LG | D2342P | LG D2342P-PN Owner’s Manual

ENGLISH
OWNER’S MANUAL
CINEMA 3D MONITOR
Please read this manual carefully before operating
your set and retain it for future reference.
CINEMA 3D MONITOR MODEL
D2342P
www.lg.com
ENG.indd 1
2011-04-05 �� 1:20:32
2
TABLE OF CONTENTS
CONTENTS
ENGLISH
ENG
3
ASSEMBLING AND PREPARING
22 PROPER POSTURE
3
Unpacking
22
Proper posture for using the Monitor set.
4
Parts and buttons
22
Precautions to take when viewing 3D im-
6
Setting up the Monitor set
6
- Attaching the Stand Base
6
- Detaching the Stand Base and Body
7
- Mounting on a table
8
- Mounting on a wall
ages
10 USING THE MONITOR SET
10
Connecting to a PC
10
- D-SUB connection
10
- DVI-D connection
10
- HDMI connection
12 CUSTOMIZING SETTINGS
12
Accessing The Main Menus
13
Customizing Settings
13
- Menu Settings
14
- 3D Settings(Only 3D mode)
14
- Volume Settings (Only supported in
HDMI)
15
- SUPER ENERGY SAVING Settings
16 TROUBLESHOOTING
18 TROUBLESHOOTING WHEN
USING 3D MODE
19 SPECIFICATIONS
20
Preset Modes (Resolution)
20
HDMI 3D TIMING
20
Indicator
21 PRECAUTIONS TO TAKE
WHEN VIEWING 3D IMAGES
ENG.indd 2
2011-04-05 �� 1:20:32
3
ASSEMBLING AND PREPARING
ASSEMBLING AND PREPARING
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual product
and accessories.
CD(Owner's Manual) /
Card
TriDef 3D software Program CD /
Quick Installation Guide
Power Cord
Stand Body
D-SUB Cable
(This signal cable may be attached
to this product before shipping out.)
DVI-D Cable
(This cable is not included in all
countries.)
Stand Base
3D Glasses
(Normal type)
3D Glasses
(Clip-on type)
ENG
ENGLISH
Unpacking
CAUTION
Do not use any unapproved accessories to ensure the safety and product life span.
yy
Any damages or injuries by using unapproved accessories are not covered by the warranty.
yy
NOTE
The accessories supplied with your product may vary depending on the model.
yy
Product specifications or contents in this manual may be changed without prior notice due to upgrade
yy
of product functions.
User should use shielded signal interface cables (RGB cable / DVI-D cable) with ferrite cores to
yy
maintain standard compliance for the product.
ENG.indd 3
2011-04-05 �� 1:20:34
4
ASSEMBLING AND PREPARING
Parts and buttons
ENGLISH
ENG
Power Indicator
yyLighting On: Turned on
yyLighting Off: Turned off
(Power Button)
Button (See p.12)
AC-IN/
䔜㹷彺⅌
D-SUB
DVI-D
HDMI
Connection panel (See p.10)
ENG.indd 4
2011-04-05 �� 1:20:34
5
ASSEMBLING AND PREPARING
Button
Description
Accesses the main menus.(See p.13)
OSD LOCKED/
UNLOCKED
This function allows you to lock the current control settings, so
that they cannot be inadvertently changed.
Press and hold the MENU button for several seconds.
The message "OSD LOCKED" should appear.
You can unlock the OSD controls at any time by pushing
the MENU button for several seconds. The message "OSD
UNLOCKED" should appear.
SUPER ENERGY
SAVING Button
Use this button to enter SUPER ENERGY SAVING menu.For
more information.(See p.15)
3D
3D display settings.(See p.14)
AUTO
When adjusting your display settings, always press the AUTO button on the MONITOR
SETUP OSD. (Only supported in Analog Mode)
ENG
ENGLISH
MENU
The best display mode 1920 x 1080
VOLUME (Only HDMI mode) Adjust the volume of the Monitor set.(See p.14)
INPUT
You can choose the input signal.
yy When two input signals are at least are connected, you can select the input signal
(D-SUB/DVI/HDMI) you want.
yy When only one signal is connected, it is automatically detected. The default setting is
D-SUB.
EXIT
Exit the OSD(On Screen Display).
(Power Button)
Turns the power on or off.
Power Indicator
ENG.indd 5
The power indicator stays blue if the display is running
properly (On Mode). If the display is in Sleep Mode, the power
indicator blinks blue.
2011-04-05 �� 1:20:34
6
ASSEMBLING AND PREPARING
ENGLISH
ENG
Setting up the Monitor set
Detaching the Stand Base and Body
Attaching the Stand Base
1 Place the Monitor set with the screen side
1 Place the Monitor set with the screen side
down on a flat and cushioned surface.
2 Pull out the Stand Base and Stand Body from
down on a flat and cushioned surface.
the Monitor set.
CAUTION
Lay a foam mat or soft protective cloth
on the surface to protect the screen from
damage.
2 Assemble the Stand Body into the product in
the correct direction as shown in the picture.
Make sure you push it until you hear it “click”.
Hinge Body
3 Turn the screw to the left with a Coin, and then
pull out the Stand Base from the Stand Body.
Stand Body
3 Attach the Stand Base and then tighten the
screw to the right with a Coin.
CAUTION
Stand Base
ENG.indd 6
This illustration depicts the general model of
yy
connection. Your monitor may differ from the
items shown in the picture.
Do not carry the product upside down holding
yy
only the stand base. The product may fall
and get damaged or injure your foot.
2011-04-05 �� 1:20:35
7
ASSEMBLING AND PREPARING
Mounting on a table
WARNING
position on a table.
Leave a 10 cm (minimum) space from the wall
for proper ventilation.
ENG
ENGLISH
1 Lift and tilt the Monitor set into its upright
When you adjust the angle, do not hold the
bottom of the Monitor set frame as shown on
the following illustration, as may injure your
fingers.
10 cm
10 cm
10 cm
10 cm
Do not touch or press the screen when
adjusting the angle of the monitor.
2 Connect the Power Cord to a wall outlet.
NOTE
Tilt from +15 to -5 degrees up or down to adjust
the angle of the Monitor set to suit your view.
-5
15
3 Press (Power) button on the front switch
panel to turn the power on.
Front
Rear
CAUTION
Unplug the power cord before moving the
Monitor to another location. Otherwise electric
shock may occur.
ENG.indd 7
2011-04-05 �� 1:20:36
8
ASSEMBLING AND PREPARING
Using the Kensington security system
ENGLISH
ENG
The Kensington security system connector is
located at the back of the Monitor set. For more
information of installation and using, refer to the
manual supplied with the Kensington security
system or visit http://www.kensington.com .
Mounting on a wall
For proper ventilation, allow a clearance of 10 cm
on each side and from the wall. Detailed
instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and
Setup Guide.
Connect the Kensington security system cable
between the Monitor set and a table.
10 cm
10 cm
10 cm
10 cm
NOTE
The Kensington security system is optional.
You can obtain it from most electronics stores.
ENG.indd 8
When you install the Monitor set using a wall
mounting interface (optional parts), attach it
carefully so it will not drop.
Please use VESA standard as below.
784.8 mm (30.9 inch) and under
yy
* Wall Mount Pad Thickness : 2.6 mm
* Screw : Φ 4.0 mm x Pitch 0.7 mm x
Length 10 mm
787.4 mm (31.0 inch) and above
yy
* Please use VESA standard wall mount pad
and screws.
2011-04-05 �� 1:20:37
ASSEMBLING AND PREPARING
D2342P
VESA (A x B)
Standard screw
Number of screws
Wall mount bracket
(optional)
75 x 75
M4
4
RW120
ENG
ENGLISH
Model
9
CAUTION
Disconnect the power cord first, and then
yy
move or install the Monitor set. Otherwise
electric shock may occur.
If you install the Monitor set on a ceiling or
yy
slanted wall, it may fall and result in severe
injury.
Use only an authorized LG wall mount
yy
and contact the local dealer or qualified
personnel.
Do not over tighten the screws as this may
yy
cause damage to the Monitor set and void
your warranty.
Use only screws and wall mounts that
yy
meet the VESA standard. Any damages
or injuries by misuse or using an improper
accessory are not covered by the warranty.
NOTE
Use the screws that are listed on the VESA
yy
standard screw specifications.
The wall mount kit will include an installation
yy
manual and necessary parts.
The wall mount bracket is optional. You can
yy
obtain additional accessories from your local
dealer.
The length of screws may differ depending
yy
on the wall mount. Be sure to use the proper
length.
For more information, refer to the
yy
instructions supplied with the wall mount.
ENG.indd 9
2011-04-05 �� 1:20:37
10
USING THE MONITOR SET
USING THE MONITOR SET
ENGLISH
ENG
Connecting to a PC
DVI-D connection
Your Monitor set supports Plug & Play*.
yy
*Plug & Play: A PC recognizes a connected
device that users connect to a PC and turn
on, without device configuration or user
intervention.
Transmits a digital video signal from your PC to
the Monitor set. Connect the PC and the Monitor
set with a DVI cable as shown in the following
illustrations.
D-SUB
D-SUB connection
DVI-D
HDMI
Transmits analog video from your PC to the
Monitor set. Connect the PC and the Monitor set
with the supplied D-sub 15 pin signal cable as
shown in the following illustrations.
D-SUB
DVI-D
HDMI
DVI OUT
HDMI connection
Transmits the digital video and audio signals from
your PC or A/V to the Monitor set. Connect the PC
or A/V and the Monitor set with the HDMI cable as
shown in the following illustrations.
RGB OUT
D-SUB
DVI-D
HDMI
NOTE
When using a D-Sub signal input cable
yy
connector for Macintosh
HDMI OUT
Mac adapter
yy
For Apple Macintosh use, a separate plug
adapter is needed to change the 15 pin
high density (3 row) D-SUB VGA connector
on the supplied cable to a 15 pin 2 row
connector.
ENG.indd 10
HDMI OUT
NOTE
If you use HDMI PC, it can cause compatibility
yy
problem.
2011-04-05 �� 1:20:38
11
USING THE MONITOR SET
CAUTION
NOTE
When you want to use two PC in our Monitor,
yy
please connect the signal cable(D-SUB/
DVI-D/HDMI) respectively in Monitor set.
If you turn the Monitor set on while it is cold,
yy
the screen may flicker. This is normal.
Some red, green, or blue spots may appear
yy
on the screen. This is normal.
ENG.indd 11
Press the power button on the front panel to turn
the power on. When monitor power is turned on,
the "Self Image Setting" Function is executed
automatically. (Only supported in Analog Mode)
ENG
ENGLISH
Connect the signal
yy
input cable and tighten
it by turning the screws
clockwise.
Do not press the screen with your finger for yy
a long time as this may result in temporary
distortion on the screen.
Avoid displaying a fixed image on the
yy
screen for a long period of time to prevent
image burn. Use a screensaver if possible.
Self Image Setting Function
NOTE
"Self Image Setting" Function.
yy
This function provides the user with optimal
display settings.When the user connects
the monitor for the first time, this function
automatically adjusts the display to optimal
settings for individual input signals.(Only
supported in Analog Mode)
‘AUTO’ Function.
yy
When you encounter problems such as
blurry screen, blurred letters, screen flicker
or tilted screen while using the device or
after changing screen resolution, press the
AUTO function button to improve resolution.
(Only supported in Analog Mode)
2011-04-05 �� 1:20:38
12
CUSTOMIZING SETTINGS
CUSTOMIZING SETTINGS
ENGLISH
ENG
Accessing The Main Menus
1 Press any button on the front of the Monitor set to display the MONITOR SETUP OSD menu.
2 Press the desired menu item.
3 Change the value of the menu item by pressing the buttons on the front of the Monitor set.
To return to the upper menu or set other menu items, use the up arrow (
) button.
4 Select EXIT to leave the OSD menu.
Monitor set Buttons
MENU (See p.13)
Sets the screen options.
AUTO (See p.5)
Optimizes the resolution.
EXIT
Exits the OSD menu.
MONITOR SETUP
MENU
3D (See p.14)
Sets the 3D mode.
3D
AUTO
VOLUME
INPUT
VOLUME (See p.14)
Sets the volume.
EXIT
INPUT
Sets the external input.
NOTE
Different menu items are enabled depending on the type of input signal.
D-SUB / DVI Mode: MENU, 3D, AUTO, INPUT, EXIT
yy
HDMI Mode: MENU, 3D, VOLUME, INPUT, EXIT
yy
ENG.indd 12
2011-04-05 �� 1:20:39
13
CUSTOMIZING SETTINGS
Customizing Settings
MENU
1 Press any button on the front of the Monitor set to display the
MONITOR SETUP OSD menu.
2 Press the MENU button to display the options in the OSD
menu.
3 Set the options by pressing the buttons on the front of the
Monitor set.
4 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu items, use the
up arrow ( ) button.
BRIGHTNESS
ORIGINAL RATIO
3D COLOR EFFECT
COLOR TEMP
PRESET
RED
GREEN
BLUE
CONTRAST
BLACK LEVEL
LANGUAGE
SUPER ENEYGY SAVING
FACTORY RESET
100
WIDE
OFF
PRESET
WARM
ENG
ENGLISH
Menu Settings
50
50
50
70
HIGH
ENGLISH
NO
EXIT
The available program settings are described below.
Menu
BRIGHTNESS
Analog
Digital
HDMI
●
●
●
ORIGINAL RATIO
Description
Adjusts the brightness of the screen.
WIDE
Switch to full screen mode according to input image signal.
3D COLOR
EFFECT
●
●
●
●
●
●
COLOR TEMP
ORIGINAL
Change the input image signal ratio to original.
* This function works only if input resolution is lower than Monitor
set ratio (16:9).
The picture quality is optimized at the 3D mode.
PRESET
●
●
●
Select the screen color.
yy WARM: Set the screen to warm color temperature (more red).
yy MEDIUM: Set the screen to medium color temperature.
yy COOL: Set the screen to cool color temperature (More blue).
USER
yy RED: Set your own red color levels.
yy GREEN: Set your own green color levels.
yy BLUE: Set your own blue color levels.
CONTRAST
●
●
BLACK LEVEL
(Only supported
in HDMI mode)
●
Adjusts the contrast of the screen.
●
You can set the offset level. If you select 'HIGH', the screen will be bright and if you select ‘LOW’, the screen will be dark.
yy Offset: As the criteria for video signal, it is the darkest screen
the monitor can show.
Changes the menu language.
LANGUAGE
●
●
●
SUPER ENERGY
SAVING
●
●
●
FACTORY
●
●
●
Sets the SUPER ENERGY SAVING function.
Returns the monitor to original factory settings.
Analog: D-SUB(Analog signal) input.
yy
Digital: DVI-D(Digital signal) input.
yy
HDMI: HDMI(Digital signal) input.
yy
ENG.indd 13
2011-04-05 �� 1:20:39
14
CUSTOMIZING SETTINGS
3D Settings(Only 3D mode)
3D
ENGLISH
ENG
1 Press any button on the front of the Monitor set to display the
MONITOR SETUP OSD menu.
3D MODE
OFF(1/4)
3D L/R CHANGE
R-L(1/2)
3D - > 2D
OFF
2 Press the 3D button to display the options in the OSD menu.
EXIT
3 Set the options by pressing the buttons on the front of the
Monitor set.
4 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu items, use the
up arrow ( ) button.
The available picture settings are described below.
Menu
3D MODE
3D L/R CHANGE
3D - > 2D
Description
Select the format of 3D video data. (Enabled only for HDMI VIDEO TIMING)
SIDE BY SIDE
Left and right pictures are arranged in Side by Side layout.
TOP & BOTTOM
Left and right pictures are arranged in Top and Bottom layout.
LINE INTERLACED
Left and right pictures are arranged in line by line.
OFF
Turns off 3D Mode.
Changes which frame is shown to each eye.
R-L
Odd lines are Right picture and even lines are Left picture.
L-R
Odd lines are Left picture and even lines are Right picture.
Converts 3D images into 2D. (Enabled only for HDMI VIDEO TIMING)
OFF
Displays images in 3D.
ON
Displays images in 2D.
NOTE
3D Mode.
yy
SIDE BY SIDE
TOP & BOTTOM
LINE INTERLACED
If the 3D option selected is incorrect, images may not be displayed properly.
yy
Volume Settings (Only supported in HDMI)
VOLUME
1 Press any button on the front of the Monitor set to display the
50
MONITOR SETUP OSD menu.
2 Press the VOLUME button to display the options in the OSD
menu.
EXIT
3 Set the options by pressing the buttons on the front of the
Monitor set.
4 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu items, use the up
arrow ( ) button.
ENG.indd 14
2011-04-05 �� 1:20:42
CUSTOMIZING SETTINGS
SUPER ENERGY SAVING Settings
15
SUPER ENERGY SAVING
ENG
ENGLISH
1 Press any button on the front of the Monitor set to
display the MONITOR SETUP OSD menu.
ON
2 Press the MENU button to display the options in the
OSD menu.
3 Select SUPER ENERGY SAVING by pressing the
buttons on the front of the Monitor set and set the
options.
OFF
RESET
SUPER
SAVING
: 5 W/h
TOTAL POWER REDUCTION: 20 W
LED
SAVING
: 12 W/h
TOTAL CO2 REDUCTION: 4 Select EXIT to leave the OSD menu.
OK
16 g
EXIT
To return to the upper menu or set other menu items,
use the up arrow ( ) button.
The available picture settings are described below.
Menu
Description
ON
Enables SUPER ENERGY SAVING you can save energy with this energy-efficient function.
OFF
Disables SUPER ENERGY SAVING.
RESET
Resets the values of total energy consumption reduction and CO2 emission reduction estimates.
NOTE
TOTAL POWER REDUCTION: How much power is saved while using the monitor.
yy
TOTAL CO2 REDUCTION: Change the TOTAL POWER REDUCTION to CO2.
yy
SAVING DATA(W/h)
yy
584 mm (23 inch)
SUPER SAVING
5 W/h
LED SAVING
12 W/h
Saving Data depends on the Panel. So,those values should be different from each panel and panel
yy
vendor.
LG calculated these values by using “broadcast video signal”.
yy
LED Saving refers to how much power can be saved using a WLED Panel instead of CCFL panel.
yy
SUPER SAVING refers to how much power can be saved using the SUPER ENERGY SAVING
yy
function.
ENG.indd 15
2011-04-05 �� 1:20:42
16
TROUBLESHOOTING
ENGLISH
ENG
TROUBLESHOOTING
Check the following before calling for service.
No image appears
Is the power cord of the display
connected?
Is the power indicator light on?
Is the power on and the power
indicator blue or green?
Is the power indicator flickering?
Do you see an "OUT OF RANGE"
message on the screen?
Do you see a "CHECK SIGNAL
CABLE" message on the screen?
yy Check and see if the power cord is connected properly to the power
outlet.
yy Press the Power button.
yy Adjust the brightness and the contrast.
yy If the display is in power saving mode, try moving the mouse or
pressing any key on the keyboard to bring up the screen.
yy Try to turn on the PC.
yy This message appears when the signal from the PC (video card) is
out of horizontal or vertical frequency range of the display. See the
'Specifications' section of this manual and configure your display
again.
yy This message appears when the signal cable between your PC and
your display is not connected. Check the signal cable and try again.
Do you see a "OSD LOCKED" message on the screen?
Do you see “OSD LOCKED” when
you push MENU button?
yy You can secure the current control settings, so that they cannot be
inadvertently changed. You can unlock the OSD controls at any time
by pushing the MENU button for several seconds: the message “OSD
UNLOCKED” will appear.
Display image is incorrect
Display Position is incorrect.
On the screen background, vertical
bars or stripes are visible.
Any horizontal noise appearing in
any image or characters are not
clearly portrayed.
ENG.indd 16
yy Press the AUTO button to automatically adjust your display image to
the ideal setting.
yy Press the AUTO button to automatically adjust your display image to
the ideal setting.
yy Press the AUTO button to automatically adjust your display image to
the ideal setting.
yy Check Control Panel ► Display ► Settings and adjust the display
to the recommended resolution or adjust the display image to the ideal
setting. Set the color setting higher than 24 bits (true color).
2011-04-05 �� 1:20:42
17
TROUBLESHOOTING
CAUTION
ENG
ENGLISH
Check Control Panel ► Display ► Settings and see if the frequency or the resolution were
yy
changed. If yes, readjust the video card to the recommend resolution.
If the recommended resolution (optimal resolution) is not selected, letters may be blurred and the
yy
screen may be dimmed, truncated or biased. Make sure to select the recommend resolution.
The setting method can differ by computer and O/S (Operation System), and resolution mentioned
yy
above may not be supported by the video card performance. In this case, please ask to the computer
or the video card manufacturer.
Display image is incorrect
The screen color is mono or
abnormal.
The screen blinks.
yy Check if the signal cable is properly connected and use a screwdriver
to fasten if necessary.
yy Make sure the video card is properly inserted in the slot.
yy Set the color setting higher than 24 bits (true color) at Control Panel
► Settings.
yy Check if the screen is set to interlace mode and if yes, change it to the
recommend resolution.
Do you see an "Unrecognized monitor, Plug&Play (VESA DDC) monitor found" message?
Have you installed the display
driver?
ENG.indd 17
yy Be sure to install the display driver from the display driver CD (or
diskette) that comes with your display. Or, you can also download the
driver from our web site: http://www.lg.com.
yy Make sure to check if the video card supports Plug&Play function.
2011-04-05 �� 1:20:43
18
TROUBLESHOOTING
ENGLISH
ENG
TROUBLESHOOTING WHEN USING 3D MODE
I can see a swirling oil-like pattern on the monitor when the monitor is turned off.
yy This is caused by the interference of external light in the air layer between the LCD surface and 3D filter.
The pattern becomes almost invisible when you turn on the power again.
I cannot see 3D image properly
yy When you view 3D images with this monitor, it is very important
that you use the glasses provided with the monitor. The glasses are
designed to compensate optically for the 3D filter attached to the
surface of the monitor. If you wear third-party glasses, you may not
see 3D images properly on the monitor.
If you view 3D images outside the
yy The optimal viewing angle of the monitor is 12° in vertical direction
optimal viewing angle or distance,
while 80° in horizontal direction; the optimal viewing distance is
between 50 cm to 90 cm from the monitor.
When you view 3D images outside the optimal viewing angle or
viewing distance, the images may look overlapped or not be displayed
properly in 3D.
If you have not set the resolution,
yy Please set the resolution of the monitor to the maximum (1920 x
1080 @ 60 Hz) in the display settings. The 3D software may not work
properly if the resolution is not set to the maximum.
If the images that your left and right yy The stripe images in the odd-numbered lines are the ones that your
eyes see are reversed,
right eye sees on the monitor. If you only see the stripe images, not
3D images, set the images for your right eye to be displayed in the
odd-numbered lines by changing the player or viewer option of the 3D
software.
I cannot see 3D but only 2D images. yy This monitor works both in 2D and 3D mode. You can view a video in
3D if it is made in 3D. If you try to view 2D images in 3D, they might
not be displayed properly or you may experience poor picture quality.
If the ‘TriDef 3D’ couldn’t work
yy The minimum system requirements on PC to run the ‘TriDef 3D’ :
If you are not using the glasses
provided with the monitor,
properly
ENG.indd 18
»» Intel® Core 2 Duo or AMD Athlon™ 64 X2 Dual-Core CPU or better
»» 1GB RAM
»» NVIDIA® GeForce® 8600 GT or ATI X1650 XT
»» 500MB free disk space
»» Windows® XP (SP2) (32 bit only), Windows® Vista (32 bit only) or
Windows® 7 (32 or 64 bit)
»» DirectX 9.0c compatible sound card
»» Internet connection
»» DVD-ROM drive
»» Network card
»» DirectX 9.0c
2011-04-05 �� 1:20:43
SPECIFICATIONS
19
Display
Screen Type
Weight
3.5 kg
Tilt Range
-5° to 15°
Environmental
conditions
Operating Temperature 10°C to 35 °C
Operating Humidity
20 % to 80 %
Storage Temperature
-10°C to 60 °C
Storage Humidity
5 % to 90 % non-Condensing
Attached ( ), Detached (O)
Wall-outlet type
58.4 cm (23 inch) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
Visible diagonal size: 58.4 cm
Pixel Pitch
0.265 mm x 0.265 mm (Pixel Pitch)
Sync Input
Horizontal Frequency 30 kHz to 83 kHz (Automatic)
Vertical Frequency
56Hz to 75Hz (D-SUB, DVI-D)
56Hz to 61Hz (HDMI)
Input Form
Separate Sync. Digital
Video Input
Signal Input
15 pin D-SUB Connector /DVI-D Connector (Digital)
HDMI Connector
Input Form
RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Resolution
Max
D-SUB(Analog) : 1920 x 1080 @ 60 Hz
DVI / HDMI (Digital) : 1920 x 1080 @ 60 Hz
Recommend
VESA 1920 x 1080 @ 60 Hz
Plug & Play
DDC 2B(Analog,Digital,HDMI)
Power Consumption
On Mode : 39 W(Typ.)
Sleep Mode ≤ 0.5 W
Off Mode ≤ 0.5 W
Power Input
AC 100-240 V~ 50 / 60 Hz 1.0 A
Dimensions
With Stand
54.6 cm x 40.7 cm x 17.9 cm
(Width x Height x Depth) Without Stand
54.6 cm x 34.2 cm x 5.7 cm
Stand Base
Power cord
ENG
ENGLISH
SPECIFICATIONS
Product specifications shown above may be changed without prior notice due to upgrade of product
functions.
ENG.indd 19
2011-04-05 �� 1:20:43
20
SPECIFICATIONS
Preset Modes (Resolution)
ENGLISH
ENG
Display Modes (Resolution)
Horizontal
Frequency(kHz)
Vertical
Frequency(Hz)
Polarity(H/V)
720 x 400
31.468
70
-/+
640 x 480
31.469
60
-/-
640 x 480
37.500
75
-/-
800 x 600
37.879
60
+/+
800 x 600
46.875
75
+/+
1024 x 768
48.363
60
-/-
1024 x 768
60.123
75
+/+
1152 x 864
67.500
75
+/+
1280 x 1024
63.981
60
+/+
1680 x 1050
65.290
60
-/+
1920 x 1080
67.500
60
+/+
Recommend Mode
HDMI 3D TIMING
3D Format
Resolution
Refresh Rate
Frame Packing
1080 p
24 Hz
Frame Packing
720 p
50/60 Hz
Side-by-Side(Half)
1080 p
50/60 Hz
Side-by-Side(Half)
1080 i
50/60 Hz
Side-by-Side(Half)
720 p
50/60 Hz
Top-and-Bottom
1080 p
50/60 Hz
Top-and-Bottom
1080 p
24 Hz
Top-and-Bottom
720 p
50/60 Hz
Limitation
Indicator
ENG.indd 20
Mode
LED Color
On Mode
Blue
Sleep Mode
Blinking Blue
Off Mode
Off
2011-04-05 �� 1:20:43
21
PRECAUTIONS TO TAKE WHEN VIEWING 3D IMAGES
1 If you view images in the 3D mode for a long period of time (playing games, watching movies etc.), you
ENG
ENGLISH
PRECAUTIONS TO TAKE WHEN VIEWING 3D
IMAGES
may feel dizzy. We strongly recommend you to take a rest after one hour of viewing 3D. (The time of
experiencing dizziness varies depending on the individual.)
2 Please view 3D images at the optimal viewing angle and at the recommended distance from the
product. Otherwise, 3D images may appear to be overlapped or may not be displayed properly.
3 If you view 3D images too closely for a long period of time, this may result in dizziness or blurred vision.
Please use the device at the recommended distance.
4 If you are pregnant, elderly or have heart problems, we recommend that you do not view 3D images.
This is because the 3D images can cause disorientation and confusion.
5 3D images can also cause nausea or vomiting for users under the influence of alcohol. In this situation,
please do not view 3D images.
6 Parents/guardians should monitor children’s viewing of 3D images because they may not be used to the
3D viewing experience and lack knowledge on how to handle potential risks.
7 Do not use the 3D glasses as regular glasses, sunglasses or goggles. This may cause your vision to
worsen.
8 Do not keep the 3D glasses in an extremely hot or cold place. This may the shape of the glasses to
change and become damaged. Do not use the 3D glasses if they are damaged because this may cause
your vision to worsen, or you may experience dizzin.
9 The lenses of the 3D glasses (polarizing film) are easily scratched. Use a soft clean cloth when cleaning
them. Do not use any chemical cleaning products on the glasse.
CAUTION
Warning about photosensitivity seizures
Some users may have a seizure or other abnormal symptoms when they are exposed to a
yy
flashing light or particular pattern in a video game or movie. If anyone in your family has a history
of epilepsy or has ever experienced any kind of seizure, please consult with your doctor before
viewing 3D images. If you exhibit any of the symptoms listed below when viewing 3D images,
please stop viewing immediately and consult with your doctor even if you do not have previous
medical problems of this nature.
Symptoms
Dizziness, blurred vision or facial tics, involuntary movements, twitching, blackouts, confusion,
yy
disorientation and wrong state.
To prevent a photosensitivity seizure, please follow the instructions below.
Do not view 3D images when you are tired or ill.
yy
Do not view 3D images for a long period of time.
yy
Reduce the depth of the 3D image.
yy
ENG.indd 21
2011-04-05 �� 1:20:43
22
PROPER POSTURE
ENGLISH
ENG
PROPER POSTURE
Proper posture for using the Monitor set.
50 cm to 90 cm
Adjust your distance from the Monitor
set to allow you to view images from
the optimal distance (L).
Adjust the
Monitor set and
your posture to
allow you to view
images at the
optimal viewing
angle (D).
Adjust the location of the
Monitor set to avoid it
reflecting light.
Place your hands
gently on the
keyboard, keeping
your arms bent at
the elbows and
horizontally outright.
Mode
Size(Inch)
When viewing 3D images
58.4 cm
Optimal viewing distance (L) Optimal viewing angle (D)
50 cm to 90 cm
12°
Precautions to take when viewing 3D images
Wear the 3D glasses provided with the Monitor set.
yy
Watch your posture.
yy
Remain at the optimal distance and angle when viewing 3D images.
yy
(Viewing 3D images too closely may cause your vision to worsen, or you may experience dizziness.)
ENG.indd 22
2011-04-05 �� 1:20:43
ENG.indd 23
2011-04-05 �� 1:20:43
Make sure to read the Safety Precautions before
using the product.
Keep the Owner’s Manual (CD) in an accessible
place for future reference.
The model and serial number of the SET is
located on the back and one side of the SET.
Record it below should you ever need service.
MODEL
SERIAL
ENG.indd 24
ENERGY STAR is a set of power-saving
guidelines issued by the U.S.Environmental
Protection Agency(EPA).
As an ENERGY STAR Partner LGE
U. S. A.,Inc. has determined that this
product meets the ENERGY STAR
guidelines for energy efficiency.
2011-04-05 �� 1:20:43
Download PDF

advertising