LG | LSW240B | LG LSW240B Owner’s Manual

OWNER’S MANUAL
Wall Mounting Bracket
Please read this manual carefully before operating
your set and retain it for future reference.
LSW240B
P/NO : MFL63640548 (1312-REV00)
www.lg.com
(Brazil : www.lge.com)
Component
Wall mount anchor 4 units
Wall mount screw 4 units
User manual
Guide spacer 4 units
Guide space screw 4 units
Safety clip 2 units
Safety clip screw 2 units
(M4X12 mm)
Set protection cushion
4 units
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Warning
This wall mount should be installed by a trained and
experienced installer designated by the retailer.
Having the product installed by a non-specialized installer is
very dangerous and can cause damage or injury.
Use a trained and experienced installer to move or
replace the wall mount, if needed.
Installation requires special techniques and moving or installing
the product on your own can cause serious safety issues.
When installing the wall mount, never hang the
power or signal cable on the rear side the TV.
The cord can be damaged and cause a fire, an electric
shock or damage to the product.
2
Do not install the product where the weight cannot be
supported.
If the strength of the location where the wall mount is installed
is not strong enough, it can fall off and cause an injury.
After installing the wall mount, do not hang on the
product or apply severe impact to the product.
The product can fall off and cause injury.
If the product is not installed based on the directions in
the user manual, it can cause a serious injury or damage
to the product.
During the installation, check the type of wall
material and use the sealed anchor and screw if the
conditions comply.
When installing the product or adjusting the height of
the product after installing, always do so with 2 people.
Working alone can cause the product to fall off and result in
injury or damage to the product.
When drilling holes in the wall, always use a drill bit
and drill of designated diameter. Also follow the
designated directions for the depth of the hole.
If you do not use the designated anchor or screw, the
mount may not be able to withstand the weight of
the product and cause a safety issue.
If the product is installed without following the designated
method, the product may be unstable and cause a safety
issue.
Do not wipe the product with a wet towel and do not use any
heater or humidifier below where the product is installed.
Do not install the product near any object that
may cause vibration.
If water flows into the product or if moisture and heat are applied to the
product, it can cause a fire, an electric shock or problem to the product.
Do not install the product near any high voltage power
cable or power source.
Unplug the power cord from the power outlet before
installing the product.
If you install the product with the power cord plugged, it can
cause an electric shock or a fire.
Do not install the product with bare hands. Always
wear proper work gloves.
It can cause an injury.
Do not allow the video connectors connected to the
display to press against the wall. Use the included
right-angle adapters if needed.
Only use attachments/accessories specified by the
manufacturer.
Before installation
* Do not use the product for purposes other than mounting a display on the wall.
* When installing/using the wall mount, be cautious of product damage and avoid accidents.
* If you have not fully read and understood the installation manual, do not install the product and contact
the dealer to have a specialized installer install the product for you.
*E
ven if you are not a specialized installer, it is advantageous to have experience in mechanical or
construction field in completely understanding this manual and installing the product.
* This product is designed to be mounted to walls that use standard intervals between the studs.
* Install the screw to attach the wall mount so that it can be assembled at the center from both ends of
the studs. Use of stud finder, a separate device, is recommended.
* Install the product only on a vertical wall.
The manufacturer is not responsible for issue from installing the product on severely wall or on the
ceiling.
*K
eep the included accessories out of reach of babies or children as it can cause safety issues including
suffocation from swallowing the parts.
* Make sure screws are tight against the wall, but do not overtighten.
* Be careful not to install a TV that exceeds the weight restrictions of the wall mount.
* Be careful with the tools used during installation to prevent accidents or damage.
3
ENGLISH
Install the product according to the directions in
the user manual.
ENGLISH
d
Caution
Installation method
- Tools you will need : Phillips head "+" driver(Manual or motorized) Ø4 mm drill bit for wood or steel / Level / Stud finder / Drill.
You may also need an 8 mm socket wrench or an Ø8 mm drill bit for concrete.
- The actual product may differ from the picture.
1
Attach the mounting bracket to the TV
If the screw will not fully tighten when using a guide spacer, recheck the assembly depth of the screw and
refer to the technical service manual.
<Work procedure>
Guide spacer
2
1. Check to see if the display has screws installed into the
mounting holes. If so, remove those.
2. Assemble the guide spacer and the guide spacer screw in
order as shown in the picture.
- Assemble the guide spacer to the set by tightening the
screws.
- Tighten the screw until the set, guide spacer and the screw
are fully pressing against one another.
- Use a Phillips Head driver (Manual or motorized) when
tightening the screws.
Guide spacer
screw
How to attach to masonry walls
-U
se the anchors for wall material of concrete, light concrete, strong natural stone, soft natural stone masonry brick and
hallow block that do not crack.
Please follow the below direction.
- Check the material and thickness of the wall.
- When installing the product on wall material not designated, install the product so that each fixated location can withstand a
pull out load of 70 kgf (686 N) and shear load of 100 kgf (980 N) or above.
Anchor
Wall mount screw
a
b
c
d
e
- Use the Ø8 mm drill bit for concrete and hammer (Impact) drill. z
a. Use a drill bit Ø8 mm to drill a hole for the anchor location within a depth of 80 mm - 100 mm
b. Clean the drilled hole.
c. Insert the sealed anchor into the hole. (When inserting the anchor, use a hammer.)
d. Set the wall mount on the wall by aligning to the location of the hole. and, set the angle adjusting part to face upward.
e. Align the wall mount bolts to the holes and tighten them by hand. Then, fasten the bolts at a torque of 45 kgf/cm - 60 kgf/cm.
4
ENGLISH
How to install the wall mount
→ If the screw cannot be assembled in the designated location
inevitably, it can be assembled by rearranging to the closest
location. But, do not change 2 or more locations from the
designated spot.
→ Assemble the wall mount screw on 1 left and 1 right location
on the top part and 1 left and 1 right location on the bottom
part.
→ At this time, use a Phillips Head driver (Manual or motorized)
or 8 mm wrench to tighten the screw so that the wall, wall
bracket and screw are completely pressed against one
another.
Wall mount
screw
4
ENGLISH
.
3
How to assemble the wall mount support and display
- Always install the display with 2 or more people.
Safety clip
Safety clip screw
* Assemble the wall mount
support, product and safety
clip.
* Caution : Prevent the power
cord from being pinched
between the wall mounting
bracket and the set when
installing the set.
(A pinched power cord may
cause an electrical short)
1. S
et the display with the guide spacer assembled on the wall mount bracket on the wall in arrow direction. At this time, align
the bottom assembly part and lift the set up lightly to align the top part.
2. When adjusting the location, assemble the provide safety clip as shown in the picture to prevent the product from moving.
Tighten the safety clip screw completely. If the safety clip is not tightened as shown in the picture, the product can fall off.
→ Pull on the bottom of the set to make sure the display is secure.
→W
hen installing a display rotated, only rotate the display 90 degrees (portrait mode). (Only applies for VESA 200X200, 400x400)
→W
hen connecting cables and accessories, make sure that the product is installed at a sufficient distance from the wall to avoid
stress on them.
→ When you push the product with excessive force, the product can be damaged.
5
5
How to level the Display
After installing the display, check to make sure it is level. The wall mount has two
screws that make minor adjustments to the level.
± 5 mm (Leveling)
6
Cable arrangement and set protection cushion
- Arrange the cables as shown in the picture. Use some type of cable banding device to hold all the cables together.
- Attach the set protection cushion to mitigate the impact between the wall and the set when adjusting the angle. Attach the
set protection cushion as shown in the picture.
Avoid crushing the power cord and the cables between the wall mount and the wall.
6
ENGLISH
ENGLISH
Product specification
[ Unit : mm ]
°~
°~
°± °
°± °
MAX.
MIN.
145
172.5
Model Name
LSW240B
Width (mm)
281
Height (mm)
234
Depth (mm)
14
Weight (kg)
1.5
Weight with packing (kg)
2.2
Wall Mount VESA Specification
200X200
Max.UL Load Capacity (kg)
40
41.5
7
The model and serial number of the product is located
on the back or one side of the product. Record it below
should you ever need service.
MODEL
SERIAL
Supported Displays
(Please contract the retailers or refer to the TV owner’s
manual for applicable models.)
Download PDF