LG L1750B-BF Owner’s Manual

User's Guide
L1750B
L1950B
Make
sure
to read the
Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for furture reference.
See the label attached
on
the product and
dealer when you ask for service.
give the information to your
This unit has been
engineered and manufactured to ensure your personal
safety, however improper use may result in potential eletrical shock or fire
hazards. In order to allow the proper operation of all safeguards
incorporated in this display, observe the following basic rules for its
installation, use, and servicing.
On
Safety
power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided by the supplier. If the power cable is faulty in any way, please contact the
Use
only the
manufacturer
or
the nearest authorized
repair service provider for a replacement.
The power supply cord is used as the main disconnection device. Ensure that the
socket-outlet is easily accessible after installation.
Operate the display only from a power source indicated in the specifications of
this manual or listed on the display. If you are not sure what type of power supply
you have in your home, consult with your dealer.
Overloaded AC outlets and extension cords
cords and broken
plugs. They
technician for replacement.
Do not
Open
There
the
may result in
are
a
dangerous. So
shock
or
are
frayed
power
fire hazard. Call your service
Display.
serviceable components inside.
There are Dangerous High Voltages inside, even when the power is OFF.
Contact your dealer if the display is not operating properly.
are no user
To Avoid Personal
Injury :
Do not place the display on a sloping shelf unless properly secured.
Use only a stand recommended by the manufacturer.
To Prevent Fire
or
Hazards:
Always turn the display OFF if you leave the room for more than a short period
of time. Never leave the display ON when leaving the house.
Keep children from dropping or pushing objects into the display's cabinet
openings. Some internal parts carry hazardous voltages.
Do not add accessories that have not been designed for this display.
During a lightning storm or when the display is to be left unattended for an
extended period of time, unplug it from the wall outlet.
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not
the display where the power cord is subject to damage.
Do not
use
this
display
sink, laundry tub, in
near water
a wet
such
basement,
as near a
or near a
place
bathtub, washbowl, kitchen
swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.
can cause
strike the Active Matrix LCD with anything hard
damage the Active Matrix LCD permanently.
Do not rub
mar, or
or
Do not press the LCD
some
screen
with your
finger for a long
time
as
as
this may scratch,
this may
cause
afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance.
If
possible, use the recommended resolution to obtain the best image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD panel.
On
Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly
screen because over-spraying may cause electrical shock.
On
on
the
display
Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
On
Disposal
The fluorescent lamp used in this product contains a small amount of mercury.
Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of
your local authority.
the
Connecting
Before
Display
setting up the monitor, ensure that the power to the monitor, the
computer system, and other attached devices is turned off.
Connecting the stand
1.
base
Place the monitor with its front
2. Align the hooks on the stand
3. Insert the hooks into slots.
Warning:
facing
Removing the stand
or
downward
base with the
soft cloth.
on a
matching
base
slots in the base of the monitor.
locking pin may only be removed from those monitors
a standing base when the base is pulled up.
Otherwise, you may be injured by the protruding sections of the stand.
The tape and
equipped with
Hook
Slot
4.
Use
to
a
thumbscrew
on
the back of the stand base and turn the thumbscrew clockwise
tighten.
5. When you
desire to
disintegrate
the monitor from the stand base, turn the thumbscrew
counterclockwise.
Thumbscrew
Important
This illustration
the items
depicts the general
shown in the picture.
model of connection. Your monitor may differ from
Once you connect the stand base, try not to disconnect it.
Do not carry the monitor upside down holding only the stand base. The monitor may
fall and get damaged or injure your foot.
A3
the
Connecting
Before
Display
setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Positioning your display
1. Adjust the position
Tilt
Range
:
of the
panel
in various ways for maximum comfort.
-5˚~25˚
Height Range
:
Swivel
:
350˚
maximun 2.95 inch (75 mm)
75
First,
the
mm
remove
locking pin.
Warning:
When
do not put your finger in between
the head of the monitor and the stand base. You can hurt your finger(s).
adjusting
the size of the
screen
Ergonomic
It is recommended that in order to maintain
viewing position,
degrees.
the forward tilt
angle
an
ergonomic
and comfortable
of the monitor should not exceed 5
A4
Connecting
the
the
Using
Display
Computer
1.
Place the monitor in
3.
connection. 1
Connect the power cord into
convenient, well-ventilated location near your computer.
To adjust height of your monitor, unlock the stand lock on top of the stand.
2. Connect the signal cable. When attached, tighten the thumbscrews to secure the
the
display.
a
a
proper power outlet that is
easily accessible and
close to
2
Signal
Power Cord
Cable
Digital signal Analog signal
DVI
D-sub
Varies according to model.
NOTE
This is
of the
This
a
simplified representation
rear
Wall-outlet type
view.
view
represents a
general model; your display may
rear
differ from the view
as
2
1
shown.
PC-outlet type
PC
PC
MAC
Mac adapter
For Apple Macintosh use,
separate plug adapter is needed to change
the 15 pin high density (3 row) D-sub VGA connector on the supplied
cable to a 15 pin 2 row connector.
4.
Press
button
on
the front switch
panel
to turn the power
When monitor power is turned on, the 'Self
Function' is executed
a
on.
Image Setting
automatically.
(Only Analog Mode)
NOTE
Self Image Setting
'
Function'? This function
provides the user with optimal display settings.When the user
connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual
input signals. If you want to adjust the monitor while in use, or wish to manually run this function once again, push
the 'AUTO/SET' button on the front panel of the monitor. Otherwise, you may execute the Factory reset' option on
the OSD adjustment menu. However, be aware that this option initializes all the menu items except 'Language'.
'
A5
Control Panel Functions
Front Panel Controls
Control
Function
MENU Button
Use this button to enter
or
exit the On Screen
Display.
OSD LOCKED/UNLOCKED
This function allows you to lock the current control
settings, so that they cannot be inadvertently changed.
Press and hold the MENU button for several seconds.
The message "OSD LOCKED" should appear.
You
unlock the OSD controls at any time by pushing
the MENU button for several seconds. The message
can
"OSD UNLOCKED" should appear.
-+
Buttons
Use these buttons to select
Screen
For
SOURCE hot
key
or
adjust functions
Display.
more
information, refer to page
Use this button to make D-Sub
This feature is used when two
to the
in the On
display.
The default
A6
or
A13.
DVI connector active.
computers
setting
are
is D-Sub.
connected
Control Panel Functions
Control
Function
AUTO/SET
Use this button to enter
Button
Display.
a
selection in the On Screen
AUTO IMAGE ADJUSTMENT
When
adjusting
your display settings, always press
the AUTO/SET button before entering the On Screen
Display(OSD). This will automatically adjust your
display image to the ideal settings for the current
screen resolution size (display mode).
The best
display
mode is
17 inch monitor
:
1280
x
1024
19 inch monitor
:
1280
x
1024
Power Button
Use this button to turn the
Power Indicator
This Indicator
display
on or
off.
lights up green when the display
operates normally(On Mode). If the display is in Sleep
Mode (Energy Saving), this indicator color changes
to amber.
A7
On Screen
Screen
Display (OSD) Control Adjustment
Adjustment
Making adjustments to the image size, position and operating parameters of
the display is quick and easy with the On Screen Display Control system.
A short example is given below to familiarize you with the use of the controls.
The following section is an outline of the available adjustments and selections
you can make using the OSD.
NOTE
Allow the
To make
display to
stabilize for at least 30 minutes before
adjustments
in the On Screen
Display, follow these steps:
Press the MENU Button, then the main
To
access a
control,
use
becomes
highlighted,
Use the
-+
/
the
menu
of the OSD appears.
-+
or
Buttons. When the icon you want
press the AUTO/SET Button.
Buttons to
AUTO/SET Button
making image adjustments.
adjust the image
to the desired level. Use the
to select other sub-menu items.
Push the MENU Button
once to return to
the main
menu to
select another
function. Push the MENU Button twice to exit from the OSD.
A8
On Screen
Selection and
Display(OSD)
Adjustment
following table indicates all the On Screen Display control, adjustment,
and setting menus.
The
Main
menu
PICTURE
Sub-menu
AD
Reference
BRIGHTNESS
To
CONTRAST
contrast and gamma of the
adjust the brightness,
screen
GAMMA
COLOR
PRESET
6500K
To customize the color of
9300K
the
screen
RED
GREEN
BLUE
POSITION
TRACKING
SETUP
HORIZONTAL
To
VERTICAL
screen
CLOCK
To
adjust the position
of the
PHASE
improve the clarity
stability of the screen
LANGUAGE
To customize the
screen
status for a user's
operating
OSD
HORIZONTAL
and
environment
POSITION VERTICAL
WHITE BALANCE
POWER INDICATOR
FACTORY RESET
MOVIE / TEXT
FLATRON
F-ENGINE(
-
)
To select
USER
desired
or
customize
image settings
NORMAL
:
A
:
D
:
Adjustable
Analog Input
Digital Input
NOTE
The order of icons may differ
depending
on
A9
the model (A9~A13).
On Screen
Selection and
Display(OSD)
Adjustment
procedure of selecting and adjusting an item
using the OSD system. Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
You
were
introduced to the
Press the MENU
Menu Name
Button, then the main menu of the OSD appears.
PICTURE
Sub-menus
Icons
Button
Tip
MENU
-+
SET
:
:
Exit
Adjust (Decrease/Increase)
:
Enter
:
Select another sub-menu
NOTE
OSD (On Screen
Display)
menu
languages
on
A10
the monitor may differ from the manual.
On Screen
Selection and
Display(OSD)
Main
menu
Sub
Adjustment
Description
menu
PICTURE
PICTURE
of the
BRIGHTNESS
To
adjust
the
CONTRAST
To
adjust
the contrast of the
GAMMA
Set your own gamma value. : -50/0/50
On the monitor, high gamma values
display whitish images and low gamma
values display high contrast images.
brightness
screen.
screen.
MENU : Exit
: Decrease
+ : Increase
SET : Select another sub-menu
-
COLOR
Select the screen color.
6500K: Slightly reddish white.
9300K: Slightly bluish white.
PRESET
COLOR
?
?
RED
Set your
own
red color levels.
GREEN
Set your
own
green color levels.
BLUE
Set your
own
blue color levels.
HORIZONTAL
To
move
image left
VERTICAL
To
move
image
MENU : Exit
: Decrease
+ : Increase
SET : Select another sub-menu
-
POSITION
POSITION
MENU : Exit
: Decrease
+ : Increase
SET : Select another sub-menu
-
A11
and
right.
up and down.
On Screen
Display(OSD)
Main
Selection and
Sub
menu
Adjustment
Description
menu
TRACKING
CLOCK
TRACKING
To minimize any vertical bars or stripes
visible on the screen background.
The horizontal screen size will also
change.
the focus of the display.
This item allows you to remove any
horizontal noise and clear or sharpen
the image of characters.
PHASE
To
MENU : Exit
: Decrease
+ : Increase
SET : Select another sub-menu
adjust
-
SETUP
LANGUAGE
To choose the
control
names
language in which
are displayed.
the
SETUP
MENU
-
+
of the OSD window
OSD
POSITION
To
adjust position
on
the
WHITE
BALANCE
If the output of the video card is different
the required specifications, the color
screen.
level may deteriorate due to video
signal distortion. Using this function, the
SET
SETUP
signal
level is
adjusted
to fit into the
standard output level of the video card
in order to provide the optimal image.
Activate this function when white and
black colors
MENU
-
+
SET
POWER
INDICATOR
MENU
-
:
+ :
SET
:
Exit
:
present in the
screen.
Use this function to set the power
indicator on the front side of the monitor
to ON
Adjust
Adjust
are
or
OFF.
If you set OFF, it will go off.
If you set ON at any time, the power
indicator will automatically be turned
Select another sub-menu
FACTORY
on.
Restore all factory default settings except
"LANGUAGE."
Press the
button to reset immediately.
RESET
If this does not improve the screen image, restore the factory default settings.
If necessary, perform the white balance function again. This function will be enabled
the input signal is an analog signal.
A12
only when
On Screen
A A A
Display(OSD)
The OSD
screen
Selection and
Adjustment
will appear when you touch the
(-)
button
on
the
right
side of the monitor.
Menu Name
Icons
Sub-menu Name
FLATRON F-ENGINE
Screen when
applied
Screen when not
applied
When you execute F-ENGINE, two tones will appear
on the screen as shown. The applied screen will
appear
screen
the left side, whereas the non-applied
will appear on the right side.Touch the SET
on
button to
use
Main
the
adjusted
screen.
Sub
menu
MOVIE
TEXT
Description
menu
This feature lets you easily select the best desired
image condition optimized to the environment
(ambient illumination, image types etc).
MOVIE: For animation
TEXT: For text
USER
images
in videos
or
movies
images (Word processing etc.)
User
You
manually adjust brightness, ACE or RCM.
You can save or restore the adjusted value even
when using a different environment setting.
To
adjust the
USER sub-menu
Press the SET Button
function,
can
(Brightness): Adjusts screen brightness.
...ACE(Adaptive Clarity Enhancer): Selects the clarity mode.
...RCM(Real Color Management): Selects the color mode.
...
0
Not
1
Green enhance
2
Flesh tone
3
Color Enhance
applied
Select the SAVE sub-menu using the SET button
and save the YES value using the buttons.
NORMAL This is under normal
A13
operating
conditions.
Troubleshooting
Check the
No
following before calling for service.
image
appears
Is the power cord of the
display connected?
Is the power indicator
light on?
Is the power on and the
power indicator blue or
?
Check and
properly
?
?
if the power cord is connected
to the power outlet.
see
Press the Power button.
Adjust the brightness
and the contrast.
green?
Is the power indicator
amber?
?
If the
the
mouse
is in power
saving mode, try moving
or pressing any key on the keyboard to
display
bring up the screen.
?TrytoturnonthePC.
Doyouseean"OUTOF
RANGE" message
the screen?
on
Do you see a "CHECK
SIGNAL CABLE"
message
on
?
This message appears when the signal from the
PC (video card) is out of horizontal or vertical
frequency range of the display. See the
'Specifications' section of this manual and
configure your display again.
?
This message appears when the signal cable
between your PC and your display is not
connected. Check the
the
signal
cable and try
again.
screen?
Do you
see a
"OSD LOCKED" message
Do you see "OSD
LOCKED" when you
push
MENU button?
?
You
so
that
they
the screen?
the current control
cannot be
settings,
inadvertently changed.
unlock the OSD controls at any time
pushing the MENU button for several
You
by
can secure
on
can
seconds: the message
"OSD UNLOCKED" will appear.
A14
Troubleshooting
Display image
Display
is incorrect
Position is
?
incorrect.
?
Press the AUTO/SET button to
automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, adjust the image
position using the H position and V position icon
in the on screen display.
Check Control Panel --> Display --> Settings
and see if the frequency or the resolution were
changed. If yes, readjust the video card to the
recommend resolution.
On the
screen
?
background, vertical
bars or stripes are
visible.
Any horizontal noise
appearing in any
image or characters
are not clearly
portrayed.
?
?
The
screen
mono or
color is
?
Press the AUTO/SET button to
automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, decrease the
vertical bars or stripes using the CLOCK icon
the on screen display.
Press the AUTO/SET button to
automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, decrease the
horizontal bars using the PHASE icon in the on
screen display.
Check Control Panel --> Display --> Settings
and adjust the display to the recommended
resolution or adjust the display image to the ideal
setting. Set the color setting higher than 24 bits
(true color).
Check if the
?
signal
cable is
properly connected
screwdriver to fasten if necessary.
Make sure the video card is properly inserted in
and
abnormal.
in
use a
the slot.
?
Set the color
at Control
The
screen
blinks.
?
?
setting higher than
Panel Settings.
Check if the
24 bits
(true color)
-
screen
is set to interlace mode and if
yes, change it to the recommend resolution.
Make sure the power voltage is high enough, It
has to be
higher than
A15
AC100-240V 50/60Hz.
Troubleshooting
Have you installed the
Have you installed the
display driver?
Doyouseean
"Unrecognized monitor,
Plug&Play (VESA DDC)
?
?
display
Be
driver?
display driver from the display
driver CD (or diskette) that comes with your
display. Or, you can also download the driver from
our web site: http://www.lge.com.
sure
Make
to install the
sure
to check if the video card
Plug&Play function.
monitor found"
message?
A16
supports
Specifications
Display
17 inch
17 inches (43.2 cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
17 inches viewable
0.264 mm pixel pitch
Sync Input
Horizontal
Vertical
Video
Input
Freq.
56
Freq.
30
Analog
Digital : 30
:
83 kHz (Automatic)
71 kHz (Automatic)
-
-
75 Hz (Automatic)
-
Input Form
Separate TTL, Positive/Negative
SOG (Sync On Green)
Digital
Signal Input
pin D-Sub Connector
DVI D connector (Digital)
RGB Analog (0.7 Vp-p/ 75 ohm), Digital
15
-
Input Form
Resolution
Max
Analog : VESA 1280 x 1024 @75 Hz
Digital : VESA 1280 x 1024 @60 Hz
Recommend
VESA 1280
Plug&Play
DDC 2B
Power
0n Mode
Sleep Mode
≤
Off Mode
≤1W
Dimensions
Width
36.8
&Weight
(with tilt/ swivel
stand)
Height
Consumption
Range
Input
35W
/ 14.49 inches
35.0 cm / 13.78 inches (Min)
42.5 cm / 16.73 inches (Max)
23.2 cm / 9.13 inches
5.6 kg (12.34 lbs)
Depth
cm
-5˚~25˚
350˚
Tilt
Swivel
Power
1024 @60 Hz
≤1W
Net
Tilt/Swivel
x
75 mm / 2.95 inches
Height range
AC 100-240V~50/60Hz 1.0A
Environmental
Conditions
Operating Conditions
Temperature 10˚C to 35 ˚C
10 % to 80 % non-Condensing
Humidity
Storage Conditions
Temperature -20˚C to 60 ˚C
5 % to 95 % non-Condensing
Humidity
Tilt/Swivel Stand
Attached(
), Detached ( O )
Attached(
), Detached ( O )
Signal
cable
Power cord
Wall-outlet type
or
PC-outlet type
NOTE
Information in this document is
subject to change without
A17
notice.
Specifications
19 inch
19 inches (48.19 cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
Display
19 inches viewable
0.294
mm
pixel pitch
Horizontal
Sync Input
Freq.
Vertical Freq.
Input Form
30
Analog
Digital : 30
:
56
83 kHz (Automatic)
71 kHz (Automatic)
-
-
75 Hz (Automatic)
-
Separate TTL, Positive/Negative
SOG (Sync On Green)
Digital
Video
Input
15
Signal Input
pin D-Sub Connector
DVI
D connector (Digital)
RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Input Form
Resolution
-
Max
Analog : VESA 1280 x 1024 @75 Hz
Digital : VESA 1280 x 1024 @60 Hz
Recommend
VESA 1280
Plug&Play
DDC 2B
Power
On Mode
Sleep Mode
Off Mode
≤
Dimensions
Width
41.3
&Weight
(with tilt/ swivel
stand)
Height
Consumption
Range
39W
≤1W
/ 16.26 inches
38.1 cm / 15.0 inches (Min)
45.6 cm / 17.95 inches (Max)
23.2 cm / 9.13 inches
6.2 kg (13.67 lbs)
Depth
cm
-5˚~25˚
350˚
Tilt
Swivel
Height
75
range
mm
/ 2.95 inches
Power Input
AC 100-240V~50/60Hz 1.0A
Environmental
Conditions
Operating Conditions
Temperature 10˚C
Signal
Power cord
to 60 ˚C
Attached(
), Detached ( O )
Attached(
), Detached ( O )
Wall-outlet type
non-Condensing
5 % to 95 % non-Condensing
Humidity
cable
to 35 ˚C
10 % to 80 %
Humidity
Storage Conditions
Temperature -20˚C
Tilt/Swivel Stand
1024 @60Hz
≤1W
Net
Tilt/Swivel
x
or
PC-outlet type
NOTE
Information in this document is
subject to change without
A18
notice.
Specifications
Preset Modes
(Resolution)
Display Modes (Resolution)
123456789
10
11
12
*13
VGA
VGA
VGA
VESA
VESA
VESA
MAC
VESA
VESA
MAC
VESA
VESA
VESA
*13 Mode
:
Horizontal
31.469
31.468
31.469
37.500
37.879
46.875
49.725
48.363
60.023
68.681
61.805
63.981
79.976
640 x 350
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1152 x 870
1152 x 900
1280 x 1024
1280 x 1024
Only Analog
Mode.
Indicator
MODE
LED Color
On Mode
green
Sleep Mode
amber
Off Mode
Freq. (kHz)
Off
A19
Vertical
Freq. (Hz)
70
70
60
75
60
75
75
60
75
75
65
60
75
Specifications
Connector Pin
Signal
1
8
917
16
Assignment
24
DVI-D Connector
Pin
Pin
Signal(DVI-D)
Signal(DVI-D)
T. M. D. S. Data2-
16
Hot
T. M. D. S. Data2+
17
T. M. D. S. Data0-
123456789
T. M. D. S. Data2/4 Shield
18
T. M. D. S. Data0+
T. M. D. S. Data4-
19
T. M. D. S. Data0/5 Shield
T. M. D. S. Data4+
20
T. M. D. S. Data5-
DDC Clock
21
T. M. D. S. Data5+
DDC Data
22
T. M. D. S. Clock Shield
23
T. M. D. S. Clock+
24
T. M. D. S. Clock-
Analog
Vertical
Sync.
T. M. D. S. Data1-
10
T. M. D. S. Data1+
11
T. M. D. S. Data1/3 Shield
12
T. M. D. S. Data3-
13
T. M. D. S. Data3+
14
+5V Power
15
Ground (return for +5V,
H. Sync. and V. Sync.)
T. M. D. S.
(Transition
Minimized Differential
A20
Signaling)
Plug
Detect
How to Install the VESA Standard wall
This monitor meets
mounting
VESA-compliant mounting
interface
pad
specifications.
VESA wall
mounting
Connected to another
object (stand type
and wall-
mounted type. This monitor accepts a VESAcompliant mounting interface pad.- optional)
For further
Mounting
information, refer
to the VESA Wall
Instruction Guide.
Kensington Security Slot- optional
Connected to a locking
cable that can be purchased
separately at most
computer
A21
stores
Digitally yours