LG | RT-37LZ55 | LG RT-37LZ55 Owner’s Manual

LCD TV
OWNER'S MANUAL
MODEL: RT-37LZ55
Please read Information Manual included together
before reading this manual and operating your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached
and quote
this information to your dealer when you require service.
on
the back
P/NO
:
cover
38289U0496G(0510-REV01)
Printed in Korea
Accessories
Ensure that the
dealer from
following accessories are included
where you purchased the product.
Owner's Manual
D-SUB cable
2
(PC)
Power Cord
Audio cable
with your TV. If any accessory is
missing, please
Remote Control / Batteries
(PC)
2-TV Bracket Bolts
contact the
Twister Holder
2-TV
Brackets, 2-Wall Bracket
Contents
Contents
Accessories
2
Introduction
Installation
5
Controls
6
Connection
7
Remote
10
Basic Connection
12
External
12
13
Headphone
VCR Setup
14
Monitor Out
15
DVD
21
Power Cord Connection
22
Turning
22
Volume
Operation
Sound
adjustment
adjustment
Time
menu
On/Off the TV
22
Adjustment
Programme selection
22
On
23
How to
24
25
Auto programme tuning
Manual programme tuning
26
Fine
26
27
28
Picture
Setup
21
20
up
TV stations
Socket
Setup
STB ( Set-Top Box) Setup
Cable TV Setup
External AV Source Setup
PC Setup
Supported display resolution
19
Setting
Connections
Antenna Connection
18
operation
Equipment
Functions
12
16
Basic
Options
Control Key
language
screen
selection
the OSD
adjust
tuning
Assigning a station
Programme edit
screen
name
28
Favourite programme
Calling the programme table
29
PSM
(Picture
Status
Memory)
29
CSM
(Colour
Status
Memory)
Function
30
30
ACM
31
sRGB
31
Manual Picture
32
SSM
32
SRS WOW
33
AVL
33
Manual Sound
34
TV
35
I/II
36
Clock
36
On/Off Time
37
Auto
37
Sleep
(Active
(Sound
(Auto
Colour
Management)
Adjustment
Status
Memory)
Volume
leveler)
Adjustment
Speaker
Setup
Sleep
Timer
3
38
Input
38
Child Lock
39
Demo
40
Operation
Reference
40
Configure
Manual Configure
41
XGA Mode
41
Picture Size Zoom
42
Picture format
43
Screen Position
43
Cinema
44
NR
(ARC)
45
(Noise Reduction)
Reset to original factory
46
Switch on/off
46
SIMPLE text
46
TOP text
47
FASTEXT
47
Special
48
External Control Device
52
IR codes
54
Programming the Remote control
Programming Codes
Troubleshooting Checklist
Product Specifications
55
57
59
4
Auto
(This
value
(Initializing)
feature is not available in all
teletext functions
Setup
; RS-232C
countries.)
Introduction
Controls
Controls
-
-
This is
a
simplified representation
of front
panel.
Here shown may be somewhat different from your TV.
Programme
(E/D)Buttons
Volume
(F
/
G)
Buttons
OK Button
Menu Button
INPUT Button
ON/OFF Button
Remote Control Sensor
Power/Standby
?
?
Indicator
( )
illuminates red in standby mode.
illuminates green when the set is
switched on.
5
Introduction
Connection
Connection
Options
Options
Headphone
Socket
COMPONENT2
input
(Y,PB,PR / Audio)
HDMI
(High
Definition Multimedia
RGB
Interface)/DVI input
Input
PC SOUND
Variable AUDIO OUT
Input
ports
Monitor Out
AC
AV
Input
Antenna
(Video/Audio) Input
Remote Control Port
S-Video
Input
COMPONENT1
(Y,PB,PR / Audio)
RS-232C
6
Input
input
Input
Introduction
Remote Control
Control
Key
Functions
TV
Returns to TV
from any mode.
viewing
POWER
switches the set
on
from
standby
or
off to
standby.
INPUT
If you press the button once, the input source OSD will
appear on screen as shown. Press the D / E button
Input
TV
AV
and then OK button to select the desired
input source
(TV, AV S-Video, Component 1, Component 2,
RGB PC/RGB DTV, or HDMI PC/ HDMI DTV).
S-Video
Component
1
Component
2
,
RGB PC
1
HDMI PC
MODE
Selects the remote
or
operating
modes.
:TV, DVD, VCR, AUDIO, CABLE
STB
ZOOM-/ZOOM+
Enlarges
or
reduces the main
picture
size.
SLEEP
Sets the
sleep
timer.
(Refer
to
p.37)
PSM
(Picture Status Memory)
Recalls your preferred picture setting. (Refer
to
p.29)
SSM
(Sound Status Memory)
Recalls your preferred sound setting. (Refer to p.32)
I/II
?
Selects the sound
output.
2
*
1
:
No function
ARC
Selects your desired
4
picture
*COLOURED BUTTONS
TELETEXT
2
models)
or
format
:
(Refer
to
These buttons
p.42).
are
used for teletext
(only
Programme edit.
FAVOURITE
Displays
the selected favourite programme
(Refer
to
p.28).
(Without TELETEXT)
7
MENU
Selects
3
a menu.
TELETEXT BUTTONS
(This
feature is not available in all
tries. )
These buttons are used for teletext.
For further details, see the 'Teletext' section
1
(Refer
to
p.46).
EXIT
Clears all
2
on-screen
displays
and returns to TV
menu.
3
D/E/F/G(up/down/left/right)
Selects or adjusts an item in the menu.
OK
your selection
Accepts
displays
or
the current mode.
(Volume) D / E
Adjusts the volume.
VOL
MUTE
Switches the sound
on or
off.
LIST
Displays
PR
the programme table
(Programme)
Selects
a
(Refer
to
p.28).
D / E
programme.
0-9 number buttons
?
Selects a programme.
?
Selects numbered items in
a menu.
Q.VIEW
Returns to the
previously
viewed programme.
3
4
VCR/DVD Control buttons
Controls
4
(With TELETEXT)
8
coun-
a
LG video cassette recorder
or
DVD.
viewing
from any
Introduction
Remote Control
Control
Installing
1
2
Open
the
cover on
Key
Functions
Batteries
battery compartment
the back side.
Insert two 1.5V AA size batteries
in correct
-).
polarity (+ with +, with
Don't mix old or used batteries
with
-
new ones.
*
Use
a
remote control at 7
meter distance and 30
3
*
Close the
Dispose
(left/right/up/down) within
receiving unit scope.
cover.
of used batteries in the
degree
recycle
bin to
the
prevent environment.
9
Installation
Basic Connection
Connection
Connect the cables
as
necessary.
After connecting the cables neatly,
arrange the cables to the Cable
Holder.
To connect
an
additional
equipment,
equipment
the External
Connections section.
see
Pull the cables
on
through
the hole
the set and bundle the cables
using
the
supplied
twister holder.
Wall Mount: Horizontal installation
For proper ventilation, allow a clearance of 4" on each side and from
the wall. Detailed installation instructions are available from your
dealer, see the optional Tilt Wall Mounting Bracket Installation and
Setup
Desktop
Guide.
Pedestal Installation
For proper
the wall.
10
ventilation, allow
a
clearance of 4"
on
each side and from
How to
-
-
join
the
product assembly
to the wall to
protect the
set
tumbling
Set it up close to the wall so the product doesn't fall over when it is pushed backwards.
The instructions shown below is a safer way to set up the product, which is to fix it on the wall
uct doesn't fall
ward and
over
when it is
hurting people.
that children don't climb
pulled
It will also
on or
hang
in the forward direction. It will
prevent the product from
the
prodfalling for-
so
prevent the product from damage caused by fall. Please make
from the
sure
product.
1
2
3
1
Use the bracket and the bolt to fix the
2
Secure the bracket with the bolt
3
product
(not provided
to the wall
as
as
shown in the
parts of the product,
picture.
must
purchase separately)
on
the wall.
Use
rope (not provided as parts of the product, must purchase separately) to tie the
It is safer to tie the rope so it becomes horizontal between the wall and the product.
a
sturdy
product.
Notes
?
?
?
When
moving the product to another place undo the ropes first.
Use a product holder or a cabinet that is big and strong enough for the
To use the product safely make sure that the height of the bracket that
as that of the product.
size and
weight
is mounted
on
of the
product.
the wall is
same
11
Installation Instruction
External
To prevent the
all equipment.
Connections
Connections
Equipment
equipment from damage,
never
plug
in any power cords until you have finished
connecting
Antenna Connection
-
-
For
optimum picture quality, adjust
An antenna cable and converter
antenna direction.
are
not
supplied.
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
Wall Antenna Socket
RF Coaxial Wire
(75 ohm)
VHF Antenna
Turn clockwise to
tighten.
UHF Antenna
Outdoor Antenna
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
?
?
In poor signal areas, to get better picture quality, install
nal amplifier to the antenna as shown to the right.
If
needs to be
signal
nal splitter
split
for two
TVs,
use an
a
antenna
sigsig-
VHF
UHF
for connection.
Signal
Amplifier
Headphone Socket
-
You
can
listen to the sound
1
through
the
headphone.
1
Plug
2
To
headphone
adjust
the
into the
headphone
socket.
press the VOL
D / E button. If you press the MUTE button, the
sound from the headphone is switched off.
?
12
the
headphone volume,
While you are listening to sound
TV speakers will not be heard.
through
a
headphone,
VCR
-
-
To avoid
picture
Typically
a
noise
frozen still
may remain visible
When
on
connecting
Setup
(interference), leave an adequate distance between
picture from a VCR. If the 4:3 picture format is used;
the
the VCR and TV.
the fixed
images
on
the sides of the
screen
screen.
with
an
antenna cable
TV Back
panel
2
ANT IN
ANT OUT
S-VIDEO
OUT
(R)
1
Connect the ANT OUT socket of the VCR to the Antenna socket
2
Connect the antenna cable to the ANT IN socket of the VCR.
3
Press the PLAY button
When
connecting
with
a
the VCR and match the
(L)
VIDEO
IN
1
on
AUDIO
appropriate
on
VCR
the set.
programme between the TV and VCR for
viewing.
RCA cable
TV Back
panel
1
ANT IN
ANT OUT
S-VIDEO
OUT
(R)
AUDIO
(L)
VIDEO
VCR
IN
1
Connect the AUDIO/VIDEO
=
white, and Audio Right
2
Insert
3
Select AV
a
video
=
jacks
red)
between TV and VCR. Match the
tape into the VCR and press PLAY
input
source
with
using
on
the INPUT button
the VCR.
on
jack colours (Video
(Refer
=
to the VCR owner's
yellow,
Audio Left
manual.)
the remote control.
13
Installation Instruction
External
When
Equipment
with
connecting
TV Back
an
Connections
Connections
S-Video cable
panel
1
2
ANT IN
ANT OUT
S-VIDEO
OUT
(R)
AUDIO
(L)
VIDEO
VCR
IN
1
Connect the S-VIDEO
pared
to
connecting
2
Connect the AUDIO
3
Insert
4
Select S-Video
a
video
a
output of the VCR
regular VCR
jacks
to the S-VIDEO
to the Video
The TV has
a
on
the set. The
picture quality
tape into the VCR and press PLAY
input source
with
using
on
the VCR.
the INPUT button
special signal output capability
on
(Refer
to the VCR owner's
Connect the second TV
See the
a
second TV
Manual of the second TV
monitor for further details
14
or
monitor.
panel
IN
AUDIO
(L)
VIDEO
monitor to the TV's
jacks.
Operating
input settings.
or
manual.)
Setup
(R)
2
com-
the remote control.
which allows you to hook up
S-VIDEO
MONITOR OUT
improved;
between TV and VCR.
TV Back
1
is
input.
Monitor Out
-
input
regarding
or
that device's
?
TV, or AV input sources
?
When
can
be used for Monitor out.
connecting with external audio equipments,
such as amplifiers or speakers, please turn the TV
speakers off. (Refer to p.34)
DVD
When
connecting
TV Back
with
a
Setup
component cable
panel
1
Connect the video
to
outputs (Y, PB, PR) of the DVD
the COMPONENT VIDEO (Y, PB, PR) jacks on
the set.
2
1
Connect the audio
outputs of the DVD
PONENT AUDIO
jacks
3
Turn
player,
4
Select
on
the DVD
Component
INPUT button
2
-
If connected to
input
5
on
1
on
to the COM-
the set.
insert
input
a
DVD.
with
source
using
the
the remote control.
Component 2,
select
Component 2
source.
Refer to the DVD
player's
manual for
operating
instructions.
DVD
B
TV side
R
panel
?
Component Input ports
To get better picture quality, connect a DVD player
to the component input ports as shown below.
Component ports
Video
on
(R)
AUDIO
(L)
R
on
the TV
output ports
DVD
player
YPBPR
Y
Pb
Pr
Y
B-Y
R-Y
Y
Cb
Cr
Y
PB
PR
B
DVD
15
Installation
External
When
Equipment
connecting
with
Connections
Connections
HDMI cable
a
TV Back
panel
1
DVD
HDMI OUTPUT
Connect the HDMI
1
on
output of the DVD player to the HDMI/DVI jack
the set.
?
2
Select HDMI DTV
input
source
with
using
the INPUT button
on
Refer to the DVD
player's
manual for
operating
STB
When
connecting
with
TV Back
a
on
16
using
a
HDMI cable.
component cable
panel
2
DTV Receiver
R
outputs (Y, PB, PR) of the digital set-top box
(Set-top Box)
to the COMPONENT VIDEO
(Y, PB, PR) jacks
the set.
2
Connect the audio
3
Turn
4
Select
-
with
on
the
signal
( Set-Top Box) Setup
B
Connect the video
receive the video and audio
instructions.
1
1
can
simultaneously
the remote control.
3
TV
outputs of the digital set-top box
digital set-top
box.
(Refer
to the COMPONENT AUDIO
to the owner's manual for the
jacks
digital set-top box.)
Component 1 input source with using the INPUT button on the
If connected to Component 2, select Component 2 input source.
remote control.
on
the set.
When
connecting
with
TV Back
a
HDMI cable
panel
1
HDMI-DTV OUTPUT
1
Connect the HDMI
HDMI/DVI
2
Turn
on
on
(Set-top Box)
to the
the set.
digital set-top box. (Refer
digital set-top box.)
Select HDMI DTV
ton
When
on
the
al for the
3
jack
output of the digital set-top box
DTV Receiver
input
source
with
to the owner's
manu?
using
TV
can
receive the video and audio
taneously
the INPUT but-
with
using
a
signal
simul-
HDMI cable.
the remote control.
connecting
with
a
D-Sub cable
TV Back
1
panel
2
RGB-DTV OUTPUT(R) AUDIO
DTV Receiver
(L)
(Set-top Box)
1
Connect the RGB
output of the digital set-top box to the RGB INPUT jack
on
the
set.
2
Connect the audio
3
Turn
on
the
outputs of the set-top box
digital set-top
box.
(Refer
to the PC SOUND
jack
to the owner's manual for the
on
the set.
digital
set-
top box.)
4
Select RGB DTV
input
source
with
using
the INPUT button
on
the remote
control.
17
Installation
External
Equipment
Connections
Connections
Cable TV
-
-
After
subscribing
to
a
For further cable TV
When
connecting
local cable TV service and
information,
with
contact
a
installing
a
Setup
converter, you
local cable service
can
watch cable TV programmes.
provider.
RCA cable
a
TV Back
panel
1
VIDEO
TV
S-VIDEO
Cable Box
VCR
1
Connect the AUDIO/VIDEO jacks between TV and Cable Box. Match the jack colours
=
white, and Audio Right
=
Select AV
3
Select programmes with the cable box remote control.
When
connecting
source
with
an
=
yellow, Audio
Left
red)
2
input
(Video
with
using
the INPUT button
on
the remote control.
S-Video cable
TV Back
panel
1
2
VIDEO
TV
S-VIDEO
Cable Box
18
VCR
1
Connect the S-VIDEO
output of the Cable Box
2
Connect the AUDIO
3
Select S-Video
4
Select programmes with the cable box remote control.
jacks
input
to the S-VIDEO
input
on
the set. The
between TV and Cable Box.
source
with
using
the INPUT button
on
the remote control.
picture quality
is
improved.
External AV Source
When
with
connecting
TV Back
a
Setup
RCA cable
panel
1
Camcorder
Video Game Set
S-VIDEO
1
Connect the AUDIO/VIDEO
Audio Left
2
Select AV
3
Operate
When
=
jacks between
white, and Audio Right red).
VIDEO
TV and external
source
with
with
connecting
an
using
the INPUT button
external
corresponding
TV Back
equipment.
on
Match the
colours
jack
(Video
=
yellow,
the remote control.
Refer to external
equipment operating guide.
S-Video cable
panel
2
1
S-VIDEO
1
equipment.
=
input
the
AUDIO
RL
Connect the S-VIDEO
Camcorder
AUDIO
RL
output of the external equipment
Video Game Set
VIDEO
to the S-VIDEO
input
on
the set. The
picture quality
is
improved.
2
Connect the AUDIO
3
Select S-Video
4
Operate
the
jacks
input
between TV and external
source
corresponding
with
using
external
equipment.
the INPUT button
equipment.
on
the remote control.
Refer to external
equipment operating guide.
19
Installation
External
Connections
Connections
Equipment
PC
When
connecting
TV Back
with
a
Setup
D-sub cable
panel
PC
1
Connect the RGB
2
Connect the PC audio
3
Turn
4
Select RGB PC
When
on
output of the PC
output
to the RGB INPUT
to the PC SOUND
jack
jack
on
the set.
the set.
on
the PC and the set.
connecting
input
with
TV Back
a
source
with
using
the INPUT button
on
the remote control.
HDMI to DVI cable
panel
1
PC
DVI OUPUT
1
Connect the DVI
2
Connect the PC audio
3
Turn
4
Select HDMI PC
?
20
on
output of the PC
output
AUDIO
to the HDMI/DVI
to the PC SOUND
jack
jack
on
on
the set.
the set.
the PC and the set.
If the PC has
a
input
DVI
source
with
output and
no
using
HDMI
the INPUT button
output,
a
on
separated
the remote control.
audio connection is necessary.
Supported display
A
PC
(Monitor Display Specifications)
Resolution
720
x
640
x
Vertical
Frequency(kHz)
Frequency(Hz)
400
31.468
70
480
31.469
37.500
60
75
60
75
800
x
600
832
x
624
49.725
75
48.363
56.470
60.123
60
70
75
47.776
60
47.720
60
1024
x
768
(XGA)
x
768
(WXGA)
1360
x
768
(WXGA)
1366
x
768
(WXGA)
Note
Horizontal
37.879
46.875
1280
a.
optimum picture quality,
b.
c.
computer output
use
at
a
standard WXGA
60Hz refresh rate.
(VGA, SVGA, etc.) or refresh
rates may result in reduced picture quality. (To
change the computer video output format, please
refer to the operating manual for the computer you
are using).
If the message No signal appears on the screen,
adjust the PC output to a format listed in the
Monitor Display Specifications table.
The synchronization input form for Horizontal and
Vertical frequencies is separate.
Using
DPM
other formats
(Display
Power
Management) mode
power saving mode, the monitor automatically
If the PC goes to
switches to DPM mode.
60
47.720
For
1360x768
If you don't
-
A
resolution
use
the PC cable
provided,
DPM mode is not available in HDMI
DPM mode may not work.
PC mode.
DTV
Mode
Terminal
Component
RGB
(DTV)
HDMI
(DTV)
480i
o
x
x
576i
o
x
x
480p
o
o
o
576p
o
o
o
720p
o
o
o
1080i
o
o
o
Power Cord Connection
-
Connect the power cord
correctly
as
shown.
21
Operation
Operation
Basic
Operation
Operation
Turning On/Off
1
the TV
First, make all equipment connections. Connect the AC power cord into the TV,
then
the power cord into a wall outlet. Press the POWER button located
the TV to turn on the TV. The power indicator will change from RED to
GREEN.
?
plug
In the
tons
press the POWER, PR D
the remote control to turn on the TV.
standby mode,
on
/
E, TV, INPUT
on
number but-
or
2
If you want to turn the TV off, press the POWER button located
control. If you intend to be away on vacation, disconnect the
on
the remote
plug
from the
wall outlet.
Volume
Adjustment
1
Press the VOL D
2
If you want to switch off the sound, press the MUTE button.
You can cancel this function by pressing the MUTE, VOL D / E, I/II
button to
/ E
adjust
Programme
1
Press the PR D
/ E or
On
22
screen
language
Press the MENU button and then D
2
Press the G button and then D
/ E
3
Press the G button and then D
/ E
on screen
displays
or
SSM button.
selection
NUMBER buttons to select
1
All the
the volume.
/ E
a
programme number.
selection
button to select the SPECIAL
button to select
Language.
button to select your desired
will appear in the selected language.
4
Press the OK button.
5
Press the EXIT button to return to TV
viewing.
menu.
language.
How to
adjust
the OSD
1
Press the MENU button and then D / E button to
2
Press the G button and then D / E button to select
3
Change
You
STATION G
the
setting
can move
of
to the
Auto programme
an
item in the sub
higher
level
menu
Programme edit
menu.
item.
with F / G button.
or
MENU button.
PSM
STATION
STATION
CSM
PICTURE
ACM
TIME
Contrast
90
Brightness
55
Colour
55
Sharpness
60
SOUND G
TIME
SPECIAL
SPECIAL
SCREEN
SCREEN
SCREEN
STATION
Auto
config.
Manual
STATION
config.
XGA Mode
PICTURE
PICTURE
menu
ARC
SOUND
Input
STATION
SOUND
50
Bass
50
TV
speaker
menu
Clock
Off time
Child lock
PICTURE
Set ID
Zoom +/-
0
Treble
SOUND
menu
Language
PICTURE
AVL
Balance
SPECIAL
STATION
SSM
SRS WOW
PICTURE G
SOUND
TIME
a menu
pull-down menu
by pressing the OK
Favourite programme
SOUND
each
or
Manual programme
PICTURE
display
screen
On time
Auto
Demo
sleep
SOUND
Position
TIME
Cinema
TIME
TIME G
SPECIAL G
SPECIAL
SCREEN
SCREEN
NR
SPECIAL
Reset
SCREEN G
SCREEN
menu
SPECIAL
menu
TIME
menu
Note
a.
b.
c.
The OSD
(On Screen Display) function enables you to adjust the screen status conveniently since it provides graphical presentation.
In this manual, the OSD (On Screen Display) may be different from your TV's because it is just example
to help the TV operation.
In the teletext mode, menus are not displayed
23
Setting
Up
to 100 TV stations
can
TV
stations
stations
up
up
be stored
by
programme numbers
you will be able to use the D / E or NUMBER buttons to
Stations can be tuned using automatic or manual modes.
Auto programme
Manual programme
PICTURE
Programme edit
SOUND
TIME
TIME
SPECIAL
SPECIAL
SCREEN
SCREEN
Programme edit
Start
Menu
be received
are stored by this method. It is
recommended that you use auto
programme during installation of
this set.
BG
1
Favourite programme
SOUND
All stations that
programmed.
System
Storage from
Favourite programme
-
G
Manual programme
PICTURE
preset the stations,
tuning
Auto programme
STATION
Once you have
99).
the stations you have
scan
Auto programme
STATION G
to
(0
can
1234
56
78
Prev.
Press the MENU button and then D
/ E
Press the G button and then D
/ E
button to select Auto programme.
Press the G button and then D
/ E
button to select
Press the F
a
/ G
button to select
TV
button to select the STATION
system
BG
:
PAL
I
:
PAL I/II
DK
:
PAL
M
:
(USA/Korea/Philippines)
Press the D
Press the F
/ E
/ G
menu.
System.
menu;
B/G, SECAM B/G (Europe/East Europe)
(U.K./Ireland)
D/K, SECAM D/K (East Europe)
button to select
button
or
Storage from.
NUMBER buttons to select the
beginning
programme number. If you use NUMBER buttons, any number under 10 is
entered with a numeric '0' in front of it, i.e.'05' for 5.
Press the D
/ E
button to select Start.
Press the G button to
begin
All receivable stations
are
Option
:
In
Australia, if
the channel number is
ber
To
'Assigning
see
a
auto
programming.
stored.
no
station
assigned
name can
and stored
be
as
station name' section to
assigned
-----
to
followed
assign
a
station,
by
a num-
the station
name.
programming, press the MENU button.
When auto programming is completed, the Programme edit menu appears
on the screen. See the Programme edit section to edit the stored prostop
auto
gramme.
9
24
Press the EXIT button to return to normal TV
viewing.
Manual programme
STATION G
Auto programme
Auto programme
STATION
Manual programme
PICTURE
tuning
Storage
5
Programme edit
System
BG
Favourite programme
Band
Manual programme
Programme edit
PICTURE
Favourite programme
SOUND
G
V/UHF
Channel
SOUND
5
Fine
TIME
TIME
Search
Name
SPECIAL
SPECIAL
SCREEN
SCREEN
C05
Prev.
Menu
-
Manual programme lets you manually tune and arrange the stations
in whatever order you desire.
Press the MENU button and then D
1234
56
789
10
Press the G button and then D
Press the F
/ G
button
button to select the STATION
menu.
button to select Manual programme.
/ E
Press the G button and then D
/ E
/ E
button to select
Storage.
NUMBER buttons to select the desired proIf you use NUMBER buttons, any number under
or
gramme number (0 to 99).
10 is entered with a numeric '0' in front of it, i.e. '05' for 5.
Press the D
/ E
button to select
System.
Press the F
/ G
button to select
a
TV
system
BG
:
PAL
I
:
PAL I/II
DK
:
PAL
M
:
(USA/Korea/Philippines)
menu;
B/G, SECAM B/G (Europe/East Europe)
(U.K./Ireland)
D/K, SECAM D/K (East Europe)
Press the D
/ E
button to select Band.
Press the F
/ G
button to select
Press the D
/ E
button to select Channel.
V/UHF or Cable.
select the desired programme number with the F / G button or
number buttons. If possible, select the programme number directly with the
You
can
number buttons.
of
it, i.e. '05' for
11
Press the D
12
Press the F
search will
Any
number under 10 is entered with
a
numeric '0' in front
5.
button to select Search.
/ E
/ G
button to
commence
searching.
If
a
station is found the
stop.
13
Press the OK button to store it.
14
To store another
15
Press the EXIT button to return to normal TV
station, repeat steps 3
to 13.
viewing.
25
Setting
TV
stations
stations
up
up
Fine
STATION G
Auto programme
tuning
Auto programme
STATION
Manual programme
Manual programme
Programme edit
PICTURE
5
Programme edit
System
BG
Favourite programme
Band
PICTURE
Storage
Favourite programme
SOUND
G
V/UHF
Channel
SOUND
5
Fine
TIME
TIME
FG
Search
Name
SPECIAL
SPECIAL
SCREEN
SCREEN
Normally fine tuning is only necessary if reception is poor.
-
Store
Press the MENU button and then D
123456
Press the G button and then D
Press the F
Auto programme
button to to fine tune for the best
station
a
picture
and sound.
viewing.
name
Auto programme
Storage
5
Programme edit
System
BG
Favourite programme
Band
Manual programme
PICTURE
Favourite programme
SOUND
button to select Fine.
/ E
Press the EXIT button to return to normal TV
STATI ON
Programme edit
menu.
Press the OK button to store it.
Manual programme
PICTURE
/ G
button to select the STATION
/ E
button to select Manual programme.
/ E
Press the G button and then D
Assigning
STATION G
C05
G
V/UHF
Channel
SOUND
5
Fine
TIME
TIME
Search
Name
SPECIAL
SPECIAL
SCREEN
SCREEN
G
C05
Store
You
-
can
assign
a
station
name
with five characters to each programme number.
Press the MENU button and then D
1234
5
Press the G button and then D
Press the G button and then D
number 0 to 9 and the
Press the F
the second
26
/ G
/ E
/ E
alphabet
menu.
button to select Name.
button. You
can use a
blank,
+,
-,
the
A to Z.
button to select the
character, and
button to select the STATION
button to select Manual programme.
/ E
Press the G button and then D
/ E
position
and make your choice of
so on.
6
Press the OK button to store it.
7
Press the EXIT button to return to normal TV
viewing.
Programme
STATION G
Auto programme
STATION
Auto programme
Manual programme
Manual programme
PICTURE
edit
Programme edit
PICTURE
Programme edit
G
To set
Favourite programme
Favourite programme
SOUND
SOUND
TIME
TIME
SPECIAL
SPECIAL
Programme edit
0-
SCREEN
SCREEN
Menu
-
-
-
This
delete
function
or
skip
enables you to
the stored pro-
grammes. Also you can move
some
stations to other pronumbers
or
a
gramme
copy
blank station data into the select-
Press the MENU button and then D
123
1BLN2
6C07
2C01
7C55
3C04
8S27
4C05
9S29
Delete
Copy
Move
Skip
Prev.DEFG
ed programme number.
button to select the STATION
/ E
Press the G button and then D
/ E
Press the G button to
Programme edit
A
Deleting
1.
Select
2.
a
display
the
edit.
menu.
programme to be deleted with the D / E / F / G button.
Press the RED button twice.
Copying
1.
Select
a
All the
following
1.
Programme
a
A
A
button to select
menu.
programme
The selected programme is
shifted up one position.
2.
5C05
Prev.
Menu
-
-
a
deleted, all the following programmes
are
programme
programme to be
Press the GREEN button.
copied
programmes
are
with the D / E / F / G button.
shifted down
one
position.
Moving a programme
SelectaprogrammetobemovedwiththeD/E/F/Gbutton.
2.
Press the YELLOW button.
3.
Move the programme to the desired programme number with the D / E
/F/Gbutton.
4.
A
Press the YELLOW button
Skipping
a
again
to release this function.
programme number
2.
programme number to be skipped with the D / E / F / G button.
Press the BLUE button. The skipped programme turns to blue.
3.
Press the BLUE button
1.
Select
When
a
to release the
again
skipped
programme.
that you will be unable
programme number is skipped it means
to select it using the D / E button during normal TV viewing. If you want
to select the skipped programme, directly enter the programme number
a
with the NUMBER buttons
or
select it in the programme edit
or
table
menu.
4
Press the EXIT button to return to normal TV
viewing.
27
Setting
TV
stations
up
up
Favourite programme
STATION G
Auto programme
Auto programme
STATION
Manual programme
Manual programme
PICTURE
Programme edit
Programme edit
PICTURE
Favourite programme
Favourite programme
SCREEN
SCREEN
Menu
-
This function lets you select your
favourite programmes directly.
Repeatedly press the FAV button to
select stored favourite programmes.
You
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Prev.
Press the MENU button and then D
12345
Press the G button and then D
/ E
/ E
menu.
button to select Favourite programme.
PresstheD/Ebuttontoselect-
-
-
-
-
-
-.
Select a desired programme with the F / G button or NUMBER buttons.
number under 10 is entered with a numeric '0'in front of it, i.e.'05' for 5.
6
To store another programme, repeat
You can store up to 8 programmes.
7
Press the EXIT button to return to normal TV
steps 4
Any
to 5.
viewing.
the programme table
check the programmes
stored in the memory by displaying
A
the programme table.
The programme table appears on the
tains ten programmes as below.
can
button to select the STATION
Press the G button.
Calling
-
-
SPECIAL
SPECIAL
-
-
TIME
TIME
BLN2
-
G
SOUND
SOUND
0
FG
Displaying programme table
Press the LIST button to display the Programme
screen.
0-
-
-
-
-
table
menu.
One programme table
con-
5C05
1BLN2
6C07
2C01
7C55
3C04
8S27
4C05
9S29
DEFG
Note
LIST
A
a.
You may find some blue programmes. They have been set up to
be skipped by auto programming or in the programme edit mode.
b.
Some programmes with the channel number shown in the programme table indicate there is no station name assigned.
Selecting
a
programme in the programme table
programme with the D / E / F / G button. Then press the OK button. The set switches to the chosen programme number.
Select
A
a
Paging through
There
a
programme table
10 programme table pages in which contain 100 programmes.
the D / E / F / G button repeatedly turns the pages.
are
Pressing
Press the EXIT button to return to normal TV
28
viewing.
Picture
adjustment
PSM
-
-
-
-
(Picture Status Memory)
This function adjusts the set for
the best picture appearance.
When
adjusting Contrast,
Brightness, Colour,
Sharpness, and Tint (NTSC
only) manually, PSM automatically
changes to User.
PSM
Dynamic, Standard, and Mild
are programmed for optimum picture reproduction at the factory
and cannot be changed.
You
the PICTURE
to adjust PSM.
can
menu
also
Dynamic
use
1
CSM
STATION
Press the PSM button
option
as
(Colour Status Memory)
PSM
STATION
CSM
Normal
Contrast
90
Brightness
55
Colour
55
Sharpness
60
SOUND
TIME
SPECIAL
SPECIAL
SCREEN
SCREEN
ACM
Warm
Contrast
User
Brightness
Red
0
Colour
Green
0
Sharpness
Blue
0
Menu
-
-
For initialized values
(reset to default
settings), select the Normal option.
When
Cool
G
PICTURE
ACM
TIME
PSM
CSM
PICTURE G
SOUND
shown
repeatedly to select the picture appearance setup
below: Dynamic, Standard, Mild, or User.
adjusting colour temperature
options (Red, Green, or Blue)
CSM
manually,
automatically
changes to User.
Prev.
Press the MENU button and then D
123
Press the G button and then D
/ E
Press the G button and then D
/ E
button to select the PICTURE
menu.
button to select CSM.
button to select
Cool, Normal, Warm,
User.
?
Cool : To see less intense colors with more blue.
?
Normal : To initialize values (reset to default settings).
?
Warm : To enhance hotter colors such as red.
?
User : To adjust red, green, blue to any colour temperature you
or
1. Press the D
4
/ E
/ E
button to select User.
2. Press the G button and then D
/ E
3. Press the F
appropriate adjustments.
/ G
prefer.
button to make
button to select Red,
Press the EXIT button to return to normal TV
Green,
or
Blue.
viewing.
29
Picture
adjustment
Function
STATION
PSM
STATION
CSM
CSM
PICTURE G
TIME
Off
ACM
Contrast
90
Brightness
55
Colour
55
Sharpness
60
SOUND
TIME
SPECIAL
SPECIAL
SCREEN
SCREEN
Contrast
90
Brightness
55
Colour
55
Sharpness
60
Prev.
Menu
-
-
On
G
PICTURE
ACM
SOUND
PSM
XD is LG's
unique picture improving technology to display a real HD
source through an advanced digital
signal processing algorithm.
Press the MENU button and then D
1234
When
selecting PSM options
(Dynamic, Standard, or Mild),
XD automatically changes to On. If
XD setting is Off, PSM is automatically change to User and ACM
button to select the PICTURE
/ E
Press the G button and then D
/ E
button to select XD.
Press the G button and then D
/ E
button to select On
Press the EXIT button to return to normal TV
or
menu.
Off.
viewing.
function is not available.
-
XD function is not available in RGB
PC/HDMI PC mode.
ACM
STATI ON
(Active Colour Management)
PSM
STATION
CSM
CSM
PICTURE G
PICTURE
ACM
SOUND
TIME
PSM
Fleshtone
0
Contrast
Greentone
0
Brightness
Bluetone
0
ACM
Contrast
90
Brightness
55
Colour
55
Sharpness
60
SOUND
TIME
G
Colour
Sharpness
SPECIAL
SPECIAL
SCREEN
SCREEN
Menu
-
Adjust
the ACM to select the
desired skin colour
-
option.
ACM function is available in all
modes except RGB PC/HDMI PC
mode.
Press the MENU button and then D
123
45
30
Prev.
/ E
button to select the PICTURE
Press the G button and then D
/ E
button to select ACM
Press the G button and then D
/ E
button to select
or
/ G
button to make
appropriate adjustments.
Press the EXIT button to return to normal TV
.
Fleshtone, Greentone,
Bluetone.
Press the F
menu.
viewing.
sRGB
STATION
PSM
PSM
STATION
CSM
CSM
PICTURE G
PICTURE
ACM
SOUND
sRGB
Contrast
90
Brightness
55
SOUND
TIME
TIME
SPECIAL
SPECIAL
SCREEN
SCREEN
Contrast
90
Brightness
55
When the set
was
connected to
equipment with sRGB
function, it adjusted a colour difference to display the equal
image each other.
external
-
sRGB function is available in RGB
PC/HDMI PC mode.
Press the MENU button and then D
1234
button to select sRGB.
Press the G button and then D
/ E
button to select On
Press the EXIT button to return to normal TV
PSM
STATION
viewing.
Adjustment
PSM
ACM
Contrast
90
Brightness
55
Colour
55
Sharpness
60
SOUND
TIME
SPECIAL
SPECIAL
SCREEN
SCREEN
Contrast
90G
Brightness
55
Colour
55
Sharpness
60
Menu
You
Off.
PICTURE
ACM
-
or
menu.
CSM
PICTURE G
TIME
button to select the PICTURE
/ E
CSM
SOUND
/ E
Press the G button and then D
Manual Picture
STATION
Off
Prev.
Menu
-
On
G
adjust picture
Contrast, Brightness,
Colour, Sharpness and Tint
(NTSC only) to the levels you
prefer.
can
12
Prev.
Press the MENU button and then D
Press the G button and then D
/ E
/ E
button to select the PICTURE
button to select the desired
option (Contrast, Brightness, Colour,
or
3
Press the F
4
Press the EXIT button to return to normal TV
/ G
button to make
menu.
picture
Sharpness).
appropriate adjustments.
viewing.
Note
?
Only Contrast
and
Brightness
are
displayed
in PC mode.
31
Sound
Sound
adjustment
SSM
-
-
SSM lets you enjoy the best
sound without any special adjustment because the TV sets the
appropriate sound options based
on the program content.
SSM
Flat, Music, Movie, and Sports
are preset for good sound quality
at
the
and
factory
adjustable.
-
(Sound Status Memory)
You
can
also
to
adjust
menu
are
not
Flat
the SOUND
SSM.
use
1
Press the SSM button
setup option
as
to select the
repeatedly
shown below:
picture appearance
Flat, Music, Movie, Sports, or User.
SRS WOW
SSM
STATION
SSM
STATION
SRS WOW
SRS WOW
AVL
PICTURE
SOUND G
TIME
0
Treble
50
Bass
50
TV
Balance
SOUND
speaker
TIME
SPECIAL
SPECIAL
SCREEN
SCREEN
The
SRS
back the
input
mono
with
effects. It
WOW function
or
plays
stereo sound
the
dynamic surround
will provide rich and pro-
found sound tone.
-IfyousettheSRSWOWON,
Treble/Bass can not be adjusted.
0
Treble
50
Bass
50
TV
speaker
Menu
-
Off
AVL
PICTURE
Balance
Prev.
Press the MENU button and then D
1234
/ E
button to select the SOUND
Press the G button and then D
/ E
button to select SRS WOW.
Press the G button and then D
/ E
button to select On
Press the EXIT button to return to normal TV
is
a
trademark of SRS
technology
32
On
G
is
or
Off.
viewing.
Labs, Inc.
incorporated
under license from SRS
Labs, Inc.
menu.
AVL
STATION
SSM
(Auto Volume leveler)
STATI ON
SRS WOW
SRS WOW
PICTURE
AVL
PICTURE
Balance
SOUND G
TIME
50
Bass
50
AVL
SOUND
TIME
speaker
SPECIAL
SPECIAL
SCREEN
SCREEN
50
Bass
50
AVL
automatically keeps
on an
equal volume level even
change programmes.
if you
1234
/ E
button to select AVL
Press the G button and then D
/ E
button to select On
Press the EXIT button to return to normal TV
STATION
SSM
SOUND G
TIME
PICTURE
-
50
Bass
50
TIME
speaker
SPECIAL
SCREEN
SCREEN
the
When
sound to
suit your
situations.
adjusting sound options
(treble and bass) manually, SSM
is automatically changed to
User.
or
Off.
viewing.
SSM
AVL
50
Bass
50
TV
12
34
L
0G
Treble
R
speaker
Menu
taste and room
-
SOUND
SPECIAL
Adjust
.
Adjustment
Balance
0
Treble
TV
menu.
SRS WOW
AVL
Balance
button to select the SOUND
/ E
Press the G button and then D
SRS WOW
PICTURE
Prev.
Press the MENU button and then D
Manual Sound
STATION
Off
speaker
Menu
-
0
Treble
TV
On
G
Balance
0
Treble
TV
SSM
Prev.
Press the MENU button and then D
Press the G button and then D
option (Balance, Treble,
or
/ E
button to select the SOUND
menu.
button to select the desired sound
/ E
Bass).
Press the G button and then F
/ G
button to make desired
Press the EXIT button to return to normal TV
adjustment.
viewing.
33
Sound
Sound
adjustment
TV
STATION
STATION
SSM
PICTURE
AVL
Balance
SOUND G
TIME
50
Bass
50
AVL
Balance
0
Treble
TV
SSM
SRS WOW
SRS WOW
PICTURE
Speaker
SOUND
TIME
speaker
0
Treble
50
Bass
50
TV
Speaker
GOn
Off
-
You
SPECIAL
SPECIAL
SCREEN
SCREEN
can
Menu
adjust
internal
speaker
status.
-
If you want to
your external hifi stereo system, turn off the internal speakers of the set.
34
use
Prev.
Press the MENU button and then D
1234
/ E
button to select the SOUND
menu.
Press the G button and then D
/ E
button to select TV
Speaker.
Press the G button and then D
/ E
button to select On
or
Press the EXIT button to return to normal TV
viewing.
Off.
I/II
A Stereo/Dual
When
reception
programme is selected, the sound information for the station appears
after the programme number and station name disappear.
?
I/II
a
Broadcast
On Screen
Mono
MONO
Stereo
STEREO
Dual
DUAL I
Display
Mono sound selection
In stereo
reception
if the stereo
signal
is
pressing
the I/II button twice. In
mono
reception
weak, you
the
To switch back to stereo, press the I/II button twice
can
switch to
depth
again.
by
improved.
mono
of sound is
selection for dual
language broadcast
If a programme is received in two languages (dual language), you can switch
DUAL I, DUAL II or DUAL I+II by pressing the I/II button repeatedly.
DUAL I sends the primary broadcast language to the loudspeakers.
DUAL II sends the secondary broadcast language to the loud-speakers.
DUAL I+II sends a separate language to each loudspeaker.
?
Language
A NICAM
reception (This
to
feature is not available in all countries.)
If your set is equipped with the receiver for NICAM reception, the high quality
NICAM (Near Instantaneous Companding Audio Multiplex) digital sound can be
received.
Sound
output
follows
by pressing
can
be selected
the I/II
1. When NICAM mono is
according to the type
button repeatedly.
received, you
can
of received broadcast
select NICAM MONO
or
as
FM
MONO.
2. When NICAM stereo is
3.
received, you can select NICAM STEREO or FM
MONO. If the stereo signal is weak, switch to FM mono.
When NICAM dual is received, you can select NICAM DUAL I, NICAM
DUAL II
display
A Sound
or
NICAM DUAL I+II
MONO appears
on
or
the
MONO. When FM
mono
is selected the
screen.
output selection
In
AV, S-video, Component1, Component2, RGB-DTV (or RGB-PC),
HDMI-DTV (or HDMI-PC) mode, you can select output sound for the left and
right loud-speakers. Repeatedly press the I/II button to select the sound output.
L+R
loud-speaker and audio signal from audio R input is sent to right loud-speaker.
L+L : Audio signal from audio L input is sent to left and right loud-speakers.
R+R : Audio signal from audio R input is sent to left and right loud-speakers.
:
Audio
signal
from audio L
input
is sent to left
35
ime Menu
Time
Clock
Clock
STATION
STATI ON
Off time
Auto
Clock
G
PICTURE
sleep
sleep
Auto
SOUND
SOUND
TIME G
TIME
SPECIAL
SPECIAL
SCREEN
SCREEN
You must set the time
before
-
using
If current time
-
On time
Prev.
Menu
-
--:-
Off time
On time
PICTURE
Setup
correctly
on/off time function.
setting is
erased by
power failure or the set is
unplugged, reset the clock.
a
Press the MENU button and then D
12345
/ E
button to select the TIME
Press the G button and then D
/ E
button to select Clock.
Press the G button and then D
/ E
button to set the hour.
Press the G button and then D
/ E
button to set the minutes.
Press the EXIT button to return to normal TV
menu.
viewing.
On/Off time
Clock
STATION
STATION
Off time
Off time
On time
PICTURE
Auto
Clock
PICTURE
On time
Off
sleep
Auto
sleep
On
G
00:00
SOUND
SOUND
Volume
TIME G
TIME
SPECIAL
SPECIAL
SCREEN
SCREEN
Programme
Menu
-
The off time
the set to
automatically switches
standby at the preset
time.
7
0
Prev.
Press the MENU button and then D
123
456
30
Press the G button and then D
/ E
/ E
button to select the TIME
button to select Off time
or
menu.
On time.
Press the G button and then D / E button to select On.
?
To cancel On/Off time function, press the D / E button to select Off.
Press the G button and then D
/ E
button to set the hour.
Press the G button and then D
/ E
button to set the minutes.
Press the G button and then D
volume level and programme number.
Only On time function;
Press the EXIT button to return to normal TV
/ E
button to
viewing.
Note
In the event of power interruption (disconnection or power failure), the clock must be reset.
b. Two hours after the set is switched on by the on time function it will automatically switch back to
a.
mode unless
Once the On
button has been pressed.
c.
or Off Time is set, these functions operate daily at the preset time.
d. Off Time function overrides On Time function if they are set to the same time.
e. The set must be in standby mode for the On Time to work.
36
a
standby
adjust
Auto
STATION
Clock
Clock
STATION
Off time
PICTURE
Off time
On time
Auto
Sleep
On time
PICTURE
sleep
sleep
Auto
SOUND
On
G
Off
SOUND
TIME G
TIME
SPECIAL
SPECIAL
SCREEN
SCREEN
Menu
-Ifsettoonandthereisnoinput
signal, the TV turns off automatically after 10 minutes.
Prev.
Press the MENU button and then D
1234
/ E
button to select the TIME
Press the G button and then D
/ E
button to select Auto
Press the G button and then D
/ E
button to select On
Press the EXIT button to return to normal TV
menu.
sleep.
or
Off.
viewing.
Timer
Sleep
zz
-
SLEEP
1
Press the SLEEP button
the
'
timer
-
Min
repeatedly
to select the number of minutes. First
'
-
option appears on the screen, followed by the following sleep
options: 10, 20, 30, 60, 90, 120, 180, and 240 minutes.
-
-
The timer
234
-
begins
To view the
remaining sleep time,
To cancel the
display
'
'
-
-
to count down from the number of minutes selected.
-
press the SLEEP button
sleep time, repeatedly
once.
press the SLEEP button until the
appears.
Note
press the SLEEP button once.
b. When you switch the set off, the set releases the preset sleep time.
a.
To view the
remaining sleep time,
37
Special
Menu
Input
STATI ON
Input
STATI ON
Language
PICTURE
Child lock
PICTURE
Set ID
SOUND
Input
Language
TV
Child lock
AV
Set ID
S-Video
SOUND
Demo
TIME
G
Demo
TIME
Component
1
Component
2
RGB
PC
HDMI
SPECIAL G
SPECIAL
SCREEN
SCREEN
Prev.
Menu
Alternatively you can select the TV,
AV, S-video, Component1,
Component2, RGB-DTV (or RGBPC), or HDMI-DTV (or HDMI-PC)
mode by pressing the INPUT button.
-
PC
1
Press the MENU button and then D
/ E
2
Press the G button and then D
button to select
3
Press the G
button and then
/ E
use
button to select the SPECIAL
the D
Input.
button to select
/ E
menu.
TV, AV, S
-
video, Component1, Component2, RGB-DTV (or RGB-PC), or
HDMI-DTV (or HDMI-PC).
Press the F / G button to select the RGB-DTV (or RGB-PC), or HDMI-DTV
(or HDMI-PC).
4
Press the EXIT button to return to normal TV
viewing.
Child Lock
STATION
Input
STATION
Language
PICTURE
Language
Child lock
PICTURE
Set ID
Child lock
TIME
TIME
SPECIAL G
SPECIAL
SCREEN
SCREEN
The TV can be set
so
that the remote
1
control handset is needed to control it.
This feature
can
unauthorized
be used to prevent
viewing.
This set
programmed
b. In Child lock
TV, INPUT, PR
c.
38
Press the MENU button and then D / E button to select the SPECIAL
Press the G button and then D
set is turned
/ E
button to select On
Press the EXIT button to return to normal TV
to remember which
'On', if the
Prev.
menu.
Press the G button and then D / E button to select Child lock.
234
Note
a.
Off
Demo
SOUND
Menu
-
On
G
Set ID
Demo
SOUND
Input
option
it
was
last set to
even
off, press the POWER, INPUT,
or
Off.
viewing.
if you turn the set off.
PR D / E button on the set
or
POWER,
D / E or NUMBER buttons on the remote control.
With the Child lock On, the display 'Child lock on' appears
pressed while viewing the set.
on
the
screen
if any button
on
the front
panel
is
Demo
STATION
Input
STATION
Language
Language
PICTURE
Child lock
PICTURE
Child lock
Set ID
Set ID
SOUND
Input
SOUND
Demo
TIME
TIME
SPECIAL G
SPECIAL
SCREEN
SCREEN
Demo
To Start
G
TM
Menu
TM
Off
Prev.
Menu
-
Use
it
to
see
the
between XD demo
difference
on
Demo off.
-
Press the MENU button and then D
and XD
XD Demo function is not avail-
able in RGB PC/HDMI PC mode.
1234
On
Press the G button and then D
/ E
/ E
Exit
button to select the SPECIAL
menu.
button to select XD Demo.
Press the G button to start XD Demo.
To
stop XD Demo, press the EXIT button.
39
Screen Menu
Auto
STATION
config.
Auto
Manual
PICTURE
Configure
STATION
Auto
PICTURE
XGA Mode
config.
Manual config.
config.
XGA Mode
ARC
ARC
SOUND
SOUND
Zoom +/-
Zoom +/-
Position
Position
TIME
TIME
Cinema
Cinema
NR
NR
SPECIAL
SPECIAL
SCREEN
-
Automatically adjusts picture position
and minimizes image shaking.
if the image is still
not correct, your TV is functioning
properly but needs further adjust-
After
Prev.
Menu
Auto config. function is available
in RGB PC mode only.
-
Reset
Reset
SCREEN G
-
To set
G
adjustment,
1
Press the MENU button and then
SCREEN
23
use
Press the G button to start Auto
If the
/ E
button to select the
menu.
Press the G button and then
?
D
use
of the
position
image
D / E button to select Auto
config..
config..
is still not correct,
try Auto adjustment
again.
ment.
-
Automatically adjusts the screen
position, clock, and phase. (The
displayed image will disappear for
a few seconds while Auto-configuration is in progress.)
Manual
Auto
STATION
Manual
config.
XGA Mode
PICTURE
config.
Manual config.
Auto
STATION
config.
PICTURE
ARC
SOUND
Zoom +/-
SOUND
TIME
Cinema
Manual
SPECIAL
Reset
config.
function is avail-
or
If the
picture isn't clear after auto
adjustment and especially that
characters are still trembling, adjust
the picture phase manually.
-
In
H-Position
0
Zoom +/-
V-Position
0
Reset
screen
123
function is not available.
use
Press the G button and then
?
?
use
D / E button to select the SCREEN menu.
D / E button to select Manual config..
use
D / E button to select
or
up/down
45
Phase, Clock, H-
V-Position.
Phase : This function allows you to remove any horizontal noise and clear or
sharpen the image of characters.
Clock : This function is to minimize any vertical bars or stripes visible on the
screen background. And the horizontal screen size will also change.
H-Position / V-Position : This function is to adjust picture to left/right and
Position,
size, adjust
H-position/V-Position
Prev.
Press the G button and then
Component [480i, 576i]
mode,
40
ARC
Press the MENU button and then
?
To correct the
Clock.
0
Menu
Component
(480p,576p,720p,1080i) mode.
-
Clock
SCREEN
able in RGB PC
-
XGA Mode
NR
SCREEN G
-
10
Cinema
NR
SPECIAL
Phase
G
Position
Position
TIME
Configure
Press the F
/ G
button to make
as
you
prefer.
appropriate adjustments.
Press the EXIT button to return to normal TV
viewing.
XGA Mode
config.
Auto
STATION
Manual
STATION
PICTURE
SOUND
Zoom +/-
TIME
Cinema
SPECIAL
Reset
XGA Mode function is available in
RGB PC mode and XGA/WXGA
For
1360x768
Zoom +/-
1366x768
Cinema
Reset
Prev.
Menu
mode(60Hz) only.
-
1280x768
SCREEN
SCREEN G
-
1024x768
G
NR
NR
SPECIAL
XGA Mode
Position
Position
TIME
config.
ARC
ARC
SOUND
config.
Manual
config.
XGA Mode
PICTURE
Auto
improved or better picture quality, select the same mode
corresponding to computer resolumore
1
23
Press the MENU button and then
use
Press the G button and then
use
D / E button to select XGA Mode.
Press the G button and then
use
D / E button to select desired mode.
From this
point
on, the
D / E button to select the SCREEN menu.
adjustment
starts.
tion.
Picture Size Zoom
Auto
STATION
STATION
config.
Manual
PICTURE
SOUND
Zoom +/-
TIME
Cinema
SPECIAL
Reset
-
enlarging or reducing the picture,
the screen may be display unnatural
picture.
1
the
23
picture position with the D / E / F
buttons in enlarged picture mode.
4
can
G
F
G
Cinema
Reset
Menu
When
You
Zoom +/-
%
SCREEN
SCREEN G
-
100
NR
NR
SPECIAL
XGA Mode
Position
Position
TIME
config.
ARC
ARC
SOUND
config.
Manual
config.
XGA Mode
PICTURE
Auto
also
enlarge
or reduce
the pic-
ture size with ZOOM /ZOOM +
-
remote control and then
on
adjust
the
Prev.
Press the MENU button and then
use
Press the G button and then
D / E button to select Zoom
use
Press the G button and then F
?
The
adjustment range
of
/ G
zoom
D / E button to select the SCREEN menu.
button to
enlarge
or
+
/
reduce the
-.
picture
size.
is 100~300%.
main
/G
-
Press the EXIT button to return to normal TV
viewing.
Zoom + / function is not available
in RGB PC mode.
-
ZOOM
-
ZOOM +
41
Screen Menu
Picture format
(ARC)
Spectacle
-
You
watch TV
can
(This
feature is not
,
Video, S-Video in various picture formats; Spectacle, Full
available in all countries.), Original, 4:3, 16:9, 14:9, Zoom.
press the ARC button to select your desired
also use the SCREEN menu to adjust ARC.
Repeatedly
ARC
-
You
can
picture
format.
Spectacle
When your TV receives the wide screen signal, it will lead you to
horizontally, in a nonlinear proportion, to fill the entire screen.
adjust
the
picture
Full (This feature is not available in all countries.)
When your TV receives the wide
horizontally
or
in
vertically,
linear
a
signal,
proportion, to
screen
it will lead you to
fill the entire
adjust the picture
screen fully.
Original
When your TV receives the wide
picture format to be sent.
(Without TELETEXT)
screen
signal,
it will be
automatically changed to the
4:3
This
picture
format is 4 to 3 of
general
TV.
16:9
You
right
(the picture
format of
16:9)
or
TV programme
general
the 16:9 mode.
through
The
the cinema
enjoy
can
screen
16:9 is viewed
so
that the
can
enjoy
screen
just
like that but the
screen
4:3 is
magnified
to the left and
16:9 is full.
14:9
You
the
picture
format of 14:9
or
general
TV programme
through
the 14:9
mode.
The
ARC
screen
14:9 is viewed
lower and left /
just
like that the
screen
4:3 is
magnified
to the upper /
right.
Zoom
You
can
The
screen
screen
enjoy
the cinema in
4:3 is
magnified
a
vast
screen
through
the Zoom mode.
to the upper / lower and left /
16:9 is full. The bottom and
right
sides
so
that the
top of the picture may be lost.
Note
a.
In PC
b.
In
(With TELETEXT)
aspect ratios
c.
42
(RGB or HDMI) mode only 16:9 and 4:3 aspect ratios are available.
Component, RGB DTV, HDMI DTV mode only 4:3, 16:9 and Zoom
There
are
might be
available.
uncomfortable in full mode. Then
change
into other mode.
Screen Position
STATION
config.
Auto
STATION
Manual
Manual
config.
PICTURE
XGA Mode
PICTURE
SOUND
Zoom +/-
TIME
SPECIAL
Reset
-
the
is
enlarged, you can
position of the picture.
Position function is not available in
RGB PC mode.
-
Position function is available after
adjusting
E
Cinema
Reset
Prev.
Menu
screen
change
G
SCREEN
SCREEN G
When
F
G
NR
NR
-
Zoom +/-
Position
Cinema
SPECIAL
XGA Mode
D
Position
TIME
config.
ARC
ARC
SOUND
config.
Auto
Zoom
+
/
.
1
Press the MENU button and then
2
Press the G button and then
34
use
D / E button to select the SCREEN menu.
D / E button to select Position.
use
Press the G button and then D / E / F / G button to
Press the EXIT button to return to normal TV
adjust
the
position.
viewing.
Cinema
STATI ON
Auto
config.
Manual
PICTURE
STATION
Manual
config.
XGA Mode
PICTURE
SOUND
Zoom +/-
TIME
Cinema
SPECIAL
Reset
-
appearance.
Cinema function is available in
TV, AV S-Video,
,
(480i, 576i))
G
On
Off
Reset
Menu
When you watch the movie, this
function adjusts the set to the best
picture
Cinema
SCREEN
SCREEN G
-
Zoom +/-
NR
NR
SPECIAL
XGA Mode
Position
Position
TIME
config.
ARC
ARC
SOUND
config.
Auto
mode
or
Component
1
234
Prev.
Press the MENU button and then
use
Press the G button and then
D / E button to select Cinema.
use
Press the G button and then D
/ E
D / E button to select the SCREEN menu.
button to select On
Press the EXIT button to return to normal TV
or
Off.
viewing.
43
Screen
Screen Menu
NR
STATI ON
Auto
config.
Manual
PICTURE
(Noise Reduction)
Manual
config.
XGA Mode
ARC
Zoom +/-
SOUND
Zoom +/-
Position
Position
TIME
TIME
Cinema
Cinema
NR
NR
SPECIAL
SPECIAL
Reset
-
-
You can select 3D NR or MPEG NR
to reduce the picture noise which
may appear on the screen during
watching the TV.
This function is not available for use
in RGB PC, HDMI PC mode.
3D NR is not available for use in
Component, RGB DTV, HDMI
DTV mode.
Reset
Menu
1
3D NR
0
MPEG NR
0
Prev.
Press the MENU button and then
SCREEN
Press the G button and then
MPEG NR.
4
Press the F
Press the G
?
The
?
The
use
D
/ E
button to select the
menu.
23
5
44
G
SCREEN
SCREEN G
-
config.
XGA Mode
PICTURE
ARC
SOUND
config.
Auto
STATION
use
button and then
/ G
button to make
adjustment
adjustment
D / E button to select NR.
use
D
/ E
button to select 3D NR
appropriate adjustments.
range of 3D NR is 0~2.
range of MPEG NR is 0~15.
Press the EXIT button to return to normal TV
viewing.
or
Reset to
STATI ON
Auto
STATION
config.
Manual
PICTURE
original factory
XGA Mode
PICTURE
SOUND
Zoom +/-
TIME
Cinema
SPECIAL
Reset
value.
Reset
Menu
This function
To
Cinema
SCREEN
1
mode.
Zoom +/-
NR
SCREEN G
-
XGA Mode
Position
NR
SPECIAL
config.
ARC
Position
TIME
(Initializing)
config.
Manual
config.
ARC
SOUND
Auto
value
operates
initialize
the
in
adjusted
23
Prev.
Press the MENU button and then
SCREEN
every
To set
G
use
D
/ E
button to select the
menu.
Press the G button and then
use
D / E button to select Reset.
Press the G button to start Reset.
The
display
OK will appear.
45
eletext (This
feature
Teletext
T
(This
Teletext
(or TOP text)
is
an
optional function,
therefore
is not available in all
only
a
set with the teletext
system
can
countries.)
countries.)
receive the teletext broad-
cast.
Teletext is
a
free service broadcast
sion programmes, share
sists of
a
are more
and many other
prices
The teletext decoder of this TV
most TV stations which
by
can
gives up-to-the-minute
information
on
news,
weather, televi-
topics.
support the SIMPLE, TOP and FASTEXT systems. SIMPLE (standard teletext)
con-
number of pages which are selected by directly entering the corresponding page number. TOP and FASTEXT
modern methods allowing quick and easy selection of teletext information.
Press the TEXT button to switch to teletext. The initial page or last page appears on the screen.
Two page numbers, TV station name, date and time are displayed on the screen headline. The first page number indicates
your selection, while the second shows the current page displayed.
Press the TEXT button to switch off teletext. The
A
Page
previous
mode reappears.
selection
1. Enter the desired page number as a three digit number with the NUMBER buttons. If during selection you press
number, you must complete the three digit number and then reenter the correct page number.
2. The PR D / E buttons
A
Programming
a
can
be used to select the
preceding
or
following
or
FASTEXT
mode, press the
Four teletext page numbers of your choice can be colour coded and
corresponding coloured button on the remote control handset.
1. Press
a
2.
the NUMBER
page.
M button to switch to LIST mode.
easily
selected
by pressing
buttons, select the page you wish
4. The three other coloured buttons
user
the
coloured button.
to programme.
3. Press the OK button. Then the selected page is stored as the selected page number
you can select this page with the same coloured button.
The
wrong
colour button in LIST mode
If the TV is in SIMPLE text, TOP text
Using
a
guide displays
four
are
programmed
by blinking
once.
From
now
on,
in this way.
fields-red, green, yellow and blue
at the bottom of the
screen.
The
yellow
field denotes the
next group and the blue field indicates the next block.
A Block / group / page selection
1. With the blue button you
2. Use the yellow button to
progress from block to block.
proceed to the next group with automatic overflow to the next block.
3. With the green button you can proceed to the next existing page with automatic overflow to the next group.
the PR D button can be used.
4. The red button
Alternatively
permits
can
to return to
the PR E button
can
previous
Alternatively
selection.
be used.
A Direct page selection
Corresponding
to the SIMPLE teletext
BER buttons in TOP mode.
46
mode, you
can
select
a
page
by entering
it
as a
three
digit
number
using
the NUM-
The teletext pages are colour coded
corresponding coloured button.
A
1. Press the
3.
the bottom of the
screen
and
are
selected
by pressing
the
selection
Page
2. You
along
button to select the index page.
select the pages which are colour coded
can
i
Corresponding
to the SIMPLE teletext
mode, you
along
can
the bottom line with the
select
a
page
by entering
same
coloured buttons.
its three
digit
page number with
the NUMBER buttons in FASTEXT mode.
4. The PR
?
D / E
buttons
be used to select the
can
preceding
or
following.
REVEAL
Press this button to
Press this button
display concealed information, such as solutions
again to remove the information from the display.
of riddles
or
puzzles.
SIZE
Selects double
Press this
Press this
Press this
height text.
button to enlarge the top half of the page.
button again to enlarge the bottom half of the
button again to return to the normal display.
page.
UPDATE
Displays
the TV
top left hand
picture
corner
on
of the
the
screen
screen.
while
When
waiting for the new teletext
the updated page is available
page. The display
then display
will appear at the
will change to the page
number.
Press this button to view the
updated
teletext page.
HOLD
the automatic page change which will occur if a teletext page consists of 2 or more sub pages. The number of
sub pages and the sub page displayed is, usually, shown on the screen below the time. When this button is pressed
Stops
the
stop symbol is displayed
To continue press this button
at the
top left-hand
corner
of the
screen
and the automatic page
change
is inhibited.
again.
MIX
the teletext pages superimposed on the TV
To switch the TV picture off press this button again.
Displays
picture.
TIME
When
viewing a TV programme, press this button to display the time at the top right hand corner of the screen. Press
this button again to remove the display. In the teletext mode, press this button to select a sub page number. The sub
page number is displayed at the bottom of the screen. To hold or change the sub page, press the RED/GREEN,
F / G
or
Press
again
NUMBER buttons.
to exit this function.
47
External Control
Control Device
Setup
Connect the RS-232C
-
and control the TV's
Connect the serial
-
input jack to an external
functions externally.
port of the control device
RS-232C connection cable is not
-
RS-232C
supplied
; RS-232C
control device
to the RS-232C
(such
jack
as a
on
computer
the TV back
or an
A/V control
system)
panel.
with the TV.
Setup
PC
Type
Type
of
of Connector;
9-Pin Male
Male
Connector; D-Sub 9-Pin
1
No.
Pin
1
No connection
2
RXD
3
TXD
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
9
name
5
(Receive data)
(Transmit data)
(DTE side ready)
(DCE side ready)
(Ready to send)
(Clear to send)
9
6
No Connection
RS-232C
Configurations
Configurations
3-Wire
Configurations
(Not standard)
7-Wire
Configurations
(Standard RS-232C cable)
PC
PC
TV
RXD
3
TXD
RXD
3
TXD
TXD
2
RXD
TXD
2
RXD
5
GND
GND
5
GND
6
DSR
DTR
4
DTR
4
DTR
DSR
6
DSR
8
CTS
RTS
7
RTS
7
RTS
CTS
8
CTS
GND
DTR
DSR
RTS
CTS
2354678
D-Sub 9
48
TV
D-Sub 9
2354678
D-Sub 9
D-Sub 9
Reference
External Control
Control Device
Setup
; RS-232C
Set
Set ID
Use this function to
-
Refer to 'Real Data
-
specify a monitor ID number.
Mapping 1'. See page 50.
Input
STATION
Language
1. Press the MENU button and then
Special
button to select the
use D / E
Set ID
menu.
SOUND
2. Press the G button and then
use D / E
3. Press the G button and then
use
F / G
G
Demo
button to select Set ID.
button to
to choose the desired monitor ID number. The
adjust Set ID
adjustment range
TIME
SPECIAL
ofSetIDis1~99.
4. Press the OK button to
1
Child lock
PICTURE
save.
SCREEN
Prev.
Menu
ransmission /
T
Transmission
Baud rate
:
Data
9600
[Command1][Command2][ ][Set ID][ ][Data][Cr]
bps (UART)
8 bits
length
Parity : None
?Stopbit:1bit
?
:
*
*
?
?
*
*
Communication code
:
ASCII code
[Command 1]: First command. (k, x or m)
[Command 2]: Second command.
[Set ID]: You can adjust the set ID to choose desired monitor
ID number in Special menu. Adjustment range is 1
99. When selecting Set ID '0', every connected
~
Use
a
crossed
(reverse)
cable.
TV set is controlled. Set ID is indicated
*
*
ka0~1
Input Select (Main Picture)
Aspect Ratio
x
b
[DATA]:
To transmit command data.
[Cr]: Carriage
Return
ASCII code '0x0D'
*
02.
*
[
]:
ASCII code
'space (0x20)'
kc0~6
OK Acknowledgement
04. Screen Mute
kd0~1
[Command2][ ][Set ID][ ][OK][Data][x]
05. Volume Mute
ke0~1
03.
06. Volume Control
kf0~64
07. Contrast
kg0~64
08.
kh0~64
Brightness
09. Colour
ki0~64
10. Tint
kj0~64
11.
12. OSD Select
13.
Key
*
(acknowledgement)
this format when
normal data. At this
time, if the
[Command2][ ][Set ID][ ][NG][Data][x]
km0~1
14. Balance
kt0~64
15. Programme Select (Main TV Input)
m
16.
m
Key
a
c
0
63
~
The Monitor transmits ACK
(acknowledgement)
this format when
abnormal data from non-viable
functions
KeyCode
Data
Refer to '02
on
Error Acknowledgement
*
:
receiving
based
mode, it indicates present status data. If
the data is data write mode, it returns the data of the PC
computer.
kl0~1
Lock
The Monitor transmits ACK
data is data read
kk0~64
Sharpness
decimal
Transmit 'FF' data to read status of command.
COMMAND COMMAND DATA
2
1
(Hexa)
01. Power
as
(1~99)on menu and as Hexa decimal (0x0~0x63)
on transmission/receiving protocol.
Command
Command Reference List
*
Protocol
Transmission
Communication
Communication Parameters
?
Receiving
Input
Select'
on
page 50.
1:
or
communication
Illegal
2: not
receiving
based
on
errors.
Code
support function
Error messages
1. Illegal ID : If Wrong
?
2.
3.
4.
or no
ID in the command is written.
B_TokenLength !=2 : If the first argument of the command does not
equals to 2.
Error ==TOKEN_ERROR : If some Special character or Numeric
are written to the first argument of the command or wrong Space
position is written to the first argument of the command.
Illegal Opcodes : If the Wrong Alphabet is written to the first argument of the command.
5.
Illegal Params : If the Wrong parameter is supplied to the end of the
command line (means that value of the parameter that is not supported).
49
Reference
External Control
Control Device
01. Power On
Setup
; RS-232C
04. Screen Mute
(Command:d)
G To control Power On/Off of the TV.
G To select
mute on/off.
Transmission
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
[k][d][ ][Set ID][ ][Data][Cr]
Data
0
(Command:a)
Power Off
:
Data
:PowerOn
1
Acknowledgement
screen
0
:
Screen mute off
1
:
Screen mute
on
(Picture on)
(Picture off)
Acknowledgement
[a][ ][Set ID][ ][OK][Data][x]
[d][ ][Set ID][ ][OK][Data][x]
G To show Power On/Off.
05. Volume Mute
Transmission
(Command:e)
G To control volume
[k][a][ ][Set ID][ ][FF][Cr]
You
can
also
mute on/off.
mute
adjust
using
the MUTE button
on
remote control.
Acknowledgement
Transmission
[a][ ][Set ID][ ][OK][Data][x]
Data
02.
0
Power Off
:
Input
Select
G To select input
You
ton
(Command:b) (Main
source
also select
can
an
[k][e][ ][Set ID][ ][Data][Cr]
:PowerOn
1
Picture
Data
Input)
for the TV.
input
source
using
:
Volume mute
1
:
Volume mute off
on
(Volume off)
(Volume on)
Acknowledgement
the INPUT but-
the TV's remote control.
on
0
[e][ ][Set ID][ ][OK][Data][x]
Transmission
06. Volume Control
[x][b][ ][Set ID][ ][Data][Cr]
Data
10
:TV
50or60:RGBPC
20
:AV
51or61:RGBDTV
30
:
S-Video
40
:
41
:
Component
Component
1
90
:
HDMI PC
91
:
HDMI DTV
G To adjust volume.
You
You
Screen
Data
Min: 0
?
(Command:c) (Main picture format)
screen
Max: 64
Refer to 'Real
(transmit by
data mapping
format.
1'
as
code)
shown below.
also
07. Contrast
menu.
G To adjust
You
0
:
Normal
1
:
Wide
(4:3)
(16:9)
screen
screen
4
:
Spectacle
5
:
Full(This feature
In PC mode
only
6
16:9 and 4:3
Acknowledgement
screen
also
contrast.
adjust
contrast in the Picture
menu.
:
aspect ratios
[k][g][ ][Set ID][ ][Data][Cr]
is not
available in all countries.
3:Zoom
can
(Command:g)
Transmission
2:14:9
)
Data
Min: 0
?
Original
are
available.
~
Max: 64
Refer to 'Real
(transmit by
data mapping
Acknowledgement
[g][ ][Set ID][ ][OK][Data][x]
[c][ ][Set ID][ ][OK][Data][x]
*
Real data
0
mapping
:Step0
A:Step10
F:Step15
10:Step16
64
:
100
Step
*Tint:R50~G50
*
50
Hexadecimal
[f][ ][Set ID][ ][OK][Data][x]
[k][c][ ][Set ID][ ][Data][Cr]
*
~
Acknowledgement
Transmission
Data
volume with the volume buttons
2
adjust the screen format using the ARC
(Aspect Ratio Control) button on remote control or in the
can
adjust
[k][f][ ][Set ID][ ][Data][Cr]
Ratio
G To adjust the
also
Transmission
[b][ ][Set ID][ ][OK][Data][x]
Aspect
can
remote control.
on
Acknowledgement
03.
(Command:f)
Balance
:
L50
~
R50
Hexadecimal
1'
as
code)
shown below.
08.
13.
Brightness (Command:h)
G To adjust
You
can
brightness.
adjust brightness
(Command:m)
G To lock the side panel controls
screen
also
Lock
Key
in the Picture
menu.
on
the TV.
Transmission
Transmission
[k][m][ ][Set ID][ ][Data][Cr]
[k][h][ ][Set ID][ ][Data][Cr]
Data
Min: 0
?
~
Data
Max: 64
Hexadecimal
Refer to 'Real
(transmit by
data mapping
code)
1'. See page 50.
Acknowledgement
G To adjust the
You
can
also
If you're not using the side panel controls on the TV, use
this mode. When main power is on/off, remote control
lock is released.
14. Balance
screen
colour.
adjust
colour in the Picture
(Command:t)
G To adjust balance.
menu.
Transmission
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
[k][t][ ][Set ID][ ][Data][Cr]
Data
Min: 0
?
Max: 64
~
Refer to 'Real
(transmit by
data mapping
Hexadecimal
code)
1'. See page 50.
Data
?
Min: 0
~
Max: 64
Refer to 'Real data
(transmit by Hexadecimal code)
mapping 1'. See page 50.
Acknowledgement
Acknowledgement
[i][ ][Set ID][ ][OK][Data][x]
[t][ ][Set ID][ ][OK][Data][x]
10. Tint
(Command:j)
G To adjust the
You
can
also
M
screen
tint.(NTSC
input only)
adjust
tint in the Picture
15.
menu.
Programme Select (Command:m a) (Main
Transmission
G Tune channel
[k][j][ ][Set ID][ ][Data][Cr]
Transmission
Data
Min: 0
?
Max: 64
~
Refer to 'Real
(transmit by
data mapping
Hexadecimal
code)
1'. See page 50.
to
following Physical/major/minor
[j][ ][Set ID][ ][OK][Data][x]
11.
Acknowledgement
~
Sharpness (Command:k)
sharpness.
adjust sharpness in
screen
Transmission
[a][ ][Set ID][ ][OK][Data0][x]
[a][ ][Set ID][ ][NG][Data0][x]
[k][k][ ][Set ID][ ][Data][Cr]
16.
Data
can
also
Min: 0
?
~
Max: 64
Refer to 'Real
(transmit by
data mapping
the Picture
menu.
number.
Hexadecimal
code)
1'. See page 50.
G To send IR
remote
key
[k][ ][Set ID][ ][OK][Data][x]
[m][c][ ][Set ID][ ][Data][Cr]
G To select OSD (On Screen Display)
Data:
mute on/off.
Transmission
code)
1'. See page 50.
code.
Acknowledgement
(Command:l)
Hexadecimal
Key (Command:m c)
Transmission
12. OSD Select
Input)
Data0:
Acknowledgement
G To adjust the
TV
[m][a][ ][Set ID][ ][Data0][Cr]
Programme Number
Min : 0
Max : 63(transmit by
?
Refer to 'Real data mapping
You
on
[m][ ][Set ID][ ][OK][Data][x]
?
(Command:i)
1: Lock
Acknowledgement
[h][ ][Set ID][ ][OK][Data][x]
9. Colour
0: Lock off
Key
code
(Refer
to
P.53)
Acknowledgement
[c][ ][Set ID][ ][OK][Data][x]
[k][l][ ][Set ID][ ][Data][Cr]
Data
0: OSD mute
on
1: OSD mute off
Acknowledgement
[l][ ][Set ID][ ][OK][Data][x]
51
Reference
IR codes
codes
G
Connect your wired remote control to the Remote Control
port
on
the TV.
G Output waveform
Single pulse,
modulated with 37.917KHz
at 455KHz
signal
TC
Carrier
frequency
FCAR
1/TC
Duty
T1
=
ratio
=
fOSC/12
T1/TC
=
1/3
=
G Configuration of frame
?
1st frame
Lead
Low
High
code
custom code
custom code
Data code
Data code
C0 C1C2C3C4C5C6C7C0C1C2C3C4C5C6C7D0D1D2D3D4D5D6D7D0D1D2D3D4D5D6D7
?
Repeat
frame
Repeat
code
Tf
G Lead code
9ms
4.5
ms
0.55
G Repeat code
ms
9ms
2.25
ms
G Bit description
?
?
Bit "0"
0.56
0.56
ms
1.12
G Frame interval
:
Bit "1"
2.24
ms
Tf
The waveform is transmitted
Tf
as
long
as a
key
is
depressed.
Tf
Tf=108ms @455KHz
52
ms
ms
IR codes
codes
0F
TV
Remote Control Button
08
POWER
Remote Control Button
0B
INPUT
Remote Control Button
C4
POWER ON
Discrete IR Code
C5
POWER OFF
Discrete IR Code
5D
ZOOM-
Remote Control Button
5C
ZOOM+
Remote Control Button
0E
SLEEP
Remote Control Button
20
TEXT(This
52
SSM
Remote Control Button
4D
PSM
Remote Control Button
0A
I/II
Remote Control Button
43
MENU
Remote Control Button
79
ARC
Remote Control Button
5B
EXIT
Remote Control Button
07
F
Remote Control Button
06
G
Remote Control Button
40
D
Remote Control Button
41
E
Remote Control Button
44
OK
Remote Control Button
72
RED
Remote Control Button
71
GREEN
Remote Control Button
63
YELLOW
Remote Control Button
61
BLUE
Remote Control Button
02
VOL D
Remote Control Button
03
VOL E
Remote Control Button
00
PRD
Remote Control Button
01
PRE
Remote Control Button
09
MUTE
Remote Control Button
53
LIST
Remote Control Button
10~19
Number
1E
FAVOURITE
Remote Control Button
1A
Q.VIEW
Remote Control Button
64
SIZE
Remote Control Button
62
UPDATE
Remote Control Button
70
INDEX(This feature is not available in all countries.)
HOLD(This feature is not available in all countries.)
TIME(This feature is not available in all countries.)
REVEAL(This feature is not available in all countries.)
MIX(This feature is not available in all countries.)
MODE(This feature is not available in all countries.)
Remote Control Button
65
26
2A
24
22
feature is not available in all
Key
countries.)
0~9
(Only
(Only
Power
Power
On)
OFF)
Remote Control Button
Remote Control Button
Remote Control Button
Remote Control Button
Remote Control Button
Remote Control Button
Remote Control Button
53
Reference
Programming
the Remote control
control
The remote control is
to
grammed
operate
be promost remote-controllable devices of other manufacturers.
a
multi-brand
universal remote control. It
or
can
Note that the remote control may not control all models of other brands.
Programming
a
code into
1. Test your remote control.
To find out whether your remote control
gramming,
turn
mode button
on
(such
the
component such
as a
DVD
or
VCR)
2. Turn
operate the component without pro-
VCR and press the
the remote control, while
D
/ E buttons to
requires programming
see
to
corresponding
pointing at the
if the
component
operate the device.
programmed, then press the corresponding mode
button (such as a DVD or VCR) on the remote control. The remote control button
of desired device is lighted.
on
the
If not, the remote
remote mode
as a
on
component. Test the POWER and PR
responds properly.
can
a
component
to be
3. Press the MENU and MUTE buttons
be
programmed
4. Enter
a
code
simultaneously,
the remote control is
ready
to
for the code.
number
using
Programming code numbers
the following pages. Again, if
the
for the
number
buttons
on
the
corresponding component
remote
can
control.
be found
on
the code is correct, the device will turn off.
5. Press the MENU button to store the code.
6. Test the remote control functions to
repeat from step
54
2.
see
if the
component responds properly. If not,
Programming
Codes
Codes
A VCRs
Brand
Codes
Brand
Codes
AIWA
034
KENWOOD
014
034
AKAI
016
043
047
048
125
146
001
012
013
101
106
114
046
124
LG
AMPRO
072
ANAM
031
033
103
AUDIO DYNAMICS
012
023
039
BROKSONIC
035
037
129
CANON
028
031
033
CAPEHART
108
CRAIG
003
040
135
CURTIS MATHES
031
033
041
DAEWOO
005
007
010
064
065
108
110
111
112
116
117
119
043
(GOLDSTAR)
039
Brand
Codes
PORTLAND
108
TATUNG
039
043
PULSAR
072
TEAC
034
039
043
020
QUARTZ
011
014
TECHNICS
031
033
070
123
QUASAR
033
066
075
145
TEKNIKA
019
031
033
034
RCA
013
020
033
034
043
034
LXI
003
009
013
014
040
041
062
063
THOMAS
034
017
034
101
106
107
109
140
144
TMK
006
145
147
TOSHIBA
008
013
042
047
003
008
010
014
059
082
112
131
031
033
034
040
TOTEVISION
040
101
053
054
101
UNITECH
040
MAGIN
040
MAGNAVOX
031
033
067
068
012
031
MARANTZ
034
033
041
REALISTIC
067
RICO
058
VECTOR RESEARCH
012
MARTA
101
RUNCO
148
VICTOR
048
MATSUI
027
030
SALORA
014
VIDEO CONCEPTS
012
MEI
031
033
SAMSUNG
032
040
102
104
VIDEOSONIC
040
MEMOREX
003
010
014
031
105
107
109
112
WARDS
033
034
053
072
113
115
120
122
101
102
134
139
125
059
DBX
012
023
DYNATECH
034
053
ELECTROHOME
059
EMERSON
006
017
025
027
MGA
045
046
029
031
034
035
MINOLTA
013
020
036
037
046
101
MITSUBISHI
013
020
045
046
129
131
138
153
049
051
059
061
FISHER
003
008
009
010
151
FUNAI
034
GE
031
033
063
107
109
144
GO VIDEO
132
136
HARMAN KARDON
012
045
HITACHI
004
018
026
043
063
137
INSTANTREPLAY
031
033
JCL
031
033
JCPENNY
012
013
015
040
066
101
034
040
072
MULTITECH
024
034
147
NEC
012
023
039
034
OPTONICA
053
054
150
PANASONIC
066
070
074
133
140
145
013
020
031
JVC
012
031
033
043
048
050
055
060
130
150
152
013
017
024
031
033
034
040
053
054
131
043
048
135
YAMAHA
012
034
039
043
SANYO
003
007
010
014
ZENITH
034
048
056
058
102
134
072
080
101
017
037
112
129
003
008
009
010
013
014
017
020
031
042
073
081
054
149
SCOTT
043
101
043
043
003
022
SEARS
NORDMENDE
033
046
SANSUI
048
PENTAX
034
131
MTC
JENSEN
101
069
108
043
Codes
LLOYD
DAYTRON
039
Brand
083
031
034
067
PHILIPS
031
033
034
067
071
101
054
SHINTOM
024
SONY
003
009
031
052
056
057
058
076
077
078
149
033
034
SOUNDESIGN
034
STS
013
SYLVANIA
031
059
067
PILOT
101
PIONEER
013
Brand
Codes
INKEL
037
058
062
069
078
079
095
230
122
149
AKAI
163
152
ANAM
003
014
017
023
059
106
189
216
217
235
236
021
031
033
063
PHILCO
SHARP
048
SYMPHONIC
034
TANDY
010
034
A AUDIO
Brand
Codes
AIWA
014
028
070
096
125
129
139
229
Brand
Codes
MARANTZ
002
018
020
121
034
041
081
150
151
097
112
153
154
155
MEMOREX
157
158
159
160
189
207
222
224
225
226
227
243
BURMECTER
252
CARVER
086
KEC
185
186
187
CLARION
199
KENWOOD
038
050
067
089
DAEWOO
027
053
060
084
170
171
197
206
102
148
198
221
215
222
DENON
015
075
130
143
FANTASIA
Brand
Codes
025
SANYO
019
083
090
SCOTT
106
186
SHARP
031
032
051
052
107
072
082
117
119
NAD
046
156
184
199
200
ONKYO
013
040
041
047
206
209
048
056
057
132
SHERWOOD
005
006
158
133
140
SONY
044
045
109
114
118
126
248
249
012
020
073
074
076
077
105
161
162
163
164
165
166
167
168
169
205
231
233
242
010
085
106
136
185
187
237
101
113
128
134
147
218
066
092
247
OPTIMUS
158
PANASONIC
007
033
064
113
142
220
241
251
PENNEY
104
PHILIPS
026
112
143
PIONEER
039
042
043
063
KOHEL
030
071
NAD
045
046
FINEARTS
022
LOTTE
014
016
036
098
065
091
093
094
FISHER
089
099
100
172
173
174
115
123
127
250
LG
001
021
024
029
175
176
177
178
QUASAR
113
087
107
108
110
179
180
181
183
RCA
080
190
191
192
210
201
202
208
213
RCX
092
211
212
239
214
219
223
232
REALISTIC
103
106
034
035
188
238
240
SAMSUNG
124
145
146
(GOLDSTAR)
HAITAI
HARMAN/KARDON 068
JVC
004
MCS
104
013
141
222
TAEKWANG
TEAC
TECHNICS
TOSHIBA
137
THE
061
182
VICTOR
088
LXI
103
193
194
195
203
WARDS
089
MAGNAVOX
111
204
244
245
246
YAMAHA
054
MCINTOSH
049
011
135
138
144
SANSUI
234
131
055
199
55
Reference
Programming
Codes
Codes
A DVD
Brand
Codes
Brand
Codes
Brand
Codes
Brand
Codes
APEX DIGITAL
022
MAGNAVOX
013
PHILIPS
013
SONY
007
DENON
020
014
MARANTZ
024
PIONEER
004
THOMPSON
005
006
GE
005
006
MITSUBISHI
002
PROCEED
021
TOSHIBA
019
008
HARMAN KARDON 027
NAD
023
PROSCAN
005
006
YAMAHA
009
018
JVC
012
ONKYO
008
017
RCA
005
006
ZENITH
010
016
LG
001
PANASONIC
003
009
SAMSUNG
011
015
Brand
Codes
Brand
Codes
Brand
Codes
PHILIPS
006
012
013
SPRUCER
047
078
065
085
090
STARCOM
002
004
034
051
052
STARGATE
008
030
076
TADIRAN
030
TAEKWANG
110
TAIHAN
105
TANDY
017
(GOLDSTAR)
010
016
025
026
025
A CABLE
Brand
Codes
ABC
003
004
039
046
052
053
042
GOLDEN CHANNEL 030
HAMLIN
049
050
055
AJIN
112
HITACHI
052
055
ANTRONIK
014
HOSPITALITY
070
077
ARCHER
005
JERROLD
002
003
004
008
PRUCER
059
CABLE STAR
026
009
010
052
069
PTS
011
048
CENTURION
092
074
073
074
CENTURY
007
LG
CITIZEN
007
M-NET
COLOUR VOICE
065
090
COMBANO
080
COMTRONICS
019
DIAMOND
023
EAGLE
020
030
040
EASTERN
057
062
066
ELECTRICORD
032
OAK
016
031
GE
072
PANASONIC
044
047
GEMINI
008
022
PARAGON
100
GI
052
074
007
014
024
PIONEER
071
020
063
072
PULSAR
100
TEXSCAN
029
037
RCA
047
TOCOM
039
MACOM
033
REGAL
049
TOSHIBA
100
081
MAGNAVOX
010
REGENCY
057
UNIKA
030
MEMOREX
100
REMBRANT
025
MOVIE TIME
028
032
SAMSUNG
102
107
030
068
NSC
015
028
SCIENTIFIC ATLANTA
003
011
041
042
043
045
046
025
(GOLDSTAR)
001
106
012
101
064
038
005
079
071
073
054
SHERITECH
022
SIGNAL
030
SIGNATURE
052
POST NEWS WEEK 016
SL MARX
030
037
053
050
008
009
040
056
007
014
024
UNITED CABLE
004
053
UNIVERSAL
005
007
014
024
026
027
032
035
012
015
018
086
087
088
089
ZENITH
100
114
060
093
Brand
Codes
035
047
0 57
VIEWSTAR
A STB
Brand
Codes
Brand
Codes
Brand
Codes
ALPHASTAR DSR
123
EUROPLUS
114
MACOM
010
AMPLICA
050
FUJITSU
017
021
BIRDVIEW
051
126
129
133
134
CHANNEL MASTER 013
014
015
003
004
016
036
055
031
059
101
CHAPARRAL
008
009
HITACHI
139
140
CITOH
054
HOUSTON TRACKER
033
037
CURTIS MATHES
050
145
057
104
DRAKE
005
006
007
010
HUGHES
068
011
052
112
116
JANIEL
060
JERROLD
012
0 18
077
141
GENERAL INSTRUMENT
022
039
027
0 29
0 51
059
063
064
SATELLITE SERVICE CO 028
065
085
NEXTWAVE
028
124
SONY
103
NORSAT
069
070
STARCAST
041
PACE SKY SATELLITE
143
SUPER GUIDE
020
124
125
PANASONIC
060
TEECOM
023
026
075
087
PANSAT
121
088
090
107
130
PERSONAL CABLE 117
137
125
142
PHILIPS
071
TOSHIBA
002
127
PICO
105
UNIDEN
016
025
042
043
061
PRESIDENT
019
102
044
045
048
049
110
078
079
080
086
101
135
136
147
DX ANTENNA
024
046
056
076
KATHREIN
108
PRIMESTAR
030
ECHOSTAR
038
040
057
058
LEGEND
057
PROSAT
072
093
094
095
096
LG
001
RCA
066
106
VIEWSTAR
115
097
098
099
100
LUTRON
132
REALISTIC
043
074
WINEGARD
128
146
122
LUXOR
062
SAMSUNG
123
ZENITH
081
082
089
MEMOREX
057
SCIENTIFIC ATLANTA
032
091
120
ELECTRO HOME
56
(GOLDSTAR)
144
138
111
083
084
Reference
Checklist
T
Checklist
roubleshooting
Troubleshooting
The
doesn't work
Power is
suddenly
turned off
normally.
?
if there is any
control causing obstruction.
?
Are batteries installed with correct
?
Correct remote
?
Install
new
?
Is the
sleep
?
Check the power control settings. Power interrupted
No broadcast on station tuned with Auto off activated.
The remote control
?
Check to
does not work
operation
see
operating
object
between the
polarity (+
mode set:
product
to +,
-
to
and the remote
-)?
TV, VCR etc.?
batteries.
timer set?
The video function does not work.
No
picture
&
No sound
Check whether the
?
Try
?
Is the power cord inserted into wall power outlet?
Check your antenna direction and/or location.
?
Picture appears
slowly after
switching
?
Test the wall power outlet, plug another product's power cord into the outlet
where the product's power cord was plugged in.
?
This is
on
or
poor color
poor
picture
normal, the image is muted during the product startup process.
Please contact your service center, if the
minutes.
?
or
with the broadcast.
?
?
No
another
product is turned on.
channel. The problem may be
?
?
?
has not
picture
appeared
after five
Adjust Color in menu option.
Keep a sufficient distance between the product and the VCR.
Try another channel. The problem may be with the broadcast.
Are the video cables installed properly?
Activate any function to restore the brightness of the picture.
Horizontal/vertical bars
ture
Poor
Lines
on
channels
or
Check for local interference such
?
Station
or
?
Station
signal
?
Check for
?
Check antenna
or
reception
some
in
picshaking
?
streaks
pictures
cable
is
as an
electrical
product experiencing problems,
weak, reorient
sources
of
possible
(Change
appliance
or
power tool.
tune to another station.
antenna to receive weaker station.
interference.
the direction of the
antenna).
57
The audio function does not work.
?
Press the VOL
Picture OK &
?
Sound muted? Press MUTE button.
No sound
?
Try
problem may be with the broadcast.
Are the audio cables installed properly?
Check whether the TV Speaker is On in the SOUND menu.
?
?
No
output
of the
from
one
VOLUME button.
or
another channel. The
Adjust
?
Balance in
menu
speakers
Unusual sound
A
?
from inside the
change
in ambient
noise when the
product
the
humidity or temperature may result in an unusual
product is turned on or off and does not indicate a fault with
product.
There is
a
(Only
The
option.
signal
range.
Vertical bar
PC mode
horizontal
?
Adjust resolution,
?
Check it whether the
?
Check the
?
Work the Auto
?
Check the
?
Reinstall the PC video card.
is out of
input
frequency,
Screen color is
color
58
vertical
or
frequency.
loose.
source.
configure
or
adjust clock, phase,
position
or
or
cable is connected
signal
Horizontal Noise &
unstable
applied)
or
stripe on background &
Incorrect
in PC mode.
problem
single
signal
cable.
or
H/V
position.
Product
Specifications
Power
Requirement
AC 100-240V
Power
Consumption
180W
Television
System
Programme Coverage
PAL/SECAM
VHF: NZ1
B/G/D/K, PAL I/II, NTSC-M
E12, UHF: E21
~
HYPER: S21
External Antenna
?
The
Impedance
specifications
50/60Hz 2.0A
~
~
~
E69, CATV: S1
S20,
~
S47
75Ω
shown above may be
changed
without
prior
notice for
quality improvement.
59
Download PDF