LG | 23CAV42K-BL | LG 23CAV42K-B Owner’s Manual

English
OWNER'S MANUAL
CLOUD MONITOR
(LED LCD MONITOR)
Please read the safety information carefully before using the product.
CLOUD Monitor(LED LCD Monitor) Model
23CAV42K
www.lg.com
2
Table of Contents
TABLE OF CONTENTS
English
ENG
3
ASSEMBLING AND
PREPARING
27 PRODUCT SPECIFICATION
28
Preset Mode
3
Unpacking
28
Power Indicator
4
Parts and buttons
6
Lifting and moving the Monitor
6
Setting Up the Monitor set
6
- Attaching the Stand Base
7
- Mounting on a table
7
- Adjusting the angle
8
- Adjusting the stand height
8
- Using the Kensington locking device
9
- Detaching the stand base
9
- Detaching the stand body
10
- Swivel stand
10
- Using the Pivot function
11
- Installing the wall mount plate
11
- Mounting on a wall
13 USING THE MONITOR SET
13
Connecting Input Signal Cable
13
- D-SUB IN connection - PC
14
- DVI connection
15
Connecting LAN/Peripherals
15
- LAN connection
16
- Peripheral device connection
17
- Self Image Adjustment
18 CUSTOMIZING SETTINGS
19
Customizing Settings
19
- Menu Settings
20
- PICTURE
21
- COLOR
22
- DISPLAY
23
- OTHERS
24
- VOLUME
25 TROUBLESHOOTING
29 PROPER POSTURE
29
Proper posture for using the monitor
30 USING CLOUD SOLUTION
ASSEMBLING AND PREPARING
3
ASSEMBLING AND PREPARING
ENG
English
Unpacking
Please check whether all the components are included in the box before using the product. If there are
missing components, contact the retail store where you purchased the product. Note that the product and
components may look different from those shown here.
User Manual/Card
Stand Base
Power Cord
Adaptor
15-pin D-SUB Signal Cable
(This cable is not included in all
counties)
CAUTION
Only use an approved LG power adapter.
yy
Damage caused by other power adapters is not covered by warranty.
yy
NOTE
Note that the components may look different from those shown here.
yy
Without prior notice, all information and specifications in this manual are subject to change to improve
yy
the performance of the product.
To purchase optional accessories, visit an electronics store or online shopping site or contact the retail
yy
store where you purchased the product.
4
ASSEMBLING AND PREPARING
Parts and buttons
English
ENG
Input Connectors
(See p.16 )
Power Indicator
yyLED On : Power is on
yyLED Off: Power is off
(Power Button)
Front Side Buttons
1
1
Input Connectors (See p.13 to 16)
ASSEMBLING AND PREPARING
Button
MENU
Description
Activates the main menu.
Locks/unlocks the OSD screen.
yy To lock the OSD screen, press and hold the MENU button
for several seconds. The "OSD LOCKED" message will be
displayed and the screen will be locked.
yy To unlock the OSD screen, press and hold the MENU
button again for several seconds. The "OSD UNLOCKED"
message will be displayed and the screen will be unlocked.
VOL
Adjust the volume of the monitor.(only works in Cloud mode)/the left arrow key.
CLOUD
Disconnects the connection when the key is pressed for a few seconds while in Cloud
mode;the right arrow key.
AUTO
To adjust the monitor settings, press the AUTO button on the MONITOR SETUP OSD
menu (only supported for analog signal).
For optimal screen display, use the following resolution.
Optimal Resolution
1920 x 1080
INPUT
Allows selection of the input signal.
yy If you connect the monitor to a computer using a D-SUB cable, select either the
CLOUD or D-SUB input signal.
yy The initial input signal is D-SUB.
EXIT
Exits the OSD menu.
yy D-SUB Input: Power On/Off
yy CLOUD Input
Monitor Off: Press the power button once then the monitor will be turned off after 5
seconds.
CLOUD Off: Press the power button twice then the monitor and CLOUD connection
will be disabled.
CLOUD On: Press the power button.
Power Indicator
When the monitor is in operating mode, the power indicator
will turn Red (on mode).
When the monitor is in power saving mode, the power indicator will blink Red.
ENG
English
OSD Lock/Unlock
Functions
(Power Button)
5
6
ASSEMBLING AND PREPARING
English
ENG
Lifting and moving the
Monitor
Please heed the following information when
moving the monitor.
CAUTION
yyAvoid touching the screen at all times, as this
may result in damage to the screen or pixels .
Setting Up the Monitor set
Attaching the Stand Base
1 Place the monitor's screen face down.
CAUTION
To protect the screen from scratches, cover
yy
the surface with a soft cloth.
2 Check the position (at the front and rear) of
It is recommended to move the Monitor in
yy
the box or packing material that the Monitor
originally came in.
Before moving or lifting the Monitor,
yy
disconnect the power cord and all cables.
Hold the top and bottom of the Monitor frame
yy
firmly. Make sure not to hold the transparent
part area.
the stand body, then mount the stand base on
the stand body as shown in the figure.
Stand Body
Stand Base
When holding the Monitor, the screen should
yy
face away from you to prevent the screen
from scratches.
3 Using a coin, turn the screw clockwise to secure the stand base.
When transporting the Monitor, do not
yy
expose the Monitor to jolts or excessive
vibration.
When transporting the Monitor, keep the
yy
Monitor upright, never turn the Monitor on its
side, or tilt towards the left or right.
Stand Base
ASSEMBLING AND PREPARING
Adjusting the angle
1 Lift the monitor and place it on the table in an
1 Place the monitor mounted on the stand base
upright position.
Install at least 100 mm away from the wall to
ensure sufficient ventilation.
in an upright position.
2 Adjust the angle of the screen. The angle of
the screen can be adjusted up to 5° forwards
and 15° backwards for a comfortable viewing
experience.
100 mm
100 mm
100 mm
100 mm
Rear Side
Front Side
WARNING
2 Connect the adaptor to the monitor, then plug
the power cord into the wall outlet.
To avoid injury to the fingers when adjusting
yy
the screen, do not hold the lower part of the
monitor's frame as illustrated below.
Be careful not to touch or press the screen
yy
area when adjusting the angle of the monitor.
3 Press the
(Power) button on the front of the
monitor to turn on the monitor.
CAUTION
Unplug the power cord prior to moving or
yy
installing the monitor. There is risk of electric
shock.
ENG
English
Mounting on a table
7
8
ASSEMBLING AND PREPARING
Adjusting the stand height
English
ENG
1 Place the monitor mounted on the stand base
in an upright position.
2 Remove the tape attached at the bottom rear
of the stand body, then pull out the locking
pin.
Using the Kensington locking
device
The connector for the Kensington lock is located
on the rear of the monitor.
For more information on installation and usage,
refer to the Kensington lock user manual or visit
the website at http://www.kensington.com.
Connect the monitor to the table with the Kensington lock cable.
Stand Body
‌‌
Tape
Locking Pin
3 The height can be adjusted up to 130 mm.
130.0mm
NOTE
CAUTION
Once the pin is removed, it is not necessary
yy
to re-insert it to adjust the height.
WARNING
Do not put your finger beyy
tween the screen and the
base (chassis) when adjusting the screen's height.
Using the Kensington lock is optional. The
yy
accessories can be purchased at your local
electronics store.
ASSEMBLING AND PREPARING
Detaching the stand body
1 Place the monitor's screen face down.
1 Place the monitor's screen face down. To
To protect the screen from scratches, cover the
surface with a soft cloth.
protect the screen from scratches, cover the
surface with a soft cloth.
2 Using a screwdriver, remove the four screws
and detach the stand from the monitor.
2 Using a coin, turn the screw in the stand base
counterclockwise. Detach the stand base from
the stand body.
Stand Body
Stand Base
CAUTION
The components appearing in the illustrayy
tions may look different from the actual product.
Do not carry the monitor upside-down as this
yy
may cause it to fall off its stand, resulting in
damage or injury.
To avoid damaging the screen when lifting
yy
or moving the monitor, only hold the stand or
the plastic cover. This avoids putting unnecessary pressure on the screen.
Only remove the tape and the locking pin
yy
when the monitor is mounted on the stand
base and is in an upright position. Otherwise,
the stand body may protrude, which may
lead to injury.
ENG
English
Detaching the stand base
9
10
ASSEMBLING AND PREPARING
Swivel stand
English
ENG
Image shown may differ from your Monitor
yy
set.
1 Swivel 90 degrees and adjust the angle of the
Monitor set to suit your view.
Using the Pivot function
The pivot function allows you to rotate the screen
90 degrees clockwise.
1 Lift the monitor to its highest height to utilize
the Pivot function.
2 Landscape & Portrait : You can rotate the panel
90° clockwise. Please be cautious and avoid
contact between the monitor head and the
Stand Base when rotating the screen to access
the Pivot function. If the monitor head touches
the Stand Base, then the Stand Base could
crack.
Head
section
Stand
section
3 Be careful with the cables when rotating the
screen.
ASSEMBLING AND PREPARING
11
Mounting on a wall
This monitor has a VESA compatible mount on the
back. Most mounts will require an LG mounting
plate.
Install the monitor at least 100 mm away from the
wall and leave about 100 mm of space at each
side of the monitor to ensure sufficient ventilation.
Detailed installation instructions can be obtained
from your local retail store. Please refer to the
manual to install and set up a tilting wall mounting
bracket.
1 Place the monitor's screen face down. To
protect the screen from scratches, cover the
surface with a soft cloth.
2 Place the wall mount plate on the monitor and
align it with the screw holes on the monitor.
100 mm
3 Using a screwdriver, tighten the four screws to
fix the plate onto the monitor.
100 mm
100 mm
100 mm
Wall Mount Plate
If you intend to mount the Monitor set to a wall,
attach Wall mounting interface (optional parts) to
the back of the set.
When you install the Monitor set using a wall
mounting interface (optional parts), attach it
carefully so it will not drop.
1 Please, Use the screw and wall mount interface
in accordance with VESA Standards.
2 If you use screw longer than standard, the
monitor might be damaged internally.
3 If you use improper screw, the product might be
NOTE
The wall mount plate is sold separately.
yy
For more information on the installation, refer
yy
to the wall mount plate's installation guide.
damaged and drop from mounted position. In
this case, LG Electronics is not responsible for
it.
4 VESA compatible.
5 Please use VESA standard as below.
784.8 mm (30.9 inch) and under
yy
* Wall Mount Pad Thickness : 2.6 mm
* Screw : Φ 4.0 mm x Pitch 0.7 mm x
Length 10 mm
787.4 mm (31.0 inch) and above
yy
* Please use VESA standard wall mount pad
and screws.
ENG
English
Installing the wall mount plate
12
ASSEMBLING AND PREPARING
Model
23CAV42K
English
ENG
VESA (A x B)
Stand Screw
Required Screw
Wall Mount Plate
(Optional)
100 x 100
M4
4
RW120
CAUTION
Unplug the power cord before moving or inyy
stalling the monitor to avoid electric shocks.
Installing the monitor on the ceiling or on a
yy
slanted wall may result in the monitor falling
off, which could lead to injury. Please use
a LG wall mounting bracket when using a
VESA mount. For more information, contact
your local retail store or a qualified installer.
Applying excessive force when fastening
yy
screws may cause damage to the monitor. Damage caused in this way will not be
covered by the product warranty.
Use the wall mounting bracket and screws
yy
that conform to the VESA standard. Damage caused by the use or misuse of inappropriate components will not be covered
by the product warranty.
NOTE
Use the screws specified in the VESA stanyy
dard.
The wall mount kit includes the installation
yy
guide and necessary parts.
The wall mounting bracket is optional. The
yy
accessories can be purchased at your local
retail store.
The length of the screw may differ for each
yy
wall mounting bracket. Ensure the correct
length of the screw is used.
yyFor more information, please refer to the user
manual for the wall mounting bracket.
USING THE MONITOR SET
13
USING THE MONITOR SET
This monitor supports the *Plug and Play
yy
feature.
*Plug and Play: A feature that allows you to
add a device to your computer, without having
to reconfigure anything or install any manual
drivers.
D-SUB IN connection - PC
D-SUB IN transfers analog video signals from the
PC to the monitor.
Connect the monitor to the PC using the provided
15-pin D-SUB signal cable as illustrated below.
NOTE
Apple Adapter
yy
An adapter may be needed for Apple
computers. This adapter can be purchased
from Apple.
ENG
English
Connecting Input Signal Cable
14
USING THE MONITOR SET
DVI connection
English
ENG
Transfers digital video signals from the Cloud Monitor to an extended monitor.
Connect the Cloud Monitor to an extended monitor
using a DVI cable.
CAUTION
Connect the input signal
yy
cable and tighten in the
direction of the arrow. To
prevent disconnection
secure the cable tightly.
Do not press on the screen for a prolonged
yy
time. This may cause image distortion.
Do not display a still image on the screen
yy
for a prolonged time. This may cause image
retention. If possible, use the screen saver.
NOTE
To connect the monitor to a computer, use
yy
the appropriate signal cable (LAN and DSUB).
A converter can be used to convert the DVI-I
yy
input signal to D-SUB input signal.
When connecting the power cord to the outyy
let, use a grounded (3-hole) multi-socket or a
grounded wall outlet.
The monitor may flicker when turned on in an
yy
area of low temperature. This is normal.
Sometimes red, green or blue spots may apyy
pear on the screen. This is normal.
USING THE MONITOR SET
Connecting LAN/Peripherals
Connect the router or switch to the monitor using a
LAN cable as illustrated below.
NOTE
The LAN cable is sold separately.
yy
The following LAN cable type can be used:
yy
Standard: IEEE 802.3 ETHERNET
If a device is connected into the earphone
yy
out port via a LAN cable, you can adjust the
volume with the volume icon on PC taskbar.
Connect the LAN cable and the peripheral
yy
devices prior to booting up the PC.
ENG
English
LAN connection
15
16
USING THE MONITOR SET
Peripheral device connection
NOTE
English
ENG
Connect peripheral devices to the monitor using
USB, microphone and headphone ports.
Peripheral devices are sold separately.
yy
The USB ports on the left and bottom of the
yy
monitor can be used to connect the keyboard, mouse, and other USB devices.
Cables with angled plugs may have clearyy
ance issues, use straight plugs when possible.
Angle Type
Straight Type
Left
NOTE
1
1
Bottom
1
1
Headphones, speakers or microphone may
yy
not work normally, depending on the server
PC settings.
Virtual solutions may affect the functions or
yy
speed of the specific USB storage device.
USING THE MONITOR SET
17
Self Image Adjustment
NOTE
What is "Self Image Adjustment"? This funcyy
tion runs when the monitor is connected for
the first time and performs automatic image
adjustment for each signal (only available for
analog [D-SUB input] signals) to provide an
optimal screen display.
ENG
English
Press the power button on the front to turn on
the monitor. When powered on, the "Self Image
Adjustment" function will run automatically (only
available for analog [D-SUB input] signals).
18
CUSTOMIZING SETTINGS
CUSTOMIZING SETTINGS
English
ENG
1 Press the desired button on the bottom of the Monitor set.
2 Change the value of the menu item by pressing the buttons on the bottom of the Monitor set.
To return to the upper menu or set other menu items, use the up arrow (
) button.
3 Select EXIT to leave the OSD menu.
Monitor set Buttons
CUSTOMIZING SETTINGS
19
Customizing Settings
ENG
English
Menu Settings
1 Press MENU button on the bottom of the Monitor set
to display the MENU OSD.
2 Set the options by pressing the ◄ or ► or ▼
buttons.
3 Select the "NEXT MENU" button to enter the more
option settings.
4 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu items,
use the up arrow ( ) button.
Each option is explained below.
MENU
D-SUB CLOUD
BRIGHTNESS
●
●
CONTRAST
●
●
WIDE/ORIGINAL
Description
To adjust the brightness, contrast of the screen
WIDE
Switch to full screen mode according to input image signal.
●
●
ORIGINAL
Change the input image signal ratio to original.
* This function works only if input resolution is lower than Monitor set ratio (16:9).
RESET
●
●
MENU > NEXT MENU
PICTURE
COLOR
Restore all factory default settings. Press the◄ , ► buttons to reset
immediately.
D-SUB CLOUD
SHARPNESS
GAMMA
COLOR TEMP
DISPLAY
HORIZONTAL
VERTICAL
CLOCK
PHASE
OTHERS
●
●
To adjust the clearness of the screen .
●
●
To customize the color of the screen
●
To adjust the position of the screen
●
To improve the clarity and stability of the screen
LANGUAGE
CLOUD
POWER INDICATOR
CLOUD: Using PC via a network.
yy
Description
●
●
To customize the screen status for a user's operating
environment
20
CUSTOMIZING SETTINGS
PICTURE
English
ENG
1 Press MENU button on the bottom of the Monitor set
to display the MENU OSD.
2 Select the "NEXT MENU" button to enter the more
option settings.
3 Enter to PICTURE by pressing the ▼ button.
4 Set the options by pressing the ◄ or ► or ▼
buttons.
5 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu items,
use the up arrow ( ) button.
Each option is explained below.
MENU > NEXT MENU > PICTURE
SHARPNESS
Description
To adjust the clearness of the screen.
CUSTOMIZING SETTINGS
21
COLOR
ENG
English
1 Press MENU button on the bottom of the Monitor set
to display the MENU OSD.
2 Select the "NEXT MENU" button to enter the more
option settings.
3 Select COLOR by pressing the ► button.
4 Enter to COLOR by pressing the ▼ button.
5 Set the options by pressing the ◄ or ► or ▼
buttons.
6 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu items,
use the up arrow ( ) button.
Each option is explained below.
MENU > NEXT MENU > COLOR
Description
GAMMA
Set your own gamma value. : GAMMA 0, GAMMA 1, GAMMA 2 on the monitor,
high gamma values display whitish images and low gamma values display
blackish images.
COLOR TEMP
CUSTOM
• RED:Set your own red color levels.
• GREEN: Set your own green color levels.
• BLUE:Set your own blue color levels.
Select the screen color.
WARM: Set the screen to warm color temperature (more red).
MEDIUM: Set the screen to medium color temperature.
COOL: Set the screen to cool color temperature (more blue).
22
CUSTOMIZING SETTINGS
DISPLAY
English
ENG
1 Press MENU button on the bottom of the Monitor set
to display the MENU OSD.
2 Select the "NEXT MENU" button to enter the more
option settings.
3 Select DISPLAY by pressing the ► button.
4 Enter to DISPLAY by pressing the ▼ button.
5 Set the options by pressing the ◄ or ► or ▼
buttons.
yyOnly available in D-SUB input mode.
6 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu items,
use the up arrow ( ) button.
Each option is explained below.
MENU > NEXT MENU > DISPLAY
Description
HORIZONTAL
To move image left and right.
VERTICAL
To move image up and down.
CLOCK
To minimize any vertical bars or stripes visible on the screen background.The
horizontal screen size will also change.
PHASE
To adjust the focus of the display. This item allows you to remove any horizontal
noise and clear or sharpen the image of characters.
CUSTOMIZING SETTINGS
23
OTHERS
ENG
English
1 Press MENU button on the bottom of the Monitor set
to display the MENU OSD.
2 Select the "NEXT MENU" button to enter the more
option settings.
3 Select OTHERS by pressing the ► button.
4 Enter to OTHERS by pressing the ▼ button.
5 Set the options by pressing the ◄ or ► or ▼
buttons.
6 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu items,
use the up arrow ( ) button.
Each option is explained below.
DUAL
WEB
MENU > NEXT MENU > OTHERS
Description
LANGUAGE
To choose the language in which the control names are displayed.
CLOUD
Off
CLOUD is disabled in D-SUB input mode.
On
CLOUD is enabled in D-SUB input mode.
POWER
INDICATOR
Use this function to set the power indicator on the bottom side of the monitor to
ON or OFF.If you set OFF, it will go off.
If you set ON at any time, the power indicator will automatically be turned on.
24
CUSTOMIZING SETTINGS
VOLUME
English
ENG
1 Press the VOL button at the bottom of the monitor to
display the VOL OSD menu.
2 Press the ◄ or ► button to adjust the volume.
3 Press the
button to enable or disable Mute.
4 Select EXIT to leave the OSD menu.
Each option is explained below.
DUAL
WEB
MENU > NEXT
MENU > VOLUME
VOLUME
Description
Adjusts the volume (only available in CLOUD input mode).
Troubleshooting
25
TROUBLESHOOTING
Is the monitor's power cord plugged in? yy Check if the power cord is correctly plugged in to the outlet.
Is the power indicator on?
yy Check the power indicator.
Is the power indicator displaying as
red?
yy Adjust the brightness and the contrast.
Is the power indicator blinking?
yy If the monitor is in power saving mode, move the mouse or press any
key on the keyboard to switch the display on.
yy Check if the computer is turned on.
yy This occurs when signals transferred from the PC (video card) are out
of the horizontal or vertical frequency range of the monitor. Please see
the "Product Specification" section of this manual to set the appropriate frequency.
yy This is displayed when the signal cable between the PC and the monitor is missing or disconnected. Check the cable and reconnect.
Is the "OUT OF RANGE" message
displayed?
Is the "CHECK SIGNAL CABLE"
message is displayed?
The "OSD LOCKED" message is displayed.
Is the "OSD LOCKED" message
yy The OSD lock feature is enabled to prevent undesired modification
displayed when the MENU button is
of the OSD settings. Press and hold the MENU button for a couple of
pressed?
seconds to unlock the OSD. (The "OSD UNLOCKED" message will be
displayed.)
The screen retains an image.
Does image sticking occur even
when the monitor is turned off?
yy Displaying a still image for a prolonged time may cause damage to the
screen, resulting in the retention of the image.
yy Use a screen saver to protect the screen when using the monitor for a
prolonged period of time.
NOTE
Vertical Frequency: In order to display an image, the screen must be refreshed dozens of times per
yy
second like a fluorescent lamp. The number of times the screen is refreshed per second is called
vertical frequency or refresh rate and is represented by Hz.
Horizontal Frequency: The time it takes to display one horizontal line is called the horizontal cycle.
yy
The number of horizontal lines displayed in one second
can be calculated by dividing one by the horizontal cycle. This is called horizontal frequency and is
represented by kHz.
ENG
English
Nothing is displayed on the screen
26
Troubleshooting
The image is displayed abnormally.
English
ENG
Does the display area appear uncentered?
Pressing the AUTO button will automatically optimize the screen to the current
display mode.
Does the screen exhibit vertical
lines?
Pressing the AUTO button will automatically optimize the screen to the current
display mode.
Does the screen display horizontal Pressing the AUTO button will automatically optimize the screen to the current
frequencies, or does the text appear display mode.
blurred?
NOTE
Check if the video card's resolution or frequency is within the range allowed by the monitor and set to
yy
the recommended (optimal) resolution in Control Panel > Display > Settings.
Failing to set the video card to the recommended (optimal) resolution may result in blurred text, a
yy
dimmed screen, a truncated display area or misalignment of the display.
The configuration procedure may differ depending on your computer and/or operating system. Also,
yy
some video cards may not support certain resolutions. If this is the case, contact the computer or
video card manufacturer for assistance.
The AUTO option is only available for D-SUB (analog) signals.
yy
The display color is abnormal.
Does the display color appear discolored (16 color)?
Does the display color appear unstable or in monochrome?
Are there spots on the screen?
yy Set the color to 24 bit (true color) or higher. In Windows, go to Control
Panel > Display > Settings > Color Quality.
yy Check if the signal cable is connected properly. Re-connect the cable
or re-insert the PC's video card.
yy When using the monitor, pixilated spots (red, green, blue, white or
black) may appear on the screen. This is normal for the LCD screen.
It is not an error nor is it related to the monitor's performance.
Product Specification
27
PRODUCT SPECIFICATION
Type
Resolution
Pixel Pitch
Maximum Resolution
Video Signal
Input Connector
Power
58.42 cm (23 inch) TFT (Thin Film Transistor)
LCD (Liquid Crystal Display) Screen
Diagonal length of the screen: 58.42 cm
0.2652 mm x 0.2652 mm
1920 x 1080 @ 60 Hz
Recommended Resolution 1920 x 1080 @ 60 Hz
Horizontal Frequency
30 kHz to 68 kHz
Vertical Frequency
57 Hz to 63 Hz
Synchronization
15-pin D-SUB (Analog)
19 V
2.3 A
Separate Sync
Power Consumption:
CLOUD/D-SUB
AC/DC Adapter
Dimension/
Weight
Weight (Without
Packaging)
Stand Angle
Adjustment
Environment
Condition
On Mode: 24 W(D-sub)/29 W(CLOUD)
Power Saving Mode ≤ 0.5 W(CLOUD mode:7 W)
Off Mode ≤ 0.5 W
Type PA-1650-43, manufactured by LITE-ON TECHNOLOGY CORPORATION.
or Type DA-48F19, manuafactured by Asian Power Devices Inc.
OUTPUT: 19 V
2.53 A
Monitor Size (Width x Height x Depth)
With Stand
544.2 mm x 406 mm x 130.6 mm
Without Stand
544.2 mm x 332.3 mm x 47 mm
5.54 kg
Forwards/Backwards: -5° to 15° (Monitor)
Operating Condition
Temperature: 10°C to 35°C; Humidity: 10% to 80%
Storing Condition
Temperature: -20°C to 60°C; Humidity: 5% to 90%
The specifications are subject to change without notice.
ENG
English
LCD Screen
28
Product Specification
Preset Mode
English
ENG
Display Modes
(Resolution)
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
Polarity (H/V)
720 x 400
31.468
70.08
-/+
640 x 480
31.469
59.94
-/-
800 x 600
37.879
60.317
+/+
1024 x 768
48.363
60
-/-
1280 x 1024
63.981
60.02
+/+
1680 x 1050
65.290
59.954
-/+
1920 x 1080
67.5
60
+/+
Power Indicator
Mode
LED Color
On Mode
Red
Power Saving
Blinking Red
Off Mode
Off
Remark
Recommended Mode
Proper Posture
29
PROPER POSTURE
ENG
English
Proper posture for using the monitor
Adjust the angle so that the screen is slightly lower than your eyes.
Using the monitor for a prolonged period of time can cause eye fatigue. Take a 10-minute break every
yy
hour.
The stand is designed to best support the monitor when the optimal conditions are selected.
yy
Adjust the angle of the monitor from -5° to 15° to obtain the best view of the screen.
You should be
looking
slightly down at
the screen.
Adjust the angle
from -5° to 15°
so that there is no reflection
or glare from the
screen.
Place your hands gently
on the keyboard,
keeping your arms bent at
the elbows
and extended horizontally
in front of you.
30
Using CLOUD Solution
Using CLOUD Solution
English
ENG
Note
Menus and functions in CLOUD mode may
yy
be slightly different depending on the firmwareversion.You can download the user
manual for each version from the Teradici
homepage: http://www.teradici.com
To check the firmware version, see page
yy
<47>.
Connect Screen
The Connect screen is shown during start-up,
except when the portal has been configured for a
managed start-up or auto-reconnect. The logo displayed above the Connect button can be changed
by uploading a replacement image via the admin
interface.
<Figure 2-2: Network Not Ready>
If the network is connected and IP is being acquired, the message "Network connection detected. Acquiring IP address …" is displayed on the
Connection screen. Figure 2-3 shows the message
displayed when the network is ready and the IP is
being acquired.
<Figure 2-1: OSD Connect Screen>
<Figure 2-3 Acquiring the IP after Network Connected>
If the network is not properly connected (e.g., during portal boot up), or connection is being created,
the "Network connection lost. Waiting for connection …" message is displayed on the Connection
screen.
Figure 2-2 shows the message displayed when the
network is not ready.
The below is the Connection screen displayed
when network is completely ready.
<Figure 2-4: Network Ready>
Using CLOUD Solution
<Figure 2-5: OSD Connect Screen (Connecting)>
OSD Options Menu
Selecting the Options menu will produce a list of
selections. The OSD Options menu contains:
yy
yy
yy
yy
Configuration
Diagnostics
Information
User Settings
Selecting one of the options will produce a settings
window.
<Figure 2-6: OSD Options Menu>
Configuration Window
In the Configuration window, the administrator can
access the window tabs that contain the settings to
configure and manage the portal environment.
The Configuration window has the following tabs:
yy Network
yy Label
yy Connection Management
yy Discovery
yy Session
yy RDP
yy Language
yy OSD
yy Reset
yy Display
yy VMware View
Each tab contains OK, Cancel and Apply buttons
to allow the administrator to apply or cancel the
modified settings as well as the Advanced button
for advanced settings.
Note
Some PCoIP devices have their password
yy
protection disabled and can be logged into
the management web page or access the
OSD parameters without a password. The
login page and the OSD's password protection can be enabled in the PCoIP management console.
ENG
English
If you select the Connect button, the connection
session is started. When the connection is pending, the "Discovering hosts, please wait…" message is displayed on the OSD local GUI.When the
connection is established, the OSD local GUI will
disappear and be replaced by the session image.
31
32
Using CLOUD Solution
English
ENG
Network Tab
The Network tab allows the administrator to configure the portal network parameters.
NOTE
The network parameters can also be conyy
figured using the Webpage Administration
Interface.
yy Gateway
The Gateway field contains the gateway IP address of the device. If DHCP is disabled, this field
is required. If DHCP is enabled, this field cannot be
edited.
yy Primary DNS Server
The Primary DNS Server field contains the primary
DNS IP address of the device. This field is optional. If DHCP is enabled, this field cannot be edited.
yy Secondary DNS Server
The Secondary DNS Server field contains the secondary DNS IP address of the device. This field is
optional. If the DHCP is enabled, this field cannot
be edited.
yy Domain Name
The Domain Name field contains the domain name
used, e.g. "domain local". This field is optional. It specifies on which domain the host or portal operates.
Figure 2-7. Network Configuration
yy Enable DHCP
If the Enable DHCP option is selected, a device will
be connected to the DHCP server. that allocates
the IP address, subnet mask, gateway IP address,
and DNS server. If this option is disabled, the
above parameters must be configured manually.
yy IP Address
The IP Address field contains the IP address of the
device. If DHCP is disabled, this field is required.
If DHCP is enabled, this field cannot be edited.
This field must contain the correct IP address. If an
incorrect IP address is provided, an OSD message
is displayed prompting the administrator to provide
the correct the IP address.
yy Subnet Mask
The Subnet Mask field contains the subnet mask
of the device. If DHCP is disabled, this field is
required. If DHCP is enabled, this field cannot be
edited. This field must have the correct subnet
mask. If an incorrect subnet mask is provided, an
OSD message is displayed prompting the administrator to provide the correct the subnet mask.
yy FQDN
The FQDN field represents the Fully Qualified Domain Name of the host or portal. The default value is
PCoIP-host-MAC or PCoIP-portal-MAC, where MAC
is the MAC address of the host or portal. If there is
a domain name, it will be added to the FQDN in the
format of PCoIP-host-MAC.domain.local
NOTE
In order to utilize the FQDN feature, a DNS
yy
server, configured properly with DHCP option
81, must be used.
yy Ethernet Mode
The Ethernet Mode field specifies the portal's Ethernet mode.
The available options are as follows.
yy Auto
yy 100 Mbps Full-Duplex
yy 10 Mbps Full-Duplex
If another network device (for example, a switch) is
configured to operate under 10 Mbps Full-Duplex,
100Mbps Full-Duplex or 1GbpsFull-Duplex, the
administrator should always set the Ethernet Mode
field to Auto; and if the device is to operate under
only one speed out of multiple settings, select either 10 Mbps Full-Duplex or 100 Mbps Full-Duplex.
Using CLOUD Solution
yy Secondary DNS Server
The Secondary DNS Server field contains the secondary DNS IP address of the device. This field is
optional. If DHCPv6 is enabled, this field cannot
beedited.
yy Domain Name
The Domain Name field contains the domain name
used, e.g. "domain local". This field is optional. It
specifies on which domain the host or portal operates.
yy FQDN
The FQDN field represents the Fully Qualified Domain Name of the host or portal. The default value
is PCoIP-host-MAC or PCoIP-portal-MAC, where
MAC is the MAC address of the host or portal. If
there is a domain name, it will be added to the
FQDN in the format of PCoIP-host-MAC.domain.
local.
<Figure 2-8: IPv6 Configuration>
yy Enable IPv6
If you select Enable IPv6, the portal in use can be
connected to the network configured with the IPv6.
yy Link Local Address
The Link Local Address field is automatically filled
with the IP address of a device.
yy Gateway
The Gateway field contains the gateway IP address of the device. Enter the gateway address to
be used by a device.
yy Enable DHCPv6
To assign the Dynamic Host Configuration Protocol
version 6 (DHCPv6) of a device select the Enable
DHCPv6 field.
yy DHCPv6 Addresses
When DHCPv6 is enabled and the device restarts,
the server enters the device addresses automatically.
yy Primary DNS Server
The Primary DNS Server field contains the primary DNS IP address of the device. This field is
optional. If DHCPv6 is enabled, this field cannot be
edited.
yy Enable SLAAC
Select the Enable SLAAC field to use the stateless
auto-configuration of the device.
yy Enable Manual Address
Select the Enable Manual Address field to enter
the device address manually.
yy Manual Address
In the Manual Address field, enter the IP address
manually.
ENG
English
<IPv6> Tab
The IPv6 tab is used when the portal is connected
to the network configured with the IP v6.
33
34
Using CLOUD Solution
English
ENG
Label Tab
The Label tab allows the administrator or host to
add customized information to the portal.
NOTE
The portal label parameters can also be conyy
figured using the Webpage Administration
Interface.
Discovery Tab
The Discovery tab allows the administrator to easily find a portal in the PCoIP system.
NOTE
The Discovery parameters can also be conyy
figured using the Webpage Administration
Interface.
<Figure 2-9: Label Configuration>
<Figure 2-9: Label Configuration>
<Figure 2-10: Discovery Configuration>
yy PCoIP Device Name
In the PCoIP Device Name field, the administrator
can specify a logical name to the host or portal.
The default value is PCoIP-host-MAC or PCoIPportal-MAC, where MAC is the MAC address of the
host or portal.
yy PCoIP Device Description
In the PCoIP Device Description field, the administrator can add specific information, such as the endpoint
location, or add a description to the host or portal.
This field cannot be used in the PCoIP firmware and
accessibility is strictly limited to the administrator.
yy Generic Tag
In the Generic Tag field, the administrator can add a
generic tag to the host or portal.
This field cannot be used in the PCoIP firmware and
accessibility is strictly limited to the administrator.
yy Enable Discovery
If the Enable Discovery option is selected, a device
will use SLP Discovery to dynamically locate the
peer device without requiring any information about
the location of the device in the network. This
means that the configuration and maintenance
work in a complicated system can be significantly
reduced.
As SLP Discovery requires a multicast-enabled
router, the recommended search structure is DNSSRV Discovery.
Using CLOUD Solution
See below for information how to set for each option.
ENG
English
Session Tab
The Session tab allows the administrator to set the
method to connect the device to a peer device.
35
NOTE
The Session parameters can also be conyy
figured using the Webpage Administration
Interface.
<Figure 2-12: Direct to Host Setting>
<Figure 2-11: Session Configuration>
yy Connection Type
The Connection Type field allows the user to select
the device to be connected with the portal.
The Connection Type field has following options:
yy Direct to Host
yy Direct to Host + SLP Host Discovery
yy View Connection Server
yy View Connection Server + Auto-Logon
yy View Connection Server + Kiosk
yy View Connection Server + Imprivata OneSign
yy Connection Management Interface
yy Direct to Host
You can view the screen of the host PC by establishing 1:1 connection between the PCI host card
connected to the host PC through the entered IP
address of the host PC and the portal.
yy DNS Name or IP Address
Enter the DNS name or IP address of the host PC.
36
Using CLOUD Solution
English
ENG
yy Direct to Host + SLP Host Discovery
You can view the screen of the host PC by discovering the host PC within the network and establishing 1:1 connection between the PCI host card
connected to the host PC and the portal.
<Figure 2-13: Advanced Settings for Direct to
Host>
yy Enable Auto-Reconnect
If this option is selected, reconnection is attempted
automatically when a session is disconnected or
the user is logged off.
NOTE
This setting is provided only for the client.
yy
yy Enable Peer Loss Overlay
The "Connection Lost" message is displayed.The
display is the same as in the VDI environ-ment.
The default is Disable.
NOTE
yyThis setting is provided only for the client.
yy Enable Preparing Desktop Overlay
If this option is selected, the "Preparing Desk-top"
message is displayed on the screen when the user
is logged in.
yy Disconnect Message Filter
This option determines the type of message to
display when a session is disconnected.
- Show All: Shows all the error messages.
- Show Error and Warning Only: Shows the
error and warning messages only.
- Show Error Only: Shows the error messages
only.
- Show None: Shows nothing.
<Figure 2-14: Direct to Host + SLP Host Discovery Settings>
Using CLOUD Solution
37
<Figure 2-15: Advanced Settings for Direct to Host
+ SLP Host Discovery>
yy Enable Auto-Reconnect
If this option is selected, reconnection is attempted
automatically when a session is disconnected or
the user is logged off.
<Figure 2-16: View Connection Server Setting>
NOTE
This setting is provided only for the client.
yy
yy Enable Peer Loss Overlay
The "Connection Lost" message is displayed.The
display is the same as in the VDI environ-ment.
The default is Disable.
NOTE
yyThis setting is provided only for the client.
yy Enable Preparing Desktop Overlay
If this option is selected, the "Preparing Desk-top"
message is displayed on the screen when the user
is logged in.
yy Disconnect Message Filter
This option determines the type of message to
display when a session is disconnected.
- Show All: Shows all the error messages.
- Show Error and Warning Only: Shows the
error and warning messages only.
- Show Error Only: Shows the error messages
only.
- Show None: Shows nothing.
yy DNS Name or IP Address
Enter the DNS name or IP address of the VMware View Connection Server.
ENG
English
yy View Connection Server
In the Session tab, you can select to enable the
user client to access the VMware View ConnectionServer. To do this, select View Connection
Server for Connection Type.
38
Using CLOUD Solution
English
ENG
yy Prefer GSC-IS
If this option is selected, the GCS-IS interface
is used when a smart card supports more than
one interface. If the smart card supports only one
interface, it is not used.
NOTE
This setting is provided only when a smart
yy
card is used.
<Figure 2-17: Advanced Settings for View Connection Server>
yy Desktop Name to Select
Enter the name of the pool/desktop which the
user client uses upon starting a session.
yy Port
For the default setting, leave the port field empty.
When the VMware View Connection Server uses
the SSL authentication, enter 443 in the Port field.If
the server where a user tries to access uses a port
other than a general port, enter the port.
yy Auto Connect
If this option is enabled, the selected VMware View
Connection Server is automatically connected
when the user client is powered on.
If the Auto Connect option is enabled, you should
turn the user client off and turn it on again at least
once.
yy Remember Username
If this option is selected, the username which is
previously used to access the VMware View
Connection Server is automatically entered in the
username field.
yy Auto Launch if Only One Desktop
If this option is selected, connection is established
to the desktop when there is only one virtual desktop that a user wants to access.
yy Use OSD logo for View banner
If this option is enabled, you can change the OSD
logo of PCoIP during the login.
NOTE
The OSD logo can be uploaded using the
yy
Webpage Administration Interface.
yy Enable Peer Loss Overlay
If this option is selected, the "Network Connection
Lost" message is displayed on the screen when it
is confirmed that the network is disconnected.
The display is the same as in the VDI environment. The default is Disable.
NOTE
yyThis setting is provided only for the client.
yy Enable Preparing Desktop Overlay
If this option is selected, the "Preparing Desktop" message is displayed on the screen when the
user is logged in.
yy Disconnect Message Filter
This option determines the type of message to
display when a session is disconnected.
- Show All: Shows all the error messages.
- Show Error and Warning Only: Shows the
error and warning messages only.
- Show Error Only: Shows the error messages
only.
- Show None: Shows nothing.
Using CLOUD Solution
39
ENG
English
yy View Connection Server with Auto-Logon
In the Session tab, you can select to enable the
user client to automatically access the VMware
View Connection Server.To do this, select View
Connection Server with Auto-Logon for Connection
Type.
<Figure 2-19: Advanced Settings for View Connection Server with Auto-Logon>
<Figure 2-18: View Connection Server with AutoLogon Setting>
yy DNS Name or IP Address
Enter the DNS name or IP address of the VMware View Connection Server.
yy Username
Enter the username for the user client.
yy Password
Enter the password for the user client.
yy Domain
Enter the domain name.
yy Desktop Name to Select
Enter the name of the pool/desktop which the
user client uses upon starting a session.
yy Port
For the default setting, leave the port field empty.
When the VMware View Connection Server uses
the SSL authentication, enter 443 in the Port field.If
the server where a user tries to access uses a port
other than a general port, enter the port.
yy Auto Connect
If this option is enabled, the selected VMware View
Connection Server is automatically connected
when the user client is powered on.
If the Auto Connect option is enabled, you should
turn the user client off and turn it on again at least
once.
yy Remember Username
If this option is selected, the username which is
previously used to access the VMware View
Connection Server is automatically entered in the
username field.
yy Auto Launch if Only One Desktop
If this option is selected, connection is established
to the desktop when there is only one virtual desktop that a user wants to access.
yy Use OSD logo for View banner
If this option is enabled, you can change the OSD
logo of PCoIP during the login.
NOTE
yyThe OSD logo can be uploaded using the
Webpage Administration Interface.
40
Using CLOUD Solution
English
ENG
yy Prefer GSC-IS
If this option is selected, the GSC-IS interface
is used when a smart card supports more than
one interface. If the smart card supports only one
interface, it is not used.
NOTE
This setting is provided only when a smart
yy
card is used.
yy View Connection Server + Kiosk
Select View Connection Server + Kiosk to use
the kiosk mode. You can configure the View Connection Server + Kiosk mode using the Webpage
Administration Interface.
NOTE
You cannot use the kiosk mode by connectyy
ing to the host PC.
yy Enable Peer Loss Overlay
If this option is selected, the "Network Connection
Lost" message is displayed on the screen when it
is confirmed that the network is disconnected.
The display is the same as in the VDI environment. The default is Disable.
NOTE
yyThis setting is provided only for the client.
yy Enable Preparing Desktop Overlay
If this option is selected, the "Preparing Desktop" message is displayed on the screen when the
user is logged in.
yy Disconnect Message Filter
This option determines the type of message to
display when a session is disconnected.
- Show All: Shows all the error messages.
- Show Error and Warning Only: Shows the
error and warning messages only.
- Show Error Only: Shows the error messages
only.
- Show None: Shows nothing.
<Figure 2-20: View Connection Server + Kiosk
Setting>
yy DNS Name or IP Address
Enter the DNS name or IP address of the VMware View Connection Server.
yy Username
Select the type of username that matches the device name used in the VMware View Connection Server.
yy Password
Enter the password for the user client.
Using CLOUD Solution
41
<Figure 2-21: Advanced Setting for View Connection Server + Kiosk>
yy Disconnect Message Filter
This option determines the type of message to
display when a session is disconnected.
- Show All: Shows all the error messages.
- Show Error and Warning Only: Shows the
error and warning messages only.
- Show Error Only: Shows the error messages
only.
- Show None: Shows nothing.
yy View Connection Server + Imprivata OneSign
Connection
Select View Connection Server + Imprivata Onesign Connection to use the Imprivata Onesign Connection for the client authentication.
yy Port
For the default setting, leave the port field empty.
When the VMware View Connection Server uses
the SSL authentication, enter 443 in the Port field.
If the server where a user tries to access uses a
port other than a general port, enter the port.
yy Use OSD logo for View banner
If this option is enabled, you can change the OSD
logo of PCoIP during the login.
NOTE
The OSD logo can be uploaded using the
yy
Webpage Administration Interface.
yy Enable Peer Loss Overlay
If this option is selected, the "Network Connection
Lost" message is displayed on the screen when it
is confirmed that the network is disconnected.
The display is the same as in the VDI environment. The default is Disable.
NOTE
yyThis setting is provided only for the client.
<Figure 2-22: View Connection Server + Imprivata OneSign Connection Setting>
yy Bootstrap URL
Enter the IP address or FQDN information of the
server which performs the OneSign authentication.
ENG
English
yy Enable Preparing Desktop Overlay
If this option is selected, the "Preparing Desktop" message is displayed on the screen when the
user is logged in.
42
Using CLOUD Solution
English
ENG
yy Enable Preparing Desktop Overlay
If this option is selected, the "Preparing Desktop" message is displayed on the screen when the
user is logged in.
<Figure 2-23: Advanced Settings for View Connection Server + Imprivata OneSign Connection>
yy Remember Username
If this option is selected, the username which is
previously used to access the VMware View
Connection Server is automatically entered in the
username field.
yy Use OSD logo for View banner
If this option is enabled, you can change the OSD
logo of PCoIP during the login.
yy Disconnect Message Filter
This option determines the type of message to
display when a session is disconnected.
- Show All: Shows all the error messages.
- Show Error and Warning Only: Shows the
error and warning messages only.
- Show Error Only: Shows the error messages
only.
- Show None: Shows nothing.
yy Connection Management Interface
In the Connection Management Interface setting,
you can manage the connection by entering the IP
address for connection management instead of using the IP address of the VMware View Connection
Server and can select to enable or disabled the
management interface.
NOTE
The OSD logo can be uploaded using the
yy
Webpage Administration Interface.
yy Prefer GSC-IS
If this option is selected, the GCS-IS interface
is used when a smart card supports more than
one interface. If the smart card supports only one
interface, it is not used.
NOTE
This setting is provided only when a smart
yy
card is used.
yy Enable Peer Loss Overlay
If this option is selected, the "Network Connection
Lost" message is displayed on the screen when it
is confirmed that the network is disconnected.
The display is the same as in the VDI environment. The default is Disable.
NOTE
yyThis setting is provided only for the client.
<Figure 2-24: Connection Management Interface
Setting>
yy DNS Name or IP Address
Enter the DNS name or IP address of the VMware
View Connection Server.
Using CLOUD Solution
43
NOTE
The Language parameters can also be conyy
figured using the Webpage Administration
Interface.
<Figure 2-25: Advanced Settings for Connection
Management Interface>
yy Enable Peer Loss Overlay
If this option is selected, the "Network Connection
Lost" message is displayed on the screen when it
is confirmed that the network is disconnected.
The display is the same as in the VDI environment. The default is Disable.
NOTE
yyThis setting is provided only for the client.
yy Enable Preparing Desktop Overlay
If this option is selected, the "Preparing Desktop" message is displayed on the screen when the
user is logged in.
yy Enable Event Log Notification
With this option, you can select whether to allow
the host and client device to send their event log
information to the Connection Management Server.
yy Disconnect Message Filter
This option determines the type of message to
display when a session is disconnected.
- Show All: Shows all the error messages.
- Show Error and Warning Only: Shows the
error and warning messages only.
- Show Error Only: Shows the error messages
only.
- Show None: Shows nothing.
<Figure 2-26: Language Configuration>
yy Language
The Language field is used to set the display
language of the OSD and the user level event log
messages.
yy Keyboard Layout
The Keyboard Layout field allows the administrator
to modify the keyboard layout.
ENG
English
Language Tab
The Language tab allows the administrator to set
the OSD language.
44
Using CLOUD Solution
English
ENG
OSD Tab
The OSD tab allows the administrator to modify the
On Screen Display (OSD) parameters.
NOTE
The OSD parameters can also be configured
yy
using the Webpage Administration Interface.
<Figure 2-27: OSD Configuration>
yy Screen-Saver Timeout
The Screen-Saver Timeout field allows the administrator to set a time limit for the screen saver.
The time limit is defined in seconds. The maximum
time is 9999 seconds. If it is set to 0 seconds, the
screen saver will be turned off.
Display Tab
The Display tab allows the user to configure the
EDID function of the monitor.
NOTE
The Enable display override function can be
yy
used when the EDID function of the monitor
is not running.
<Figure 2-28: Display Configuration>
Using CLOUD Solution
NOTE
The Reset function can also be accessed
yy
through the Webpage Administration Interface.
Diagnostics Window
In the Diagnostics window, the administrator can
access the window tab to diagnose the portal. The
Diagnostics window has the following tabs:
yy Event Log
yy Session Statistics
yy PCoIP Processor
yy Ping
Each tab has the Close button to close the window.
Event Log Tab
The Event Log tab allows the administrator to view
and delete the event log messages from the portal.
NOTE
The event log (regardless of the quantity)
yy
can also be reset using the Webpage Administration Interface.
<Figure 2-29: Reset>
yy Reset Parameters
Pressing the Reset Parameters button will reset all
settings and options to the factory default settings.
When this button is pressed, an OSD message is
displayed. This is to prompt the administrator and
prevent accidental reset.
<Figure 2-30: Event Log>
yy View Event Log Message
The View Event Log Message field displays the log
messages accompanied by the timestamp information. The following two buttons are available:
yy Refresh
The Refresh button refreshes the displayed event
log messages.
yy Clear
The Clear button clears all event log messages.
ENG
English
Reset Tab
The Reset tab allows the administrator to reset all
configurable parameters stored in Flash.
45
46
Using CLOUD Solution
English
ENG
Session Statistics Tab
The Session Statistics tab allows the administrator
to view the PCoIP specific statistics of the last active PCoIP session from the portal.
PCoIP Processor Tab
The PCoIP Processor tab allows the administrator
to view the portal PCoIP processor's uptime since
its last booting.
NOTE
The session statistics (regardless of the
yy
quantity) can also be viewed using the Webpage Administration Interface.
NOTE
The PCoIP Processor Uptime can also be
yy
viewed using the Webpage Administration
Interface.
<Figure 2-31: Session Statistics>
yy PCoIP Packets Statistics
yy PCoIP Packets Sent
The PCoIP Packets Sent field shows the total
number of PCoIP packets sent from the portal
to the host in the last active session.
yy PCoIP Packets Received
The PCoIP Packets Received field shows the
total number of PCoIP packets received from
the host to the portal in the last active session.
yy PCoIP Packets Lost
The PCoIP Packets Lost field shows the total
number of PCoIP packets lost in the last active session.
yy Bytes Statistics
yy Bytes Sent
The Bytes Sent field shows the total number
of bytes sent in the last active session.
yy Bytes Received
The Bytes Received field shows the total
number of bytes received in the last active
session.
yy Round Trip Latency
The Round Trip Latency field shows the total
round-trip PCoIP system (e.g. from the portal to
the host, then back to the portal) and the network
latency in milliseconds (+/- 1 ms).
<Figure 2-32: PCoIP Processor>
Using CLOUD Solution
47
ENG
English
Ping Tab
The Ping tab allows the administrator to perform a
ping test to the device and check if it can reach the
overall IP network. This is useful to check whether
the device can reach the host.
NOTE
The Ping tab has no corresponding menu in
yy
to the Webpage Administration Interface of
Section 1.
<Figure 2-34: Version>
<Figure 2-33: Ping>
yy Ping Settings
yy Destination
The IP address or FQDN to perform the ping
test.
yy Interval
The interval between the ping packets.
yy Packet Size
The size of the ping packet.
yy Packets
yy Sent
The number of ping packets sent.
yy Received
The number of ping packets received.
Information Window
In the Information window, the administrator can
access the Version tab that contains the device
related information.
NOTE
The version information can also be viewed
yy
using the Webpage Administration Interface.
yy VPD Information
The Vital Product Data (VPD) is information that
uniquely identifies each portal or host.
yy MAC Address
The portal MAC address
yy Unique Identifier
The portal ID
yy Serial Number
The portal serial number
yy Firmware Part Number
The part number of the PCoIP firmware
yy Hardware Version
The portal hardware version
yy Firmware Information
The Firmware Information shows the details of the
current PCoIP firmware.
yy Firmware Version
The current PCoIP firmware version
yy Firmware Build ID
The current PCoIP firmware revision code
yy Firmware Build Date
The current PCoIP firmware build date
PCoIP Processor Revision
This shows the PCoIP processor's revision code.
TERA1x00 Revision A silicone is denoted by 0.0
and TERA1x00 Revision B silicone is denoted by
1.0.
yy Boot Loader Information
The Boot Loader Information shows the details of
the current PCoIP boot loader.
yy Boot Loader Version
The current PCoIP boot loader version
yy Boot Loader Build ID
The current PCoIP boot loader revision code
yy Boot Loader Build Date
The current PCoIP boot loader build date
48
Using CLOUD Solution
English
ENG
User Settings Window
In the User Settings window, the administrator can
access the tab to select the mouse and keyboard
and define the PCoIP image quality.
The User Settings window has the following tabs:
yy VMware View
yy Mouse
yy Keyboard
yy Image
yy Display Topology
yy Touch Screen
yy VMware View Tab
The VMware View tab allows user to specify the
client behavior for when a user cannot check the
secure connection to a server.
<Figure 2-35: VMware View>
yy Reject the unverifiable connection (Secure)
Connection can be established only when the certificate is verified and otherwise it cannot.
yy Warn if the connection may be insecure (Default)
The authentication status is checked and a warning message is displayed, if required. However,
there is no connection limit.
yy Allow the unverifiable connection (Not Secure)
No authentication is required and no connec-tion
limit exists.
Mouse Tab
The Mouse tab allows the user to modify the OSD
and RDP session's mouse cursor speed setting.
NOTE
The OSD mouse cursor speed setting does
yy
not affect the mouse cursor settings when
a PColP session is active unless the Local
Keyboard Host Driver function is being used
(see PColP Host Software User Guide for
more information).
The Mouse tab has no corresponding menu
yy
in the Webpage Administration Interface of
Section 1.
<Figure 2-36: Mouse>
yy Mouse Speed
The Mouse Speed field allows the user to set the
portal's mouse cursor speed.
NOTE
The Mouse Speed can also be configured via
yy
the PCoIP Host Software. For more information on using the PCoIP Host Software, refer
to the PCoIP Host Software User Guide.
Using CLOUD Solution
NOTE
The OSD keyboard setting does not affect
yy
the keyboard settings when a PColP session
is active unless the Local Keyboard Host
Driver function is being used (see PColP
Host Software User Guide for more information).
The Keyboard tab has no corresponding
yy
menu in the Webpage Administration Interface of Section 1.
Image
The Image tab allows a user to change the image
settings on the PCoIP system.
NOTE
The Image parameters can also be conyy
figured using the Webpage Administration
Interface.
<Figure 2-38: Image>
<Figure 2-37: Keyboard>
yy Keyboard Repeat Delay
The Keyboard Repeat Delay field allows the user
to set the portal's keyboard repeat delay.
yy Keyboard Repeat Rate
The Keyboard Repeat Rate field allows the user to
set the portal's keyboard repeat rate.
yy Repeat Settings Test Box
The Repeat Settings Test Box allows the user to
test the selected keyboard settings.
yy Minimum Image Quality
The Minimum Image Quality slider allows the administrator to make compromises between image
quality and frame rate when network bandwidth
is limited. Sometimes, lower-quality images at a
higher frame rate may be required, while at other
times, higher-quality images at a lower frame rate
may be preferred.
In environments where the network bandwidth is
limited, moving the slider towards Reduced ensures higher frame rates;
moving the slider towards Perception-Free ensures
higher image quality. When network bandwidth is
not limited, the PCoIP system will maintain perception-free quality regardless of the Minimum Image
Quality setting.
ENG
English
Keyboard Tab
The Keyboard tab allows the user to modify the
OSD and RDP session's keyboard repeat setting.
49
50
Using CLOUD Solution
English
ENG
yy Display Topology Tab
The Display Topology tab allows the user to specify
the position and alignment of a connected secondary monitor.
yy Touch Screen Tab
The Touch Screen tab allows the user to specify
the touch sensitivity and alignment when the monitor supports the touch screen function.
NOTE
yyIt is applicable when the VMware View Connection Server version is 4.5 or later.
<Figure 2-40: Touch Screen>
<Figure 2-39: Display Topology>
yy Enable Configuration
When this option is selected, you can set the
display position and alignment. You can save the
settings by clicking the Apply or OK button, and
the settings will be reset if you initialize the monitor
set.
yy Display Layout
This option allows the user to specify the direction
of monitor connection: vertical or horizontal.
yy Alignment
This option allows the user to specify the alignment position of the monitor to be connected when
there is a resolution difference between the two
monitors.
yy Primary
This option allows the user to change the primary/
secondary settings of the connected monitor.
yy Enable right click on hold
If this option is selected, clicking and holding the
touch screen for several seconds works the same
as the mouse right click.
yy Right Click Delay
This option allows the user to make moving the
pointer position work the same as the mouse right
click. You can also specify the distance to move
(from Long to Short).
yy Touch screen calibration
The alignment of a touch screen is started when
clicking the Start button.
Declaration of Conformity
Trade Name: LG
Model : 23CAV42KL
Responsible Party: LG Electronics Inc.
Address : 1000 Sylvan Ave. Englewood Cliffs
NJ 07632 U.S.A
TEL: 201-266-2534
*above information is only for USA FCC Regulatory
Make sure to read the Safety Precautions before
using the product.
Keep the Owner’s Manual (CD) in an accessible
place for future reference.
The model and serial number of the SET is
located on the back and one side of the SET.
Record it below should you ever need service.
MODEL
SERIAL
To obtain the source code under GPL, LGPL,
MPL and other open source licenses, that is
contained in this product, please visit http://
opensource.lge.com .
In addition to the source code, all referred
license terms, warranty disclaimers and
copyright notices are available for download.
LG Electronics will also provide open source
code to you on CD-ROM for a charge covering
the cost of performing such distribution (such
as the cost of media, shipping and handling)
upon email request to opensource@lge.com.
This offer is valid for three (3) years from the
date on which you purchased the product.
Download PDF