LG | MT-42PZ15 | LG MT-42PZ15 Owner’s Manual

Please read this owner's manual
operating
carefully
before
the Monitor.
Retain it for future reference.
Record model number and serial number of the
Monitor.
See the label attached
on
the back of the Monitor
and
quote this information to your dealer when you
require service.
Model number
Serial number
P/NO
:
:
:
PLASMONITR
MT-42PZ15/A/B/G/K/S
OWNER'S MANUAL
3828VA0305S
(NF01DC,
067M TX,
373-026H)
ON/OFF
INPUT VOLUME
SELECT
What is
a
Plasma
Display
?
If voltage is inputted to gas in glass panels, ultraviolet rays is outputted and fused with a fluorescent substance. At this moment, light is emitted. A Plasma Display is a next generation flat
Display using
160°
-
this
Wide
phenomenon.
angle range
of vision
A Plasma Display provides more than 160°
without distortion from any direction.
Easy
angle range
of vision
can
get
a
picture
same
class
products
so
that you
can
screen
The screen of
theater.
Plasma
a
Display
Multimedia Plasma
A Plasma
is 42"
so
Display
can
explanation
that you
can
get vivid experience
as
if you
are
in
a
Display
be connected with
ference, game, internet and so on.
The
that you
installation
A Plasma Display is much lighter and smaller than other
install the Plasma Display at the desired place.
Big
so
a
computer
so
that you
about coloured dots may be
can use
present
on
it
as a screen
PDP
for
con-
screen
The PDP which is the display device of this product is composed of 0.9 to 2.2 million cells and a
few cell defects can occur in the manufacture of the PDP. Several coloured dots visible on the
screen would be acceptable, in line with other PDP manufacturers and would not mean that the
PDP is faulty. We hope you will understand that the product which corresponds to this standard
is regarded as acceptable. It means that it could not be changed or refunded.
We promise that we'll do our best to develop our technology to minimize the cell defects.
WARNING
This is Class B
in which
case
product.
the
user
In
a
domestic environment this
may be
required
to take
product may
adequate measures.
cause
radio interference
WARNING
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
Contents
First step
Safety Instructions ....................................................4
Monitor Overview
Controls of the Monitor .............................................8
Controls of the remote control ................................12
Monitor Installation .................................................14
Equipment Connections and Setup
Watching VCR ........................................................16
Watching Cable TV.................................................17
Watching external AV source..................................18
Watching DVD ........................................................19
Watching DTV.........................................................20
Connecting PC .......................................................21
Function checking in PC mode ..............................23
Adjusting in PC mode .............................................24
PIP function ............................................................27
Using
the remote control ........................................30
Basic Features Setup and Operation
Turning on the Monitor ...........................................31
Selecting the on screen language ..........................32
Function checking...................................................33
Sleep Timer
Setting Sleep
Timer
(Monitor
turn-off
time)
............34
Picture & Sound
Auto picture control ................................................35
Adjusting picture condition .....................................36
DRP (Digital Reality Picture) ..................................37
Selecting menu options ..........................................38
Adjusting Sound: Bass, Treble, Balance ................39
Auto sound control .................................................40
AVL (Auto volume leveler) ......................................41
Special Features
Using Still function ..................................................42
Adjusting OSD Transparency .................................43
Adjusting colour temperature ................................44
Setting picture format .............................................45
External control device setup .................................46
Others
Troubleshooting check list ......................................54
Product specifications.............................................55
Safety
-
Instructions
It is recommended that this product only be used at an altitude of less than
6562 feet (2000m) to get the best quality picture and sound.
WARNING
Indorstali
NOTES
Do not place the Monitor in
direct sunlight or near heat
sources such as heat registers,
stove and so on.
This may
-
cause a
This plasma
be mounted
display is designed
horizontally (wide
to
viewing).
fire.
WARNING
Do not
the Monitor in
such as a bathany place where it
use
damp place
room or
OutdorInsali
is
likely
to
get
wet.
Bend antenna cable between
inside and outside building to prevent rain from flowing in.
-
This may cause a fire or could
give an electric shock.
-
WARNING
NOTES
Earth wire should be connected.
-
-
Power
-
If the earth wire is not connected,
there is possible a danger of electric
shock caused by the current leakage.
If grounding methods are not possible, a separate circuit breaker should
be employed and installed by a qualified electrician.
Do not connect ground to telephone
wires, lightning rods or gas pipe.
Short-circuit
breaker
4
This may cause water damaged inside
the Monitor and could give an electric
shock.
Never touch the power
with a wet hand
-
This may
cause an
plug
electric shock.
*
Safety
instructions have two kinds of
WARNING
NOTES
information, and each meaning of it is
below.
as
The violation of this instruction may
cause
serious
The violation of this instruction may
cause
light injuries
injuries
or
and
even
damage
death.
of the
product.
Take
care
of
danger that may happen
under
specific condition.
NOTES
Disconnect from the mains
and remove all connections
before moving.
Do not place the Monitor in a
built-in installation such as a
bookcase or rack.
-
Ventilation
required.
When
installing
the Monitor
on a
table, be careful not to place the
edge
-
of its stand.
This may cause the Monitor to fall,
causing serious injury to a child or
adult, and serious damage to the
Monitor.
NOTES
Do not place an outside antenna in
the vicinity of overhead power lines
other electric light or power circuits.
-
This may
cause an
electric shock.
or
There should be enough distance between an
outside antenna and power lines to keep the former from touching the latter even when the
antenna falls.
-
This may cause
an electric shock.
NOTES
Do not pull the cord but the
when unplugging.
plug
-
This may
cause a
fire.
Ensure the power cord
doesn't trail across any hot
objects like a heater.
-
This may cause
tric shock.
a
fire
or an
elec-
Do not plug when the power
cord or the plug is damaged
or the connecting part of the
power outlet is loose.
-
This may cause a fire
an electric shock.
or
FirstepMonvwCcBaSlmPu&df
Others
5
Safety
Instructions
WARNING
WARNING
Do not place anything
containing liquid on
top of the Monitor.
-
Using
This may cause a fire
could give an electric
shock.
or
Do not insert any
into the
exhaust vent.
Do not
object
-
place heavy
objects
on
the
Monitor.
This may cause a fire
could give an electric
shock.
or
-
This may
injury
to
a
cause
child
serious
adult.
or
WARNING
Do not use water the Monitor
while cleaning.
-
Cleanig
This may cause damaged the
Monitor or could give an electric
shock.
In case of smoke or strange
smell from the Monitor, switch it
off ,unplug it from the wall outlet
and contact your dealer or service center.
-
This may cause a fire
an electric shock.
or
could
give
WARNING
Do not attempt to service
the Monitor yourself.
Contact your dealer or service center.
Others
6
-
This may cause damaged the
Monitor or could give an electric
shock.
During
unplug
a
lightning thunder,
the Monitor from the
wall outlet and don't touch an
antenna cable.
-
This may cause damaged the
Monitor or could give an
electric shock.
NOTES
NOTES
Dispose of used batteries
carefully to protect a child
from eating them.
-
In
case
to
see a
When moving the Monitor
assembled with speakers do
not carry holding the speak-
Avoid having a fixed image
remain on the screen for a
long period of time. Typically
a frozen still picture from a
VCR, 4:3 picture format or if
a CH label is present; the
fixed image may remain
visible on the screen.
ers.
that it eats them, take it
doctor immediately.
-
This may
cause
the Monitor to
fall, causing serious injury
child or adult, and
to
a
serious
damage
to the
Monitor.
NOTES
Unplug this product from the wall outlet
before cleaning. Do not use liquid cleaners
or aerosol cleaners.
-
This may cause damaged the Monitor
an electric shock.
or
could
Contact the service center once a year to
clean the internal part of the Monitor.
-
Accumulated dust
can cause
mechanical failure.
give
NOTES
The distance between eyes
and the screen should be
about5~7timesaslongas
diagonal length of the
screen.
-
If not, eyes will strain.
Unplug the Monitor from the
wall outlet when it is left
unattended and unused for
long periods of time.
-
Accumulated dust may cause
fire or an electric shock from
deterioration or
electric leakage.
a
Only
use
teries.
-
the
specified
bat-
This make cause damaged the
Monitor or could give an electric
shock.
FirstepMonvwCcBaSlmPu&df
Others
7
Controls of the Monitor
<Front Panel>
ON/OFF
INPUT
SELECT
ON/OFF
VOLUME
MAIN POWER BUTTON
REMOTE CONTROL SENSOR
INPUT
SELECT
VOLUME
POWER/STANDBY INDICATOR
Illuminates red in standby
Illuminates green when the
Monitor is switched on
INPUT SELECT BUTTON
POWER BUTTON
VOLUME (Φ,Γ) BUTTON
8
<Back Panel>
AV INPUT
EXTERNAL SPEAKER
(+)
RL
()
()
(+)
EXTERNAL
SPEAKER (8Ω)
KNOBS
RL
AUDIO
S-VIDEO
RL
AUDIO <MONO> VIDEO
(+)
AV INPUT
EXTERNAL SPEAKER
(+)
RL
()
()
(MONO) VIDEO
COMPONENT
(DVD/DTV INPUT)
COMPONENT
S-VIDEO
(DVD/DTV INPUT)
Y
RGB
INPUT(PC/DTV INPUT)
YP
PBR
PB
R
RGB INPUT
PR
AV INPUT / S-VIDEO /
COMPONENT (DVD /DTV
INPUT) SOCKETS
AUDIO INPUT
(PC/DTV INPUT)
RS-232C
AC INPUT
L
AUDIO INPUT
R
RS-232C
AC INPUT
L
RGB INPUT (PC/DTV
/ AUDIO INPUT /
RS-232C SOCKET
INPUT)
POWER INPUT
SOCKET
This Monitor operates
on an AC mains supply,
the voltage is as indicated as inside back cover
of this manual. Never
apply DC power to the
Monitor.
9
FirstepMonvwCcBaSlmPu&df
Others
Accessories
POWER
SLEEP
INPUT SELECT
PSM
SSM
ARC
STILL
PIP
/TWINPICTURE
PIPINPUT
POSITION
MENU
VOL
POWER
REW
MUTE
OK
STOP
PLAY
VOL
P/STLL
FF
REC
D-sub 15
pin
cable
Power cord
Remote control handset
1.5V
LG TV
1.5V
AS
mark
Owner's Manual
Alkaline batteries
(optional)
Optional
-
-
Extras
Optional extras can be changed or modified
optional extras can be added.
Contract your dealer for buying these items.
AP-42WA20 series
(Tilt
10
wall
mounting bracket)
for
quality improvement
without any notification
AP-42WA10 series
(Wall mounting bracket)
new
Optional
-
-
Extras
Optional extras can be changed or modified
optional extras can be added.
Contract your dealer for buying these items.
for
quality improvement
without any notification
AP-42CA10 series
AP-42FA10 series
(Ceiling mounting bracket)
(Floor type stand)
AP-42DA10 series
AP-42SA10 series
(Desktop stand)
(Speakers)
AP-42SA10D series
AP-42SA10F series
(Speaker stand)
(Floor type speaker stand)
new
FirstepMonvwCcBaSlmPu&df
Others
Video cables
Audio cables
11
Controls of the remote control
-
When
using
the remote control aim it at the remote control
sensor
of the Monitor.
POWER
POWER
SLEEP
SLEEP (Refer to
p.34)
PSM (Refer to
p.35)
ARC (Refer to
p.45)
INPUT SELECT
PSM
SSM
ARC
STILL
PIP
PIP
(Refer
to
p.27)
PIP INPUT
(Refer
to
p.28)
/ TWIN PICTURE
PIP INPUT
POSITION
MENU
MUTE
MENU
OK
OK
VOL
POWER
STOP
P/STILL
REW
PLAY
FF
VOL
VOLUME (Φ,
Γ)
VCR BUTTONS
controls
a
LG video cassette
recorder.
12
REC
INPUT SELECT button
INPUT SELECT
SSM (Refer to
p.40)
STILL (Refer to
on
the
remote control
Each press of this button
the mode
p.42)
No function
POSITION (Refer to
as
changes
shown below.
Video
S-Video
RGB
Component
p.28)
MUTE
switches the sound
on or
off.
Δ/Ε
selects
a menu
item.
FirstepMonvwCcBaSlmPu&df
Others
13
Monitor Installation
-
The Monitor
can
desktop type,
be installed in various ways such
as
wall
mounting type,
etc..
Wall Mount Installation
?
The monitor
can
be installed
(For further information,
Guide'.)
on
refer to
the wall
'(Tilt)
the picture above.
mounting bracket Installation
as
wall
and
Setup
Tips
?
Install this monitor
only
in
a
location where
adequate
ventilation is available.
a.
4inch
mount minimum allowable
clearances for adequate
(Wall
1.18inch
ventilation)
4inch
4inch
4inch
14
Desktop pedestal installation
?
The Monitor
(For
can
be installed
on a
further information, refer to
desk
as
'Desktop
shown above.
stand Installation and
Setup Guide'.)
b.
(Pedestal
mount minimum
4inch
1.18inch
allowable clearances for
adequate ventilation)
4inch
4inch
FirstepMonvwCcBaSlmPu&df
Others
2.36inch
15
Watching VCR
-
When
(Video
-
-
-
connecting the Plasma Monitor with external equipments, match the colours of connecting ports
yellow, Audio(L) white, Audio(R) -red).
have a mono VCR, connect the audio cable from the VCR to the AUDIO(L/MONO) input of the
-
-
If you
Plasma Monitor.
If you connect an S-VIDEO VCR to the S-VIDEO
input, the picture quality is improved; compared to
connecting a regular VCR to the Video input.
Avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR, 4:3 picture format or if a CH label is present;
the fixed image may remain visible on the screen.
AV INPUT
EXTERNAL SPEAKER
(+)
AV INPUT
EXTERNAL SPEAKER
(+)
R
()
()
L
R
(+)
AUDIO L
R
()
() L (+)
S-VIDEO
RL
AUDO <MONO>VIDEO
COMPONENT
(480i/480p)
(DVDINPUT)
Y
PB
RGB PC NPUT
(VGASVGA/XGA)
COMPONENT
PB
RS-232C
RGB INPUT
AUDIO INPUT
(PC/DTV INPUT)
R
panel
RS-232C
L
of the Monitor
OUT
(R)
AUDIO
(L)
VIDEO
To watch VCR
IN
<Back
AC INPUT
L
PR
Back
S-VIDEO
AUDIO NPUT
R
PR
(DVD/DTV INPUT)
Y
(MONO) VIDEO
S-VIDEO
panel
of VCR>
INPUT SELECT
1
Press INPUT SELECT button
on
the
remote control and select Video.
(When connecting
S-Video.)
with S-Video, select
the
2
Insert a video tape into the VCR and
press the PLAY button on the VCR.
See VCR owner's manual.
Tips
?
16
To avoid picture noise
and monitor.
(interference),
leave
an
adequate
distance between the VCR
Watching Cable
-
After
you
to a cable TV service from
watch cable TV programming.
subscribing
can
AVINPUT
EXTERNAL SPEAKER
(+) R ()
(+)
R
()
()
L
R
(+)
AUDIO L
L
(+)
RL
AUDIO
(MONO) VIDEO
<MONO>
S-VIDEO
VDEO
COMPONENT
(480/480p)
(DVD INPUT)
Y
PB
RGBPC INPUT(VGA/SVGA/XGA)
PB
AUDIO INPUT
RS-232C
and
installing
a
converter,
AC INPUT
(PC/DTV INPUT)
PR
AUDIO INPUT
R
Back
UDI
provider
L
RGB INPUT
(DVD/DTV INPUT)
Y
local
R
PR
COMPONENT
S-VIDEO
AV INPUT
EXTERNAL SPEAKER
()
a
TV
panel
RS-232C
L
of the Monitor
VO
<Cable box>
TV
VCR
RF
Cable
To watch cable TV
Press INPUT SELECT button
1
on
the
INPUT SELECT
remote control and select Video.
Tune in cable service
2
provided
channels
using
the cable box.
Others
Tips
?
For further information regarding cable TV service, contact your local
cable TV service provider(s).
FirstepMonvwCcBaSlmPu&df
17
external AV
Watching
-
When
connecting
the Plasma Monitor with external
match the colours of
(+) R ()
(+)
R
()
()
L
AV INPUT
(+)
R
equipments,
connecting ports.
AV INPUT
EXTERNAL SPEAKER
EXTERNAL SPEAKER
source
AUDIO
L
(MONO) VIDEO
()
L
RL
AUDIO
(+)
S-VIDEO
<MONO>
S-VIDEO
VDEO
COMPONENT
RGB NPUT
(DVD/DTV INPUT)
Y
PB
(PC/DTVINPUT)
PR
COMPONENT
RS-232C
AC INPUT
L
RGB INPUT
(DVD/DTV INPUT)
Y
AUDIO INPUT
R
AUDIO INPUT
(PC/DTV INPUT)
PR
PB
<Back
R
panel
RS-232C
L
of the Monitor>
Camcorder
R
AUDIO
VIDEO
Video game set
To watch external AV
1
2
18
Press INPUT SELECT button
on
source
the
remote control of the monitor to select
Video.
Operate
the
corresponding
external
equipment.
INPUT SELECT
DVD
Watching
How to connect
?
Connect DVD video inputs to Y, PB, PR of COMPONENT
inputs to Audio sockets of AV INPUT.
AV INPUT
EXTERNAL SPEAKER
(+) R ()
(+)
R
()
()
L
R
(+)
AUDIO L
L
(+)
S-VIDEO
AV INPUT
EXTERNAL SPEAKER
()
RL
AUDIO
S-VIDEO
VDEO
COMPONENT
(480i/480p)
(DVDINPUT)
Y
PB
RGBPC INPUT(VGA/SVGA/XGA)
COMPONENT
PB
AUDIO INPUT
R
PR
(DVD/DTV INPUT)
Y
(MONO) VIDEO
<MONO>
RS-232C
AUDIO
AC INPUT
RGB INPUT
AUDIO INPUT
(PC/DTV INPUT)
PR
R
?
?
panel
RS-232C
L
of the Monitor>
(L)
<Back
How to
panel
of
a
DVD
player>
use
Press INPUT SELECT button on the remote control of the
monitor to select Component.
Try this after turning on the DVD player.
?
Component Input ports
can get better picture quality if you
connect DVD player with component input
You
ports
as
below.
Component ports
of the
Monitor
?
and audio
L
<Back
(R)
(DVD/DTV INPUT)
YPBPR
Input signal: 480i, 480p(60Hz)
Video
output ports
of DVD
player
Y
Y
Y
Y
Pb
B-Y
Cb
PB
Pr
R-Y
Cr
PR
19
FirstepMonvwCcBaSlmPu&df
Others
Watching
-
-
DTV
To watch digitally broadcast programs, purchase/connect a digital SET-TOP BOX.
You can select only the 16:9 picture format in DTV 1080i mode.
How to connect
?
user-supplied Digital Set-Top
a
Box
You can use either the Monitor's COMPONENT (Y, PB, PR) inputs or the single RGB-DTV
INPUT for video connections, depending on your Set-Top Box connectors. Then, make the
corresponding Audio connections. See the diagram below for either set up.
AV INPUT
EXTERNAL SPEAKER
R
(+)()
AV INPUT
EXTERNAL SPEAKER
(+)
R
()
()
L
R
(+)
AUDIO L
() L (+)
S-VIDEO
(MONO) VIDEO
COMPONENT
(480i/480p)
(DVD INPUT)
S-VIDEO
RL
AUDIO <MONO>VIDEO
Y
PB
RG BPC INPUT
COMPONENT
(DVD/DTV INPUT)
Y
PB
(VGASVGA/XGA)
AUDIO NPUT
R
PR
RS-232C
AC INPUT
L
RGB INPUT
(PC/DTV INPUT)
PR
AUDIO INPUT
R
RS-232C
L
<Back
panel
of the Monitor>
or
(R)
AUDIO
(L)
(R)
<
How to
?
Turn
on
(Refer
?
panel
of
a
digital SET-TOP BOX
(L)
DTV OUTPUT
>
use
the
digital SET-TOP BOX.
digital SET-TOP BOX.)
the remote control to select COMPONENT
to the owner's manual for the
Press INPUT SELECT button
DTV
20
Back
AUDIO
Input signal
on
Mode
Terminal
576p (50Hz)
1080i (50Hz)
or
RGB.
Component
RGB(DTV)
o
x
o
o
PC
Connecting
-
You
can
vivid
enjoy
and sound with
picture
connecting
a
PC with the Monitor.
How to connect
?
?
?
?
?
If the resolution of the the PC is over SXGA, there will be no picture on the Monitor.
Connect the signal cable from the monitor output port of the PC to the RGB INPUT (PC/DTV
INPUT) port of the Monitor.
Connect the audio cable from the PC to the Audio ports of the Monitor. (Audio cables not included
with the Monitor)
In case of using a sound card adjust PC sound properly.
To setup this monitor in your PC windows environment, select Normal, Standard or Default monitor.
This monitor does not support Plug and Play functionality.
AV INPUT
EXTERNAL SPEAKER
(+)
AV INPUT
EXTERNAL SPEAKER
(+)
R
()
()
L
<
How to
(+)
Back
R
AUDIO L
(MONO) VIDEO
panel
R()
()
L
RL
AUDIO
(+)
<MONO>
S-VIDEO
VIDEO
COMPONENT
(480i/480p)
(DVD INPUT)
Y
PB
RGB
PCINPUT(VGA/SVGAXGA)
PR
COMPONENT
S-VIDEO
(DVD/DTV INPUT)
Y
PB
AUDIO INPUT
R
RS-232C
AC INPUT
L
RGB INPUT
(PC/DTV INPUT)
PR
AUDIO INPUT
R
RS-232C
L
of the Monitor>
use
?
?
<On the remote control>
Press POWER button on the PC and press ON/OFF button
the Monitor. After this press
button on the Monitor or
press POWER button on the remote control of the monitor.
Press INPUT SELECT button on the remote control to
select RGB.
Set the resolution of PC under XGA (1024x768).
on
INPUT SELECT
?
(Refer
to page
22.)
Tips
?
?
To avoid burning an image on the Monitor screen, don't have a still picture on the screen
for a long period time.
If the resolution of the PC is over SXGA, connect the PC to the RGB INPUT(PC/DTV
INPUT) port of the Monitor after changing the resolution of the PC.
21
FirstepMonvwCcBaSlmPu&df
Others
Displayable
Monitor
Resolution
Specification
Horizontal
Frequency (KHz) Frequency (Hz)
640x350
640x400
640x480
800x600
832x624
1024x768
31.468
70.09
37.861
85.08
31.469
70.08
37.927
85.03
31.469
59.94
35.000
66.66
37.861
72.80
37.500
75.00
43.269
85.00
45.913
90.03
53.011
100.04
64.062
120.00
35.156
56.25
37.879
60.31
48.077
72.18
46.875
75.00
53.674
85.06
56.000
90.00
64.016
100.00
49.725
74.55
48.363
60.00
56.476
70.06
60.023
75.02
68.677
84.99
Tips
?
22
Vertical
Synchronization input
form
:
separate
Function
-
Select RGB
input
checking
in PC mode
source.
MENU
1
2
Press the MENU button.
Press the Δ / Ε button.
?
Each time you press this button you
PSM
Γ
85Γ
Brightness
50Γ
Colour
50Γ
Tint
0Γ
50Γ
Sharpness
ΔΕ Γ
OK
MENU
<Picture
SSM
Γ
Treble
50Γ
Bass
50Γ
Balance
0Γ
OK
Γ
MENU
<Sound
Language
Γ
Γ
Screen
Γ
Transparency
Γ
PIP
Γ
ΔΕ Γ
Γ
Γ
Temp.
OK
MENU
<Special
VOL
3
menu>
ARC
Set ID
VOL
menu>
Γ
AVL
Colour
below.
Γ
DRP
Contrast
ΔΕ
can see menus as
menu>
Press the Γ button and then press the Δ / Ε
or
Φ / Γ button to select a function you want to use.
?
FirstepMonvwCcBaSlmPu&df
Others
Press the OK button to exit.
23
Adjusting
Auto
-
-
-
in PC mode
configure
Select RGB
input source.
Automatically adjusts picture position
When watching PIP, Screen option is
and eliminates any
not available in
image shaking.
menu.
READY
Press the MENU button and then press the Δ / Ε button to
select
menu.
Press the Γ button.
MENU
VOL
Press the Δ / Ε button to select Screen and
then press the Γ button.
1
VOL
Language
Γ
ARC
Γ
Screen
Γ
Transparency
Γ
PIP
Γ
Set ID
Γ
Colour
Press the Δ / Ε button to select
Auto-configure and then press
the Γ button.
2
Γ
Temp.
Auto-configure
ΓToSet
Γ
ΓToSet
Γ
Γ
Phase
Γ
Reset
Γ
VOL
?
?
If
3
When Auto-configure has finished, "OK" will be shown on screen.
If the position of the image is incorrect, try Auto adjustment again.
picture
needs to be
,and Phase.
adjusted
more
after auto
adjustment, adjust
Tips
?
24
If the
image
is still not correct, your Monitor is
functioning properly
but needs further
adjustment.
Adjusting
-
and
Only adjust
horizontal / vertical
in RGB DTV
or
position
component 480p/576p/1080i.
READY
Press the MENU button and then press the Δ / Ε button to
select
menu.
Press the Γ button.
MENU
VOL
Press the Δ / Ε button to select Screen and
then press the Γ button.
1
Language
Γ
ARC
Γ
Screen
Γ
Transparency
Γ
PIP
Γ
Set ID
VOL
Colour
Press the Δ / Ε button to select
then press the Γ button.
2
or
ΓToSet
Γ
Γ
Temp.
and
Auto-configure
Γ
Γ
0
Γ
VOL
?
?
3
Select
Select
Phase
Γ
Reset
Γ
for vertical position adjustment.
for horizontal position adjustment.
Press the Φ / Γ button to adjust until you get desired horizontal
vertical position and then press the OK button.
?
or
The adjustment range of
is -50
+50.
The adjustment range of
is -100
+100.
Based on the input mode, the adjustment range of
or
may change.
Based on the VGA card, the adjustment range of
may be out of -100
+100 after auto configure.
Based on the input signal, the position of the picture may not change even
though you have adjusted the horizontal or vertical position with this function.
~
~
?
?
?
~
VOL
VOL
FirstepMonvwCcBaSlmPu&df
Others
OK
25
in PC mode
Adjusting
Adjusting phase
-
If the
picture isn't clear after auto adjustment and especially that characters
then adjust the picture phase manually.
When watching PIP, Screen option is not available in Special menu.
still trem-
are
bling,
-
READY
Press the MENU button and then press the Δ / Ε button to
select
menu.
Press the
(
Γ
MENU
1
button.
)
VOL
Press the Δ / Ε button to select Screen and
then press the Γ button.
Language
Γ
ARC
Γ
Screen
Γ
Transparency
Γ
PIP
Γ
Set ID
VOL
2
Colour
Press the Δ / Ε button to select Phase and
then press the Γ button.
ΓToSet
Γ
Γ
Temp.
Auto-configure
Γ
Γ
Γ
VOL
Press the Φ / Γ button to
3
adjust phase
Phase
Γ
Reset
Γ
30
and then press the OK but-
ton.
?
The
adjustment range
of Phase is 0
63.
~
OK
VOL
VOL
Initializing
?
26
To initialize the adjusted value, select Reset with the Δ / Ε button and then
press the Γ button.
PIP function
-
-
-
-
-
-
pressing PIP.
following resolution;
640x480, 800x600, 1024x768 (only in Vertical frequency 60 Hz)
When you select RGB PC for main picture in PIP, you can watch video, cable TV
Color of main picture may be different from sub picture's in PIP mode.
If input source for main picture is changed while in PIP, sub picture will disappear.
When watching PIP, Screen option is not available in
menu.
Select RGB
input
source
This function works
only
before
in the
Watching
PIP
the PIP
(Picture
in
or
DVD for sub
picture.
Picture)
Press the PIP button.
?
Each time you press PIP
PIP size as below.
PIP
or Φ
/ Γ button, you
PIP [L]
[S]
PIP
Φ
PIP[S]
can
change
the
Off
Γ
<Small PIP>
PIP
Φ
PIP[L]
<Large
PIPΦOff
Γ
PIP>
Γ
FirstepMonvwCcBaSlmPu&df
Others
<Off>
27
PIP function
Selecting
PIP INPUT
the
Press the PIP INPUT button in PIP mode.
?
Each time you press PIP INPUT button, you
Video, S-Video and Component.
Component
PIP
Moving
POSITION
Input
Φ
source
Video
the Sub
only
can
change
works in 480i mode.
Γ
picture
Press the POSITION button in PIP mode.
?
28
input signal
Each press of the POSITION button will change the
the sub picture on the screen as shown below.
position
of
Selecting
-
-
-
PIP sound
options
This function works
only in the following resolutions;
640x480, 800x600, 1024x768 (only in Vertical frequency 60 Hz)
To use this function, connect PC/DTV video port to RGB INPUT(PC/DTV INPUT) socket and
nect PC/DTV audio port to AUDIO INPUT.
Sound Select is always selected Sound[M] regardless of prior sound choice.
con-
READY
Press the MENU button and then press the Δ / Ε button to
select
menu.
Press the
(
Γ
MENU
1
)
button.
VOL
Press the Δ / Ε button to select PIP and then
press the Γ button.
Language
Γ
ARC
Γ
Screen
Γ
Transparency
Γ
PIP
Γ
Set ID
VOL
2
Press the Δ / Ε button to select Sound
Select and then press the Γ button.
Colour
ΓToSet
Γ
Γ
Temp.
PIP
Γ
Input
Γ
Sound Select
Γ
Sound
[M]
Position
Γ
Sound
[S]
PIP
Γ
VOL
3
Press the Δ / Ε button to select Sound [M]
Sound [S] and then press the OK button.
or
OK
Input
Γ
Sound Select
Γ
Sound
[M]
Position
Γ
Sound
[S]
FirstepMonvwCcBaSlmPu&df
Others
29
Using
Inserting
the remote control
batteries
?
the
Open
battery compartment
cover on
side and insert the batteries with correct
?
Apply
two 1.5V alkaline batteries of AAA
Don't mix the used batteries with
?
Notes for
Make
sure
objects
30
using
these
are no
between the
new
Install the batteries with the correct
the back
polarity.
type.
batteries.
polarities.
the remote control
Don't
place
near a
the remote control
heater
remote control and its
Strong impact
sensor.
trol may
or
cause
damp place.
on
the remote
operation
con-
failure.
Signal
from the remote control
may be disturbed by sun light or
other strong light. In this case,
turn the set to other direction.
Turning
-
When
using
Turning
on
control,
aim it at its
the Monitor
just
Connect power cord
1
sensor on
the Monitor
the Monitor.
after installation
correctly.
Press the ON/OFF button on the Monitor. At this moment, the Monitor is
switched to standby mode. Press the
or INPUT SELECT button on the
Monitor or press the POWER or INPUT SELECT button on the remote control
and then the Monitor will be switched on.
2
Turning
1
the remote
on
on
the Monitor
(power
cord is still
If the Monitor is turned off with the
connected)
button
on
the Monitor
Press the
or INPUT SELECT button on the Monitor or press the POWER
INPUT SELECT button on the remote control and then the Monitor will be
switched on.
or
2
3
If the Monitor is turned off with the ON/OFF button
?
Press the ON/OFF button
on
the Monitor to turn
If the Monitor is turned off with the remote
on
on
the Monitor
the Monitor.
control, then the ON/OFF but-
ton on the Monitor
?
Press the ON/OFF button on the Monitor and then press the
or INPUT
SELECT button on the Monitor or press the POWER or INPUT SELECT button on the remote control and then the Monitor will be switched on.
Tips
Adjusting
Volume(Γ)
?
sound.
volume level
button increases the sound and
volume(Φ)
FirstepMonvwCcBaSlmPu&df
Others
button decreases the
31
Selecting
the
language
on screen
READY
Press the MENU button and then press the Δ / Ε button to
select
menu.
Press the Γ button.
MENU
1
VOL
Press the Δ / Ε button to select
Language and then press the Γ button.
Language
Γ
Screen
Γ
Transparency
Γ
PIP
Γ
Set ID
Colour
Γ
Temp.
VOL
2
3
Press the Δ / Ε button to select the desired
Press the OK button.
OK
32
Γ
ARC
language.
Γ
Function
-
Select VIDEO
input
source.
1
MENU
checking
Press the MENU button.
Press the Δ / Ε button.
2
?
Each time you press this button you
shown below.
PSM
Γ
DRP
Γ
Contrast
100
50Γ
Colour
50Γ
Tint
0Γ
50Γ
Sharpness
OK
ΔΕ Γ
MENU
<Picture
SSM
Γ
Treble
50Γ
Bass
50Γ
Balance
ΔΕ Γ
0Γ
OK
MENU
<Sound
Language
Γ
Γ
Screen
Γ
Transparency
Γ
PIP
Γ
ΔΕ Γ
Γ
Γ
Temp.
OK
MENU
<Special
3
menu>
ARC
Set ID
VOL
menu>
Γ
AVL
VOL
Γ
Brightness
Colour
can see menus
menu>
Press the Γ button and then press the Δ / Ε
or
Others
Φ / Γ button to select a function you want to use.
?
FirstepMonvwCcBaSlmPu&df
Press the OK button to exit.
33
Setting sleep
<
Sleep Timer turns the
SLEEP
timer
Monitor off after
a
preset time.
>
Press the SLEEP button to set sleep time.
Each time you press SLEEP button, the next
preset setting time is changed as shown below.
Φ---Γ
Φ10Γ
Φ20Γ
Φ30Γ
Φ120Γ
Φ90Γ
Φ60Γ
Φ240Γ
Φ180Γ
r
?
Φ---Γ
To release sleep time setting, press the SLEEP or
Φ / Γ button repeatedly to select Φ
Γ.
1' is displayed, one minute before the Monitor
is due to switch off.
---
'
?
Tips
?
?
?
34
When the sleep time you want is displayed on the screen, don't press the
SLEEP button. After 20 seconds, the screen display disappears and sleep
time is set.
To check remaining sleep time after setting, press the SLEEP button just once.
If you turn the Monitor off after setting the sleep timer, the setting is erased.
The sleep timer will then have to be set again.
Auto
<
-
picture
control
Use PSM to set the Monitor for the best
This function is not available in RGB
PSM
PSM
1
2
PC,
picture appearance
>
PIP.
(Picture Status Memory)
Press the PSM button.
Press the PSM or Φ / Γ button to select your
desired picture condition.
PSM
?
Φ
?
Γ
Each press of Φ / Γ button
shown below.
Dynamic
?
Dynamic
changes
Mild
the
screen
display
as
User
You can also select Dynamic, Mild or User in the
Picture menu.
The picture Dynamic and Mild are programmed for good
picture reproduction at the factory and cannot be changed.
FirstepMonvwCcBaSlmPu&df
Others
35
Adjusting picture
-
PIP inset
settings
are
not
condition
adjustable.
READY
Press the MENU button and then press the Δ / Ε button to
select
menu.
Press the Γ button.
MENU
1
VOL
Use the Δ / Ε button to select
Contrast and then press the Γ button.
(to adjust contrast setting)
PSM
Γ
DRP
Contrast
Γ
100
Γ
Brightness
50Γ
Colour
50Γ
Tint
Sharpness
0Γ
50Γ
VOL
?
2
Adjust Brightness, Colour, Tint
Sharpness in the same way.
and
Use the Φ / Γ button to make appropriate adjustments and then press the
OK button.
?
Press the Δ / Ε button to select other items.
PSM
DRP
36
VOL
OK
Γ
70Γ
Brightness
50Γ
Colour
Tint
Sharpness
VOL
Γ
Contrast
0Γ
0Γ
50Γ
DRP
<
Picture)
(Digital Reality
Soft
DRP allows you to select Clear
-
or
for your
picture appearance
>
This function works in video, component 480i mode.
READY
Press the MENU button and then press the Δ / Ε button to
select
menu.
Press the Γ button.
MENU
1
VOL
Press the Δ / Ε button to select DRP
and then press the Γ button.
PSM
2
Press the Δ / Ε button to select
Dynamic or Mild.
Γ
Dynamic
Γ
Mild
Brightness
Colour
50Γ
Sharpness
0Γ
50Γ
PSM
Γ
DRP
Contrast
100
Γ
Dynamic
Γ
Mild
Brightness
50Γ
Colour
50Γ
Tint
Sharpness
3
100
50Γ
Tint
VOL
Γ
DRP
Contrast
0Γ
50Γ
Press the OK button.
OK
FirstepMonvwCcBaSlmPu&df
Others
37
Selecting
-
Use this
option
when
viewing
menu
the video
options
input.
READY
Press the MENU button and then press the Δ / Ε button to
select
menu.
Press the Γ button.
MENU
1
VOL
Use the Δ / Ε button to select Screen
and then press the Γ button.
Language
Γ
ARC
Γ
Screen
Γ
TV
Transparency
Γ
VCR
PIP
Γ
Set ID
Γ
Colour
Temp.
Γ
VOL
2
UsetheΔ/ΕbuttontoselectTVor
VCR.
?
?
Select the VCR option if watching
Select the TV option for other
equipment.(Except VCR)
?
Press the OK button.
OK
38
VCR.
Γ
Γ
Screen
Γ
TV
Transparency
Γ
VCR
PIP
Γ
Set ID
Γ
Colour
Each time you press the Δ / Ε button you
toggle between TV and VCR.
VOL
3
a
Language
ARC
Temp.
Γ
Adjusting
sound
READY
Press the MENU button and then press the Δ / Ε button to
select
menu.
Press the Γ button.
MENU
1
VOL
Use the Δ / Ε button to select Treble
and then press the Γ button.
(if adjusting treble)
SSM
Γ
AVL
Γ
Treble
50
Bass
50Γ
Balance
Γ
0Γ
VOL
?
2
Adjust
Bass and Balance in the
same
way.
Use the Φ / Γ button to make appropriate adjustment and then press the
OK button.
?
Press the Δ / Ε button to select other items.
SSM
AVL
Γ
Γ
Treble
70Γ
Bass
50Γ
Balance
0Γ
OK
VOL
VOL
FirstepMonvwCcBaSlmPu&df
Others
39
Auto sound control
SSM
?
SSM
This function lets you enjoy the best sound without any special adjustment because the Monitor automatically selects the appropriate sound
option based on the program content.
1
Press the SSM button.
2
Press the SSM
desired sound.
SSM
?
or Φ
ΦUserΓ
Each press of SSM
play as below.
or Φ
Flat
?
40
/ Γ button
changes
the
screen
dis-
Movie
Speech
User
?
/ Γ button to select your
Music
You can also select Flat, Speech, Movie, Music or User
in the Sound menu.
The sound Flat, Speech, Movie and Music are programmed for good sound reproduction at the factory and
cannot be changed.
AVL
<
(Auto Volume Leveler)
This feature maintains
an
equal volume level;
even
if you
change channels >
READY
Press the MENU button and then press the Δ / Ε button to
select
menu.
Press the Γ button.
MENU
1
VOL
Press the Δ / Ε button to select AVL
and then press the Γ button.
SSM
AVL
Γ
Γ
On
Treble
50Γ
Off
Bass
50Γ
Balance
0Γ
VOL
2
PresstheΔ/ΕbuttontoselectOnor
Off.
SSM
AVL
Γ
On
50Γ
Off
Bass
50Γ
Balance
3
Γ
Treble
0Γ
Press the OK button.
FirstepMonvwCcBaSlmPu&df
Others
OK
41
Using Still
-
-
This feature isn't available for RGB PC
Use with A/V
or
COMPONENT video
1
STILL
input
inputs.
function
source.
Press the STILL button.
?
?
You can still the current picture.
The sub picture is stilled in PIP mode.
<Moving image>
<Still
2
To return to normal
image>
viewing, press
the STILL button
again.
Tips
?
42
If still picture is on the screen for more than 5 minutes, the image becomes
dark.
If another function is activated, normal brightness of the screen is restored.
Adjusting OSD Transparency
READY
Press the MENU button and then press the Δ / Ε button to
select
menu.
Press the Γ button.
MENU
1
VOL
Press the Δ / Ε button to select
Transparency and then press the Γ
button.
Language
Γ
ARC
Γ
Screen
Γ
Transparency
Γ
PIP
Γ
Set ID
Γ
Colour
Temp.
3
Γ
VOL
2
Press the Φ / Γ button to
transparency.
?
The adjustment range of
1~4.
VOL
3
adjust OSD
Transparency
is
Language
Γ
ARC
Γ
Screen
Γ
Transparency
Γ
PIP
Γ
Set ID
Γ
Colour
Temp.
3
Γ
VOL
Press the OK button.
OK
FirstepMonvwCcBaSlmPu&df
Others
43
Adjusting
-
-
colour temperature
You should be adjust colour temperature in PC mode again although colour temperature is
adjusted in other input source.
To initialize adjusted value, select '0' in Red, Green and Blue.
READY
Press the MENU button and then press the Δ / Ε button to
select
Press the Γ button.
menu.
MENU
1
VOL
Press the Δ / Ε button to select Colour
Γ button.
Temp. and then press the
VOL
2
Language
Γ
ARC
Γ
Screen
Γ
Transparency
Γ
PIP/DW
Γ
Set ID
Γ
Colour
Press the Δ / Ε button to select Red and
then press the Γ button.
(to adjust Red setting)
Temp.
Γ
Red
Γ
Green
Γ
Blue
Γ
ΓToSet
0
VOL
?
3
Adjust
same
Use the Φ / Γ button to make
press the OK button.
VOL
?
44
Green and Blue in the
The
VOL
adjustment range
way.
appropriate adjustments
OK
of Red, Green and Blue is -5
+5.
~
and then
Setting picture format
-
-
-
With the RGB PC
input, you can select either 16:9 or 4:3 screen aspect ratios.
With the RGB DTV 1080i input, you can only select 16:9 screen aspect ratios.
If 4:3 mode is used for
a
long time,
the outline of the
image may
remain
on
the
screen
after
FirstepMonvwCcBaSlmPu&d
to the 16:9 screen.
-
you change
Don't display 4:3
ARC
format
picture
on screen
above 10 hours
continuously.
Press the ARC button to select
format.
?
a
desired
Each time you press ARC or Φ / Γ button, you
select 16:9, 4:3 or Zoom alternatively.
picture
can
ARCΦ16:9Γ
<16:9>
ARCΦ4:3Γ
<4:3>
Specialfturs
ARCΦZoomΓ
<Zoom>
?
You
can
also select 16:9, 4:3
or
Zoom in the
Special
Others
menu.
45
External Control Device
-
Connect the RS-232C
input jack to an external control
externally.
device
(such
as a
computer
or an
Setup
A/V control
system)
and
control the Monitor's functions
How to connect external control
?
Connect the serial
?
RS-232C connection cables
?
The Monitor remote control and
by
a
PC
computer
port of the control device
or
are
to the RS-232C jack on the Monitor back panel.
supplied with the Monitor.
front panel controls (except main power) will not be functional
not
other external device.
AV INPUT
EXTERNAL SPEAKER
R
(+)()
AV INPUT
EXTERNAL SPEAKER
(+)
R
()
()
L
(+)
Back
46
equipment
R
AUDIO
panel
L
(MONO) VIDEO
() L (+)
S-VIDEO
RL
AUDIO <MONO>VIDEO
COMPONENT(480/480p)
(DVD INPUT)
Y
PB
PR
COMPONENT
S-VIDEO
(DVD/DTV INPUT)
Y
PB
PR
of the Monitor
RGBPC INPUT
(VGA/SVGAXGA)
AUDIOINPUT
R
RS-232C
AC INPUT
L
RGB INPUT
(PC/DTV INPUT)
AUDIO INPUT
R
L
RS-232C
if the Monitor is controlled
Type
*
of connector
No.
Pin
1
No connection
RXD
3
TXD
9-pin
male
1
5
(Receive data)
(Transmit data)
(DTE side ready)
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
9
No Connection
a
D-Sub
name
2
Use
:
Pin No.4 and
(DCE side ready)
(Ready to send)
(Clear to send)
9
Pin No.6 must
be connected
on
6
monitor side.
null modem cable.
Wire the 7-Wire cable
*
so that each pair of data lines cross between the two devices. These data line pairs are RXD
(Receive data) and TXD (Transmit data), DTR (DTE side ready) and DSR (DCE side ready), and RTS (Ready to send) and
CTS (Clear to send).
When using the 3-Wire cable connected to RXD, TXD and GND; Pin No. 4 (DTR) and Pin No. 6 (DSR) must be connected
to the monitor. (The cable must be disconnected from the Monitor to be able to use the remote control and Monitor front
panel controls.)
With the RS-232 input connected, the Monitor cannot be controlled by both an external control device and the remote control at the same time. The Monitor can only be controlled by either the remote control or the external control device.
RS-232C
configurations
7-wire
(Standard
PC
configuration
(Not standard)
PDP
PC
RXD
3
TXD
RXD
TXD
2
RXD
TXD
5
GND
GND
6
DSR
DTR
4
DTR
DSR
8
CTS
RTS
7
RTS
CTS
GND
DTR
DSR
RTS
CTS
2354678
DB 9
7-Wire Cable
?
3-wire
configuration
RS-232C cable)
Control line
3-Wire Cable
adjust-
ment and remote control
adjustment using a control line.
is high, the monitor is controlled by
the external control device. If the control line is
Monitor is controlled
by
2354678
low, the
the Monitor's remote control.
?
When
using
GND
DTR
DSR
RTS
CTS
DB9
Configuration
a
3-Wire cable
configuration
line. The external control device must
"change
RXD
3254678
DB9
Configuration
Note: If the control line
TXD
DB9
The Monitor is available to switch between external
PDP
into remote control
there is
no
control
put the Monitor into the
adjustment
mode"
The Monitor will then be able to be controlled
(see page 53).
by the remote
control. If the Monitor is turned back on, it will revert back to
external device control.
FirstepMonvwCcBaSlmPu&df
Others
47
External Control Device
Setup
SET ID
?
Use this function to
specify
a
monitor ID number.
READY
Press the MENU button and then press the Δ / Ε button to
select
menu.
Press the Γ button.
MENU
1
VOL
UsetheΔ/ΕbuttonstoselectSETIDand
then press the Γ button.
Language
Γ
ARC
Γ
Screen
Γ
Transparency
Γ
PIP
Γ
Set ID
VOL
2
Colour
UsetheΦ/Γ buttontoadjustSETID
until you get desired monitor ID number.
?
The
adjustment
range of SET ID is 1
99.
~
Language
Γ
Γ
Screen
Γ
Transparency
Γ
PIP
Γ
Set ID
48
VOL
Γ
Temp.
1
Γ
ARC
Colour
VOL
Γ
Temp.
Γ
1
-
The RS-232C
input jack
is used to control the Monitor's functions
*
Communication Parameters
using
[Cr]
:
an
external control device.
Return
Carriage
ASCII code '0x0D'
?
Baud rate
:
2400
Data
length : 8
Parity : None
?Stopbit:1bit
?
bps (UART)
*[]
'space (0x20)'
[Set ID][:][OK][x][Data][x]
Communication code
:
ASCII code
*
*
ASCII code
OK Acknowledgement
?
?
:
bits
If the command interval is
seconds, only Command
Be careful when
using
interrupted for more
1 will be recognized.
The Monitor transmits ACK
on
than 4
this format when
(acknowledgement) based
receiving normal data. At this
time, if the data is data read mode, it indicates present
status data. If the data is data write mode, it returns
the data of the PC computer.
the power command.
Error Acknowledgement
[Set ID][:][NG][x]
*
Command Reference List
The Monitor transmits ACK
on
01. Power
02.
03.
Select
Input
Aspect
Ratio
p
0~1
i
0~3
this format when
(acknowledgement) based
receiving abnormal data from
non-viable functions
or
communication
errors.
r
0~2
04. Screen mute
m
0~1
05. Volume mute
w
0~1
06. Volume control
v
0~64
07. Contrast
k
0~64
Γ To control Power On/Off of the Monitor.
08.
b
0~64
Transmission
09. Colour
c
0~64
10. Tint
t
0~64
11.
Brightness
s
0~64
12. OSD select
d
0~1
13. Abnormal state
a
0~1
14. PIP
z
0~3
Sharpness
01. Power
(Command:p)
[p][ ][Set ID][ ][Data][Cr]
Data
0
:
Power Off
1:PowerOn
*
Example : Power on
Type:P31'0x0D'
for set ID No.3.
e
0~1
Acknowledgement
16. PIP sound select
u
0~1
[Set ID][:][OK][x][Data][x]
17. PIP
x
0~3
j
0~1
15. PIP
input
select
position
18. remote control
adjustment
mode
Data
0
:
Power Off
1:PowerOn
*
In
example
:
Monitor Acknowledges power
on
for set ID No.3.
Γ To show Power On/Off.
Transmission
Transmission/Receiving
Protocol
Transmission
Acknowledgement
[Command][ ][Set ID][ ][Data][Cr]
*
*
[Command]
[Set ID]
[p][ ][Set ID][ ][FF][Cr]
:
To control PDP set.
:
You
can
adjust
[Set ID][:][OK][x][Data][x]
the set ID to choose
Data
desired monitor ID number in
See page 48.
is1~99.
menu.
When
selecting
Set ID
special
Adjustment range
'0', every connected
PDP set is controlled.
*
[DATA]
:
*
0
:
Power Off
1
:
Power On
2
:
Power On
3
:
Power On
4
:
Power On
(RGB)
(Video)
(Component)
(S-Video)
To transmit command data.
In like manner, if other functions transmit 'FF' data
based on this format, Acknowledgement data feed
Transmit 'FF' data to read status of
back
presents
status about each function.
command.
49
FirstepMonvwCcBaSlmPu&df
Others
External Control Device
02.
Input
select
Γ To select input
You
(Command:i)
source
also select
can
SELECT button
on
an
for the Monitor.
input
source
using
the INPUT
the Monitor's remote control.
Transmission
04. Screen mute
[i][ ][Set ID][ ][Data][Cr]
Γ To select
Data
Transmission
0
:RGB
1
:
2
:
3
:
AV
(Video)
Component
S-AV (S-Video)
:
:
3
:
0
:
Screen mute
1
:
Screen mute off
AV
0
:
Screen mute
1
:
Screen mute off
Γ To control volume
Aspect
Ratio
Γ To adjust the
You
You
(Command:r)
Wide
1
:
Normal
2
:
Full
screen
[Set ID][:][OK][x][Data][x]
*
0
:
Wide
1
:
Normal
2
:
Full
Using
the PC
(16:9)
(4:3)
(Zoom)
screen
screen
screen
input,
you select either 16:9
or
4:3
screen
aspect ratio.
*
Using
the DTV 1080i
screen
50
aspect ratio.
using
the MUTE button
[w][ ][Set ID][ ][Data][Cr]
Data
Data
Acknowledgement
Data
mute
input,
0
:
Volume mute
1
:
Volume mute off
on
(Volume off)
(Volume on)
[Set ID][:][OK][x][Data][x]
(16:9)
(4:3)
(Zoom)
screen
screen
mute on/off.
adjust
Acknowledgement
[r][ ][Set ID][ ][Data][Cr]
:
also
(Command:w)
Transmission
Transmission
0
can
(Picture off)
(Picture on)
format.
screen
also
can
(Picture off)
(Picture on)
remote control.
adjust the screen format using the ARC
(Aspect Ratio Control) button on remote control or in
the Special menu.
Data
on
(Video)
Component
S-AV (S-Video)
05. Volume mute
03.
on
[Set ID][:][OK][x][Data][x]
Data
0:RGB
1
mute on/off.
Acknowledgement
[Set ID][:][OK][x][Data][x]
2
screen
(Command:m)
[m][ ][Set ID][ ][Data][Cr]
Data
Acknowledgement
Data
Setup
you
can
only
select 16:9
0
:
Volume mute
1
:
Volume mute off
on
(Volume off)
(Volume on)
on
06. Volume control
09. Colour
(Command:v)
Γ To adjust the
Γ To adjust volume.
You
on
also
can
adjust
(Command:c)
You
volume with the volume buttons
remote control.
colour.
screen
also
can
adjust
colour in the Picture
menu.
Transmission
Transmission
[c][ ][Set ID][ ][Data][Cr]
[v][ ][Set ID][ ][Data][Cr]
Data
Data
Min:0~Max:64
Min:0~Max:64
Refer to 'Real data
*
as
shown below.
mapping'
as
shown below.
Acknowledgement
Acknowledgement
[Set ID][:][OK][x][Data][x]
[Set ID][:][OK][x][Data][x]
Data
Refer to 'Real data
*
mapping'
Data
Min:0~Max:64
Min:0~Max:64
10. Tint
07. Contrast
(Command:k)
Γ To adjust the
You
Γ To adjust
You
screen
also
can
contrast.
adjust
screen
adjust
tint.
tint in the Picture
menu
menu.
[t][ ][Set ID][ ][Data][Cr]
Data
[k][ ][Set ID][ ][Data][Cr]
Refer to 'Real data
Red:0~Green:64
Refer to 'Real data
*
Min:0~Max:64
*
also
can
Transmission
contrast in the Picture
Transmission
Data
(Command:t)
mapping'
as
shown below.
Acknowledgement
mapping'
as
shown below.
Acknowledgement
[Set ID][:][OK][x][Data][x]
Data
Red:0~Green:64
[Set ID][:][OK][x][Data][x]
Data
Min:0~Max:64
11.
08.
Brightness (Command:b)
Sharpness (Command:s)
Γ To adjust the
You
Γ To adjust
You
also
can
brightness.
adjust brightness
screen
Min:0~Max:64
Refer to 'Real data
*
Min:0~Max:64
Acknowledgement
menu
[s][ ][Set ID][ ][Data][Cr]
[b][ ][Set ID][ ][Data][Cr]
Refer to 'Real data
the Picture
menu.
Data
*
sharpness.
adjust sharpness in
screen
Transmission
in the Picture
Transmission
Data
also
can
mapping'
as
shown below.
Acknowledgement
mapping'
as
shown below.
[Set ID][:][OK][x][Data][x]
Data
Min:0~Max:64
[Set ID][:][OK][x][Data][x]
*
Data
Min:0~Max:64
Real data
0
mapping
:Step0
A:Step10
Others
F:Step15
10:Step16
64
:
Step
FirstepMonvwCcBaSlmPu&df
100
51
External Control Device
13. Abnormal state
Γ To recognize
an
(Command:a)
abnormal state.
14. PIP
Transmission
also control PIP with
0
:OK
1
:
2
:5Vdown
3
:ACdown
in the
button
on
the
[z][ ][Set ID][ ][Data][Cr]
Data
Fan alarm
0
:PIPoff
1
:
PIP
2
:
PIP
(small)
(large)
Acknowledgement
This function is "read
[Set ID][:][OK][x][Data][x]
only".
Data
12. OSD select
or
.
using PIP
special menu.
Transmission
[Set ID][:][OK][x][Data][x]
*
can
remote control
Acknowledgement
Data
(Command:z)
Γ To control PIP(Picture In Picture)
You
[a][ ][Set ID][ ][FF][Cr]
Setup
(Command:d)
*
PIP
0
:PIPoff
1
:
PIP
2
:
PIP
(small)
(large)
following resolutions:
640x480(VGA) / 800x600(SVGA) /
1024x768(XGA) (only in vertical frequency 60Hz),
Component 480p.
only
works in the
RGB PC
Γ To select OSD (On Screen Display) on/off.
Transmission
[d][ ][Set ID][ ][Data][Cr]
Data
0
:OSDoff
1
:OSDon
15. PIP
Γ To select input
Acknowledgement
You
[Set ID][:][OK][x][Data][x]
Data
*
0
:OSDoff
1
:OSDon
main
power)
can
select
source
also select
the remote control
(Command:e)
for sub
picture in PIP mode.
using PIP input button on
the Special menu.
source
or
in
Transmission
The remote control and Monitor front
(except
input
are
is set up to be controlled
not
by
panel controls
operable when the Monitor
[e][ ][Set ID][ ][Data][Cr]
Data
the PC.
0
:
AV
1
:
COMPONENT
2
:
S-AV
(VIDEO)
(S-VIDEO)
Ack
[Set ID][:][OK][x][Data][x]
Data
*
52
0
:
AV
1
:
COMPONENT
2
:
S-AV
(VIDEO)
(S-VIDEO)
COMPONENT
source
only
works with 480i
input signal.
16. PIP sound select
(Command:u)
18.
Change
into Remote control
ment mode
Γ To select main
You
can
special
or
sub
(inset)
sound for PIP.
also select sound select in PIP
on
the
menu.
:
1
:
Main
Sub
[j][ ][Set ID][ ][Data][Cr]
picture sound
picture sound
Data
Acknowledgement
*
0
:
Main
1
:
Sub
source
:
Remote control
adjustment
mode
[Set ID][:][OK][x][Data][x]
picture sound
picture sound
COMPONENT
1
Acknowledgement
[Set ID][:][OK][x][Data][x]
Data
To control the Monitor with the remote control while
Transmission
[u][ ][Set ID][ ][Data][Cr]
0
Γ
the cable is still connected.
Transmission
Data
adjust-
(Command:j)
only
Data
works in 480i
input signal.
*
0
:
PC
1
:
Remote control
If external
"change
Monitor
adjustment
equipment
mode
adjustment
mode
commands the Monitor to
into remote control
can
only
be
adjustment mode", the
adjusted by the remote control.
To revert the Monitor control to external control device
adjustment,
17. PIP
turn the Monitor off and then
on
again.
position (Command:x)
Γ To select sub picture position for PIP.
You
can also adjust the sub picture position using the
position button on the remote control or in PIP on the
Special menu.
Transmission
[x][ ][Set ID][ ][Data][Cr]
Data
down
0
:
Right
1
:
Left down
2
:
Left up
3
:
Right
on screen
on screen
on screen
up
on screen
Ack
[Set ID][:][OK][x][Data][x]
Data
down
0
:
Right
1
:
Left down
2
:
Left up
3
:
Right
on screen
on screen
on screen
up
on screen
FirstepMonvwCcBaSlmPu&df
Others
53
check list
Troubleshooting
No
picture
&
?
Check whether the Monitor is turned
?
Power cord inserted into wall outlet?
on.
No sound
?
?
Press the VOLUME
?
Sound muted? Press MUTE button.
Picture OK &
No sound
?
The remote control
?
doesn't work
?
or
or
Poor colour
Poor
picture
Check to
Install
output from one
of the speakers
Strange
sound
from the Monitor
54
button.
if the batteries
(Refer to p.30)
see
new
batteries.
(Refer
are
to
Select Colour in the Picture
(Γ) button. (Refer to p.36)
installed with the correct
p.30)
menu
and press the VOLUME
certain distance between the Monitor and the VCR.
?
Keep
?
Activate any function to restore the brightness of the picture.
(If still picture is on the screen for more than 5 minutes, the
a
screen
No
(Γ)
Check to see if there is any object between the Plasma
Display and the remote control causing obstruction.
polarities.
?
No
Plug another product's power cord into the wall outlet where
the Monitor's power cord was plugged in.
?
Adjust
?
Typical
faulty.
gets dark.)
Balance in the Sound
menu.
sound due to normal Monitor
(Refer
to
operation,
p.39)
Monitor is not
Product
specifications
MT-42PZ15/A/B/G/K/S
MODEL
Width
(inches
/
mm)
41.6 / 1056
Height (inches
/
mm)
25/635
Depth (inches
/
mm)
3.2/82
Weight (pounds
Power
/
72.1 / 32.7
kg)
110-240V~50/60Hz
requirement
852
Resolution
Colour
?
The
specifications
improvement.
x
480
(Dot)
16,770,000 (256 steps of each R, G and B)
shown above may be
changed
without notice for
quality
FirstepMonvwCcBaSlmPu&df
Others
55
Download PDF

advertising