LG | RT-23LZ55 | LG RT-23LZ55 Owner’s Manual

LCD TV
OWNER'S MANUAL
MODEL: RT-23LZ55***
Please read Information Manual included together
before reading this manual and operating your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached
and quote
this information to your dealer when you require service.
on
the back
P/NO
:
cover
3828TUL330G
(0506-REV00)
Printed in Korea
Contents
Installation
3
Location and function of controls
Remote control handset
Battery installation / Front / Rear
4
Basic operation
On and off / Programme selection
Volume adjustment / Quick view
Mute function
On screen language selection
8
On
9
screen menus
Menu selection
10
up TV stations
Auto programme tuning
Manual programme tuning
Setting
Programme
edit
Favourite programme
Calling the programme table
Picture adjustment
PSM (Picture Status
Picture adjustment
Picture format
15
Memory)
Sound
17
Time Menu
Clock / On/Off time
Auto off / Sleep timer
19
Other functions
21
adjustment
SSM (Sound Status Memory)
Sound adjustment / Stereo/Dual reception
NICAM reception / Sound output selection
TV, AV and PC modes
Child lock
Teletext (option)
Switch on/off
SIMPLE text / TOP text (option)
FASTEXT / Special teletext functions
23
Connection of external
26
equipment
Aerial socket
Audio/Video in sockets
S-Video/Audio in sockets
DVD input sockets
DTV in sockets
(S-Video)
Connection of PC
PC in socket
PC Setup (only
28
DVI-Analogue mode)
External Control Device
Setup
IR Codes
Troubleshooting
2
; RS-232C
(option)
30
34
check list
36
Installation
Connection of TV
12
Pull the back
cover
backside while
pushing
the two tabs and then lift it up.
Connect the aerial cable to the socket marked +75 Ω
on
the back. For the best
reception
an
outdoor aerial should be used.
To connect
345
an
additional
equipment,
see
the Connection of external
equipment
section.
Connect the power cord.
Close the back
cover.
1
24
~
5
Positioning your display
-
Thread, then pull the cables (except the aerial cable) through the hole
aerial cable
through
the side hole
as
on
the TV stand.
Arrange
the
shown below.
Aerial cable
Positioning your display
Adjust
?
the
position
of the
panel
in various ways for maximum comfort.
Tilt range
5
15
3
Location and function of controls
All the functions
can
be controlled with the remote control handset.
Some functions
can
also be
of the set.
ate this set.
Only
panel
with the buttons
adjusted
the remote control handset
on
supplied
the side
will oper-
Remote control handset
10
MUTE
POWER
1
11
TV/AV MULTIMEDIA
12
1.
Q.VIEW MENU
2.
PR
OK
VOL
VOL
PR
3.
123
6
on or
off.
TV/AV p.21
selects TV or AV monitor mode.
clears the menu from the screen.
switches the set on from standby.
selects: TV, AV, S-Video, COMPONENT1, COMPONENT2
PC mode.
-
LIST
p.14
displays the
789
-
SSM
0
SLEEP
ARC
PSM
selects
14
5.
TEXT
15
UPDATE
TIME
SIZE
MIX
HOLD
REVEAL
INDEX
i
Q.VIEW
-
returns to
D / E
a
programme table.
p.14
the previously
viewed programme.
favourite programme.
(Programme Up/Down)
selects
programme or a menu item.
switches the set on from standby.
a
F / G
(Volume Down/up)
adjusts the volume.
adjusts menu settings.
?
OK
MODE
M
accepts your selection
6.
SSM
8.
ARC
the current mode.
displays
standby
Status
and selects
a
programme.
(Sound
Memory) p.17
recalls your preferred sound setting.
-
-
p.16
select your desired
9.
or
NUMBER BUTTONS
switches the set on from
7.
(With TELETEXT)
SLEEP
sets the
p.20
sleep
picture
format.
-
timer.
10. MULTIMEDIA
selects: TV, COMPONENT1, COMPONENT2
4
or
456
4.
789
MUTE
switches the sound
13
34
5
handset, please install the bat-
I/II
2
LIST
Before you use the remote control
teries. See the next page.
or
PC mode.
Location and function of controls
11. POWER
switches the set
on
from
standby
12. I/II p.18
selects the language during dual
selects the sound output.
or
off to
standby.
-
language
broadcast.
13. MENU
selects
10
a menu.
MUTE
14. PSM (Picture Status
recalls your preferred
1
Memory) p.15
picture setting.
11
-
TV/AV MULTIMEDIA
15. TELETEXT BUTTONS (option) p.23~25
These buttons are used for teletext.
For further details, see the 'Teletext' section.
-
:
12
TELETEXT
models)
or
These buttons
are
13
PR
5
:
Q.VIEW MENU
34
No function
COLOURED BUTTONS
I/II
2
LIST
*
POWER
used for teletext
OK
VOL
VOL
PR
(only
programme edit.
123
Battery
installation
6
456
789
The remote control handset is powered by two AAA/Alkaline type batteries. To load the batteries, turn
the
remote
control
handset
over
SSM
789
SLEEP
0
PSM
14
ARC
and open the battery compartment.
Install two batteries as indicated by
the
polarity symbols (
marked inside the
+
and
-
)
compartment.
Note : To avoid damage from possible battery leakage, remove the
batteries if you do not plan to use the remote control handset for an
extended period of time.
(Without TELETEXT)
5
Location and function of controls
Front
Side
panel
PR
6
VOL
5
OK
4
MENU
3
TV
AV/PC
2
1
1.
ON/OFF(
8
7
9
6.
/I)
switches the set
on
from
standby
or
TV/AV/PC
selects
TV, AV
clears the
or
menu
switches the set
3.
programme or a menu item.
switches the set on from standby.
4.
from the
on
from
screen.
8.
POWER ON/STANDBY INDICATOR
illuminates red in standby mode.
standby.
a menu.
9.
OK
or
displays
F / G
(Volume Down/Up)
adjusts the volume.
adjusts menu settings.
( )
illuminates green when the set is switched
on.
mode.
6
REMOTE CONTROL SENSOR
PC monitor mode.
accepts your selection
5.
a
7.
MENU
selects
(Programme Up/Down)
selects
off to
standby.
2.
D / E
the current
Stand
(option)
Location and function of controls
Rear
S-VIDEO INPUT
COMPONENT 2 IN
(480i/576i)
AUDIO INPUT
1
PC SOUND INPUT
DVI INPUT
(RGB INPUT)
UPGRADE PORT
AUDIO/VIDEO
ANTENNA
INPUT
INPUT
COMPONENT1
REMOTE CONTROL
(DVD/DTV IN)
((480i/480p/576i/576p/720p/1080i), Audio)
JACK
AC INPUT
7
Basic
operation
On and off
1.
Press the
2.
buttons to switch it on fully.
Press the POWER button. The set reverts to
3.
Pull out mains
Note
:
POWER,
If, while the
plugs
E, TV/AV, MULTIMEDIA
or
NUMBER
standby
mode.
to switch the set off.
set is switched on, the mains
the set will switch to
replaced
D /
standby
or
power
in the mains power socket.
on
plug is
disconnected
when the mains
plug
is
MUTE
POWER
TV/AV MULTIMEDIA
Programme
I/II
selection
Q.VIEW MENU
You
can
select
programme number with the D / E
a
or
NUMBER
buttons.
PR
Volume
adjustment
Press the F / G button to
OK
VOL
adjust
VOL
the volume.
PR
Quick view
123
Press the Q.VIEW button to view the last programme you
were
watching.
456
Note : This function works only when Favourite programme is set
to Off. Otherwise each press of this button will select a stored
favorite programme.
789
SSM
Mute function
Press the MUTE button. The sound is switched off and the
display
appears.
You can cancel it
button.
On
screen
The
menu can
First select
1.
3.
language
be
the
MUTE,
F /
G, I/II,orSSM
selection
displayed
your language.
on
the
screen
in your desired
Press the MENU button and then D / E
Setup
2.
by pressing
language.
button to select the
menu.
Press the G button and then D / E button to select Language.
Press the G button and then D / E button to select your desired
language.
All the
on screen
displays
will appear in the selected
4.
Press the OK button.
5.
Press the TV/AV button to return to normal TV
8
language.
viewing.
0
On
screen menus
Menu selection
2.
Press the MENU button and then D / E button to display each menu.
Press the G button and then D / E button to select a menu item.
3.
Change
1.
the
setting
of
an
item in the sub
or
pull-down
menu
with
F / G button.
You
can move
button and to
to the
higher
level
move
to the lower level
menu
by pressing the OK
menu by pressing the
MENU button.
Note :
In the TV/AV, COMPONENT mode, the PC
a.
menu
is not dis-
played.
MENU
b.
In the teletext
c.
On
some
mode, menus are not displayed.
models, the Language will not be displayed.
Picture
Channel
PR
OK
VOL
VOL
Auto programme
PSM
Manual programme
Contrast
Programme edit
Brightness
Favourite programme
Colour
Sharpness
PR
DEFG
OK
DEFG
MENU
Channel
OK
MENU
Picture
menu
menu
Sound
Setup
SSM
Language
AVL
Input
Balance
Child lock
DEFG
OK
MENU
Setup
DEFG
OK
MENU
Sound
menu
menu
Time
Time
Off time
On time
Auto off
DEFG
OK
MENU
Time
menu
9
Setting
programme numbers (0 to 99).
Once you have preset the stations, you will be able to use the D / E
or NUMBER buttons to scan the stations you have programmed.
Stations can be tuned using automatic or manual modes.
Up to
100 TV stations
can
Auto programme
be stored
TV
stations
up
by
2.
Auto programme
Manual programme
Programme edit
Favourite programme
tuning
All stations that can be received are stored by this method.
It is recommended that you use auto programme during installation of
this set.
1.
Channel
DEFG
OK
MENU
Press the MENU button and then D / E button to select the
Channel menu.
Press the G button and then D / E button to select Auto
programme.
Auto programme
BG
System
Storage from
Search
TV/AV
IDK
L
MENU
M
DEFG
3.
4.
5.
6.
7.
OK
MENU
Press the G button. Select a TV system with the G button and
then D / E button on the System menu;
BG : PAL B/G, SECAM B/G (Europe/East Europe)
I
: PAL I/II (U.K./Ireland)
DK : PAL D/K, SECAM D/K (East Europe)
L
: SECAM L/L' (France)
M
: (USA/Korea/Philippines)
Press the OK button.
Press the D / E button to select Storage from.
Select the beginning programme number with the F / G button
or NUMBER buttons on the Storage from pull-down menu. Any
number under 10 is entered with a numeric '0' in front of it, i.e.
'05' for 5.
Press the D / E button to select Search.
Auto programme
Search
C21
2
BG
5%
MENU
Press the G button to
All receivable stations
begin
are
auto
programming.
stored.
In Australia, if no station name can be assigned to a
folstation, the channel number is assigned and stored as
lowed by a number see 'Assigning a station name' section to
assign the station name.
Option:
-----
To stop auto programming, press the MENU button.
When auto programming is completed, the Programme edit
menu appears on the screen. See the 'Programme edit' section
to edit the stored programme.
9.
10
OK
VOL
VOL
PR
123
456
789
0
System
Storage from
8.
PR
Press the TV/AV button to return to normal TV
viewing.
TV
stations
up
Setting
Manual programme
Channel
tuning
Auto programme
Manual programme
Programme
Manual programme lets you manually tune and arrange the stations in whatever order you desire. Also you can assign a station
name with five characters to each programme number.
edit
Favourite programme
DEFG
OK
1.
Press the MENU button and then D / E button to select the
Channel menu.
2.
Press the G button and then D / E button to select Manual
3.
programme.
Press the G button and then D / E button to select
MENU
Storage.
Manual programme
29
Storage
System
Channel
TV/AV
Search
Name
MENU
DEFG
4.
PR
5.
OK
VOL
VOL
6.
PR
123
456
789
OK
MENU
Select the desired programme number (0 to
button or NUMBER buttons on the Storage
with the F / G
menu. Any number
99)
under 10 is entered with a numeric '0' in front of it, i.e. '05' for 5.
Press the D / E button to select System.
Select a TV system with the G button and then F / G button on
the System menu;
BG
:
PAL
I
:
PAL I/II
DK
L
:
PAL D/K, SECAM D/K
SECAM L/L' (France)
M
:
:
B/G, SECAM B/G (Europe/East Europe)
(U.K./Ireland)
(East Europe)
(USA/Korea/Philippines)
7.
Press the OK button.
8.
Press the D / E button to select Channel.
Press the G button and then D / E button to select VHF/UHF
Cable on the Channel menu.
9.
If
0
possible, select the channel number directly
buttons. Any number under 10 is entered with
front of
or
with the number
a
numeric '0'
in
it, i.e. '05' for 5.
10. Press the OK button.
11. Press the D / E button to select Search.
12. Press the G button and thenF / G button to
on
the Search
pull-down
menu.
If
a
commence
searching
station is found the search will
stop.
Manual programme
Storage
System
Channel
Search
GGG
Name
DEFG
OK
MENU
13. Press the OK button to store it.
14. To store another
station, repeat steps 3
to 13.
15. Press the TV/AV button to return to normal TV
viewing.
11
Setting
TV
stations
up
Assigning a station name
1.
Repeat the 'Manual programme tuning' steps
Channel
1 to 2.
Auto programme
3.
Press the G button and then D / E button to select Name.
Press the G button and then use the D / E. You can use a blank,
4.
-,thenumber0to9andthealphabetAtoZ.
With the F button you can select in the opposite direction.
Select the position by pressing the F / G button and then
5.
your choice of the second character, and
Press the OK button to store it.
6.
Press the TV/AV button to return to normal TV
2.
Manual programme
Programme edit
Favourite programme
+,
make
DEFG
OK
MENU
so on.
viewing.
TV/AV
MENU
PR
OK
VOL
VOL
PR
12
TV
stations
up
Setting
Channel
Programme
Auto programme
Manual programme
This function enables you to delete or skip the stored programmes.
Also you can move some stations to other programme numbers or
insert a blank station data into the selected programme number.
Programme edit
Favourite programme
DEFG
OK
edit
1.
Press the MENU button and then D / E button to select the
Channel menu.
2.
Press the G button and then D / E button to select
edit.
3.
Press the G button to
MENU
Programme edit
the
display
0C035S
Programme
Menu.
69
1BLN03
6S17
2C1 2
7-----
3S66
8-----
4S67
9-----
TV/AV
Delete
Copy
Move
Skip
MENU
Deleting
1.
programme
Select a programme to be deleted with the D / E
2.
Press the RED button twice.
The selected programme is
programmes are shifted up
PR
OK
VOL
a
F / G button.
or
deleted, all the following
one
position.
VOL
0C0 35S
PR
69
1BLN03
6S17
2C1 2
7-----
3S6 6
8-----
4S6 7
9-----
123
Delete
456
Copying
789
a
1.
programme
Select a programme to be
2.
Press the GREEN button.
All the
0
Moving
following
copied
with the D / E
are
programmes
shifted down
or
F / G button.
one
position.
a
1.
programme
Select a programme to be moved with the D / E
2.
Press the YELLOW button.
3.
Move the programme to the desired programme number with
or
F / G button.
theD/EorF/Gbutton.
4.
Press the YELLOW button
Skipping
1.
Select
a
a
again
programme number
programme number to be
to release this function.
skipped
with the D / E
or
F / G
button.
2.
3.
Press the BLUE button. The
programme turns to blue.
Press the BLUE button again to release the skipped programme.
When a programme number is skipped it means that you will be
unable to select it using the D / E button during normal TV
viewing. If you want to select the skipped programme, directly
enter the programme number with the NUMBER buttons or
select it in the programme edit or table menu.
skipped
Press the TV/AV button to return to normal TV
viewing.
13
Setting
TV
stations
up
Favourite programme
Channel
This function lets you select your favourite programmes
Auto programme
directly.
1.
Press the MENU button and then D / E button to select the
Channel menu.
2.
Press the G button and then D / E to select Favourite
Manual programme
Programme edit
Favourite programme
programme.
DEFG
OK
MENU
Favourite programme
On
--
-----
--
-----
--
-----
--
-----
--
-----
--
-----
--
-----
--
-----
DEFG
OK
MENU
3.
Press the G button and then F / G button to select On or Off.
4.
Press the D / E button to select
-----.
Select a desired programme with the F / G button.
To store another programme, repeat steps 4 to 5.
You can store up to 8 programmes.
Press the TV/AV button to return to normal TV viewing.
5.
6.
7.
TV/AV
--
Repeatedly press
LIST
the Q.VIEW button to select stored favourite
Q.VIEW MENU
PR
programmes.
OK
Calling
You
the programme table
VOL
check the programmes stored in the memory
the programme table.
can
Displaying programme
table
Press the LIST button to
display
the
by displaying
Programme table
menu.
The programme table appears on the screen. One programme
table contains ten programmes as below.
0C0 35S
6S17
2C12
7S22
3S66
8C09
4S67
9C11
Select
a
programme in the programme table
programme with the D / E
Then press the OK button.
a
or
F / G button.
The set switches to the chosen programme number.
Paging through
There
are
a
programme table
10 programme table pages in which contain 100
programmes.
Pressing the D / E
or
F / G button
repeatedly
Press the TV/AV button to return to normal TV
14
123
456
0
Note :
a.
You may find some blue programmes. They have been set up to
be skipped by auto programming or in the programme edit mode.
b. Some programmes with the channel number shown in the
programme table indicate there is no station name assigned.
Selecting
PR
789
69
1BLN03
VOL
turns the pages.
viewing.
Picture
PSM
Picture
PSM
Contrast
Sharpness
(Picture Status Memory)
1.
Press the MENU button and then D / E
Picture menu.
2.
Press the G button and then D / E button to select PSM.
Press the G button and then D / E button to select a picture
Brightness
Colour
3.
setting
DEFG
OK
4.
MENU
adjustment
on
the PSM
button to select the
menu.
Press the OK button.
Picture
PSM
Dynamic
Contrast
Standard
Brightness
Mild
Colour
Game
Sharpness
User
DEFG
TV/AV
5.
MENU
OK
MENU
Press the TV/AV button to return to normal TV
viewing.
picture (Dynamic, Standard, Mild,
Game or User) with PSM button on the remote control. The picture
Dynamic, Standard, Mild and Game are programmed for optimum
picture reproduction at the factory and cannot be changed.
You
also recall
can
a
desired
PR
Picture
OK
VOL
VOL
You
can
and tint
PR
1.
adjustment
adjust picture contrast, brightness,
colour
to the levels you
prefer.
(NTSC input only)
Press the MENU button and then D / E
Picture menu.
intensity, sharpness
button to select the
Picture
PSM
Contrast
47
Contrast
Brightness
Colour
Sharpness
PSM
DEFG
2.
3.
OK
MENU
Press the D / E button to select the desired
Press the F / G button to make appropriate
it will be stored for the
4.
picture
picture item.
adjustments,
User.
Press the TV/AV button to return to normal TV
Note
:
Only
Contrast and
then
Brightness
are
viewing.
displayed
in PC mode.
15
Picture
adjustment
Picture format
You
watch TV in various
can
picture formats; 16:9, 14:9, Zoom,
Auto, 4:3.
Repeatedly
press the ARC button to select your desired
picture
format.
16:9
You
enjoy the cinema (the picture format of 16:9) or general
programme through the 16:9 mode.
The screen 16:9 is viewed just like that but the screen 4:3 is
magnified to the left and right so that the screen 16:9 is full.
can
TV
14:9
You
can
through
The
the picture format of 14:9
the 14:9 mode.
enjoy
screen
14:9 is viewed
to the upper / lower and
just like
left / right.
or
that the
TV programme
general
screen
4:3 is
TV/AV
magnified
MENU
Zoom
You
The
so
the cinema in a vast screen through the Zoom mode.
screen 4:3 is magnified to the upper / lower and left / right sides
that the screen 16:9 is full. The bottom and top of the picture
can
enjoy
may be lost.
PR
OK
VOL
VOL
PR
Auto
When your set receives the wide screen signal, it will be automatically
changed to the picture format to be sent.(Not available in all countries)
4:3
This
picture
Note
:
format is 4 to 3 of
In PC mode
only
general
16:9 and 4:3
TV.
aspect ratios
are
available.
ARC
16
Sound
Sound
SSM
(Sound Status Memory)
SSM
AVL
You
Balance
Speech
1.
adjustment
select your preferred sound setting; Flat, Music, Movie or
and you can also adjust the sound frequency of the equalizer.
can
Press the MENU button and then D / E button to select the
Sound menu.
Sound
DEFG
OK
SSM
Flat
AVL
Music
Balance
Movie
MENU
Speech
G
User
DEFG
2.
3.
TV/AV
OK
MENU
Press the G button and then D / E button to select SSM.
Press the G button and then D / E button to select a sound
setting on the SSM menu.
Sound
Frequency Adjustment
Press the OK button in User.
b. Select a sound band by pressing the F / G button.
c. Make appropriate sound level with the D / E button.
d. Press the OK button to store it for the sound User.
MENU
a.
PR
OK
VOL
VOL
PR
0.1
0.5
1.5
10Khz
5
Press the TV/AV button to return to normal TV
You
viewing.
also recall a desired sound setting (Flat, Music, Movie, Speech
or User) with SSM button on the remote control. The sound settings
Flat, Music, Movie and Speech are programmed for optimum sound
reproduction at the factory and cannot be changed.
can
If you press the SSM button after making appropriate
adjustment on the User sub menu, the display User automatically
appears even though you have already set a factory preset setting;
Flat, Music, Movie or Speech.
Note
SSM
:
Sound
SSM
On
Balance
Off
DEFG
AVL
Sound
You
AVL
OK
MENU
adjustment
adjust balance, AVL (Auto Volume Leveler).
automatically keeps on an equal volume level
change programmes.
1.
2.
3.
can
even
if you
Press the MENU button and then D / E button to select the
Sound menu.
Press the G button and then D / E button to select the desired
sound item; AVL or Balance.
Make desired adjustment with the F / G, D / E and then press
the OK button.
4.
Press the TV/AV button to return to normal TV
viewing.
17
Sound
Stereo/Dual
When
adjustment
reception
programme is selected, the sound information for the station appears after the programme number and station name disappear.
a
Broadcast
On Screen
Mono
MONO
Stereo
STEREO
Dual
DUAL I
Display
Mono sound selection
In stereo reception if the stereo signal is weak, you can switch to
mono by pressing the I/II button twice. In mono reception the depth
of sound is improved. To switch back to stereo, press the I/II button twice again.
selection for dual language broadcast
programme is received in two languages (dual language), you
switch to DUAL I, DUAL II or DUAL I+II by pressing the I/II but-
Language
If
a
can
ton
repeatedly.
DUAL I sends the
primary broadcast language to the loudspeakers.
the secondary broadcast language to the loud-
DUAL II sends
speakers.
DUAL I+II sends
NICAM
a
separate language
to each
loudspeaker.
reception
If your set is
equipped
with the receiver for NICAM
reception, the
Companding Audio
high quality NICAM (Near Instantaneous
Multiplex) digital sound can be received.
Sound output can be selected according to the type of received
broadcast as follows by pressing the I/II button repeatedly.
1.
When NICAM
or
2.
is
received, you
can
select NICAM MONO
FM MONO.
When
NICAM
STEREO
3.
mono
or
stereo
received, you
FM MONO. If the stereo
FM mono.
When NICAM dual is
NICAM DUAL II
mono
is
or
is selected the
can
signal
is
select
NICAM
weak, switch
to
select NICAM DUAL I,
NICAM DUAL I+II or MONO. When FM
received, you
can
MONO appears
display
on
the
screen.
Sound output selection
In AV
mode, you
can
select
output sound for the left and right loud-
speakers.
press the I/II button to select the sound output.
Audio signal from audio L input is sent to left loud-speaker
and audio signal from audio R input is sent to right loud-
Repeatedly
L+R
L+L
18
:
:
speaker.
Audio signal
speakers.
from audio L
input
is sent to left and
right
loud-
I/II
TIME Menu
Clock
Time
Time
You must set the time
Off time
correctly
before
using
on/off time function.
On time
Auto off
1.
Press the MENU button and then D / E
TIME
2.
DEFG
OK
button to select the
menu.
Press the G
button and then D / E button to select TIME.
Time
MENU
-i-i:i-i-
Time
Off time
On time
Auto off
DEFG
OK
MENU
3.
Press the G
4.
Press the G button and then D / E button to
5.
Press the MENU button to
button and then D / E button to
adjust the hour.
adjust the minute.
save.
MENU
On/Off Time
The off timer
1.
OK
Press the MENU button and then D / E
TIME
VOL
PR
switches the set to
standby
at the
preset time.
PR
VOL
automatically
button to select the
menu.
2.
Press the G button and then D / E button to select Off Time
On Time.
3.
Press the G
or
button and then D / E button to select On.
To cancel Off/On Time function, press the D / E button to
select Off.
Time
Time
Off time
On time
-i-i:i-i-
Auto off
Pr.
Vol.
0
30
On
DEFG
OK
MENU
Press the G
5.
button and then D / E button to adjust the hour.
Press the G button and then D / E button to adjust the minute.
6.
Only
4.
On Time
button to
7.
function;
Press the G
volume level and programe number.
Press the MENU button to save.
Note
adjust
:
a.
In the event of power interruption
failure), the clock must be reset.
b.
Two hours after the set is switched
will
automatically switch back
has been pressed.
c.
d.
to
(disconnection
or
power
by the on time function it
standby mode unless a button
on
Once the on or off time is set, these functions operate daily at
the preset time.
Off Timer function overrides On Timer function if they are set to
the
e.
button and then D / E
same
time.
The set must be in
standby mode for the On Timer
to work.
19
TIME Menu
Time
Auto off
Time
Off time
If you select On on the Auto Off menu, the set will automatically
switch itself to standby mode approximately ten minutes after a TV
station stops broadcasting.
On time
Auto off
DEFG
OK
MENU
1.
Press the MENU button and then D
TIME menu.
2.
Press the G button and then D
Press the G button and then D
3.
/ E
button to select the
/ E
button to select Auto Off.
/ E
button to select On
or
Off.
Time
Time
Off time
On time
On
Auto off
Off
DEFG
MENU
4.
OK
VOL
VOL
PR
MENU
Press the MENU button to
Sleep
PR
OK
save.
timer
You don't have to remember to switch the set off before you go to
sleep. The sleep timer automatically switches the set to standby
after the
preset time has elapsed.
Press the SLEEP button to select the number of minutes.
The display
Off' will appear on the screen, followed by 10, 20,
30, 60, 90, 120, 180 and 240. The timer begins to count down from
'
the number of minutes selected.
Note :
a.
To view the
remaining sleep time,
press the SLEEP button
once.
b.
To cancel the sleep time, repeatedly press the SLEEP button
Off' appears.
until the display
When you switch the set off, the set releases the preset sleep
time.
'
c.
SLEEP
20
Other functions
TV,
Setup
Language
AV and PC modes
be set for
TV, AV
Input
Inputs
Child lock
video cassette recorder
can
or
(VCR),
PC mode. AV mode is used when
or
other
a
is connected to
equipment
the set.
DEFG
OK
Note : When a VCR is connected via the aerial socket the set is
used in TV mode. See the 'Connection of external equipment' section.
MENU
1.
Press the MENU button and then D / E button to select the
Setup
2.
3.
menu.
Press the G button and then D / E button to select Input.
Press the G button and then D / E button to select TV, AV,
S-Video, Component 1, Component 2 or PC.
The AV and PC modes
TV/AV
are :
Setup
Language
MENU
Input
TV
Child lock
AV
S-video
Component
1
Component
2
PC
PR
DEFG
OK
VOL
AV
VOL
MENU
VCR connected to the AV socket of the set.
:
S-Video
PR
OK
VCR connected to the S-Video of the set.
:
Component
1
DVD/DTV connected to the DVD/DTV IN
:
sockets of the set.
Component
123
:
DVD connected to the DVD IN sockets
on
the
back of set.
PC
456
:
PERSONAL COMPUTER connected to the PC socket
of the set.
4.
789
2
Press the TV/AV button to return to normal TV
Alternatively
you
TV/AV button.
can
select the TV
or
AV mode
viewing.
by pressing
the
0
In AV
mode,
to return to TV
mode, press the
D / E
or
NUMBER
buttons.
21
Other functions
Child lock
The TV
can
Setup
be set
so
Language
that the remote control handset is needed to
control it. This feature
can
be used to
prevent
Input
unauthorized view-
Child lock
ing.
1.
Press the MENU button and then D / E button to select the
Setup
2.
3.
DEFG
OK
MENU
menu.
Press the G button and then D / E button to select Child lock.
Press the G button and then D / E button to select On or Off
on the Child lock menu.
Setup
Language
Input
Child lock
On
Off
TV/AV MULTIMEDIA
MENU
DEFG
4.
OK
MENU
Press the TV/AV button to return to normal TV
viewing.
With the lock on, the display Child lock appears on the screen if
any button on the side panel is pressed while viewing the TV.
Note : The display Child lock will not appear on the screen if any
button on the side panel is pressed while displaying the menus.
22
PR
OK
VOL
VOL
PR
Teletext
Teletext
(or
(option)
TOP
with the teletext
Teletext is
a
text)
is
system
an
can
optional function,
therefore
free service broadcast
The teletext decoder of this TV
by
can
by directly entering
TOP and FASTEXT
set
most TV stations which
are more
television
support the SIMPLE, TOP and
FASTEXT systems.
SIMPLE (standard teletext) consists of
selected
a
receive the teletext broadcast.
gives up-to-the-minute information on news, weather,
programmes, share prices and many other topics.
are
only
number of pages which
the corresponding page number.
a
modern methods
allowing quick
and
easy selection of teletext information.
Switch on/off
Press the TEXT button to switch to teletext. The initial page
page appears on the screen.
PR
or
last
Two page numbers, TV station name, date and time are displayed on
the screen headline. The first page number indicates your selection,
while the second shows the current page displayed.
OK
Press the TEXT button to switch off teletext. The
PR
previous
mode
reappears.
123
SIMPLE text
selection
Enter the desired page number as a three digit number with
the NUMBER buttons. If during selection you press a wrong
number, you must complete the three digit number and then
re-enter the correct page number.
The D / E button can be used to select the preceding or following
Page
456
1.
789
0
2.
page.
TEXT
colour button in LIST mode
If the TV is in SIMPLE text, TOP text or FASTEXT mode, press the
M button to switch to LIST mode.
Programming
MODE
M
a
Four teletext page numbers of your choice can be colour coded and
easily selected by pressing the corresponding coloured button on
the remote control handset.
1.
Press
a
2.
Using
the NUMBER
3.
4.
coloured button.
buttons, select the page you wish
to
programme.
Press the OK button. Then the selected page is stored as the
selected page number by blinking once. From now on, you can
select this page with the same coloured button.
The three other coloured buttons are programmed in this way.
23
Teletext
TOP text
The
user
(option)
(option)
guide displays
the bottom of the
four
fields-red, green, yellow and blue
field denotes the next group
and the blue field indicates the next block.
screen.
The
at
yellow
Block / group / page selection
1. With the blue button you can progress from block to block.
2. Use the yellow button to proceed to the next group with
automatic overflow to the next block.
3. With the green button you can proceed to the next existing
page with automatic overflow to the next group.
Alternatively the D button can be used.
4. The red button permits to return to previous selection.
Alternatively the E button can be used.
Direct page selection
Corresponding to the SIMPLE teletext mode, you can select a page
by entering it as a three digit number using the NUMBER buttons in
TOP mode.
PR
OK
FASTEXT
The teletext pages are colour coded along the bottom of the screen
and are selected by pressing the corresponding coloured button.
selection
i button to select the index page.
Press the
You can select the pages which are colour coded along the
bottom line with the same coloured buttons.
Corresponding to the SIMPLE teletext mode, you can select a
page by entering its three digit page number with the NUMBER
buttons in FASTEXT mode.
The D / E button can be used to select the preceding or following
PR
123
Page
1.
2.
3.
4.
456
789
0
page.
INDEX
i
24
M
Teletext
Special
?
(option)
teletext functions
REVEAL
Press this button to
display concealed information, such as
solutions of riddles or puzzles.
Press this button again to remove the information from the
display.
SIZE
Selects double
Press
Press
height text.
this button to enlarge the top
this button again to enlarge
page.
Press this button
again
half of the page.
the bottom half of the
to return to the normal
display.
PR
UPDATE
Displays
the TV
picture on
The display
the
screen
while
waiting
for the
new
teletext page.
will appear at the top left hand
corner of the screen. When the updated page is available then
will change to the page number.
display
Press this button to view the updated teletext page.
PR
123
HOLD
the automatic page change which will occur if a teletext
page consists of 2 or more sub pages. The number of sub
pages and the sub page displayed is, usually, shown on the
Stops
below the time. When this button is
screen
is
symbol
displayed
at the
top left-hand
pressed
corner
the
of the
456
789
stop
screen
0
and the automatic page change is inhibited.
To continue press this button again.
MIX
the teletext pages superimposed on the TV
To switch the TV picture off press this button again.
Displays
picture.
TIME
UPDATE
TIME
SIZE
MIX
HOLD
REVEAL
?
When
viewing
TV programme, press this button to display
the time at the top right hand corner of the screen. Press this
button
again
a
to
remove
the
display.
In the teletext
mode,
press this button to select a sub page number. The sub page
number is displayed at the bottom of the screen. To hold or
the sub page, press the
NUMBER buttons.
change
Press
again
RED/GREEN,
D
/ E
or
to exit this function.
25
Connection of external
You
can
connect additional
etc. to your set.
Examples
equipment,
are
such
as
equipment
VCRs, camcorders
shown below.
Aerial socket
1.
Connect the RF out socket of the VCR to the aerial socket of
1
the set.
2.
Connect the aerial cable to the RF aerial in socket of the VCR.
3.
Store the VCR channel
4.
desired programme number using
the 'Manual programme tuning' section.
Select the programme number where the VCR channel is
on a
stored.
5.
Press the PLAY button
on
VCR
the VCR.
Audio/Video in sockets
1.
Connect the audio/video out sockets of the VCR to audio/video
in sockets of the set.
1
2.
Press the TV/AV button to select AV.
3.
Press the PLAY button
The VCR
on
playback picture
the VCR.
appears
on
the
screen.
If you have a mono VCR, connect the audio cable from the
VCR to the AUDIO L/MONO socket of the set.
Note
:
S-Video/Audio in sockets
When
connecting
picture quality will
1.
an
(S-Video)
S-VIDEO VCR to the S-VIDEO
be further
VCR
socket, the
improved.
Connect the S-Video socket of the VCR to the S-VIDEO socket
of the set.
2.
Connect the audio cable from the S-VIDEO VCR to the AUDIO
sockets of the set.
3.
Select S-Video
4.
Press the PLAY button
The VCR
26
by pressing
on
playback picture
the TV/AV button
repeatedly.
S-VIDEO VCR
the VCR.
appears
on
the
screen.
Connection of external
DVD
1.
input
sockets
Connect the DVD
1
or
Y PB
equipment
PR)
output sockets (Y Cb Cr, Y Pb Pr, Y B-Y R-Y
of the DVD to the DVD/DTV IN sockets
(Y
PB
PR)
of
the set.
2.
Connect the audio cable from the DVD to DVD/DTV IN AUDIO
sockets of the set.
3.
DVD
Press the TV/AV
or
4.
Component
or
MULTIMEDIA button to select Component 1
2.
Press the PLAY button
The DVD
on
playback picture
the DVD.
appears
on
the
screen.
DTV in sockets
1.
Connect the SET TOP
PB
2.
PR)
outputs
to the DVD/DTV IN sockets
(Y
of the set.
Connect the audio cable from the SET TOP to the AUDIO
sockets of the set.
3.
Press the TV/AV
or
DVD
Component
or
MULTIMEDIA button to select Component 1
2.
1
DTV Receiver
DTV Receiver
27
Connection of PC
PC in socket
Connect the signal cable from the monitor output socket of the
PERSONAL COMPUTER to the PC input socket of the set.
Connect the audio cable from the PC to the PC SOUND sockets
of the set.
Press the TV/AV or MULTIMEDIA button to select PC.
Switch on the PC, and the PC screen appears on the set.
The set can be operated as the PC monitor.
1.
2.
3.
4.
PERSONAL COMPUTER
Displayable
MODE
Monitor
Resolution
Connect the signal cable (DVI-D cable, Not DVI to D-Sub
cable) from the DVI output socket of the PC to the DVI input socket
of the set when using a PC with DVI output.
In some video cards, DVI-Analogue output may not be supported.
Note
:
Specification
Horizontal
Vertical
Frequency(kHz) Frequency(Hz)
VGA
640x480
31.4
60
SVGA
800x600
37.8
60
XGA
1024x768
48.3
60
1280x768
47.6
60
1360x768
47.6
60
WXGA
(Synchronization input
form
:
separate)
Note :
If the set is cold, there may be a small "flicker" when the set is switched on. This is normal, there is
a.
nothing wrong with the set.
b. If possible, use the VESA 1360x768@60Hz video mode to obtain the best image quality for your
LCD monitor. If used under the other resolutions, some scaled or processed pictures may appear
on the screen. The set has been pre-adjusted to the mode VESA 1360x768@60Hz.
c.
Some dot defects may appear on the screen, like Red, Green or Blue spots. However, this will have
no impact or effect on the monitor performance.
d. Do not press the LCD screen with your finger for a long time as this may produce some temporary
distortion effects on the screen.
e.
When the PC screen appears on the set, a message may appear on the screen, and the message
will differ according to the Window system version. If a message appears click "Next" until the message finishes.
f.
If the message "out of range" appears on the screen, adjust the PC as in the 'Displayable Monitor
Specification' section.
DPM (Display Power Management) mode
When the PC is in the power saving mode, automatically the monitor goes into DPM mode to
energy.
Note : Use the supplied signal cable with the set. Otherwise, DPM mode may not work.
28
save
the
Connection of PC
PC
PC
Setup (only DVI-Analogue mode)
H-Position
V-Position
You
adjust
configure,
can
auto
horizontal/vertical
reset
as
you
position, clock, phase,
prefer.
and
Clock
Phase
Auto
Configure
Reset
1.
Press the MENU button and then D / E button to select the
Setup
DEFG
menu.
3.
Press the G button and then D / E button to select Input.
Press the G button and then D / E button to select PC.
4.
Press the MENU button and then D / E button to select the PC
2.
OK
MENU
menu.
PC
H-Position
87
V-Position
Clock
Phase
Auto
TV/AV
Configure
Reset
MENU
DEFG
OK
MENU
5.
Press the G button and then D / E button to select the desired
picture item.
6.
Press the F / G button to make
H-Position / V-Position
This function is to adjust
appropriate adjustments.
PR
OK
VOL
picture
to
left/right
and
up/down
as
you
prefer.
VOL
PR
Clock
This function is to minimize any vertical bars or stripes visible on
the screen background. And the horizontal screen size will also
change.
Phase
This function allows you to remove any horizontal noise and
clear or sharpen the image of characters.
Auto Configure
This function is for the automatic adjustment of the screen
position, clock and phase. The displayed image will disappear
for a few seconds while the Auto-configuration is in progress.
Reset
This function allows you to return to the good picture
programmed at the factory and cannot be changed.
reproduction
?
Some signal from some graphics boards may not function
properly. If the results are unsatisfactory, adjust your monitor's
position, clock and phase manually.
Note
7.
8.
:
Press the OK button to store it for the PC monitor
Press the TV/AV button to return to PC mode.
picture.
29
External Control Device
-
Connect the RS-232C
input jack
to
and control the Monitor's functions
-
-
Connect the serial
external control device
are
(such
as a
computer
or an
A/V control
(option)
system)
externally.
port of the control device
RS-232C connection cables
RS-232C
an
Setup
; RS-232C
not
to the RS-232C
supplied
jack
on
the Monitor back
panel.
with the Monitor.
Setup
1
PC
Type
Type
of
of Connector; D-Sub 9-Pin
9-Pin Male
1
No.
Pin
1
No connection
2
RXD
3
TXD
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
name
5
(Receive data)
(Transmit data)
(DTE side ready)
(DCE side ready)
(Ready to send)
(Clear to send)
9
6
No Connection
9
RS-232C
Configurations
3-Wire
Configurations
(Not standard)
7-Wire
Configurations
(Standard RS-232C cable)
PC
TV
PC
TV
RXD
2
3
TXD
RXD
2
3
TXD
TXD
3
2
RXD
TXD
3
2
RXD
GND
5
5
GND
GND
5
5
GND
DTR
4
6
DSR
DTR
4
4
DTR
DSR
6
4
DTR
DSR
6
6
DSR
RTS
7
8
CTS
RTS
7
7
RTS
CTS
8
7
RTS
CTS
8
8
CTS
D-Sub 9
30
D-Sub 9
D-Sub 9
D-Sub 9
External Control Device
; RS-232C
Setup
(option)
Communication
Communication Parameters
?
Baud rate
?
Data
:
9600
length
Parity : None
?
*
Use
:
a
bps (UART)
?Stopbit:1bit
8 bits
crossed
?
(reverse)
Communication code
cable.
Command
Command Reference
Reference List
COMMAND COMMAND
2
1
01. Power
ASCII code
:
k
a
ransmission /
T
Transmission
DATA
(Hexa)
Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
0~1
*
[Command 1]: First command. (j or k)
[Command 2]: Second command.
[Set ID]: You can adjust the set ID to choose desired monitor
ID number in Special menu. Adjustment range is 1
99. When selecting Set ID '0', every connected
Input Select
Aspect Ratio
k
k
c
04. Screen Mute
k
d
0~1
05. Volume Mute
k
e
0~1
06. Volume Control
k
f
0~64
TV set is controlled. Set ID is indicated
07. Contrast
k
g
0~64
08.
k
h
0~64
(1~99)on menu and as Hexa decimal (0x0~0x63)
on transmission/receiving protocol.
02.
03.
b
Receiving
*
*
Brightness
1~4
*
~
*
09. Color
k
i
0~64
10. Tint
kj0~64
11.
k
k
0~64
k
l
0~1
k
m
0~1
14. Balance
k
t
15. Tune Command
m
16. Add/Delete
17.
Sharpness
12. OSD Select
13.
*
:
Key
Lock
Key
Refer to '02.
Input
[DATA]:
Transmit 'FF' data to read status of command.
*
[Cr]: Carriage
Return
ASCII code '0x0D'
*
[
]:
ASCII code
'space (0x20)'
0~64
OK Acknowledgement
mb
0~1
[Command2][ ][Set ID][ ][OK][Data][x]
m
Key
Select'
on
c
decimal
To transmit command data.
0~63
a
as
Code
*
page 32.
The Monitor transmits ACK
(acknowledgement)
this format when
normal data. At this
receiving
based
on
time, if the
data is data read
mode, it indicates present status data. If
the data is data write mode, it returns the data of the PC
computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
*
The Monitor transmits ACK
(acknowledgement)
this format when
abnormal data from non-viable
functions
or
receiving
communication
based
on
errors.
31
External Control Device
01. Power On
Setup
05. Volume Mute
(Command:a)
You
Transmission
also
mute on/off.
adjust
mute
Power Off
1
:PowerOn
on
[k][e][ ][Set ID][ ][Data][Cr]
Data 0
:
Volume mute off
1
:
Volume mute
[a][ ][Set ID][ ][OK][Data][x]
(Volume on)
(Volume off)
on
G To show Power On/Off.
Acknowledgement
Transmission
[e][ ][Set ID][ ][OK][Data][x]
[k][a][ ][Set ID][ ][FF][Cr]
06. Volume Control
Acknowledgement
Power Off
(Command:f)
G To adjust volume.
[a][ ][Set ID][ ][OK][Data][x]
:
the MUTE button
Transmission
Acknowledgement
Data 0
using
remote control.
[k][a][ ][Set ID][ ][Data][Cr]
:
can
(option)
(Command:e)
G To control volume
G To control Power On/Off of the TV.
Data 0
; RS-232C
You
1
adjust
volume with the volume buttons
remote control.
on
:PowerOn
also
can
Transmission
02.
Select
Input
G To select input
You
source
also select
can
button
(Command:b) (Main
an
Picture
Input)
for the TV.
input
source
Data
using
the TV/VIDEO
Min:0~Max:64
?
Refer to 'Real data
mapping
the TV's remote control.
on
0
:TV
4
:
2
:AV
5
:
3
:
S-Video
Component
Component
6or8
1
2
:PC
07. Contrast
G To adjust
You
screen
also
can
contrast.
adjust
contrast in the Picture
Transmission
[b][ ][Set ID][ ][OK][Data][x]
[k][g][ ][Set ID][ ][Data][Cr]
Data
Ratio
G To adjust the
You
(Command:c) (Main picture format)
screen
format.
also
adjust the screen format using the ARC
(Aspect Ratio Control) button on remote control or in the
can
Screen
Min:0~Max:64
?
Refer to 'Real data
as
shown below.
1
:
Normal
2
:
Wide
(4:3)
(16:9)
screen
screen
Brightness (Command:h)
You
in the Picture
menu.
Transmission
Data
Min:0~Max:64
?
Acknowledgement
Refer to 'Real data
mapping
Acknowledgement
[c][ ][Set ID][ ][OK][Data][x]
04. Screen Mute
(Command:d)
G To select
mute on/off.
screen
also
can
brightness.
adjust brightness
screen
[k][h][ ][Set ID][ ][Data][Cr]
Zoom is not available in PC mode.
[h][ ][Set ID][ ][OK][Data][x]
*
Real data
0
mapping
:Step0
Transmission
A:Step10
[k][d][ ][Set ID][ ][Data][Cr]
0
:
Screen mute off
1
:
Screen mute
on
(Picture on)
(Picture off)
Acknowledgement
[d][ ][Set ID][ ][OK][Data][x]
32
1'
[g][ ][Set ID][ ][OK][Data][x]
G To adjust
4:Zoom
Data
mapping
Acknowledgement
08.
[k][c][ ][Set ID][ ][Data][Cr]
*
menu.
menu.
Transmission
Data
shown below.
(Command:g)
Acknowledgement
Aspect
as
[f][ ][Set ID][ ][OK][Data][x]
[k][b][ ][Set ID][ ][Data][Cr]
03.
1'
Acknowledgement
Transmission
Data
[k][f][ ][Set ID][ ][Data][Cr]
F:Step15
10:Step16
64
:
Step
100
*Tint:-50~+50
1
1'
as
shown below.
External Control Device
09. Color
(Command:i)
G To adjust the
You
can
Setup
also
15. Tune Command
color.
screen
G Tune channel
color in the Picture
adjust
; RS-232C
to
menu.
(Command:m a)
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
[m][a][ ][Set ID][ ][Data0][ ][Cr]
Data
Data0:
?
Refer to 'Real data
Min
1'. See page 32.
mapping
:
0
number.
following Physical/major/minor
Transmission
Min:0~Max:64
(option)
Programme Number
Max : 63(transmit by
~
Hexadecimal
code)
Acknowledgement
[i][ ][Set ID][ ][OK][Data][x]
Acknowledgement
10. Tint
[a][ ][Set ID][ ][OK][Data0][x]
[a][ ][Set ID][ ][NG][Data0][x]
(Command:j)
G To adjust the
You
can
tint.(NTSC
screen
also
adjust
M
input only)
tint in the Picture
menu.
Transmission
16.
[k][j][ ][Set ID][ ][Data][Cr]
G To skip the
Data
Transmission
:Green0~Red :64
?
Refer to 'Real data
mapping
1'. See page 32.
Skip programme (Command:m b)
current programme.
[m][b][ ][Set ID][ ][Data 0][Cr]
Acknowledgement
Data0:
[j][ ][Set ID][ ][OK][Data][x]
(Programme)Skip on-0, (Programme)Skip
off-1
Acknowledgement
11.
Sharpness (Command:k)
G To adjust the
You
can
sharpness.
adjust sharpness in
[b][ ][Set ID][ ][OK][Data0][x]
[b][ ][Set ID][ ][NG][Data0][x]
screen
also
the Picture
menu.
Transmission
[k][k][ ][Set ID][ ][Data][Cr]
17.
Data
G To send IR
Min: 0
?
~
Max: 64
Refer to 'Real data
mapping
1'. See page 32.
Key (Command:m c)
key
code.
Transmission
Acknowledgement
[m][c][ ][Set ID][ ][Data][Cr]
[k][ ][Set ID][ ][OK][Data][x]
Data:
12. OSD Select
remote
(Command:l)
G To select OSD (On Screen Display)
Key
code
Acknowledgement
mute on/off.
[c][ ][Set ID][ ][OK][Data][x]
Transmission
[k][l][ ][Set ID][ ][Data][Cr]
Data
0: OSD mute
1: OSD mute off
on
Acknowledgement
[l][ ][Set ID][ ][OK][Data][x]
13.
Key
Lock
G To lock the
(Command:m)
remote control and the front
panel
controls
on
the TV.
Transmission
[k][m][ ][Set ID][ ][Data][Cr]
Data
0: Lock off
1: Lock
on
Acknowledgement
[m][ ][Set ID][ ][OK][Data][x]
?
If
the remote control and front panel controls
on the TV, use this mode. When main power is on/off,
remote control lock is released.
you're
not
14. Balance
using
(Command:t)
G To adjust balance.
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
Data
Min: 0
~
Max: 64
(transmit by
Hexadecimal
code)
Acknowledgement
[t][ ][Set ID][ ][OK][Data][x]
33
IR Codes
How to
to Connect
Connect
G
Connect your wired remote control to the Remote Control
port
on
the Monitor.
Remote Control
Control IR Code
Code
G Configuration of frame
?
1st frame
Lead
Low
High
code
custom code
custom code
Data code
Data code
C0 C1C2C3C4C5C6C7C0C1C2C3C4C5C6C7D0D1D2D3D4D5D6D7D0D1D2D3D4D5D6D7
?
Repeat
frame
Repeat
code
Tf
G Lead code
9ms
4.5
ms
0.55
G Repeat code
ms
9ms
2.25
ms
G Bit description
?
Bit "0"
?
0.56
0.56
ms
1.12
G Frame interval
:
Bit "1"
2.24
ms
Tf
The waveform is transmitted
Tf
as
long
as a
key
is
depressed.
Tf
Tf=108ms @455KHz
34
ms
ms
IR Codes
Code
Function
(Hexa)
Note
08H
POWER
R/C Button
0BH
TV/AV
R/C Button
98H
MULTIMEDIA
R/C Button
00H
PR
(D)
PR (E)
VOL (F)
VOL (G)
R/C Button
43H
MENU
R/C Button
44H
OK
R/C Button
79H
ARC
R/C Button
0AH
I/II
R/C Button
0EH
SLEEP
R/C Button
1AH
Q.VIEW
R/C Button
52H
SSM
R/C Button
4DH
PSM
R/C Button
01H
03H
02H
10H~19H
Number
Keys
(Power On/Off)
(TV/Video/S-video/Component1-2/RGB/DVI)
(Component1-2/PC/TV)
R/C Button
R/C Button
R/C Button
0~9
(4:3/16:9/Zoom/Auto)
R/C Button
09H
MUTE
R/C Button
20H
TEXT
R/C Button
22H
MODE
R/C Button
24H
MIX
R/C Button
26H
TIME
R/C Button
2AH
REVEAL
R/C Button
53H
LIST
R/C Button
61H
BLUE
R/C Button
62H
UPDATE
R/C Button
63H
YELLOW
R/C Button
64H
SIZE
R/C Button
65H
HOLD
R/C Button
70H
INDEX
R/C Button
71H
GREEN
R/C Button
72H
RED
R/C Button
35
check list
Troubleshooting
The
doesn't work
Power is
suddenly
turned off
normally.
?
if there is any
control causing obstruction.
?
Are batteries installed with correct
?
Correct remote
?
Install
new
?
Is the
sleep
?
Check the power control settings. Power interrupted
No broadcast on station tuned with Auto off activated.
The remote control
?
Check to
does not work
operation
see
operating
object
between the
polarity (+
mode set:
product
to +,
-
to
and the remote
-)?
TV, VCR etc.?
batteries.
timer set?
The video function does not work.
No
picture
&
No sound
Check whether the
?
Try
?
Is the power cord inserted into wall power outlet?
Check your antenna direction and/or location.
?
Picture appears
slowly after
switching
?
Test the wall power outlet, plug another product's power cord into the outlet
where the product's power cord was plugged in.
?
This is
on
or
poor color
poor
picture
normal, the image is muted during the product startup process.
Please contact your service center, if the
minutes.
?
or
with the broadcast.
?
?
No
another
product is turned on.
channel. The problem may be
?
?
?
has not
picture
appeared
after five
Adjust Color in menu option.
Keep a sufficient distance between the product and the VCR.
Try another channel. The problem may be with the broadcast.
Are the video cables installed properly?
Activate any function to restore the brightness of the picture.
Horizontal/vertical bars
ture
Poor
Lines
36
on
channels
or
Check for local interference such
?
Station
or
?
Station
signal
?
Check for
?
Check antenna
or
reception
some
in
picshaking
?
streaks
pictures
cable
is
as an
electrical
product experiencing problems,
weak, reorient
sources
of
possible
(Change
appliance
or
power tool.
tune to another station.
antenna to receive weaker station.
interference.
the direction of the
antenna).
Troubleshooting
check list
The audio function does not work.
No
?
Press the VOL
Picture OK &
?
Sound muted? Press MUTE button.
No sound
?
Try
?
Are the audio cables
?
Adjust
?
A
output from
of the
one
another channel. The
Balance in
problem may be
installed properly?
menu
with the broadcast.
option.
speakers
Unusual sound
from inside the
change
in ambient
noise when the
product
the
humidity or temperature may result in an unusual
product is turned on or off and does not indicate a fault with
product.
There is
a
(Only
The
button.
(or Volume)
signal
range.
Vertical bar
PC mode
horizontal
?
Adjust resolution,
?
Check it whether the
?
Check the
?
Work the Auto
?
Check the
?
Reinstall the PC video card.
is out of
input
in PC mode.
problem
applied)
frequency,
or
vertical
cable is connected
signal
or
frequency.
loose.
source.
or
stripe on background &
configure
or
adjust clock, phase,
or
H/V
position.
Horizontal Noise &
Incorrect
position
Screen color is
unstable
or
single
signal
cable.
color
37
Memo
38
Memo
39
Download PDF

advertising