The Monitor has an active matrix TFT (Thin-Film Transistor) LCD (Liquid Crystal Display). This monitor is designed for use in small working areas or for those who need more working space on the desk. Features The monitor is a 18.1-inch (18.1 inches viewable) intelligent micro-processor based monitor. USB(Universal Serial Bus) ports USB cable and hub. You such as a mouse, can keyboard - at the back of the monitor are easily and flexibly prepared for the designed devices and Plug Play function. connect USB to the monitor for true - The monitor has two signal connectors (D-sub and DVI) so that it can support existing analog input (D-sub) and an advanced standard digital input (DVI). Two computers can be simultaneously used while connected to this both an monitor. Digitally controlled auto-scanning is done with the micro-processor for horizontal frequencies between 30 and 80kHz, and vertical scan frequencies between 56 85Hz. The microprocessor-based intelligence allows the monitor to operate in each frequency mode with the precision of a fixed frequency scan - monitor. Plug and play capability if supported by your system. This monitor has E-DDC function.* Compliant with - - the EPA ENERGY STAR following regulated specifications :* Swedish TCO'99 * For detailed information, please refer to the Reference Guide provided . the Monitor Connecting To set up the monitor, ensure that the power is turned off to the system, and other attached devices, then follow these steps: 1 Place the monitor in 2 To adjust height of your monitor,unlock the stand lock the stand lock at arrows shown. A 3 Removed the stand 4 Connect the signal cable. When convenient, well-ventilated location a cover connecting the DVI Connect the end of monitor the slot and cable holder panel When PC connecting the Figure .......... Connect .....Figure 1 cable cable to the port on the rear panel of the monitor through Stand. 1 Connect the other end to the DVI port on the rear signal tighten Dsub the signal screws. 2 cable 2 end of the monitor one MAC panel Figure .......... one 5 on the rear on the panel rear of the 3 end of the monitor cable to either of the connectors signal of the monitor. Connect the other end of the monitor Macintosh computer 1 cable to either of the connectors signal of the monitor. Connect the other end to the Dsub port computer and tighten the screws. 2 panel Connect your computer. top of the stand.Push on of the monitor to connect the cables. signal on of the computer and near monitor, computer through Macintosh a adapter and then 1 cable to the screws. 2 signal tighten on rear the rear panel of One end of the power cord is connected into the power connetor on the back of the monitor. 3 Power ON/OFF Switch Figure 1 There should be DVI port on Stand Lock a the computer Stand Cover 3 2 DVI 1 Signal Cable 4 Power Cord Note : If you see the INPUT SIGNAL OUT OF RANGE message, check to make sure your system is set to one of the factory preset modes (see page A12), or is set to a resolution and refresh rate within the specification limits of this monitor. When For information conneting the DVI Analog, using a separately purchased adapter. on adapter requirements, contact your authorized dealer, reseller, provider. or A2 more service Connecting Figure the Monitor 2 Power ON/OFF Switch Stand Lock Stand Cover 3 2 Dsub 1 Signal Figure 4 Power Cord Cable 3 Power ON/OFF Switch Stand Lock Stand Cover 3 MAC Adapter MAC6 2 Dsub 1 4 Power Cord Signal Cable 6 Connect one end to a properly and close to the monitor. 4 7 After connecting cables, put stand cover correctly into the holes unders stand. If securely connected, you can hear click sound from the latch. 8 Power ON the PC, then the monitor. 9 If you see grounded AC outlet that is easily accessible the NO SIGNAL message, check the signal cable and connectors. 10 After using the system, power OFF the monitor, then the PC. NOTE : The figure3 shows the connection to an Apple Macintosh, using a separately purchased adapter. For more information on adapter requirements, contact your authorized dealer, reseller, or service provider. A3 Making use of USB (Universal Serial Bus) Bus) is an innovation in connecting your different desktop peripherals conveniently to your computer. By using the USB, you will be able to connect your mouse, keyboard, and other peripherals to your USB (Universal Serial monitor instead of having to connect them to your computer. This will give you greater flexibility in setting up your system. USB allows you to connect chain up to 120 devices on a single USB port, and you can "hot" plug (attach them while the computer is running) or unplug them while maintaining Plug and Plug auto detection and configuration. This monitor has an integrated BUS-powered USB hub, allowing up to 2 other USB devices to be attached it. USB connection 1. Connect the upstream port of the monitor to the downstream port of the USB compliant PC or another hub using the USB cable. (Computer must have a USB port) Connect the USB compliant peripherals to the downstream ports of the monitor. 2. USB upstream Poort USB downstream Ports To USB downstream of the USB port compliant PC another hub cable or Connect the cables from USB Mouse Keyboard compliant peripherals-such keyboard, mouse, etc as NOTE To activate the USB hub function, the monitor must be connected to PC(OS) or another hub with the USB cable(enclosed). When connecting the USB cable, check that the matches the shape at the connecting side. shape a USB compliant of the connector at the cable side Even if the monitor is in a power saving mode, USB compliant devices will function when are connected the USB ports(both the upstream and downstream) of the monitor. they IMPORTANT: These USB connectors such are not designed directly for video camera, scanner, etc. LGE recommends to the computer as a A4 use with high-power connecting high-power USB devices USB devices Pivot Function You can adjust the height of the screen and also rotate it 90o clockwise. (* For detailed information, please refer to the CD provided with the manual.) A5 Location and Function of Controls Front View Power Indicator Power Button SOURCE Button MENU Button Buttons AUTO/SET Button Power ON/OFF Switch Rear View Stand Lock Power Connector DVI port Dsub Signal port USB upstream port USB downstream ports A6 Control Panel Function Front Panel Controls AUTO/SET Button SOURCE Button MENU Button Power Button Power Indicator Button Control Function SOURCE Button Use this button to make Dsub or DVI connector active. This feature is used when two computers are connected to the monitor. The default setting is Dsub. MENU Button Use this button to enter or exit the Use these buttons to choose Button or on screen adjust display. items in the on display. screen <Shortcut ? 100 100 AUTO/SET Button Keys> Brightness and Contrast can be adjusted directly without entering the On Screen Display (OSD) buttons to adjust the system. Touch the settings and then the MENU button to save all changes. The Brightness and Contrast functions are also available in the On Screen Display (OSD) menu. Use this button to enter a selection in the on screen display. * AUTO adjustment function TO the AUTO/SET button before using OSD menu. This button is for the automatic adjustment of the screen PROCESSING AUTO CONFIGURATION position, clock and phase. Note: Some signal from some graphics boards may not function properly. If the results are unsatisfactory, adjust your monitor's Position, Clock and Phase manually. Power Button Use this button to turn the monitor on Power Indicator This indicator or off. lights up green when the monitor operates normally. If the monitor is in DPM (Energy Saving) mode (stand-by/ suspend/power off), this indicator color changes to amber. A7 Control Panel Function Front Panel Controls Control MENU, Function Button Press the hold the MENU button and button for 3 seconds: the message "CONTROLS LOCKED" appears. CONTROLS LOCKED You can pushing unlock the OSD controls at any time the MENU, button for 3 seconds: the message "CONTROLS UNLOCKED" will appear. CONTROLS UNLOCKED A8 by On Screen Display (OSD) Control Adjustment Making adjustments to the image size, position and operating parameters of the monitor are quick and easy with the On Screen Display Control system. A quick example is given below to familiarize you with the use of the controls. Following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the monitor to stabilize for at least 30 minutes before To make 12 adjustments Display, follow these steps: Press the MENU Button, then the main To access a becomes control, highlighted, Use the 345 in the On Screen use the making image adjustment. or menu of the OSD appears. Buttons. When the icon you want press the AUTO/SET Button. Buttons to adjust the item to the desired level. Accept the changes by pressing the AUTO/SET Button. Exit the OSD by Pressing the MENU Button. A9 On Screen You were Display(OSD) Selection introduced to the and Adjustment procedure of selection and adjusting an item the OSD system. Listed below are the icons, icon names, and icon of the items that are shown on the Menu. using descriptions Note : When a digital signal is set as an input,only CONTRAST,COLOR and SETUP properties adjust the other OSD can the be BRIGHTNESS, adjusted.you do not need to properties. Adjust Description Brightness BRIGHTNESS / CONTRAST Used to 88 adjust the brightness of the screen. 100 Contrast the desired. Adjust PRESET COLOR PRESET 9300K display 9300K/ 6500K To appear the 6500K to the contrast displays color temperature. ? RED ? GREEN 9300K:Slightly 6500K:Slightly bluish white. reddish white. BLUE RED To set your own color levels. GREEN To set your own color levels. BLUE To set your own color levels. POSITION Vertical Position 61 To move picture image up and down. 39 Horizontal Position To A10 move picture image left and right. On Screen Display(OSD) Selection OSD and Adjust Adjustment Description CLOCK TRACKING To minimize any vertical bars stripes visible on the screen background.The horizontal change. CLOCK or screen size will also PHASE To PHASE adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpen the of characters. image LANGUAGE To choose the SETUP LANGUAGE ENGLISH IMAGE SIZE FULL control language in which displayed. the names are OSD POSITION SIGNAL DSUB ANALOG 00000 H ELAPSED TIME firstname.lastname@example.orgHz IMAGE SIZE This function displays the image in its original enlarged size so as to fit the full screen of the LCD panel. size PRESET MODE DSUB ANALOG OSD POSITION To on SIGNAL or adjust position the in of the OSD window screen. To select DSUB ANALOG ANALOG / DIGITAL as or DVI the active input. This feature is used when two computers display. are The connected to the display automatically input when only detects the proper video ELAPSED TIME To A11 source display is connected. the use time of monitor one Video Memory Modes The monitor has 26 memory locations for factory preset to popular video modes. display modes, 16 of which are Display Modes (Resolution) Display Modes (Resolution) 123456789 Horizontal Freq.(kHz) Vertical Freq.(Hz) VGA 640 x 350 31.469 VGA 720 x 400 31.468 70 VGA 640 x 480 31.469 60 VESA 640 x 480 37.500 75 VESA 640 x 480 43.269 85 VESA 800 x 600 37.879 60 VESA 800 x 600 46.875 75 VESA 800 x 600 53.674 85 MAC 832 x 624 49.725 75 70 10 VESA 1024 x 768 48.363 60 11 VESA 1024 x 768 60.123 75 12 VESA 1024 x 768 68.677 85 13 MAC 1152 x 870 68.681 75 14 VESA 1152 x 900 61.805 65 15 VESA 1280 x 1024 63.981 60 16 VESA 1280 x 1024 79.976 75 User Modes Modes 17-26 are empty and can accept new video data. If the monitor detects a video mode that has not been present before or is not one of the preset modes, it stores the new mode automatically in one of the empty modes starting with mode 17. new If you use up the 10 blank modes and still have more new video modes, the monitor replaces the information in the user modes starting with mode 17. A12 Check the following before calling for service. Display Position is incorrect. Push the AUTO/SET Button. If the results are unsatisfactory, and V On the position icon screen in the adjust the image position using the display. background, vertical bars or stripes Push the AUTO/SET Button. If the results are unsatisfactory, decrease the vertical bars CLOCK icon in the on screen or in any image or are visible. stripes using the characters Push the AUTO/SET Button. If the results are unsatisfactory, decrease the horizontal bars on screen position display. Any horizontal noise appearing not clearly portraid. icon in the H on screen are using the PHASE display. NO SIGNAL message. The signal cable is not connected, or is loose. Check and secure the connection. INPUT SIGNAL OUT OF RANGE message appears. Picture is blank. The frequency of the signal from the video card is outside the operating range of the monitor. Horizontal Frequency: 30kHz 80kHz Vertical Frequency: 56Hz 85Hz - - * Use the graphics board's utility graphics board). software to change the frequency setting (Refer to the manual for * You F8 change the setup to the supported key during booting the system). can resolution using the Safe Mode (Press the The power LED is illuminated amber. The monitor is in its display power management mode. There is no active signal coming from the PC. The signal cable is not fastened securely. Check the computer power and graphics adapter configuration. The monitor doesn't enter the power saving off mode (Amber). Computer video signal is not VESA DPMS standard. Either the PC or the video controller card is not using the VESA DPMS power management function. Specifications Signal Connector Pin 1 8 917 16 24 Assignment C2 C1 C5 C3 C4 DVI Connector Pin Pin Signal(DVI) Signal(DVI) T. M. D. S. Data2- 16 Hot T. M. D. S. Data2+ 17 T. M. D. S. Data0- 123456789 T. M. D. S. Data2/4 Shield 18 T. M. D. S. Data0+ T. M. D. S. Data4- 19 T. M. D. S. Data0/5 Shield T. M. D. S. Data4+ 20 T. M. D. S. Data5- DDC Clock 21 T. M. D. S. Data5+ DDC Data 22 T. M. D. S. Clock Shield 23 T. M. D. S. Clock+ T. M. D. S. Data1- 24 T. M. D. S. Clock- 10 T. M. D. S. Data1+ C1 Analog Red 11 T. M. D. S. Data1/3 Shield C2 Analog Green 12 T. M. D. S. Data3- C3 Analog Blue 13 T. M. D. S. Data3+ C4 Analog H. 14 +5V Power C5 Analog Ground 15 Analog Vertical Sync. Ground (return for +5V, Sync. and V. Sync.) H. T. M. D. S. (Transition Minimized Differential A14 Signaling) Plug Detect Sync. Specifications Display 18.1inch (45.97cm) Flat Panel Active Type matrix-TFT LCD Anti-Glare Viewable Size Pixel Sync Input coating 18.1inch (45.97cm) 0.28 x 0.28mm pitch Horizontal 30kHz Vertical 56Hz Freq. Freq. - 80kHz (Automatic) 85Hz (Automatic) Separate TTL (Positive/Negative) Input form - Composite TTL (Positive/Negative) SOG (Sync On Green) Digital Video Input pin D-Sub connector / I connector (Digital/Analog) RGB Analog (0.7Vp-p/75ohm) Digital 15 Signal input DVI Input Form - Dsub VESA 1280 x 1024@75Hz Resolution - DVI - VESA 1280 x 1024@60Hz (Digital/Analog) VESA 1280 x 1024@60Hz Recommend USB USB standard specifications Downstream power supply 100mA for each (MAX) Communication speed 12 Mbps (full), 1.5 Mbps (low) 1 Upstream port USB port Rev. 1.0 complied BUS-powered hub 2 Downstream ports Power Normal(Max.) ≤ 55W Consumption Stand-by/Suspend ≤ 3W Power Off ≤3W Width Height 39.7cm / 15.6 inches 42.8cm / 16.85 inches (Min) 50.8cm / 20.0 inches (Max) Depth 23.7cm / 9.3 inches Dimensions Power Input Weight Tilt Range Environment Conditions AC 100-240V 50/60Hz 1.0A Net 8.5kg / 18.73lbs Tilt 5˚ (Down) / 30˚ (Up) Swivel 45˚ (Left) / 45˚ (Right) Operating condition 10˚C to 35˚C Temperature 10% to 80% non-condensing Humidity Storage condition -20˚C to 60˚C Temperature 5% to 95% non-condensing Humidity NOTE Information in this document is subject to change without A15 notice.