LG | IPS225P-BN | LG IPS225P-BN Owner’s Manual

ENGLISH
OWNER’S MANUAL
LCD MONITOR
Please read this manual carefully before operating
your set and retain it for future reference.
LCD MONITOR MODEL
IPS225P
IPS235P
www.lg.com
2
TABLE OF CONTENTS
CONTENTS
ENGLISH
ENG
3
ASSEMBLING AND PREPARING
21 TROUBLESHOOTING
3
Unpacking
4
Parts and buttons
23 SPECIFICATIONS
6
Setting up the Monitor set
6
- Attaching the Stand Base
6
- Detaching the Stand Base
7
- Mounting on a table
9
- Using the Pivot function
10
- Mounting on a wall
11
USING THE MONITOR SET
11
Connecting to a PC
11
- D-SUB connection
11
- DVI-D connection
11
- HDMI connection
13 CUSTOMIZING SETTINGS
13
Accessing The Main Menus
14
Customizing Settings
14
- Menu Settings
15
-PICTURE
16
-COLOR
17
-DISPLAY
17
-VOLUME
18
-OTHERS
19
MODE Setting
20
DUAL PACKAGE Setting
23
IPS225P
24
IPS235P
25
Preset Modes (Resolution)
25
Indicator
ASSEMBLING AND PREPARING
3
ASSEMBLING AND PREPARING
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual product
and accessories.
CD(Owner's Manual) /
Card
D-SUB Cable
(This signal cable may be attached
to this product before shipping out.)
Stand Base
Power Cord
DVI-D Cable
(This cable is not included in all
countries.)
Display Quality Assurance Report
CAUTION
Do not use any unapproved accessories to ensure the safety and product life span.
yy
Any damages or injuries by using unapproved accessories are not covered by the warranty.
yy
NOTE
The accessories supplied with your product may vary depending on the model.
yy
Product specifications or contents in this manual may be changed without prior notice due to upgrade
yy
of product functions.
User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferrite cores
yy
(core in the connector) to maintain standard compliance for the product.
ENG
ENGLISH
Unpacking
4
ASSEMBLING AND PREPARING
Parts and buttons
ENGLISH
ENG
Power Indicator
yyLighting On: Turned on
yyLighting Off: Turned off
(Power Button)
Button (See p.13)
Connection panel (See p.11)
ASSEMBLING AND PREPARING
Button
Description
Accesses the main menus.(See p.13)
OSD LOCKED/
UNLOCKED
This function allows you to lock the current control settings, so
that they cannot be inadvertently changed.
Press and hold the MENU button for several seconds.
The message "OSD LOCKED" should appear.
You can unlock the OSD controls at any time by pushing
the MENU button for several seconds. The message "OSD
UNLOCKED" should appear.
MODE
Use this button to enter USER, MOVIE,TEXT,PHOTO,sRGB menus.(See p.19)
DUAL
Use this button to enter DUAL MONITOR and DUAL WEB menus.(See p.20)
AUTO
When adjusting your display settings, always press the AUTO button on the MONITOR
SETUP OSD. (Only supported in Analog Mode)
The best display mode 1920 x 1080
INPUT
You can choose the input signal.
• When two input signals are connected, you can select the input signal (D-SUB/DVI/
HDMI) you want.
• When only one signal is connected, it is automatically detected. The default setting is
D-SUB.
EXIT
Exit the OSD(On Screen Display).
(Power Button)
Turns the power on or off.
Power Indicator
The power indicator stays blue if the display is running
properly (On Mode). If the display is in Sleep Mode, the power
indicator blinks blue.
ENG
ENGLISH
MENU
5
6
ASSEMBLING AND PREPARING
ENGLISH
ENG
Setting up the Monitor set
Detaching the Stand Base
Attaching the Stand Base
1 Place the Monitor set with the screen side
down on a flat and cushioned surface.
1 Place the Monitor set with the screen side
down on a flat and cushioned surface.
CAUTION
Lay a foam mat or soft protective cloth
on the surface to protect the screen from
damage.
2 Turn the screw to the left with a Coin, and then
pull out the Stand Base from the Stand Body.
2 Attach the Stand Base and then tighten the
screw to the right with a Coin.
Stand Base
1
Stand Base
CAUTION
This illustration depicts the general model of
yy
connection. Your monitor may differ from the
items shown in the picture.
Do not carry the product upside down holding
yy
only the stand base. The product may fall
and get damaged or injure your foot.
7
ASSEMBLING AND PREPARING
Mounting on a table
NOTE
position on a table.
Tilt from +15 to -5 degrees up or down to adjust
the angle of the Monitor set to suit your view.
-5
Leave a 10 cm (minimum) space from the wall
for proper ventilation.
15
10 cm
10 cm
10 cm
10 cm
Front
Rear
• Swivel Range : -45°~45°(+/- 2°) 2 Connect the Power Cord to a wall outlet.
-45° ~ 45°(+/- 2°)
• Height Range : maximum 5.12 inch (130.0 mm) 130.0 mm
3 Press (Power) button on the bottom switch
panel to turn the power on.
CAUTION
Unplug the power cord before moving the
Monitor to another location. Otherwise electric
shock may occur.
* Please be sure to
remove the Locking pin
to adjust the height.
ENG
ENGLISH
1 Lift and tilt the Monitor set into its upright
8
ASSEMBLING AND PREPARING
Using the Kensington security system
WARNING
ENGLISH
ENG
The Kensington security system connector is
located at the back of the Monitor set. For more
information of installation and using, refer to the
manual supplied with the Kensington security
system or visit http://www.kensington.com .
• When adjusting the angle of
the screen, do not put your
finger(s) in between the head
of the monitor and the stand
body. You can hurt your
finger(s).
Connect the Kensington security system cable
between the Monitor set and a table.
• When adjusting the height
of the screen, do not put
your finger(s) in between the
head of the monitor and the
stand base. You can hurt your
finger(s).
WARNING
• You do not need to replace the Locking pin after
it is removed,to adjust its height.
NOTE
The Kensington security system is optional.
You can obtain it from most electronics stores.
ERGONOMIC
• It is recommended that in order to maintain an
ergonomic and comfortable viewing position,
the forward tilt angle of the monitor should not
exceed 5 degrees.
ASSEMBLING AND PREPARING
9
Using the Pivot function
1. Lift the monitor to its highest height to utilize the Pivot function.
2. Landscape & Portrait : You can rotate the panel 90°clockwise.
Please be cautious and avoid contact between the monitor head and the Stand Base when rotating
the screen to access the Pivot function. If the monitor head touches the Stand Base, then the Stand
Base could crack.
Head section
.......
Stand section
.....
3. Be careful with the cables when rotating the screen.
ENG
ENGLISH
- The pivot function allows you to rotate the screen 90 degrees clockwise.
10
ASSEMBLING AND PREPARING
Mounting on a wall
Model
ENGLISH
ENG
For proper ventilation, allow a clearance of 10 cm
on each side and from the wall. Detailed
instructions are available from your dealer, see the
optional Tilt Wall Mounting Bracket Installation and
Setup Guide.
IPS225P/IPS235P
VESA (A x B)
Standard screw
Number of screws
VESA (A x B)
B
10 cm
10 cm
100 x 100
M4
4
A
10 cm
10 cm
CAUTION
If you intend to mount the Monitor set to a wall,
attach Wall mounting interface (optional parts) to
the back of the set.
When you install the Monitor set using a wall
mounting interface (optional parts), attach it
carefully so it will not drop.
1 Please, Use the screw and wall mount interface
in accordance with VESA Standards.
2 If you use screw longer than standard, the
Disconnect the power cord first, and then
yy
move or install the Monitor set. Otherwise
electric shock may occur.
If you install the Monitor set on a ceiling or
yy
slanted wall, it may fall and result in severe
injury.
Use only an authorized LG wall mount
yy
and contact the local dealer or qualified
personnel.
Do not over tighten the screws as this may
yy
cause damage to the Monitor set and void
your warranty.
Use only screws and wall mounts that
yy
meet the VESA standard. Any damages
or injuries by misuse or using an improper
accessory are not covered by the warranty.
monitor might be damaged internally.
3 If you use improper screw, the product might be
damaged and drop from mounted position. In
this case, LG Electronics is not responsible for
it.
4 VESA compatible.
5 Please use VESA standard as below.
784.8 mm (30.9 inch) and under
yy
* Wall Mount Pad Thickness : 2.6 mm
* Screw : Φ 4.0 mm x Pitch 0.7 mm x
Length 10 mm
787.4 mm (31.0 inch) and above
yy
* Please use VESA standard wall mount pad
and screws.
NOTE
Use the screws that are listed on the VESA
yy
standard screw specifications.
The wall mount kit will include an installation
yy
manual and necessary parts.
The wall mount bracket is optional. You can
yy
obtain additional accessories from your local
dealer.
The length of screws may differ depending
yy
on the wall mount. Be sure to use the proper
length.
For more information, refer to the
yy
instructions supplied with the wall mount.
USING THE MONITOR SET
11
USING THE MONITOR SET
Your Monitor set supports Plug & Play*.
yy
*Plug & Play: A PC recognizes a connected
device that users connect to a PC and turn
on, without device configuration or user
intervention.
DVI-D connection
Transmits a digital video signal from your PC to
the Monitor set. Connect the PC and the Monitor
set with a DVI cable as shown in the following
illustrations.
D-SUB connection
Transmits analog video from your PC to the
Monitor set. Connect the PC and the Monitor set
with the supplied D-sub 15 pin signal cable as
shown in the following illustrations.
HDMI connection
Transmits the digital video and audio signals from
your PC or A/V to the Monitor set. Connect the PC
or A/V and the Monitor set with the HDMI cable as
shown in the following illustrations.
NOTE
When using a D-Sub signal input cable
yy
connector for Macintosh
Mac adapter
yy
For Apple Macintosh use, a separate plug
adapter is needed to change the 15 pin
high density (3 row) D-SUB VGA connector
on the supplied cable to a 15 pin 2 row
connector.
NOTE
If you use HDMI PC, it can cause compatibility
yy
problem.
ENG
ENGLISH
Connecting to a PC
12
USING THE MONITOR SET
CAUTION
ENGLISH
ENG
Connect the signal
yy
input cable and tighten
it by turning the screws
clockwise.
Do not press the screen with your finger for yy
a long time as this may result in temporary
distortion on the screen.
Avoid displaying a fixed image on the
yy
screen for a long period of time to prevent
image burn. Use a screensaver if possible.
NOTE
When you want to use two PC in our Monitor,
yy
please connect the signal cable(D-SUB/
DVI-D/HDMI) respectively in Monitor set.
If you turn the Monitor set on while it is cold,
yy
the screen may flicker. This is normal.
Some red, green, or blue spots may appear
yy
on the screen. This is normal.
Self Image Setting Function
Press the power button on the bottom panel to
turn the power on. When monitor power is turned
on, the "Self Image Setting" Function is executed
automatically. (Only supported in Analog Mode)
NOTE
"Self Image Setting" Function.
yy
This function provides the user with optimal
display settings.When the user connects
the monitor for the first time, this function
automatically adjusts the display to optimal
settings for individual input signals.(Only
supported in Analog Mode)
‘AUTO’ Function.
yy
When you encounter problems such as
blurry screen, blurred letters, screen flicker
or tilted screen while using the device or
after changing screen resolution, press the
AUTO function button to improve resolution.
(Only supported in Analog Mode)
CUSTOMIZING SETTINGS
13
CUSTOMIZING SETTINGS
ENG
ENGLISH
Accessing The Main Menus
1 Press any button on the bottom of the Monitor set to display the MONITOR SETUP OSD menu.
2 Press the desired menu item.
3 Change the value of the menu item by pressing the buttons on the bottom of the Monitor set.
To return to the upper menu or set other menu items, use the up arrow (
) button.
4 Select EXIT to leave the OSD menu.
Monitor set Buttons
MENU (See p.14)
Sets the screen options.
DUAL (See p.20)
Sets the screen.
EXIT
Exits the OSD menu.
MODE (See p.19)
Sets the mode.
AUTO (See p.12)
Optimizes the resolution.
INPUT
Sets the external input.
14
CUSTOMIZING SETTINGS
Customizing Settings
ENGLISH
ENG
Menu Settings
1 Press any button on the bottom of the Monitor set to display
the MONITOR SETUP OSD menu.
2 Press the MENU button to display the options in the OSD
menu.
3 Set the options by pressing the buttons on the bottom of the
Monitor set.
4 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu items, use the
up arrow ( ) button.
The available program settings are described below.
Menu
PICTURE
Sub-menu
BRIGHTNESS
CONTRAST
SHARPNESS
Analog Digital HDMI
●
●
BLACK LEVEL
COLOR
Description
●
To adjust the brightness, contrast and sharpness of the
screen
●
To set offset level
●
To customize the color of the screen
COLOR TEMP
(PRESET/USER)
GAMMA
●
●
COLOR RESET
DISPLAY
HORIZONTAL
VERTICAL
●
CLOCK PHASE
●
To adjust the position of the screen
OVERSCAN
●
VOLUME
OTHERS
●
LANGUAGE
POWER INDICATOR
●
WHITE BALANCE
●
ORIGINAL RATIO
●
●
●
●
●
SUPER ENERGY
SAVING
●
●
●
FACTORY RESET
●
●
●
Analog: D-SUB(Analog signal) input.
yy
Digital: DVI-D(Digital signal) input.
yy
HDMI: HDMI(Digital signal) input.
yy
To improve the clarity and stability of the screen
To adjust the volume
To customize the screen status for a user's operating
environment
CUSTOMIZING SETTINGS
15
PICTURE
the MONITOR SETUP OSD menu.
2 Press the MENU button to display the options in the OSD
menu.
3 Select PICTURE by pressing the buttons on the bottom of
the Monitor set and set the options.
4 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu items, use
the up arrow ( ) button.
The available picture settings are described below.
Menu
Description
BRIGHTNESS
To adjust the brightness of the screen.
CONTRAST
To adjust the contrast of the screen.
SHARPNESS
To adjust the clearness of the screen.
BLACK LEVEL
You can set the offset level. If you select'HIGH', the screen will be bright and if you select ‘LOW’,
the screen will be dark. (only for HDMI input)
* Offset?As the criteria for video signal, it is the darkest screen the monitor can show.
ENG
ENGLISH
1 Press any button on the bottom of the Monitor set to display
16
CUSTOMIZING SETTINGS
COLOR
ENGLISH
ENG
1 Press any button on the bottom of the Monitor set to
display the MONITOR SETUP OSD menu.
2 Press the MENU button to display the options in the OSD
menu.
3 Select COLOR by pressing the buttons on the bottom of
the Monitor set and set the options.
4 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu items, use
the up arrow ( ) button.
The available picture settings are described below.
Menu
COLOR TEMP
Description
PRESET
Select the screen color. • WARM: Set the screen to warm color temperature (more red). • MEDIUM: Set the screen to medium color temperature. • COOL: Set the screen to cool color temperature (more blue).
USER
• SIX COLOR:
Sets and stores the hue and saturation for six colors(RED/ GREEN/BLUE/
CYAN/MAGENTA/YELLOW) to satisfy the color requirements of a user. Adjusts the screen hue.
HUE SATURATION Adjusts the color sharpness on the screen. Lower values make
the color sharpness weaker and colors lighter while higher
values make the color sharpness stronger and colors dark.
• RED:
• GREEN:
• BLUE:
Set your own red color levels.
Set your own green color levels.
Set your own blue color levels.
GAMMA
Set your own gamma value. : 1.8/2.0/2.2/2.4/2.6 On the monitor. Image is adjusted according to
different gamma curve.
COLOR RESET
Resets the color settings to the factory default settings for the current input device. CUSTOMIZING SETTINGS
17
DISPLAY
the MONITOR SETUP OSD menu.
2 Press the MENU button to display the options in the OSD
menu.
3 Select DISPLAY by pressing the buttons on the bottom of
the Monitor set and set the options.
4 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu items, use
the up arrow ( ) button.
The available picture settings are described below.
Menu
Description
HORIZONTAL
To move image left and right.
VERTICAL
To move image up and down.
CLOCK
To minimize any vertical bars or stripes visible on the screen background.The horizontal screen
size will also change.
PHASE
To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or
sharpen the image of characters.
OVERSCAN
To select the range of output image for DTV timing in HDMI input.(only for HDMI input)Recommend
overscan function to turn on when connect AV equipment.
VOLUME
1 Press any button on the bottom of the Monitor set to display
the MONITOR SETUP OSD menu.
2 Press the MENU button to display the options in the OSD
menu.
3 Select VOLUME by pressing the buttons on the bottom of
the Monitor set and set the options.
4 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu items, use
the up arrow ( ) button.
The available picture settings are described below.
Menu
VOLUME
Description
To adjust the volume of headphone/Earphone.(Only for HDMI input)
ENG
ENGLISH
1 Press any button on the bottom of the Monitor set to display
18
CUSTOMIZING SETTINGS
OTHERS
ENGLISH
ENG
1 Press any button on the bottom of the Monitor set to display the
MONITOR SETUP OSD menu.
2 Press the MENU button to display the options in the OSD menu.
3 Select OTHERS by pressing the buttons on the bottom of the
Monitor set and set the options.
4 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu items, use the up
arrow ( ) button.
The available picture settings are described below.
Menu
Description
LANGUAGE
To choose the language in which the control names are displayed.
POWER
INDICATOR
Use this function to set the power indicator on the bottom side of the monitor to ON or OFF.If you
set OFF, it will go off.
If you set ON at any time, the power indicator will automatically be turned on.
WHITE
BALANCE
If the output of the video card is different the required specifications,the color level may deteriorate
due to video signal distortion. Using this function, the signal level is adjusted to fit into the standard
output level of the video card in order to provide the optimal image.Activate this function when
white and black colors are present in the screen.
ORIGINAL RATIO WIDE
Switch to full screen mode according to input image signal.
ORIGINAL
Change the input image signal ratio to original.
* This function works only if input resolution is lower than Monitor set ratio (16:9).
SUPER ENERGY Sets the SUPER ENERGY SAVING function.
SAVING
ON
Enables SUPER ENERGY SAVING you can save energy with this energy- efficient function
OFF
Disables SUPER ENERGY SAVING.
RESET
Resets the values of total energy consumption reduction and CO2 emission reduction
estimates.
RTC (Response
Time Compensation)
If you enable RTC function, you can control Response Time Compensation level.
If you set OFF,you disenable the Response Time Compensation function.
FACTORY
RESET
Restore all factory default settings except"LANGUAGE." Press the ◄, ► buttons to reset
immediately.
NOTE
TOTAL POWER REDUCTION: How much power is saved while using the monitor.
yy
TOTAL CO2 REDUCTION: Change the TOTAL POWER REDUCTION to CO2.
yy
SAVING DATA(W/h)
yy
545 mm (21.5 inch) 584 mm (23 inch)
SUPER SAVING
4 W/h
5 W/h
LED SAVING
15 W/h
12 W/h
Saving Data depends on the Panel. So,those values should be different from each panel and panel
yy
vendor.
LG calculated these values by using “broadcast video signal”.
yy
LED Saving refers to how much power can be saved using a WLED Panel instead of CCFL panel.
yy
SUPER SAVING refers to how much power can be saved using the SUPER ENERGY SAVING
yy
function.
CUSTOMIZING SETTINGS
19
MODE Setting
2 Press the MODE button to display the options in the OSD menu.
3 Set the options by pressing the buttons on the bottom of the Monitor set.
4 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu items, use the up arrow (
) button.
The available picture settings are described below.
Menu
Description
USER
It is a mode that the user can adjust each element. It can adjust the color mode of the Main Menu.
MOVIE
It is a mode that the screen is adjusted to the best to view the videos.
TEXT
It is a mode that the screen is adjusted to the best for the text works.
PHOTO
It is a mode that the screen is adjusted to the best to view pictures.
sRGB
It is a mode that the screen is adjusted to the standard sRGB.
ENG
ENGLISH
1 Press any button on the bottom of the Monitor set to display the MONITOR SETUP OSD menu.
20
CUSTOMIZING SETTINGS
DUAL PACKAGE Setting
ENGLISH
ENG
* Before using below functions, please install DUAL PACKAGE programme.
1 Press any button on the bottom of the Monitor set to
display the MONITOR SETUP OSD menu.
2 Press the DUAL button to display the options in the
OSD menu.
3 Set the options by pressing the buttons on the bottom
of the Monitor set.
4 Select EXIT to leave the OSD menu.
To return to the upper menu or set other menu items,
use the up arrow ( ) button.
The available picture settings are described below.
Menu
DUAL MONITOR
DUAL WEB
Description
OFF
If select OFF,DUALMONITOR off
EXTENDED
By selecting EXTENDED,user can use secondary monitor as extended mode of
primary monitor.
CLONE
By selecting CLONE,user can use secondary monitor as done mode of primary
monitor.
ON
Help user to browse web efficiently by dividing in half. Help to arrange and
move windows on screen. Help user to control divided windows ratio.
OFF
If select OFF,DUAL WEB is off.
NOTE
When monitor goes to Power Saving Mode with PC power saving option, on pressing any button and
yy
selecting Dual option user can bring back monitor to normal mode.
TROUBLESHOOTING
21
Check the following before calling for service.
No image appears
Is the power cord of the display
connected?
Is the power indicator light on?
Is the power on and the power
indicator blue or green?
Is the power indicator flickering?
Do you see an "OUT OF RANGE"
message on the screen?
Do you see a "CHECK SIGNAL
CABLE" message on the screen?
yy Check and see if the power cord is connected properly to the power
outlet.
yy Press the Power button.
yy Adjust the brightness and the contrast.
yy If the display is in power saving mode, try moving the mouse or
pressing any key on the keyboard to bring up the screen.
yy Try to turn on the PC.
yy This message appears when the signal from the PC (video card) is
out of horizontal or vertical frequency range of the display. See the
'Specifications' section of this manual and configure your display
again.
yy This message appears when the signal cable between your PC and
your display is not connected. Check the signal cable and try again.
Do you see a "OSD LOCKED" message on the screen?
Do you see “OSD LOCKED” when
you push MENU button?
yy You can secure the current control settings, so that they cannot be
inadvertently changed. You can unlock the OSD controls at any time
by pushing the MENU button for several seconds: the message “OSD
UNLOCKED” will appear.
Display image is incorrect
Display Position is incorrect.
On the screen background, vertical
bars or stripes are visible.
Any horizontal noise appearing in
any image or characters are not
clearly portrayed.
yy Press the AUTO button to automatically adjust your display image to
the ideal setting.
y
y Press the AUTO button to automatically adjust your display image to
the ideal setting.
yy Press the AUTO button to automatically adjust your display image to
the ideal setting.
yy Check Control Panel ► Display ► Settings and adjust the display
to the recommended resolution or adjust the display image to the
ideal setting. Set the color setting higher than 24 bits (true color).
ENG
ENGLISH
TROUBLESHOOTING
22
TROUBLESHOOTING
CAUTION
ENGLISH
ENG
Check Control Panel ► Display ► Settings and see if the frequency or the resolution were
yy
changed. If yes, readjust the video card to the recommend resolution.
If the recommended resolution (optimal resolution) is not selected, letters may be blurred and the
yy
screen may be dimmed, truncated or biased. Make sure to select the recommend resolution.
The setting method can differ by computer and O/S (Operation System), and resolution mentioned
yy
above may not be supported by the video card performance. In this case, please ask to the computer
or the video card manufacturer.
Display image is incorrect
The screen color is mono or
abnormal.
The screen blinks.
yy Check if the signal cable is properly connected and use a screwdriver
to fasten if necessary.
yy Make sure the video card is properly inserted in the slot.
yy Set the color setting higher than 24 bits (true color) at Control Panel
► Settings.
yy Check if the screen is set to interlace mode and if yes, change it to
the recommend resolution.
Do you see an "Unrecognized monitor, Plug&Play (VESA DDC) monitor found" message?
Have you installed the display
driver?
yy Be sure to install the display driver from the display driver CD (or
diskette) that comes with your display. Or, you can also download the
driver from our web site: http://www.lg.com.
yy Make sure to check if the video card supports Plug&Play function.
SPECIFICATIONS
23
IPS225P
Display
Screen Type
Weight
5.45 kg
Range
Tilt
-5° to 15°
Swivel
-45° ~ 45°(+/- 2°)
Height
130.0 mm(5.12 inch) 54.5 cm (21.5 inch) Flat Panel Active matrix-TFT
LCDAnti-Glare coating
Visible diagonal size: 54.5 cm
Pixel Pitch
0.247 mm x 0.247 mm (Pixel Pitch)
Sync Input
Horizontal Frequency 30 kHz to 83 kHz (Automatic)
Vertical Frequency
56Hz to 75Hz (D-SUB, DVI-D)
56Hz to 61Hz (HDMI)
Input Form
Separate Sync. Digital
Video Input
Signal Input
15 pin D-SUB Connector /DVI-D Connector (Digital)
HDMI Connector
Input Form
RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Resolution
Max
D-SUB(Analog) : 1920 x 1080 @ 60 Hz
DVI / HDMI (Digital) : 1920 x 1080 @ 60 Hz
Recommend
VESA 1920 x 1080 @ 60 Hz
Plug & Play
DDC 2B(Analog,Digital,HDMI)
Power Consumption
On Mode : 31 W(Typ.)
Sleep Mode ≤ 0.3 W
Off Mode ≤ 0.3 W
Power Input
AC 100-240 V~ 50 / 60 Hz 1.0A
Dimensions
With Stand
51.3 cm x 51.6 cm x 22.2 cm (Max)
(Width x Height x Depth)
51.3 cm x 38.6 cm x 22.2 cm (Min)
Without Stand
51.3 cm x 31.2 cm x 5.9 cm
Environmental
conditions
Stand Base
Power cord
Operating Temperature 10°C to 35 °C
Operating Humidity
10 % to 80 %
Storage Temperature
-20°C to 60 °C
Storage Humidity
5 % to 90 % non-Condensing
Attached ( ), Detached (O)
Wall-outlet type
Product specifications shown above may be changed without prior notice due to upgrade of product
functions.
ENG
ENGLISH
SPECIFICATIONS
24
SPECIFICATIONS
ENGLISH
ENG
‌SPECIFICATIONS
IPS235P
Display
Screen Type
58.4 cm (23 inch) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
Visible diagonal size: 58.4 cm
Sync Input
Pixel Pitch
Horizontal Frequency
Vertical Frequency
0.265 mm x 0.265 mm (Pixel Pitch)
30 kHz to 83 kHz (Automatic)
56Hz to 75Hz (D-SUB, DVI-D)
56Hz to 61Hz (HDMI)
Video Input
Input Form
Signal Input
Separate Sync. Digital
15 pin D-SUB Connector /DVI-D Connector (Digital)
HDMI Connector
Resolution
Input Form
Max
RGB Analog (0.7 Vp-p/ 75 ohm), Digital
D-SUB(Analog) : 1920 x 1080 @ 60 Hz
DVI / HDMI (Digital) : 1920 x 1080 @ 60 Hz
VESA 1920 x 1080 @ 60 Hz
Recommend
Plug & Play
Power Consumption
DDC 2B(Analog,Digital,HDMI)
On Mode : 35 W(Typ.)
Sleep Mode ≤ 0.3 W
Off Mode ≤ 0.3 W
Power Input
AC 100-240 V~ 50 / 60 Hz 1.0 A
With Stand
54.7 cm x 51.6 cm x 22.2 cm (Max)
Dimensions
(Width x Height x Depth)
54.7 cm x 38.6 cm x 22.2 cm (Min)
Without Stand
54.7 cm x 33.1 cm x 5.9 cm
Weight
5.95 kg
Range
Tilt
-5° to 15°
Swivel
-45° ~ 45°(+/- 2°)
Height
130.0 mm(5.12 inch)
Environmental
Operating Temperature 10°C to 35 °C
10 % to 80 %
conditions Operating Humidity
Storage Temperature
-20°C to 60 °C
5 % to 90 % non-Condensing
Storage Humidity
Stand Base
Attached ( ), Detached (O)
Power cord
Wall-outlet type
Product specifications shown above may be changed without prior notice due to upgrade of product
functions.
SPECIFICATIONS
25
Preset Modes (Resolution)
Horizontal
Frequency(kHz)
Vertical
Frequency(Hz)
Polarity(H/V)
720 x 400
31.468
70
-/+
640 x 480
31.469
60
-/-
640 x 480
37.500
75
-/-
800 x 600
37.879
60
+/+
800 x 600
46.875
75
+/+
1024 x 768
48.363
60
-/-
1024 x 768
60.123
75
-/-
1152 x 864
67.500
75
+/+
1280 x 1024
63.981
60
+/+
1280 x 1024
79.976
75
+/+
1680 x 1050
65.290
60
-/+
1920 x 1080
67.500
60
+/+
ENG
ENGLISH
Display Modes (Resolution)
Recommend Mode
HDMI TIMING
Display Modes (Resolution)
Horizontal Frequency(kHz)
Vertical Frequency(Hz)
480P
31.50
60
576P
31.25
50
720P
37.50
50
720P
45.00
60
1080i
28.12
50
1080i
33.75
60
1080P
56.25
50
1080P
67.50
60
Indicator
Mode
LED Color
On Mode
Blue
Sleep Mode
Blinking Blue
Off Mode
Off
Recommend Mode
Make sure to read the Safety Precautions before
using the product.
Keep the Owner’s Manual (CD) in an accessible
place for future reference.
The model and serial number of the SET is
located on the back and one side of the SET.
Record it below should you ever need service.
MODEL
SERIAL
ENERGY STAR is a set of power-saving
guidelines issued by the U.S.Environmental
Protection Agency(EPA).
As an ENERGY STAR Partner LGE
U. S. A.,Inc. has determined that this
product meets the ENERGY STAR
guidelines for energy efficiency.
Download PDF