LG | RT-42LZ30 | LG RT-42LZ30 Owner’s Manual

LCD
Colour Television
OWNER’S MANUAL
Please read this manual carefully before operating your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote this
information to your dealer when you require service.
Model number
Serial number
:
:
P/NO : 3828TUL300B (0510-REV02)
Printed in Korea
Contents
Installation
3
Location and function of controls
4
Remote control
Internal generator charge / Front/Side panel / Back panel
Basic operation
8
On and off / Programme selection
Volume adjustment
Quick view / Mute function
On screen language selection
ON SCREEN Menus
9
Menu selection
STATION Menu
10
Auto programme tuning
Manual programme tuning
Assigning a station name/Fine tuning
Programme edit
Favourite programme/Calling the programme table
PICTURE Menu
15
PSM (Picture Status Memory)
Picture adjustment
ACC/ XD
SOUND Menu
17
SSM (Sound Status Memory)
Sound adjustment/SRS WOW
Stereo/Dual reception / NICAM reception
Sound output selection
TIMER menu
20
Clock / On/Off Time / Auto Off / Sleep timer
SPECIAL Menu
22
Main Picture Source Selection
Child lock/Power Indicator/Transparency
Picture Size Zoom/Reset
SCREEN Menu
25
Picture format
Auto adjustment /Clock and Phase
SCREEN Position
Manual Configure
Screen adjustments
Initializing (Reset to original factory value)
Selecting Wide XGA mode
YNR (Y-signal Noise Reduction) / Split Zoom
PIP/POP/PBP operation
28
PIP/POP/PBP mode / Input mode selection for sub picture
Sub Picture / Size Source
Image / Sound /Moving the sub Picture
Swap / Swapping between main and sub pictures
Programme selection for sub picture
Teletext (This feature is not available in all countries.)
32
Switch on/off / SIMPLE text / TOP text (This feature is not available in all countries.)
FASTEXT / Special teletext functions
Connection of external equipment
35
Aerial socket / Euro scart sockets
S-Video/Audio in sockets (S-Video)
PC in socket / Audio/Video in sockets
Displayable Monitor Specification
37
RGB Mode / DVI Mode
External Control Device Setup
38
RS-232C input socket / D-Sub 9-pin male
Set ID / Communication Parameters
Command Reference List
Transmission/Receiving Protocol
Programming the Remote control
42
Programming Codes
43
Troubleshooting check list
47
2
Installation
Power
This set operates on an AC mains supply, the voltage is as indicated on the label on the back cover. Never apply DC power to the set.
In the event of thunderstorms or powercuts, please pull out the aerial and mains plugs.
a. Open the back panel cover.
b. After connecting the power cord to the set, connect the power
cord to an AC mains.
c. Fix cables with the supplied cable tie after collecting connected
cables.
d. Pull the cables through the hole on the set.
e. Close the back panel cover.
a/e
Warning
To prevent fire or shock hazard, do not expose the set to rain or moisture. Do not rub or strike the Active Matrix LCD with anything hard as
this may scratch, mar, or damage the Active Matrix LCD permanently.
Service
Never remove the back cover of the set as this can expose you to
high voltage and other hazards. If the set does not operate properly, unplug it and call your dealer.
b
Aerial
Connect the aerial cable to the socket marked +75 Ω on the back.
For the best reception an outdoor aerial should be used.
Location
Position your set so that no bright light or sunlight falls directly onto
the screen. Care should be taken not to expose the set to any
unnecessary vibration, moisture, dust or heat. Also ensure that the
set is placed in a position to allow a free flow of air. Do not cover
the ventilation openings on the back cover.
If you intend to mount the TV to a wall, attach VESA standard mounting interface (optional parts) to the back of the TV. When you install
d
the set to use the wall mounting bracket (optional parts), fix it carefully so as not to drop.
Cleaning
Unplug the set before cleaning the face of the LCD Screen. Dust
the set by wiping the screen and the cabinet with a soft, clean cloth.
If the screen requires additional cleaning, use a clean, damp cloth.
Do not use liquid cleaners or aerosol cleaners.
On Disposal
The fluorescent lamp used in this product contains a small amount
of mercury.
Do not dispose of this product with general household waste.
Disposal of this product mute be carried out in accordance to the
regulations of your local authority.
3
Location and function of controls
All the functions can be controlled with the remote control.
Some functions can also be adjusted with the buttons on the side
panel of the set.
Remote Control
1. POWER
Switches the set on from standby or off to standby.
2. TV/AV
Selects TV, AV, S-Video, Component1, Component2,
RGB PC, DVI PC modes.
switches the set on from standby.
1
2
3
4
TV/AV
MODE
INPUT
ARC
POWER
3. INPUT
Selects TV, AV, S-Video, Component1, Component2,
RGB PC, DVI PC modes.
MUTE
4. ARC (Aspect Ratio Control)
Changes the picture format.
5
LIST
5. NUMBER BUTTONS
Switches the set on from standby or directly select a number.
Q.VIEW
6
PSM
7
8
6. LIST
Displays the programme table.
SSM
VOL
PR
7. PSM (Picture Status Memory)
Recalls your preferred picture setting.
TEXT
PIP/POP/PBP
MENU
EXIT
8. VOLUME UP/DOWN
Adjusts the volume.
Programme UP/DOWN
Selects a programme.
9
10
OK
9. MENU
Selects a menu.
PIP PR-
10.
PIP INPUT
PIP PR+ SWAP
PLAY
11
REW
PAUSE
STOP RECORD
FF
SKIP
D / E /F / G (Up/Down/Left/Right) BUTTONS
Selects a menu item.
Adjusts menu settings.
OK
Accepts your selection or displays the current mode.
11. VCR/DVD BUTTONS
12
WIN.SIZE WIN.POSITION
SLEEP
I/II
REVEAL
SIZE
UPDATE
HOLD
TIME
INDEX
MODE
i
M
Control some video cassette recorders or DVD player
("RECORD" button is not available for DVD player).
?
MIX
13
12. SLEEP
Sets the sleep timer.
13. TELETEXT BUTTONS (This feature is not available in all countries.)
These buttons are used for teletext.
For further details, see the ‘Teletext’ section.
: No function
*
(With TELETEXT)
4
Location and function of controls
14. MODE
Selects the remote operating mode: TV, VCR, DVD, CABLE,
STB or AUDIO. Select other operating modes, for the remote to
operate external devices.
15. MUTE
Switches the sound on or off.
16. Q.VIEW
Returns to the previously viewed programme.
Selects a favorite programme.
17. SSM (Sound Status Memory)
Recalls your preferred sound setting.
18. PIP BUTTONS
PIP/POP/PBP
Switches the sub picture select PIP, POP, PBP or off modes.
PIP PR +/Selects a programme for the sub picture.
SWAP
Alternates between main and sub picture.
PIP INPUT
Selects the input mode for the sub picture.
WIN.SIZE
Adjusts the sub picture size.
WIN POSITION
Moves the sub picture to D / E or F / G direction.
19. EXIT
Exits from each mode.
14
TV/AV
MODE
INPUT
ARC
MUTE
LIST
15
Q.VIEW
16
PSM
SSM
VOL
17
PR
PIP/POP/PBP
*
MENU
EXIT
20. I/II
Selects the language during dual language broadcast.
Selects the sound output.
Note: In teletext mode, the PIP PR -/+, SWAP and PIP INPUT buttons are used for teletext function.
POWER
18
13
19
OK
PIP PR-
PIP INPUT
18
PIP PR+ SWAP
PLAY
REW
PAUSE
STOP RECORD
FF
SKIP
WIN.SIZE WIN.POSITION
SLEEP
I/II
20
Installing Batteries
• Open the battery compartment cover on the back side and insert
two 1.5V AA size batteries in correct polarity (+ with +, - with -).
• Don’t mix old or used batteries with new ones.
• Close the cover.
(Without TELETEXT)
5
Location and function of controls
Front / Side panel
PR
6
VOL
5
OK
4
MENU
3
TV
2
l
AV
/l
ON/OFF
1
8
7
l
1.
/ l (ON / OFF)
Switches the set on or off.
2. TV / AV
Selects TV, AV, S-Video, Component1,
Component2, RGB PC, DVI PC modes
switches the set on from standby.
3. MENU
Selects a menu.
6.
D / E (Programme Up/Down)
Selects a programme or a menu item.
Switches the set on from standby.
7. POWER/STANDBY Indicator
Illuminates red in standby mode.
Illuminates green when the set is switched on.
Illuminates amber in RGB PC/DVI PC mode
(DPM Mode).
8. Remote Control Sensor
4. OK
Accepts your selection or displays the current
mode.
5.
6
F / G (Volume Down/Up)
Adjusts the volume.
Adjusts menu settings.
Location and function of controls
R
AUDIO L / MOLO
VIDEO
S-VIDEO
AUDIO L / MOLO
VIDEO
S-VIDEO
Back panel
8
R
AV3
AV
COMPONENT1
RS-232C
OUT
AC IN
DVI PC
REMOTE
CONTROL
RGB PC
1
2
COMPONENT2
(480i/576i)
PC AUDIO IN
3
VIDEO IN
4
ANT IN
AV
OUT
L
RS-232C
IN
R
VIDEO
L AUDIO R
AUDIO IN
5
6
7
1. POWER CORD SOCKET
6. AV OUT SOCKETS
2. REMOTE CONTROL JACK
7. AERIAL SOCKET
Connect the RF socket of the VCR to the aerial socket.
3. RS-232C SERIAL PORTS
4. DVI (Digital Visual Interface) PC / RGB PC /
PC AUDIO IN SOCKETS
Connect the set output socket of the PERSONAL COMPUTER to this socket.
5. COMPONENT1(DTV, DVD), COMPONENT2
(DVD) IN SOCKETS
Connect the audio/video out sockets of external
equipment to these sockets.
8. AUDIO/VIDEO IN SOCKETS (AV)
Connect the audio/video out sockets of external equipment to these sockets.
S-VIDEO/AUDIO IN SOCKETS (SAV)
Connect the video out socket of an S-VIDEO
VCR to the S-VIDEO socket.
Connects the audio out sockets of the SVIDEO VCR to the audio sockets as in AV.
7
Basic Operation
On and off
1. Press the main power button to switch the set on.
2. If the set is in standby mode, press the POWER, TV/AV, PR +/, INPUT, or NUMBER buttons on the remote control to switch it
on fully.
3. Press the POWER button on the remote control.
The set reverts to standby mode.
4. Press the main power button again to switch the set off.
Note : If, while the set is switched on, the mains plug is disconnected the set will switch to standby or power on when the mains
plug is replaced in the mains power socket.
POWER
MUTE
INPUT
Programme selection
You can select a programme number with the PR +/- or NUMBER
buttons.
Q.VIEW
SSM
Volume adjustment
Press the VOL +/- button to adjust the volume.
Quick view
Press the Q.VIEW button to view the last programme you were
watching.
MENU
Note : This function works only when Favourite programme is
set to Off . Otherwise each press of this button will select a stored
favourite programme.
OK
PIP INPUT
Mute function
SWAP
Press the MUTE button. The sound is switched off and the display
appears.
You can cancel it by pressing the MUTE, VOL +/-, I/II or SSM button.
I/II
On screen language selection
The menu can be displayed on the screen in your desired language. First select your language.
1. Press the MENU button and then D / E button to select the
SPECIAL menu.
2. Press the G button and then D / E button to select
Language.
3. Press the G button and then the D / E button to select your
desired language.
All the on screen displays will appear in the selected language.
4. Press the MENU button to save.
8
On Screen Menus
The dialogue between you and your set takes place on screen with
an operator menu.
Menu selection
1. Press the MENU button and then D / E button to display each
menu.
2. Press the G button and then the D / E button to select a menu
item.
3. Repeatedly press the MENU button to return to normal TV
viewing.
Note : In the teletext mode, menus are not displayed.
PICTURE
STATION
Auto programme
PSM
Manual programme
ACC
Programme edit
XD
Favourite programme
Prev.
MENU
Prev.
MENU
STATION menu
PICTURE menu
MENU
PIP/POP/PBP
SOUND
On/Off
SSM
Balance
AVL
SRS WOW
Source
Size
Image
OK
Sound
Position
Swap
MENU
Prev.
PIP/POP/PBP menu
SOUND menu
SCREEN
ARC
Auto-configure
Clock
Phase
Position
Prev.
MENU
TIMER
SPECIAL
Input
Clock
Child lock
Off time
Language
On time
Power indicator
Auto off
Transparency
Zoom
Reset
E
MENU
Prev.
SCREEN menu
MENU
Prev.
SPECIAL menu
MENU
Prev.
TIMER menu
9
STATION Menu
STATION
Auto programme
Manual programme
Programme edit
Favourite programme
Up to 100 (only china : 200) TV stations can be stored in this set by
programme numbers (0 to 99(only china :0 to 199)). Once you have
preset the stations, you will be able to use the D / E or NUMBER
buttons to scan the stations you programmed.
Stations can be tuned using automatic or manual modes.
Auto programme tuning
MENU
Prev.
STATION menu
All stations that can be received are stored by this method. It is recommended that you use auto programme during installation of this set.
1. Press the MENU button and then D / E button to select the
STATION menu.
2. Press the G button and then D / E button to select Auto
Programme.
3. Press the G button. Select a TV system with the G button and
then D / E button on the System menu;
System
BG
I
DK
M
G
Storage from
Start
MENU
Prev.
(Asia/New Zealand/M.East/Africa/Australia)
(Hong Kong/South Africa)
(East Europe/China/Africa/CIS)
(USA/Korea/Philippines) (This feature is not available in
all countries.)
4. Press the OK button.
5. Press the D / E button to select Storage from. And press the
G button. Select the beginning programme number with the D /
E button or NUMBER buttons on the Storage from menu.
6. Press the OK button.
BG
I
DK
M
:
:
:
:
MENU
11
OK
CO5
17%
7. Press the D / E button to select Start.
8. Press the G button to begin auto programming.
All receivable stations are stored. The station name is stored for
stations which broadcast VPS (Video Programme Service),
PDC (Programme Delivery Control) or TELETEXT data. If no
station name can be assigned to a station, the channel number
is assigned and stored by a number as shown below.
AUSTRALIA
BG
I
DK
M
V/UHF
1 ~ 75
1 ~ 69
1 ~ 69
2 ~ 83
Cable
2 ~ 44
1 ~ 47
1 ~ 47
1 ~ 71
CHINA
V/UHF
1 ~ 69
1 ~ 69
1 ~ 62
2 ~ 83
Cable
1 ~ 47
1 ~ 47
1 ~ 41
1 ~ 71
ELSE
V/UHF
1 ~ 69
1 ~ 69
1 ~ 69
2 ~ 83
Cable
1 ~ 47
1 ~ 47
1 ~ 47
1 ~ 71
To stop auto programming, press the MENU button.
When auto programming is completed, the Programme edit
menu appears on the screen. See the ‘Programme edit’ section
to edit the stored programme.
9. Repeatedly press the MENU button to return to normal TV
viewing.
10
STATION Menu
Manual programme tuning
STATION
Auto programme
Manual programme lets you manually tune and arrange the stations in whatever order you desire. Also you can assign a station
name with five characters to each programme number.
1. Press the MENU button and then D / E button to select the
STATION menu.
2. Press the G button and then D / E button to select Manual
Programme.
3. Press the G button and then D / E button to select System.
System
G
Storage
Channel
Name
Manual programme
Programme edit
Favourite programme
MENU
Prev.
STATION menu
BG
I
DK
M
Fine tune
Search
MENU
Prev.
4. Select a TV system with the G button and then D / E button on
the System menu;
BG : (Asia/New Zealand/M.East/Africa/Australia)
I
: (Hong Kong/South Africa)
DK : (East Europe/China/Africa/CIS)
M : (USA/Korea/Philippines) (This feature is not available in
all countries.)
5. Press the OK button.
6. Press the D / E button to select Storage. And press the G button. Select the beginning programme number with the D / E
button or NUMBER buttons on the Storage menu.
System
System
Storage
G
1
MENU
Storage
Channel
Channel
Name
Name
Fine tune
Fine tune
Search
Search
G
V/UHF
1
OK
MENU
Prev.
MENU
Prev.
7. Press the OK button.
8. Press the D / E button to select Channel.
9. Press the G button and then D / E button to select VHF/UHF
or Cable on the Channel menu. Then press the G button.
You can select the desired channel number with the NUMBER
buttons. If possible, select the channel number directly with the
number buttons. Refer to page 10.
10. Press the OK button.
11. Press the D / E button to select Search.
12. Press the G button.
13. Press the OK button to store it.
14. To store another station, repeat steps 3 to 12.
15. Repeatedly press the MENU button to return to normal TV
viewing.
11
STATION Menu
STATION
Assigning a station name
Auto programme
Manual programme
Programme edit
Favourite programme
1. Repeat the ‘Manual programme tuning’ steps 1 to 2.
2. Press the G button and then D / E button to select Name.
System
MENU
Storage
Prev.
Channel
Name
STATION menu
G
C
0
1
Fine tune
Search
MENU
Prev.
3. Press the G button and then use the D / E. You can use a blank,
+, -, the number 0 to 9 and the alphabet A to Z.
With the F button you can select in the opposite direction.
4. Select the position by pressing the F / G button and then make
your choice of the second character, and so on.
5. Press the OK button to store it.
6. Repeatedly press the MENU button to return to normal TV
viewing.
Fine tuning
Normally fine tuning is only necessary if reception is poor.
1. Repeat the ‘Manual programme tuning’ steps 1 to 2.
2. Press the G button and then D / E button to select Fine tune.
System
Storage
MENU
Channel
Name
Fine tune
G
GGG
Search
OK
MENU
Prev.
3. Press the G button to fine tune for the best picture and sound.
4. Press the OK button.
5. Repeatedly press the MENU button to return to normal TV
viewing.
The finely tuned programme will be indicated by yellow number
during programme selection.
12
STATION Menu
Programme edit
STATION
Auto programme
This function enables you to delete or skip the stored programmes.
Also you can move some stations to other programme numbers or
copy a blank station data into the selected programme number.
1. Press the MENU button and then use D / E button to select the
STATION menu.
2. Press the G button and then D / E button to select
Programme edit.
3. Press the G button to display the Programme edit menu.
0 C 05
1 C 05
2 C 05
3 C 05
4-----
5-----
6-----
7-----
9-----
10 C 05
11 C 05
12 C 05
13 C 05
14 C 05
15 - - - - -
16 - - - - -
16 - - - - -
17 - - - - -
18 - - - - -
19 - - - - -
MENU
Prev.
Delete
Move
Copy
Skip
Manual programme
Programme edit
Favourite programme
MENU
Prev.
STATION menu
Deleting a programme
1. Select a programme to be deleted with the D / E or F / G button.
2. Press the RED button twice.
The selected programme is deleted, all the following programmes are shifted up one position.
Copying a programme
1. Select a programme to be copied with the D / E or F / G button.
2. Press the GREEN button.
All the following programmes are shifted down one position.
Moving a programme
1. Select a programme to be moved with the D / E or F / G button.
2. Press the YELLOW button.
3. Move the programme to the desired programme number with
the D / E or F / G button.
4. Press the YELLOW button again to release this function.
Skipping a programme number
1. Select a programme number to be skipped with the D / E or F
/ G button.
2. Press the BLUE button. The skipped programme turns to blue.
3. Press the BLUE button again to release the skipped programme.
When a programme number is skipped it means that you will be
unable to select it using the D / E button during normal TV
viewing. If you want to select the skipped programme, directly
enter the programme number with the NUMBER buttons or
select it in the programme edit or table menu.
MENU
PIP PR-
PIP INPUT
PIP PR+ SWAP
Repeatedly press the MENU button to return to normal TV viewing.
13
STATION Menu
Favourite programme
STATION
Auto programme
Manual programme
Programme edit
Favourite programme
This function lets you select your favourite programmes directly.
1. Press the MENU button and then D / E button to select the
STATION menu.
2. Press the
G
button and then
D
/
E
to select Favourite pro-
gramme.
MENU
Prev.
---------
STATION menu
3.
4.
5.
6.
ON
---------------------------------
Press the G button and then F / G button to select On or Off.
Press the D / E button to select - - - - - - - .
Select a desired programme with the F / G button.
To store another programme, repeat steps 4 to 5.
You can store up to 8 programmes.
7. Press the MENU button to return to normal TV viewing.
Repeatedly press the Q.VIEW button to select stored favourite programmes.
Calling the programme table
LIST
Q.VIEW
You can check the programmes stored in the memory by displaying
the programme table.
Displaying programme table
Press the LIST button to display the Programme table menu.
The programme table appears on the screen.
PROGRAMME LIST
MENU
OK
0 C 05
1 C 05
2 C 05
3 C 05
4-----
5-----
6-----
7-----
9-----
10 C 05
11 C 05
12 C 05
13 C 05
14 C 05
15 - - - - -
16 - - - - -
16 - - - - -
17 - - - - -
18 - - - - -
19 - - - - -
Note :
a. You may find some blue highlighted programmes shown. They
have been set up in the programme edit mode.
b. Some programmes with the channel number shown in the programme table indicate there is no station name assigned.
Selecting a programme in the programme table
Select a programme with the D / E or F / G button.
Then press the OK button.
The set switches to the chosen programme number.
Paging through a programme table
There are 10 programme table pages in which contain 199 programmes.
Pressing the D / E or F / G button repeatedly turns the pages.
Repeatedly press the MENU button to return to normal TV viewing.
14
PICTURE Menu
PSM (Picture Status Memory)
PICTURE
PSM
1. Press the MENU button and then D / E button to select the PICTURE menu.
2. Press the G button and then D / E button to select PSM.
ACC
XD
PICTURE
PSM
G
ACC
XD
Dynamic
Standard
Mild
Game
User
MENU
Prev.
PICTURE menu
Prev.
MENU
3. Press the G button and then D / E button to select a picture setting on the PSM menu.
4. Press the MENU button to save.
You can also recall a desired picture (Dynamic, Standard,
Mild, Game or User) with PSM button on the remote control. The
picture Dynamic, Standard, Mild and Game are programmed
for optimum picture reproduction at the factory and cannot be
changed.
Picture adjustment
You can adjust picture contrast, brightness, colour intensity, sharpness and tint (NTSC only) to the levels you prefer.
PSM
1. Press the MENU button and then D / E button to select the
PICTURE menu.
2. Press the G button and then D / E button to select PSM.
MENU
PICTURE
PSM
G
ACC
XD
Contrast
Brightness
Dynamic
Standard
Mild
Game
User
Color
Sharpness
Tint
MENU
Prev.
Contrast 100
F
G
3. Press the G button and then D / E button to select User.
4. Press the F button and then D / E button to select the desired
picture option. (Contrast, Brightness, Color, Sharpness
and Tint)
5. Press the F / G button to make appropriate adjustments.
6. Press the MENU button to save.
15
PICTURE Menu
PICTURE
ACC
PSM
To initialize values (reset to default settings), select the Normal
option.
ACC
XD
MENU
Prev.
1. Press the MENU button and then D / E button to select the
PICTURE menu.
2. Press the G button and then D / E button to select ACC.
PICTURE menu
PICTURE
PSM
ACC
G
XD
MENU
Warm
Normal
Cool
Prev.
3. Press the G button and then D
Normal or Cool.
4. Press the MENU button to save.
/ E
button to select Warm,
XD
XD is LG Electronic’s unique picture improving technology to display a real HD source though an advanced digital signal processing algorithm.
XD Demo - Use to see the difference between XD Demo On and
XD Demo Off.
MENU
1. Press the MENU button and then D / E button to select the
PICTURE menu.
2. Press the G button and then D / E button to select XD.
3. Press the G button and then D / E button to select Off, On or
XD Demo.
PICTURE
PSM
ACC
XD
MENU
G
Off
On
XD Demo
Prev.
4. Press the MENU button to save Off or On.
Press the EXIT button to stop XD Demo.
16
SOUND Menu
SSM (Sound Status Memory)
SOUND
You can select your preferred sound setting; Flat, Music, Movie or
Speech and you can also adjust the sound frequency of equalizer.
1. Press the MENU button and then
SOUND menu.
D / E
button to select the
SOUND
SSM
Balance
AVL
SRS WOW
MENU
G
SSM
Balance
AVL
SRS WOW
Flat
Music
Movie
Speech
User
MENU
Prev.
SOUND menu
Prev.
2. Press the G button and then D / E button to select SSM.
3. Press the G button and then D / E button to select a sound setting on the SSM menu.
Sound Frequency Adjustment
a. Press the OK button in User.
Equalizer
0.1
0.5
1.0
5 .0
10.0
Khz
MENU
SSM
Prev.
b. Select a sound band by pressing the F / G button.
c. Make appropriate sound level with the D / E button.
d. Press the OK button to store it for the sound User.
4. Press the MENU button to save.
You can also recall a desired sound setting (Flat, Music, Movie,
Speech or User) with SSM button on the remote control. The
sound settings Flat, Speech, Movie and Music are programmed
for optimum sound reproduction at the factory and cannot be
changed.
MENU
OK
Note : If you press the SSM button after making appropriate adjustment on the User sub menu, the display User automatically
appears even though you have already set a factory preset setting;
Flat, Music, Movie or Speech.
17
SOUND Menu
SOUND
MENU
Sound adjustment
You can adjust balance, AVL (Auto Volume Leveler). AVL automatically keeps on an equal volume level even if you change programmes.
1. Press the MENU button and then D / E button to select the
SOUND menu.
SSM
Balance
AVL
SRS WOW
SOUND
Prev.
SSM
Balance
AVL
SRS WOW
SOUND menu
MENU
Off
On
G
Prev.
2. Press the G button and then D / E button to select the desired
sound item; Balance or AVL.
3. Balance: Make desired adjustment with the F / G and then
press the OK button.
AVL: Press the D / E button to select Off or On.
4. Press the MENU button to save.
SRS WOW
The SRS WOW function plays back the mono or stereo sound input
with the dynamic surround effects. It will provide rich and profound
sound tone. If you set the SRS WOW on, user audio setting can not
be adjusted.
1. Press the MENU button and then D / E button to select the
SOUND menu.
2. Press the G button and then D / E button to select SRS WOW.
MENU
SOUND
OK
SSM
Balance
AVL
SRS WOW
MENU
Off
On
G
Prev.
3. Press the G button and then D / E button to select Off or On.
4. Press the MENU button to save
is a trademark of SRS Labs, Inc.
technology is incorporated under license from SRS Labs, Inc.
18
SOUND Menu
Stereo/Dual reception
When a programme is selected, the sound information for the station appears after the programme number and station name disappear.
Broadcast
On Screen Display
Mono
MONO
Stereo
STEREO
Dual
DUAL I
SOUND
SSM
Balance
AVL
SRS WOW
MENU
Prev.
SOUND menu
Mono sound selection
In stereo reception if the stereo signal is weak, you can switch to
mono by pressing the I/II button twice. In mono reception the depth
of sound is improved. To switch back to stereo, press the I/II button
twice again.
Language selection for dual language broadcast
If a programme received in two languages (dual language), you can
switch to DUAL I, DUAL II or DUAL I+II by pressing the I/II button repeatedly.
DUAL I sends the primary broadcast language to the loudspeakers.
DUAL II sends the secondary broadcast language to the loudspeakers.
DUAL I+II sends a separate language to each loudspeaker.
NICAM reception
If your set is equipped with the receiver for NICAM reception, the
high quality NICAM (Near Instantaneous Companding Audio
Multiplex) digital sound can be received.
Sound output can be selected according to the type of received
broadcast as follows by pressing the I/II button repeatedly.
1. When NICAM mono is received, you can select NICAM
MONO or FM MONO.
2. When NICAM stereo is received, you can select NICAM
STEREO or FM MONO. If the stereo signal is weak, switch to
FM mono.
3. When NICAM dual is received, you can select NICAM DUAL
I, NICAM DUAL II or NICAM DUAL I+II or MONO.
Sound output selection
In Component1, Component2 mode, you can select output sound for
the left and right loudspeakers.
I/II
Repeatedly press the I/II button to select the sound output.
L+R : Audio signal from audio L input is sent to the left loud
speaker and audio signal from audio R input is sent to the
right loud speaker.
L+L : Audio signal from audio L input is sent to left and right loudspeakers.
R+R : Audio signal from audio R input is sent to left and right loudspeakers.
19
TIMER Menu
TIMER
Clock
Clock
You must set the time correctly before using on/off time function.
Off time
On time
1. Press the MENU button and then D / E button to select the
TIMER menu.
2. Press the G button and then D / E button to select Clock.
Auto off
TIMER
MENU
Prev.
Clock
G
Off time
TIMER menu
Time
On time
1
:
:
56
AM
Auto off
Prev.
MENU
3.
4.
5.
6.
Press the G button and then D / E button to adjust the hour.
Press the G button and then D / E button to adjust the minute.
Press the G button and then D / E button to select AM or PM.
Press the MENU button to save.
On/Off time
The off timer automatically switches the set to standby at the preset time.
1. Press the MENU button and then D / E button to select the
TIME menu.
2. Press the G button and then D / E button to select Off time or
On time.
TIMER
Clock
Off time
Time
On time
G
Auto off
__ __
:
__ __
AM
Pr.
__ __
Volume
__ __
Off
MENU
MENU
OK
Prev.
3. Press the G button and then D / E button to adjust the hour.
4. Press the G button and then D / E button to adjust the minute.
5. Press the G button and then D / E button to adjust the morning(AM)or afternoon(PM).
6. Press the G button and then D / E button to select On or Off.
To cancel Off/On time function, press the D / E button to
select Off.
7. Only On Time function: Press the G button and then D / E
button to select the programme at turn-on and then press the G
button and then D / E button to adjust volume level.
8. Press the MENU button to save.
Note :
a. In the event of power interruption (disconnection or power failure), the clock must be reset.
b. Two hours after the set is switched on by the on time function it
will automatically switch back to standby mode unless a button
has been pressed.
c. Once the on or off time is set, these functions operate daily at
the preset time.
d. Off Time function overrides On Time function if they are set to
the same time.
e. The set must be in standby mode for the On Time to work.
20
TIMER Menu
Auto off
TIMER
Clock
Off time
If you select On on the Auto off menu, the set will automatically
switch itself to standby mode approximately ten minutes after a TV
station stops broadcasting.
On time
Auto off
1. Press the MENU button and then D / E button to select the
TIMER menu.
2. Press the G button and then D / E button to select Auto off.
3. Press the G button and then D / E button to select Off or On.
MENU
Prev.
TIMER menu
TIMER
Off
Clock
On
Off time
On time
Auto off
MENU
G
Prev.
4. Press the MENU button to save.
Sleep timer
You don’t have to remember to switch the set off before you go to
sleep. The sleep timer automatically switches the set to standby
after the preset time has elapsed.
Press the SLEEP button to select the number of minutes. The display ‘
0 MIN’ will appear on the screen, followed by 10, 20, 30,
60, 90, 120, 180 and 240. The timer begins to count down from the
number of minutes selected.
Note :
a. To view the remaining sleep time, press the SLEEP button
once.
b. To cancel the sleep time, repeatedly press the SLEEP button
until the display ‘
0 MIN’ appears.
c. When you switch the set off, the set releases the preset sleep
time.
MENU
OK
SLEEP
21
SPECIAL Menu
SPECIAL
Main Picture Source Selection
Input
Child lock
Language
Power indicator
Transparency
Zoom
Inputs can be set for TV, AV, S-Video, Component1, Component2,
RGB PC, DVI PC mode. AV mode is used when a video cassette
recorder (VCR), or other equipment is connected to the set.
Reset
E
MENU
Prev.
SPECIAL menu
Note : When a VCR is connected via the aerial socket the set is
used in TV mode. See the ‘Connection of external equipment’ section.
1. Press the MENU button and then D / E button to select the
SPECIAL menu.
2. Press the G button and then D / E button to select Input.
3. Press the G button and then D / E button to select TV, AV, S-Video,
Component1, Component2, RGB PC, DVI PC.
SPECIAL
TV/AV
Input
G
Child lock
Language
Power indicator
Transparency
Zoom
TV
AV
S-Video
Component1
Component2
RGB PC
DVI PC
Reset
E
MENU
Prev.
AV: VCR connected to the RCA jack on the side panel.
S-Video: S-VIDEO VCR connected to the S-VIDEO sockets on
the side panel set
Component1: DTV connected to the Component 1 sockets on
the back of set.
Component2: DVD connected to the Component 2 (480i, 576i)
sockets on the back of set.
RGB PC: PC connected to the RGB socket on the set
DVI PC: PC connected to the DVI socket on the set
4. Press the MENU button to save.
MENU
OK
You can select the Inputs can be set for TV, AV, S-Video,
Component1, Component2, RGB PC, DVI PC mode by pressing
the TV/AV button.
In AV, S-Video, Component1, Component2, RGB PC, DVI PC
mode, press the PR +/- or NUMBER buttons to return to TV mode.
22
SPECIAL Menu
Child lock
SPECIAL
The TV can be set so that the remote control handset is needed to
control it. This feature can be used to prevent unauthorized viewing.
1. Press the MENU button and then D / E button to select the
SPECIAL menu.
2. Press the G button and then D / E button to select Child
lock.
Input
Child lock
Language
Power indicator
Transparency
Zoom
Reset
E
MENU
Prev.
SPECIAL menu
SPECIAL
Input
Child lock
Off
On
G
Language
Power indicator
Transparency
Zoom
Reset
E
MENU
Prev.
3. Press the G button and then D / E button to select Off or On.
4. Press the MENU button to save.
With the lock on, the display Controls locked appears on the
screen if any button on the side panel is pressed while viewing the
TV.
Power indicator
Use this function to set the power indicator on the front side of the
TV to ON or OFF. If you set OFF, it will go off after 15 seconds. If
you set ON at any time, the power indicator will automatically be
turned on.
1. Press the MENU button and then D / E button to select the
SPECIAL menu.
2. Press the G button and then D / E button to select Power
indicator.
3. Press the G button and then D / E button to select Off or On.
4. Press the MENU button to save.
MENU
Transparency
To adjust the transparency of the OSD menu screen.
1. Press the MENU button and then D / E button to select the
SPECIAL menu.
2. Press the G button and then D / E button to select
Transparency.
SPECIAL
Input
Child lock
Language
0
Power indicator
Transparency
G
Zoom
Reset
E
MENU
Prev.
3. Press the G button and then press the F / G button to make
appropriate adjustments.
4. Press the MENU button to save.
Note :
.
The adjustment range of Transparency is 0~100.
23
SPECIAL Menu
SPECIAL
Input
Child lock
Language
Power indicator
Transparency
Zoom
Reset
E
MENU
Prev.
Picture Size Zoom
Use this function to zoom in the screen.
When you turn the TV off and on again, the default screen size will
be restored.
1. Press the MENU button and then D / E button to select the
SPECIAL menu.
2. Press the G button and then D / E button to select Zoom .
SPECIAL menu
SPECIAL
Zoom
0
Input
H Position 0
Child lock
V Position 0
Language
Power indicator
Transparency
Zoom
G
Reset
E
MENU
Prev.
3. Press the G button and then D / E button to select Zoom.
Press the F / G button to enlarge or reduce the picture size.
4. Press the D / E button to select H Position or V Position.
Press the F / G button to to adjust the picture position while in
larged picture mode.
5. Press the MENU button to save.
Note : If the zooming value is set to '0', vertical and horizontal positioning cannot be adjusted.
Reset
MENU
Use this function to reset the set to the factory default. However,
language selection will not be initialized.
1. Press the MENU button and then D / E button to select the
SPECIAL menu.
2. Press the G button and then D / E button to select Reset.
SPECIAL
Input
To set
Child lock
Language
Power indicator
Transparency
Zoom
Reset
G
E
MENU
Prev.
3. Press the G button to start Reset.
4. Repeatedly press the MENU button to return to normal TV
viewing.
Note : This function operates in every mode.
24
SCREEN Menu
Picture format
SCREEN
You can watch TV in various picture formats; Full, 4:3, Spectacle,
Zoom1 and Zoom2.
ARC
Auto-configure
Clock
Phase
1. Press the MENU button and then D / E button to select the
SCREEN menu.
2. Press the G button and then D / E button to select ARC.
Position
MENU
SCREEN
ARC
G
Auto-configure
Clock
Phase
Full
4:3
Spectacle
Zoom1
Zoom2
Prev.
SCREEN menu
Position
MENU
Prev.
3. Press the G button and then D /
desired picture format.
4. Press the MENU button to save.
E
button to select your
You can also select Full, 4:3, Spectacle, Zoom1 or Zoom2 with
the ARC button on the remote control.
ARC
Full
When your TV receives the wide screen signal, it will lead you to
adjust the picture horizontally or vertically, in a linear proportion, to
fill the entire screen fully.
4:3
It will lead you to view a picture with an original 4:3 aspect ratio,
with gray bars appearing at both the left and right sides.
Spectacle
When your TV receives the wide screen signal, it will lead you to
adjust the picture horizontally, in a linear proportion, to fill the entire
screen.
MENU
Zoom1
Choose Zoom1 when you want to view the picture without any
alteration. However, the top and bottom portions of the picture will
be cropped.
Zoom2
Choose Zoom2 when you want the picture to be altered, both vertically extended and cropped. The picture taking a halfway trade
off between alteration and screen coverage.
Note :
a. In PIP/POP/PBP mode, ARC function isn’t available.
b. In RGB, DVI modes, you can only select 1:1 and Full screen.
25
SCREEN Menu
SCREEN
Auto adjustment (RGB [PC] mode only)
ARC
Auto-configure
Clock
Automatically adjusts picture position and minimizes image shaking.
Phase
Position
MENU
Prev.
1. Press the MENU button and then D / E button to select the
SCREEN menu.
2. Press the G button and then D / E button to select Auto Configure.
SCREEN menu
SCREEN
ARC
Auto-configure
G
To Set
Clock
Phase
Position
Prev.
MENU
3. Press the G button to start Auto-configure.
If the position of the image is still not correct, try Auto adjustment again.
4. Repeatedly press the MENU button to return to normal TV
viewing.
Clock and Phase (RGB [PC] mode only)
If the picture isn’t clear after auto adjustment and especially that
characters are still trembling, adjust the picture phase manually. To
correct the screen size, adjust Clock.
MENU
1. Press the MENU button and then D / E button to select the
SCREEN menu.
2. Press the G button and then D / E button to select Clock or
Phase.
3. Press the G button and then press the F / G button to make
appropriate adjustments.
SCREEN
ARC
Auto-configure
Clock
G
50
Phase
Position
MENU
Prev.
4. Press the MENU button to save.
Note :
a. The adjustment range of Phase is 0~100.
b. The adjustment range of Clock is 0~100.
26
SCREEN Menu
SCREEN Position (RGB [PC] mode only)
SCREEN
ARC
Auto-configure
1. Press the MENU button and then D / E button to select the
SCREEN menu.
2. Press the G button and then D / E button to select Position.
Clock
Phase
Position
SCREEN
MENU
ARC
Auto-configure
D
Clock
F
Phase
SCREEN menu
G
E
Position
MENU
Prev.
G
Horizontal
50
Vertical
47
Prev.
3. Press the G button and then D / E or F / G button until desired
position is achieved.
4. Press the MENU button to save.
MENU
27
PIP/POP/PBP operation
PIP/POP/PBP
On/Off
PIP/POP/PBP mode
1. Press the MENU button and then D / E button to select the
PIP/POP/PBP menu.
2. Press the G button and then D / E button to select On/Off.
Source
Size
Image
Sound
PIP/POP/PBP
Position
Swap
On/Off
G
Source
MENU
Prev.
PIP/POP/PBP menu
Size
Image
Off
PIP
POP
PBP
Sound
Position
Swap
MENU
Prev.
3. Press the G button and then D /
POP or PBP.
4. Press the MENU button to save.
E
button to select Off, PIP,
PIP
After selecting PIP in the PIP On/Off menu,
the following menu items can be adjusted.
POP
After selecting POP in the POP On/Off
menu, the following menu items can be
adjusted.
PBP
After selecting PBP in the PBP On/Off
menu, the following menu items can be
adjusted.
PIP/POP/PBP
You can also select PIP, POP, PBP or Off with the PIP/POP/PBP
button on the remote control.
MENU
Sub Picture Size
OK
To adjust the size of the PIP/PBP screen. (PIP: Small, Medium,
Large / PBP : Full, 4:3)
1. Press the MENU button and then D / E button to select the
PIP/POP/PBP menu.
2. Press the G button and then D / E button to select Size.
3. Press the G button and then D / E button to adjust the sub picture size.
PIP/POP/PBP
On/Off
Source
Size
G
Small
Medium
Large
Image
Sound
Position
WIN.SIZE
Swap
MENU
Prev.
4. Press the MENU button to save.
You can also adjust this function with the WIN.SIZE button on the
remote control.
28
PIP/POP/PBP operation
Source
PIP/POP/PBP
On/Off
To select an input signal for PIP/POP/PBP.
Inputs can be set for TV, AV, S-Video, Component1, Component2,
RGB PC, DVI PC mode. AV mode is used when a video cassette
recorder (VCR), or other equipment is connected to the set.
Source
Size
Image
Sound
Position
Swap
MENU
Note : When a VCR is connected via the aerial socket the set is
used in TV mode. See the ‘Connection of external equipment’ section.
Prev.
PIP/POP/PBP menu
1. Press the MENU button and then D / E button to select the
PIP/POP/PBP menu.
2. Press the G button and then D / E button to select Source.
PIP/POP/PBP
TV
AV
S-Video
Component1
Component2
RGB PC
DVI PC
On/Off
Source
G
Size
Image
Sound
Position
Swap
MENU
Prev.
3. Press the G button and then D / E button to select TV, AV, S-Video,
Component 1, Component 2, RGB PC, DVI PC.
AV: VCR connected to the RCA jack on the side panel.
S-Video: S-VIDEO VCR connected to the S-VIDEO sockets on
the back panel set
Component1: DTV connected to the Component 1 sockets on
the back of set.
Component2: DVD connected to the Component 2 sockets on
the back of set.
RGB PC: PC connected to the RGB socket on the set
DVI PC: PC connected to the DVI socket on the set
4. Press the MENU button to save.
MENU
OK
<Table of PIP/POP/PBP Function Support>
Main Screen
TV
AV
TV
X
X
X
X
X
Sub-Screen
S-Video COMPONENT1 COMPONENT2 RGB-PC DVI-PC
AV
X
X
X
X
X
S-Video
X
X
X
X
X
COMPONENT 1
X
X
X
X
X
COMPONENT 2
X
X
X
X
X
RGB-PC
DVI-PC
PIP INPUT
X
X
You can also adjust this function with the PIP INPUT button on the
remote control.
29
PIP/POP/PBP operation
PIP/POP/PBP
On/Off
Image
To adjust the image of the PIP/POP/PBP screen.
1. Press the MENU button and then D / E button to select the
PIP/POP/PBP menu.
2. Press the G button and then D / E button to select Image.
Source
Size
Image
Sound
Position
Swap
MENU
PIP/POP/PBP
Prev.
PIP/POP/PBP menu
On/Off
Contrast 100
Source
Brightness 64
Size
Image
G
Color
64
Tint
50
Sound
Position
Swap
MENU
3. Press the
G
Prev.
button and then
D
/
E
button to select Contrast ,
Brightness,Color or Tint (NTSC only).
4. Press the F / G button to make appropriate adjustments
5. Press the MENU button to save.
Note : When PIP input source, only Color and Tint is TV mode.
Sound
To turn the PIP/POP/PBP sound on/off
1. Press the MENU button and then D / E button to select the
PIP/POP/PBP menu.
2. Press the G button and then D / E button to select Sound.
PIP/POP/PBP
On/Off
Off
Source
On
Size
Image
Sound
G
Position
Swap
MENU
MENU
Prev.
3. Press the G button and then D /
4. Press the MENU button to save.
E
button to select Off or On.
Moving the sub Picture
To adjust the position to PIP screen.
1. Press the MENU button and then D / E button to select the
PIP/POP/PBP menu.
2. Press the G button and then D / E button to select Position.
PIP/POP/PBP
On/Off
Source
Size
Image
Sound
Position
G
Swap
3. Press the G button and then D / E button until desired position is achieved.
The sub picture moves up/down or left/right.
4. Press the MENU button to save.
You can also adjust this function with WIN.POSITION button on the
remote control.
30
PIP/POP/PBP operation
Swap
PIP/POP/PBP
On/Off
To switch the main-screen and sub-screen in PIP/POP/PBP mode.
Source
Size
1. Press the MENU button and then
PIP/POP/PBP menu.
D
/
E
button to select the
Image
Sound
Position
Swap
PIP/POP/PBP
To set
On/Off
MENU
Prev.
Source
PIP/POP/PBP menu
Size
Image
Sound
Position
Swap
MENU
G
Prev.
2. Press the G button and then D / E button to select Swap.
3. Press the G button to switch the main-screen and sub-screen.
4. Press the MENU button to save.
PIP
SWAP
SWAP
POP
PBP
SWAP
MENU
Press the SWAP button to exchange the main and sub pictures.
Programme selection for sub picture
The sub picture programme selection is available when the sub picture is TV mode. Press the PIP PR -/+ buttons to select a programme for the sub picture.
PIP PRPIP PR+ SWAP
31
Teletext (This feature is not available in all countries.)
Teletext (or TOP text) is an optional function, therefore only a set
with the teletext system can receive the teletext broadcast.
Teletext is a free service broadcast by most TV stations which gives
up-to-the-minute information on news, weather, television programmes, share prices and many other topics.
The teletext decoder of this TV can support the SIMPLE, TOP and
FASTEXT systems. SIMPLE (standard teletext) consists of a number of pages which are selected by directly entering the corresponding page number. TOP and FASTEXT are more modern
methods allowing quick and easy selection of teletext information.
Switch on/off
Press the TEXT button to switch to teletext.
The initial page or last page appears on the screen.
Two page numbers, TV station name, date and time are displayed
on the screen headline. The first page number indicates your selection, while the second shows the current page displayed.
Press the TEXT button to switch off teletext. The previous mode
reappears.
TEXT
SIMPLE text
MENU
Page selection
1. Enter the desired page number as a three digit number with the
NUMBER buttons. If during selection you press a wrong number, you must complete the three digit number and then reenter the correct page number.
2. The D / E button can be used to select the preceding or following page.
Programming a colour button in LIST mode
If the TV is in SIMPLE text, TOP text or FASTEXT mode, press the
M button to switch to LIST mode.
MODE
M
32
Four teletext page numbers of your choice can be colour coded and
easily selected by pressing the corresponding coloured button on
the remote control.
1. Press a coloured button.
2. Using the NUMBER buttons, select the page you wish to programme.
3. Press the OK button. The selected page is stored as the selected page number, blinking once to confirm this. From now on,
you can select this page with the same coloured button.
4. The three other coloured buttons are programmed in this way.
Teletext (This feature is not available in all countries.)
TOP text (This feature is not available in all countries.)
The user guide displays four fields-red, green, yellow and blue at
the bottom of the screen. The yellow field denotes the next group
and the blue field indicates the next block.
Block / group / page selection
1. With the blue button you can progress from block to block.
2. Use the yellow button to proceed to the next group with automatic overflow to the next block.
3. With the green button you can proceed to the next existing
page with automatic overflow to the next group.
Alternatively the D button can be used.
4. The red button permits to return to previous selection.
Alternatively the E button can be used.
Direct page selection
Corresponding to the SIMPLE teletext mode, you can select a page
by entering it as a three digit number using the NUMBER buttons in
TOP mode.
FASTEXT
The teletext pages are colour coded along the bottom of the screen
and are selected by pressing the corresponding coloured button.
Page selection
1. Press the i button to select the index page.
2. You can select the pages which are colour coded along the bottom line with the same coloured buttons.
3. Corresponding to the SIMPLE teletext mode, you can select a
page by entering its three digit page number with the NUMBER
buttons in FASTEXT mode.
4. The D / E button can be used to select the preceding or following page.
PIP PR-
PIP INPUT
PIP PR+ SWAP
INDEX
i
33
Teletext (This feature is not available in all countries.)
Special teletext functions
REVEAL
Press this button to display concealed information, such as
solutions of riddles or puzzles.
Press this button again to remove the information from the
display.
SIZE
Selects double height text.
Press this button to enlarge the top half of the page.
Press this button again to enlarge the bottom half of the
page.
Press this button again to return to the normal display.
UPDATE
Displays the TV picture on the screen while waiting for the
new teletext page. The display
will appear at the top
left hand corner of the screen. When the updated page is
available then display
will change to the page number.
Press this button to view the updated teletext page.
OK
PIP INPUT
SWAP
HOLD
Stops the automatic page change which will occur if a teletext page consists of 2 or more sub pages. The number of
sub pages and the sub page displayed is, usually, shown
on the screen below the time. When this button is pressed
the stop symbol is displayed at the top left-hand corner of
the screen and the automatic page change is inhibited.
To continue press this button again.
MIX
Displays the teletext pages superimposed on the TV picture.
To switch the TV picture off press this button again.
MIX
34
TIME
TIME
When viewing a TV programme, press this button to display
the time at the top right hand corner of the screen. Press
this button again to remove the display. In the teletext
mode, press this button to select a sub page number. The
sub page number is displayed at the bottom of the screen.
To hold or change the sub page, press the RED / GREEN,
D / E or NUMBER buttons.
Press this button again to exit this function.
Connection of external equipment
You can connect additional equipment, such as VCRs, camcorders
etc. to your set.
Here shown may be somewhat different from your set.
Aerial socket
1. Connect the RF out socket of the VCR to the aerial socket on
the back of the set.
2. Connect the aerial cable to the RF aerial in socket of the VCR.
3. Store the VCR channel on a desired programme number using
the ‘Manual programme tuning’ section.
4. Select the programme number where the VCR channel is
stored.
5. Press the PLAY button on the VCR.
VCR
DVD input sockets
1. Connect the DVD output sockets (Y Cb Cr, Y Pb Pr, Y B-Y R-Y
or Y PB PR) of the DVD to the COMPONENT 1, 2 IN sockets (Y
PB PR) of the set.
2. Connect the audio cable from the DVD to DVD INPUT AUDIO
sockets of the set.
3. Press the TV/AV or INPUT button to select Component 1, 2.
4. Press the PLAY button on the DVD.
The DVD playback picture appears on the screen.
DVD Player
Note :
a. Component1 : DTV , DVD source
b. Component2 : DVD source.
DTV in sockets
1. Connect the SET TOP outputs to the COMPONENT1 IN sockets (Y PB PR) of the set.
2. Connect the audio cable from the SET TOP to the AUDIO sockets of the set.
3. Press the TV/AV or INPUT button to select Component 1.
Receriver
35
Connection of external equipment
S-VIDEO
S-Video/Audio in sockets (S-Video)
AUDIO L / MOLO
VIDEO
When connecting an S-VIDEO VCR to the S-VIDEO socket, the
picture quality will be further improved.
R
1. Connect the S-Video socket of the VCR to the S-VIDEO socket of the set.
2. Connect the audio cable from the S-VIDEO VCR to the AV /
AUDIO L/R sockets of the set.
3. Select S-Video by pressing the TV/AV button repeatedly.
4. Press the PLAY button on the VCR.
The VCR playback picture appears on the screen.
AV
S-VIDEO VCR
PC in socket
COMPONENT1
RS-232C
OUTPUT
AC INPUT
DVI INPUT
REMOTE
CONTROL
RGB INPUT
COMPONENT2
AUDIO INPUT
L
RS-232C
OUTPUT
VIDEO INPUT
PERSONAL COMPUTER
R
AUDIO INPUT
1. Connect the signal cable from the TV output socket of the PERSONAL COMPUTER to the RGB PC IN or DVI PC IN socket of
the set.
2. Connect the audio cable from the PC to the AUDIO INPUT
sockets of the set.
3. Press the INPUT or TV/AV button to select RGB PC or DVI PC.
4. Switch on the PC, and the PC screen appears on the set.
The set can be operated as the PC monitor.
Note : If you have an Apple macintosh, connect the VGA desktop
block (not supplied) from the 3 row 15 pin to 2 row 15 pin with the
signal cable and connect the VGA desktop block to the Macintosh.
R
AUDIO L / MOLO
VIDEO
S-VIDEO
Audio/Video in sockets
AV
VCR
36
1. Connect the audio/video out sockets of the VCR to audio/video
in sockets of the set.
2. Press the TV/AV button to select AV.
3. Press the PLAY button on the VCR.
The VCR playback picture appears on the screen.
Note : If you have a mono VCR, connect the audio cable from the
VCR to the AUDIO L/MONO socket of the set.
Displayable Monitor Specification
RGB Mode
MODE
Resolution
Horizontal
Frequency
(KHz)
1
640x350
31.47
70.80
2
720x400
31.47
70.80
31.47
59.94
37.50
75.00
5
43.27
85.00
6
37.88
60.32
46.88
75.00
53.67
85.06
49.73
74.55
48.36
60.00
60.12
75.03
68.68
85.00
44.77
59.86
63.98
60.02
79.98
75.02
3
4
7
640x480
800x600
8
9
832x624
10
11
1024x768
12
13
1280x720
14
Vertical
Frequency
(Hz)
1280x1024
15
16
1360x768
47.72
59.80
17
1600x1200
75.00
60.00
(Synchronization input form : separate)
Note :
a. If the set is cold, there may be a small “flicker”
when the set is switched on. This is normal,
there is nothing wrong with the set.
b. If possible, use the 1,360x768@60Hz video
mode to obtain the best image quality for your
LCD monitor. If used under the other resolutions,
some scaled or processed pictures may appear
on the screen. If used to PC vertical frequency
85Hz, some noise can be seen when PIP is on.
In this case, set the PC vertical frequency to
60Hz.
c. Some dot defects may appear on the screen,
like Red, Green or Blue spots. However, this
will have no impact or effect on the monitor
performance.
d. Do not press the LCD screen with your finger
for a long time as this may produce some temporary distortion effects on the screen.
e. When the PC screen appears on the set, a
message may appear on the screen, and the
message will differ according to the Window
system version (Win98, 2000). If a message
appears click “Next” until the message finishes.
f. If the message “Out of range” appears on
the screen, adjust the PC as in the
‘Displayable Monitor Specification’ section.
MODE 1~17 : D-Sub
MODE 1~14,16 : DVI-D
37
External Control Device Setup
Connect the RS-232C input jack to an external control device (such as a computer or an A/V control
system) and control the set’s functions externally.
RS-232C input socket
1. Connect the serial port of the control device to the RS-232C jack on the set.
2. RS-232C connection cables are not supplied with the set.
3. The set’s remote control handset and side panel controls (except main power) will not be functional if the set is controlled by a PC computer or other external device.
RS-232C
OUTPUT
RS-232C
OUTPUT
RS-232C
OUTPUT
RS-232C
OUTPUT
RS-232C
OUTPUT
RS-232C
OUTPUT
D-Sub 9-pin male
No.
1
2
3
4
5
6
7
8
9
Pin name
No connection
RXD (Receive data)
TXD (Transmit data)
DTR (DTE side ready)
GND
DSR (DCE side ready)
RTS (Ready to send)
CTS (Clear to send)
No Connection
1
5
9
6
Set ID
Use this function to specify a monitor ID number.
Refer to ‘Real Data Mapping’. See page 40.
1. Press the MENU button and then use the D / E button to select
the SPECIAL menu.
2. Press the G button and then use D / E button to select Set ID.
3. Press the G button and then use F / G button to adjust Set ID
to choose the desired monitor ID number.
Note : The adjustment range of Set ID is 0 ~ 99.
Communication Parameters
• Baud rate : 9600 bps (UART)
• Parity : None
• Communication code : ASCII code
* Use a crossed (reverse) cable.
38
• Data length : 8 bits
• Stop bit : 1 bit
SPECIAL
D
Set ID
G
ID
MENU
Prev.
___ ___
External Control Device Setup
Command Reference List
COMMAND 1 COMMAND 2
DATA
(Hexadecimal)
01. Power
02. Input Select
03. Volume Mute
04. Volume Control
05. Contrast
06. Brightness
07. Color
08. Tint
09. Sharpness
10. PIP/PBP/POP ON/OFF
11. PIP Position
12. Balance
13. ACC
14. PIP/PBP/POP SOURCE
k
k
k
k
k
k
k
k
k
k
k
k
k
k
a
b
e
f
g
h
i
j
k
n
q
t
u
y
0~1
0~8
0~1
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0~3
0~3
0 ~ 64
0~3
0~8
Transmission / Receiving Protocol
OK Acknowledgement
Transmission
[Command2][ ][Set ID][ ][OK][Data][x]
[Command1][Command2][ ][Set ID][ ][Data][Cr]
* The Monitor transmits ACK (acknowledgement)
based on this format when receiving normal data.
At this time, if the data is data read mode, it indicates present status data. If the data is data write
mode, it returns the data of the PC computer.
* [Command 1] : First command. (j or k)
* [Command 2] : Second command.
: You can adjust the set ID to choose
* [Set ID]
desired monitor ID number in
Special menu. Adjustment range is
1~ 99. When selecting Set ID ‘0’,
every connected TV set is controlled. Set ID is indicated as decimal (1~99) on menu and as Hexa
decimal (0x0~0x63) on transmission/receiving protocol.
: To transmit command data.
* [DATA]
Transmit 'FF' data to read status
of command.
: Carriage Return ASCII code
* [Cr]
‘0x0D’
: ASCII code Space (0x20)’
*[ ]
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The Monitor transmits ACK (acknowledgement)
based on this format when receiving abnormal
data from non-viable functions or communication
errors.
Data 1 : Illegal Code
2 : Not supported function
3 : Wait more time
39
External Control Device Setup
01. Power On (Command : a)
G
To control Power On/Off of the Set.
04. Volume Control(Command : f)
G
To control On/Off of the volume.
Transmission
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
[k][f][ ][Set ID][ ][Data][Cr]
Data
0 : Power Off
1 : Power On
Acknowledgement
Acknowledgement
[a][ ][Set ID][ ][OK][Data][x]
G
To show the status of Power On/Off.
[k][a][ ][Set ID][ ][FF][Cr]
0 : Power Off
[f][ ][Set ID][ ][OK][Data][x]
Data
Transmission
Data
Data
Min : 00H ~ Max : 64H
(Hexadecimal code)
Min : 00H ~ Max : 64H
05. Contrast (Command : g)
1 : Power On
G
Acknowledgement
[a][ ][Set ID][ ][OK][Data][x]
* The Monitor transmits ACK (acknowledgement)
based on this format when receiving normal data.
At this time, if the data is data read mode, it indicates present status data. If the data is data write
mode, it returns the data of the PC computer.
To adjust screen contrast.
You can also adjust the contrast in the Picture
menu.
Transmission
[k][g][ ][Set ID][ ][Data][Cr]
Data
Min : 00H ~ Max : 64H
*Refer to ‘Real data mapping’ as shown below.
Acknowledgement
02. Input Select (Command : b) (Main Picture
Input)
G
To select input source for the Set.
You can also select an input source using the
INPUT button on the remote control.
[g][ ][Set ID][ ][OK][Data][x]
06. Brightness (Command : h)
G
Transmission
[k][b][ ][Set ID][ ][Data][Cr]
Data 0 : TV
2 : AV
3 : S-Video
4 : Component 1
5 : Component 2
6 : RGB PC
8 : DVI PC
Acknowledgement
To control On/Off of the Volume Mute.
Transmission
[k][e][ ][Set ID][ ][Data][Cr]
Data 0 : Volume Mute On (Volume Off)
1 : Volume Mute Off (Volume On)
Acknowledgement
[e][ ][Set ID][ ][OK][Data][x]
Data 0 : Volume Mute On (Volume Off)
1 : Volume Mute Off (Volume On)
40
[k][h][ ][Set ID][ ][Data][Cr]
Data Min : 00H ~ Max : 64H
* Refer to ‘Real data mapping’ as shown below.
[h][ ][Set ID][ ][OK][Data][x]
5 : Component 2
6 : RGB PC
8 : DVI PC
03. Volume Mute(Command : e)
G
Transmission
Acknowledgement
[b][ ][Set ID][ ][OK][Data][x]
Data 0 : TV
2 : AV
3 : S-Video
4 : Component 1
To adjust screen brightness.
You can also adjust the brightness in the Picture
menu.
* Real data mapping
0 : Step 0
A : Step 10 (SET ID 10)
F : Step 15 (SET ID 15)
10 : Step 16 (SET ID 16)
64 : Step 100
* Tint,Balance :-50 ~ +50
External Control Device Setup
07. Color (Command : i) (TV,AV only)
G
To adjust the screen color.
You can also adjust the color in the Picture menu.
11. PIP Position(Command : q)
To adjust PIP position.
Transmission
G
Transmission
[k][q][ ][Set ID][ ][Data][Cr]
[k][i][ ][Set ID][ ][Data][Cr]
Data
Min : 00H ~ Max : 64H
(Hexadecimal code)
Data 0 : Bottom of the right side on screen
1 : Bottom of the left side on screen
2 : Top of the left side on screen
3 : Top of the right side on screen
Acknowledgement
Acknowledgement
[i][ ][Set ID][ ][OK][Data][x]
[q][ ][Set ID][ ][OK][Data][x]
Data
Data 0 : Bottom of the right side on screen
1 : Bottom of the left side on screen
2 : Top of the left side on screen
3 : Top of the right side on screen
Min : 00H ~ Max : 64H
08. Tint (Command : j) (TV,AV -NTSC only)
G
To adjust the screen tint.
You can also adjust the tint in the Picture menu.
G
Transmission
Data
Red: 00H ~ Green: 64H
(Hexadecimal code)
Acknowledgement
[j][ ][Set ID][ ][OK][Data][x]
[k][t][ ][Set ID][ ][Data][Cr]
Data
Min : 00H ~ Max : 64H
(Hexadecimal code)
Acknowledgement
[t][ ][Set ID][ ][OK][Data][x]
Red: 00H ~ Green: 64H
09. Sharpness (Command : k) (TV,AV only)
G
To adjust the screen Balance.
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
Data
12. Balance(Command : t)
To adjust the screen Sharpness.
You can also adjust the sharpness in the Picture
menu.
Data
Min : 00H ~ Max : 64H
13. ACC(Command : u)
To adjust the screen color temperature.
Transmission
G
Transmission
[k][u][ ][Set ID][ ][Data][Cr]
[k][k][ ][Set ID][ ][Data][Cr]
Data 0 : Normal (9300K)
2 : Warm (6500K)
PC : 0,2,3,
Data
Min : 00H ~ Max : 64H
(Hexadecimal code)
1 : Cool
3 : User
AV : 0,1,2
Acknowledgement
Acknowledgement
[u][ ][Set ID][ ][OK][Data][x]
[k][ ][Set ID][ ][OK][Data][x]
Data
Min : 00H ~ Max : 64H
Data 0 : Normal
2 : Warm
1 : Cool
3 : User
14. PIP/PBP/POP SOURCE(Command : y)
10. PIP/PBP/POP ON/OFF(Command : n)
G
To control PIP/PBP/POP On/Off of the Set.
Transmission
[k][n][ ][Set ID][ ][Data][Cr]
Data 0 : OFF
2 : PBP
1 : PIP
3 : POP
[k][y][ ][Set ID][ ][Data][Cr]
Data Min : 00H ~ Max : 08H
(Hexadecimal code)
Acknowledgement
[n][ ][Set ID][ ][OK][Data][x]
Data 0 : OFF
2 : PBP
To select the sub-screen source.
Data 0 : TV
5 : Component 2
2 : AV
6 : RGB PC
3 : S-video
8 : DVI PC
4 : Component 1
Transmission
G
Acknowledgement
1 : PIP
3 : POP
[y][ ][Set ID][ ][OK][Data][x]
Data Min : 00H ~ Max : 08H
41
Programming the Remote control
G The remote control is a multi-brand or universal remote control. It can be programmed to operate most remote-controllable
devices of other manufacturers.
Note that the remote control may not control all models of
other brands.
Programming a code into a remote mode
MODE
POWER
PSM
PR
1. Test your remote control.
To find out whether your remote control can operate the component without programming, turn on the component such as a
VCR and press the corresponding MODE button (VCR) on the
remote control, while pointing at the component. Test the
POWER and PR +/- buttons to see if the component responds
properly. If not, the remote requires programming to operate the
device.
2. Turn on the component to be programmed, then press the corresponding MODE button on the remote control.
3. Press the PSM and PIP PR- buttons simultaneously, the remote
control is ready to be programmed for the code.
OK
4. Enter a code number using the number buttons on the remote.
Programming code numbers for the corresponding component
can be found on the following pages. Again, if the code is correct,
the device will turn off.
5. Press the PIP PR- button to store the code.
PIP PR-
6. Test the remote control functions to see if the component
responds properly. If not, repeat from step 2.
42
Programming Codes
VCRs
Brand
Codes
Brand
Codes
AIWA
AKAI
034
016
125
072
031
012
035
028
108
003
031
005
065
112
108
012
034
059
006
029
036
129
003
034
031
107
132
012
004
043
031
031
012
040
043
012
048
130
KENWOOD
014
047
001
101
034
003
017
040
031
067
012
069
101
027
031
003
033
101
045
013
013
049
151
034
024
012
048
043
053
066
133
013
063
031
031
067
101
013
AMPRO
ANAM
AUDIO DYNAMICS
BROKSONIC
CANON
CAPEHART
CRAIG
CURTIS MATHES
DAEWOO
DAYTRON
DBX
DYNATECH
ELECTROHOME
EMERSON
FISHER
FUNAI
GE
GO VIDEO
HARMAN KARDON
HITACHI
INSTANTREPLAY
JCL
JCPENNY
JENSEN
JVC
043 046 124
146
033
023
037
031
103
039 043
129
033
040
033
007
108
116
135
041
010 064
110 111
117 119
023 039 043
053
027
035
101
153
010
LG (GOLDSTAR)
LLOYD
LXI
MAGIN
MAGNAVOX
MARANTZ
MARTA
MATSUI
MEI
MEMOREX
017
031
037
131
008
025
034
046
138
009
033
109
136
045
018
063
033
033
013
066
063 072
144 147
MTC
MULTITECH
NEC
026 034
137 150
NORDMENDE
OPTONICA
PANASONIC
MGA
MINOLTA
MITSUBISHI
PENTAX
015 033
101
031 033 043
050 055 060
150 152
PHILCO
PHILIPS
PILOT
PIONEER
Brand
034 039 043
048
012 013 020
106 114 123
PORTLAND
PULSAR
QUARTZ
QUASAR
RCA
009 013 014
034 101 106
033 034 041
068
031 033 067
030
033
010
034
102
046
020
020
051
REALISTIC
RICO
RUNCO
SALORA
SAMSUNG
014 031
053 072
134 139
059
045 046
059 061
040
034
023 039 043
054
070 074 083
140 145
020 031 033
034 067
033 034 054
071 101
021 048
SANSUI
SANYO
SCOTT
SEARS
010
SHARP
SHINTOM
SONY
SOUNDESIGN
STS
SYLVANIA
SYMPHONIC
TANDY
Codes
108
072
011
033
013
040
107
145
003
031
053
058
148
014
032
105
113
125
022
003
102
017
131
003
013
031
101
031
024
003
056
077
034
013
031
067
034
010
014
066
020
041
109
147
008
033
054
Brand
075
033
062
140
145
034
063
144
010 014
034 040
101
TATUNG
TEAC
TECHNICS
TEKNIKA
THOMAS
TMK
TOSHIBA
TOTEVISION
UNITECH
VECTOR RESEARCH
040 102 104
107 109 112
115 120 122
043 048 135
007 010 014
134
037 112 129
VICTOR
VIDEO CONCEPTS
VIDEOSONIC
WARDS
YAMAHA
ZENITH
Codes
039
034
031
019
101
034
006
008
059
040
040
012
048
012
040
003
031
053
012
034
058
043
039 043
033 070
031 033 034
013 042 047
082 112 131
101
034 046
013
033
054
034
048
072
017
034
131
039
056
080
024
040
043
101
00 009
014 017 020
042 073 081
054 149
009 031 052
057 058 076
078 149
033 034 059
034
CATV
CATV
Brand
Codes
Brand
Codes
ABC
003
046
112
014
005
026
092
007
007
065
080
019
023
020
057
032
072
008
052
GOLDEN CHANNEL
HAMLIN
HITACHI
HOSPITALITY
JERROLD
030
049
052
070
002
009
074
001
037
033
010
100
028
015
073
016
044
100
006
AJIN
ANTRONIK
ARCHER
CABLE STAR
CENTURION
CENTURY
CITIZEN
COLOUR VOICE
COMBANO
COMTRONICS
DIAMOND
EAGLE
EASTERN
ELECTRICORD
GE
GEMINI
GI
004 039 042
052 053
007 014 024
090
081
030
030 040
062 066
022 025 054
074
LG (GOLDSTAR)
M-NET
MACOM
MAGNAVOX
MEMOREX
MOVIE TIME
NSC
OAK
PANASONIC
PARAGON
PHILIPS
050 055
055
077
003 004 008
010 052 069
106 101 005
012 064 079
032
028 038 071
Brand
PIONEER
POST NEWS WEEK
PRUCER
PTS
PULSAR
RCA
REGAL
REGENCY
REMBRANT
RK
SAMSUNG
SCIENTIFIC ATLANTA
031 037 053
047
012 013 020
SHERITECH
SIGNAL
SIGNATURE
Codes
Brand
Codes
065
034
076
016
059
011
073
100
047
049
057
025
091
102
003
043
022
030
052
SL MARX
SPRUCER
STARCOM
STARGATE
SYLVANIA
TADIRAN
TAEKWANG
TAIHAN
TANDY
TEXSCAN
TOCOM
TOSHIBA
UNIKA
UNITED CABLE
UNIVERSAL
030
047
002
008
067
030
110
105
017
029
039
100
007
004
005
026
012
087
100
085 090
051 052 063
048 071 072
074
050
107 030 068
011 041 042
045 046
VIEWSTAR
ZENITH
078
004 008 009
030
067
040 056
014
053
007
027
015
088
114
024
014
032
018
089
060
024
035
086
093
43
Programming Codes
STB
Brand
Codes
Brand
ALPHASTAR DSR
AMPLICA
BIRDVIEW
BSR
CAPETRONICS
CHANNEL MASTER
123
050
051
053
053
013
036
008
054
050
005
011
141
024
038
093
097
122
089
EUROPLUS
FUJITSU
CHAPARRAL
CITOH
CURTIS MATHES
DRAKE
DX ANTENNA
ECHOSTAR
ELECTRO HOME
126 129
014 015 018
055
009 012 077
145
006 007 010
052 112 116
046
040
094
098
056
057
095
099
076
058
096
100
Codes
114
017
133
GENERAL INSTRUMENT 003
031
HITACHI
139
HOUSTON TRACKER
033
057
HUGHES
068
HYTEK
053
JANIEL
060
JERROLD
061
KATHREIN
108
LEGEND
057
LG
001
LUTRON
132
LUXOR
062
MACOM
010
065
021
134
004
059
140
037
104
Brand
022 027
016 029
101
039 051
147
144
059 063 064
Codes
MEMOREX
NEXTWAVE
NORSAT
057
028
069
PACE SKY SATELLITE 143
PANASONIC
060
PANSAT
121
PERSONAL CABLE 117
PHILIPS
071
PICO
105
PRESIDENT
019
PRIMESTAR
030
PROSAT
072
RCA
066
REALISTIC
043
SAMSUNG
123
SATELLITE SERVICE CO 028
085
SCIENTIFIC ATLANTA
032
SONY
103
124 125
070
Brand
Codes
STARCAST
SUPER GUIDE
TEECOM
041
020
023
088
137
002
016
044
078
101
135
115
128
081
091
142
TOSHIBA
UNIDEN
102
110 111
UNIDEN
VIEWSTAR
WINEGARD
ZENITH
106
074
124 125
026 075 087
090 107 130
127
025 042 043
045 048 049
079 080 086
136
146
082 083 084
120
035 047 057
138
Audio
Brand
AIWA
Codes
014
125
230
AKAI
163
ANAM
003
059
217
BURMECTER
252
CARVER
086
CLARION
199
DAEWOO
027
102
DENON
015
FANTASIA
071
FINEARTS
022
FISHER
089
LG(GOLDSTAR)
001
087
190
211
HAITAI
034
HARMAN/KARDON 068
INKEL
037
078
122
152
157
189
225
247
028 070 096
129 139 229
014 017 023
106 189 216
235 236
Brand
Codes
JVC
KEC
KENWOOD
004
185
038
170
215
030
045
014
100
175
179
201
214
238
103
111
002
034
097
049
104
107
046
013
048
133
158
007
142
104
KOHEL
NAD
LOTTE
053 060 084
148 198 221
075 130 143
099
021
107
191
212
035
024
108
192
239
188
029
110
210
058
079
149
153
158
207
226
062
095
150
154
159
222
227
069
121
151
155
160
224
243
222
LXI
MAGNAVOX
MARANTZ
MCINTOSH
MCS
MEMOREX
NAD
ONKYO
OPTIMUS
PANASONIC
PENNEY
013
186
050
171
222
046
016
172
176
180
202
219
240
141
187
067 089
197 206
036
173
177
181
208
223
098
174
178
183
213
232
018 020 025
041 081 090
112
Brand
Codes
PHILIPS
PIONEER
026
039
065
115
113
080
092
103
124
193
204
011
019
106
031
072
156
206
005
044
118
012
076
162
166
205
254
010
185
101
QUASAR
RCA
RCX
REALISTIC
SAMSUNG
SANSUI
SANYO
SCOTT
SHARP
SHERWOOD
SONY
TAEKWANG
040 041 047
056 057 132
140
033 064 113
220 241 251
TEAC
TECHNICS
112
042
091
123
106
145
194
244
135
083
186
032
082
184
209
006
045
126
020
077
163
167
231
143
043
093
127
253
063
094
250
146
195
245
138
234
182
203
246
144
Brand
Codes
TOSHIBA
THE
VICTOR
WARDS
YAMAHA
147 218
137
061
088 131
089
054 055 066 092
199
051 052
117 119
199 200
158
109
248
073
105
164
168
233
114
249
074
161
165
169
242
085 106 136
187 237
113 128 134
DVD
Brand
Codes
Brand
Codes
Brand
Codes
Brand
Codes
APEX DIGITAL
DENON
GE
HARMAN KARDON
JVC
LG
022
020 014
005 006
027
012
001 010 016 025
MAGNAVOX
MARANTZ
MITSUBISHI
NAD
ONKYO
PANASONIC
013
024
002
023
008 017
003 009
PHILIPS
PIONEER
PROCEED
PROSCAN
RCA
SAMSUNG
013
004
021
005
005
011
SONY
THOMPSON
TOSHIBA
YAMAHA
ZENITH
007
005
019
009
010
44
026
006
006
015
006
008
018
016 025
Note
45
Note
46
Troubleshooting check list
Symptoms
No picture, no sound
Sound OK, poor picture
Picture OK, poor sound
Picture blurred
Lines or streaks in picture
Poor reception on some channels
No colour
Poor colour
Remote control does not work
Incorrect position
Vertical bars or stripes on background
Horizontal noise
Signal Cable message appears
Check these items and try to
adjust these
The mains plug-(plugged in and
switched on)
Is the TV switched on
Try another channel (weak signal)
Check aerial (plugged into TV?)
Check aerial (broken lead?)
Check aerial
Check for local interference
Adjust contrast
Adjust brightness
Adjust colour
Adjust volume
Check the batteries in remote control
Check Audio/Video sockets (VCR only)
Auto-configure or adjust the H/V position
Auto-configure or adjust Clock
Auto-configure or adjust Clock Phase
Is the Signal Cable connected or loose
47
Download PDF

advertising