
* [Cr]: Carriage Return
ASCII code ‘0x0D’
* [ ]: ASCII code ‘space (0x20)’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The Monitor transmits ACK (acknowledgement) based on
this format when receiving normal data. At this time, if the
data is data read mode, it indicates present status data. If
the data is data write mode, it returns the data of the PC
computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][x]
* The Monitor transmits ACK (acknowledgement) based on
this format when receiving abnormal data from
non-viable functions or communication errors.
Data 1: Illegal Code
2: Not supported function
External Control Device Setup
04. Screen Mute (Command 2:d)
G To control Power On/Off of the Monitor.
G To select screen mute on/off.
Transmission
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
Data 0 : Power Off
ENGLISH
01. Power (Command 2:a)
[k][d][ ][Set ID][ ][Data][Cr]
1 : Power On
Acknowledgement
Data 0 : Screen mute off (Picture on)
1 : Screen mute on (Picture off)
[a][ ][Set ID][ ][OK][Data][x]
Acknowledgement
[d][ ][Set ID][ ][OK][Data][x]
G To show Power On/Off.
Data 0 : Screen mute off (Picture on)
1 : Screen mute on (Picture off)
Transmission
[k][a][ ][Set ID][ ][FF][Cr]
Data 0 : Power Off
1 : Power On
Acknowledgement
[a][ ][Set ID][ ][OK][Data][x]
* In a like manner, if other functions transmit ‘FF’ data
based on this format, Acknowledgement data feedback
presents status about each function.
02. Input Select (Command 2:b) (Main Picture Input)
05. Volume Mute (Command 2:e)
G To select input source for the Monitor.
You can also select an input source using the INPUT
button on the Monitor's remote control.
G To control volume mute on/off.
You can also adjust mute using the MUTE button on
remote control.
Transmission
Transmission
[k][e][ ][Set ID][ ][Data][Cr]
[k][b][ ][Set ID][ ][Data][Cr]
Data 1
2
3
4
5
:
:
:
:
:
Video1
Video2
Component1
Component2
RGB
6
7
8
9
:
:
:
:
HDMI1/DVI
Video3
Video4
HDMI2
Data 0 : Volume mute on (Volume off)
1 : Volume mute off (Volume on)
Acknowledgement
[e][ ][Set ID][ ][OK][Data][x]
Data 0 : Volume mute on (Volume off)
1 : Volume mute off (Volume on)
Acknowledgement
[b][ ][Set ID][ ][OK][Data][x]
Data 1
2
3
4
5
:
:
:
:
:
Video1
Video2
Component1
Component2
RGB
6
7
8
9
:
:
:
:
HDMI1/DVI
Video3
Video4
HDMI2
03. Aspect Ratio (Command 2:c) (Main picture format)
G To adjust the screen format.
You can also adjust the screen format using the ARC
(Aspect Ratio Control) button on remote control or in the
Screen menu.
Transmission
[k][c][ ][Set ID][ ][Data][Cr]
Data 0
1
2
3
:
:
:
:
Normal screen (4:3)
Wide screen (16:9)
Wide screen (Horizon)
Full screen (Zoom)
Acknowledgement
06. Volume Control (Command 2:f)
G To adjust volume.
You can also adjust volume with the volume buttons
on remote control.
Transmission
[k][f][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
• Refer to ‘Real data mapping1’. See page 38.
Acknowledgement
[f][ ][Set ID][ ][OK][Data][x]
Data Min : 0 ~ Max : 64
[c][ ][Set ID][ ][OK][Data][x]
Owner’s Manual 37
External Control Device Setup
07. Contrast (Command 2:g)
10. Tint (Command2:j)
G To adjust screen contrast.
You can also adjust contrast in the picture menu.
G To adjust the screen tint.
You can also adjust tint in the Picture menu.
Transmission
Transmission
[k][g][ ][Set ID][ ][Data][Cr]
[k][j][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
• Refer to ‘Real data mapping1’ as shown below.
Data Red : 0 ~ Green : 64
• Refer to ‘Real data mapping 1’.
Acknowledgement
Acknowledgement
[g][ ][Set ID][ ][OK][Data][x]
[j][ ][Set ID][ ][OK][Data][x]
Data Min : 0 ~ Max : 64
Data Red : 0 ~ Green : 64
* Real data mapping 1
0 : Step 0
11. Sharpness (Command2:k)
A : Step 10 (SET ID 10)
G To adjust the screen sharpness.
You can also adjust sharpness in the Picture menu.
F : Step 15 (SET ID 15)
10 : Step 16 (SET ID 16)
Transmission
63 : Step 99 (SET ID 99)
64 : Step 100
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping 1’.
Acknowledgement
[k][k][ ][Set ID][ ][Data][Cr]
[k][ ][Set ID][ ][OK][Data][x]
08. Brightness (Command2:h)
Data Min : 0 ~ Max : 64
G To adjust screen brightness.
You can also adjust brightness in the Picture menu.
Transmission
12. OSD Select (Command2:l)
[k][h][ ][Set ID][ ][Data][Cr]
G To select OSD (On Screen Display) on/off.
Data Min : 0 ~ Max : 64
• Refer to ‘Real data mapping 1’.
Transmission
Acknowledgement
Data 0: OSD off
[h][ ][Set ID][ ][OK][Data][x]
Data Min : 0 ~ Max : 64
[k][l][ ][Set ID][ ][Data][Cr]
1: OSD on
Acknowledgement
[l][ ][Set ID][ ][OK][Data][x]
Data 0: OSD off
1: OSD on
09. Color (Command2:i)
13. Remote Control Lock Mode (Command2:m)
G To adjust the screen color.
You can also adjust color in the Picture menu.
G To lock the remote control and front panel controls on the
monitor
Transmission
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
[k][m][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
• Refer to ‘Real data mapping 1’.
Acknowledgement
Data 0: lock off
1: lock on
Acknowledgement
[m][ ][Set ID][ ][OK][Data][x]
[i][ ][Set ID][ ][OK][Data][x]
Data Min : 0 ~ Max : 64
Data 0: lock off
1: lock on
• If you’re not using the remote control and front panel controls on the monitor, use this mode. When main power is
on/off, remote control lock is released.
38 Plasma Monitor
External Control Device Setup
18. Balance (Command2:t)
G To control the PIP (Picture-in-Picture) or DW.
You can also control the PIP/DW using the PIP or DW button
on the remote control or in the PIP/DW menu.
G To adjust balance.
You can also adjust balance in the Sound menu.
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
[k][n][ ][Set ID][ ][Data][Cr]
Data 0: PIP/DW off
1: PIP
2: DW1
3: DW2
Acknowledgement
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping 1’. See page 38.
Acknowledgement
[t][ ][Set ID][ ][OK][Data][x]
[n][ ][Set ID][ ][OK][Data][x]
Data 0: PIP/DW off
1: PIP
Transmission
2: DW1
3: DW2
15. PIP Position (Command2:q)
G To select sub picture position for PIP.
You can also adjust the sub picture position using
Win.position on the remote control or in the PIP/DW menu.
Data Min: 0 ~ Max: 64
19. Color Temperature (Command2:u)
G To adjust color temperature.
You can also adjust ACC in the Picture menu.
Transmission
Transmission
[k][u][ ][Set ID][ ][Data][Cr]
[k][q][ ][Set ID][ ][Data][Cr]
Data 0: Cool
Data 0:
1:
2:
3:
Acknowledgement
Right down on screen
Left down on screen
Left up on screen
Right up on screen
Acknowledgement
[q][ ][Set ID][ ][OK][Data][x]
Data 0:
1:
2:
3:
Right down on screen
Left down on screen
Left up on screen
Right up on screen
16. Treble (Command2:r)
G To adjust treble.
You can also adjust treble in the Sound menu.
1: Normal
2: Warm
3: Off
2: Warm
3: Off
[u][ ][Set ID][ ][OK][Data][x]
Data 0: Cool
1: Normal
20. Red adjustment (Command2:v)
G To adjust red in color temperature
Transmission
[k][v][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 14
• Refer to ‘Real data mapping 2’. See page 40.
Acknowledgement
[v][ ][Set ID][ ][OK][Data][x]
Transmission
[k][r][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping 1’. See page 38.
Acknowledgement
[r][ ][Set ID][ ][OK][Data][x]
Data Min: 0 ~ Max: 64
17. Bass (Command2:s)
21. Green adjustment (Command2:w)
G To adjust green in color temperature
Transmission
[k][w][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 14
• Refer to ‘Real data mapping 2’. See page 40.
Acknowledgement
[w][ ][Set ID][ ][OK][Data][x]
G To adjust bass.
You can also adjust bass in the Sound menu.
22. Blue adjustment (Command2:$)
Transmission
G To adjust blue in color temperature
[k][s][ ][Set ID][ ][Data][Cr]
Transmission
[k][w][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
• Refer to ‘Real data mapping 1’. See page 38.
Acknowledgement
Data Min: 0 ~ Max: 14
• Refer to ‘Real data mapping 2’. See page 40.
[s][ ][Set ID][ ][OK][Data][x]
Acknowledgement
Data Min: 0 ~ Max: 64
[$][ ][Set ID][ ][OK][Data][x]
Owner’s Manual 39
ENGLISH
14. PIP / DW (Command2:n)
External Control Device Setup
* Real data mapping 2
26. Low Power (Command2:q)
0 : -10
1 :-9
2 :-8
G To control the low power function on/off.
A : 0
Data 0: Low power off
1: Low power on
Acknowledgement
Transmission
[j][q][ ][Set ID][ ][Data][Cr]
12 : + 8
13 : + 9
14 : + 10
[q][ ][Set ID][ ][OK][Data][x]
Data 0: Low power off
1: Low power on
23. PIP Input Select (Command2:y)
G To select input source for sub picture in PIP mode.
Transmission
27. Picture Size Setting for DW mode
(Command2:t)
[k][y][ ][Set ID][ ][Data][Cr]
Data 1
2
3
4
5
:
:
:
:
:
Video1
Video2
Component1
Component2
RGB
6
7
8
9
:
:
:
:
HDMI1/DVI
Video3
Video4
HDMI2
[y][ ][Set ID][ ][OK][Data][x]
:
:
:
:
:
Transmission
[j][t][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 0a
• Refer to ‘Real data mapping1’. See page 38.
Acknowledgement
Acknowledgement
Data 1
2
3
4
5
G To adjust main picture size in DW mode.
6
7
8
9
Video1
Video2
Component1
Component2
RGB
:
:
:
:
HDMI1/DVI
Video3
Video4
HDMI2
24. Abnormal State (Command2:z)
[t][ ][Set ID][ ][OK][Data][x]
Data Min: 0 ~ Max: 0a
28. Auto Configure (Command2:u)
Transmission
G To adjust picture position and minimize image shaking
automatically. Auto Configure only works in RGB-PC
mode.
[k][z][ ][Set ID][ ][FF][Cr]
Transmission
Data FF:Read
Acknowledgement
[j][u][ ][Set ID][ ][Data][Cr]
G To recognize an abnormal state.
Data 1
[z][ ][Set ID][ ][OK][Data][x]
Data 0:
1:
2:
3:
4:
5:
Power on(signal)
Power on(No signal)
Remote control off
Sleep time off
RS-232C off
5V monitor off
6: AC detect off
7: Fan Alarm off
8: Off timer off
9: No signal off
a: Connection Detect off
* If you do not press any button within 2 hours after the monitor turns
on with the On Timer function, the monitor will automatically revert to
standby mode.
25. ISM Method (Command2:p)
• Refer to ‘Real data mapping1’. See page 38.
Acknowledgement
[u][ ][Set ID][ ][OK][Data][x]
Data 1
29. Key (Command2:c)
G To adjust Key code for IR remote control.
Transmission
G To avoid having a fixed image remain on screen.
[m][c][ ][Set ID][ ][Data][Cr]
Transmission
[j][p][ ][Set ID][ ][Data][Cr]
Data 0: Normal
1: White wash
Data Key code : Refer to See page 42.
2: Orbiter
3: Inversion
Acknowledgement
[c][ ][Set ID][ ][OK][Data][x]
[p][ ][Set ID][ ][OK][Data][x]
Data 0: Normal
1: White wash
40 Plasma Monitor
Acknowledgement
2: Orbiter
3: Inversion
IR Code
ENGLISH
IR Code
How to Connect
G Connect your wired remote control to the Remote Control port on the Monitor.
Remote Control IR Code
G Output waveform
Single pulse, modulated with 37.917KHz signal at 455KHz
TC
Carrier frequency
FCAR = 1/TC = fOSC/12
Duty ratio = T1/TC = 1/3
T1
G Configuration of frame
• 1st frame
Lead
code
Low
custom code
High
custom code
Data code
Data code
C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7
• Repeat frame
Repeat code
Tf
G Lead code
9 ms
4.5 ms
0.55 ms
G Repeat code
9 ms
2.25 ms
G Bit description
• Bit “0”
• Bit “1”
0.56 ms
0.56 ms
1.12 ms
2.24 ms
G Frame interval : Tf
The waveform is transmitted as long as a key is depressed.
Tf
Tf
Tf=108ms @455KHz
Owner’s Manual 41
IR Code
Code (Hexa)
10
11
12
13
14
15
16
17
18
19
0E
09
08
02
03
00
01
4D
52
44
0B
43
79
62
64
07
06
40
41
5B
60
92
61
6B
CD
CE
3E
75
99
5A
D0
BF
D4
D5
C6
42 Plasma Monitor
Function
Number Key 0
Number Key 1
Number Key 2
Number Key 3
Number Key 4
Number Key 5
Number Key 6
Number Key 7
Number Key 8
Number Key 9
SLEEP
MUTE
POWER
VOL+
VOLCH+
CHAPC
DASP
ENTER (Á)
AII INPUT SELECT
MENU
ARC
Window Position
Window Size
F
G
D
E
EXIT
PIP
XD
PIP Input
DW
Video
HDMI2
Key lock
Index
Auto config.
Input video1
Input video2
Input Component 1
Input Component 2
Input RGB
Input HDMI1/DVI
Note
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button (Power On/Off)
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button (4:3/16:9/Horizon/Zoom mode Selection)
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
Discrete IR Code (Only RGB mode)
Discrete IR Code (Input Video 1 Selection)
Discrete IR Code (Input Video 2 Selection)
Discrete IR Code (Input Component 1 Selection)
Discrete IR Code (Input Component 2 Selection)
Discrete IR Code (Input RGB Selection)
Discrete IR Code (Input HDMI1/DVI Selection)
Programming the Remote
G The remote control is a multi-brand or universal remote control. It can be programmed to operate most remote-controllable
devices of other manufacturers.
Note that the remote control may not control all models of other brands.
Programming a code into a remote mode
1. Test your remote control.
To find out whether your remote control can operate the component without programming, turn on the component such as a VCR
and press the corresponding MODE button (VCR) on the remote control, while pointing at the component.
2. Turn on the component to be programmed, then press the corresponding MODE button on the remote control.
3. Press the MENU and MUTE buttons simultaneously, the remote control is ready to be programmed for the code.
4. Enter a code number using the number buttons on the remote. Programming code numbers for the corresponding component can
be found on the following pages. Again, if the code is correct, the device will turn off.
5. Press the MENU button to store the code.
6. Test the remote control functions to see if the component responds properly. If not, repeat from step 1.
Owner’s Manual 43
ENGLISH
Programming the Remote
Programming the Remote
Programming Codes
VCRs
Brand
Codes
Brand
Codes
Brand
Codes
Brand
Codes
AIWA
AKAI
034
016
125
072
031
012
035
028
108
003
031
005
065
112
108
012
034
059
006
029
036
129
003
034
031
107
132
012
004
043
031
031
012
040
043
012
048
130
KENWOOD
014
047
001
101
034
003
017
040
031
067
012
069
101
027
031
003
033
101
045
013
013
049
151
034
024
012
048
043
053
066
133
013
063
031
031
067
101
013
PORTLAND
PULSAR
QUARTZ
QUASAR
RCA
108
072
011
033
013
040
107
145
003
031
053
058
148
014
032
105
113
125
022
003
102
017
131
003
013
031
101
031
024
003
056
077
034
013
031
067
034
010
TATUNG
TEAC
TECHNICS
TEKNIKA
039
034
031
019
101
034
006
008
059
040
040
012
048
012
040
003
031
053
012
034
058
AMPRO
ANAM
AUDIO DYNAMICS
BROKSONIC
CANON
CAPEHART
CRAIG
CURTIS MATHES
DAEWOO
DAYTRON
DBX
DYNATECH
ELECTROHOME
EMERSON
FISHER
FUNAI
GE
GO VIDEO
HARMAN KARDON
HITACHI
INSTANTREPLAY
JCL
JCPENNY
JENSEN
JVC
043 046 124
146
033
023
037
031
040
033
007
108
116
103
039 043
129
033
135
041
010 064
110 111
117 119
023 039 043
053
027
035
101
153
010
LG (GOLDSTAR)
LLOYD
LXI
MAGIN
MAGNAVOX
MARANTZ
MARTA
MATSUI
MEI
MEMOREX
017
031
037
131
008
025
034
046
138
009
033
109
136
045
018
063
033
033
013
066
063 072
144 147
MTC
MULTITECH
NEC
026 034
137 150
NORDMENDE
OPTONICA
PANASONIC
MGA
MINOLTA
MITSUBISHI
PENTAX
015 033
101
031 033 043
050 055 060
150 152
PHILCO
PHILIPS
PILOT
PIONEER
034 039 043
048
012 013 020
106 114 123
009 013 014
034 101 106
033 034 041
068
031 033 067
030
033
010
034
102
046
020
020
051
REALISTIC
RICO
RUNCO
SALORA
SAMSUNG
014 031
053 072
134 139
059
045 046
059 061
040
034
023 039 043
054
070 074 083
140 145
020 031 033
034 067
033 034 054
071 101
021 048
SANSUI
SANYO
SCOTT
SEARS
SHARP
SHINTOM
SONY
SOUNDESIGN
STS
SYLVANIA
SYMPHONIC
TANDY
014
066
020
041
109
147
008
033
054
075
033
062
140
145
034
063
144
010 014
034 040
101
THOMAS
TMK
TOSHIBA
TOTEVISION
UNITECH
VECTOR RESEARCH
040 102 104
107 109 112
115 120 122
043 048 135
007 010 014
134
037 112 129
VICTOR
VIDEO CONCEPTS
VIDEOSONIC
WARDS
YAMAHA
ZENITH
043
039 043
033 070
031 033 034
013 042 047
082 112 131
101
034 046
013
033
054
034
048
072
017
034
131
039
056
080
024
040
043
101
008 009 010
014 017 020
042 073 081
054 149
009 031 052
057 058 076
078 149
033 034 059
034
CATV
CATV
Brand
Codes
Brand
Codes
ABC
003
046
112
014
005
026
092
007
007
065
080
019
023
020
057
032
072
008
052
GOLDEN CHANNEL
HAMLIN
HITACHI
HOSPITALITY
JERROLD
030
049
052
070
002
009
074
001
037
033
010
100
028
015
073
016
044
100
006
AJIN
ANTRONIK
ARCHER
CABLE STAR
CENTURION
CENTURY
CITIZEN
COLOUR VOICE
COMBANO
COMTRONICS
DIAMOND
EAGLE
EASTERN
ELECTRICORD
GE
GEMINI
GI
004 039 042
052 053
007 014 024
090
081
030
030 040
062 066
022 025 054
074
44 Plasma Monitor
LG (GOLDSTAR)
M-NET
MACOM
MAGNAVOX
MEMOREX
MOVIE TIME
NSC
OAK
PANASONIC
PARAGON
PHILIPS
050 055
055
077
003 004 008
010 052 069
106 101 005
012 064 079
032
028 038 071
Brand
PIONEER
POST NEWS WEEK
PRUCER
PTS
PULSAR
RCA
REGAL
REGENCY
REMBRANT
RK
SAMSUNG
SCIENTIFIC ATLANTA
031 037 053
047
012 013 020
SHERITECH
SIGNAL
SIGNATURE
Codes
Brand
Codes
065
034
076
016
059
011
073
100
047
049
057
025
091
102
003
043
022
030
052
SL MARX
SPRUCER
STARCOM
STARGATE
SYLVANIA
TADIRAN
TAEKWANG
TAIHAN
TANDY
TEXSCAN
TOCOM
TOSHIBA
UNIKA
UNITED CABLE
UNIVERSAL
030
047
002
008
067
030
110
105
017
029
039
100
007
004
005
026
012
087
100
085 090
051 052 063
048 071 072
074
050
107 030 068
011 041 042
045 046
VIEWSTAR
ZENITH
078
004 008 009
030
067
040 056
014
053
007
027
015
088
114
024
014
032
018
089
060
024
035
086
093
Programming the Remote
ENGLISH
HDSTB
Brand
Codes
Brand
ALPHASTAR DSR
AMPLICA
BIRDVIEW
BSR
CAPETRONICS
CHANNEL MASTER
123
050
051
053
053
013
036
008
054
050
005
011
141
024
038
093
097
122
089
EUROPLUS
FUJITSU
CHAPARRAL
CITOH
CURTIS MATHES
DRAKE
DX ANTENNA
ECHOSTAR
ELECTRO HOME
126 129
014 015 018
055
009 012 077
145
006 007 010
052 112 116
046
040
094
098
056
057
095
099
076
058
096
100
Codes
114
017
133
GENERAL INSTRUMENT 003
031
HITACHI
139
HOUSTON TRACKER
033
057
HUGHES
068
HYTEK
053
JANIEL
060
JERROLD
061
KATHREIN
108
LEGEND
057
LG
001
LUTRON
132
LUXOR
062
MACOM
010
065
021
134
004
059
140
037
104
Brand
022 027
016 029
101
039 051
147
144
059 063 064
Codes
MEMOREX
NEXTWAVE
NORSAT
057
028
069
PACE SKY SATELLITE 143
PANASONIC
060
PANSAT
121
PERSONAL CABLE 117
PHILIPS
071
PICO
105
PRESIDENT
019
PRIMESTAR
030
PROSAT
072
RCA
066
REALISTIC
043
SAMSUNG
123
SATELLITE SERVICE CO 028
085
SCIENTIFIC ATLANTA
032
SONY
103
124 125
070
Brand
Codes
STARCAST
SUPER GUIDE
TEECOM
041
020
023
088
137
002
016
044
078
101
115
128
081
091
142
TOSHIBA
UNIDEN
102
110 111
VIEWSTAR
WINEGARD
ZENITH
106
074
124 125
026 075 087
090 107 130
127
025
045
079
135
042 043
048 049
080 086
136
146
082 083 084
120
035 047 057
138
Audio
Brand
AIWA
Codes
014
125
230
AKAI
163
ANAM
003
059
217
BURMECTER
252
CARVER
086
CLARION
199
DAEWOO
027
102
DENON
015
FANTASIA
071
FINEARTS
022
FISHER
089
LG(GOLDSTAR)
001
087
190
211
HAITAI
034
HARMAN/KARDON 068
INKEL
037
078
122
152
157
189
225
247
028 070 096
129 139 229
014 017 023
106 189 216
235 236
Brand
Codes
JVC
KEC
KENWOOD
004
185
038
170
215
030
045
014
100
175
179
201
214
238
103
111
002
034
097
049
104
107
046
013
048
133
158
007
142
104
KOHEL
NAD
LOTTE
053 060 184
148 198 221
075 130 143
099
021
107
191
212
035
058
079
149
153
158
207
226
024
108
192
239
188
062
095
150
154
159
222
227
029
110
210
222
069
121
151
155
160
224
243
LXI
MAGNAVOX
MARANTZ
MCINTOSH
MCS
MEMOREX
NAD
ONKYO
OPTIMUS
PANASONIC
PENNEY
013
186
050
171
222
046
016
172
176
180
202
219
240
141
187
067 089
197 206
036
173
177
181
208
223
098
174
178
183
213
232
018 020 025
041 081 090
112
Brand
Codes
PHILIPS
PIONEER
026
039
065
115
113
080
092
103
124
193
204
011
019
106
031
072
156
206
005
044
118
012
076
162
166
205
254
010
185
101
QUASAR
RCA
RCX
REALISTIC
SAMSUNG
SANSUI
SANYO
SCOTT
SHARP
SHERWOOD
SONY
TAEKWANG
040 041 047
056 057 132
140
033 064 113
220 241 251
TEAC
TECHNICS
112
042
091
123
106
145
194
244
135
083
186
032
082
184
209
006
045
126
020
077
163
167
231
143
043
093
127
253
063
094
250
146
195
245
138
234
182
203
246
144
Brand
Codes
TOSHIBA
THE
VICTOR
WARDS
YAMAHA
147 218
137
061
088 131
089
054 055 066 092
199
051
117 119
199 200
158
109
248
073
105
164
168
233
114
249
074
161
165
169
242
085 106 136
187 237
113 128 134
DVD
Brand
Codes
Brand
Codes
Brand
Codes
Brand
Codes
APEX DIGITAL
DENON
GE
HARMAN KARDON
JVC
LG
022
020 014
005 006
027
012
001 010 016 025
MAGNAVOX
MARANTZ
MITSUBISHI
NAD
ONKYO
PANASONIC
013
024
002
023
008 017
003 009
PHILIPS
PIONEER
PROCEED
PROSCAN
RCA
SAMSUNG
013
004
021
005
005
011
SONY
THOMPSON
TOSHIBA
YAMAHA
ZENITH
007
005
019
009
010
026
006
006
015
006
008
018
016 025
Owner’s Manual 45
Troubleshooting Checklist
Troubleshooting Checklist
• Check whether the Monitor is turned on.
No picture &
No sound
• Power cord inserted into wall outlet?
• Test the wall power outlet, plug other product’s power cord into the wall outlet
where the Monitor’s power cord was plugged in.
Picture OK &
No sound
• Press the VOLUME (+) button.
• Sound muted? Press MUTE button.
• Check to see if there is any object between the Plasma Display and the
remote control causing obstruction.
The remote control
doesn’t work
• Are batteries installed with correct polarity (+ to +, - to -)?
(Refer to p.11)
• Install new batteries. (Refer to p.11)
Picture appears slowly
after switching on
• This is normal, the image is muted during the plasma display startup process.
Please contact your service center, if the picture has not appeared after five
minutes.
• Select Color in the Picture menu and press the
(Refer to p.21)
No or Poor color
or Poor picture
G
button.
• Keep a sufficient distance between the Monitor and the VCR.
• Activate any function to restore the brightness of the picture.
(If still picture is on the screen for more than 5 minutes, the screen gets dark.)
Horizontal/vertical bars
or picture shaking
• Check for local interference such as an electrical appliance or power tool.
No output from one of
the speakers
• Adjust Balance in the Sound menu. (Refer to p.22)
Unusual sound from
inside the monitor
• A change in ambient humidity or temperature may result in an unusual noise
when the plasma display is turned on or off and does not indicate a fault with
the monitor.
46 Plasma Monitor
Product Specifications
ENGLISH
Product Specifications
71PY1M
71PY1MG
71PY1MC
71PY1MV
(71PY1M-WA)
(71PY1MG-WA)
(71PY1MC-WA)
(71PY1MV-WA)
Width (inches / mm)
68.9 / 1750
68.9 / 1750
68.9 / 1750
68.9 / 1750
Height (inches / mm)
38.7 / 982
38.7 / 982
38.7 / 982
38.7 / 982
Depth (inches / mm)
3.9 / 98
3.9 / 98
3.9 / 98
3.9 / 98
Weight (pounds / kg)
194.9 / 88.4
194.9 / 88.4
194.9 / 88.4
194.9 / 88.4
MODELS
Power requirement
AC100-240V~ 50/60Hz
Resolution
1920 x 1080 (Dot)
Viewing Size (mm)
1512.26
Operating Temperature
Environmental
condition
Operating Humidity
Storage Temperature
Storage Humidity
32 ~ 104°F (0 ~ 40°C)
Less than 80%
-4 ~ 140°F (-20 ~ 60°C)
Less than 85%
• The specifications shown above may change without notice for quality improvement.
Owner’s Manual 47
Download PDF