LG | 47VL10 | LG 47VL10 Owner’s Manual

ENG
ENGLISH
OWNER’S MANUAL
MONITOR SIGNAGE
Please read this manual carefully before operating the
your set and retain it for future reference.
MONITOR SIGNAGE MODEL
47VL10
www.lg.com
2
TABLE OF CONTENTS
ENGLISH
ENG
CONTENTS
3
LICENSES
26 MAKING CONNECTIONS
27
4
ASSEMBLING AND
PREPARING
4
Accessories
5
Optional Accessories
6
Parts and buttons
7
Connecting the stand
7
Connecting the Speakers
8
Cable Management
9
Connecting stand hole cover
9
To install Portrait
10
Installing on a wall
11
REMOTE CONTROL
Connecting to a HD receiver, DVD,
Camcorder, Camera, Gaming Device or
VCR player
27
- HDMI connection
27
- HDMI/DVI connection
28
- AV(CVBS) connection
29 TROUBLESHOOTING
32 SPECIFICATIONS
35 RS-232C
35
Connecting the cable
35
RS-232C Configurations
12 USING THE MONITOR SET
35
Communication Parameter
36
Command reference list
12
Connecting to a PC
38
Transmission / Receiving protocol
12
- Using the input list
47
IR CODES
13
- RGB connection
13
- HDMI/DVI connection
14
- HDMI connection
14
- LAN connection
15 CUSTOMIZING SETTINGS
15
Accessing main menus
16
- PICTURE settings
20
- AUDIO settings
21
- TIME settings
22
- OPTION settings
25
- INFORMATION settings
LICENSES
3
Supported licenses may differ by model. For more information of the licenses, visit www.lg.com.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks
or registered trademarks of HDMI Licensing LLC.
ENG
ENGLISH
LICENSES
4
ASSEMBLING AND PREPARING
ENGLISH
ENG
ASSEMBLING AND PREPARING
Accessories
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual product
and accessories.
Remote control and Batteries
Power Cord
User Manual/Card
15-pin D-SUB Signal Cable
CAUTION
Do not use any pirated items to ensure the safety and product life span.
yy
Any damages or injuries by using pirated items are not covered by the warranty.
yy
NOTE
The accessories supplied with your product may vary depending on the model.
yy
Product specifications or contents in this manual may be changed without prior notice due to upgrade
yy
of product functions.
ASSEMBLING AND PREPARING
5
Optional Accessories
Stand
Screws
Speaker
Screws/Cable
Cable holder/
Cable Tie
cable management
Stand kit
Speaker kit
Stand hole cover
Screws
Stand hole cover
kit
NOTE
Cable holder/Cable tie may not be available in some areas or for some models.
yy
Optional accessories are not included for all models.
yy
ENG
ENGLISH
Without prior notice, optional accessories are subject to change to improve the performance of the product,
and new accessories may be added. The illustrations in this manual may differ from the actual product and
accessories.
6
ASSEMBLING AND PREPARING
Parts and buttons
ENGLISH
ENG
Screen Buttons
Screen Marks
Connection panel
Screen Marks
Description
INPUT
Changes the input source.
MENU
Accesses the main menus, or saves your input and exits the menus.
▼▲
Adjust the up and down.
◄►
Adjusts the volume level.
AUTO/SET
For optimal screen display, automatically adjusts screen resolution.
Turns the power on or off.
/I
IR Receiver
This is where the unit receives signals from the remote control.
Power Indicator
This Indicator lights up blue when the display operates normally(on mode). If the display
is in sleep (Energy Saving) mode, this indicator color changes to amber.
NOTE
You can set the Power indicator to on or off by selecting OPTION in the main menus.
yy
ASSEMBLING AND PREPARING
Connecting the Speakers
- Only on some models.
- Only on some models.
1 Take the parts for the stand out of the box and
1 Mount the product onto the speaker by using
assemble them as shown in the picture.
Stand
a screw as shown in the following connect the
speaker cable.
Screws
cable management
2 Place a soft cloth on the table and put the
product with the screen facing downward.
Connect the stand as shown in the following
picture.
2 After installing your speakers, use holders and
cable ties to organize the speaker cables. (This
feature is not available in all model.)
3 Use the screws to secure the stand on the rear
side of the product as shown in the diagram.
NOTE
Connect the speaker terminals noting the
yy
correct polarity.
ENG
ENGLISH
Connecting the stand
7
8
ASSEMBLING AND PREPARING
Cable Management
ENGLISH
ENG
- Only on some models.
1 Arrange the cables in the center as shown in
the following picture.
Using the Kensington security system
The Kensington security system connector is
located at the back of the Monitor set. For more
information of installation and using, refer to the
manual supplied with the Kensington security
system or visit http://www.kensington.com .
Connect the Kensington security system cable
between the Monitor set and a table.
2 Fit the cable management to the back to help
manage the cables.
NOTE
3 For removing the cable management, hold the
Cable management with both hands and pull it
downward.
NOTE
Do not use the cable management as a
yy
handle for the Monitor.
The illustrations in this manual may differ
yy
from actual cable interfaces.
The Kensington security system is optional.
yy
You can obtain additional accessories from
most electronics stores.
ASSEMBLING AND PREPARING
To install Portrait
- Only on some models.
- Only on some models.
1 Take the parts for the stand out of the box and
assemble them as shown in the picture.
Stand hole cover
When installing Portrait, rotate it clockwise based
on its front.
Screws
2 Place a soft cloth on the table and put the
product with the screen facing downward.
Connect the stand hole cover as shown in the
following picture. NOTE
When using the wall mounting bracket or
yy
the portrait scene mode, the opening can be
covered by the stand hole cover.
3 Use the screws to secure the stand hole cover
on the rear side of the product as shown in the
diagram.
ENG
ENGLISH
Connecting stand hole cover
9
10
ASSEMBLING AND PREPARING
Installing on a wall
CAUTION
ENGLISH
ENG
Install the monitor at least 10 cm away from the
wall and leave about 10 cm of space at each side
of the monitor to ensure sufficient ventilation. Detailed installation instructions can be obtained from
your local retail store. Please refer to the manual
to install and set up a tilting wall mounting bracket.
Disconnect the power cord first, and then
yy
move or install the Monitor set. Otherwise
electric shock may occur.
If you install the Monitor set on a ceiling or
yy
slanted wall, it may fall and result in severe
injury. Use an authorized LG wall mount
and contact the local dealer or qualified
personnel.
Do not over tighten the screws as this may
yy
cause damage to the Monitor set and void
your warranty.
Use the screws and wall mounts that
yy
meet the VESA standard. Any damages
or injuries by misuse or using an improper
accessory are not covered by the warranty.
10 cm
10 cm
10 cm
10 cm
If you want to mount the monitor on the wall (optional), attach the wall mounting bracket to the rear
of the monitor.
Make sure that the wall mounting bracket is securely fixed to the monitor and to the wall.
Use the wall mount plate and screws that comply
with the VESA standard as specified below.
785mm(31 inch) or greater
yy
* Fastening screw: Diameter 6.0 mm x Pitch 1.0
mm x Length 10 mm
(32 inch is Diameter 4.0 mm x Pitch 0.7 mm x
Length 10 mm)
NOTE
Use the screws that are listed on the VESA
yy
standard screw specifications.
The wall mount kit includes an installation
yy
manual and necessary parts.
The wall mount bracket is optional. You can
yy
obtain additional accessories from your local
dealer.
The length of screws may differ depending
yy
on the wall mount. Be sure to use the proper
length.
For more information, refer to the
yy
instructions supplied with the wall mount.
REMOTE CONTROL
11
The descriptions in this manual are based on the buttons of the remote
control. Please read this manual carefully and use the Monitor set correctly.
To replace batteries, open the battery cover, replace batteries (1.5 V AAA)
matching
and
ends to the label inside the compartment, and close the
battery cover. To remove the batteries, perform the installation actions in
reverse.
CAUTION
Do not mix old and new batteries, as this may damage the remote control.
yy
Make sure to point the remote control to the remote control sensor on the Monitor set.
(POWER)
Turns the Monitor set on or off.
AV
Toggles through video.
AV -> RGB PC -> HDMI/DVI
Sleep
When watching AV, RGB
PC,HDMI/DVI.The product will
be automatically turned off after
a certain period of time.
Press this button repetitively
to select an appropriate time
duration.
PSM
Toggles through preset video
settings.
Menu
UP and Down
Bring up and down direction adjustment.
Mute
INPUT
Selects the input mode.
ARC
Aspect Ratio Correction.
Toggles through aspect ratio
options.
Auto
Automatic adjustment function
(Operational for the analog
signal only)
There is not a function
which is supported
Exit
Volume ◄ ►
Volume up and down.
Check
There is not a function
which is supported.
ENG
ENGLISH
REMOTE CONTROL
12
USING THE MONITOR SET
ENGLISH
ENG
USING THE MONITOR SET
Connecting to a PC
Your Monitor set supports the Plug & Play* feature .
* Plug & Play: The function when a PC recognizes
a connected device that users connect to a PC
and turn on, without device configuration or user
intervention.
Using the input list
Selecting an input source
1 Press INPUT to access the input source list.
-The connected device displays on each input
source.
2 Press the Navigation buttons to scroll to one of
the input sources and press OK.
Input source
NOTE
It is recommended to use the Monitor set
yy
with the HDMI connection for the best image
quality.
Use a shielded signal interface cable, such
yy
as D-sub 15 pin signal cable and DVI/
HDMI cable, with a ferrite core to maintain
standard compliance for the product.
If you turn the Monitor set on when the set
yy
becomes cold, the screen may flicker. This
is normal.
Some red, green, or blue spots may appear
yy
on the screen. This is normal.
CAUTION
Connect the signal
yy
input cable and tighten
it by turning the screws
clockwise.
Do not press the screen with your finger for
yy
a long time as this may result in temporary
distortion on the screen.
Avoid displaying a fixed image on the
yy
screen for a long period of time to prevent
image burn. Use a screensaver if possible.
Description
AV
Watch the contents in a VCR or
other external devices
RGB-PC
View a PC display on the screen
HDMI/DVI
Watch contents in a PC, DVD
or Digital settop box other high
definition devices
USING THE MONITOR SET
13
HDMI/DVI connection
Transmits the analog video signal from your PC to
the Monitor set. Connect the PC and the Monitor
set with the D-sub 15 pin cable as shown the
following illustrations.
Select RGB input source.
Transmits the digital video signal from your PC to
the Monitor set. Connect the PC and the Monitor
set with the HDMI/DVI cable as shown the
following illustrations.
Select HDMI/DVI input source.
PC/MAC
PC
PC
(not included)
ENG
ENGLISH
RGB connection
PC
(not included)
(not included)
Macintosh Adapter
(not included)
HD
HDM
Back of the Monitor Set
NOTE
Use the standard
yy
Macintosh adapter
since an incompatible
adapter is available in
the market. (Different
signaling system)
Back of the Monitor Set
NOTE
When HDMI PC is used, a compatiblity
yy
problem might occur.
14
USING THE MONITOR SET
ENGLISH
ENG
HDMI connection
LAN connection
Transmits the digital video and audio signals from
your PC to the Monitor set. Connect the PC and
the Monitor set with the HDMI cable as shown in
the following illustrations.
Select HDMI/DVI input source.
Connect the LAN cable and install the eZ-Net
Manager program on the CD-ROM.
For more information about the program, please
refer to eZ-Net Guide in the enclosed CD-ROM.
A Connect PC to Monitor directly.
PC
LAN
Monitor Set
PC
(not included)
B Using a router(Switch)
LAN
Switch
Monitor Set
PC
HDMI/DVI IN
Back of the Monitor Set
C Using the Internet.
Network
Network
LAN
NOTE
Use a High Speed HDMI™ Cable.
yy
Please check the PC environment if you
yy
cannot hear the sound in HDMI mode.
If you want to use HDMI-PC mode, you must
yy
set the input label to PC mode.
Monitor Set
Network
PC
NOTE
Using LAN establishes communication
yy
between your PC and the monitor and
enables to use the OSD menus on the PC as
well as on the monitor.
CUSTOMIZING SETTINGS
ENG
ENGLISH
CUSTOMIZING SETTINGS
Accessing main menus
1 Press MENU to access the main menus.
2 Press the Navigation buttons to scroll to one of the following menus and press SET.
3 Press the Navigation buttons to scroll to the setting or option you want and press SET.
4 When you are finished, press EXIT.
PICTURE ( See p.16 )
Adjusts the image size, quality, or
effect
AUDIO ( See p.20 )
Adjusts the sound quality, effect, or
volume level
TIME ( See p.21 )
Sets the time, date or Timer feature
OPTION ( See p.22 )
Customizes the general settings
INFORMATION ( See p.25 )
Adjust Set ID and check Serial No.
and SW version.
15
16
CUSTOMIZING SETTINGS
PICTURE settings
Picture
ENGLISH
ENG
1 Press MENU to access the main menus.
2 Press the Navigation buttons to scroll to PICTURE and
press SET.
3 Press the Navigation buttons to scroll to the setting or
Picture Mode
Color Temperature
Advanced
Aspect Ratio
Picture Reset
Screen
option you want and press SET.
-To return to the previous level, press .
4 When you are finished, press EXIT.
MENU
The available picture settings are described in the following:
Setting
Picture Mode
Description
Selects one of the preset image or customizes options in each mode for the best Monitor set screen
performance. You are also able to customize advanced options of each mode.
The available preset picture modes vary depending on the Monitor set .
Mode
Vivid
Adjusts the video image for the retail environment by enhancing the contrast,
brightness, Colour, and sharpness.
Standard
Adjusts the image for the normal environment.
Cinema
Optimizes the video image for a cinematic look to enjoy movies as if you are
in a movie theater.
Sport
Optimizes the video image for high and dynamic actions by emphasizing
primary Colours such as white, grass, or sky blue.
Game
Optimizes the video image for a fast gaming screen such as PCs or games.
User 1,2
Adjusts the detailed video image settings for video experts as well as general
viewers.
Backlight
djusts the brightness of the screen by controlling the LCD backlight. If you
A
decrease the brightness level, the screen becomes darker and the power
consumption will be reduced without any video signal loss.
Contrast
Increases or decreases the gradient of the video signal. You may use
Contrast when the bright part of the picture is saturated.
Brightness
Adjusts the base level of the signal in the picture. You may use Brightness
when the dark part of the picture is saturated.
Color
Adjusts intensity of all Colors.
Sharpness
Adjusts the level of clearness of the picture. The lower the level, the softer the
image.
Tint
Adjusts the balance between red and green levels.
Expert
To compensate for each image mode, or adjust image values according to
a particular image. (Applied only to User2 menu.) (Function works in the
following mode - AV, HDMI-DTV)
NOTE
If the 'Picture Mode' setting in the Picture menu is set to Vivid, Standard,
yy
Cinema, Sport or Game the subsequent menus will be automatically set.
You cannot adjust colour and tint in the RGB-PC / HDMI-PC mode.
yy
When the User 1,2 is selected, you can select Backlight, Contrast,
yy
Brightness, Color, Sharpness, Tint or Expert.
CUSTOMIZING SETTINGS
Setting
Advanced
Description
Color Settings
Option
Cool
Sets the screen color to a bluish tone.
Medium
Sets the screen to the standard color.
Warm
Sets the screen color to a reddish tone.
User
Select this option to use the user-defined settings.
Gamma
(Low/Medium/High)
You can adjust brightness of dark area and middle gray level area of the
picture.
»» Low: Make dark and middle gray level area of the picture brighter.
»» Medium: Express original picture levels.
»» High: Make dark and middle gray level area of the picture darker.
Film Mode
(On/Off)
You can watch a cinema-like video by eliminating judder effect.
Use this function when you watch movies.
Black Level
(Low/High)
»» Low: The picture of the screen gets darker.
»» High: The picture of the screen gets brighter.
Set black level of the screen to proper level.
This function enables to select 'Low' or 'High' in the following mode: AV, HDMIDTV.
* This is available in AV,HDMI-DTV.
NR
(Off/Low/High/
Adaptive)
Reduces screen noise without compromising video quality.
Aspect Ratio
Changes the image size to view images at its optimal size.
Picture Reset
Return Picture Mode, Color Temperature, Advanced, Aspect Ratio to the default factory settings.
SCREEN
(In RGB)
Customizes the PC display options in RGB mode.
Option
Auto Config. (RGB
PC input only)
This button is for the automatic adjustment of the screen position, clock and
phase. This function is available for analog signals only.
* Phase, Clock function are not available in HDMI/DVI DTV.
Manual Config.
If the picture isn't clear after auto adjustment and characters are still
trembling, adjust the picture phase manually.
* Phase, Clock function are not available in HDMI/DVI DTV.
Phase : To adjust the focus of the display. This item allows you to remove any
horizontal noise and clear or sharpen the image of characters. This
function is available for analog signals only.
Clock : To minimize any vertical bars or stripes visible on the screen
background. The horizontal screen size will also change. This function
is available for analog signals only.
H-Position : Moving the screen position horizontally.
V-Position : Moving the screen position vertically.
H-Size : Adjust the horizontal size of the screen.
V-Size : Adjust the vertical size of the screen.
XGA Mode (RGB-PC For more improved or better picture quality, select the same mode
only)
corresponding to computer resolution.
Reset
Return Manual config. and XGA Mode to the default factory settings.
ENG
ENGLISH
Color
Temperature
17
18
CUSTOMIZING SETTINGS
Aspect Ratio
ENGLISH
ENG
Resize the image to view the image at its optimal
size by pressing ARC button while you are
watching Monitor set.
- Original : The aspect ratio is not adjusted from
the original. It is set by the program being
watched.
CAUTION
If a fixed image displays on the screen for a
yy
long period of time, it will be imprinted and
become a permanent disfigurement on the
screen. This is “image burn” or “burn-in” and
not covered by the warranty.
If the aspect ratio is set to 4:3 for a long
yy
period of time, image burn may occur on
the letterboxed area of the screen.
NOTE
Original
- 4:3 : The following selection will allow you to
view a picture with an original 4:3 aspect ratio,
gray bars will appear on both the left and right of
the screen.
You can also change the image size by
yy
accessing the main menus.
- 16:9 : The following selection will allow you
to adjust the picture horizontally, in linear
proportion, to fill the entire screen(useful for
viewing 4:3 formatted DVDs).
- 1:1 : The aspect ratio is not adjusted from the
original. (Only HDMI/DVI PC, RGB PC)
- Just Scan: Following Selection will lead to you
view the picture of best quality without loss of
original picture in high resolution image.
* Note: If there is noise in original Picture, You can
see the noise at the edge.
Just Scan
CUSTOMIZING SETTINGS
- Zoom 1,2 : The following selection will allow you
to view the picture without any alteration, while
filling the entire screen. However, the top and
bottom of the picture will be cropped.
MODE
AV
ARC
HDMI/DVI
RGB
DTV
PC
PC
16:9
o
o
o
o
Just Scan
x
o
x
x
Original
o
x
x
x
4:3
o
o
o
o
1:1
x
x
o
o
14:9
o
x
x
x
Zoom 1
o
x
x
x
Zoom 2
o
x
x
x
ENG
ENGLISH
14:9 : You can view a picture format of 14:9 or a
general Monitor set programme in the 14:9 mode.
The 14:9 screen is viewed in the same way as in
4:3, but is magnified to the left and right.
19
20
CUSTOMIZING SETTINGS
AUDIO settings
AUDIO
ENGLISH
ENG
1 Press MENU to access the main menus.
2 Press the Navigation buttons to scroll to AUDIO and press
SET.
Sound Mode
Auto Volume
Balance Speaker
3 Press the Navigation buttons to scroll to the setting or
option you want and press SET.
-To return to the previous level, press .
4 When you are finished, press EXIT.
MENU
The available audio options are described in the following:
Setting
Sound Mode
Description
Selects one of the preset sound modes or customize each option in each mode.
Mode
Clear Voice
By differentiating the human sound range from others,it helps users listen to
human voices better.
Standard
Select when you want standard-quality sound.
Music
Select when you listen to music.
Cinema
Select when you watch movies.
Sport
Select when you watch sports events.
Game
Select when you play games.
User
Select this option to use the user-defined audio settings.
NOTE
If sound quality or volume is not at the level you want, it is recommended to
yy
use a separate home theater system or amplifier to cope with different user
environments.
Auto Volume
Activates the Auto Volume feature to keep the volume level consistent whenever you change
programmes.
Balance
Adjusts balance between the left and right speakers according to your room environment.
Speaker
ON: Enables sound to the monitor speaker. (* The monitor speaker is sold separately.)
OFF: Disables sound to the monitor speaker. Use this option when using an external sound device.
CUSTOMIZING SETTINGS
TIME settings
TIME
2 Press the Navigation buttons to scroll to TIME and press
SET.
3 Press the Navigation buttons to scroll to the setting or option
Sleep Timer
Auto Sleep
Power On Delay
Power Saving
Automatic Standby
you want and press SET.
-To return to the previous level, press .
4 When you are finished, press EXIT.
MENU
The available time settings are described in the following:
Description
Sleep Timer
Sets the length of time until the Monitor set to turns off. When you turn the Monitor set off and
turn it on again, the Sleep Timer will be set to off.
Auto Sleep
If Auto Sleep is active and there is no input signal, the set switches to off mode automatically
after 10 minutes.
Power On Delay
When connecting multiple monitors and turning the power on, the monitors are turned on
individually to prevent overload.
Power Saving
This screen brightness adjusting menu helps you save energy.
Level: Total 4 screen brightness levels are provided.
- Off: 100% light - Level 1: 80% light
- Level 2: 60 % light - Level 3: 40% light
Automatic
Standby
If you do not use the monitor for more than 4 hours, it will be in standby mode automatically.
NOTE
The Automatic Standby function may not be available depending on the country.
yy
ENG
ENGLISH
1 Press MENU to access the main menus.
Setting
21
22
CUSTOMIZING SETTINGS
OPTION settings
OPTION
ENGLISH
ENG
1 Press MENU to access the main menus.
2 Press the Navigation buttons to scroll to OPTION and press
SET.
3 Press the Navigation buttons to scroll to the setting or
option you want and press SET.
-To return to the previous level, press .
Language
Key Lock
ISM Method
Power Indicator
DPM Select
Tile Mode
Network Setup
Factory Reset
4 When you are finished, press EXIT.
MENU
The available option settings are described in the following:
Setting
Description
Language
To choose the language in which the control names are displayed.
Key Lock
Use the buttons to select On or Off. The monitor can be set up so that it can only be used with
the remote control. This feature can prevent unauthorized viewing.
In order to lock the OSD screen adjustment, set the Key Lock tab to the 'On' position.
In order to unlock it, do the following :
Push the MENU button on the remote control and set Key Lock to the 'Off' position.
ISM Method
A frozen or still picture from a PC/Video game displayed on the screen for prolonged periods
could result in a ghost image remaining even when you change the image. Avoid allowing a
fixed image to remain on the screen for a long period of time.
Mode
Normal
Leave on normal if you don't foresee image burn in being a problem.
White wash
White wash fills the screen with solid white. This helps removes permanent
images burned into the screen. A permanent image may be impossible to
clear entirely with white wash.
Orbiter
May help prevent ghost images. However, it is best not to allow any fixed
image to remain on the screen. To avoid a permanent image on the screen,
the screen will move every 2 minutes.
Inversion
This function inverts the panel color of the screen. The panel color is
automatically inverted every 30 minutes.
Dot Wash
his function moves the black dots of the screen. The black dots is
T
automatically moved every 5 second.
Power Indicator
Use this function to set the power indicator on the front side of the product to On or Off.
DPM Select
A user can choose to turn the power saving mode on / off.
CUSTOMIZING SETTINGS
Setting
Description
To use this function
- Must be displayed with various other products.
- Must be in a function that can be connected to RGB Cable by distributor and RS-232C.
Tile mode and choose Tile alignment and set the ID of the current product to set location.
* Only after pressing the SET button the adjustments made to the settings will be saved.
- Tile mode : column x row ( c = 1, 2, 3, 4,5 r = 1, 2, 3, 4,5)
- 5 x 5 available.
- Configuration of an integration screen is available as well as configuration of One by one
Display.
Mode
H-Size
Adjust the horizontal size of the screen taking into account the size of the
bezel.
V-Size
Adjust the vertical size of the screen taking into account the size of the bezel.
H-Position
Moving the screen position horizontally.
V-Position
Moving the screen position vertically.
Reset
unction to initialize and release Tile.
F
All Tile setting are released when selecting Tile recall and the screen returns
to Full screen.
Tile ID
Select the location of the Tile by setting an ID.
Natural
he image is omitted by the distance between the screens to be naturally
T
shown.
Network Setup
- DHCP : Allocates and sets up IP automatically.
- Manual : Sets up IP address, Gateway, Subnet Mask, Primary DNS and Secondary DNS.
The setup process is complete when you select Execute, and "IP Setup Completed" is displayed
at the bottom of the screen. While "Wait for IP Setup" is displayed, you cannot use the local keys
and remote control. "Wait for IP Setup" is displayed for up to 40 seconds.
* If Network select is set to RS232C.DHCP and Manual are disabled.
Factory Reset
Select this option to return to the default factory settings.
ENG
ENGLISH
Tile Mode
23
24
CUSTOMIZING SETTINGS
Tile Mode
ENGLISH
ENG
Configuration of an integration screen is available as well as configuration of One by one Display.
• Off:
When the Tile
Mode option is
disabled
• 2X1:
When using 2 monitors
ID 2
ID 1
Tile ID
• 4X4:
When using 16 monitors
• 2X2:
When using 4 monitors
• 3X3:
When using 9 monitors
ID 1
ID 2
ID 1
ID 2
ID 3
ID 3
ID 4
ID 4
ID 5
ID 6
ID 7
ID 8
ID 9
• 5X5:
When using 25 monitors
ID 1
ID 2
ID 3
ID 4
ID 1
ID 2
ID 3
ID 4
ID 5
ID 5
ID 6
ID 7
ID 8
ID 6
ID 7
ID 8
ID 9
ID 10
ID 9
ID 10
ID 11
ID 12
ID 11
ID 12
ID 13
ID 14
ID 15
ID 13
ID 14
ID 15
ID 16
ID 16
ID 17
ID 18
ID 19
ID 20
ID 21
ID 22
ID 23
ID 24
ID 25
Tile Mode - Natural mode
To display the image naturally, the part of the image that would normally be displayed in the gap between
the monitors is omitted.
Before
After
CUSTOMIZING SETTINGS
INFORMATION settings
25
INFORMATION
2 Press the Navigation buttons to scroll to OPTION and press
SET.
3 Press the Navigation buttons to scroll to the setting or
ENG
ENGLISH
1 Press MENU to access the main menus.
Set ID
Serial No.
SW Version
IP Address
MAC Address
option you want and press SET.
-To return to the previous level, press .
4 When you are finished, press EXIT.
MENU
The available option settings are described in the following:
Setting
Description
Set ID
You can assign a unique Set ID NO (name assignment) to each product when several products
are connected for display. Specify the number (1 to 99) using the button and exit. Use the
assigned Set ID to individually control each product using the Product Control Program.
Serial No.
This menu shows the serial number of the product.
SW Version
This menu shows the software version.
IP Address
Displays a selected network's IP address.
MAC Address
Displays a selected network's MAC address.
26
MAKING CONNECTIONS
MAKING CONNECTIONS
ENGLISH
ENG
Connect various external devices to the ports on the Monitor set’s back panel.
1 Find an external device you want to connect to your Monitor set shown on the following illustration.
2 Check the connection type of the external device.
3 Go to the appropriate illustration and check the connection details.
HD Receiver
HDMI-See p.27
DVI-See p.27
AV(CVBS)-See p.28
DVD
VCR
HDMI-See p.27
DVI-See p.27
AV(CVBS)-See p.28
AV(CVBS)-See
p.28
Speaker
PC
HDMI-See p.14
DVI-See p.13
RGB-See p.13
LAN-See p.14
Camcorder/Camera
HDMI-See p.27
DVI-See p.27
AV(CVBS)-See p.28
Gaming device
HDMI-See p.27
AV(CVBS)-See
p.28
NOTE
If you connect a gaming device to the Monitor set, use the cable supplied with the gaming device.
yy
MAKING CONNECTIONS
Connect a HD receiver, DVD, or VCR player to the
Monitor set and select an appropriate input mode.
HDMI/DVI connection
Transmits the digital video signal from an external
device to the Monitor set. Connect the external
device and the Monitor set with the HDMI/DVI
cable as shown in the following illustration. To
transmit an audio signal, connect an optional audio
cable.
HDMI connection
Transmits the digital video and audio signals from
an external device to the Monitor set. Connect the
external device and the Monitor set with the HDMI
cable as shown on the following illustration.
HDMI/DVI Signal Cable
(not included)
HDMI Signal Cable
(not included)
NOTE
Use a High Speed HDMI™ Cable.
yy
RCA-PC
Audio Cable
(not included)
ENG
ENGLISH
Connecting to a HD receiver,
DVD, Camcorder, Camera,
Gaming Device or VCR
player
27
28
MAKING CONNECTIONS
AV(CVBS) connection
ENGLISH
ENG
Transmits the digital video and audio signals from
an external device to the Monitor set. Connect the
external device and the Monitor set with the BNC
cable as shown on the following illustration.
RCA-PC
Audio Cable
(not included)
BNC Cable
(not included)
TROUBLESHOOTING
29
No image is displayed
Problem
Is the product power cord
connected?
Resolution
yy See if the power cord is properly connected to the outlet.
yy See if the power switch is turned on.
yy May need service.
Power is on, power indicator is blue yy Adjust brightness and contrast again.
but the screen appears extremely
yy Backlight may need repair.
Is the power indicator light on?
dark.
The power indicator amber?
oes the 'Out of range' message
D
appear?
oes the 'No signal' message
D
appear?
yy If the product is in power saving mode, move the mouse or press any
key.
yy Turn both devices off and then back on.
yy The signal from the PC (video card) is out of the vertical or horizontal
frequency range of the product. Adjust the frequency range by
referring to the Specifications in this manual.
* Maximum resolution
RGB : 1920 x 1080 @ 60 Hz
HDMI/DVI : 1920 x 1080 @ 60 Hz
yy The signal cable between PC and product is not connected. Check
the signal cable.
yy Press the 'INPUT' menu in the remote Control to check the input
signal.
NOTE
Vertical frequency: To enable the user to watch the product display, screen image should be changed
yy
tens of times every second like a fluorescent lamp. The vertical frequency or refresh rate is the times
of image display per second. The unit is Hz.
Horizontal frequency: The horizontal interval is the time to display one vertical line. When 1 is divided
yy
by the horizontal interval, the number of horizontal lines displayed every second can be tabulated as
the horizontal frequency. The unit is kHz.
ENG
ENGLISH
TROUBLESHOOTING
30
TROUBLESHOOTING
'Unknown Product' message appears when the product is connected.
ENGLISH
ENG
Problem
Did you install the driver?
Resolution
yy Install the product driver, which is provided with the product, or
download it from the web site. (http://www.lg.com)
yy See if the plug&play function is supported by referring to the video
card user manual.
'Key Lock On' message appears.
Problem
The 'Key Lock On' message
appears when pressing the Menu
button.
Resolution
yy The Lock function prevents the OSD settings from being changed
inadvertently. To release the lock, go to Menu and Option and disable
the Key Lock option.
The screen image looks abnormal.
Problem
Resolution
yy D-Sub analog signal - Press the "AUTO" button in the remote control
to automatically select the optimal screen status that fits into the
current mode. If adjustment is not satisfactory, use the Position OSD
menu.
yy See if the video card resolution and frequency are supported by the
product. If the frequency is out of range, set to the recommended
resolution in the Control Panel "Display" Setting menu.
Do thin lines appear on the
yy D-Sub analog signal - Press the "AUTO" button in the remote control
background screen?
to automatically select an optimal screen status that fits into the
current mode. If adjustment is not satisfactory, use the Clock OSD
menu.
Horizontal noise appears or the
yy D-Sub analog signal - Press the "AUTO" button in the remote control
characters look blurred.
to automatically select an optimal screen status that fits into the
current mode. If adjustment is not satisfactory, use the Phase OSD
menu.
The screen is displayed abnormally. yy The proper input signal is not connected to the signal port. Connect
the signal cable that matches with the source input signal.
Is the screen position wrong?
TROUBLESHOOTING
31
After-image appears on the product.
After-image appears when the
product is turned off.
Resolution
yy If you use a fixed image for a long time, the pixels may be damaged
quickly. Use the screen-saver function.
The audio function does not work.
Problem
Resolution
Sound is too dull.
yy See if the audio cable is connected properly.
yy Adjust the volume.
yy See if the sound is set properly.
yy Select the appropriate equalize sound.
Sound is too low.
yy Adjust the volume.
No sound?
Screen color is abnormal.
Problem
Resolution
Screen has poor color resolution (16 colors).
yy Set the number of colors to more than 24 bits (true color) Select
Control Panel - Display - Settings - Color Table menu in Windows.
creen color is unstable or monoS
colored.
yy Check the connection status of the signal cable. Or, re-insert the PC
video card.
Do black spots appear on the
screen?
yy Several pixels (red, green, white or black color) may appear on the
screen, which can be attributable to the unique characteristics of the
LCD panel. It is not a malfunction of the LCD.
The operation does not work normally.
Problem
The power suddenly turned off.
Resolution
yy Is the sleep timer set?
yy Check the power control settings. Power interrupted.
yy "Caution, Fan Error!" If the power is turned off after this message appears, it means that
the fan is out of order.In this case, contact your local service center.
ENG
ENGLISH
Problem
32
SPECIFICATIONS
ENGLISH
ENG
SPECIFICATIONS
LCD Panel
Screen Type
Video Signal
Pixel Pitch
Max. Resolution
1192.8 mm Wide (46.96 inch) TFT (Thin Film Transistor)
LCD (Liquid Crystal Display) Panel.
Visible diagonal size : 1192.8 mm
0.5415 mm (H) x 0.5415 mm (V)
RGB : 1920 X 1080 @60Hz
HDMI/DVI : 1920 X 1080 @60Hz
- It may not be supported depending on the OS or video card type.
Recommended Resolution RGB : 1920 X 1080 @60Hz
HDMI/DVI : 1920 X 1080 @60Hz
- It may not be supported depending on the OS or video card type.
Horizontal Frequency
Vertical Frequency
Synchronization Type
Input Connector
Power
Rated Voltage
Power Consumption
Environmental
conditions
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
RGB : 30 kHz to 83 kHz
HDMI/DVI : 30 kHz to 83 kHz
RGB : 56 Hz to 75 Hz
HDMI/DVI : 56 Hz to 60 Hz
Separate Sync, Composite Sync, Digital
15-pin D-Sub type, HDMI (digital), AV(CVBS) Video,
RS-232C, LAN
AC 100-240 V~ 50/60 Hz 3.0 A
On Mode : 300 W Typ.
Sleep Mode : ≤ 1 W (RGB) / 2 W (HDMI/DVI)
Off Mode : ≤ 0.5 W
5 °C to 40 °C
10 % to 80 %
-20 °C to 60 °C
5 % to 95 %
Product specifications shown above may be changed without prior notice due to upgrade of product
functions.
SPECIFICATIONS
ENG
ENGLISH
Dimensions
(Width x Height x
Depth) / Weight
H
W
D
1117 mm x 661 mm x 118.7 mm / 28.54 kg
H
W
D
1117 mm x 757.8 mm x 302.6 mm / 32.56 kg
H
W
D
1117 mm x 661.0 mm x 118.7 mm / 29.29 kg
H
W
D
1117 mm x 757.8 mm x 302.6 mm / 33.3 kg
* Applicable only for models that support the speakers
Audio
33
RMS Audio Output
Input Sensitivity
Speaker Impedance
10 W + 10 W (R + L)
0.7 Vrms
8Ω
Product specifications shown above may be changed without prior notice due to upgrade of product
functions.
34
SPECIFICATIONS
DTV Mode
RGB (PC) supported mode
ENGLISH
ENG
Resolution
HDMI/DVI
(DTV)
480i
x
576i
x
480p
o
576p
o
Resolution
Horizontal
Vertical
Frequency(kHz) Frequency(Hz)
640 x 350
31.469
70.8
720 x 400
31.468
70.8
640 x 480
31.469
59.94
640 x 480
37.5
75
800 x 600
37.879
60.317
720p
o
800 x 600
46.875
75
1080i
o
832 x 624
49.725
74.55
1080p
o
1024 x 768
48.363
60
1024 x 768
60.123
75.029
1280 x 720
44.772
59.855
1280 x 768
47.7
60
1360 x 768
47.72
59.799
1366 x 768
47.7
60
1280 x 1024
63.981
60.02
1280 x 1024
79.98
75.02
1680 x 1050
65.290
59.954
1920 x 1080
67.5
60
Power Indicator
Mode
Monitor Set
On Mode
Blue
Sleep Mode
Amber
Off Mode
-
NOTE
HDMI/DVI(PC) supported mode
Resolution
Horizontal
Vertical
Frequency(kHz) Frequency(Hz)
640 x 480
31.469
59.94
800 x 600
37.879
60.317
1024 x 768
48.363
60
1280 x 720
44.772
59.855
1280 x 768
47.7
60
1360 x 768
47.72
59.799
1366 x 768
47.7
60
1280 x 1024
63.981
60.02
1680 x 1050
65.290
59.954
1920 x 1080
67.5
60
DTV/PC selection on RGB and HDMI/DVI
yy
inputs is available for PC resolutions : 640
x 480 / 60 Hz, 1280 x 720 / 60 Hz, 1920 x
1080 / 60 Hz and DTV resolutions : 480p,
720p, 1080p.
RS-232C
Connecting the cable
Connect the RS-232C cable as shown in the picture.
The RS-232C protocol is used for communication between the PC and product. You can turn the
yy
product on/off, select an input source or adjust the OSD menu from your PC.
RS-232C Cable
(not included)
PC
Monitor Set
RS-232C Configurations
7-Wire Configurations (Standard RS-232C cable)
PC
RXD
TXD
GND
DTR
DSR
RTS
CTS
Set
3
2
5
6
4
8
7
TXD
RXD
GND
DSR
DTR
CTS
RTS
D-Sub 9 D-Sub 9
(Female) (Female)
2
3
5
4
6
7
8
3-Wire Configurations (Not Standard)
Communication Parameter
Baud Rate : 9600 buad Rate (UART)
yy
Data Length : 8 bit
yy
Parity Bit : None
yy
Stop Bit : 1bit
yy
Flow Control : None
yy
Communication Code : ASCII code
yy
Use a crossed (reverse) cable
yy
PC
RXD
TXD
GND
DTR
DSR
RTS
CTS
2
3
5
4
6
7
8
Set
3
2
5
6
4
7
8
TXD
RXD
GND
DSR
DTR
CTS
RTS
D-Sub 9 D-Sub 9
(Female) (Female)
ENG
ENGLISH
RS-232C
35
36
RS-232C
Command reference list
ENGLISH
ENG
COMMAND
DATA
1
2
1
k
d
a
b
c
d
e
f
g
h
i
j
k
l
m
t
u
z
p
u
c
d
e
f
g
00H to 01H
02H to 09H
01H to 09H
00H to 01H
00H to 01H
00H to 64H
00H to 64H
00H to 64H
00H to 64H
00H to 64H
00H to 64H
00H to 01H
00H to 01H
00H to 64H
00H to 03H
FFH
00H to 10H
01H
Key Code
00H to 55H
00H to 64H
00H to 64H
00H to 64H
24. Tile V Size
d
h
00H to 64H
25. Tile ID Set
26. Natural Mode (In Tile mode)
27. Picture mode(PSM)
28. Sound mode
29. Fan Fault check
30. Elapsed time return
31. Temperature value
32. Lamp fault check
33. Auto Volume
34. Speaker
35. Sleep Time
d
i
j
x
y
w
l
n
p
u
v
f
00H to 19H
00H to 01H
00H to 06H
00H to 06H
FFH
FFH
FFH
FFH
00H to 01H
00H to 01H
00H to 08H
01. Power
02. Input Select
03. Aspect Ratio
04. Screen Mute
05. Volume Mute
06. Volume Control
07. Contrast
08. Brightness
09. Color
10. Tint
11. Sharpness
12. OSD Select
13. Remote Lock/ key Lock
14. Balance
15. Color Temperature
16. Abnormal state
17. ISM mode
18. Auto configuration
19. Key
20. Tile Mode
21. Tile H Position
22. Tile V Position
23. Tile H Size
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
j
j
m
d
d
d
d
d
d
d
d
d
d
d
d
f
2
3
RS-232C
COMMAND
DATA
1
2
1
f
f
g
h
i
j
k
f
l
00H to 01H
00H to 64H
00H to 09H
00H to 01H
00H to 02H
00H to 03H
00H to 01H
00H to 64H
00H to 64H
00H to 64H
00H to 64H
FFH
FFH
20H to A0H
f
f
f
f
o
f
q
r
s
t
y
z
b
f
f
f
f
f
x
2
3
ENG
ENGLISH
36. Auto Sleep
37. Power On Delay
38. Language
39. DPM Select
40. Reset
41. Power Saving
42. Power Indicator
43. H Position
44. V Position
45. H Size
46. V Size
47. Serial no.
48. S/W Version
49. Input Select
37
38
RS-232C
Transmission / Receiving protocol
ENGLISH
ENG
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
* [Command 1]: First command. (k, j, m, d, f, x)
* [Command 2]: Second command.(a to u)
* [Set ID]: Set up the Set ID number of product.
range : 01H to 63H. by setting '0', server can control all products.
* In case of operating with more than 2 sets using set ID as '0' at the same time, it should not be checked the ack
message. Because all sets will send the ack message, so it's impossible the check the whole ack messages.
* [DATA]: To transmit command data.
Transmit 'FF' data to read status of command.
* [Cr]: Carriage Return (ASCII code '0 x 0 D')
* [ ]: ASCII code Space (0 x 20)
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The Product transmits ACK (acknowledgement) based on this format when receiving normal data. At this time,
if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of
the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* If there is error, it returns NG
RS-232C
01. Power (Command: k a)
To control Power On/Off of the set.
Data 0 : Power Off
Data 1 : Power On
Acknowledgement
[a][ ][Set ID][ ][OK][Data][x]
To show the status of Power On/Off.
04. Screen Mute (Command: k d)
To select screen mute on / off.
Transmission
[k][d][ ][Set ID][ ][Data][Cr]
Data 0 : Screen mute off (Picture on)
1 : Screen mute on (Picture off)
Acknowledgement
[d][ ][Set ID][ ][OK][Data][x]
Transmission
[k][a][ ][Set ID][ ][FF][Cr]
Acknowledgement
[a][ ][Set ID][ ][OK][Data][x]
Data 0 : Power Off
9 : DPM
Data 1 : Power On
02. Input Select (Command: k b) (Main Picture Input)
To select input source for the Set.
You can also select an input source using the INPUT
button on the remote control.
Transmission
[k][b][ ][Set ID][ ][Data][Cr]
Data 2 : AV
7 : RGB (PC)
8 : HDMI (DTV)
9 : HDMI (PC)
05. Volume Mute (Command: k e)
To control On/Off of the Volume Mute.
Transmission
[k][e][ ][Set ID][ ][Data][Cr]
Data 0 : Volume Mute On (Volume Off)
1 : Volume Mute Off (Volume On)
Acknowledgement [e][ ][Set ID][ ][OK][Data][x]
Data 0 : Volume Mute On (Volume Off)
1 : Volume Mute Off (Volume On)
Acknowledgement
[b][ ][Set ID][ ][OK][Data][x]
Data 2 : AV
7 : RGB (PC)
8 : HDMI (DTV)
9 : HDMI (PC)
03. Aspect Ratio (Command: k c) (Main Picture Input)
To adjust the screen format.
You can also adjust the screen format using the ARC
(Aspect Ratio Control) button on remote control or in
the Screen menu.
Transmission
[k][c][ ][Set ID][ ][Data][Cr]
Data 1 : Normal Screen (4 : 3)
2 : Wide Screen (16 : 9)
4 : Zoom1 (AV)
5 : Zoom2 (AV)
6 : Original (AV)
7 :14 : 9 (AV)
9 : Just Scan(HD DTV),
1 : 1 (RGB PC, HDMI / DVI PC)
Acknowledgement
[c][ ][Set ID][ ][OK][Data][x]
06. Volume Control (Command: k f)
To adjust Volume.
Transmission
[k][f][ ][Set ID][ ][Data][Cr]
Data Min : 00H to Max : 64H
(Hexadecimal code)
Acknowledgement [f][ ][Set ID][ ][OK][Data][x]
Data Min : 00H to Max : 64H
* Real data mapping
0 : STEP 0
:
A : STEP 10
:
F : STEP 15
10 : STEP 16
:
64 : STEP 100
ENG
ENGLISH
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
39
40
RS-232C
ENGLISH
ENG
07. Contrast (Command: k g)
To adjust screen contrast.
You can also adjust the contrast in the Picture menu.
Transmission
[k][g][ ][Set ID][ ][Data][Cr]
Data Min : 00H to Max : 64H
Acknowledgement [g][ ][Set ID][ ][OK][Data][x]
* Refer to 'Real data mapping ’. See p.39
10. Tint (Command: k j) (Video Timing only)
To adjust the screen tint.
You can also adjust the tint in the Picture menu.
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
Data Min : 00H to Max : 64H
(Hexadecimal code)
* Refer to 'Real data mapping ’. See p.39
Acknowledgement
[j][ ][Set ID][ ][OK][Data][x]
Data Red : 00H to Green : 64H
* Tint Real data mapping
0 : Step 0 to Red
:
64 : Step 100 to Green
08. Brightness (Command: k h)
To adjust screen brightness.
You can also adjust the brightness in the Picture
menu.
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
Data Min : 00H to Max : 64H
(Hexadecimal code)
* Refer to 'Real data mapping ’. See p.39
Acknowledgement
[h][ ][Set ID][ ][OK][Data][x]
* Refer to 'Real data mapping ’. See p.39
11. Sharpness (Command: k k) (Video Timing only)
To adjust the screen Sharpness.
You can also adjust the sharpness in the Picture
menu.
Transmission
[k][k][ ][Set ID][ ][Data][Cr]
Data Min : 00H to Max : 64H
(Hexadecimal code)
* Refer to 'Real data mapping’. See p.39
Acknowledgement
[k][ ][Set ID][ ][OK][Data][x]
Data Min : 00H to Max : 64H
09. Color (Command: k i) (Video Timing only)
To adjust the screen color.
You can also adjust the color in the Picture menu.
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
Data Min : 00H to Max : 64H
(Hexadecimal code)
Acknowledgement
[i][ ][Set ID][ ][OK][Data][x]
Data Min : 00H to Max : 64H
12. OSD Select (Command: k l)
To control OSD on/off to the set.
Transmission
[k][l][ ][Set ID][ ][Data][Cr]
Data 0: OSD Off
Data 1: OSD On
Acknowledgement
[l][ ][Set ID][ ][OK][Data][x]
Data 0: OSD Off
Data 1: OSD On
RS-232C
Transmission
[k][m][ ][Set ID][ ][Data][Cr]
Data 0: Off
Data 1: On
Acknowledgement
[m][ ][Set ID][ ][OK][Data][x]
Data 0: Off
Data 1: On
16. Abnormal state (Command: k z)
Used to Read the power off status when Stand-by
mode.
Transmission
[k][z][ ][Set ID][ ][Data][Cr]
Data FF : Read
0 : Normal (Power on and signal exist)
1 : No signal (Power on)
2 : Turn the monitor off by remote control
3 : Turn the monitor off by sleep time function
4 : Turn the monitor off by RS-232C function
8 : Turn the monitor off by off time function
9 : Turn the monitor off by auto off function
Acknowledgement
[z][ ][Set ID][ ][OK][Data][x]
14. Balance (Command: k t)
To adjust the sound balance.
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
Data Min : 00H to Max : 64H
(Hexadecimal code)
* Refer to 'Real data mapping ’. See p.39
Acknowledgement
[t][ ][Set ID][ ][OK][Data][x]
Data Min : 00H to Max : 64H
* Balance : L50 to R50
17. ISM mode (Command: j p)
Used to select the afterimage preventing function.
Transmission
[j][p][ ][Set ID][ ][Data][Cr]
Data 1H : Inversion
2H : Orbiter
4H : White Wash
8H : Normal
10H : Dot Wash
Acknowledgement
[p][ ][Set ID][ ][OK][Data][x]
15. Color Temperature (Command: k u)
To adjust the screen color temperature.
Transmission
[k][u][ ][Set ID][ ][Data][Cr]
Data 0 : Medium
1 : Cool
2 : Warm
3 : User
Acknowledgement
[u][ ][Set ID][ ][OK][Data][x]
Data 0 : Medium
1 : Cool
2 : Warm
3 : User
* Running the Color Temperature command changes
the Picture Mode settings to User1.
18. Auto Configure (Command: j u)
To adjust picture position and minimize image
shaking automatically. it works only in RGB(PC)
mode.
Transmission
[j][u][ ][Set ID][ ][Data][Cr]
Data 1 : To set
Acknowledgement
[u][ ][Set ID][ ][OK][Data][x]
ENG
ENGLISH
13. Remote Lock /Key Lock (Command: k m)
To control Remote Lock on/off to the set.
This function, when controlling RS-232C, locks the
remote control and the local keys.
41
42
RS-232C
19. Key (Command: m c)
To send IR remote key code.
22. Tile V Position (Command: d f)
To set the Vertical position.
ENGLISH
ENG
Transmission
[m][c][ ][Set ID][ ][Data][Cr]
Transmission
[d][f][ ][Set ID][ ][Data][Cr]
Data Key code : Refer to ‘IR CODES’. See p.47
Acknowledgement
[c][ ][Set ID][ ][OK][Data][x]
Acknowledgement
[f][ ][Set ID][ ][OK/NG][Data][x]
20. Tile Mode (Command: d d)
Change a Tile Mode.
23. Tile H Size (Command: d g)
To set the Horizontal size.
Transmission
[d][d][ ][Set ID][ ][Data][Cr]
Transmission
[d][g][ ][Set ID][ ][Data][x]
Data
Description
00 or 11
12
13
14
Tile mode is off.
1 x 2 mode (column x row)
1 x 3 mode
1 x 4 mode
...
5 x 5 mode
...
55
Data Min : 00H to Max : 64H
* Refer to 'Real data mapping ’. See p.39
Data Min : 00H to Max : 64H
* Refer to 'Real data mapping ’. See p.39
Acknowledgement
[g][ ][Set ID][ ][OK/NG][Data][x]
* The data can not be set to 0X or X0 except 00.
Acknowledgement
[d][ ][Set ID][ ][OK/NG][Data][x]
24. Tile V Size (Command: d h)
To set the Vertical size.
Transmission
[d][h][ ][Set ID][ ][Data][x]
Data Min : 00H to Max : 64H
* Refer to 'Real data mapping ’. See p.39
21. Tile H Position (Command: d e)
To set the Horizontal position.
Acknowledgement
[h][ ][Set ID][ ][OK/NG][Data][x]
Transmission
[d][e][ ][Set ID][ ][Data][Cr]
Data Min : 00H to Max : 64H
* Refer to 'Real data mapping ’. See p.39
Acknowledgement
[e][ ][Set ID][ ][OK/NG][Data][x]
25. Tile ID Set (Command: d i)
To assign the Tile ID for Tiling function.
Transmission
[d][i][ ][Set ID][ ][Data][x]
Data Min : 00H to Max : 19H
(Hexadecimal code)
Acknowledgement
[i][ ][Set ID][ ][OK/NG][Data][x]
RS-232C
26. Natural Mode (In Tile mode)(Command: d j)
To assign the Tile Natural mode for Tiling function.
29. Fan Fault check (Command: d w)
To check the Fan fault of the Set.
Transmission
[d][w][ ][Set ID][ ][Data][x]
Data 0 : Natural Off
1 : Natural On
ff : Read Status
* The data is always FF (in Hex).
Data ff : Read Status
Acknowledgement
[j][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement
[w][ ][Set ID][ ][OK/NG][Data][x]
* Data is the status value of the Fan fault.
Data 0 : Fan fault
1 : Fan Ok
2 : N/A (Not Avaliable)
27. Picture Mode (Command: d x)
To adjust the picture mode.
Transmission
[d][x][ ][Set ID][ ][Data][x]
Data Structure
Data(Hex)
Mode
00
01
02
03
04
05
06
Vivid
Standard
Cinema
Sport
Game
User1
User2
Acknowledgement
[x][ ][Set ID][ ][OK/NG][Data][x]
28. Sound Mode (Command: d y)
To adjust the Sound mode.
Transmission
[d][y][ ][Set ID][ ][Data][x]
30. Elapsed time return (Command: d l)
To read the elapsed time.
Transmission
[d][l][ ][Set ID][ ][Data][x]
* The data is always FF(in Hex).
Acknowledgement
[l][ ][Set ID][ ][OK/NG][Data][x]
* The data is always FF(in Hex).
(Hexadecimal code)
31. Temperature value (Command: d n)
To read the inside temperature value.
Transmission
[d][n][ ][Set ID][ ][Data][x]
Data Structure
Data(Hex)
Mode
00
01
02
03
04
05
06
Clear Voice
Standard
Music
Cinema
sport
Game
User
Acknowledgement
[y][ ][Set ID][ ][OK/NG][Data][x]
* The data is always FF(in Hex).
Acknowledgement
[n][ ][Set ID][ ][OK/NG][Data][x]
* The data is 1 byte long in Hexadecimal.
ENG
ENGLISH
Transmission
[d][j][ ][Set ID][ ][Data][x]
43
44
RS-232C
32. Lamp fault Check (Command: d p)
To check lamp fault.
ENGLISH
ENG
Transmission
[d][p][ ][Set ID][ ][Data][x]
* The data is always FF(in Hex).
Acknowledgement
[p][ ][Set ID][ ][OK/NG][Data][x]
* The data is 1 byte long in Hexadecimal.
Data 0 : Lamp Fault
1 : Lamp Ok
35. Sleep Time (Command: f f)
Set Sleep Time.
Transmission
[f][f][ ][Set ID][ ][Data][Cr]
Data 00 : Off
01 : 10
02 : 20
03 : 30
04 : 60
05 : 90
06 : 120
07 : 180
08 : 240
(Orderly)
Acknowledgement
[f][ ][Set ID][ ][OK/NG][Data][x]
33. Auto volume (Command: d u)
Automatically adjust the volume level.
Transmission
[d][u][ ][Set ID][ ][Data][x]
Data 0: Off
Data 1: On
Acknowledgement
[u][ ][Set ID][ ][OK/NG][Data][x]
36. Auto Sleep (Command: f g)
Set Auto Sleep.
Transmission
[f][g][ ][Set ID][ ][Data][Cr]
Data 0: Off
Data 1: On
Acknowledgement
[g][ ][Set ID][ ][OK/NG][Data][x]
34. Speaker (Command: d v)
Turn the speaker on or off.
Transmission
[d][v][ ][Set ID][ ][Data][x]
Data 0: Off
Data 1: On
Acknowledgement
[v][ ][Set ID][ ][OK/NG][Data][x]
37. Power On Delay (Command: f h)
Set the schedule delay when the power is turned on
(Unit: second).
Transmission
[f][h][ ][Set ID][ ][Data][Cr]
Data : 00H to 64H (Data value)
* Refer to 'Real data mapping ’. See p.39
Acknowledgement
[h][ ][Set ID][ ][OK/NG][Data][x]
RS-232C
38. Language (Command: f i)
Set the OSD language.
Data 0 : English
1 : French
2 : German
3 : Spanish
4 : Italian
5 : Portuguese
6 : Chinese
7 : Japanese
8 : Korean
9 : Russian
Acknowledgement
[i][ ][Set ID][ ][OK/NG][Data][x]
41. Power saving (Command: f l)
To set the Power saving mode.
Transmission
[f][l][ ][Set ID][ ][Data][Cr]
Data 0 : Off
1 : Level 1
2 : Level 2
3 : Level 3
Acknowledgement
[l][ ][Set ID][ ][OK/NG][Data][x]
42. Power Indicator (Command: f o)
To set the LED for Power Indicator
Transmission
[f][o][ ][Set ID][ ][Data][Cr]
Data 00 : Off
01 : On
Acknowledgement
[o][ ][Set ID][ ][OK/NG][Data][x]
39. DPM Select (Command: f j)
Set the DPM (Display Power Management) function.
Transmission
[f][j][ ][Set ID][ ][Data][Cr]
Data 0 : Off
1 : On
Acknowledgement
[j][ ][Set ID][ ][OK/NG][Data][x]
43. H Position (Command : f q)
To set the Horizontal position
Transmission
[f][q][ ][Set ID][ ][Data][Cr]
Data : 00H to 64H
* Refer to 'Real data mapping ’. See p.39
Acknowledgement
[q][ ][Set ID][ ][OK/NG][Data][x]
40. Reset (Command: f k)
Set the DPM (Display Power Management) function.
Transmission
[f][k][ ][Set ID][ ][Data][Cr]
Data 0 : Picture Reset
1 : Screen Reset
2 : Factory Reset
Acknowledgement
[k][ ][Set ID][ ][OK/NG][Data][x]
44. V Position (Command : f r)
To set the Vertical positionTransmission
[f][r][ ][Set ID][ ][Data][Cr]
Data : 00H to 64H
* Refer to 'Real data mapping ’. See p.39
Acknowledgement
[r][ ][Set ID][ ][OK/NG][Data][x]
ENG
ENGLISH
Transmission
[f][i][ ][Set ID][ ][Data][Cr]
45
46
RS-232C
45. H Size (Command : f s)
To set the Horizontal size.
ENGLISH
ENG
Transmission
[f][s][ ][Set ID][ ][Data][Cr]
Data : 00H to 64H
* Refer to 'Real data mapping ’. See p.39
Acknowledgement
[s][ ][Set ID][ ][OK/NG][Data][x]
* H Size Real Data Mapping
[Data1]
0x00: Step 0
0x0A: Step 10
0x14: Step 20
0x1E: Step 30
0x28: Step 40
0x32: Step 50
0x3C: Step 60
0x46: Step 70
0x50: Step 80
0x5A: Step 90
0x64: Step 100
47. Serial no. (Command: f y)
Check the Serial no.
Transmission
[f][y][ ][Set ID][ ][Data][Cr]
Data FF (to read the serial numbers)
Acknowledgement
[y][ ][Set ID][ ][OK/NG][Data1] to [Data13][x]
* The data format is ASCII Code.
48. S/W Version (Command: f z)
Check the software version.
Transmission
[f][z][ ][Set ID][ ][Data][Cr]
Data FF : Read
Acknowledgement
[z][ ][Set ID][ ][OK/NG][Data][x]
46. V Size (Command : f t)
To set the Vertical size
Transmission
[f][t][ ][Set ID][ ][Data][Cr]
Data : 00H to 64H
* Refer to 'Real data mapping ’. See p.39
Acknowledgement
[t][ ][Set ID][ ][OK/NG][Data][x]
* V Size Real Data Mapping
[Data1]
0x00: Step 0
0x0A: Step 10
0x14: Step 20
0x1E: Step 30
0x28: Step 40
0x32: Step 50
0x3C: Step 60
0x46: Step 70
0x50: Step 80
0x5A: Step 90
0x64: Step 100
49. Input Select (Command: x b)
To select input source for the Set.
Transmission
[x][b][ ][Set ID][ ][Data][Cr]
Data 20H : AV
60H : RGB (PC)
90H : HDMI/DVI (DTV)
A0H : HDMI/DVI (PC)
Acknowledgement
[b][ ][Set ID][ ][OK/NG][Data][x]
Data 20H : AV
60H : RGB (PC)
90H : HDMI/DVI (DTV)
A0H : HDMI/DVI (PC)
RS-232C
47
IR CODES
Function
VOL( )
VOL( )
POWER ON/OFF
POWER ON
POWER OFF
MUTE
AV
INPUT
SLEEP
MENU
EXIT
PSM
SET
Number Key 0
Number Key 1
Number Key 2
Number Key 3
Number Key 4
Number Key 5
Number Key 6
Number Key 7
Number Key 8
Number Key 9
AV
RGB PC
HDMI/DVI
ARC
ARC (4 : 3)
ARC (16 : 9)
ARC (ZOOM)
AUTO CONFIG
Note
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button (Power On / Off)
Discrete IR Code (Only Power On)
Discrete IR Code (Only Power Off)
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
Discrete IR Code(Input AV Selection)
Discrete IR Code(Input RGB PC Selection)
Discrete IR Code(Input HDMI/DVI Selection)
R/C Button
Discrete IR Code(Only 4 : 3 mode)
Discrete IR Code(Only 16 : 9 mode)
Discrete IR Code(Only ZOOM1, ZOOM2 mode)
Discrete IR Code
ENG
ENGLISH
Code(Hex)
00
01
02
03
08
C4
C5
09
98
0B
0E
43
5B
6E
44
10
11
12
13
14
15
16
17
18
19
5A
D5
C6
79
76
77
AF
99
Make sure to read the Safety Precautions
before using the product.
Keep the Owner's Manual(CD) in an accessible
place for future reference.
The model and serial number of the SET is
located on the back and one side of the SET.
Record it below should you ever need service.
MODEL
SERIAL
Temporary noise is normal when powering ON or
OFF this device.
Download PDF