LG | 55LV75A | LG 55LV75A-7B Owner’s Manual

OWNER’S MANUAL
LG Digital
Signage
(MONITOR SIGNAGE)
Please read this manual carefully before operating your set and retain it for
future reference.
55LV75A
55LV77A
www.lg.com
Copyright © 2018 LG Electronics Inc. All Rights Reserved.
2
TABLE OF CONTENTS
ENGLISH
ENG
TABLE OF CONTENTS
4LICENSES
5
ASSEMBLING AND
PREPARING
5Accessories
6Parts
7
To Install in a Portrait Layout
7
Remove L-brackets before Installation
8
STORAGE METHOD FOR PANEL
PROTECTION
25ENTERTAINMENT
25
- Connecting to a Wired Network
26
- Network Status
27
- Connecting USB Storage Devices
28
- Browsing Files
30
- Viewing Movies
33
- Viewing Photos
36
- Listening to Music
38
- Viewing the Contents List
39
-DivX® VOD Guide
40
- Using PIP/PBP
8
- Correct Method
8
- Incorrect Method
9
Installing on a Wall
41 CUSTOMIZING SETTINGS
11
EXTERNAL EQUIPMENT SETUP
41
Accessing the Main Menus
11
- IR RECEIVER
42
- PICTURE Settings
12
Tiling Displays
45
- AUDIO Settings
12
- How to Mount the Set
46
- TIME Settings
13
- How to Join Sets
47
- OPTION Settings
52
Picture ID
53
- NETWORK Settings
14 REMOTE CONTROL
16
Displaying the Device Name Connected
to an Input Port
17 USING THE MONITOR SET
17
Connecting to a PC
17
- RGB Connection
18
- DVI Connection
18
- HDMI Connection
19
- Display Port Connection
19
- IR Receiver Connection
20
Adjusting the Screen
20
- Selecting an Image Mode
20
- Customizing Image Options
21
- Customizing PC Display Options
22
Using Additional Options
22
- Adjusting Aspect Ratio
24
- Using the Input List
54 MAKING CONNECTIONS
55
External Device Connection
55
- DVI Connection
55
- HDMI Connection
56
- Component Connection
56
- AV(CVBS) Connection
57
- Audio Connection
57
Connecting to the LAN
57
Connecting to a USB
58
Daisy Chain Monitors
59
- Using the Multi Display Mode function
60TROUBLESHOOTING
62SPECIFICATIONS
TABLE OF CONTENTS
67 CONTROLLING THE MULTIPLE
PRODUCT
67
Connecting the cable
67
RS-232C Configurations
67
Communication Parameter
68
Command Reference List
70
Transmission / Receiving Protocol
ENG
ENGLISH
66 IR CODES
3
4
LICENSES
ENGLISH
LICENSES
Supported licenses may differ by model. For more information of the licenses, visit www.lg.com.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.
This DivX Certified® device has passed rigorous testing to ensure it plays DivX® video.
To play purchased DivX movies, first register your device at vod.divx.com. Find your registration code in the
DivX VOD section of your device setup menu.
DivX Certified® to play DivX® video up to HD 1080p, including premium content.
DivX®, DivX Certified® and associated logos are trademarks of DivX, LLC and are used under license.
Covered by DivX Patents 7,295,673; 7,515,710; RE45,052; and others available at [www.divx.com/patents]
Manufactured under license from Dolby Laboratories. Dolby, Dolby Vision, Dolby Audio, Dolby Atmos, and
the double-D symbol are trademarks of Dolby Laboratories.
NOTE
Product damage from moving or changing the installation location is not covered by warranty.
yy
The warranty will not cover any damages caused by using the product in an excessively dusty
yy
environment.
ASSEMBLING AND PREPARING
5
Accessories
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual product
and accessories.
CD (Owner's Manual) /
Cards
Power Cord
IR Receiver
DP Cable
Remote Control
and Batteries
M4 x L6
Screws (8 ea)
M6 x L10
Screws (4 ea)
RS-232C Cable
Tiling Guide (4 ea)
Mounting Cable Tie (2 ea)
(For Cable Arrangement)
CAUTION
Do not use any pirated items to ensure the safety and product life span.
yy
Any damages or injuries by using pirated items are not covered by the warranty.
yy
NOTE
The accessories supplied with your product may vary depending on the model.
yy
Product specifications or contents in this manual may be changed without prior notice due to upgrade
yy
of product functions.
SuperSign SW & Manual
yy
- Downloading from the LG Electronics website.
- Visit the LG Electronics website (http://partner.lge.com) and download the latest software for your
model.
ENG
ENGLISH
ASSEMBLING AND PREPARING
6
ASSEMBLING AND PREPARING
Parts
ENGLISH
ENG
ASSEMBLING AND PREPARING
7
To Install in a Portrait Layout
Remove L-brackets before Installation
Remove the L-brackets from each corner of the monitor before installing it.
NOTE
Keep the removed L-brackets and use them when moving the monitor later.
yy
ENG
ENGLISH
When installing in a Portrait Layout, rotate the monitor clockwise 90 degrees (when facing the screen).
8
ASSEMBLING AND PREPARING
STORAGE METHOD FOR PANEL PROTECTION
ENGLISH
ENG
Correct Method
Incorrect Method
Panel
Panel
If the product needs to be set upright, hold both
sides of the product, and tilt backward carefully
for. Do not let the panel not to touch the floor.
Panel
If the product is tilted onto the bezel, the bottom of
the panel may be damaged.
Cushion
Panel
When laying down the product, lay a cushion on a
flat floor. Put the product on it with the panel of
the product facing down.
Panel
If the product is tilted onto the edge of the panel,
the panel may be damaged.
If there is not a cushion available, ensure the floor
is clean and then lay the product down carefully
with the panel facing either upward or downward.
At this time, be careful for objects not to fall on the
panel.
ASSEMBLING AND PREPARING
Installing on a Wall
CAUTION
10 cm
20 cm
10 cm
10 cm
Install the monitor at least 20 cm away from the
wall and leave about 10 cm of space at each side
of the monitor to ensure sufficient ventilation.
Use the wall mount plate and screws that comply
with the VESA standard.
NOTE
Do not install the product in a place with
no ventilation (e.g., on a bookshelf or in a
closet) or on a carpet or cushion. If there is
no other option but to mount the product on
the wall, make sure that sufficient ventilation
is provided before installation.
- Failure to do so may result in a fire due to
the increase in the internal temperature.
Disconnect the power cord first, and then
yy
move or install the monitor set. Otherwise
electric shock may occur.
If you install the monitor set on a ceiling or
yy
slanted wall, it may fall and result in severe
injury.
Do not over tighten the screws as this may
yy
cause damage to the monitor set and void
your warranty.
Use the screws and wall mounts that meet
yy
the VESA standard. Any damages or injuries
by misuse or using an improper accessory
are not covered by the warranty.
To prevent injury, this apparatus must be
yy
securely attached to the wall in accordance
with the installation instructions. (This only
pertains to Australia and New Zealand.)
ENG
ENGLISH
To install the Monitor on a wall (optional),
use the VESA screws provided as accessories to
fasten it.
10 cm
9
10
ASSEMBLING AND PREPARING
Securing the product to a wall (optional)
ENGLISH
ENG
(Depending on model)
1 Insert and tighten the eye-bolts, or product
brackets and bolts on the back of the product.
-If there are bolts inserted at the eye-bolts
position, remove the bolts first.
2 Mount the wall brackets with the bolts to the
wall.
Match the location of the wall bracket and the
eye-bolts on the rear of the product.
3 Connect the eye-bolts and wall brackets tightly
with a sturdy rope.
Make sure to keep the rope horizontal with the
flat surface.
CAUTION
Make sure that children do not climb on or
yy
hang on the product.
NOTE
Use a platform or cabinet that is strong and
yy
large enough to support the product securely.
Brackets, bolts, and ropes are optional. You
yy
can obtain additional accessories from your
local dealer.
The illustration shows a general example of
yy
installation and may look different from the
actual product.
WARNING
If a product is not positioned in a sufficiently
yy
stable location, it can be potentially
hazardous due to falling. Many injuries,
particularly to children, can be avoided by
taking simple precautions such as:
»» Using cabinets or stands recommended
by the manufacturer of the product.
»» Only using furniture that can safely
support the product.
»» Ensuring the product is not overhanging
the edge of the supporting furniture.
»» Not placing the product on tall furniture
(for example, cupboards or bookcases)
without anchoring both the furniture and
the product to a suitable support.
»» Not standing the product on cloth or other
materials placed between the product
and supporting furniture.
»» Educating children about the dangers of
climbing on furniture to reach the product
or its controls.
ASSEMBLING AND PREPARING
11
EXTERNAL EQUIPMENT SETUP
This allows a remote control sensor to be placed in a custom location. Then that display can control other
displays via an RS-232C cable.
ENG
ENGLISH
IR RECEIVER
12
ASSEMBLING AND PREPARING
Tiling Displays
Example of 2 x 2 Tiling
Using the screws for attaching the VESA wall mount, mount the set to the wall mount plate or the wall.
Screws for attaching the VESA
wall mount (M6)
Screws (15-M4)
≤ 6 mm
600
400
ENGLISH
ENG
How to Mount the Set
ASSEMBLING AND PREPARING
13
How to Join Sets
Set 4 joined to the rest of the sets
(2 x 2 tiling)
2After joining the sets, use the tiling guide to adjust the gap between the sets.
3 Now the 2 x 2 tiling is complete.
You can tile in various combinations, such as 3 x 3.
NOTE
The load applied to each set should be supported by the wall mount plate or the wall using a VESA
yy
wall mount (600 x 400).
The load applied to each set should be supported by the wall mount plate using a VESA wall mount.
yy
(Each set must be firmly mounted to the wall mount plate or the wall.)
You may mount the set without using the tiling guide; this does not affect the performance of the
yy
device.
The screws are enclosed with the other components in the box, including the tiling guides.
yy
ENG
ENGLISH
1Join other sets using screws for fixing the VESA wall mount in the same way as above.
14
REMOTE CONTROL
ENGLISH
ENG
REMOTE CONTROL
The descriptions in this manual are based on the buttons of the remote control. Please read this manual
carefully and use the monitor set correctly.
To replace batteries, open the battery cover, replace batteries (1.5 V AAA) matching and ends to the
label inside the compartment, and close the battery cover.
To remove the batteries, perform the installation actions in reverse.
CAUTION
Do not mix old and new batteries, as this
yy
may damage the remote control.
Make sure to point the remote control to the
yy
remote control sensor on the monitor set.
(POWER)
Turns the monitor set on or off.
ENERGY SAVING( )
Reduces power consumption
by adjusting peak screen
brightness.
MONITOR ON
Turn on the monitor.
MONITOR OFF
Turn off the monitor.
INPUT
Selects the input mode.
3D
This button does not apply to
this model.
1/a/A Button
Toggles between numerical
and alphabetical.
Number and Alphabet Buttons
Enters numerical or alphabetical
characters depending on the
setting.
ARC
Selects the Aspect Ratio
Mode.
Volume Up / Down
This button does not apply to
this model.
CLEAR
Deletes the entered numerical
or alphabetical character.
PSM
Selects the Picture Status
Mode.
BRIGHTNESS Key
Adjust the brightness by
pressing the Up and Down
buttons on the remote control.
In USB mode, the OSD menu
has the Page function to move
to the next file list.
MUTE
Mutes all sounds.
BACK
ID
TILE
EXIT
REMOTE CONTROL
15
ENG
ENGLISH
INFO
Displays the input
information.
SETTINGS
Accesses the main menus
or saves your input and exit
menus.
OK
Selects menus or options and
confirms your input.
BACK
Allows the user to move back
one step in user interaction
function.
Allows you to control various
multimedia devices simply
by using the remote control
through the SimpLink menu.
(It may not be supported
depending on the model.)
ID ON/OFF
When the number of Picture
ID is equal to Set ID you can
control the monitor which
you want in the multi display
condition.
AUTO
Automatically adjusts picture
position and minimizes image
instability.(RGB input only)
W.BAL
Enters the White Balance
menu.
S.MENU
(SuperSign Menu Key)
This button does not apply to
this model.
Navigation Buttons
Scrolls through menus or
options.
EXIT
Clears all on-screen displays
and returns to Monitor set
viewing from any menu.
TILE
Selects the TILE Mode.
USB Menu control buttons
Controls media playback.
16
REMOTE CONTROL
Displaying the Device Name Connected to an Input Port
ENGLISH
ENG
Display which devices are connected to which
external input ports.
1Access the Input list screen and press the blue
(input label) button on the remote control.
2You can assign an input label for every input
except USB.
Input Label
HDMI
DVI-D
Display Port
Close
NOTE
External inputs supported: HDMI, DVI-D,
yy
Display Port
Labels available: PC, DTV
yy
The input labels are displayed on the Input
yy
Label screen or at the top left of the screen
when you change the external input setting.
For DTV/PC-compatible signals, such as
yy
1080p 60 Hz, the screen settings may
change according to the input label. The Just
Scan option is available if a PC is connected
as an external device.
USING THE MONITOR SET
17
Connecting to a PC
RGB Connection
Your Monitor set supports the Plug & Play* feature.
Transmits the analog video signal from your PC to
the monitor set. Connect the PC and the Monitor
set with the 15-pin signal cable as shown the
following illustrations.
Select RGB input.
* Plug & Play: A PC will have a built-in driver for
the monitor, no extra software is needed.
Back of the product.
NOTE
It is recommended to use the monitor set
yy
with the HDMI connection for the best image
quality.
To comply with the specifications of the
yy
product, use a shielded interface cable with
ferrite core, such as a D-sub 15-pin cable
and DVI/HDMI cable.
If you turn the monitor set on when the set
yy
becomes cold, the screen may flicker. This is
normal.
Some red, green, or blue spots may appear
yy
on the screen. This is normal.
To minimize the impact of electromagnetic
yy
waves, secure the cables with cable ties.
15-pin D-Sub Signal
Cable (Max 3m)
Macintosh Adapter
(not included)
(not
included)
(not included)
PC/ MAC
CAUTION
Connect the signal
yy
input cable and tighten
it by turning the screws
clockwise.
Do not press the screen with your finger for
yy
a long time as this may result in temporary
distortion on the screen.
Avoid displaying a fixed image on the
yy
screen for a long period of time to prevent
image burn. Use a screensaver if possible.
NOTE
Use the standard
yy
Macintosh adapter since
an incompatible adapter
is available in the market.
(Different signaling system)
Apple computers may require an adapter to
yy
connect to this monitor. Call or visit their web
site for more information.
ENG
ENGLISH
USING THE MONITOR SET
18
USING THE MONITOR SET
ENGLISH
ENG
DVI Connection
HDMI Connection
Transmits digital video signal from your PC to
the monitor set. Connect the PC and the monitor
set with the DVI cable as shown the following
illustrations.
Select DVI input.
Transmits digital video and audio signals from your
PC to the monitor set. Connect the PC and the
monitor set with the HDMI cable as shown in the
following illustrations.
Select HDMI input.
Back of the product.
(not
included)
Back of the product.
(not included)
(not included)
PC
PC
NOTE
Use a High Speed HDMI®/TM Cable.
yy
Please check the PC environment if you
yy
cannot hear audio in HDMI mode. Some PCs
require you to manually change the default
audio output to HDMI.
If you want to use HDMI-PC mode, you must
yy
set the input label to PC mode.
When HDMI PC is used, a compatiblity
yy
problem might occur.
Use a certified cable with the HDMI logo
yy
attached. If you do not use a certified HDMI
cable, the screen may not display or a
connection error may occur.
Recommended HDMI cable types
yy
- High-Speed HDMI®/TM cable
- High-Speed HDMI®/TM cable with Ethernet
USING THE MONITOR SET
IR Receiver Connection
Transmits digital video and audio signals from
your PC to the Monitor. Connect the PC and the
Monitor with the Display Port cable as shown in
the following illustrations.
Select Display Port input source.
Allows the use of IR receiver extension.
Back of the product.
PC
NOTE
Sound may not be available depending on
yy
the DP version of your PC.
Back of the product.
ENG
ENGLISH
Display Port Connection
19
20
USING THE MONITOR SET
ENGLISH
ENG
Adjusting the Screen
Customizing Image Options
Selecting an Image Mode
Customize basic and advanced options of each
image mode for the best screen performance.
Display images in its optimized settings by
selecting one of the preset image modes.
1Press SETTINGS to access the main menus.
1Press SETTINGS to access the main menus.
2 Press the navigation buttons to scroll to
PICTURE and press OK.
3 Press the navigation buttons to scroll to
Picture Mode and press OK.
4 Press the navigation buttons to scroll to an
image mode you want and press OK.
Mode
2 Press the navigation buttons to scroll to
PICTURE and press OK.
3 Press the navigation buttons to scroll to
Picture Mode and press OK.
4 Press the navigation buttons to scroll to an
image mode you want and press OK.
5 Select and adjust following options, and then
press OK.
Description
Vivid
Adjusts the video image for the retail
environment by enhancing the contrast,
brightness, color, and sharpness.
Standard
Adjusts the image for the normal
environment.
Cinema
Optimizes the video image for a cinematic
look to enjoy movies as if you are in a
movie theater.
Sport
Optimizes the video image for high and
dynamic actions by emphasizing primary
colors such as white, grass, or sky blue.
Game
Optimizes the video image for a fast
gaming screen such as PCs or games.
5 When you are finished, press EXIT.
Option
Description
Backlight
djusts the brightness of the screen
A
by controlling the LCD backlight. If
you decrease the brightness level,
the screen becomes darker and the
power consumption will be reduced
without any video signal loss.
Contrast
Increases or decreases the gradient
of the video signal. You may use
Contrast when the bright part of the
picture is saturated.
Brightness
Adjusts the base level of the signal in
the picture. You may use Brightness
when the dark part of the picture is
saturated.
Sharpness
Adjusts the level of crispness in the
edges between the light and dark
areas of the picture. The lower the
level, the softer the image.
Color
Adjusts intensity of all colors.
Tint
Adjusts the balance between red and
green levels.
Color Temp.
Set to warm to enhance hotter Colors
such as red, or set to cool to make
picture bluish.
Advanced
Control
Customizes the advanced options.
Refer to the Advanced image options.
Picture Reset
Restores the options to the default
setting.
When you return to the previous menu, press
BACK.
6 When you are finished, press EXIT.
When you return to the previous menu, press
BACK.
USING THE MONITOR SET
21
Customizing PC Display Options
1Press SETTINGS to access the main menus.
2 Press the navigation buttons to scroll to
PICTURE and press OK.
3 Press the navigation buttons to scroll to Screen
and press OK.
4 Select and adjust following options, and then
press OK.
Option
Description
Resolution
Selects a proper resolution.
Auto
Config.
Sets to adjust the screen position, clock,
and phase automatically. The displayed
image may be unstable for a few seconds
while the configuration is in progress.
Position/
Adjusts the options when the picture is
Size/Phase not clear, especially when characters are
shaky, after the auto configuration.
Reset
Restores the options to the default
setting.
5 When you are finished, press EXIT.
When you return to the previous menu, press
BACK.
ENG
ENGLISH
Customize options of each image mode for the
best image quality.
This function works in the following mode:
yy
RGB [PC] mode.
22
USING THE MONITOR SET
Using Additional Options
ENGLISH
ENG
Adjusting Aspect Ratio
Resize the image to view the image at its optimal size by pressing ARC while you are watching Monitor set.
CAUTION
If a fixed image displays on the screen for a long period of time, it could be imprinted and become
yy
a permanent disfigurement on the screen. This is image burn or burn-in and not covered by the
warranty.
If the aspect ratio is set to 4:3 for a long period of time, image burn may occur on the letterboxed area
yy
of the screen.
NOTE
You can also change the image size by accessing the main menus.
yy
MODE
AV
Component
RGB
DVI-D
HDMI
Display Port
PC
DTV
PC
DTV
PC
DTV
PC
o
o
o
o
o
o
o
o
o
x
o
x
o
x
o
x
x
x
o
x
o
x
o
x
o
4:3
o
o
o
o
o
o
o
o
o
Zoom
o
o
x
o
x
o
x
o
x
Cinema Zoom 1~16
o
o
x
o
x
o
x
o
x
Aspect Ratio
16:9
o
Just Scan
x
1:1
USING THE MONITOR SET
23
- 4:3 : This selection will allow you to view a
picture with an original 4:3 aspect ratio, black
bars will appear on both the left and right of the
screen.
- Just Scan : This Selection will allow you view
the picture of best quality without loss of original
picture in high resolution image. Note: If there is
noise in original Picture, You can see the noise
at the edge.
- Zoom : This selection will allow you to view the
picture without any alteration, while filling the
entire screen. However, the top and bottom of
the picture will be cropped.
Just Scan
- 1:1 : The aspect ratio is not adjusted from the
original. (Only Display Port PC, HDMI PC,
DVI-D PC, RGB PC)
- Cinema Zoom 1~16 : Choose Cinema Zoom
when you want to enlarge the picture in correct
proportion.
Note: When enlarging or reducing the picture,
the image may become distorted.
ENG
ENGLISH
- 16:9 : This selection will allow you to adjust the
picture horizontally, in linear proportion, to fill the
entire screen(useful for viewing 4:3 formatted
DVDs).
24
USING THE MONITOR SET
Using the Input List
ENGLISH
ENG
Selecting an Input Source
1Press INPUT to access the input source list.
2 Press the navigation buttons to scroll to one of
the input sources and press OK.
Input source
Description
AV
Watch video from a VCR or other
external devices.
Component
Watch the content from a DVD or
other external devices, or through a
digital set-top box.
RGB
View a PC display on the screen.
HDMI
Watch contents from a PC, DVD
of Digital set-top box other high
definition devices.
DVI-D
View a PC display on the screen.
Display Port
Watch contents in a PC, DVD
of Digital set-top box other high
definition devices.
USB
Plays the multimedia file saved in
the USB.
ENTERTAINMENT
25
Connecting to a Wired Network
Connect the display to a local area network (LAN)
via the LAN port as shown on the following illustration and set up the network settings.
Only supports wired network connection.
After making a physical connection, a small
number of networks may require the display network settings to be adjusted. For most networks,
the display will connect to automatically without
any adjustments.
For detail information, contact your internet provider or router manual.
To set up the network settings: (Even if your display has already connected automatically, running
setup again will not harm anything),
1Press SETTINGS to access the main menus.
2 Press the navigation buttons to scroll to NETWORK and press OK.
3 Press the navigation buttons to select Network
Setting and press OK.
4 If you already set Network Setting, select
Resetting. The new connection settings resets
the current network settings.
5Select IP Auto Setting or IP Manual Setting.
LAN
Router
Router
@
LAN
Cable modem
Internet
Internet
WAN
-IP Manual Setting: Press the navigation and
number buttons. IP addresses will need to be
input manually.
-IP Auto Setting: Select this if there is a
DHCP server (Router) on the local area network (LAN) via wired connection, the display
will automatically be allocated an IP address.
If you’re using a broadband router or broadband modem that has a DHCP (Dynamic
Host Configuration Protocol) server function.
The IP address will automatically be determined.
6 When you are finished, press EXIT.
ETHERNET
Cable modem
CAUTION
yy
Do not connect a modular phone cable to
the LAN port.
yy
Since there are various connection methods, please follow the specifications of your
telecommunication carrier or internet service
provider.
CAUTION
yy
Network setting menu will not be available until the display connected to physical
network.
yy
Since there are various connection methods, please follow the specifications of your
telecommunication carrier or internet service
provider.
ENG
ENGLISH
ENTERTAINMENT
26
ENTERTAINMENT
NOTE
ENGLISH
ENG
yy
If you want to access the Internet directly on
your display, the Internet connection should
always be on.
yy
If you cannot access the Internet, check
the network conditions from a PC on your
network.
yy
When you use Network Setting, check the
LAN cable or check if DHCP in the router is
turned on.
yy
If you do not complete the network settings,
the network may not work properly.
yy
A DSL modem is required to use DSL service
and a cable modem is required to use cable
modem service. Depending on the access
method of and subscriber agreement with your
ISP, you may not be able to use the internet
connection feature contained in this display or
you may be limited to the number of devices
you can connect at the same time. (If your ISP
limits sub-scription to one device, this display
may not be allowed to connect when a PC is
already connected.)
yy
The use of a “Router” may not be allowed or its
usage may be limited depending on the policies and restrictions of your ISP. For details,
contact your ISP directly.
Tips for Network Setting
yy
Use a standard LAN cable with this display.
Cat5 or better with a RJ45 connector.
yy
Many network connection problems during set
up can often be fixed by re-setting the router
or modem. After connecting the display to the
network, quickly power off and/or disconnect
the power cable of the network router or cable
modem. Then power on and/or connect the
power cable again.
yy
Depending on the Internet service provider
(ISP), the number of devices that can receive
Internet service may be limited by the applicable terms of service. For details, contact your
ISP.
yy
LG is not responsible for any malfunction of the
display and/or the Internet connection feature
due to communication errors/malfunctions associated with your Internet connection, or other
connected equipment.
yy
LG is not responsible for problems within your
internet connection.
yy
You may experience undesired results if the
network connection speed does not meet the
requirements of the content being accessed.
yy
Some internet connection operations may not
be possible due to certain restrictions set by
the Internet service provider (ISP) supplying
your Internet connection.
yy
Any fees charged by an ISP including, without
limitation, connection charges are your responsibility.
yy
A 10 Base-T or 100 Base-TX LAN port is
required when using a wired connection to this
display. If your internet service does not allow
for such a connection, you will not be able to
connect the display.
Network Status
1Press SETTINGS to access the main menus.
2 Press the navigation buttons to scroll to
NETWORK and press OK.
3 Press the navigation buttons to select
Network Status.
4Press OK to check the network status.
5 When you are finished, press EXIT.
Option
Setting
Test
Close
Description
Return to the network setting menu.
Test the current network status after setting the network.
Return to the previous menu.
ENTERTAINMENT
Connecting USB Storage Devices
Tips for Using USB Storage Devices
yy
Only a USB storage device is recognizable.
yy
If the USB storage device is connected
through a USB hub, the device is not recognizable.
yy
A USB storage device using an automatic
recognition programme may not be recognized.
yy
A USB storage device which uses its own
driver may not be recognized.
yy
The recognition speed of a USB storage
or
device may depend on each device.
yy
Please do not turn off the display or unplug
the USB device when the connected USB
storage device is working. When such device
is suddenly separated or unplugged, the
stored files or the USB storage device may
be damaged.
yy
Please do not connect the USB storage
device which was artificially maneuvered on
the PC. The device may cause the product to
malfunction or fail to be played. Never forget
to use only a USB storage device which has
normal music files, image files or movie files.
yy
Please use only a USB storage device which
CAUTION
yy
Do not turn the display off or remove a USB
storage device while EMF (my media) Menu
is activated, as this could result in loss of
files or damage to the USB storage device.
yy
Back up your files saved on a USB storage
device frequently, as you may lose or damage the files and this may be not covered by
the warranty.
was formatted as a FAT32 file system, NTFS
file system provided with the Windows operating system. In case of a storage device
formatted as a different utility program which
is not supported by Windows, it may not be
recognized.
yy
Please connect power to a USB storage device (over 0.5 A) which requires an external
power supply. If not, the device may not be
recognized.
yy
Please connect a USB storage device with
the cable offered by the device maker.
yy
Some USB storage devices may not be supported or operated smoothly.
yy
File alignment method of USB storage
device is similar to Window XP and filename
can recognize up to 100 English characters.
ENG
ENGLISH
Connect USB storage devices such as a USB
flash memory, external hard drive to the display
and use multimedia features.
Connect a USB flash memory or USB memory
card reader to the Display as shown on the following illustration. The My media screen appears.
27
28
ENTERTAINMENT
yy
Be sure to back up important files since data
ENGLISH
ENG
stored in a USB memory device may be
damaged. We will not be responsible for any
data loss.
yy
If the USB HDD does not have an external
power source, the USB device may not be
detected. So be sure to connect the external
power source.
- Please use a power adaptor for an external
power source. We do not guarantee an USB
cable for an external power source.
yy
If your USB memory device has multiple
partitions, or if you use a USB multi-card
reader, you can use up to 4 partitions or USB
Browsing Files
Access the photo, music, or movie lists and browse
files.
1 Connect a USB storage device.
2 Press SETTINGS to access the main menus.
3 Press the navigation buttons to scroll to My
Media and press OK.
4 Press the Navigation buttons to choose
from Movie List, Photo List, Music List or
Contents List and press OK. (The function of
Contents List may not be supported depending
on the model.)
memory devices.
yy
If a USB memory device is connected to a
Movie List
USB multi-card reader, its volume data may
Photo List
not be detected.
Contents List
2
1
yy
If the USB memory device does not work
properly, disconnect and reconnect it.
Music List
Page 1/1
Photo List
USB External
Drive1
Page 1/1
4
yy
How fast a USB memory device is detected
001
differs from device to device.
yy
If the USB is connected in Standby Mode,
002
010
011
003
004
005
006
012
013
014
015
007
008
009
5
specific hard disk will automatically be
loaded when the display is turned on.
yy
The recommended capacity is 1 TB or less
Move
To Music List
for a USB external hard disk and 32 GB or
Change Numbers
View
Mark Mode
P
Page Change
Exit
3
less for USB memory.
yy
Any device with more than the recommended
capacity may not work properly.
yy
If a USB external hard disk with a “Energy
Saving” function does not work, turn the
hard disk off and on again to make it work
properly.
yy
USB storage devices below USB 2.0 are
supported as well. But they may not work
properly in the movie list.
yy
Maximum of 999 folders or files can be recognized under one folder.
yy
A USB 3.0 storage device may not work.
yy
Data on some USB storage devices may be
damaged in a high temperature environment.
No.
Description
1
Moves to upper level folder
2
Current page/Total pages
3
Corresponding buttons on the
remote control
4
Current page/ total pages of contents under
the folder focused on 1
5
Contents under the folder focused on 1
Button
Description
Green
button
Press the green button to toggle between
Photo List -> Music List, Music List ->
Contents List, Contents List -> Movie List
or Movie List -> Photo List.
Yellow
button
A method to view in 5 large thumbnail or
simple list.
Blue
button
Convert to Mark Mode.
ENTERTAINMENT
29
Supported File Format
Supported file format
DAT,MPG,MPEG,VOB,AVI,DIVX,MP4,MKV,TS,
TRP,TP,ASF,WMV,FLV)
Movie(*.mpg/*.mpeg/*dat/*.ts/*.trp/*.tp/*.vob/
*.mp4/*.mov/*.mkv/*.divx/*.avi/*.asf/*.wmv/*.flv/
*.avi(motion-jpeg)/*.mp4(motion-jpeg)/
*.mkv(motion-jpeg))supporting file
Video format : DivX 3.11, DivX4, DivX5, DivX6
Xvid1.00, Xvid1.01, Xvid1.02, Xvid1.03, Xvid1.10
beta-1/beta-2,
Mpeg-1, Mpeg-2, Mpeg-4, H.264/AVC, VC1,
JPEG, Sorenson H.263
Audio format : Dolby Digital, AAC, Mpeg, MP3,
LPCM, HE-AAC, ADPCM, WMA
Bit rate : within 32 kbps to 320 kbps(MP3)
External Subtitle format : *.smi/*.srt/*.sub(Micro
DVD,Subviewer1.0/2.0)/*.ass/*.ssa/
*.txt(TMPlayer)/*.psb(PowerDivX)
Photo
Internal Subtitle format : only, XSUB (It is the
subtitle format used in DivX6 files)
JPEG
Baseline : 64 x 64 to 15360 x 8640
Progressive : 64 x 64 to 1920 x 1440
yy You can play JPEG files only.
yy Non-supported files are displayed in the form
of predefined icon.
File
Item
Profile
Extensions
jpeg
jpg
jpe
supported
file format
photo size
SOF0: baseline
SOF1: Extend
Sequential
SOF2:
Progressive
Min: 64 x 64
Max-Normal
Type:
15360 (W) x
8640 (H)
Progressive
Type:
1920 (W) x 1440
(H)
Music
MP3
Bit rate 32 to 320
yy Sampling rate MPEG1 Layer3 : 32 kHz, 44.1
kHz, 48 kHz
yy Sampling rate MPEG2 Layer3 : 16 kHz, 22.05
kHz, 24 kHz
yy Sampling rate MPEG2.5 Layer3 : 8 kHz,
11.025 kHz, 12 kHz
ENG
ENGLISH
Type
Movie
30
ENTERTAINMENT
ENGLISH
ENG
Viewing Movies
5Play a movie.
Play video files on display. Your display shows all
of the video files saved in a USB storage device or
shared folder on a PC.
6 Control playback by using the following buttons.
1 Press the navigation buttons to scroll to My
Media and press OK.
2 Press the navigation buttons to scroll to Movie
01:02:30 / 02:30:25
List and press OK.
MENU
Option
Hide
Exit
3 Press the navigation buttons to scroll to a
folder you want and press OK.
4 Press the navigation buttons to scroll to a file
Button
you want and press OK.
Description
Stops the playback
Plays a video
Pauses or resumes the playback
Page 1/1
Movie List
Scans backward in a file
Drive1
USB1 USB Drive
001
002
005
006
Scans forward in a file
Page 1/1
003
SETTINGS
004
BACK
EXIT
Move
To Photo list
Change Numbers
Movie List
Mark Mode
Page Change
or
Drive1
001
002
005
006
Page 1/1
003
004
051. Apple_ ......
02:30:25
Move
Menu
P
Exit
Page 1/1
USB1 USB Drive
Play Marked
Play
Mark Mode
Mark All
Unmark All
Mark
Exit Mark Mode
P
Page Change
Exit
Description
Play Marked
Play the selected movie file.
Once a movie file finishes playing,
the next selected one will be played
automatically.
Mark All
Mark all movie files on the screen.
Unmark All
Deselect all marked movie files.
Exit Mark
Mode
Exit the Mark Mode.
ENERGY
SAVING
Show the Option menu.
Hide the menu on the full-sized screen.
Return to Movie List.
Skips to specific points in a file during playback. The time of a specific
point will appear on the status bar. In
some files, this function may not work
properly.
Reduces power consumption by adjusting peak screen brightness.
ENTERTAINMENT
Tips for Using Playing Video Files
Video Options
1 Press SETTINGS to access the Pop-Up
menus.
2 Press the navigation buttons to scroll to Set
Video Play. or Set Video. and press OK.
NOTE
yy
Option values changed in Movie List does
not affect Photo List and Music List.
yy
Option value changed in Photo List and Music List are changed likewise in Photo List
and Music List excluding Movie List.
yy
When replaying the video file after stopping,
you can play from where it stopped previously.
ENG
ENGLISH
yy
Some user-created subtitles may not work
properly.
yy
Some special characters are not supported
in subtitles.
yy
HTML tags are not supported in subtitles.
yy
Subtitles in languages other than the supported languages are not available.
yy
The screen may suffer temporary interruptions (image stoppage, faster playback, etc.)
when the audio language is changed.
yy
A damaged movie file may not be played
correctly, or some player functions may not
be usable.
yy
Movie files produced with some encoders
may not be played correctly.
yy
If the video and audio structure of recorded
file is not interleaved, either video or audio is
outputted.
yy
Videos with resolutions higher than
1920X1080@25/30p may not work properly
depending on the frame.
yy
Movie files other than the specified types and
formats may not work properly.
yy
Max bitrate of playable movie file is 20 Mbps.
(only, Motion JPEG : 10 Mbps)
yy
We do not guarantee smooth playback of
profiles encoded level 4.1 or higher in H.264/
AVC.
yy
DTS Audio codec is not supported.
yy
A movie file more than 30 GB in file size is
not supported for playback.
yy
A DivX movie file and its subtitle file must be
located in the same folder.
yy
A video file name and its subtitle file name
must be identical for it to be displayed.
yy
Playing a video via a USB connection that
doesn’t support high speed may not work
properly.
yy
Files encoded with GMC(Global Motion
Compensation) may not be played.
31
32
ENTERTAINMENT
When you select the Set Video Play,
ENGLISH
ENG
1 Press the navigation buttons to scroll to show
Code Page
Latin1
German, Italian, Portuguese,
the Picture Size, Audio Language, Subtitle
Language, or Repeat.
2 Press the navigation buttons to scroll to make
appropriate adjustments.
Support Language
English, Spanish, French,
Danish, Romanian, Norwegian,
Albanian, Gaelic, Welsh, Irish,
Catalan,Valencian
Bosnian, Polish, Croatian, Czech,
Latin2
Slovak, Slovenian, Serbian,
Latin4
Hungarian
Estonian, Latvian, Lithuanian
Cyrillic
Bulgarian, Macedonian, Russian,
Menu
Picture Size
Description
Selects your desired picture
Greek
Ukrainian, Kazakh
Greek
Turkish
Turkish
Audio
format during movie play.
Changes the Language Group of the
Korean
Korean
Language
audio during movie play. Files with a
Subtitle
single audio track cannot be selected.
Turn on/off the subtitle.
Language
Language
Activated for SMI subtitle and
can select the language within the
Code Page
subtitle.
Can select the font for subtitle.
When set to default, same font as
general menu will be used.
Sync
Adjusts the time synchronisation of
the subtitle from -10 secs to +10 secs
by steps of 0.5 secs during movie
play.
Position
Changes the position of the
subtitle either up or down during
movie play.
Size
Selects your desired Subtitle size
Repeat
during movie play.
Turn on/off repeat function of movie
NOTE
yy
Only 10,000 of sync blocks can be supported
within the subtitle file.
yy
When playing a video, you can adjust the
Picture Size by pressing the ARC button.
yy
Subtitles in your language are only supported when the OSD menu is also in this
language.
yy
The code page options may be disabled depending on the language of the subtitle files.
yy
Select the appropriate code page for the
subtitle files.
playback. When turned on, the file
within the folder will be played back
repeatedly. Even when the repeated
playback is turned off, it can run the
playback if the file name is similar to
the previous file.
For more details about the Set Video. menu, see
the CUSTOMIZE SETTINGS section. See p.42
ENTERTAINMENT
33
Viewing Photos
1 Press the navigation buttons to scroll to My
Media and press OK.
2 Press the navigation buttons to scroll to Photo
List and press OK.
3 Press the navigation buttons to scroll to a
folder you want and press OK.
4 Press the navigation buttons to scroll to a file
you want and press OK.
Page 1/1
Photo List
USB1 USB Drive
001
Drive1
002
010
011
Page 1/1
003
004
005
006
012
013
014
015
View
Move
Change Numbers
To Music List
008
007
009
P
Page Change
Exit
Mark Mode
Page 1/1
Photo List
Mark Mode
USB1 USB Drive
001
010
Drive1
002
011
Page 1/1
003
004
005
006
012
013
014
015
Mark
Move
View Marked
Mark All
Menu
Unmark All
008
007
Exit Mark Mode
009
P
Page Change
Exit
Description
View Marked
Display the selected photo file.
Mark All
Mark all photo files on the screen.
Unmark All
Deselect all marked photo files.
Exit Mark Mode Exit the Mark Mode.
5 View photos.
ENG
ENGLISH
View image files saved in a USB storage device.
The displays on the screen may differ from the
model.
34
ENTERTAINMENT
Using Photo Options
ENGLISH
ENG
Use the following options while viewing photos.
Option
ENERGY
SAVING
Description
Reduces power consumption by adjusting peak screen brightness.
yy Slide Speed: Selects a slideshow
speed (Fast, Medium, Slow).
yy TransitionEffect: Set the view mode
of the slideshow.
yy BGM: Selects a music folder for the
background music.
NOTE
yyYou cannot change the music
folder while the background
music is playing.
yyYou can only select the MP3
folder saved on the device that
currently displays the photo.
2/13
Slideshow
BGM
Options
Option
Slideshow
BGM
MENU
Option
Hide
Exit
Number of selected photos
Description
Starts or stops a slideshow with selected
photos.
If there are no selected photos, all photos saved in the current folder display
during a slideshow.
To set a slideshow speed, select Option.
Turns the background music on or off.
To set the background music folder,
select Option.
You can adjust Option by SETTINGS
button on the remote control.
Hides the option window.
To display the options, press OK.
Return to Photo List.
Photo options
1 Press SETTINGS to show the Option menus.
2 Press the navigation buttons to scroll to Set
Photo View. or Set Video. and press OK.
Rotates photos clockwise (90°, 180°,
270°, 360°).
NOTE
yyThe supported photo size is
limited. You cannot rotate a
photo if the resolution of the
rotated width is larger than the
supported resolution size.
View the photo by zoom in 2, 4 times.
NOTE
yyPhotos with a resolution of
960x540 or less cannot be
enlarged.
NOTE
yy
Option values changed in Movie List does
not affect Photo List and Music List.
yy
Option value changed in Photo List and Music List are changed likewise in Photo List
and Music List excluding Movie List.
ENTERTAINMENT
35
When you select the Set Photo View,
2 Press the navigation buttons to scroll to make appropriate adjustments.
Transition Effect Option
Option
Description
Sliding
The current photo disappears horizontally, vertically or diagonally and the next photo appears.
Stairs
The next photo appears and overlaps with the current photo in a staircase shape.
Door Open
/Close
The current photo disappears as though a door opens and closes, and the next photo appears.
Shutter
The current photo disappears as though drawing or pulling down a blind and the next photo appears slowly.
Fade In
The current photo disappears and the next photo appears slowly.
For more details about the Set Video. menu, see the CUSTOMIZE SETTINGS section. See p.42
ENG
ENGLISH
1 Press the navigation buttons to scroll to select Slide Speed,Transition Effect or BGM.
36
ENTERTAINMENT
Listening to Music
6 Control playback by using the following buttons.
ENGLISH
ENG
1 Press the navigation buttons to scroll to My Me-
Page 1/1
Music List
3 file(s) Marked
Drive1
Page 1/1
dia and press OK.
2 Press the navigation buttons to scroll to Music
List and press OK.
004. - B04.mp3
00:00
005. - B05.mp3
00:00
006. - B06.mp3
00:00
007. - B07.mp3
00:00
005. - B05.mp3
02:30 / 03:25
Play with Photo
3 Press the navigation buttons to scroll to a folder
008. - B08.mp3
00:00
MENU
Option
Hide
Exit
you want and press OK.
4 Press the navigation buttons to scroll to a file
you want and press OK.
Button
Description
Stops playing back the file and moves
back to the music list.
Plays a music file.
Page 1/1
Music List
USB1 USB Drive
Pauses or resumes playback.
Drive1
001. - B01.mp3
00:00
Page 1/1
002. -B02.mp3
00:00
003. B03.mp3
00:00
Skips to the previous file.
004. - B04.mp3
00:00
Skips to the next file.
005. - B05.mp3
00:00
Play
Move
Change Numbers
To Movie List
P
Page Change
Exit
Mark Mode
Green
button
ENERGY
SAVING
Page 1/1
Music List
Mark Mode
USB1 USB Drive
Drive1
001. - B01.mp3
00:00
Page 1/1
002. -B02.mp3
00:00
003. B03.mp3
00:00
004. - B04.mp3
00:00
005. - B05.mp3
00:00
Move
Play Marked
Menu
Mark All
Unmark All
Mark
P
Page Change
Exit Mark Mode
Exit
Description
Play Marked
Display the selected music file.
Mark All
Mark all music files on the screen.
Unmark All
Deselect all marked music files.
Exit Mark Mode Exit the Mark Mode.
5 Play music.
◄ or ►
Start playing the selected music files and
then move to the Photo List.
Reduces power consumption by adjusting peak screen brightness.
Show the Option menu.
Hides the option window.
To display the options, press OK.
When you press the EXIT button while
the Music player is displayed, only the
music will be stopped and the player will
not return to normal viewing.
When you press the EXIT button while
the music is stopped or while the music
player is hidden, the player will return to
normal viewing.
Skips to specific points in a file during playback. The time of a specific
point will appear on the status bar. In
some files, this function may not work
properly.
ENTERTAINMENT
Tips for playing music files
Music Options
1 Press SETTINGS to access the Pop-Up menus.
2 Press the navigation buttons to scroll to Set Au-
NOTE
dio Play and press OK.
yy
A damaged or corrupted music does not play
but displays 00:00 in playtime.
yy
A music downloaded from a paid service with
copyright protection does not start but displays inappropriate information in playtime.
yy
If you press OK,
buttons, screen saver is
stopped.
yy
The
,
,
,
,
buttons on the remote control are also available in this mode.
yy
You can use the
button to select the next
music and the
button to select the previous music.
NOTE
yy
Option values changed in Movie List does
not affect Photo List and Music List.
yy
Option value changed in Photo List and Music List are changed likewise in Photo List
and Music List excluding Movie List.
When you select the Set Audio Play,
1 Press the navigation buttons to scroll to select
the Repeat or Random.
file name
002. B02.mp3
00:31 / 04:04
Time elapsed /Duration
2 Press the navigation buttons to scroll to make
appropriate adjustments.
ENG
ENGLISH
This unit cannot support the ID3 Tag
yy
embedded MP3 files.
37
38
ENTERTAINMENT
Viewing the Contents List
ENGLISH
ENG
Plays back the stored files using the Export option
in SuperSign Manager.
1 Press the Navigation buttons to scroll to My
Media and press OK.
2 Press the Navigation buttons to scroll to Contents List and press OK.
3 Press the Navigation buttons to scroll to a
folder you want and press OK.
4 Press the Navigation buttons to scroll to a file
you want and press OK.
Page 1/1
Contents List
USB1 USB Drive
test1.cts
07/01/2011
Drive1
Page 1/1
test2.cts
07/01/2011
test3.cts
07/01/2011
test4.cts
07/01/2011
test5.cts
07/01/2011
Move
To Movie List
Change Numbers
Play
P
Page Change
Exit
NOTE
yy
While playing media files from Contents List,
only the BACK, EXIT or Volume button are
available. Selecting the BACK or EXIT button
stops playing media files and returns to the
screen view mode.
yy
If there is the AutoPlay folder in the USB
device and its files are in supported formats,
they can be played back automatically when
the USB device is connected to the monitor.
yy
The function of Contents List may not be
supported depending on the model.
ENTERTAINMENT
DivX® VOD Guide
In order to play purchased or rented DivX® VOD
contents, you should register your device with 10
digit DivX registration code from your device at
www.divx.com/vod.
DivX® VOD Deregistration
You should deregister your device with 8 digit DivX
deregistration code from your device at
www.divx.com/vod.
1Press SETTINGS to access the main menus.
2 Press the navigation buttons to scroll to MY MEDIA and press OK.
1Press SETTINGS to access the main menus.
3 Press the Blue button.
2 Press the navigation buttons to scroll to MY ME-
4 Press the navigation buttons to scroll to Deacti-
3 Press the Blue button.
5 Press the navigation buttons to select Yes to
DIA and press OK.
4 Press the navigation buttons to scroll to DivX
vation and press OK.
confirm.
Reg. Code and press OK.
Deregistration code :
********
Deregister at http://vod.divx.com
Continue with registration?
5 View the registration code of your display.
6 When you are finished, press EXIT.
When you return to the previous menu, press
BACK.
You must register your device to
play DivX protected videos.
Registration code : **********
Register at http://vod.divx.com
Yes
No
6 When you are finished, press EXIT.
When you return to the previous menu, press
BACK.
Close
NOTE
yy
While you are checking the registration
code, some buttons may not work.
yy
If you use the DivX registration code of
another device, you cannot play the rented
or purchased DivX file. Make sure to use
the DivX registration code assigned to your
product.
yy
The video or audio files that are not converted by the standard DivX codec may be
corrupted or not be played.
yy
The DivX VOD code allows you to activate
up to 6 devices under one account.
NOTE
Once the deregistration is executed, you
yy
must register your device again to see DivX®
VOD contents.
ENG
ENGLISH
DivX® VOD Registration
39
40
ENTERTAINMENT
Using PIP/PBP
5Select the PIP or PBP icon from the play list.
ENGLISH
ENG
Displays videos or photos stored on a USB device
on a single monitor by dividing it into the main and
sub screens.
1Press the SETTINGS button to move to
OPTION and press OK.
2 Press PIP/PBP to select PIP or PBP and then
01:02:30 / 02:30:25
press OK.
MENU
Exit
Hide
Option
< Movie List >
PIP/PBP
Mode
Move
Pre.
Off
Position
PIP
Size
PBP
3Select Movie List or Photo List from My
Media. (With PIP/PBP selected, the Music
List and Contents List are deactivated. The
function of Contents List may not be supported
depending on the model.)
2/13
Slideshow
MENU
BGM
Option
Hide
Exit
< Photo List >
Movie List
Photo List
Music List
6Select either Main or Sub for sound. You must
Contents List
4 Select a file you want and then press OK.
to select the output sound before running the
PIP or PBP function.
Page 1/1
Movie List
Select the sound path.
Drive1
USB1 USB Drive
001
002
005
006
Page 1/1
003
Main
004
Sub
7The sub screen is displayed on the main
screen.
Move
To Photo list
Change Numbers
Mark Mode
Play
P
Exit
Page Change
CUSTOMIZING SETTINGS
ENG
ENGLISH
CUSTOMIZING SETTINGS
Accessing the Main Menus
1Press SETTINGS to access the main menus.
2 Press the navigation buttons to scroll to one of the following menus and
press OK.
3 Press the navigation buttons to scroll to the setting or option you want
and press OK.
4 When you are finished, press EXIT.
When you return to the previous menu, press BACK.
PICTURE
Adjusts the image size,
quality, or effect.
PICTURE
OPTION
Sets the functions of
OPTION.
OPTION
AUDIO
Sets the functions of
AUDIO.
AUDIO
NETWORK
NETWORK
Sets the functions of
NETWORK.
41
TIME
MY MEDIA
TIME
Sets the time, date, or
timer feature.
MY MEDIA
Display and play movie,
photo and music content
stored on your USB.
42
CUSTOMIZING SETTINGS
PICTURE Settings
PICTURE
ENGLISH
ENG
1Press SETTINGS to access the main menus.
2 Press the navigation buttons to scroll to PICTURE and
press OK.
Move
• Aspect Ratio
: 16:9
•
Energy Saving : Off
• Easy Brightness Control : Off
• Smart Energy Saving
: Off
OK
ꔋ
• Picture Mode : Standard
• Backlight 70
• Contrast option you want and press OK.
• Brightness 50
-To return to the previous level, press BACK.
• Sharpness 50
• Color • Tint 0
R
G
• Color Temp. 0
W
C
• Advanced Control
• Picture Reset
• TruMotion
: Low
3 Press the navigation buttons to scroll to the setting or
4 When you are finished, press EXIT.
When you return to the previous menu, press
BACK.
100
60
• Screen
The available picture settings are described in the following:
Setting
Aspect Ratio
Description
Changes the image size to view images at its optimal size.
Reduces power consumption by adjusting peak screen brightness.
Energy Saving Level
Easy
Brightness
Control
Off
Disables Energy Saving function.
Minimum/
Medium/
Maximum
Selects the brightness level of the backlight.
Screen Off
The screen turns off in 3 seconds.
Adjusts the backlight according to the schedule you set.
Mode
Off
Disables Easy Brightness Control.
On
Enables Easy Brightness Control.
NOTE
yyEasy Brightness Control is disabled if the current time is not set.
yyIf Energy Saving is set to Maximum, Easy Brightness Control is disabled.
yyYou can set up to six schedules and they will be sorted in time ascending order.
yyIf more than six schedules are added, the latest schedule will be automatically deleted.
yyYou can delete a schedule by pressing the OK button.
yyDuplicate schedules are not added, but the backlight value changes.
yyIt may not be supported depending on the model.
Smart Energy
Saving
Picture Mode
Adjusts the backlight and contrast depending on the screen brightness.
Level
Off
Disables the Smart Energy Saving function.
On
Enables the Smart Energy Saving function to save power consumption as much
as the value set in the smart energy saving rate.
Selects one of the preset image or customizes options in each mode for the best Monitor set screen
performance. You are also able to customize advanced options of each mode. The available preset
picture modes vary depending on the monitor set .
43
CUSTOMIZING SETTINGS
Setting
SCREEN
(In RGB
Mode Only)
Description
Corrects images to display smoother motion sequences.
TruMotion
• Low : De-Judder / De-Blur value is set to 3.
• High : De-Judder / De-Blur value is set to 7.
• De-Judder
• User : De-Judder / De-Blur can be set manually.
• De-Blur
-D
e-Judder : This function adjusts juddering of
the screen.
- De-Blur : This function adjusts and eliminates blurring of the screen.
◄
Low
►
3
3
OK
Customizes the PC display options in RGB mode.
Option
Resolution
Selects a proper resolution. See “Customizing PC display options”.
Auto Configure
Sets to adjust the screen position, clock, and phase automatically.
The displayed image may be unstable for a few seconds while the configuration is
in progress.
Position/Size/
Phase
Adjusts the options when the picture is not clear, especially when characters are
shaky, after the auto configuration.
Reset
Restores the options to the default setting.
Basic Image Options
Setting
Description
Backlight
djusts the brightness of the screen by controlling the LCD backlight. If you decrease the
A
brightness level, the screen becomes darker and the power consumption will be reduced
without any video signal loss.
Contrast
Increases or decreases the gradient of the video signal. You may use Contrast when the
bright part of the picture is saturated.
Brightness
Adjusts the base level of the signal in the picture. You may use Brightness when the dark part
of the picture is saturated.
Sharpness
Adjusts the level of crispness in the edges between the light and dark areas of the picture.
The lower the level, the softer the image.
Color
Adjusts intensity of all colors.
Tint
Adjusts the balance between red and green levels.
Color Temp .
Set to warm to enhance hotter Colors such as red, or set to cool to make picture bluish.
Advanced Control
Customizes the advanced options. Refer to the Advanced image options.
Picture Reset
Restores the options to the default setting.
NOTE
If the 'Picture Mode' setting in the Picture menu is set to Vivid, Standard, Cinema, Sport, or Game
yy
the subsequent menus will be automatically set.
You cannot adjust Sharpness, Color and Tint in the RGB/ HDMI-PC/ DVI-PC mode.
yy
When using the Smart Energy Saving function, the screen may look saturated in the white area of a
yy
still image.
If Energy Saving is set to Minimum, Medium, or Maximum, the Smart Energy Saving function is
yy
disabled.
In Vivid mode, the luminance of the backlight is calibrated, so the settings may be different depending
yy
on each product.
ENG
ENGLISH
TruMotion
44
CUSTOMIZING SETTINGS
Advanced Control
ENGLISH
ENG
Setting
Dynamic
Contrast
(Off/High/
Medium/Low)
Description
Adjusts the contrast to keep it at the best level according to the brightness of the screen. The
picture is improved by making bright parts brighter and dark parts darker. (Function works in the
following mode - AV(CVBS), Component, DP, HDMI, DVI)
Dynamic Color Adjusts screen Colors so that they look livelier, richer and clearer. This feature enhances
(Off/High/Low) hue, saturation and luminance so that red, blue, green and white look more vivid. (Function works in
the following mode - AV(CVBS), Component, DP, HDMI, DVI)
Clear White
(Off/High/Low)
Make the white area of screen brighter and more white.
Skin Color
(-5 to 5)
It detects the skin area of video and adjusts it to express a natural skin color.
Noise
Reduction
(Off/High/
Medium/Low)
Reduces screen noise without compromising video quality. (Function works in the following mode AV(CVBS), Component, DP, HDMI, DVI)
Digital Noise
Reduction
(Off/High/
Medium/Low)
This option reduces the noise produced while creating digital video signals.
Gamma
(High/Medium/
Low)
Set your own gamma value. On the monitor, high gamma values display whitish images and low
gamma values display high contrast images.
Black Level
(High/Low)
Low: The picture of the screen gets darker.
High: The picture of the screen gets brighter.
Set black level of the screen to proper level.
(Function works in the following mode - AV(CVBS), Component, DP, HDMI, DVI)
CUSTOMIZING SETTINGS
AUDIO Settings
AUDIO
1Press SETTINGS to access the main menus.
Move
: Off
• Digital Audio Input : Audio In
2 Press the navigation buttons to scroll to AUDIO and press
OK.
3 Press the navigation buttons to scroll to the setting or
option you want and press OK.
-To return to the previous level, press BACK.
4 When you are finished, press EXIT.
When you return to the previous menu, press BACK.
The available audio options are described in the following:
Setting
Description
Mute
Sets the audio output to mute.
Digital Audio
Input
This function is available in HDMI or DisplayPort inputs.
HDMI/DisplayPort: Listen to digital audio through the monitor speakers.
Audio In: Listen to audio from an external device through the monitor speakers.
OK
ꔋ
ENG
ENGLISH
• Mute
45
46
CUSTOMIZING SETTINGS
TIME Settings
TIME
Move
ENGLISH
ENG
• Clock
1Press SETTINGS to access the main menus.
2 Press the navigation buttons to scroll to TIME and press OK.
3 Press the navigation buttons to scroll to the setting or option
you want and press OK.
-To return to the previous level, press BACK.
OK
ꔋ
• Daylight Saving : Off
• Off Time : Off
• On Time : Off
• Screen Off Time : Off
• Sleep Timer : Off
• Power On Delay : Off
• Auto Off
: 15 min.
• Automatic Standby: 4hours
4 When you are finished, press EXIT.
When you return to the previous menu, press BACK.
The available time settings are described in the following:
Setting
Description
Clock
Sets the time feature.
Daylight Saving
Sets the current time one hour ahead of Standard Time in the summer season.
On/Off Time
Sets the time to turn on or off the monitor set.
Screen Off Time
Sets the time to turn off the screen.
Sleep Timer
Sets the length of time until the monitor set to turns off. When you turn the monitor set off and turn
it on again, the Sleep Timer will be set to off.
Power on delay
When connecting multiple monitors and turning the power on, the monitors are turned on individually
to prevent overload.
Auto off
If Auto off is active and there is no input signal, the set switches to off mode automatically after 15
minutes.
Automatic
Standby
If you do not use the monitor for more than 4 hours, it will be in standby mode automatically.
NOTE
Once the on or off time is set, these functions operate daily at the preset time.
yy
The scheduled power-off function works properly only when the device time is set correctly.
yy
When the scheduled power-on and power-off times are the same, the power-off time has priority over
yy
the power-on time if the set is turned on, and vice versa if the set is turned off.
CUSTOMIZING SETTINGS
OPTION Settings
OPTION
Move
1Press SETTINGS to access the main menus.
2 Press the navigation buttons to scroll to OPTION and press
OK.
OK
ꔋ
• ISM Method : Normal
• DPM Select
: On
• Fail Over
: Off
• Factory Reset
3 Press the navigation buttons to scroll to the setting or option
you want and press OK.
• Set ID
:1
• Tile Mode
• PIP/PBP
• Fan
-To return to the previous level, press BACK.
• USB Content Recovery : Off
4 When you are finished, press EXIT.
• SIMPLINK
• Product/Service Info.
When you return to the previous menu, press BACK.
The available option settings are described in the following:
Setting
Description
Language
To choose the language in which the control names are displayed.
ISM Method
A frozen or still picture from a PC/Video game displayed on the screen for prolonged periods
could result in a ghost image remaining even when you change the image. Avoid allowing a fixed
image to remain on the screen for a long period of time.
Setting
DPM Select
Normal
Leave on normal if you don't foresee image burn in being a problem.
Orbiter
May help prevent ghost images. However, it is best not to allow any fixed
image to remain on the screen. To avoid a permanent image on the screen,
the screen will move every 2 minutes.
Inversion
This function inverts the panel color of the screen. The panel color is
automatically inverted every 30 minutes.
White Wash
White wash fills the screen with solid white. This helps removes permanent
images burned into the screen. A permanent image may be impossible to clear
entirely with white wash.
A user can choose to turn the power saving mode on / off.
NOTE
yyYou can set Energy Saving to Off or set the length of time before entering Energy Saving
mode to 5 sec./10 sec./15 sec./1 min./3 min./5 min./10 min.
yyIt makes a little difference according to your environment.
yyIt may not be supported depending on the model.
Fail Over
If there is no input signal, it automatically switches to another input with signal.
Setting
Off
Stops auto switch of the input source.
Auto
Attempts to find another input source having video signal according to the
defined input order if no video signal comes from the current input source.
(Refer to the sequence of the table below.)
Current
Input Source
Attempt 1
Attempt 2
Attempt 3
Attempt 4
RGB
HDMI
DVI
DP
If there is no
available video
signal to switch to,
then the current
input source
remains.
DVI
HDMI
DP
RGB
HDMI
DVI
DP
RGB
DP
HDMI
DVI
RGB
Manual
Factory Reset
The input source changes according to the specified order.
If there is no video signal from the specified input source, then the current
input source remains.
Select this option to return to the default factory settings.
ENG
ENGLISH
• Language
47
48
CUSTOMIZING SETTINGS
Setting
Description
ENGLISH
ENG
Set ID
You can assign a unique Set ID NO (name assignment) to each product when several products
are connected for display. Specify the number (1 - 255, 1 - 1,000 in certain models) using the
button and exit. Use the assigned Set ID to individually control each product using the Product
Control Program.
Tile Mode
Tile Mode
To use this function
- Must be displayed with various other products.
- Select Tile Mode, set rows and columns, and then enter the tile ID to set the
location.
- Tile Mode: row x column (row = 1-15, column = 1-15).
- 15 x 15 available.
Auto Config.
Sets to adjust the screen position, clock, and phase automatically.
The displayed image may be unstable for a few seconds while the
configuration is in progress.
Position
Moving the screen position horizontally and vertically.
Size
Adjust the horizontal and vertical size of the screen taking into account the size
of the bezel.
Natural
The image is omitted by the distance between the screens to be naturally
shown.
Reset
Function to initialize and release Tile.
All Tile setting are released when selecting Tile recall and the screen returns to
Full screen.
* Natural is not initialized.
PIP/PBP
Displays videos or photos stored in the USB device on a single monitor by dividing it into the main
and sub screens.
Option
Mode
Sets the type of secondary screen.
*OFF: Disables the secondary screen.
*PIP (Picture In Picture): Displays the secondary screen in the main screen.
*PBP (Picture By Picture): Displays the secondary screen next to the main
screen.
Position
Adjusts the position of the sub screen (top left, bottom left, top right, bottom
right)
The default value is the bottom right.
Size
Adjusts the size of the sub screen (Size 0 to 10).
The default size of PIP (Size: 0) is 480x270; the maximum size 10 is 960x540.
NOTE
yyThe Position and Size options are enabled only in PIP mode.
CUSTOMIZING SETTINGS
Setting
49
Description
This option indicates the monitor's internal temperature and controls the
fan.
• Auto: Switches the fan on and off according to the set temperature.
• On: The fan is always switched on.
• Manual: Switches the fan on and off according to user settings.
Hysteresis
The difference in temperature between when the fan is switched on and
when it is off.
Set Temperature
Set the temperature at which the fan is switched on.
Current Temperature
Current temperature inside the set.
NOTE
yyWe recommend that you use the Auto mode to prevent any malfunctions resulting from
incorrect fan settings.
yyIf the interior temperature of the set exceeds 80°C, the set will be turned off automatically
for safety reasons.
USB Content
Recovery
Replays the content in a USB when the power is back on if it is turned off during playing a content.
(This function operates the same when a USB is disconnected and connected again.)
SIMPLINK
Allows you to control various multimedia devices simply by using the remote control through the
SimpLink menu. (It may not be supported depending on the model.)
Product/Service
Info.
Displays the model name, software version, serial number, IP address, MAC address, and home
page.
ENG
ENGLISH
Fan
Setting
(Only for 55LV77A Mode
model)
50
CUSTOMIZING SETTINGS
Tile Mode
ENGLISH
ENG
This monitor can be tiled with additional monitors to create a large tiled display.
Off
When the Tile Mode
option is disabled
1X2
When using 2 monitors
ID 1
3X3
When using 9 monitors
2X2
When using 4 monitors
ID 2
ID 1
ID 2
ID 1
ID 2
ID 3
ID 3
ID 4
ID 4
ID 5
ID 6
ID 7
ID 8
ID 9
Tile ID
4X4
When using 16 monitors
5X5
When using 25 monitors
ID 1
ID 2
ID 3
ID 4
ID 1
ID 2
ID 3
ID 4
ID 5
ID 5
ID 6
ID 7
ID 8
ID 6
ID 7
ID 8
ID 9
ID 10
ID 9
ID 10
ID 11
ID 12
ID 11
ID 12
ID 13
ID 14
ID 15
ID 13
ID 14
ID 15
ID 16
ID 16
ID 17
ID 18
ID 19
ID 20
ID 21
ID 22
ID 23
ID 24
ID 25
Tile Mode - Natural mode
When active, the part of the image that would normally be displayed in the gap between the monitors is
omitted.
Before
After
CUSTOMIZING SETTINGS
PIP/PBP
NOTE
The subscreen is only supported when using
yy
the USB device.
Sub
Mode
*PIP (Picture In Picture): Displays the sub screen
in the main screen.
*PBP (Picture By Picture): Displays the sub
screen next to the main screen.
Sub
Screen
Main
Screen
PIP
PBP
Position
Adjusts the position of the subscreen (top left,
bottom left, top right, bottom right)
top left
top right
bottom left
bottom right
USB
Main
Component
O
RGB
O
HDMI/DVI-D/Display Port
O
AV
X
You can only change the size and position in
yy
PIP mode.
With PBP selected, the Aspect Ratio option
yy
in the PICTURE menu is disabled (Fixed as
16:9).
While running the PIP/PBP function, the Tile
yy
Mode function does not work.
You must select the output sound before
yy
running the PIP or PBP functions. (Select
either main or sub.)
If you fail to select main or sub from the
yy
sound selection box, and if the OSD
disappears after either a period of time or
when the Exit or Back key is pressed, the
PIP/PBP subscreen is not activated.
You cannot change the sound while running
yy
the PIP or PBP functions. If you want to
change the sound, please restart PIP/PBP.
The picture quality of the subscreen is set
yy
according to the values selected in the main
menu, not the USB device.
If you play videos you selected in PIP/PBP
yy
mode, the videos will play back repeately in
succession.
The buttons below work in PIP mode.
yy
Button
◄
►
Size
Adjusts the size of the subscreen (Size 0-10).
PBP
960x1080
10 : 960x540
PIP
0:
480x270
< 1920x1080 >
Photo
Movie
ENG
ENGLISH
Displays videos or photos stored in the USB
device on a single monitor by dividing it into the
main and sub screens.
51
52
CUSTOMIZING SETTINGS
Picture ID
ENGLISH
ENG
Picture ID is used to change the settings of a
specific display using a single IR receiver for
multi-vision. The set receiving the IR signal
communicates with another set via an RS-232C
connection. Each set is identified by a Set ID. If
you assign the Picture ID using the remote control,
only displays with the same Picture ID and Set ID
can be controlled remotely.
2 To change the Picture ID, press the ON button,
or the left and right arrow buttons continuously.
Assign the ID you want.
Picture ID
◄
Off
►
Close
AUDIO
(RGB/DVI)
RS-232C OUT
RS-232C OUT
RS-232C OUT
RS-232C IN
RS-232C IN
RS-232C IN
REMOTE
CONTROL IN
IR Receiver
If you assign the Set ID to each set with
yy
multi-vision, and then assign the Picture ID
using the red button on the remote control,
the key command is displayed for the set
with the same Set ID and Picture ID. A set
with different Set IDs and Picture IDs cannot
be controlled by IR signals.
The maximum value of the Picture ID can be
yy
set in the Total Set ID menu.
Please refer to the Installation Manual for
yy
more information on Total Set ID assignment.
Picture ID
◄
Off
►
Close
NOTE
2X2 Multi-Vision (Total Set ID: 4)
Set IDs are assigned as shown in the picture.
1Press the red ON button on the remote control
to assign the Picture ID.
For example, if the Picture ID is assigned to
yy
2, the upper right display (Set ID: 2) can be
controlled by IR signals.
For each set, you can change the settings
yy
for the PICTURE, AUDIO, TIME, NETWORK
and MY MEDIA menus or the hot keys on the
remote control.
If you press the green OFF button for Picture
yy
IDs, the Picture IDs for all sets are turned off.
If you then press any button on the remote
control, all sets will start working again.
Picture ID will be disabled while using the
yy
MY MEDIA menu.
If Picture ID is set to Off, holding buttons
yy
on the remote control will execute only one
action at a time.
CUSTOMIZING SETTINGS
NETWORK Settings
NETWORK
Move
1Press SETTINGS to access the main menus.
2 Press the navigation buttons to scroll to NETWORK and
press OK.
• Network Setting
: None
• Network Status
: Not connected
• Server IP Setting
• Server IP Status
: Not connected
3 Press the navigation buttons to scroll to the setting or option
you want and press OK.
-To return to the previous level, press BACK.
4 When you are finished, press EXIT.
When you return to the previous menu, press BACK.
The available option settings are described in the following:
Setting
Description
Player Name
Setting
Sets the player name used in SuperSign Manager.(Up to 20 characters)
Network Setting
Configure the network settings.
Network Status
Display the network status.
- Internet is connected : Extermally connected
- Network is connected : Only internally connected
- Not connected : When there is no network connection
Server IP Setting
Sets the IP address of the computer (server) on which SuperSign Manager is installed.
Server IP Status
Displays the connection status with the server.
- Not connected : When there is no network connection with SuperSign server
- Waiting for approval : When network connection with SuperSign server has been made, but
access to server has not been approved by the server
- Rejected : When network connection with SuperSign server has been made, but access to
server has been rejected by the server
- Internet is connected : When network connection with SuperSign server has been made and
access to server has also been approved by the server
CAUTION
When setting the Player Name Setting, input delay may occur if you press the buttons on the remote
yy
control continuously.
OK
ꔋ
ENG
ENGLISH
• Player Name Setting
53
54
MAKING CONNECTIONS
MAKING CONNECTIONS
ENGLISH
ENG
Connect various external devices to the ports on the monitor set’s back panel.
1 Find an external device you want to connect to your monitor set shown on the following illustration.
2 Check the connection type of the external device.
3 Go to the appropriate illustration and check the connection details.
HD Receiver
HDMI
DVI
AV
Component
DVD
HDMI
DVI
AV
Component
Speaker
VCR
AV
Component
Memory storage
USB
PC
HDMI
DVI
RGB
LAN
Display Port
Camcorder/ Camera
HDMI
DVI
AV
Component
Gaming device
HDMI
AV
Component
NOTE
If you connect a gaming device to the monitor set, use the cable supplied with the gaming device.
yy
MAKING CONNECTIONS
55
HDMI Connection
Connect a HD receiver, DVD, or VCR player to the
monitor set and select an appropriate input mode.
Transmits the digital video and audio signals from
an external device to the monitor set. Connect the
external device and the monitor set with the HDMI
cable as shown on the following illustration.
DVI Connection
Back of the product.
Transmits the digital video signal from an external
device to the monitor set. Connect the external
device and the monitor set with the DVI cable as
shown in the following illustration. To transmit an
audio signal, connect an optional audio cable.
Back of the product.
(not included)
(not
included)
(not included)
External device
External device
NOTE
Use a High Speed HDMI®/TM Cable.
yy
High Speed HDMI®/TM Cables are tested to
yy
carry an HD signal up to 1080p and higher.
Use a certified cable with the HDMI logo
yy
attached. If you do not use a certified HDMI
cable, the screen may not display or a
connection error may occur.
Recommended HDMI cable types
yy
- High-Speed HDMI®/TM cable
- High-Speed HDMI®/TM cable with Ethernet
ENG
ENGLISH
External Device Connection
56
MAKING CONNECTIONS
ENGLISH
ENG
Component Connection
AV(CVBS) Connection
Transmits the analog video and audio signals from
an external device to the monitor set. Connect
the external device and the monitor set with the
RGB-Component cable as shown in the following
illustration.
Transmits the analog video and audio signals from
an external device to the monitor set. Connect
the external device and the monitor set with
the composite cable as shown in the following
illustration.
Back of the product.
(not included)
Back of the product.
(not included)
(not included)
AUDIO IN
External device
NOTE
When connecting to the component port
yy
using the shared interface, the port must
match up to the input source. Otherwise,
noise may occur.
VIDEO OUT
VIDEO OUT
AUDIO IN
External device
(not included)
MAKING CONNECTIONS
57
Connecting to the LAN
Audio Connection
ENG
ENGLISH
An analog/digital audio signal is sent from the
monitor to an external device.
Connect the external device to the monitor by
using the audio cable as shown in the following
illustration.
A Using a router (Switch)
LAN
Switch
Back of the product.
Monitor Set
PC
Network
B Using the Internet.
LAN
Network
(not included)
PC
Monitor Set
VIDEO OUT
AUDIO IN
External device
Connecting to a USB
Connect a USB storage device such as s USB
flash memory, external hard drive, MP3 player, or
a USB memory card reader to the monitor set and
access the USB menu to use various multimedia
files.
NOTE
When connecting an external audio device,
yy
use a device with audio amplifier.
or
58
MAKING CONNECTIONS
Daisy Chain Monitors
ENGLISH
ENG
To use different products connected to each other, connect one end of the signal input cable (DP Cable) to
the DP Out connector of Monitor 1 and connect the other end to the DP In connector of the other product.
DP Cable
Use the cable provided with the product or use a DisplayPort certified cable version 1.1a or higher.
Monitor 1
Monitor 2
Monitor 3
Monitor 4
NOTE
If the signal is stable and there is no cable loss, in general, up to 100 monitors can be connected via
yy
the DP Out port (at the recommended resolution). If you want to connect more than this number of
monitors, it is recommended to use a distributor.
If you set the tile mode using DVI or HDMI, you will not be able to watch HDCP-encrypted content.
yy
If the signal cable between the product and your PC is too long, make sure to use the Booster or
yy
optical cable.
TROUBLESHOOTING
59
Using the Multi Display Mode function
ENG
ENGLISH
The Multi Display Mode function displays a video signal received from DP In either in single mode (SST:
Single Stream Transport) or multi-mode (MST: Multi Stream Transport) through DP Out.
-- This function can be configured in the Installation Menu (For more information, refer to the
Installation Menu manual.)
-- If it is On, the image of each display is displayed in multi-mode.
-- If it is Off, the image of each display is displayed in single mode.
-- The multi-mode is available in a PC supporting DisplayPort 1.2.
-- Multi-mode can connect up to only four monitors. (at the recommended resolution.)
-- When this function is used, your monitor may not work properly depending on the video card. Reboot
the PC after setting the function to Off for stable screen output when not in use.
-- In case of using DVI/HDMI Input to DP Daisy Chain, please set 'Multi Display mode function' to off.
60
TROUBLESHOOTING
ENGLISH
ENG
TROUBLESHOOTING
No image is displayed.
Problem
Is the product power cord
connected?
Power is on, but the screen
appears extremely dark.
Does the 'Invalid Format'
message appear?
oes the 'No signal' message
D
appear?
Resolution
yy See if the power cord is properly connected to the outlet.
yy Adjust brightness and contrast again.
yy Backlight may need repair.
yy The signal from the PC (video card) is out of the vertical or horizontal
frequency range of the product. Adjust the frequency range by
referring to the Specifications in this manual.
yy The signal cable between PC and product is not connected. Check
the signal cable.
yy Access the input menu to check the input signal.
'Unknown Product' message appears when the product is connected.
Problem
Did you install the driver?
Resolution
yy See if the plug&play function is supported by referring to the video
card user manual.
The screen image looks abnormal.
Problem
Is the screen position wrong?
Resolution
yy D-Sub analog signal - Press the "AUTO" button in the remote control
to automatically select the optimal screen status that fits into the
current mode. If adjustment is not satisfactory, select [PICTURE] [Screen] - [Position] in OSD menu.
yy See if the video card resolution and frequency are supported by the
product. If the frequency is out of range, set to the recommended
resolution in the Control Panel "Display" Setting menu.
Do thin lines appear on the
yy D-Sub analog signal - Press the "AUTO" button in the remote control
background screen?
to automatically select an optimal screen status that fits into the
current mode. If adjustment is not satisfactory, select [PICTURE] [Screen] - [Size] in OSD menu.
Horizontal noise appears or the yy D-Sub analog signal - Press the "AUTO" button in the remote control
characters look blurred.
to automatically select an optimal screen status that fits into the
current mode. If adjustment is not satisfactory, select [PICTURE] [Screen] - [Phase] in OSD menu.
The screen is displayed
yy The proper input signal is not connected to the signal port. Connect
abnormally.
the signal cable that matches with the source input signal.
TROUBLESHOOTING
61
After-image appears on the product.
Resolution
yy If you use a fixed image for a long time, the pixels may be damaged
quickly. Use the screen-saver function.
The audio function does not work.
Problem
No sound?
Resolution
yy See if the audio cable is connected properly.
Screen color is abnormal.
Problem
Resolution
Screen has poor color resolution yy Set the number of colors to more than 24 bits (true color) Select
(16 colors).
Control Panel - Display - Settings - Color Table menu in Windows.
Screen color is unstable or
yy Check the connection status of the signal cable. Or, re-insert the PC
mono-colored.
video card.
Do black spots appear on the
yy Several pixels (red, green, white, or black color) may appear on the
screen?
screen, which can be attributable to the unique characteristics of the
LCD panel. It is not a malfunction of the LCD.
The operation does not work normally.
Problem
The power suddenly turned off.
Resolution
yy Is the sleep timer set?
yy Check the power control settings. Power interrupted.
NOTE
The software version can be updated for improvement in performance. Customer needs to ensure
yy
the compatibility of customer’s equipment with LGE software. If needed, please consult with LGE and
upload revised software version to the product according to the guidance provided by LGE.
ENG
ENGLISH
Problem
After-image appears when the
product is turned off.
62
SPECIFICATIONS
ENGLISH
ENG
SPECIFICATIONS
LCD Panel
Video Signal
Input Connector
139 cm Wide TFT (Thin Film Transistor)
LCD (Liquid Crystal Display) Panel.
Visible diagonal size : 139 cm
Pixel Pitch
0.630 mm (H) x 0.630 mm (V)
Max. Resolution
1920 x 1080 @ 60 Hz
- It may not be supported depending on the OS or video
card type.
Recommended Resolution 1920 x 1080 @ 60 Hz
- It may not be supported depending on the OS or video
card type.
Horizontal Frequency
RGB : 30 kHz to 83 kHz
HDMI/DVI/DP : 30 kHz to 83 kHz
Vertical Frequency
RGB : 50 Hz to 75 Hz
HDMI/DVI/DP : 56 Hz to 60 Hz
Synchronization Type
Separate Sync, Digital
15pin D-Sub(RGB/Component), DVI/HDMI/DP(Digital),
AV(CVBS), IR, USB, RS-232C, LAN
- You can use the Component output if you connect a 15pin D-Sub conversion cable to the RGB connector.
Screen Type
Embedded battery
Power
Power rating
55LV75A
55LV77A
Power Consumption
55LV75A
Applied
AC 100-240 V~, 50 / 60 Hz 2.1 A
AC 100-240 V~, 50 / 60 Hz 3.1 A
On Mode : 160 W Typ. 200 W Max
Smart Energy Saving Mode : 90 W Typ.
Off Mode : ≤ 0.5 W
Sleep Mode : ≤ 0.7 W
On Mode : 230 W Typ. 290 W Max
Smart Energy Saving Mode : 130 W Typ.
Off Mode : ≤ 0.5 W
Sleep Mode : ≤ 0.7 W
55LV77A
Dimensions
(Width x Height x
Depth) / Weight
W
Environmental
conditions
* Wall Bracket available VESA
600 x 400
H
D
1213.4 mm x 684.2 mm x 88.5 mm / 23 kg
Operating Temperature
0 °C to 40 °C
Operating Humidity
10 % to 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
5 % to 85 %
Product specifications shown above may be changed without prior notice due to upgrade of product
functions.
" " refers to alternating current (AC), and " " refers to direct current (DC).
SPECIFICATIONS
63
Dimensions
(Unit : mm)
684.2
1213.4
88.5
Product specifications shown above may be changed without prior notice due to upgrade of product
functions.
ENG
ENGLISH
The illustrations in this manual may differ from the actual product and accessories.
Please see the Mounting on a Wall section for sizes of screws. ( See p.9 )
64
SPECIFICATIONS
HDMI/Display Port(DTV) supported mode
RGB (PC) supported mode
ENGLISH
ENG
Resolution
Horizontal
Vertical
Frequency(kHz) Frequency(Hz)
Resolution
Horizontal
Vertical
Frequency(kHz) Frequency(Hz)
640 x 480
31.469
59.94
480 / 60p
31.5
60
31.25
50
640 x 480
37.5
75
576 / 50p
720 x 400
31.468
70.8
720 / 50p
37.5
50
800 x 600
37.879
60.317
720 / 60p
45
60
800 x 600
46.875
75
1080 / 50i
28.1
50
832 x 624
49.725
74.55
1080 / 50p
56.25
50
1024 x 768
48.363
60
1080 / 60i
33.75
60
1024 x 768
60.123
75.029
1080 / 60p
67.5
60
1280 x 720
44.772
59.855
1366 x 768
47.7
60
1280 x 1024
63.981
60.02
1280 x 1024
79.98
75.02
1680 x 1050
65.290
59.954
1920 x 1080
67.5
60
HDMI/DVI/Display Port(PC) supported mode
Component supported mode
Resolution
Horizontal
Vertical
Frequency(kHz) Frequency(Hz)
720 x 480
15.63
59.94
720 x 483
31.47
59.94
720 x 576
15.625
50.00
720 x 576
31.25
50.00
1280 x 720
45.00
60.00
1280 x 720
37.5
50
Resolution
Horizontal
Vertical
Frequency(kHz) Frequency(Hz)
640 x 480
31.469
59.94
1280 x 720
44.96
59.94
800 x 600
37.879
60.317
1920 x 1080
31.25
50.00
56.25
50
1024 x 768
48.363
60
1920 x 1080
1280 x 720
44.772
59.855
1920 x 1080
33.75
60.00
1366 x 768
47.7
60
1920 x 1080
33.72
59.94
1920 x 1080
67.5
60
1280 x 1024
63.981
60.02
1680 x 1050
65.290
59.954
1920 x 1080
67.5
60
SPECIFICATIONS
65
NOTE
NOTE
Vertical frequency: To enable the user to
yy
watch the product display, screen image
should be changed tens of times every
second like a fluorescent lamp. The vertical
frequency or refresh rate is the times of
image display per second. The unit is Hz.
Horizontal frequency: The horizontal interval
yy
is the time to display one vertical line. When
1 is divided by the horizontal interval, the
number of horizontal lines displayed every
second can be tabulated as the horizontal
frequency. The unit is kHz.
ENG
ENGLISH
When the cable is connected to the DVI,
yy
HDMI or the Display Port, you can select the
PC/DTV mode optionally. It is recommended
you to set to the PC mode when connecting
to PC; the DTV mode when connecting to
DTV.
66
IR CODES
IR CODES
ENGLISH
ENG
All models do not support the HDMI/USB function.
yy
Some key codes are not supported depending on the model.
yy
Code (Hexa)
08
Function
Note
R/C BUTTON
(POWER)
0B
INPUT
R/C BUTTON
C4
MONITOR ON
R/C BUTTON
C5
MONITOR OFF
R/C BUTTON
95
ENERGY SAVING
R/C BUTTON
DC
3D
R/C BUTTON
10 to 19
Number Key 0 to 9
R/C BUTTON
32
1/a/A
R/C BUTTON
2F
CLEAR
R/C BUTTON
02
Volume
R/C BUTTON
03
Volume
R/C BUTTON
79
ARC
R/C BUTTON
99
AUTO
R/C BUTTON
09
MUTE
R/C BUTTON
E0
BRIGHTNESS
(Page UP)
R/C BUTTON
E1
BRIGHTNESS
(Page Down)
R/C BUTTON
4D
PSM
R/C BUTTON
AA
INFO
R/C BUTTON
5F
W.BAL
R/C BUTTON
43
MENU / SETTINGS(MENU)
R/C BUTTON
40
Up ▲
R/C BUTTON
41
Down ▼
R/C BUTTON
07
Left ◄
R/C BUTTON
06
Right ►
R/C BUTTON
3F
S.MENU
R/C BUTTON
44
OK
R/C BUTTON
28
BACK
R/C BUTTON
5B
EXIT
R/C BUTTON
7E
7B
R/C BUTTON
TILE (Tile Mode)
R/C BUTTON
B1
R/C BUTTON
B0
R/C BUTTON
BA
R/C BUTTON
8F
R/C BUTTON
8E
R/C BUTTON
72
Red Key (PICTURE ID ON)
71
Green Key (PICTURE ID OFF) R/C BUTTON
R/C BUTTON
63
Yellow Key
R/C BUTTON
61
Blue Key
R/C BUTTON
CONTROLLING THE MULTIPLE PRODUCT
67
Use this method to connect several products to a single PC. You can control several products at one
yy
time by connecting them to a single PC.
In the Option menu, Set ID must be between 1 and 255 (1 - 1,000 in certain models) without being
yy
duplicated.
Connecting the cable
Connect the RS-232C cable as shown in the picture.
The RS-232C protocol is used for communication between the PC and product. You can turn the
yy
product on/off, select an input source or adjust the OSD menu from your PC.
Monitor 1
Monitor 2
Monitor 3
Monitor 4
RS-232C Cable
RS-232C Configurations
8-Wire Configurations (Cross-over RS-232C cable)
PC
DCD
RXD
TXD
GND
DTR
DSR
RTS
CTS
1
2
3
5
4
6
7
8
D-Sub 9
(Female)
Set
1
3
2
5
6
4
8
7
DCD
TXD
RXD
GND
DSR
DTR
CTS
RTS
D-Sub 9
(Female)
Communication Parameter
Baud Rate : 9600 BPS
yy
Data Length : 8 bit
yy
Parity Bit : None
yy
Stop Bit : 1 bit
yy
Flow Control : None
yy
Communication Code : ASCII code
yy
Use a crossed (reverse) cable
yy
NOTE
When using 3-wire connections (nonyy
standard), an IR daisy chain cannot be used.
ENG
ENGLISH
CONTROLLING THE MULTIPLE PRODUCT
68
CONTROLLING THE MULTIPLE PRODUCT
Command Reference List
ENGLISH
ENG
COMMAND
DATA
(Hexadecimal)
1
2
01. Power
k
a
00 to 01
02. Input Select
x
b
Refer to ‘Input Select'.
03. Aspect Ratio
k
c
Refer to ‘Aspect Ratio'.
04. Energy Saving
j
q
Refer to ‘Energy Saving'.
05. Picture mode
d
x
Refer to ‘Picture mode'.
06. Contrast
k
g
00 to 64
07. Brightness
k
h
00 to 64
08. Sharpness
k
k
00 to 64
09. Color
k
i
00 to 64
10. Tint
k
j
00 to 64
11. Color Temperature
x
u
00 to 64
12. H Position
f
q
00 to 64
13. V Position
f
r
00 to 64
14. H Size
f
s
00 to 64
15. Auto configuration
j
u
01
16. Balance
k
t
00 to 64
17. Sound mode
d
y
Refer to ‘Sound mode'.
18. Treble
k
r
00 to 64
19. Bass
k
s
00 to 64
20. Speaker
d
v
00 to 01
21. Volume Mute
k
e
00 to 01
22. Volume Control
k
f
00 to 64
23. Time 1(Years/ Months/ Days)
f
a
Refer to ‘Time 1'.
24. Time 2(Hours/ Minutes/Seconds)
f
x
Refer to ‘Time 2'.
25. Off Timer(Repeat mode/ Time)
f
e
Refer to ‘Off Timer'.
26. On Timer(Repeat Mode/ Time)
f
d
Refer to ‘On Timer'.
27. On Timer Input
f
u
Refer to ‘On Timer Input'.
28. Sleep Time
f
f
00 to 08
29. Power On Delay
f
h
00 to 64 (00 - FA in certain models)
30. Automatic Standby
m
n
00 to 01
31. Auto Off
f
g
00 to 01
32. Language
f
i
Refer to ‘Language'.
33. Power Indicator(Standby Light)
f
o
00 to 01
34. Power Indicator(Power Light)
f
p
00 to 01
35. ISM mode
j
p
Refer to ‘ISM Method'.
36. Fail Over Select
m
i
00 to 02
37. Fail Over Input Select
m
j
Refer to ‘Fail Over Input Select.'
38. Reset
f
K
00 to 02
CONTROLLING THE MULTIPLE PRODUCT
COMMAND
2
39. Tile Mode
d
d
00 to 01
40. Tile Mode Check
d
z
FF
41. Tile ID
d
i
Refer to ‘Tile ID'.
42. Tile H Position
d
e
00 to 32
43. Tile V Position
d
f
00 to 32
44. Tile H Size
d
g
00 to 32
45. Tile V Size
d
h
00 to 32
46. Natural Mode (In Tile mode)
d
j
00 to 01
47. DPM Select
f
j
00 to 01
48. FAN Control
d
o
00 to 03
49. FAN Fault Check
d
w
FF
50. Temperature Value
d
n
FF
51. Remote Lock/ key Lock
k
m
00 to 01
52. Key
m
c
Refer to ‘Key'.
53. OSD Select
k
l
00 to 01
54. Elapsed time return
d
l
FF
55. Serial No. Check
f
y
FF
56. S/W Version
f
z
FF
57. White Balance Red Gain
j
m
00 to FE
58. White Balance Green Gain
j
n
00 to FE
59. White Balance Blue Gain
j
o
00 to FE
60. Backlight
m
g
00 to 64
61. PC Power Control
d
t
00 to 01
62. PC Power
d
s
00 to 01
63. Easy Brightness Control Mode
s
s
m
s
m
k
s
m
s
u
v
t
d
d
00 to 01
64. Easy Brightness Control Schedule
65. Reading luminance values
66. Status check
67. BLU Maintenance
68. Screen mute
69. Daylight Saving
Refer to ‘Easy Brightness Control Schedule'.
Refer to ‘Reading luminance values’.
Refer to ‘Status check.’
00 to 01
00 to 01
Refer to ‘Daylight Saving.’
Note : During USB operations such as Dvix or EMF, all commands except Power (k a) and Key (m c)
yy
are not executed and treated as NG.
Some commands are not supported depending on the model.
yy
The ‘f f’ command which shows the status of a certain command does not display the OSD as the
yy
result in order to be compatible with SuperSign program.
ENG
ENGLISH
DATA
(Hexadecimal)
1
69
70
CONTROLLING THE MULTIPLE PRODUCT
Transmission / Receiving Protocol
ENGLISH
ENG
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
* [Command1]
* [Command2]
* [Set ID]
* [Data]
* [Cr]
*[]
Identifies the factory setting and the user setting modes.
Controls monitors.
Used for selecting a set you want to control. A Set ID can be assigned to each set from
1 to 255 (from 01H to FFH), or from 1 to 1,000 (from 001H to 3e8H) in certain models
under OPTION in the OSD menu. Selecting '00H' or '000H' for set ID allows the simultaneous control of all connected monitors. (Depending on the model, this feature may not
be supported.)
Transmits command data.
Data count may increase depending on the command.
Carriage Return. Corresponds to '0x0D' in ASCII code.
White Space. Corresponds to '0x20' in ASCII code.
Acknowledgement
[Command2][ ][Set ID][ ][OK/NG][Data][x]
*The Product transmits an ACK (acknowledgement) based on this format when receiving normal data. At
this time, if the data is FF, it indicates the present status data. If the data is in data write mode, it returns
the data of the PC computer.
*If a command is sent with Set ID ‘00’ (=0x00) or ‘000’(=0x000), the data is reflected to all monitors and
they do not send an acknowledgement (ACK).
*If the data value 'FF' is sent in control mode via RS-232C, the current setting value of a function can be
checked (only for some functions).
*Some commands may not be supported on some models.
CONTROLLING THE MULTIPLE PRODUCT
01. Power (Command: k a)
To control the Power On/Off the display.
Data 00 : Off
01 : On
Acknowledgement
[a][ ][Set ID][ ][OK/NG][Data][x]
* Only when the monitor set is fully powered on, the
Acknowledgement signal is returned properly.
* There may be a certain time of delay between the
Transmission and Acknowledgement signals.
04. Energy Saving (Command: j q)
To set the Energy Saving function.
Transmission
[j][q][ ][Set ID][ ][Data][Cr]
Data
00: Off
01: Minimum
02: Medium
03. Maximum
04: Auto
05. Screen Off
Acknowledgement
[q][ ][Set ID][ ][OK/NG][Data][x]
** It may not be supported depending on the model.
02. Input Select (Command: x b)
To select the Input Source for display.
Transmission
[x][b][ ][Set ID][ ][Data][Cr]
Data
20: Input (AV)
40: Component
60: RGB
70: DVI-D(PC)
80: DVI-D(DTV)
90: HDMI(HDMI1)(DTV)
A0: HDMI(HDMI1)(PC)
C0: Display Port(DTV)
D0: Display Port(PC)
91: HDMI2/SDI(DTV)
A1: HDMI2/SDI(PC)
B0: SuperSign
Acknowledgement
[b][ ][Set ID][ ][OK/NG][Data][x]
05. Picture Mode (Command: d x)
To select the Picture Mode.
Transmission
[d][x][ ][Set ID][ ][Data][Cr]
Data
00: Vivid
01: Standard
02. Cinema
03. Sport
04: Game
Acknowledgement
[x][ ][Set ID][ ][OK/NG][Data][x]
* Some input signals may not be supported
depending on the model.
03. Aspect Ratio (Command: k c)
To adjust the screen format.
Transmission
[k][c][ ][Set ID][ ][Data][Cr]
Data 01: 4:3
02: 16:9
04: Zoom
(AV, Component, HDMI/ DVI-D/ Display Port DTV)
09: Just scan (720p or more)
(Component, HDMI/ DVI-D/ Display Port DTV)
* RGB, DVI-D, HDMI/Display Port PC mode (1:1)
10 to 1F: Cinema Zoom 1 to 16
(AV, Component, HDMI/ DVI-D/ Display Port DTV)
* Available data types differ depending on the input
signal. For more information, see the aspect ratio
section of the owner's manual.
* The aspect ratio may differ depending on the
model's input configuration.
Acknowledgement
[c][ ][Set ID][ ][OK/NG][Data][x]
06. Contrast (Command: k g)
To adjust the screen contrast.
Transmission
[k][g][ ][Set ID][ ][Data][Cr]
Data 00 to 64: Contrast 0 to 100
Acknowledgement
[g][ ][Set ID][ ][OK/NG][Data][x]
ENG
ENGLISH
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
71
72
CONTROLLING THE MULTIPLE PRODUCT
07. Brightness (Command: k h)
To adjust the screen brightness.
ENGLISH
ENG
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
Data 00 to 64: Brightness 0 to 100
Acknowledgement
[h][ ][Set ID][ ][OK/NG][Data][x]
08. Sharpness (Command: k k)
To adjust the screen sharpness.
* This function is available only in AV/Component
input and DTV mode.
Transmission
[k][k][ ][Set ID][ ][Data][Cr]
Data 00 to 64: Sharpness 0 to 100
Acknowledgement
[k][ ][Set ID][ ][OK/NG][Data][x]
09. Color (Command: k i)
To adjust the screen color.
* This function is available only in AV/Component
input and DTV mode.
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
Data 00 to 64: Color 0 to 100
Acknowledgement
[i][ ][Set ID][ ][OK/NG][Data][x]
10. Tint (Command: k j)
To adjust the screen tint.
* This function is available only in AV/Component
input and DTV mode.
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
Data 00 to 64: Tint R50 to G50
Acknowledgement
[j][ ][Set ID][ ][OK/NG][Data][x]
11. Color Temperature (Command: x u)
To adjust the screen Color Temperature.
Transmission
[x][u][ ][Set ID][ ][Data][Cr]
Data 00 to 64: Warm 50 to Cool 50
Acknowledgement
[u][ ][Set ID][ ][OK/NG][Data][x]
12. H Position (Command: f q)
To adjust the screen Horizontal Position.
* This function is available only when the Tile Mode is
set to Off.
* The operational range varies depending on the
RGB input resolution.
(Only available for RGB-PC input.)
Transmission
[f][q][ ][Set ID][ ][Data][Cr]
Data 00 to 64: min. -50 (Left) to max. 50 (Right)
Acknowledgement
[q][ ][Set ID][ ][OK/NG][Data][x]
CONTROLLING THE MULTIPLE PRODUCT
Transmission
[f][r][ ][Set ID][ ][Data][Cr]
16. Balance (Command: k t)
To adjust the sound balance.
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
Data 00 to 64: Left 50 to Right 50
Acknowledgement
[t][ ][Set ID][ ][OK/NG][Data][x]
** It may not be supported depending on the model.
Data 00 to 64: min. -50 (Bottom) to max. 50 (Top)
Acknowledgement
[r][ ][Set ID][ ][OK/NG][Data][x]
14. H Size (Command: f s)
To adjust the screen Horizontal Size.
* This function is available only when the Tile Mode is
set to Off.
* The operational range varies depending on the
RGB input resolution.
(Only available for RGB-PC input.)
Transmission
[f][s][ ][Set ID][ ][Data][Cr]
Data 00 - 64: Min. -50 (Reduce) - Max. 50 (Expand)
Acknowledgement
[s][ ][Set ID][ ][OK/NG][Data][x]
15. Auto Configuration (Command: j u)
To adjust the picture position and minimize image
shaking automatically.
(Only available for RGB-PC input.)
Transmission
[j][u][ ][Set ID][ ][Data][Cr]
Data 01 : Set
Acknowledgement
[u][ ][Set ID][ ][OK/NG][Data][x]
17. Sound Mode (Command: d y)
To select the Sound Mode.
Transmission
[d][y][ ][Set ID][ ][Data][Cr]
Data
01: Standard
02: Music
03: Cinema
04: Sport
05. Game
Acknowledgement
[y][ ][Set ID][ ][OK/NG][Data][x]
** It may not be supported depending on the model.
18. Treble (Command: k r)
To adjust the Treble values.
Transmission
[k][r][ ][Set ID][ ][Data][Cr]
Data 00 to 64: Treble 0 to 100
Acknowledgement
[r][ ][Set ID][ ][OK/NG][Data][x]
** It may not be supported depending on the model.
ENG
ENGLISH
13. V Position (Command: f r)
To adjust the screen Vertical Position.
* This function is available only when the Tile Mode is
set to Off.
* The operational range varies depending on the
RGB input resolution.
(Only available for RGB-PC input.)
73
74
CONTROLLING THE MULTIPLE PRODUCT
19. Bass (Command: k s)
To adjust the Bass values.
ENGLISH
ENG
Transmission
[k][s][ ][Set ID][ ][Data][Cr]
Data 00 to 64: Bass 0 to 100
Acknowledgement
[s][ ][Set ID][ ][OK/NG][Data][x]
** It may not be supported depending on the model.
20. Speaker (Command: d v)
To select the speaker on/off.
Transmission
[d][v][ ][Set ID][ ][Data][Cr]
Data00: Off
01: On
Acknowledgement
[v][ ][Set ID][ ][OK/NG][Data][x]
** It may not be supported depending on the model.
21. Volume Mute (Command: k e)
To control the Volume Mute on/off.
Transmission
[k][e][ ][Set ID][ ][Data][Cr]
Data 00 : Mute (Volume Off)
01 : Current volume (Volume On)
Acknowledgement
[e][ ][Set ID][ ][OK/NG][Data][x]
22. Volume Control (Command: k f)
To set the playback volume.
Transmission
[k][f][ ][Set ID][ ][Data][Cr]
Data 00 to 64: Volume 0 to 100
Acknowledgement
[f][ ][Set ID][ ][OK/NG][Data][x]
** It may not be supported depending on the model.
23. Time 1(Year/ Month/ Day) (Command: f a)
To set the Time 1(Year/ Month/ Day) values.
Transmission
[f][a][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr]
Data 100 to 14: 2010 to 2030
Data 201 to 0C: January to December
Data 301 to 1F: 1 to 31
* Enter “fa [Set ID] ff” for checking Time 1(Year/
Month/ Day) values.
Acknowledgement
[a][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
24. Time 2(Hour/ Minute/ Second) (Command: f x)
To set the Time 2(Hour/ Minute/ Second) values.
Transmission
[f][x][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr]
Data1 00 to 17: 00 to 23 hours
Data2 00 to 3B: 00 to 59 minutes
Data3 00 to 3B: 00 to 59 seconds
* Enter “fx [Set ID] ff” for checking Time 2(Hour/
Minute/ Second) values.
** This command won’t work if Time 1(Year/ Month/
Day) has not been set in advance.
Acknowledgement
[x][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
CONTROLLING THE MULTIPLE PRODUCT
75
26. On Timer(Repeat Mode/ Time) (Command: f d)
To set the On Timer(Repeat mode/ Time) function.
Transmission
[f][e][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr]
Transmission
[f][d][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr]
Data1
1. F1 to F7 (Read data)
F1: Read the 1st Off Time data
F2: Read the 2nd Off Time data
F3: Read the 3rd Off Time data
F4: Read the 4th Off Time data
F5: Read the 5th Off Time data
F6: Read the 6th Off Time data
F7: Read the 7th Off Time data
2. E1-E7 (Delete one index), E0 (Delete all indexes)
E0: Delete all Off Time data
E1: Delete the 1st Off Time data
E2: Delete the 2nd Off Time data
E3: Delete the 3rd Off Time data
E4: Delete the 4th Off Time data
E5: Delete the 5th Off Time data
E6: Delete the 6th Off Time data
E7: Delete the 7th Off Time data
3. 01 to 0C (Set the day of week for Off Time)
00: Off
01: Once
02. Daily
03: Monday to Friday
04: Monday to Saturday
05: Saturday to Sunday
06. Sunday
07. Monday
08. Tuesday
09. Wednesday
0A. Thursday
0B. Friday
0C. Saturday
Data2 00 to 17: 00 to 23 Hours
Data3 00 to 3B: 00 to 59 Minutes
* To read or delete the Off Time list, set FFH for
[Data2] and [Data3].
(Example 1: fe 01 f1 ff ff - Read the 1st Off Time
data.)
(Example 2: fe 01 e1 ff ff - Delete the 1st Off Time
data.)
(Example 3: fe 01 04 02 03 - Set the Off Time to
"Monday to Saturday, 02:03".)
* This function is supported only when 1 (Year/Month/
Day) and 2 (Hour/Minute/Second) are set.
Acknowledgement
[e][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
Data1
1. F1 to F7 (Read data)
F1: Read the 1st On Time data
F2: Read the 2nd On Time data
F3: Read the 3rd On Time data
F4: Read the 4th On Time data
F5: Read the 5th On Time data
F6: Read the 6th On Time data
F7: Read the 7th On Time data
2. E1-E7 (Delete one index), E0 (Delete all indexes)
E0: Delete all On Time data
E1: Delete the 1st On Time data
E2: Delete the 2nd On Time data
E3: Delete the 3rd On Time data
E4: Delete the 4th On Time data
E5: Delete the 5th On Time data
E6: Delete the 6th On Time data
E7: Delete the 7th On Time data
3. 01 to 0C (Set the day of week for On Time)
00: Off
01: Once
02. Daily
03: Monday to Friday
04: Monday to Saturday
05: Saturday to Sunday
06. Sunday
07. Monday
08. Tuesday
09. Wednesday
0A. Thursday
0B. Friday
0C. Saturday
Data2 00 to 17: 00 to 23 Hours
Data3 00 to 3B: 00 to 59 Minutes
* To read or delete the Off Time list, set FFH for
[Data2] and [Data3].
(Example 1: fd 01 f1 ff ff - Read the 1st On Time
data.)
(Example 2: fd 01 e1 ff ff - Delete the 1st On Time
data.)
(Example 3: fd 01 04 02 03 - Set the On Time to
"Monday to Saturday, 02:03".)
* This function is supported only when 1 (Year/Month/
Day) and 2 (Hour/Minute/Second) are set.
Acknowledgement
[d][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
ENG
ENGLISH
25. Off Timer(Repeat Mode/ Time) (Command: f e)
To set the Off Timer(Repeat Mode/ Time) function.
76
CONTROLLING THE MULTIPLE PRODUCT
ENGLISH
ENG
27. On Timer Input (Command: f u)
To select an external input for the current On Time
setting and add a new schedule or change the
existing schedule.
Transmission
[f][u][ ][Set ID][ ][Data1][Cr]
[f][u][ ][Set ID][ ][Data1][Data2][Cr]
Data (Add schedule)
20: Input (AV)
40: Component
60. RGB
70: DVI-D
90: HDMI (HDMI1)
C0: Display Port
91: HDMI2/SDI
B0:SuperSign
Data1 (Change schedule)
1. F1 to F7 (Read data)
F1: Select the 1st schedule input
F2: Select the 2nd schedule input
F3: Select the 3rd schedule input
F4: Select the 4th schedule input
F5: Select the 5th schedule input
F6: Select the 6th schedule input
F7: Select the 7th schedule input
Data2
20: Input (AV)
40: Component
60: RGB
70: DVI-D
90: HDMI (HDMI1)
C0: Display Port
91: HDMI2/SDI
B0:SuperSign
* To read the schedule input, enter FFH for [Data2].
If no schedule is available for [Data1] when
attempting to read or change the schedule data, the
text NG will be displayed and the operation fails.
(Example 1: fu 01 60 - Move each schedule input
down one row and save the 1st schedule input in
RGB mode.)
(Example 2: fu 01 f1 ff - Read the 1st schedule input.)
(Example 3: fu 01 f3 20 - Change the 3rd data
schedule input to the current On Time and AV input.
If there is no third schedule, the text NG will be
displayed and the operation fails.)
* This function is supported only when 1 (Year/Month/
Day), 2 (Hour/Minute/Second), On Time (Repeat
Mode/Time) are set.
** It may not be supported depending on the model.
Acknowledgement
[u][ ][Set ID][ ][OK/NG][Data][x]
[u][ ][Set ID][ ][OK/NG][Data1][Data2][x]
28. Sleep Time (Command: f f)
To set the Sleep Time.
Transmission
[f][f][ ][Set ID][ ][Data][Cr]
Data
00: Off (Sleep Timer off)
01: 10 min.
02: 20 min.
03: 30 min.
04: 60 min.
05: 90 min.
06: 120 min.
07: 180 min.
08: 240 min.
Acknowledgement
[f][ ][Set ID][ ][OK/NG][Data][x]
29. Power On Delay (Command: f h)
To set the schedule delay when the power is turned
on. (Unit: Second)
Transmission
[f][h][ ][Set ID][ ][Data][Cr]
Data 00 to 64: min. 0 to max. 100 (sec.)
(Data 00 - FA in certain models: min 0 - max 250
(sec.))
Acknowledgement
[h][ ][Set ID][ ][OK/NG][Data][x]
30. Automatic Standby (Command: m n)
To set the Automatic Standby function.
Transmission
[m][n][ ][Set ID][ ][Data][Cr]
Data 00: Off (No off after 4 hours)
01: 4 Hours (Off after 4 hours)
Acknowledgement
[n][ ][Set ID][ ][OK/NG][Data][x]
CONTROLLING THE MULTIPLE PRODUCT
31. Auto Off (Command: f g)
To set the Auto Off function.
Data 00: Off (No off after 15 minutes)
01: 15 min.(Off after 15 minutes)
Acknowledgement
[g][ ][Set ID][ ][OK/NG][Data][x]
32. Language (Command: f i)
To set the language for OSD.
Transmission
[f][i][ ][Set ID][ ][Data][Cr]
Data
00: Czech
01: Danish
02: German
03: English
04: Spanish (EU)
05: Greek
06: French
07: Italian
08: Dutch
09: Norwegian
0A: Portuguese
0B: Portuguese (BR)
0C: Russian
0D: Finnish
0E: Swedish
0F: Korean
10: Chinese (Mandarin)
11: Japanese
12: Yue Chinese (Cantonese)
34. Power Indicator (Power Light) (Command: f p)
To set the Power Indicator (Power Light) function.
Transmission
[f][p][ ][Set ID][ ][Data][Cr]
Data 00: Off
01: On
** It may not be supported depending on the model.
Acknowledgement
[p][ ][Set ID][ ][OK/NG][Data][x]
35. ISM mode (Command: j p)
To select ISM method for avoiding having a fixed
image remain on screen.
Transmission
[j][p][ ][Set ID][ ][Data][Cr]
Data
01: Inversion
02: Orbiter
04: White Wash
08. Normal
Acknowledgement
[p][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement
[i][ ][Set ID][ ][OK/NG][Data][x]
33. Power Indicator (Standby Light) (Command: f o)
To set the Power Indicator (Standby Light) function.
Transmission
[f][o][ ][Set ID][ ][Data][Cr]
Data 00: Off
01: On
** It may not be supported depending on the model.
Acknowledgement
[o][ ][Set ID][ ][OK/NG][Data][x]
36. Fail Over Select (Command: m i)
To set the Fail Over function.
Transmission
[m][i][ ][Set ID][ ][Data][Cr]
Data 00: Off
01: Auto
02: Manual
Acknowledgement
[i][ ][Set ID][ ][OK/NG][Data][x]
ENG
ENGLISH
Transmission
[f][g][ ][Set ID][ ][Data][Cr]
77
78
CONTROLLING THE MULTIPLE PRODUCT
ENGLISH
ENG
37. Fail Over Input Select (Command: m j)
To select the input source for auto switch.
* This command is only available when the fail over
(auto) mode is set to Manual.
Transmission
[m][j][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr]
[ ][Data4][ ][Data5][Cr]
Data 1 to 5 (Priority 1 to 5)
60: RGB
70: DVI-D
90: HDMI(HDMI1)
C0: Display Port
91: HDMI2/SDI
* The number of data items differs depending on the
model.
40. Tile Mode Check (Command: d z)
To check Tile Mode status.
Transmission
[d][z][ ][Set ID][ ][Data][Cr]
Data FF: Check Tile Mode status.
** It may not be supported depending on the model.
Acknowledgement
[z][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
Data1
Data2
Data3
00: Tile Mode Off
01: Tile Mode On
00 to 0F: Tile Row
00 to 0F: Tile Column
Acknowledgement
[j][ ][SetID][ ][OK/NG][Data1][Data2][Data3][Data4]
[ ][Data5][x]
41. Tile ID (Command: d i)
To set Tile ID.
Transmission
[d][i][ ][Set ID][ ][Data][Cr]
38. Reset (Command: f k)
To execute the Picture, Screen, Audio and Factory
reset function.
(Screen Reset can only be performed in RGB input
mode.)
Transmission
[f][k][ ][Set ID][ ][Data][Cr]
Data
Data 01 to E1: Tile ID 01 to 225**
FF: Check Tile ID
** Data could not be set over (Tile Column) x (Tile
Row).
** It may not be supported depending on the model.
Acknowledgement
[i][ ][Set ID][ ][OK/NG][Data][x]
*NG will be return if data is over (Tile Column) x (Tile
Row), except 0xFF.
00: Picture Reset
01: Screen Reset
02: Factory Reset
03: Audio Reset
Acknowledgement
[k][ ][Set ID][ ][OK/NG][Data][x]
42. Tile H Position (Command: d e)
To adjust the Tile Horizontal position.
* This function is available only when the Natural
option of the Tile Mode is set to Off while the Tile
Mode set to On.
39. Tile Mode (Command: d d)
To set a Tile Mode and Tile Column/ Row values.
Transmission
[d][d][ ][Set ID][ ][Data][Cr]
Data 00 to FF: 1st byte - Tile Row
2nd byte - Tile Column
*00, 01, 10, 11 means Tile Mode Off
** It may not be supported depending on the model.
Acknowledgement
[d][ ][Set ID][ ][OK/NG][Data][x]
Transmission
[d][e][ ][Set ID][ ][Data][Cr]
Data 00 to 32: -50 (Left) to 0 (Right)
*Left/Right values depend on Tile H size.
** It may not be supported depending on the model.
Acknowledgement
[e][ ][Set ID][ ][OK/NG][Data][x]
CONTROLLING THE MULTIPLE PRODUCT
Transmission
[d][f][ ][Set ID][ ][Data][Cr]
Data 0 to 32: 0 (Bottom) to 50 (Top)
* Bottom/Top values depend on Tile Vertical size.
** It may not be supported depending on the model.
Acknowledgement
[f][ ][Set ID][ ][OK/NG][Data][x]
44. Tile H Size (Command: d g)
To adjust the Tile Horizontal Size.
*Set Tile H Position to 0x32 before setting Tile H
Size.
* This function is available only when the Natural
option of the Tile Mode is set to Off while the Tile
Mode set to On.
Transmission
[d][g][ ][Set ID][ ][Data][Cr]
Data 00 to 32: 0 to 50
** It may not be supported depending on the model.
Acknowledgement
[g][ ][Set ID][ ][OK/NG][Data][x]
46. Natural Mode (In Tile Mode) (Command : d j)
To display the image naturally, the part of the image
that would normally be displayed in the gap between
the monitors is omitted.
Transmission
[d][j][ ][Set ID][ ][Data][Cr]
Data 00: Off
01: On
Acknowledgement
[j][ ][Set ID][ ][OK/NG][Data][x]
47. DPM Select (Command: f j)
To set the DPM (Display Power Management)
function.
Transmission
[f][j][ ][Set ID][ ][Data][Cr]
Data 00: Off
01: On
* Data settings may vary depending on your model
as below.
Data 00: Off
01: 5 sec.
02: 10 sec.
03: 15 sec.
04: 1 min.
05: 3 min.
06: 5 min.
07: 10 min.
Acknowledgement
[j][ ][Set ID][ ][OK/NG][Data][x]
45. Tile V Size (Command: d h)
To adjust the Tile Vertical size.
*Set Tile V Position to 0x00 before setting Tile V
Size.
* This function is available only when the Natural
option of the Tile Mode is set to Off while the Tile
Mode set to On.
Transmission
[d][h][ ][Set ID][ ][Data][Cr]
Data 00 to 32: 0 to 50
** It may not be supported depending on the model.
Acknowledgement
[h][ ][Set ID][ ][OK/NG][Data][x]
48. FAN Control (Command : d o)
To set the Fan mode.
Transmission
[d][o][ ][Set ID][ ][Data][Cr]
Data 00: Auto
01: On
02: Manual
03: Off
** It may not be supported depending on the model.
Acknowledgement
[o][ ][Set ID][ ][OK/NG][Data][x]
ENG
ENGLISH
43. Tile V Position (Command: d f)
To adjust the Tile Vertical position.
* This function is available only when the Natural
option of the Tile Mode is set to Off while the Tile
Mode set to On.
79
80
CONTROLLING THE MULTIPLE PRODUCT
49. FAN Fault Check (Command: d w)
To check the fan errors.
ENGLISH
ENG
Transmission
[d][w][ ][Set ID][ ][Data][Cr]
Data FF: Read the status
Acknowledgement
[w][ ][Set ID][ ][OK/NG][Data][x]
Data 00: Fan fault
01: Fan OK
02: Model without a Fan
50. Temperature Value (Command: d n)
To check the inside temperature value.
Transmission
[d][n][ ][Set ID][ ][Data][Cr]
Data FF: Check the status
Acknowledgement
[n][ ][Set ID][ ][OK/NG][Data][x]
[n][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
52. Key (Command: m c)
To send a key code of the IR remote control.
Transmission
[m][c][ ][Set ID][ ][Data][Cr]
DataIR_KEY_CODE
Acknowledgement
[c][ ][Set ID][ ][OK/NG][Data][x]
For a key code, see the IR Code.
* Some key codes are not supported depending on
the model.
53. OSD Select (Command: k l)
To select OSD(On Screen Display) on/off.
Transmission
[k][l][ ][Set ID][ ][Data][Cr]
Data 00: Off
01: On
Acknowledgement
[l][ ][Set ID][ ][OK/NG][Data][x]
* Temperature is displayed in hexadecimal.
51. Remote Controller Lock/ Key Lock
(Command: k m)
When the remote control and front keys are locked in
standby mode, the power cannot be turned on using
the remote control or front power button.
Transmission
[k][m][ ][Set ID][ ][Data][Cr]
Data 00: Off (Lock Off)
01: On (Lock On)
* Display will not be turned on by power on key of
remote controller and front panel control keys, if key
is locked on in standby mode.
Acknowledgement
[m][ ][Set ID][ ][OK/NG][Data][x]
** It may not be supported depending on the model.
54. Elapsed time return (Command: d l)
To check the panel used time.
Transmission
[d][l][ ][Set ID][ ][Data][Cr]
Data FF: Read the status
Acknowledgement
[l][ ][Set ID][ ][OK/NG][Data][x]
* Returned data means used hours in hexadecimal.
CONTROLLING THE MULTIPLE PRODUCT
55. Serial No.Check (Command: f y)
To check the Serial Numbers.
Data FF: Check the product Serial Number
Acknowledgement
[y][ ][Set ID][ ][OK/NG][Data][x]
* Data is ASCII code.
56. S/W Version (Command: f z)
To check the Software Version.
Transmission
[f][z][ ][Set ID][ ][Data][Cr]
Data FF: Check the Software version
Acknowledgement
[z][ ][Set ID][ ][OK/NG][Data][x]
58. White Balance Green Gain (Command: j n)
To set the White Balance Green Gain.
Transmission
[j][n][ ][Set ID][ ][Data][Cr]
Data 00 to FE: Green Gain 0 to 254
Acknowledgement
[n][ ][Set ID][ ][OK/NG][Data][x]
* Using the remote control, you can adjust the value
from 0 to 255. With RS-232C, you can adjust the
value from 0 to 254.
59. White Balance Blue Gain (Command: j o)
To set the White Balance Blue Gain.
Transmission
[j][o][ ][Set ID][ ][Data][Cr]
Data 00 to FE: Blue Gain 0 to 254
Acknowledgement
[o][ ][Set ID][ ][OK/NG][Data][x]
* Using the remote control, you can adjust the value
from 0 to 255. With RS-232C, you can adjust the
value from 0 to 254.
57. White Balance Red Gain (Command: j m)
To set the White Balance Red Gain.
Transmission
[j][m][ ][Set ID][ ][Data][Cr]
Data 00 to FE: Red Gain 0 to 254
Acknowledgement
[m][ ][Set ID][ ][OK/NG][Data][x]
* Using the remote control, you can adjust the value
from 0 to 255. With RS-232C, you can adjust the
value from 0 to 254.
60. Backlight (Command: m g)
To adjust the screen backlight.
Transmission
[m][g][ ][Set ID][ ][Data][Cr]
Data 00 to 64: Backlight 0 to 100
Acknowledgement
[g][][set ID][][OK/NG][Data][x]
** It may not be supported depending on the model.
ENG
ENGLISH
Transmission
[f][y][ ][Set ID][ ][Data][Cr]
81
82
CONTROLLING THE MULTIPLE PRODUCT
ENGLISH
ENG
61. PC Power Control (Command: d t)
To control the PC power if the PC and the monitor
are synchronized.
Transmission
[d][t][ ][Set ID][ ][Data][Cr]
Data
00: S
ynchronized (When the monitor is off, the PC is
also turned off.)
01: N
ot synchronized (The monitor is off but the PC
is on.)
02: K
eeps your PC powered on (When you turn on
the monitor while the PC is turned off, the PC is
turned on.).
** It may not be supported depending on the model.
Acknowledgement
[t][ ][Set ID][ ][OK][Data][x]
62. PC Power (Command: d s)
Control the PC power.
Transmission
[d][s][ ][Set ID][ ][Data][Cr]
Data 00: PC is turned off.
01: PC is turned on.
** It may not be supported depending on the model.
Acknowledgement
[s][ ][Set ID][ ][OK][Data][x]
64. Easy Brightness Control Schedule (Command: s
s)
Sets the Easy Brightness Control Schedule.
Transmission
[s][s][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr]
Data1
1. F1 - F6 (Data Reading Functions)
F1: Reads the data of the 1st Easy Brightness
Control
F2: Reads the data of the 2nd Easy Brightness
Control
F3: Reads the data of the 3rd Easy Brightness
Control
F4: Reads the data of the 4th Easy Brightness
Control
F5: Reads the data of the 5th Easy Brightness
Control
F6: Reads the data of the 6th Easy Brightness
Control
2. E1-E6 (Deletes One Index), E0 (Delete All
Indexes)
E0: Deletes all Easy Brightness Controls
E1: Deletes the 1st Easy Brightness Control
E2: Deletes the 2nd Easy Brightness Control
E3: Deletes the 3rd Easy Brightness Control
E4: Deletes the 4th Easy Brightness Control
E5: Deletes the 5th Easy Brightness Control
E6: Deletes the 6th Easy Brightness Control
3. 00-17: 00 - 23:00
Data2 00-3B: 00 - 59 minutes
Data3 00-64: backlight 0 - 100
* To read or delete the configured Easy Brightness
Control list, set [Data2][Data3] to FF.
(ex1: ss 01 f1 ff ff - Reads the 1st index data from the
Easy Brightness Control.
ex2: ss 01 e1 ff ff - Deletes the 1st index data from
the Easy Brightness Control.
ex3: ss 01 07 1E 46 - Adds a schedule to the
backlight 70 at 07:30.)
Acknowledgement
[s][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
** It may not be supported, depending on the model.
63. Easy Brightness Control Mode (Command: s m)
Selects ON/OFF of Easy Brightness Control Mode.
Transmission
[s][m][ ][Set ID][ ][Data][Cr]
Data 00: Easy Brightness Control OFF
01: Easy Brightness Control ON
* It does not work if the current time is not set up.
** It may not be supported, depending on the model.
Acknowledgement
[m][ ][Set ID][ ][OK/NG][Data][x]
CONTROLLING THE MULTIPLE PRODUCT
65. Reading luminance values (Command: m u)
Reads luminance values.
Acknowledgement
[u][][SetID][][OK/NG][Data1][Data2][Data3][Data4]
[Data5][Data6][Data7][x]
Data1 00-64 backlight 0-100
Data2 00-ff: Upper 2-byte of CA210 measured value
Data3 00-ff: Lower 2-byte of CA210 measured value
CA210 measured value Hex: 0000-ffff, Decimal: 0 65535
Data4 00-ff: Upper 2-byte of BLU measured value
Data5 00-ff: Lower 2-byte of BLU measured value
Data6 00-ff: Upper 2 bytes of BLU No. 2 sensor
measured value
Data7 00-ff: Lower 2 bytes of BLU No. 2 sensor
measured value
BLU measured value Hex: 0000-ffff, Decimal: 0 - 65535
* CA210 measured value is entered through the
calibration procedure during final assembly. Default
value is 0 before calibration.
** It may not be supported, depending on the model.
When the Data is 07
Data100: All temperature sensors fail
01: Top normal, Bottom fail, Main fail
02: Top fail, Bottom normal, Main fail
03: Top normal, Bottom normal, Main fail
04: Top fail, Bottom fail, Main normal
05: Top normal, Bottom fail, Main fail
06: Top fail, Bottom normal, Main fail
07: All temperature sensors normal
When the Data is 08
Acknowledgement
[v][ ][SetID][ ][OK/NG][Data][Data1][Data2][Data3][x]
Data1: Temperature of the top sensor area when the
set is powered off.
Data2: Temperature of the bottom sensor area when
the set is powered off.
Data3: Temperature of the main sensor area when
the set is powered off.
When the Data is 09
Acknowledgement
[v][ ][SetID][ ][OK/NG][Data][Data1][Data2][x]
Data1 00-ff: Upper 2-byte of Fan Speed
Data2 00-ff: Lower 2-byte of Fan Speed
Fan Speed: Hex 0-20D0, Decimal 0-8400
When the Data is 0x10
Acknowledgement
[v][ ][SetID][ ][OK][Data][Data1][x]
66. Status check (Command: s v)
Check various statuses.
Transmission
[s][v][ ][Set ID][ ][Data][ ][FF][Cr]
Data 05: Check the normal operation of No.1 and
No.2 luminance sensors.
06: luminance sensor being used:
07: Checks whether the main temperature
sensors as well as the sensors located at the
top and bottom work normally.
08: Temperature of each temperature sensor
when the set is powered off.
09: Fan Speed
0x10: RGB sensing OK/NG (Check Screen)
Acknowledgement
[v][ ][Set ID][ ][OK/NG][Data][Data1][x]
When the Data is 05
Data100: All normal
01: BLU sensor 1 normal, BLU sensor 2 fail
02: BLU sensor 1 fail, BLU sensor 2 normal
03: All fail
When the Data is 06
Data100: No.1 luminance sensor is being used
01: No.2 luminance sensor is being used
Data1 00: RGB all NG
01: B NG. G NG, R OK
02: B NG. G OK, R NG
03: B OK. G OK, R NG
04: B NG. G NG, R OK
05: B OK. G NG, R OK
06: B NG. G OK, R OK
07: RGB all OK
08: Loading
** It may not be supported, depending on the model.
ENG
ENGLISH
Transmission
[m][u][ ][Set ID][ ][FF][Cr]
83
84
CONTROLLING THE MULTIPLE PRODUCT
67. BLU Maintenance (Command: m t)
Select ON/OFF of BLU Maintenance.
ENGLISH
ENG
Transmission
[m][t][ ][Set ID][ ][Data][Cr]
Data 00: BLU Maintenance OFF
01: BLU Maintenance ON
** It may not be supported, depending on the model.
Acknowledgement
[t][ ][Set ID][ ][OK/NG][Data][x]
68. Screen mute (Command: k d)
Turns the screen on or off.
Transmission
[k][d][ ][Set ID][ ][Data][Cr]
Data 00: Turns the screen on.
01: Turns the screen off.
Acknowledgement
[d][ ][Set ID][ ][OK/NG][Data][x]
69. Daylight Saving (Command: s d)
To set the Daylight saving function.
Transmission
[s][d][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][ ][Data4]
[ ][Data5][Cr]
Data 00: Off (Data2~5: FFH)
01: Start Time
02: End Time
Data2 01~0C: January to December
Data3 01~06: 1 ~ 6th week
* The maximum number of [Data3] differs depending
on Date.
Data4 00~06 ( Sun. ~ Sat. )
Data5 00~17: 00 ~ 23 hours
* To read the Start Time/End Time, enter FFH for
[Data2]~[Data5].
(ex1: sd 01 01 ff ff ff ff - To check the Start Time
ex2: sd 01 02 ff ff ff ff - To check the End Time)
* This function is supported only when 1 (Year/Month/
Day) and 2 (Hour/Minute/Second) are set.
Acknowledgement
[d][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][Data4]
[Data5][x]
** It may not be supported depending on the model.
To obtain the source code under GPL, LGPL, MPL, and
other open source licenses, that is contained in this
product, please visit http://opensource.lge.com .
In addition to the source code, all referred license terms,
warranty disclaimers and copyright notices are available
for download.
LG Electronics will also provide open source code to you
on CD-ROM for a charge covering the cost of performing
such distribution (such as the cost of media, shipping, and
handling) upon email request to opensource@lge.com.
This offer is valid for a period of three years after our last
shipment of this product. This offer is valid to anyone in
receipt of this information.
Make sure to read the Safety Precautions before using the
product.
Keep the Owner's Manual (CD) in an accessible place for
future reference.
The model and serial number of the SET is located on the
back and one side of the SET. Record it below should you
ever need service.
MODEL
SERIAL
NOTE
55LV77A is not certified with EPA’s ENERGYSTAR.
yy
ENERGY STAR® is a set of power-saving
guidelines issued by the U.S.Environmental
Protection Agency (EPA).
As an ENERGY STAR® Partner LGE U. S. A.,
Inc. has determined that this product
meets the ENERGY STAR® guidelines for
energy efficiency.
Refer to ENERGYSTAR.gov for more information on the
ENERGY STAR® program.
Temporary noise is normal when powering ON or OFF
this device.
Download PDF