LG GBW-H10N Owner’s Manual

Add to My manuals
15 Pages

advertisement

LG GBW-H10N Owner’s Manual | Manualzz
Blu-ray Disc Rewriter
English
Français
Español
Português
GBW-H10N
CAUTION : The laser used in the Blu-ray Disc Rewriter can damage your eyes.
Do not attempt to open the cover.
To reduce the risk of electric shock, do not remove the cover (or back).
There are no user-serviceable parts inside.
Refer servicing to qualified service personnel.
Use of controls or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
WARNING : To reduce the risk of fire or electric shock, do not expose this appliance
to rain or moisture
Industry Canada requirement
This class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC COMPLIANCE STATEMENT
Note : This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an Authorized Service Center for help.
• FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• This Blu-ray Disc Rewriter is for use only with UL listed personal computers that
have installation instructions detailing user-installation of card cage accessory.
i
This product is manufactured to comply with the radio interference requirements
of EEC DIRECTIVE 89/336/EEC, 93/68/EEC and 73/23/EEC.
CAUTION : CLASS 3B VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN.
AVOID EXPOSURE TO THE BEAM.
ADVARSEL : KLASSE 3B SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING.
UNDGÅ UDSÆTTELSE FOR STRÅLING.
ADVARSEL : KLASSE 3B SYNLING OG USYNLIG LASERSTRÅLING NÅR
DEKSEL ÅPENS. UNNGÅ EKSPONERING FOR STRÅLEN.
VARNING : KLASSE 3B SYNLING OCH OSYNLIG LASERSTRÅLNING NÄR DENNAL
DEL ÄR ÖPPNAD. STRÅLEN ÄR FARLIG.
VARO! : KURSSI 3B NÄKYVÄ JA NÄKYMÄTÖN AVATTAESSA OLET
ALTTIINA LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEN.
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
CLASE 1
CLASSE 1
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
PRODUCTO LÁSER
PRODOTTO LASER
The appliance is not intended for use by young children or infirm persons without
supervision.
ii
Contents
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
System Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Location and Function of Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Installing the Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Device Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
How to Use the Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
■
■
■
■
Microsoft® and Windows® are trademarks registered in the United States and other
countries by the Microsoft Corporation.
DVD Logo is a trademark of DVD Format/Logo Licensing Corp., registered in U.S.,
Japan and other countries.
BD Logo is a trademark registered in U.S., Japan and other countries.
The company names and product names written in this manual are trademarks or
registered trademarks of the respective companies.
Features
•
•
•
•
•
•
Enhanced-IDE (ATAPI) interface.
Power tray loading and ejection of disc. (The disc can also be ejected manually.)
Combination BD-ROM, BD-R, BD-RE, DVD-ROM, DVD-R/RW, DVD-R DL,
DVD+R/RW, DVD+R DL, DVD-RAM, CD-ROM, CD-R/RW, Drive functions
into one drive.
Supports Regional Playback Control Phase II for DVD-Video.
Supports Windows XP SP2 Home Edition/Professional/Media Center Edition.
Automatic buffer underrun error prevention technology.
Package Items
Item
Quantity
- Blu-ray Disc Rewriter
- IDE Interface cable (with Ferrite Core)
- BD-R SL Blank Disc
- Application Software
(Power2Go BD/Instant Burn BD,
Power Back Up BD, Power Producer, PowerDVD)
- Owner’s Manual
1
1
1
1
1
1
Important Precautions
Follow these precautions when handling the drive or discs.
• Please take notice that the manufacturer of this equipment does not offer any
warranty against data loss due to inappropriate installation or handling, or direct
or indirect damages.
• Please take notice that the manufacturer will bear no responsibility for direct or
indirect damages caused by the use of this product or its malfunction.
• Please take notice that the manufacturer will bear no responsibility for damage to
data caused by this product.
• Please backup (copy) all important data as a protection against data loss.
• Avoid placing the drive in a location subject to:
- high humidity, high temperature, excessive dust, mechanical vibration,
direct sunlight
We recommend using the drive in a horizontal or vertical position.
Do not use it in tilted position.
• Don’t move the drive suddenly from a cold place to a warm one or raise the room
temperature suddenly. Condensation may occur, causing abnormal operation.
• Make sure to remove the disc before moving the drive. The disc may become damaged, causing data loss.
• Be careful to prevent foreign objects, such as liquids or metal, from entering the
drive. In case a foreign object enters the drive, please consult the dealer where
the drive was purchased.
• Don’t interrupt the electric power while the drive is operating.
• When connecting two IDE devices to the Primary or Secondary connectors, make
sure that the two devices are not configured as both Master, or both Slave.
If they are both set the same, Windows may fail to run or recognize the drives.
• The total length of the IDE cable should be no more than 18 inches
(about 45 cm).
2
System Environment
Computer
This unit can be operated in the system environment explained here.
CPU: Pentium D 3.2GHz or faster, Memory: 1024MB or greater.
GPU: nVIDIA GeForce 6600GT/7600GT/7900GT, Memory: 256MB or
greater, ATIx1800/x1900 Memory 256MB or greater. The device driver
for COPP(Certified Output Protection Protocol) is necessary.
Display
Resolution: 1024x768 pixel or greater. (When the digital output of
DVI/HDMI is used, GPU for the HDCP/HDMI and HDCP/HDMI
monitor are necessary.) Recommended: 1920x1080 pixel.
Hard disk
25GB or more free space.
(The free space needed for writing depends on the quantity of data.)
Interface
Enhanced-IDE interface (as Primary Slave, Secondary Master or Slave)
Drive bay
5.25-inch half-height bay required
Power
+5V/+12V power socket required
Software Required OS Windows XP SP2 (Home Edition/ Professional/ Media Center Edition)
BD-R, BD-RE, DVD-R, BD-R : Mitsubishi Kagaku Media, Verbatim, TDK are recommended.
DVD-RW, DVD+R,
BD-RE : Mitsubishi Kagaku Media, Verbatim, TDK are recommended.
DVD+RW, DVD±R DL, DVD-R : Maxell, Mitsubishi Kagaku Media, Taiyo Yuden are recommended.
DVD-RAM, CD-R,
DVD-RW : JVC, Mitsubishi Kagaku Media are recommended.
CD-RW,
DVD+R : Mitsubishi Kagaku Media, Verbatim are recommended.
discs
DVD+RW : Mitsubishi Kagaku Media, Verbatim are recommended.
DVD±R DL : Mitsubishi Kagaku Media, Verbatim are recommended.
DVD-RAM : Maxell, Panasonic are recommended.
CD-R : LG, Mitsubishi Kagaku Media, Verbatim, Taiyo Yuden or TDK
discs are recommended.
CD-RW : LG, Ricoh, Mitsubishi Kagaku Media, Verbatim discs are recommended.
System
requirements
* Compatibility problem in write/read function may occur with media depending on the media
manufacturing quality.
* There may be some cases when motion picture playback is not smooth depending on bit rate.
❏ Occasionally CD-R and CD-RW discs written by a CD-R/RW drive cannot be read by other CD drives*.
These unreadable discs may need to be read using the CD-R/RW drive they were created with
*
The disc written using the CD-R/RW drive might not be readable by CD-ROMs other than Multi-read
compatible (UDF compatible) CD-ROMs
Multiread compatible (UDF compatible) CD-ROMs are:
1. CD-ROMs that can read low reflectance.
2. CD-ROMs that support Packet Write.
❏ Please note: Certain software (i.e. particularly those including Video playback) may require
a considerably increased specification PC to give acceptable results. While this Blu-ray
Disc Rewriter can read DVD-video or BD-MV(BD-ROM) discs, decoding them to display on
your pc’s monitor requires separate MPEG, H.264 or VC-1 decoding that is done by separate hardware (either an MPEG, H.264 or VC-1 decoder card or MPEG, H.264 or VC-1
decoding done by your video card), or separate software that you install to do MPEG,
H.264 or VC-1 decoding. For further details, refer to the documentation that comes with
MPEG, H.264 or VC-1 software.
3
Software
Install the appropriate CD/DVD/BD Recording Authoring Software before using this unit.
* Please uninstall any previous CD/DVD/BD burning software you may have loaded on
your PC in order to prevent possible compatibility issues. Once you have installed the
application software, you may (if you wish) begin to reinstall previous software, taking
note for errors.
We recommend using the drive with the latest software as some problems encountered
when using the drive can be solved by updating the software.
Location and Function of Controls
Front Panel
1 2
Rear Panel
3
12 3 4
4
5
1. Digital Audio Output Connector
1. Disc Tray
This connector is not supported.
2. Emergency Eject Hole
2. Analog Audio Output Connector
3. Drive activity indicators
This connector is not supported.
The LED used to indicate the operation of
Blu-ray Disc Rewriter.
3. Jumper Connector
This jumper determines whether the drive is
configured as a master or slave. Changing the
master-slave configuration takes effect after
power-on reset.
4. Eject Button
4. IDE Interface Connector
Connect to the IDE (Integrated Device
Electronics) Interface using a 80-conductor flat
IDE cable.
NOTE : Do not connect or disconnect the cable
when the power is on, as this could cause a short
circuit and damage the system. Always turn the
power OFF when connecting or disconnecting
this cable.
5. Power Connector
4
Installing the Drive
Before installing the drive, please note the following points.
■ You will need the following:
• A screw driver of a suitable size to fit the securing screws for the drive unit.
• The manual for the computer, so you can find the mounting positions for the IDE
controller cable.
■ Turn off all peripheral appliances of the computer and the computer itself, and disconnect their power cords from the wall sockets.
■ Discharge any static electricity on your person by touching the computer covers, etc.
Removing the Computer Cover
Make sure all peripheral devices of the computer and the computer itself are turned off,
and then remove the cover. Refer to the manual for the computer for details about
removing the cover.
NOTE : There may be sharp edges inside the computer so take care to avoid injury.
Mounting the Drive
1. Remove the 51/4″ drive bay panel from the computer. Refer to the manual for the
computer for details.
2. Insert the drive unit into the bay. Do not apply excessive pressure to the cables inside
the computer.
3. Secure the drive with the screws. If there is not enough space behind the drive, connect the IDE and other cables before securing the drive.
READ
WRITE
READ
WRITE
NOTE : This is a general installation guide.
If your PC hardware appears different,
please consult your hardware manual for
installing peripheral devices.
Jumper Setup
Before installation, set the jumper connector on the rear panel.
The drive can be connected as the Master or Slave on an EIDE (ATAPI) interface. When
several (up to four) EIDE devices are connected, each must be set in a unique way.
Specific knowledge of hardware and software is necessary to install the drive.
SL: Slave
MA: Master
NOTE : If two peripheral devices with the same
settings are both connected to the Primary or to
the Secondary EIDE bus, the host computer may
fail to run or may malfunction. Careful attention is
necessary.
CS: Cable Select (CSEL)
5
NOTE : Only one jumper should be installed on the jumper connector.
If more than one jumper is installed, the drive may malfunction or be damaged.
Master/Slave setting is determined by jumper installation on the Jumper Connector.
The following table shows the possible jumper settings.
Name
C
S
Function
MA
(Master)
Drive set as Master
SL
(Slave)
Drive set as Slave
CS
(Cable Select)
Drive mode set by CSEL on the host IDE
interface
S
L
M
A
If you use CSEL setting, the MASTER/SLAVE setting will be made automatically,
depending on the hardware configuration. For more details refer to the manual of your
computer.
PC Connection
The Blu-ray Disc Rewriter connects to the motherboard of the host computer using an
IDE interface cable. You may connect the Blu-ray Disc Rewriter as a Slave or Master
device, depending on your computer.
To Install as a Master Drive
To install the drive as a Master, the jumper can be left as supplied from the factory.
Master drive
(Booting hard disk)
DIGITAL
AUDIO
ANALOG
AUDIO
DG
R G L
CS M
S L A
INTERFACE
39
40
POWER
1
2
Primary
connector
Master drive
Master drive
(Booting hard disk) (Blu-ray Disc Rewriter)
(Jumper left as Master)
Master drive
(Blu-ray Disc Rewriter)
(Jumper left as Master)
+5 GND
+12
- OR -
DIGITAL
AUDIO
ANALOG
AUDIO
DG
Motherboard
Secondary
connector
CS M
S L A
INTERFACE
39
40
POWER
+5 GND
+12
ANALOG
AUDIO
DG
Primary
connector
R G L
1
2
DIGITAL
AUDIO
R G L
CS M
S L A
INTERFACE
39
40
POWER
1
2
+5 GND
+12
Slave
drive
(Other IDE
drive)
Secondary
connector
NOTE : A hard disk is normally installed as the Primary Master on the EIDE (ATAPI)
interface. Other EIDE peripheral devices such as hard drives and Blu-ray Disc Rewriters
are then set differently.
6
To Install as a Slave Drive
To install the drive as a Slave, change the jumper setting on the rear panel to SL.
Master drive
(Booting hard disk)
DIGITAL
AUDIO
ANALOG
AUDIO
DG
R G L
CS M
S L A
INTERFACE
39
40
POWER
1
2
+5 GND
+12
Slave drive
(Blu-ray Disc
Rewriter)
(Jumper set to
Slave)
Master drive
(Other IDE drive)
Master drive
(Booting hard disk)
- OR -
DIGITAL
AUDIO
ANALOG
AUDIO
DG
R G L
CS M
S L A
INTERFACE
39
40
POWER
1
2
DIGITAL
AUDIO
ANALOG
AUDIO
DG
Primary
connector
+5 GND
+12
R G L
CS M
S L A
INTERFACE
39
40
POWER
1
2
+5 GND
+12
Slave drive
(Blu-ray Disc
Rewriter)
(Jumper set
to Slave)
Secondary
connector
Connecting the Power Connector
Connect the power cable from the computer’s power supply to the socket on the drive unit,
fitting the connector firmly into the power in connector. If there is no spare power cable
available in the computer, you will have to purchase a splitter cable of a suitable type.
NOTE : Improper connection may damage
the drive and void the warranty. Generally,
the power connector can only fit one way.
Beveled edge up
Connecting the Interface Connector
Connect the 80-conductor IDE cable to the back of the Blu-ray Disc Rewriter, making
sure the coloured (red) stripe on the IDE cable is connected to pin 1 on the Blu-ray Disc
Rewriter (Pin 1 is closest to the Power Connector).
NOTE : Generally, the IDE connector is
keyed and will only fit one way.
Pin1
Red-edge
Ferrite Core
7
Device Drivers
When using Windows XP SP2 Home Edition/Professional/Media Center Edition,
no special device driver is required. Your system, upon Power On and bootup after
installing and connecting the new Blu-ray Disc Rewriter, will recognize and load
native software drivers automatically.
Please consult the following internet sites:
http://www.lgservice.com (then choose your country from the list)
For Windows XP Users
■
■
■
In order to ensure normal drive operation, please check the following:
• The drive is displayed in
Windows XP : [Control Panel]-([Performance and Maintenance])-[System][Hardware]-[Device Manager]-[DVD/CD-ROM-drives]
If the drive is not recognized by your computer, please check the following
items.
• If an
indicator is displayed on the IDE ATA/ATAPI controllers in [Control
Panel]-([Performance and Maintenance])-[System]-[Hardware]-[Device
Manager], you will need to contact your PC’s manufacturer or the motherboard’s manufacturer and get the appropriate IDE controller driver.
Run Add New Hardware in Control Panel to let PC search again for new
device.
8
How to Use the Discs
When using any discs, don’t attach any stickers or labels to the discs. It could cause
read and write errors, but data on the disc may be lost due to damage to the disc itself.
The Discs in this unit operate at a very high
speed! DO NOT use damaged, cracked or
warped discs. The drive’s optical unit may
be damaged if they break.
DO NOT use non-standard discs. NON-standard discs may not play or store data
properly.
Emergency Eject
This drive has a feature that allows the disc to be ejected manually if this becomes
necessary such as failure of the drive or a power outage.
NOTE: Don’t use this feature except in an emergency.
1)
Turn the power to OFF.
2)
Poke a fine-tipped object (such as a straightened heavy duty paper clip) into the
small hole above the eject button. The front door will pop open and the disk tray will
come partway out.
3)
Pull the front door to open it all the way, then grip the disc tray between thumb and
forefinger and gently pull it straight out.
NOTE: This feature is a last measure to be
used only in an emergency.
Using it excessively will cause malfunction.
* If you cannot get a good grip on the disc tray with your fingers, use a steel binder clip
or spring clamp to pull it out.
9
Troubleshooting
Before Requesting Service
Before calling for service, check this list.
•
The drive doesn’t have power.
• Is the power supply cable from the host computer plugged in?
• Is the Power Connector to the drive securely attached?
•
The system doesn’t start.
• Are the Primary and Secondary connections and the Master and Slave settings
correct?
• Is the total length of the IDE cable 18 inches or less?
• Is each connector completely attached?
Other connections may have been knocked lose while installing the drive.
•
Cannot Read or Write Discs.
• Is the condition of everything else in the system (CPU, hard disc, and others) as it
should be? (See system environment page 3.)
• Does the CD, DVD or BD disc have dirt or scratches?
• Did a screen saver or other application operate while writing to the disc?
• Is there enough free space on the CD, DVD and BD disc?
• Does writing fail even using the simulation test for CD or DVD disc?
• Is the disc loaded in the drive with the read/write surface facing the right direction?
(label up)
• Is the drive installed in the correct orientation?
• Was the drive or disc moved from a low temperature environment to a high temperature environment? (There is a possibility of condensation on the lens in the drive or
on the surface of the disc.)
When you call for service, be prepared to give as much information as possible of your
system, environment, and the specific problem. (What happened? When? How long?
What was going on? Were there any error messages displayed? etc.)
Please Note: Since this product supports Regional Playback Control Phase II for
DVD-Video with CSS, a certain MPEG decoder card or Software without regional code
setting may cause this drive not to read DVD-Video with CSS discs. This Drive enables
you to change the regional code up to 5 times.
10
Specifications
Items
General
Supported Discs *1
Disc Diameter
Host Interface
Read/Write Speed *5
Performance
Mounting direction
Data transfer rate
*Sustained
*Burst(ATAPI)
Average Access
Time (1/3 Stroke)
Buffer capacity
MTBF
BD/DVD/CD
BD-ROM(Single/Dual), BD-R(Single), BD-RE(Single)*2, DVD-ROM
(Single/Dual), DVD-RW, DVD-R(Ver.2.1 for General), DVD-R Dual
layer, DVD+RW, DVD+R, DVD+R Double layer, DVD- RAM(Ver.2.2)*3,
CD-Digital Audio & CD-Extra, CD-Plus, CD-ROM, CD-ROM XAReady, CD-I FMV, CD-TEXT, CD-Bridge, CD-R, CD-RW*4, Photo-CD
(Single & Multi-Session), Video CD, DVD-Video.
12cm/ 8cm (8cm disc can be used only with drive placed
horizontally. 8cm BD-R/RE is not supported.)
E-IDE/ATAPI
Read :
Write :
BD-ROM (SL) : 4.8x max.
BD-R (SL) : 2x, 4x
BD-ROM (DL) : 4x max.
BD-RE (SL) : 2x
BD-R (SL) : 4.8x max.
DVD-R : 2x, 4x, 8x, 12x
BD-RE (SL) : 2x
DVD-R (DL): 2x, 4x
DVD-R/RW/ROM(SL/DL) :
DVD-RW : 1x, 2x, 4x, 6x
DVD-RAM: 2x, 3x, 3x-5x (Ver.2.2) 10x/ 10x/16x/8x max.
DVD-R DL: 8x max.
DVD+R : 2.4x, 4x, 8x, 12x
DVD-RAM : 2x, 3x, 3x-5x (Ver.2.2)
DVD+R (DL): 2.4x, 4x
DVD-Video : 8x max.
DVD+RW : 2.4x, 4x, 6x, 8x
DVD+R/RW : 10x / 10x max.
CD-R : 4x, 8x
DVD+R DL : 8x max.
CD-RW : 4x, 10x
CD-R/RW/ROM : 40x max.
CD-DA(DAE) : 40x max.
Horizontal/Vertical
BD-ROM : 21579 Kbytes/s (4.8x max)
DVD-ROM : 22160 Kbytes/s (16x max)
CD-ROM : 6000 Kbytes/s (40x max)
16.6 Mbytes/s (PIO Mode 4), (Multiword-DMA Mode 2)
33.3 Mbytes/s (Ultra-DMA Mode 2)
CD-ROM: 170ms (Typical), DVD-ROM : 180ms (Typical)
DVD-RAM : 190ms (Typical), BD-ROM : 170ms (Typical)
4 Mbytes
100000 Power On Hours (Duty Cycle 10%)
Environmental When operating
Level
When not operating
Temperature: 5 °C to 45 °C Humidity: 15% to 85% R.H.
Temperature: -30 °C to 60 °C Humidity: 10% to 90% R.H.
Electrical
DC 5V, DC 12V
Power
The disc of the cartridge type is not supported.
*2
BD-RE: The disc of version 1.0 is not supported. The BD-R DL, BD-RE DL disc is not supported.
*3
DVD-RAM: Writing to 12x disc is not supported.
*4
CD-RW: Writing to Ultra speed/Ultra speed plus disc is not supported.
*5
There might be some cases when this drive can not satisfy the best performance depending on the
conditions of the disc, the drive, and the recording format.
* This Rewriter cannot support the HD-DVD discs. Do not insert HD-DVD discs into the Rewriter.
* The drive’s appearance and specifications may change without prior notice.
*1
11
Copyright © 2006
Caution!
LG Electronics U.S.A. Inc.
1000 Sylvan Ave.
Englewood Cliffs NJ 07632
U. S. A.
or http://www.lgusa.com
LG Electronics Canada Inc.
550 MATHESON Blvd. East
Mississauga. Ontario L4Z4G3 Canada
LG Electronics Deutschland GMBH
Jakob-Kaiser-Straße 12,
D-47877 Willich, Germany
LG Electronics U. K. Ltd.
LG House, 250 Bath Road,
Slough Berkshire SL1 4DX
United Kingdom
Goldstar France E.U.R.L
Paris Nord II 22, Avenue des
Nations-B.P.50372 VILLEPINTE
95945 ROISSY CDG CEDEX France
LG Electronics Italia S.P.A.
Centro Direzione “IL Quadrate” Via
Modigliani, 20090 Segrate (MI) Italy
LG Electronics España
Complejo Europa Empressaries
(Edif.Bruselas) Ctra. N-VI 28230 Las
Rozas Madrid Spain
LG Electronics Australia Pty Ltd.
2 Wonderland drive, Eastern creek,
NSW 2766
or http://www.lge.com.au
LG Electronics Portugal S.A.
Quinta da Fonte – Edifício D. Amélia
Rua Vítor Câmara, nº2, Piso 2
2700-229 Paço d´ Arcos, Portugal
ou www.lge.pt
The disc rotates at high speed in the drive unit.
Use of worn, damaged, or non-standard discs can
adversely affect the drive and cause the disc to
shatter or crush while in use.
Disc crush can only occur when you use a damaged
disc in the drive. It is an extremely rare occurrence,
but there are steps which can be taken to prevent it.
Always check your discs before inserting them
into the drive.
1. Take care not to use worn, cracked, damaged,
warped or poor quality discs, as this may
cause damage to your drive.
2. Check the clear plastic on the center of the
disc, cracks here are the main cause of disc
crush.
3. Do not play discs which are a non-standard
(I.e. non-circular)shape, such as heart shaped
discs, or discs in the shape of a business
card.
How can you keep your discs from becoming
damaged?
1. When not in use, remove discs from the drive.
2. Keep discs in the packaging supplied with
them and out of direct sunlight and away from
heat sources.
Excessive vibration or a sudden jolt to the drive
during operation may cause a malfunction.
Avoid exposing the drive to sudden changes in
temperature as it may cause condensation to collect
inside the drive.
Please visit www.lgservice.com and install the program,
“LG ODD Online F/W update.” By using the program,
you can automatically check the latest information about
FirmWares and update the FirmWare.
P/NO. MFL31705803
Ver. A
©2006
Made by

advertisement

Related manuals

Download PDF

advertisement